Sectional and Utility Scaffold - Sutherlands Alice Rental Center jax scaffold... · 2014-04-24 · Continuous run scaffold (runs scaffold) means a two-point or multi-point fold const

S e c t i o n a l a n d U t i l i t y S c a f f o l d

M o r e t h a n l i f t i n g

Sectional Scaffold Utility Scaffold

Drywall Lifts/Carts Handy Roll

SAFETYPart Number DescriptionLL-204-22 Committment to safety package (includes - 1 Scaffold safety video,

20 frame decals, 25 LL-204-05 scaffold safety packets, and a lami-nated certificate.

LL-204-01 Tips on scaffold safety / safety rulse

LL-204-02 OSHA safety and health regulations for construction

LL-204-03 Recommended scaffold erection procedures

LL-204-04 Caution envelope with wire

LL-204-11 Instructions for erecting rolling towers

LL-204-05 Scaffold safety packet (includes - LL-244-01, LL-204-02, LL-204-03, LL-204-04, LL-204-11)

LL-204-27 Scaffold check guide cards

1 of 6

PART 1926 SUBPART L SCAFFOLDS

1926.450 SCOPE, APPLICATION AND DEFINITIONS APPLICABLE TO

THIS SUBPART.

(a) Scope and application. This subpart applies to all scaffolds used in

workplaces covered by this Part. It does not apply to crane or derrick sus-

pended personnel platforms, which are covered by Sec. 1926.550(g). The

criteria for aerial lifts are set out exclusively in Sec. 1926.453.

(b) Definitions

Adjustable suspension scaffold means a suspension scaffold equipped

with a hoist)s) that can be operated by an employee(s) on the scaffold.

Bearer (putlog) means a horizontal transverse scaffold member (which

may be supported by ledgers or runners) upon which the scaffold platform

rests and which joins scaffold uprights, posts, poles, and similar members.

Boatswains’ chair means a single-point adjustable suspension scaffold con-

sisting of a seat or sling designed to support one employee in a sitting posi-

tion.Body belt (safety belt) m

eans a strap with means both for securing it about

the waist and for attaching it to a lanyard, lifeline, or deceleration device.

Body harness means a design of straps which may be secured about the

employee in a manner to distribute the fall arrest forces over at least the thighs,

pelvis, waist, chest and shoulders, with means for attaching it to other compo-

nents of a personal fall arrest system.

Brace means a rigid connection that holds one scaffold member in a fixed

position with respect to another member, or to a building or structure.

Bricklayers’ square scaffold means a supported scaffold composed of

framed squares which support a platform.

Carpenters’ bracket scaffold means a supported scaffold consisting of a

platform supported by brackets attached to building or structural walls.

Catenary scaffold means a suspension scaffold consisting of a platform

supported by two essentially horizontal and parallel ropes attached to struc-

tural members of a building or other structure. Additional support may be

provided by vertical pickups.

Chimney hoist means a multi-point adjustable suspension scaffold used to

provide access to work inside chimneys. (See “Multi-point adjustable suspen-

sion scaffold.”)

Cleat means a structural block used at the end of a platform to prevent the

platform from slipping off its supports. Cleats are also used to provide footing

on sloped surfaces such as crawling boards.

Competent person means one who is capable of identifying existing and

predictable hazards in the surroundings or working conditions which are un-

sanitary, hazardous, or dangerous to employees, and who has authorization

to take prompt corrective measures to eliminate them.

Continuous run scaffold (runs scaffold) means a two-point or multi-point

adjustable suspension scaffold constructed using a series of interconnected

braced scaffold members or supporting structures to form a continuous scaf-

fold.Coupler means a device for locking together the tubes of a tube and coupler

scaffold.

Crawling board (chicken ladder) means a supported scaffold consisting of

a plank with cleats spaced and secured to provide footing, for use on sloped

surfaces such as roofs.

Deceleration device means any mechanism, such as a rope grab, rip-stitch

lanyard, specially-woven lanyard, tearing or deforming lanyard, or automatic

self-retracting lifeline lanyard, which dissipates a substantial amount of en-

ergy during a fall arrest or limits the energy imposed on an employee during

fall arrest.

Double pole (independent pole) scaffold means a supported scaffold

consisting of a platform(s) resting on cross beams (bearers) supported by

ledgers and a double row of uprights independent of support (except ties,

guys, braces) from any structure.

Equivalent means alternative designs, materials or methods to protect

against a hazard which the employer can demonstrate will provide an equal or

greater degree of safety for employees than the methods, materials or de-

signs specified in the standard.

Exposed power lines means electrical power lines which are accessible to

employees and which are not shielded from contact. Such lines do not in-

clude extension cords or power tool cords.

Reprinted from the August 30, 1996 Federal Registar

Department of Labor

Occupational Safety and Health Administration

29 CFR Part 1926

Safety Standards for Scaffolds Used in the Construction Industry;

Final Rule The effective date for this Standard is November 29,

1996 with some provisions effective September 27, 1997

Eye or eye splice means a loop with or without a thimble at the end of a wire

rope.Fabricated decking and planking means manufactured platforms made

of wood (including laminated wood and solid sawn wood planks), metal or

other materials.

Fabricated frame scaffold (tubular welded frame scaffold) means a scaf-

fold consisting of a platform(s) supported on fabricated end frames with inte-

gral posts, horizontal bearers, and intermediate members.

Failure means load refusal, breakage, or separation of component parts.

Load refusal is the point where the ultimate strength is exceeded.

Float (ship) scaffold means a suspension scaffold consisting of a braced

platform resting on two parallel bearers and hung from overhead supports by

ropes of fixed length.

Form scaffold means a supported scaffold consisting of a platform sup-

ported by brackets attached to formwork.

Guardrail system means a vertical barrier consisting of, but not limited to,

toprails, midrails, and posts, erected to prevent employees from falling off a

scaffold platform or walkway to lower levels.

Hoist means a manual or power-operated mechanical device to raise or

lower a suspended scaffold.

Horse scaffold means a supported scaffold consisting of a platform sup-

ported by construction horses (saw horses). Horse scaffolds constructed of

metal are sometimes known as trestle scaffolds.

Independent pole scaffold (see “Double pole scaffold”).

Interior hung scaffold means a suspension scaffold consisting of a plat-

form suspended from the ceiling or roof structure by fixed length supports.

Ladder jack scaffold means a supported scaffold consisting of a platform

resting on brackets attached to ladders.

Ladder stand means a mobile, fixed-size, self-supporting ladder consisting

of a wide flat tread ladder in the form of stairs.

Landing means a platform at the end of a flight of stairs.

Large area scaffold means a pole scaffold, tube and coupler scaffold, sys-

tems scaffold, or fabricated frame scaffold erected over substantially the en-

tire work area. For example: a scaffold erected over the entire floor area of a

room.Lean-to scaffold means a supported scaffold which is kept erect by tiltin

g it

toward and resting it against a building or structure.

