CoverRNCV200R009BSC6810 V200R011C00SPC100Parameter ReferenceHuawei Technologies Co., Ltd. provides customers with comprehensive technical support and service. For any assistance, please contact our local office or company headquarters.Huawei Technologies Co., Ltd.Address:Huawei Industrial BaseBantian, LonggangShenzhen 518129People's Republic of ChinaWebsite:http://www.huawei.comEmail:support@huawei.comCopyright Huawei Technologies Co., Ltd. 2009. All rights reserved.No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.Trademarks and Permissionsand other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.All other trademarks and trade names mentioned in this document are the property of their respective holders.NoticeThe information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute the warranty of any kind, express or implied.

&L&G&C&F&R&L&D&C&R&P&Nhttp://www.huawei.comsupport@huawei.com

About This DocumentPurposeThis describes RNC parameters, including the meaning, values, and usage of RNC parameters.VersionThe product version related to this document is: BSC6810 V200R011C00SPC100.Intended AudienceNetwork plannersField engineersSystem engineersShift operatorsOrganizationEach parameter is described in the following aspects.DescriptionRemarksParameter IDSimple string for identifying a parameterParameter NameFull name of the parameterMML CommandCommands for setting the parameter, and optional/mandatory attribute of the parameter in each commandNENEs on which the parameter is setMeaningFunctions, functioning ways, and protocols of the parameterValue TypeParameter value typeGUI Value RangeParameter value range displayed on the GUIActual Value RangeActual parameter value range corresponding to the GUI Value Range. For example, the GUI Value Range is 0, and the corresponding Actual Value Range is OFF.UnitParameter value unitDefault ValueInitial value provided by the systemRecommended ValueValues recommended in different scenariosImpactParameter impact scope, that is, objects specified when the parameter is setParameter RelationshipRelationship between this parameter and other parameters. For example, to use this parameter, you need to set related switches and parameters.Service Interrupted After ModificationWhether modifying the parameter value may interrupt the existing servicesInterruption ScopePossible interruption scope in the case that modifying the parameter value may interrupt the existing servicesInterruption Duration (min)Possible interruption duration in the case that modifying the parameter value may interrupt the existing servicesCautionCautions to be taken during the modificationAccessWhether this parameter is read/write or read onlyAttributeWhether this parameter is a radio parameter, a transport parameter, or an equipment parameterIntroduced in VersionVersion in which this parameter is introduced

&L&G&C&F&R&L&D&C&R&P&N

Parameter ListParameter IDParameter NameMML CommandNEMeaningValue TypeGUI Value RangeActual Value RangeUnitDefault ValueRecommended ValueImpactParameter RelationshipService Interrupted During ModificationInterruption ScopeInterruption Duration(min)CautionAccessAttributeIntroduced in VersionAAL2PATHTAAL2 Path TypeADD AAL2PATH(Mandatory)RNCThe type of service carried by the AAL2 path that users expect.Enumeration TypeR99, HSPA, SHARER99,HSPA,SHARENone-NoneAAL2 PathNoneN (No impact on the UE in idle mode)AAL2 PathNot involvedThe parameter modification has no impact on the equipment.Read & WriteTransportRAN11.0AbsTimeSpecify TimeSET POOLPRIMHOSTPOLICY(Mandatory)RNCThis parameter specifies the time to execute re-host policy for the primary hosted NodeB, after the RNC recovers from disaster and starts to operate.Compound Typehour, min, sec00:00:00~23:59:59s-NoneRNCThis paramter must be configured when [PARA]ReHostPolicy[/PARA] is set to REHOSTDELAY.N (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0Ac09ToAscAC 0~9 to ASC mappingADD PRACHACTOASCMAP(Optional)RNCIt defines the mapping of AC 0~9 to ASCs. For detailed information of this parameter, refer to 3GPP TS 22.011.Interval Type0~70~7None00CellThe ASCs are configured through [MML]ADD PRACHASC[/MML].N (Impact on random access for UEs in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0Ac10ToAscAC 10 to ASC mappingADD PRACHACTOASCMAP(Optional)RNCIt defines the mapping of AC 10 to ASCs. For detailed information of this parameter, refer to 3GPP TS 22.011.Interval Type0~70~7None00CellThe ASCs are configured through [MML]ADD PRACHASC[/MML].N (Impact on random access for UEs in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0Ac11ToAscAC 11 to ASC mappingADD PRACHACTOASCMAP(Optional)RNCIt defines the mapping of AC 11 to ASCs. For detailed information of this parameter, refer to 3GPP TS 22.011.Interval Type0~70~7None00CellThe