Local Integration Guide Main Job on site: 1 Use Weblmt to login the EnodeB 2 Add the OM link and check the link status 3 Add the board and GPS information; Check the GPS Status and VSWR of the ports. Steps of job:
1 Use Weblmt to login the eNodeB Use the Ethernet cable to connect to ETH port of LMPT board. Configure the IP 192.168.0.2 on laptop.
Use IE and visit the website: http://192.168.0.49/ Use the username admin; Password admin123 to login the eNodeB.
2 Add the OM link and check the link status SET DHCPSW: SWITCH=DISABLE;
DSP ETHPORT: SN=7, SBT=BASE_BOARD;
Local Configuration Negotiation Mode = AUTO Local Actual Negotiation Mode = AUTO
If you find wrong configuration, please use SET ETHPORT to modify as the picture below:
ADD DEVIP:
LST DEVIP:
LST DEVIP Result
ADD VLANMAP:
LST VLANMAP:
LST VLANMAP Result:
ADD OMCH:
[important step] PING 1. PING from Local IP to GW IP 2. PING from Local IP to destination IP Please make sure GW IP and destination IP are reachable.
DSP OMCH
DSP OMCH Result:
3 Add the board and GPS information; Check the GPS Status and VSWR of the ports. Run these commands as below: RMV RRU: CN=0, SRN=60, SN=0; RMV RRU: CN=0, SRN=61, SN=0; RMV RRU: CN=0, SRN=62, SN=0; RMV RRU: CN=0, SRN=63, SN=0; RMV RRU: CN=0, SRN=64, SN=0; RMV RRU: CN=0, SRN=65, SN=0; RMV RRU: CN=0, SRN=66, SN=0; RMV RRU: CN=0, SRN=67, SN=0; RMV RRU: CN=0, SRN=68, SN=0; RMV RRU: CN=0, SRN=69, SN=0; RMV RRU: CN=0, SRN=70, SN=0; RMV RRU: CN=0, SRN=71, SN=0; RMV RRU: CN=0, SRN=72, SN=0; RMV RRU: CN=0, SRN=73, SN=0; RMV RRU: CN=0, SRN=74, SN=0; RMV RRU: CN=0, SRN=75, SN=0; RMV RRU: CN=0, SRN=76, SN=0; RMV RRU: CN=0, SRN=77, SN=0; RMV RRUCHAIN: RCN=0; RMV RRUCHAIN: RCN=1; RMV RRUCHAIN: RCN=2; RMV RRUCHAIN: RCN=3;
RMV RRUCHAIN: RCN=4; RMV RRUCHAIN: RCN=5; RMV RRUCHAIN: RCN=6; RMV RRUCHAIN: RCN=7; RMV RRUCHAIN: RCN=8; RMV RRUCHAIN: RCN=9; RMV RRUCHAIN: RCN=10; RMV RRUCHAIN: RCN=11; RMV RRUCHAIN: RCN=12; RMV RRUCHAIN: RCN=13; RMV RRUCHAIN: RCN=14; RMV RRUCHAIN: RCN=15; RMV RRUCHAIN: RCN=16; RMV RRUCHAIN: RCN=17; RMV BRD: CN=0, SRN=0, SN=0; RMV BRD: CN=0, SRN=0, SN=1; RMV BRD: CN=0, SRN=0, SN=2; RMV BRD: CN=0, SRN=0, SN=3; RMV BRD: CN=0, SRN=0, SN=4; RMV BRD: CN=0, SRN=0, SN=5; RMV BRD: CN=0, SRN=0, SN=16; RMV BRD: CN=0, SRN=0, SN=18; RMV BRD: CN=0, SRN=0, SN=19; ADD BRD: CN=0, SRN=0, SN=3, BT=LBBP, WM=RAT_TDD; ADD BRD: CN=0, SRN=0, SN=16, BT=FAN; ADD BRD: CN=0, SRN=0, SN=18, BT=UEIU; ADD BRD: CN=0, SRN=0, SN=19, BT=UPEU; ADD RRUCHAIN: RCN=0, TT=CHAIN, HCN=0, HSRN=0, HSN=3, HPN=0; ADD RRUCHAIN: RCN=1, TT=CHAIN, HCN=0, HSRN=0, HSN=3, HPN=1; ADD RRU: CN=0, SRN=60, SN=0, TP=TRUNK, RCN=0, PS=0, RT=MRRU, RXNUM=4, TXNUM=4, RS=LO_TD, ALMPROCSW=ON; ADD RRU: CN=0, SRN=61, SN=0, TP=TRUNK, RCN=1, PS=0, RT=MRRU, RXNUM=4, TXNUM=4, RS=LO_TD, ALMPROCSW=ON; ADD GPS: SN=7, PRI=1; SET CLKSYNCMODE: CLKSYNCMODE=PHASE;
DSP GPS:; (Make sure the GPS Card State is Normal; And the GPS Satellites Traced is larger than 8.)
STR VSWRTEST:;(Make sure the VSWR result of RRU RF port connected is lower than 1500.)