Lifeline means a component consisting of a flexible line that connects to an

anchorage at one end to hang vertically (vertical lifeline) or that connects to

anchorages at both ends to stretch horizontally (horizontal lifeline) and which

serves a means for connecting other components of a personal fall arrest

system to the anchorage.

Lower levels means areas below the level where the employee is located

and to which an employee can fall. Such areas include, but are not limited to,

ground levels, floors, roofs, ramps, runways, excavations, pits, tanks, materi-

als, water, and equipment.

Mason’s adjustable supported scaffold (see “Self-contained adjustable

scaffold”).

Mason’s multi-point adjustable suspension scaffold means a continu-

ous run suspension scaffold designed and used for masonry operations.

Maximum intended load means the total load of all persons, equipment,

tools, materials, transmitted loads, and other loads reasonably anticipated to

be applied to a scaffold or scaffold component at any one time.

Mobile scaffold means a powered or unpowered, portable, caster or wheel-

mounted supported scaffold.

Multi-level suspended scaffold means a two-point or multi-point adjust-

able suspension scaffold with a series of platforms at various levels resting on

common stirrups.

Multi-point adjustable suspension scaffold means a suspension scaf-

fold consisting of a platform(s) which is suspended by more than two ropes

from overhead supports and equipped with means to raise and lower the

platform to desired work levels. Such scaffolds include chimney hoists.

Needle beam scaffold means a platform suspended from needle beams.

Open sides and ends means the edges of a platform that are more than 14

inches (36cm) away horizontally from a sturdy, continuous, vertical surface

(such as a building wall) or a sturdy, continuous, horizontal surface (such as a

floor), or a point of access. Exception: For plastering and lathing operations

the horizontal threshold distance is 18 inches (46cm).

Outrigger means the structural member of a supported scaffold used to

increase the base width of a scaffold in order to provide support for and in-

creased stability of the scaffold.

Outrigger beam (Thrustout) means the structural member of a suspen-

sion scaffold or outrigger scaffold which provides support for the scaffold by

extending the scaffold point of attachment to a point out and away from the

structure or building.

Outrigger scaffold means a support scaffold consisting of a platform rest-

ing on outrigger beams (thrustouts) projecting beyond the wall or face of the

building or structure, the inboard ends of which are secured inside the build-

ing or structure.

Overhand bricklaying means the process of laying bricks and masonry

units such that the surface of the wall to be jointed is on the opposite side of

the wall from the mason, requiring the mason to lean over the wall to com-

plete the work. It includes mason tending and electrical installation incorpo-

rated into the brick wall during the overhand bricklaying process.

125 Taylor Parkway, Archbold, OH 43502-9309

End PanelToeboard

Diagonal Brace

Insert

Side Panel

5 x 5 Step Frame

CasterCat-A-Corner Squaring Brace

Walkboard

Hinge PinRivet & Cotter Gravity Pig Tail Pin

Snap Pin

Outrigger

Tips on scaffold safeTy

The following safety tips are offered by the engineering depart-

ment of Bil-Jax, Inc. as guidelines in avoiding job-site situations

that could prove dangerous to scaffold workmen.

CheCk Safety CodeS:

OSHA, state and local safety codes should be consulted;

and approval obtained from Building Safety and Industrial

Commission on scaffold tips.InSpeCt and CheCk:

Take no chances. Inspect the scaffold set up after erection

and daily while in use. Don't remove or allow removal of, any

parts without the OK from the proper authorities. When wire

rope is used, inspect it on each job.BegIn WIth good footIng:

Use base plates, sills or footers (or

combination) on solid ground; make sure

scaffold is leveled or plumbed.

don't Short-Change BraCIng:

Use bracing at all points provided; add extra braces if needed to

insure stability.tIe SCaffold to the BuIldIng:

Scaffolding should be tied to the struc-

ture using heavy wire or tie-in devices.

The first vertical tie should be at the

maximum height of 4 times the narrowest

base dimension. Additional ties are not

to exceed 26 feet vertically. Maximum

horizontal distance between ties is not to

exceed 30 feet.don't overload SCaffoldIng:

Follow the safe load capacities as given

by the scaffold manufacturer. There's a

limit even to what steel can support. A

4-to-1 safety factor must be figured on

scaffolding.uSe Metal CatWalkS, platforMS;

Where available. If wood plank is used, it must be scaffold grade or

better. Inspect thoroughly before every job to make sure it is free from

breaks, knots, cracks or warpage. Decking should be full width.

don't rIde MovIng SCaffold;

and remember scaffold units are limited

in height to 4* times their narrowest base

dimension (unless base is widened by

outriggers, or more end frames; or tied

into building.) Always keep casters

locked. (except to re-spot) don't ClIMB BraCeS:

Use the steps provided on most steel

scaffolds to climb up to or down from

work levels. Use scaffold climbing

ladders where required.

proteCt WorkIng levelS:

Use overhead canopies to protect workers on lower work levels

when work is being done overhead. Rope off unsafe areas

underneath scaffold or provide wire mesh around work area.

uSe douBle guard raIlS;

and toeboards on exposed sides at

platform heights of 6 feet or more.

Courtesy of

Archbold, Ohio

POST WHERE WORKMEN CAN SEE

Do not use where user can come in contact with live power.

Page 1 of 2

reJeCt daMaged partS:

Bent or otherwise damaged end frames or braces should not be used.

Put them aside for replacement. For repair, call Bil-Jax, Inc.

fIrepolICeaMBulanCe

naMe

phone

Print Date 08-2006LL-204-01

*Exceptions: 3 times in CA, OH, OR, MT, ME.

© Bil-Jax, Inc. 2006

REPLACEMENT DECALSPart Number Description0202-0101 Panel guard caution decal

0202-0146 Caster decal (used on all BilJax casters)

0202-0242 Leveling caster / leveling jack extension decal

0202-0326 Scaffold frame caution decal

0202-0328 Personnel bracket warning decal

0202-0330 Guard railing decal

0202-0331 Walkboard / catwalk caution decal (Tuf-N-Lite)

0202-0335 Hoist arm warning decal

0202-0361 Expanded metal walkboard / catwalk decal

WARNING• PIN TO SCAFFOLD LEG BEFORE USE.• SET LOCK BEFORE CLIMBING AND

USING TOWER.• DO NOT USE IF LOCK IS FAULTY.

CCIG/FFO 0202-0146��

WARNING IMPROPER USE OF THIS

EQUIPMENT WILL RESULT IN SERIOUS INJURY OR DEATH.

CIA/RFO

For safety related questions, call (419) 445-8915 0202-0326

IN ADDITION TO THE ABOVE, FOLLOW ALL FEDERAL, OSHA, STATE AND LOCAL CODES AND REGULATIONS FOR THE PROPER USE OF THIS EQUIPMENT.


• DO NOT ride a moving scaffold.

• DO NOT use without guard rails or toeboards installed at all work levels.

• DO NOT stand or sit on guard rails.

• DO NOT move scaffold from on top.

• DO NOT stand on or climb crossbraces.

• DO NOT use crossbraces for a platform support.

• DO NOT exert horizontal force on top of a free standing scaffold.

• DO NOT use boxes, ladders, or any other means to increase the working height.