ASCs are configured through [MML]ADD PRACHASC[/MML].N (Impact on random access for UEs in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0Ac12ToAscAC 12 to ASC mappingADD PRACHACTOASCMAP(Optional)RNCIt defines the mapping of AC 12 to ASCs. For detailed information of this parameter, refer to 3GPP TS 22.011.Interval Type0~70~7None00CellThe ASCs are configured through [MML]ADD PRACHASC[/MML].N (Impact on random access for UEs in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0Ac13ToAscAC 13 to ASC mappingADD PRACHACTOASCMAP(Optional)RNCIt defines the mapping of AC 13 to ASCs. For detailed information of this parameter, refer to 3GPP TS 22.011.Interval Type0~70~7None00CellThe ASCs are configured through [MML]ADD PRACHASC[/MML].N (Impact on random access for UEs in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0Ac14ToAscAC 14 to ASC mappingADD PRACHACTOASCMAP(Optional)RNCIt defines the mapping of AC 14 to ASCs. For detailed information of this parameter, refer to 3GPP TS 22.011.Interval Type0~70~7None00CellThe ASCs are configured through [MML]ADD PRACHASC[/MML].N (Impact on random access for UEs in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0Ac15ToAscAC 15 to ASC mappingADD PRACHACTOASCMAP(Optional)RNCIt defines the mapping of AC 15 to ASCs. For detailed information of this parameter, refer to 3GPP TS 22.011.Interval Type0~70~7None00CellThe ASCs are configured through [MML]ADD PRACHASC[/MML].N (Impact on random access for UEs in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0AccessServiceClassAccess service classADD PRACHASC(Mandatory)RNCIdentifying an ASC.Enumeration TypeASC0, ASC1, ASC2, ASC3, ASC4, ASC5, ASC6, ASC7ASC0, ASC1, ASC2, ASC3, ASC4, ASC5, ASC6, ASC7None-NonePhysical channelNoneNot involvedNot involvedNot involvedThis parameter cannot be modified.Read & WriteRadioVersions earlier than RAN11.0ACFCAddress and control field compressADD PPPLNK(Optional) ADD MPLNK(Optional)RNCThis parameter specifies whether to enable the address and control fields compression switch.Enumeration TypeDisable, EnableDisable (not support the address and control field compress function), Enable (support the address and control field compress function)NoneEnableEnablePPP Link(ADD PPPLNK) MLPPP Link, PPP Link(ADD MPLNK)NoneNot involvedNot involvedNot involvedThis parameter cannot be modified.Read & WriteTransportVersions earlier than RAN11.0AcIntervalOfCellAC Restriction Interval Of CellSET ACALGO(Mandatory)RNCInterval of automatic access classes restriction between cells. When a subsystem of an RNC performs access classes restriction on cells managed by this subsystem, it selects the first cell at random. After waiting for the time specified in this parameter, the subsystem selects the second cell and the first cell is still with access classes restriction. The process lasts until all the cells are going through access classes restriction. For detailed information of this parameter, refer to 3GPP TS 22.011.Interval Type1~3600010~360000, step:10ms-50RNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0AcIntervalOfCellsAccess Class Restriction interval between CellsSET DSACAUTOALGO(Mandatory)RNCSpecifies the interval between consecutive pollings imposed on the PS domain and CS domain in different cells according to the flexible polling restriction mode.Interval Type1~360001~36000s-100RNCWhen [PARA]DsacAutoSwitch[/PARA] is set to ON,the parameter need configure;else,need not configure.N (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0AcRangeRange of restrained Access ClassSET DSACAUTOALGO(Mandatory) ADD CELLDSACMANUALPARA(Mandatory)RNCSpecifies the restricted access class according to the flexible polling restriction mode.Bit Field TypeAC0(Access Class 0 Restriction), AC1(Access Class 1 Restriction), AC2(Access Class 2 Restriction), AC3(Access Class 3 Restriction), AC4(Access Class 4 Restriction), AC5(Access Class 5 Restriction), AC6(Access Class 6 Restriction), AC7(Access Class 7 Restriction), AC8(Access Class 8 Restriction), AC9(Access Class 9 Restriction), AC10(Access Class 10 Restriction), AC11(Access Class 11 Restriction), AC12(Access Class 12 Restriction), AC13(Access Class 13 Restriction), AC14(Access Class 14 Restriction), AC15(Access Class 15 Restriction)AC0,AC1,AC2,AC3,AC4,AC5,AC6,AC7,AC8,AC9,AC10,AC11,AC12,AC13,AC14,AC15None-AC0:BARRED,AC1:BARRED,AC2:BARRED,AC3:BARRED,AC4:BARRED,AC5:BARRED,AC6:BARRED,AC7:BARRED,AC8:BARRED,AC9:BARRED(SET DSACAUTOALGO) None(ADD CELLDSACMANUALPARA)RNCWhen [PARA]DsacAutoSwitch[/PARA] is set to ON,the parameter need configure;else,need not configure. If [MML]ADD CELLDSACMANUALPARA[/MML][PARA]RestrictionType[/PARA] value is RestrictionFixed,need set AcRestriction value;when [MML]ADD CELLDSACMANUALPARA[/MML][PARA]RestrictionType[/PARA] value is RestrictionFlexible,no