• DO NOT overload–check with your scaffold dealer for safe working loads.

• DO NOT enter platform from the crossbrace side of scaffold.

• DO NOT use side brackets on scaffold equipped with casters.

METAL CONDUCTS ELECTRICITY! DO NOT USE WHERE EQUIPMENT OR USER MAY CONTACT POWER LINES OR OTHER LIVE ELECTRICAL CIRCUITS.

Inspect scaffold daily and before each use.

USE:

ASSEMBLY: DO NOT use damaged or deteriorated equipment.

• Begin assembly with base plates and mud sills.

• DO NOT use unstable objects such as boxes, bricks, concrete blocks, etc. under scaffold legs.

Use only leveling jacks (maximum extension of 12 inches) to adjust to uneven surfaces.

• When stacking scaffold frames, always use insert pins and secure both ends of insert pins with fastening (lock) pins.

• Maximum free-standing height equals 3 times the smallest base dimension.

When height exceeds 3 times the smallest base dimension, when using side brackets, or when hoisting material, scaffold must be restrained from tipping by tying, guying, or other acceptable means.

Use approved stairs or access ladder to climb scaffold.

Fully deck each work level using metal catwalks, scaffold walkboards or approved scaffold plank.

Pin stem and set lock on all casters before using.

Use a diagonal horizontal brace (cat-a-corner) at base and every 20 ft. of height on rolling tower.

WARNING:CAP.75# PSF

CAP.75# PSF

• Inspect daily and before each use–do not use if damaged.• Keep surface free of debris.• Use only for designed purpose.• Acid and other corrosive substances will seriously reduce the

strength of the metal scaffolding components. Consult manu-facturer if using near acid.

• Do not exceed manufacturer's rated capacity.• Do not use ladder or any other means on platform to increase

work height.• Deck complete work platform area.

• Secure deck to prevent uplift with wire or other acceptablemeans.

• Do not use without guard rails and toeboards installed.• To avoid hook damage, do not drop walkboards.• Do not straighten bent hooks–bent hooks MUST be replaced

by the factory.• Do not use this platform in any type of cantilever application.

Never walk out onto or stand on any part of this platform whichextends beyond its point of support.

• Never ride a moving scaffold.

• Use only on scaffolding which is in good condition, plumb,square, rigid and level, and which is erected in accordancewith OSHA and ANSI codes and regulations.

• Only personnel familiar with OSHA and ANSI codes andregulations concerning the proper use of scaffolding shallbe allowed to erect and/or use this equipment.

• ADDITIONALLY, this equipment must be used in full com-pliance with all applicable OSHA and ANSI codes andregulation for scaffolding and related equipment.0202-0361 GFC

IMPROPER USE OF THIS EQUIPMENT WILL RE-SULT IN SERIOUS INJURY OR DEATH.

Metal conducts electricity. Do not use this equip-ment in areas where contact may be made withpower lines or other live electrical circuits. Failure tocomply with the preceding warning will result inserious personal injury or death. User MUST main-tain safe clearances at all times.

© bil-jax, inc. 2003

• Pincastertoextensionbeforeuse.

• Levelingjackextensionand/or leveling castermustbeheldsecurelywithin frame leg byLevelingStemRetainer.

• Setcaster lockbeforeclimbing and usingscaffold.

• Donotuseifcasterlockisfaulty.

UII/FFO 0202-0242

WARNING

MAXIMUM CAPACITY -500 LBS.

DO NOT EXCEED.

FAILURE TO COMPLYWITH THE ABOVE REGU-LATIONS MAY RESULTIN SERIOUS INJURY OR

DEATH.

METAL CONDUCTS ELEC-TRICITY! DO NOT USEWHERE EQUIPMENT ORUSER MAY CONTACTPOWER LINES OR OTHERLIVE ELECTRICAL CIRCUITS.

FOLLOW ALL FEDERAL,OSHA, STATE AND

LOCAL REGULATIONSFOR THE PROPER USEOF THIS EQUIPMENT.

PERSONNELBRACKET

• When side bracket is inuse, scaffold tower mustbe restrained from tippingby tying, guying or otheracceptable means.

• DO NOT use on scaffold-ing equipped with casters.

• Pin securely to frame be-fore use.

• When in use, all open sidesof work platform must haveguard rails installed.

• Inspect daily and beforeeach use. DO NOT use ifdamaged.

• For personneluse only.

• DO NOT usefor storage ofmaterial.

0202-0328LFT/COFR

WARNING


Page 2

Know Your Scaffold / Safety / Decals

Toll Free: 800-537-0540 Visit us at: www.biljax.com

Page 3

Frames

STEP FRAMES - specify tube size and lock typeDescription Weight5’ W x 2’ H Frame 23

5’ W x 3’ H Frame 27




5’ W x 6’ 4” H Frame 54

5’ W x 6’ 6” H Frame 47

Other step frames available - Contact factory

OPEN END FRAMES - specify tube size, lock type, and cane typeDescription Weight 3’ W x 6’ 4” H Frame 43

3’ W x 6’ 6” H Frame 40

4’ W x 6’ 4” H Frame 51

4’ W x 6’ 6” H Frame 46

5’ W X 6’ 4” H Frame 54

5’ W x 6’ 6” H Frame 50

Other open end frames available - Contact factory

Closed Cane 05

Open Cane 25

Frame Tube SizesTube Size Description5 Frame with 1 1/2” Leg O.D. (weighs 10% less than catalog listings)

6 Frame with 1 5/8” Leg O.D. (weighs same as catalog listings)

7 Frame with 1 11/16” O.D. (weighs 5% more than catalog listings)5 6 7

1-1/2” 1-5/8” 1-11/16”

Frame Lock TypesLock Type DescriptionJ-Lock J-Lock use with notched braces

C-Lock C-Lock use with holed braces

T-Lock T-Lock use with holed braces

U-Lock U-Lock use with holed braces

F-Lock F-Lock use with holed braces

J-Lock

C-Lock

T-Lock

U-Lock

F-Lock

DOUBLE STEP FRAMES - specify tube size and lock typeDescription Weight 5’ W x 3’ H Frame 27


5’ W x 4’ 6” H Frame 41



5’ W x 6’ 4” H Frame 54

5’ W x 6’ 6” H Frame 53

Other double step frames available - Contact Factory

All images are for illustration only. Haulotte Group | BilJax reserves the right to modify specifications without notice. Follow all applicable ANSI and OSHA codes/regulations when using this equipment. Do not use in ares where user can come in contact with live power.

Page 4

Frames (cont.) / Rolling Tower Packages

SIDEWALK FRAMES - specify tube size and lock typeDescription Weight 6’ W x 7’ 8” H Frame furnished with Hex Lock Nut 65

Other sidewalk frames available - Contact factory

CENTER ACCESS FRAMES - specify tube size and lock type (12” Rung Spacing)Description Weight 5’ W x 2’ H Frame 24





Other center access frames available - Contact factory

ROLLING TOWER PACKAGES - 5’ Wide - specify tube sizePart Number (5, 6, 7)z Range Work Ht. Weight7’ LengthsST-RU0711-( __ ) 2’ - 11’ 17’ 462

ST-RU0716-( __ ) 2’ - 16’ 22’ 568

ST-RU0716-( __ ) OR 2’ - 16’ 22’ 664

ST-RU0716-( __ ) OR 2’ - 21’ 27’ 775

ST-RU0716-( __ ) OR 2’ - 26’ 32’ 881

10’ LengthsST-RU1011-( __ ) 2’ - 11’ 17’ 542

ST-RU1018-( __ ) 2’ - 16’ 22’ 660

ST-RU1016-( __ ) OR 2’ - 16’ 22’ 756

ST-RU1021-( __ ) OR 2’ - 21’ 27’ 876

ST-RU1026-( __ ) OR 2’ - 26’ 32’ 946

ST-RU1031-( __ ) OR 2’ - 31’ 37’ 1105

ST-RU1036-( __ ) OR 2’ - 36’ 42’ 1220

PEDESTAL SCAFFOLD FRAME - specify tube size and lock typeDescription Weight Pedestal Scaffold Frame 37

Replacement Frame Only 17

Replacement Leg Only 10

OPEN LADDER FRAMES - specify tube size and lock type (12” Rung Spacing)Description Weight 5’ W x 6’ 4” H Frame 56

5’ W x 6’ 6” H Frame 57

Other open ladder frames available - Contact factory

LADDER FRAMES - specify tube size and lock typeDescription Weight Description Weight28” W x 3’ H Frame* 16 3’ W x 5’ H Frame 29.5

28” W x 4’ H Frame* 21 3’ W x 6’ H Frame 36

28” W x 5’ H Frame* 26 4’ W x 3’ H Frame 22.5

28” W x 6’ H Frame* 31 4’ W x 4’ H Frame 29

3’ W x 3’ H Frame 18.5 4’ W x 5’ H Frame 36

3’ W x 4’ H Frame 24 4’ W x 6’ H Frame 43

*Exact overall width measurement is needed when ordering 28” wide frames

Other ladder frames available - Contact factory


Pin Options / Fastening Pins / BracesINSERT PINS - specify tube size

Part Number (5, 6, 7) Description Weight0007-11___ 9” Pin with 1” collar (fits tube size 5) 90/ct

0007-022 9” Pin with 1/2” collar (fits tube size 6) 90/ct



0007-106 7” Pin without collar (fits tube size 6) 60/ct

0007-134 9” Pin with special collar (fits tube sizes 6, 7) 100/ct

0007-11_ 0001-022 0007-086 0007-031

0007-106

INSERT ATTACHMENT OPTIONS - specify tube sizePart Number (5 , 6 , 7) Description Weight0200-001 Rivet and cotter attachment

0200-002 Spring rivet attachment

0200-003__ Drive pin attachment0200-001 0200-0020200-003

Page 5

FASTENING PINSPart Number Description Weight0068-037-50 2” Rivet pin with cotter 4

0068-038-50 3” Rivet pin with cotter 5

0090-0496-50 Drive pin for permanent attachment (tube size 6) 2

0090-0494-50 Drive pin for permanent attachment (tube size 7) 2

0068-023-50 Spring rivet 2

006-0046-50 2” Gravity pig tail pin 9.1

0068-061-50 2” Snap pin 6

0068-100-50 2 1/2” Snap pin 8

0068-102-50 4 1/2” Snap pin 10

0068-012-50 2” Hinge pin 5

0068-018-50 3” Hinge pin 6.6

0066-00460068-0120068-018

0068-0230068-0370068-038

0068-061

0090-04950090-04960090-0494

CAT-A-CORNER SQUARING BRACES - specify tube sizePart Number (5, 6, 7) Description Weight0019-4__-507 Squaring brace for a 5’ wide x 7’ long tower 16

0019-4__-508 Squaring brace for a 5’ wide x 8’ long tower 18

0019-4__510 Squaring brace for a 5’ wide x 10’ long tower 20

Other Cat-A-Corner squaring braces available. Contact Factory

GALVANIZED DIAGONAL BRACES - specify end type and lock spacingDescription Weight5’ Brace 9

7’ Brace 12

8’ Brace 14

10’ Brace 17

Other diagonal braces available. Contact FactoryHole End Notch End

Lock Spacing

FrameSpacing

DOUBLE HOLE GALVANIZED DIAGONAL BRACES - 36” & 48” lock spacingPart Number Description Weight0010-34-07 7’ Spacing brace 12

0010-34-08 8’ Spacing brace 14

0010-34-10 10’ Spacing brace 17

Other diagonal braces available. Contact FactoryHole end type only


Page 6

Braces / Leveling Jacks / Base Plates / Guard Rails

LEVELING JACKS - specify tube sizePart Number (5, 6, 7) Description Weight0032-08__* Rigid jack 24” stem with 15” adjustment 10.2

0032-09__* Swivel jack 24” stem with 15” adjustment 12

0034-08__ Extension 15” adjustment with retainer kit 11.5

0069-0071 Leveling stem retainer 1

0032-085pl Plated rigid jack 24” stem with 15” adjustment 10.5

0032-086pl Plated swivel jack 24” stem with 15” adjustment 12.5

Other leveling jacks available. Contact Factory *To fit tube sizes 6 and 7, select 6 in the part number

BASE PLATES / RUBBER PAD - specify tube sizePart Number (5, 6, 7) Description Weight0030-11__ Rigid base plate - 4” stem 3

0030-12__ Swivel base plate - 4” stem 4

0082-0740 Rubber pad for base plate .5

GUARD RAIL POSTS - specify tube sizePart Number (5, 6, 7) Description Weight0023-__23 Corner guard rail post - B-lock 5.7

0023-__25 Corner guard rail post - F-lock 5.5

0023-__18 Guard rail post - U-lock 5.5

0023-__28 Corner guard rail post - U-lock 5.5

0032-08__ 0032-09__ 0034-08__

CASTERS - specify tube sizePart Number (5, 6, 7) Description Weight0026-7__2 8” wheel size - 4” stem size - 500 lb capacity (cast iron) 13

0026-9__2 8” wheel size - 4” stem size - 500 lb capacity (plastic) 9

0030-12__0030-11__

0026-7__2 0026-9__2

0023-__23 0023-__25 0023-__28

GUARD RAILS - GALVANIZED Part Number Description Weight0022-02-28 End rail - 28” spacing 3

0022-01-03 End rail - 36” spacing 3

0022-02-04 End rail - 46 1/2” spacing (fits tube size 5) 3

0022-01-04 End rail - 48” spacing (fits tube sizes 6, 7) 3

0022-02-05 End rail - 58 1/2” spacing (fits tube size 5) 4

0022-01-05 End rail - 60” spacing (fits tube sizes 6, 7) 4

0022-01-07 Side rail - 7’ spacing 5.25

0022-01-08 Side rail - 8’ spacing 6.5

0022-25-10 Side rail - 10’ spacing 8

Other side guard rail sizes available. Contact factory

ARM BRACES - 27 3/4” lock spacingPart Number Description Weight0013-15-07 7’ spacing brace - hole end 15