need set AcRestriction value.N (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0AcRestrictionAC Restriction IndicatorADD CELLDSACMANUALPARA(Mandatory)RNCSpecifies the access classes that are restricted according to the fixed restriction mode.Bit Field TypeAC0(Access Class 0 Restriction), AC1(Access Class 1 Restriction), AC2(Access Class 2 Restriction), AC3(Access Class 3 Restriction), AC4(Access Class 4 Restriction), AC5(Access Class 5 Restriction), AC6(Access Class 6 Restriction), AC7(Access Class 7 Restriction), AC8(Access Class 8 Restriction), AC9(Access Class 9 Restriction), AC10(Access Class 10 Restriction), AC11(Access Class 11 Restriction), AC12(Access Class 12 Restriction), AC13(Access Class 13 Restriction), AC14(Access Class 14 Restriction), AC15(Access Class 15 Restriction)AC0,AC1,AC2,AC3,AC4,AC5,AC6,AC7,AC8,AC9,AC10,AC11,AC12,AC13,AC14,AC15None-NoneRNCIf [MML]ADD CELLDSACMANUALPARA[/MML][PARA]RestrictionType[/PARA] value is RestrictionFixed,need set AcRestriction value;when [MML]ADD CELLDSACMANUALPARA[/MML][PARA]RestrictionType[/PARA] value is RestrictionFlexible,no need set AcRestriction value.N (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0AcRstrctIntervalLenInterval length of Domain Specific Access Class RestrictionSET DSACAUTOALGO(Mandatory) SET ACALGO(Mandatory) ADD CELLDSACMANUALPARA(Mandatory)RNCSpecifies the interval delay between consecutive pollings according to the flexible polling restriction mode.Interval Type6~36006~3600s-10(SET DSACAUTOALGO) 30(SET ACALGO) None(ADD CELLDSACMANUALPARA)RNCWhen [PARA]DsacAutoSwitch[/PARA] is set to ON,the parameter need configure;else,need not configure. If [MML]ADD CELLDSACMANUALPARA[/MML][PARA]RestrictionType[/PARA] value is RestrictionFixed,need set AcRestriction value;when [MML]ADD CELLDSACMANUALPARA[/MML][PARA]RestrictionType[/PARA] value is RestrictionFlexible,no need set AcRestriction value.N (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0AcRstrctPercentAC Restriction PercentSET ACALGO(Mandatory)RNCAccess restriction ratio. When a cell performs access classes restriction, you can select some access classes from AC0 to AC9 based on the ratio specified in this parameter and perform access classes restriction on the selected access classes. After access classes restriction goes on for AcRstrctIntervalLen, the original access classes restriction is released and other access classes of the local cell are selected for access classes restriction based on the ratio specified in this parameter.Interval Type1~100.1~1, step:0.1per cent-2RNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0AcRstrctSwitchAC Restriction SwitchSET ACALGO(Optional)RNCOFF indicates that the AC algorithm is automatically disabled. ON indicates that the AC algorithm is automatically enabled.Enumeration TypeOFF, ONOFF, ONNone-OFFRNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0ACTOBJECTActivate ObjectACT LICENSE(Optional)RNCThis parameter specifies the license file to be activated. "Local" indicates the local license file is activated, and "SHARE" indicates that the shared value is activated.Enumeration TypeLOCAL(Local File), SHARE(Share Value)LOCAL,SHARENoneLOCALLOCALRNCNoneNot involvedNot involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteEquipmentVersions earlier than RAN11.0ACTTYPETypeACT GPS(Mandatory)RNCThis parameter specifies the type of the GPS assistance data to be activated.Enumeration TypeGPS(Global Position System), DGPS(Differential Global Position System), BOTH(both GPS and DGPS)GPS(Global Position System),DGPS(Differential Global Position System),BOTH(both GPS and DGPS)None-NoneRNCNoneNot involvedNot involvedNot involvedThe deleting operation can be done three minutes after ADD GPS operation.Read & WriteEquipmentVersions earlier than RAN11.0ACUAdded CPU occupancySTR CPUUSAGETST(Mandatory)RNCThis parameter specifies the CPU usage to be increased.Interval Type1~951 to 95per cent-NoneRNCNoneYSubsystemLess than 10 minutesCPU usage to be increased.Read & WriteEquipmentVersions earlier than RAN11.0AFSetObjAFSetObjSET ADMCTRL(Mandatory)RNCThe activity factor at the radio layer varies with the service priority. The configuration of the activity factor is performed based on the priorities of gold, silver, and copper. The activity factor of SRB is priority insensitive.Enumeration TypeNOPRIORITY(NOPRIORITY), GOLD(GOLD), SILVER(SILVER), COPPER(COPPER)NOPRIORITY, GOLD, SILVER, COPPERNone-NoneRNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0AgpsActivateFlagA-GPS Method Active FlagADD SMLCCELL(Optional)RNCFlag of A-GPS location activation.Enumeration TypeINACTIVE, ACTIVEINACTIVE, ACTIVENoneACTIVEACTIVECellValid when [PARA]CellLocCfgType[/PARA] is set to BOTH or CELL_ANTENNAN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0AGPSAddAssDataSendFlagA-GPS Additional Data Send FlagSET SMLC(Optional)RNCThis parameter indicates whether the GPS Additional Assistance Data Request is sent when the A-GPS method is used.Enumeration TypeNODELIVERY, DELIVERYNODELIVERY, DELIVERYNone-NODELIVERYRNCNoneN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0AGPSMethodTypeA-GPS Method TypeSET SMLC(Optional)RNCUE positioning mode when the A-GPS method is selected. The UE supports both UE-based A-GPS mode and UE-assisted A-GPS mode.Enumeration TypeUE_BASED, UE_ASSISTED, UE_BASED_PREFERRED, UE_ASSISTED_PREFERREDUE_BASED, UE_ASSISTED, UE_BASED_PREFERRED, UE_ASSISTED_PREFERREDNone-UE_BASEDRNCNoneN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0AGPSRECEIVERIDGPS IDADD GPS(Mandatory) ACT GPS(Mandatory)RNCThis parameter specifies a GPS reference receiver.Interval Type0~655340 to 65534None-NoneRNCNoneNot involvedNot involvedNot involvedThe deleting operation can be done three minutes after ADD GPS operation.Read & WriteEquipmentVersions earlier than RAN11.0AGPSRECEIVERTYPEGPS typeADD GPS(Mandatory)RNCThis parameter specifies the type of the GPS reference receiver. A GPS reference receiver can be configured on the local RNC, a NodeB of the local RNC, or a neighboring RNC.Enumeration TypeRNC(Local RNC), NODEB(Local NodeB), NRNC_RNC(Nearby RNC), NRNC_NODEB(NodeB in RNC)RNC(Local RNC), NODEB(Local NodeB), NRNC_RNC(Nearby RNC), NRNC_NODEB(NodeB in RNC)None-NoneRNC1. When the value of [PARA]AGPSRECEIVERTYPE[/PARA] in [MML]ADD GPS[/MML] is set to RNC, the GPS data report period, DGPS data report period, AGPS antenna latitude, AGPS antenna longitude, and AGPS antenna altitude should be set.1. When the value of [PARA]AGPSRECEIVERTYPE[/PARA] in [MML]ADD GPS[/MML] is set to NODEB, the cell ID, GPS data report period, DGPS data report period, AGPS antenna latitude, AGPS antenna longitude, and AGPS antenna altitude should be set.1. When the value of [PARA]AGPSRECEIVERTYPE[/PARA] in [MML]ADD GPS[/MML] is set to NRNC_RNC, the RNC ID, GPS data report period, DGPS data report period, AGPS antenna latitude, AGPS antenna longitude, and AGPS antenna altitude should be set.1. When the value of [PARA]AGPSRECEIVERTYPE[/PARA] in [MML]ADD GPS[/MML] is set to NRNC_NODEB, the RNC ID, cell ID, GPS data report period, DGPS data report period, AGPS antenna latitude, AGPS antenna longitude, and AGPS antenna altitude should be set.Not involvedNot involvedNot involved1. The AGPS reference receiver can be added to an RNC or a NodeB according to [AGPS type]. If the AGPS type is RNC, the AGPS reference receiver is added to the RNC. If the AGPS type is NodeB, the AGPS reference receiver is added to the NodeB. 2. One RNC can be configured with one AGPS reference receiver at most while one NodeB can be configured with five AGPS reference receivers at most. 3.If the AGPS reference receiver is configured in the RNC, the AGPS reference receiver must be integrated on the clock card. 4. If the AGPS reference receiver is added to a NodeB, the ID of the home cell of the AGPS reference receiver must be specified, and this cell must have been configured.5. If the AGPS reference recevier is added to an NRNC, the ID of the home RNC of the AGPS reference receiver must be specified and this NRNC must have been configured.6. If the AGPS reference recevier is added to a NodeB of an NRNC, the IDs of the home RNC and the home cell of the AGPS reference receiver must be specified, and the NRNC and the cell must have been configured. 7. If the AGPS reference receiver is added to a NodeB or a NodeB of an NRNC, one cell can be configured with only when AGPS reference receiver. 8. Be sure to remove GPS 3 minutes later after add it.Read & WriteEquipmentVersions earlier than RAN11.0AICHPowerOffsetAICH power offsetADD CHPWROFFSET(Optional)RNCDifference between the transmit power of AICH and that of PCPICH. If the value is set too small, the UEs on the cell edge cannot receive the acquisition indication properly. This problem affects the coverage of the downlink common channel and furthermore the coverage of the cell. If the value is set too great, it causes interference to other channels, occupies the downlink transmit power, and affects the cell capacity. For details, refer to the 3GPP TS 25.433 protocol.Interval Type-22~5-22~5dB-6-6CellNoneN (Impact on acquisition indicator receiving of UEs in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0AICHTxTimingAICH transmission timingADD AICH(Optional)RNCTransmission timing information of an AICH. "0" indicates that there are 7680 chips offset between the access preamble of the PRACH and AICH. "1" indicates that there are 12800 chips offset between them. For detailed information of this parameter, refer to 3GPP TS 25.211.Interval Type0~10~1None11Physical channelNoneNot involvedNot