0013-15-08 8’ spacing brace - hole end 16

0013-15-10 10’ spacing brace - hole end 19

0013-03-07 7’ spacing brace - notch end 15

0013-03-10 10’ spacing brace - notch end 19

Other arm braces available. Contact FactoryHole End Notch End


Guard Rails / Toeboards / Easi-Guard System / Walkboards

6” STEEL TOEBOARDS Part Number Description Weight0012-016-03 End toeboard 26 5/8” (fits tube sizes 5,6) 4

0012-016-04 End toeboard 26 5/16” (fits tube size 7) 4

0012-016-05 End toeboard 36” (fits tube sizes 5, 6, 7) 5


0012-012-07 End toeboard 48” (fits tube sizes 6, 7) 6


0012-016-09 End toeboard 60” (fits tube sizes 6, 7) 7.8

0012-016-12 Side toeboard 7’ (fits tube sizes 5, 6, 7) 9

0012-016-14 Side toeboard 8’ (fits tube sizes 5, 6, 7) 10

0012-016-18 Side toeboard 10’ fits tube sizes (5, 6, 7) 12

TOEBOARD CLIPS Part Number Description Weight0063-0199 Toeboard clip .5

0063-0203 Corner toeboard bracket .5

EASI-GUARD SYSTEM - specify tube sizePart Number (5, 6, 7) Description Weight0012-23__ Mid-post 9

0012-22__-28 End panel 28” with toeboard 14




0012-209-07 Side panel 7’ 12

0012-209-08 Side panel 8’ 14

0012-210-10 Side panel 10’ 17

0012-202-07 Side toeboard 7’ steel 8

0012-202-08 Side toeboard 8’ steel 10

0012-202-10 Side toeboard 10’ steel 14.5

INTERMEDIATE GUARD RAIL FOR OPEN END TYPE FRAMESPart Number Description Weight0012-263-07 7’ Intermediate side guard rail panel 21

0012-263-08 8’ Intermediate side guard rail panel 23

0012-263-10 10’ Intermediate side guard rail panel 27

0012-267-05 5’ Wide Intermediate end guard rail panel 21.5

Other intermediate guard rail panel sizes available

0012-267-05

End panel

Side panel

Toeboard

Mid-post

Page 7

SWING GATEPart Number Description Weight0253-35 Swing gate for 5’ wide open end frames 22

X-PANDED STEEL WALKBOARD - STEEL FRAME WITH EXPANDED STEEL DECKPart Number Description Weight0044-205 19” Wide x 7’ long - 75 psf capacity 45

0044-225 24” Wide x 7’ long - 75 psf capacity 52





Other side guard rail sizes available. Contact factory


Page 8

Walkboards

TUF-N-LITE WALKBOARD REPLACEMENT PARTS Part Number Description Part Number Description0054-007-07 7’ Aluminum rail 4 mem / punch 0090-0545 1/4 - 20 x 1S / tap screw

0054-002-07 7’ Aluminum rail 3 mem / punch 0090-0987 3/16 drive rivet

0054-007-08 8’ Aluminum rail 4 mem / punch 0191-0019 Plywood for 0054-216



0054-102 Lock - swivel assembly, heavy duty A 0191-0050 Plywood for 0054-250

0054-101 Lock - swivel assembly, heavy duty B 0054-080 Conversion kit 2-bolt to 4 bolt

0054-130 Aluminum hook type A replacement kit

0054-131 Aluminum hook type B replacement kit

0054-018-05 Aluminum cross member for 19 walkboard



Other Tuf-N-Lite replacement parts available. Contact factory.

X-TRU-LITE WALKBOARD 7100 SERIES - ALUMINUM FRAME AND DECKPart Number Description Weight0055-216 19 1/4” Wide x 7’ long - 75 psf capacity 32

0055-220 19 1/4” Wide x 10’ long - 75 psf capacity 40

Other X-Tru-Lite walkboard sizes available. Contact factory.

X-TRU-LITE WALKBOARD REPLACEMENT PARTSPart Number Description Weight0055-216-3 End Support / 19” X-Tru-Lite 1

0082-0553 Aluminum hook repair kit - 1 hole 4

OUTRIGGER - specify tube size (5, 6, 7)Part Number (5, 6, 7) Description Weight0048-2__ 30” wide outrigger 14

TUF-N-LITE WALKBOARD ALUMINUM FRAME WITH PLYWOOD DECKPart Number Description Weight0054-216 19’ Wide x 7’ long - 75 psf capacity 32

0054-220-50 19’ Wide x 10’ long - 50 psf capacity 40

0054-220 19’ Wide x 10’ long - 75 psf capacity 46.5

0054-226 22’ Wide x 7’ long - 75 psf capacity 35

0054-230 22’ Wide x 10’ long - 50 psf capacity 44.5






Other Tuf-N-Lite walkboeard sizes available. Contact factory.

7/16"

2Type A Hook*

1-5/16"4Type B Hook

Type A part numbers listed. For Type B replace red 2 with a 4 in the part number


Plywood deck replacement

Aluminum hook replacement kit

Aluminum cross member

Brackets / Hoist Arm / Outrigger / PutlogsSIDE AND END BRACKETS - specify tube size Part Number Description Capacity Weight

SIDE BRACKETS0039-620-__ 20” Saddle hanger with tube end 500 lb 9

0039-624-__ 24” Saddle hanger with tube end 500 lb 10

0039-630-__ 30” Saddle hanger with tube end 500 lb 13

0039-165-__ 20” - 30” Adjustable saddle hanger with tube end 500 lb 14

0039-124 12” Saddle hanger with plate end 500 lb 6

0039-621 21” Saddle hanger with plate end 500 lb 9

0039-720-__ 20” Angle iron hanger - side hang-on with tube end 500 lb 9

0039-724-__ 24” Angle iron hanger - side hang-on with tube end 500 lb 11.5

0039-730-__ 30” Angle iron hanger - side hang-on with tube end 500 lb 13

0039-171-__ 20” - 30” Adjustable angle iron hanger with tube end 500 lb 14

END BRACKETS0039-520-__ 20” End and side hang-on with tube end 500 lb 10.5

0039-524-__ 24” End and side hang-on with tube end 500 lb 13

0039-530-__ 30” End and side hang-on with tube end 500 lb 14

END GUARD RAIL FOR SIDE BRACKET

0012-266 End guard rail for 20” to 30” side bracket 19

Page 9

0039-165-5 0039-520-5

0039-620-50039-621-5

HOIST ARM - WELL WHEEL - TIE BRACEPart Number Description Weight0041-028 Swivel head hoist arm 29

0082-0103 10” Well wheel 9.3

0063-0344 Scaffold tie brace 11

0012-266

0041-028

0063-0344

0082-0103

PUTLOGSPart Number Description Weight Part Number Description Weight0036-178 8 ‘ Putlog 24 0036-602 18’ Putlog - trussed 79

0036-180 10’ putlog 30 0036-603 20’ Putlog - trussed 92

0036-182 12’ Putlog 36 0036-604 22’ Putlog - trussed 101

0036-600 14’ Putlog - trussed 47 0036-605 24’ Putlog - trussed 111

0036-601 16’ Putlog - trussed 70 0036-606 26’ Putlog - trussed 118

Other putlog sizes available. Contact factory.