involvedNot involvedThis parameter cannot be modified.Read & WriteRadioVersions earlier than RAN11.0aidAlarm IDSET ALMLVL(Mandatory) SET BOXRPT(Mandatory) SET ALMPORT(Optional)RNCThis parameter specifies the alarm ID of the alarm configuration record to be modified.Interval Type1~655351~65535None-NoneRNC(SET BOXRPT,SET ALMLVL) SRB(SET ALMPORT)NoneNot involvedNot involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteEquipmentVersions earlier than RAN11.0AlignModealign typeSET HSSCCHLESSOPPARA(Mandatory)RNCThis parameter specifies whether the configured HS-SCCH Less Operation parameters adopt the octet_align or bit_align mode.Enumeration TypeBIT_ALIGN(Bit aligned mode), OCTET_ALIGN(Octet aligned mode)BIT_ALIGN, OCTET_ALIGNNone-NoneRNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0AllBwBandwidthADD RSCGRP(Mandatory)RNCThe unit is kbps. This parameter is valid only when Transport Resource Group Type is IP and Bandwidth mode is HALF_DUPLEX.Interval Type0~40000000~4000000kbit/s-NoneTransmission resource groupWhen [PARA]BWMODE[/PARA] in [MML]ADD RSCGRP[/MML] is set to HALF_DUPLEX, this parameter is valid;if the [PARA]BWMODE[/PARA] in [MML]ADD RSCGRP[/MML] of upper class and lower class RSCGRP is set to HALF_DUPLEX, the [PARA]AllBw[/PARA] in [MML]ADD RSCGRP[/MML] of upper class RSCGRP can not less than the [PARA]AllBwE[/PARA] in [MML]ADD RSCGRP[/MML] of lower class RSCGRP;The [PARA]AllBw[/PARA] in [MML]ADD RSCGRP[/MML] of upper class RSCGRP can not less than the sum of [PARA]TxBw[/PARA] and [PARA]RxBw[/PARA] in [MML]ADD RSCGRP[/MML] of lower class RSCGRP.N (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteTransportVersions earlier than RAN11.0AllocCodeModeAllocate Code ModeADD CELLHSDPA(Optional)RNCIf Manual is chosen, allocating [Code Number for HS-PDSCH] the equal of configured HS-PDSCH code number. If Automatic is chosen, allocating HS-PDSCH code number between configured HS-PDSCH Maximum code number and HS-PDSCH Minimum code number. At the early stage of network construction, or when the traffic model of subscribers in a cell is not fixed, the parameter can be set to Automatic to have the HSDPA channel codes be automatically allocated. If the traffic model of subscribers in a cell is fixed and known, the parameter can be set to Manual to select the static allocation mode. Manual allocation leads to restriction of HSDPA code resource or leaves HSDPA code resource idle. For detailed information of this parameter, refer to 3GPP TS 25.308.Enumeration TypeManual(Manual), Automatic(Automatic)Manual, AutomaticNoneAutomaticAutomaticCellNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0ALTITUDEGPS antenna altitudeADD GPS(Mandatory)RNCThis parameter specifies the antenna altitude of the GPS reference receiver.Interval Type-1000~10000-1000 to 10000m-NoneRNCWhen the value of [PARA]PGPSRECEIVERTYPE[/PARA] in [MML]ADD GPS[/MML] is selected, the ALTITUDE should be set.N (No impact on the UE in idle mode)Not involvedNot involvedThe parameter cannot be modified.Read & WriteEquipmentVersions earlier than RAN11.0ALTITUDEIMPGPS antenna altitudeADD GPS(Mandatory)RNCThis parameter specifies the antenna altitude of the GPS reference receiver. (IMP unit: Feet)Interval Type-3281~32810-3281~32810None-NoneRNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter cannot be modified.Read & WriteEquipmentRAN11.0alvlAlarm SeveritySET ALMLVL(Mandatory)RNCThis parameter specifies the alarm severity to be set.Enumeration TypeCritical(Critical), Major(Major), Minor(Minor), Warning(Warning)Critical,Major,Minor,WarningNone-NoneRNCNoneNot involvedNot involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteEquipmentVersions earlier than RAN11.0AmntOfRpt2B2B event retry max timesADD CELLINTERFREQHOCOV(Optional) SET INTERFREQHOCOV(Optional)RNCMaximum number of times for event 2B retry.This parameter defines the number of times for event 2B retry when the measurement control is valid. The larger the value of this parameter, the larger the number of times for inter-frequency handover retry, and the higher probability for the UE to be successfully handed over to the target cell whose load is restored. After the maximum number of times for event 2B retry, the RNC sends the inter-frequency measurement control message again to hand over the UEs to the other cells of this frequency.If the measurement control message is released, the retry will be immediately stopped.Interval Type0~630~62, 63: InfinityNone4(ADD CELLINTERFREQHOCOV) -(SET INTERFREQHOCOV)4Cell(ADD CELLINTERFREQHOCOV) RNC(SET INTERFREQHOCOV)This parameter is valid when [PARA]InterFreqReportMode[/PARA] is set to EVENT_TRIGGER.N (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0AmntOfRpt2C2C event retry max timesADD CELLINTERFREQHONCOV(Optional) SET INTERFREQHONCOV(Optional)RNCMaximum retry times of the event 2C.This parameter defines the number of times for event 2C retry when the measurement control is valid.The larger the value of this parameter, the larger the number of times for inter-frequency handover retry, and the higher probability for the UE to be successfully handed over to the target cell whose load is restored. When the retry times reaches the maximum value, the RNC stops the retry process. Or if the measurement control message is released, the retry will be immediately stopped.Interval Type0~630~62, 63: InfinityNone1(ADD CELLINTERFREQHONCOV) -(SET INTERFREQHONCOV)1Cell(ADD CELLINTERFREQHONCOV) RNC(SET INTERFREQHONCOV)NoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0AmntOfRpt3A3A event retry max timesADD CELLINTERRATHOCOV(Optional) SET INTERRATHOCOV(Optional)RNCMaximum retry times of the event 3A.This parameter defines the number of times for event 3A retry when the measurement control is valid. The larger the value of this parameter, the larger the number of times for inter-RAT handover retry, and the higher probability the UE is successfully handed over to the target cell whose load is restored. When the retry times reaches the maximum value, the RNC stops the retry process. Or if the measurement control message is released, the retry will be immediately stopped.Interval Type0~630~62, 63: InfinityNone4(ADD CELLINTERRATHOCOV) -(SET INTERRATHOCOV)4Cell(ADD CELLINTERRATHOCOV) RNC(SET INTERRATHOCOV)This parameter is valid when [PARA]InterRatReportMode[/PARA] is set to EVENT_TRIGGER.N (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0AmntOfRpt3C3C event retry max timesADD CELLINTERRATHONCOV(Optional) SET INTERRATHONCOV(Optional)RNCMaximum retry times of the event 3C.This parameter defines the number of times for event 3C retry when the measurement control is valid. The larger the value of this parameter, the larger the number of times for inter-RAT handover retry, and the higher probability the UE is successfully handed over to the target cell whose load is restored. When the retry times reaches the maximum value, the RNC stops the retry process. Or if the measurement control message is released, the retry will be immediately stopped.Interval Type0~630~62, 63: InfinityNone1(ADD CELLINTERRATHONCOV) -(SET INTERRATHONCOV)1Cell(ADD CELLINTERRATHONCOV) RNC(SET INTERRATHONCOV)NoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0AmRlcCfgParaRLC AM mode parameters selectionADD TYPRABRLC(Mandatory)RNCThis parameter specifies to edit sender parameters, receiver parameters, or flow control parameters.Enumeration TypeSENDER_PARA, RECEIVE_PARA, FLOWCONTROL_PARASENDER_PARA, RECEIVE_PARA, FLOWCONTROL_PARANone-NoneRABThis parameter is required when the [PARA]RlcMode[/PARA] parameter is set to AM.N (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0AMRQosPerformQOS Switch For AMR TrafficSET QOSACT(Optional)RNCWhen the parameter is set to YES, the QOS control algorithm is used for AMR services. When the parameter is set to NO, the QOS control algorithm is not used for AMR services.The QOS actions of AMR services include rate downsizing, inter frequency handover and inter rat handover.Enumeration TypeNO, YESNO, YESNone-NORNCNoneN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0AmrRabAbnormRelRatioThdAMR call drop ratio Per SpuSET KPIALMTHD(Optional)RNCAMR CDR(Call Drop Ratio) Per Spu, if the ratio is higher than this threshold in a checking period, need arise KPI alarm.Interval Type0~1000~100None-5RNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0AmrRabEstabAttMinNumThe minimum of AMR Rab attempt setup Per SpuSET KPIALMTHD(Optional)RNCThe minimum number of AMR service attempt Per Spu, the sum of AMR service attempt need to be higher than this threshold to arise KPI alarm which type is AMR service successful setup ratio.Interval Type0~655340~65534None-100RNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0AmrRabEstabSuccRatioThdAMR Rab successful setup ratio Per SpuSET KPIALMTHD(Optional)RNCSuccessful AMR service setup ratio Per Spu, if the ratio is lower than this threshold in a checking period, need arise KPI alarm.Interval Type0~1000~100None-90RNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0AmrRabRelMinNumThe number of AMR drop Per SpuSET KPIALMTHD(Optional)RNCThe Minimum number of AMR release Per Spu, the sum of AMR release need to be higher than this threshold to trigger arise KPI alarm which type is AMR call drop ratio.Interval Type0~655340~65534None-200RNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0AmrUlRateAdjTimerLenWait Timer For AMR Uplink RateSET QOSACT(Optional)RNCTimer for triggering a second adjustment of the UL AMR mode. This parameter specifies the duration of waiting for the voice quality enhanced acknowledgement after the UL AMR