PUTLOG ACCESSORIESPart Number Description Weight0037-16 Putlog angle hanger 3.5

0061-11 Offset insert saddle (tube size 5) 3



0061-29 Insert saddle (tube size 5) 3



0037-22 Putlog support 8’ long with clamps 20

0036-040 Putlog spreader - 5’ frame sp (tube size 6) 24



Other putlog accessories available. Contract factory. 0037-160061-29 0061-06

0061-11 0061-12 0061-10

0037-22

0036-040 0036-042 0036-043


Putlog

Trussed putlog

Page 10

Clamps / Brackets / Replacement Parts / Stair Tower ComponentsDROPPED FORGED CLAMPS

Part Number Description Weight0069-0095 Swivel clamp with “Eye” bolt - fits 1.625”, 1.69”, 1.9” tube diamater 3

0069-0094 Rigid clamp with “Eye” bolt - fits 1.625”, 1.69”, 1.9” tube diamater 3

0069-0118 Swivel clamp with “Eye” bolt - fits 1.69” and 1.9” tube diamater 3

0069-0117 Rigid clamp with “Eye” bolt - fits 1.69” and 1.9” tube diamater 3

0069-0095 0069-0118

0069-0094 0069-0117

BRACKETS AND CLAMPSPart Number Description Weight0069-0017 Parallel tube clamp 1.5

0069-0016 Bracket for hole or notched brace .5

0069-0026 Bracket for hole brace .5

0069-0013 Clamp for notched brace 1.5

0069-0043 Clamp for hole brace 1.5

0069-0070 B-Lock clamp (tube size 5) .5

0069-0057 B-Lock clamp (tube size 6, 7) .5

0069-0015 0069-0013 0069-0017

0069-0043 0069-00260069-0070 0069-0057

REPLACEMENT PARTSPart Number Description Part Number Desciption0064-0783 Half outrigger clamp 0068-008 Lever tail nut 5” long

0066-0006 Putlog clamp hook 0068-042/1 Brace rivet with 3 washers

0067-0005 Gooser brace slide 0068-042/50 Package 50 brace rivets with 150 washers

0067-0039 Leveling nut (1 7/16”) 0068-095 U-Bolt only - Putlog angle hanger 0037-16

0067-0046 Leveling nut (1 1/4”) 0090-0517 Thumb screw - 3/8” diamater x 1 1/4” long

0068-004 1/2” set screw

0064-0783

0066-0006

0067-0005

0067-0739 0067-0046

0068-004

0068-008

0068-042/1

0068-095

0090-0517

BRACE LOCK PARTSPart Number Description Part Number Desciption0068-123A C-Lock with stud pin 0008-042 F-Lock complete

0068-123 C-Lock stud 0008-048 U-Lock complete

0064-0604 C-Lock slide 0068-009 J-Lock stud 1/2”

0008-022-4/50 C-Lock washer 0066-0044 J-Lock pin 3/8” x 3/4”

0090-0311/50 C-Lock roll pin 0068-013 J-Lock wing nut 1/2”

0008-044 T-Lock complete

0068-013

TUF-N-LITE HINGED LADDER BOARD - ALUMINUM FRAME, PLYWOOD DECK, ATTACHED LADDERPart Number Description Weight0054-125-07 28” Wide x 7’ long - 75 psf capacity 69

0054-125-08 28” Wide x 8’ long - 50 psf capacity 75

0054-125-10 28” Wide x 10’ long - 50 psf capacity 81

STAIR TOWER COMPONENTSPart Number Description Part Number Description0042-019 Stair platform rest (tube size 5) 0043-185 Outside handrail (top section)

0042-027 Stair platform rest (tube size 6) 0042-175 Inside handrail (top section)

0042-035 Stair platform rest (tube size 7) 0042-221 24” Wide stair section 6’ 5”

0042-047 Open frame safety guard 0042-022 24” Wide stair section 6’ 6”

0042-094 Outside handrail 0042-223 24” wide stair section 6’ 7”

0042-093 Inside handrail

0044-052 Intermediate catwalk 28” wide x 7’ long with guardrail

0044-054 Hinged platform 28” wide x 7’ long expanded steel

0044-235 28” Wide x 7’ Long expanded steel catwalk - 75 psf capacity


BilJax offers a heavy duty stair tower for worker access to buildings, bridges, observation towers, or renovation done inside or outside. The stairs can also be used for access in a scaffold set-up.

0068-0090064-0604

CLIMBING LADDER - TUBULAR TYPE (see below image)

Part Number Description Weight0004-0377 6’ Top section 19

0004-0375 6’ Ladder section 17.5

0004-0376 3’ Ladder section 9.2

0063-0074 Support bracket (tube size 5) 5.5

0063-0073 Support bracket (tube size 6, 7) 5.5

0004-0376

0063-0074 0063-0073

0004-0377

Access Ladder / Climbing LadderACCESS LADDER SYSTEM (see below image)

Part Number Description Weight0042-126 6’ Access ladder (use with 6’ 6” high frame) 37

0042-130 6’ Handrails (pair) 10.5

0042-129 Platform rest (tube size 5) (2 required at 1st tier only) 7.5

0042-128 Platform rest (tube size 6, 7) (2 Required at 1st tier only) 8

0054-346 Top hinged platform 28” x 7’ 43



0042-1260042-130

Top hinged platform

Page 11

CANOPY TOP / WEATHER PROTECTION CLIP (see below image)

Part Number Description Weight0071-021 Canopy top with adjustable extension - 5’ W x 1’ H (tube size 6) 27

0071-022 Canopy Top with adjustable extension - 5’ W x 1’ H (tube size 7) 27

0071-024 Canopy top with adjustable extension - 5’ W x 1’ H (tube size 5) 27

0082-0228 Weather protection clips 8” L 9 (qty. 100) 16

6’

Maximum 10’

Up to 4’

ADDITIONAL ILLUSTRATIONS

ACCESS LADDER SYSTEM CLIMBING LADDERTUBULAR TYPE

CANOPY TOPWEATHER PROTECTION CLIP


Page 12

Pro-Jax Scaffold Packages / Guard Rail

PRO-JAX UTILITY SCAFFOLD PACKAGES WITH PLYWOOD DECK WALKBOARDSPart Number Description Includes Weight