mode adjustment when the associated command is delivered. The UL AMRC rate adjust timer starts when AMRC mode adjustment procedure is triggered, and stops when the next measurement report is received. If no measurement report is received when the UL AMRC timer expires, you can infer that the measured value remains in the same state as that before the previous UL AMRC mode adjustment. The previous AMRC mode adjustment is not effective, and another adjustment is required. The longer the UL AMRC timer is, the less frequently the AMRC mode is adjusted. In addition, the response to measurement reports becomes slower accordingly.Interval Type20~6400020~64000ms-3000RNCValid when [PARA]AMRQosPerform[/PARA] is set to YESN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0ANIAdjacent Node IDADD ADJNODE(Mandatory) ADD AAL2PATH(Mandatory) ADD AAL2RT(Mandatory) ADD ADJMAP(Mandatory) ADD IPPATH(Mandatory) ADD IPPATHBIND(Mandatory) ACT IPPM(Mandatory) ACT VCLCC(Mandatory) LOP VCL(Mandatory)RNCID of the adjacent node. An RNC can be configured with at most 2000 adjacent nodes.Interval Type0~19990~1999None-NoneAdjacent Node(ACT VCLCC,ADD ADJMAP,ADD ADJNODE) AAL2 Path(LOP VCL,ADD AAL2PATH) Services carried on the network element with the specific ATM address.(ADD AAL2RT) IP Path(ADD IPPATHBIND,ADD IPPATH) IP path(ACT IPPM)The adjacent node is already configured by [MML]ADD ADJNODE[/MML]. When the value of [PARA]LNKT[/PARA] in [MML]ACT VCLCC[/MML] is set to AAL2PATH, the adjacent node ID should be set. When the value of [PARA]LNKT[/PARA] in [MML]LOP VCL[/MML] is set to AAL2PATH, the value of [PARA]ANI[/PARA] should be set.Not involvedNot involvedNot involvedThis parameter cannot be modified.Read & WriteTransportVersions earlier than RAN11.0AntennaAltitudeMeterCell Antenna AltitudeADD SMLCCELL(Optional)RNCAltitude of the cell antenna in the WGS-84 coordinates. This is a necessary parameter, controlled by MTRLGY and valid when MET~0(metric system).The value of this parameter has effect on the location result.Interval Type-32767~32767-32767~32767m-NoneCellValid when [PARA]CellLocCfgType[/PARA] is set to BOTH or CELL_ANTENNAN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteEquipmentVersions earlier than RAN11.0AntennaAltitudeMeterImpCell Antenna AltitudeADD SMLCCELL(Optional)RNCAltitude of the cell antenna in the WGS-84 coordinates. This is controlled by MTRLGY and valid when IMP~1(British measurement).The value of this parameter has effect on the location result.Interval Type-107502~107502-107502~107502m-NoneCellValid when [PARA]CellLocCfgType[/PARA] is set to BOTH or CELL_ANTENNAN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteEquipmentRAN11.0AntennaLatitudeDegreeCell Antenna LatitudeADD SMLCCELL(Optional)RNCLatitude of the cell antenna in the WGS-84 coordinates. The value corresponding to the latitude A degrees B minutes C seconds is [A + (B/60) + (C/3600)] / 0.000001.For example, the value corresponding to the latitude 31 degrees 30 minutes 36 seconds is [31 + (30/60) + (36/3600)] / 0.000001 = 31510000.This is controlled by GCDF and valid when DEG~0(degree format).The value of this parameter has effect on the location result.Interval Type-90000000~90000000-90~90, step: 0.000001degree-NoneCellValid when [PARA]CellLocCfgType[/PARA] is set to BOTH or CELL_ANTENNAN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteEquipmentVersions earlier than RAN11.0AntennaLatitudeDegreeSecCell Antenna LatitudeADD SMLCCELL(Optional)RNCThis parameter specifies the latitude of the cell antenna in the WGS-84 coordinates. The input format is ddd:mm:ss.ssss.This is controlled by GCDF and valid when SEC~1(degree, minute, second format).The value of this parameter has effect on the location result.String Type--90~90second-NoneCellValid when [PARA]CellLocCfgType[/PARA] is set to BOTH or CELL_ANTENNAN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteEquipmentVersions earlier than RAN11.0AntennaLongitudeDegreeCell Antenna LongitudeADD SMLCCELL(Optional)RNCLongitude of the cell antenna in the WGS-84 coordinates. The value corresponding to the longitude A degrees B minutes C seconds is [A + (B/60) + (C/3600)] / 0.000001.For example, the value corresponding to the longitude 121 degrees 40 minutes 36 seconds is [121 + (40/60) + (36/3600)] / 0.000001 = 121676666. This is controlled by GCDF and valid when DEG~0(degree format).The value of this parameter has effect on the location result.Interval Type-180000000~180000000-180~180, step: 0.000001degree-NoneCellValid when [PARA]CellLocCfgType[/PARA] is set to BOTH or CELL_ANTENNAN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteEquipmentVersions earlier than RAN11.0AntennaLongitudeDegreeSecCell Antenna LongitudeADD SMLCCELL(Optional)RNCLongitude of the cell antenna in the WGS-84 coordinates. The