Length Platform Ht Range Guard Rails Outriggers0127-006-0 6’ 2’ - 4’ No No 147

0127-006-1 6’ 2’ - 6’ Yes No 240

0127-006-2 6’ 2’ -11.5’ Yes Yes 430

0127-006-3 6’ 2’ - 17’ Yes Yes 538

0127-008-0 8’ 2’ - 4’ No No 173

0127-008-1 8 2’ - 6’ Yes No 279

0127-008-2 8’ 2’ - 11.5’ Yes Yes 490

0127-008-3 8’ 2’ - 17’ Yes Yes 609

0127-010-0 10’ 2’ - 4’ No No 200

0127-010-1 10’ 2’ - 6’ Yes No 316

0127-010-2 10’ 2’ - 11.5’ Yes Yes 525

0127-010-3 10’ 2’ - 17’ Yes Yes 645

PRO-JAX UTILITY SCAFFOLD ADDITIONAL HEIGHT PACKAGESPart Number Description Weight0127-007-3 6’ Length x 39” height unit 75

0127-007-5 6’ Length x 65” height unit 95






PRO-JAX GUARD RAIL PACKAGES, OUTRIGGER PACKAGES, AND LEVELING EXTENSIONPart Number Description Weight0127-149-06 6’ Complete guard rail package (2 pieces) 81.5

0127-149-08 8’ Complete guard rail package (2 pieces) 98

0127-149-10 10’ Complete guard rail package (2 pieces) 115

0127-150-18 18” Wide outrigger package (4 pieces) 39

0127-150-24 24” Wide outrigger package (4 pieces) 44

0127-138 Leveling extension

0127-006-0

0127-006-1

0127-006-2

Single Unit

Single Unit w/ Guard Rail

2 Single Units w/ Guard Rail & 18” Wide Outriggers

0127-149-08

0127-150-18

0127-138

PRO-JAX COMPONENTS Part Number Description Weight

0127-102 39” High ladder frame 15

0127-101 65” ladder frame 25

0127-147 Base extension unit 29

0127-163-06 6’ Platform arm brace 21



0127-108-06 6’ Plywood deck 29

0127-108-08 8’ Plywood deck 40

0127-108-10 10’ Plywood deck 52

0127-141-06 6’ Top hinged plywood deck 47



0127-113 6’ Expanded metal deck 36

0127-114 8’ Expanded metal deck 48

0127-115 10’ Explanded metal deck 60

0127-106-06 6’ Combination guard panel 35.5

0127-106-08 8’ Combination guard panel 42

0127-106-10 10’ Combination guard panel 48

0127-105-18 18” Wide outrigger 8

0127-105-24 24” Wide outrigger 11

0127-118 48” Wide outrigger 26

0127-136-06 6’ Intermediate guard rail 20



0127-138 Adjustable leg with rubber pad 3

0026-835 5” Caster - 250 lb capacity with 2” snap pin (trailing edge brake lock) 4.75

0026-952 8” Caster - 500 lb capacity with 2” snap pin - P5 10

PRO-JAX REPLACEMENT PARTSPart Number Description Weight0063-0377 L-Pin replacement kit for platform arm brace .25

0063-0418 Wind latch replacement kit .25

0063-0605 Saf-T-Lok replacement kit .40

Pro-Jax Replacement Parts & Components / Handy Roll

Page 13All images are for illustration only. Haulotte Group | BilJax reserves the right to modify specifications without notice. Follow all applicable ANSI and OSHA codes/regulations when using this equipment. Do not use in ares where user can come in contact with live power.

HANDY ROLL SCAFFOLDING 4-CASTER UNITS Part Number Description Weight

0063-0435-34 3’ Handy roll scaffold 4-caster unit with steel platforms - 24” wide x 48” long x 39” high

82


87


106

0127-102

0127-101

0127-108-06

0127-113

0127-149-06

0127-163-06 0127-150-18 0026-835 0026-952

It shall be the responsibility of all employers and employees to read and comply with the following common sense guidelines which are designed to promote safety in the erecting and dismantling of scaffolds. These guidelines do not purport to be all-inclusive nor to supplant or replace other additional safety and precautionary measures to cover usual or unusual conditions. Local, State or Federal statute or regulations shall supersede these guidelines if there is a conflict and it is the responsibility of each employee to comply.

GENERAL GUIDELINESI. POST THESE SCAFFOLDING SAFETY GUIDELINES in a conspicuous place and be sure that all persons who erect, dismantle or use scaffolding are aware of them.II. FOLLOW ALL STATE, LOCAL AND FEDERAL CODES, ORDINANCES AND REGULATIONS pertaining to scaffolding because they may be more restrictive. For example, height or width requirements may vary.III. SURVEYTHEJOBSITE—Asurveyshallbemadeofthejobsiteforhazards,suchasuntamperedearthfills,ditches,debris,hightensionwires,unguardedopenings,andotherhazardousconditionscreatedbyothertrades.These

conditions shall be corrected or avoided as noted in the following sections.IV. INSPECT ALL EQUIPMENT BEFORE USING—Never use any equipment that is damaged or defective in any way.V. KEEP ALL EQUIPMENT IN GOOD REPAIR—Avoid using corroded equipment—the strength of corroded equipment is not known.VI. INSPECT ERECTED SCAFFOLDS DAILY—or at the beginning of every shift to be sure that they are maintained in safe condition.VII. NEVER USE EQUIPMENT FOR PURPOSES OR IN WAYS FOR WHICH IT WAS NOT INTENDED.VIII. REPORT ANY UNSAFE CONDITION. NEVER TAKE CHANCES—Do not work on scaffolds if your physical condition is such that you feel dizzy or unsteady in any way.IX. WORKING UNDER THE INFLUENCE OF ALCOHOL OR ILLEGAL DRUGS IS STRICTLY PROHIBITED.X. CONSULT YOUR SCAFFOLDING SUPPLIER—NEVER TAKE CHANCES—Consult manuals and instructions provided by the supplier; scaffolding is his business.

Scaffold Safety Guidelines - recommended by Scaffolding, Shoring & Forming Institute

GUIDELINES FOR ERECTION AND USE OF SCAFFOLDSA. PROVIDE ADEQUATE SILLS for scaffold posts and use base plates. B. USE ADJUSTING SCREWS or other approved conditions. C. PLUMBANDLEVELALLSCAFFOLDSastheerectionproceeds.Donotforcebracestofit—levelthescaffold

untilproperfitcanbemadeeasily. D. BRACING. Each frame or panel shall be braced by horizontal bracing, cross bracing, diagonal bracing or any

combination thereof for securing vertical members together laterally. All brace connections shall be made secure, in accordance with manufacturers’ recommendations.

E. DO NOT CLIMB CROSS BRACES. Use only an access (climbing) ladder, access steps, frame designed to be climbed or equivalent safe access to scaffold.

F. TIE RUNNING SCAFFOLD TO WALL or structure when the height exceeds* four (4) times the minimum scaffold basedimension.Thefirstverticalandlongitudinaltieshallbeplacedatthispoint.Verticaltiesshallberepeatedat intervals not greater than 26 feet. Longitudinal ties shall be placed at each end and at intervals not greater than 30 feet. Ties must prevent the scaffold from tipping into or away from the wall or structure.

G. WHENSCAFFOLDSARETOBEPARTIALLYORFULLYENCLOSED,specificprecautionsmustbetakentoassure frequency and adequacy of ties attaching the scaffolding to the building due to increased load conditions resulting from effects of wind and weather. The scaffolding components to which the ties are attached must also be checked for additional loads.

H. WHEN FREE STANDING SCAFFOLD TOWERS exceed* four times their minimum base dimension vertically, they must be restrained from tipping.

I. DO NOT ERECT SCAFFOLDS NEAR ELECTRICAL POWER LINES UNLESS PROPER PRECAUTIONS ARE TAKEN. Consult the power service company for advice.

J. DO NOT USE ladders or makeshift devices on top of scaffolds to increase the height. K. DO NOT EXCEED MANUFACTURERS’ RECOMMENDED LOAD RATING. L. EQUIP AND MAINTAIN ALL PLATFORMS with proper guardrails, midrails, and toeboards along all open sides

and ends of scaffold platforms. M. ALL BRACKETS shall be seated correctly with side brackets parallel to the frames and end brackets at 90 degrees

to the frames. Brackets shall not be bent or twisted from normal position. Brackets (except mobile brackets designed to carry materials) are to be used as work platforms only and shall not be used for storage of material or equipment. When brackets are used, the scaffold shall be tied to the structure or otherwise restrained to prevent tipping.

N. ALL SCAFFOLDING ACCESSORIES shall be used and installed in accordance with the manufacturers’ recom-mendedprocedure.Accessoriesshallnotbealteredinthefield.Scaffolds,framesandtheircomponentsofvarious manufacturers shall not be intermixed.

O. FOR PLANKING, THE FOLLOWING GUIDELINES APPLY: 1. Use only lumber that is properly inspected and graded as scaffold plank. 2. Planking shall have at least 12 inches of overlap and extend 6 inches beyond center of support, or, be

cleated at both ends to prevent sliding off supports.

3. Fabricated scaffold planks and platforms, unless created or restrained by hooks, shall extend over their end supports not less than 6 inches nor more than 12 inches.

4. Secure plank to scaffold when necessary. P. FOR ROLLING SCAFFOLDS THE FOLLOWING ADDITIONAL GUIDELINES APPLY.

1. CASTERS WITH PLAIN STEMS shall be attached to the panel or adjustment screw by pins or other suitable means.

2. DO NOT EXTEND ADJUSTING SCREWS ON ROLLING SCAFFOLDS MORE THAN 12 INCHES.3. WHEELS OR CASTERS shall be provided with a locking device and kept locked during erection and dismantling

or any time scaffolds are not being moved. 4. SECURE OR REMOVE ALL MATERIAL AND EQUIPMENT from platform before moving scaffold. 5. USE HORIZONTAL DIAGONAL BRACING near the bottom and at 20 foot intervals measured from the

rolling surface. 6. DO NOT USE brackets or other platform extensions without consideration of overturning effect. 7. THE HEIGHT OF A ROLLING SCAFFOLD excluding its uppermost guardrails, must not exceed* four times

its smallest base dimension unless it is stabilized by an engineered counterweight system or some other equivalent means.

8. CLEAT OR SECURE ALL PLANKS. 9. DO NOT ATTEMPT TO MOVE A ROLLING SCAFFOLD WITHOUT SUFFICIENT HELP—watch out for

holesinfloorandoverheadobstructions—stabilizeagainsttipping. 10. DO NOT RIDE ROLLING SCAFFOLDS. 11. JOINTS shall be restrained from separation.

Q. FOR “PUTLOGS” AND “TRUSSES” the following additional guidelines apply. 1. DO NOT CANTILEVER OR EXTEND PUTLOGS/TRUSSES as side brackets without thorough consideration

for loads to be applied. 2. PUTLOGS/TRUSSES SHOULD BE EXTENDED AT LEAST 6 inches beyond point of support. 3. PLACE RECOMMENDED BRACING BETWEEN PUTLOGS/TRUSSES when the span of putlog/truss is

more than 12 feet. R. WHEN DISMANTLING SCAFFOLDING THE FOLLOWING ADDITIONAL GUIDELINES APPLY: 1. CHECK TO SEE IF SCAFFOLDING HAS BEEN STRUCTURALLY ALTERED in any way which would make

it unsafe, and if so, reconstruct where necessary before commencing with dismantling procedures. 2. VISUALLY INSPECT PLANK prior to dismantling to be sure that they are safe to work on. 3. COMPONENTS SHOULD BE LOWERED as soon as dismantled in safe manner so as to protect personnel

below. 4. DO NOT ACCUMULATE EXCESS COMPONENTS OR EQUIPMENT on the level being dismantled. 5. DISMANTLED EQUIPMENT should be stockpiled in an orderly manner. S. FOLLOW ERECTION PROCEDURES AND USE MANUALS.

DRYWALL LIFT Part Number Description Capacity Weight

0063-0547 Model DL 100 Steel - 5’ to 10’ lift adjustment 200 104



DRYWALL CART Part Number Description Capacity Weight

0063-0573-01YE Model DC 3000 LD, light duty with plastic casters (2 swivel - 2 rigid) - 23” wide x 50” long x 47” high

3000 84

0063-0574-11YE Model DC 3000 MD, medium duty with steel casters (2 swivel - 2 rigid) - 23” wide x 49” long x 47” high

3000 104

0063-0575-11YE Model DC 3000 EX, heavy duty with steel casters (2 swivel - 2 rigid) - 28” wide x 50” long x 47” high

3000 137

0063-0575-11YE

0063-0580

Page 14

Drywall Cart / Drywall Lift

Page 15All images are for illustration only. Haulotte Group | BilJax reserves the right to modify specifications without notice. Follow all applicable ANSI and OSHA codes/regulations when using this equipment. Do not use in ares where user can come in contact with live power.

Other Offerings from Haulotte Group

SCAFFOLD FRAME MEASUREMENT CHARTSThese facts are needed whenever you are not sure that the frame is a BilJax brand product. If you do not have previous experience with the frame ordered, or if you do not have the item number, answer the below questions and provide them with your order.

Center access frame Ladder frame

Open frameStep frame

A. Specify Rotation of Pin Holes 1. 900 or 450 top & bottom 900 StandardB. Width of Frame Center to Center 1. To get this measurement, place tape outside to inside of leg tube.C. Frame Height 1. Measure overall top to bottom 2. DO NOT include insert (stacking pin) in measurementD. Lock Spacing 1. Measure distance from top of top lock pin to top of bottom lock pin 2. When a lock had two pins, use the lower pin of both locksE. Lock Location 1. Measure between top of leg and the center of the top lock pin 2. In case of a two pin lock, use the lower pinF. Tube Size of Leg (diameter) 1. Measure leg outside to outside 1-1/2”, 1-5/8”, 1-11/16” standard sizes

125 Taylor Parkway | Archbold | OH | 43502 |Toll Free: 800-537-0540 | Online at: www.biljax.com 0205

-201

3 ©

Hau

lotte

Gro

up |

BilJ

ax 2

013

- Prin

ted

in th

e U

SA

Documents

Sectional and Utility Scaffold - Sutherlands Alice Rental Center jax scaffold... · 2014-04-24 · Continuous run scaffold (runs scaffold) means a two-point or multi-point fold const