input format is ddd:mm:ss.ssss. This is controlled by GCDF and valid when SEC~1(degree, minute, second format).The value of this parameter has effect on the location result.String Type--180~180second-NoneCellValid when [PARA]CellLocCfgType[/PARA] is set to BOTH or CELL_ANTENNAN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteEquipmentRAN11.0AntennaOpeningCell Antenna OpeningADD SMLCCELL(Mandatory)RNCCoverage angle of a sector. For an omni-directional cell, the value is 360.The value of this parameter has effect on the location result.Interval Type0~36000~360, step: 0.1degree-NoneCellValid when [PARA]CellLocCfgType[/PARA] is set to BOTH or CELL_ANTENNAN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteEquipmentVersions earlier than RAN11.0AntennaOrientationCell Antenna OrientationADD SMLCCELL(Mandatory)RNCAzimuth of the main lobe of the cell antenna (the counter-clockwise angle from the direction of the main lobe to the north).The value of this parameter has effect on the location result.Interval Type0~36000~360, step: 0.1degree-NoneCellValid when [PARA]CellLocCfgType[/PARA] is set to BOTH or CELL_ANTENNAN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteEquipmentVersions earlier than RAN11.0APFlagAPFlagADD NRNCCELL(Optional)RNCAccess point(AP) cell indicator. When the indicator is TRUE, it indicates that the cell is AP cell.Enumeration TypeTRUE, FALSEFALSE,TRUENoneFALSEFALSERNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0APPApplication typeADD SCTPLNK(Mandatory)RNCUpper-layer application type of the SCTP link.At Iu-b Interface the Upper-Layer application type is NBAP,at Iu-r, Iu-PS and Iu-CS Interface the Upper-Layer application type is M3UA.Enumeration TypeNBAP, M3UANBAP, M3UANone-NoneSCTPNoneNot involvedNot involvedNot involvedThis parameter cannot be modified.Read & WriteTransportVersions earlier than RAN11.0AppliedDirectRAB applied directionADD TYPRABBASIC(Mandatory)RNCThis parameter specifies the direction where the current typical RAB parameters are applied.Enumeration TypeAPPLIED_ON_UPLINK, APPLIED_ON_DOWNLINK, APPLIED_ON_BOTHAPPLIED_ON_UPLINK, APPLIED_ON_DOWNLINK, APPLIED_ON_BOTHNone-NoneRABNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0AREAFLAGArea flagSYN BRDAREA(Optional)RNCArea flag.Enumeration TypePRIMARY(Active Area), STANDBY(Standby area), ALLPRIMARY,STANDBY,ALLNoneALLALLRNCNoneNot involvedNot involvedNot involvedThis parameter cannot be modified.Read & WriteEquipmentVersions earlier than RAN11.0AREAFLAGArea flagLOD PATCH(Optional)RNCThis parameter specifies the flag of the active and standby areas.Enumeration TypePRIMARY(Primary), STANDBY(Standby), ALLPRIMARY, STANDBY, ALLNonePrimaryPrimaryRNCWhen the value of [PARA]OT[/PARA] in [MML]LOD PATCH[/MML] Step_by_Step, the value of [PARA]AREAFLAG[/PARA] should be set.N (No impact on the UE in idle mode)Not involvedService not interrupted, but CPU will be highThis parameter cannot be modified.Read & WriteEquipmentVersions earlier than RAN11.0ARP10PriorityUser_priority of Allocation/Retention priority 10SET USERPRIORITY(Optional)RNCUser_priority corresponding to Allocation/Retention priority 10.Enumeration TypeGold, Silver, CopperGold,Silver,CopperNone-NoneRNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0ARP11PriorityUser_priority of Allocation/Retention priority 11SET USERPRIORITY(Optional)RNCUser_priority corresponding to Allocation/Retention priority 11.Enumeration TypeGold, Silver, CopperGold,Silver,CopperNone-NoneRNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0ARP12PriorityUser_priority of Allocation/Retention priority 12SET USERPRIORITY(Optional)RNCUser_priority corresponding to Allocation/Retention priority 12.Enumeration TypeGold, Silver, CopperGold,Silver,CopperNone-NoneRNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0ARP13PriorityUser_priority of Allocation/Retention priority 13SET USERPRIORITY(Optional)RNCUser_priority corresponding to Allocation/Retention priority 13.Enumeration TypeGold, Silver, CopperGold,Silver,CopperNone-NoneRNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0ARP14PriorityUser_priority of Allocation/Retention priority 14SET USERPRIORITY(Optional)RNCUser_priority corresponding to Allocation/Retention priority 14.Enumeration TypeGold, Silver, CopperGold,Silver,CopperNone-NoneRNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0ARP1PriorityUser_priority of Allocation/Retention priority 1SET USERPRIORITY(Optional)RNCUser_priority corresponding to Allocation/Retention priority 1.Enumeration TypeGold, Silver, CopperGold,Silver,CopperNone-NoneRNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0ARP2PriorityUser_priority of Allocation/Retention priority 2SET USERPRIORITY(Optional)RNCUser_priority corresponding to Allocation/Retention priority 2.Enumeration TypeGold, Silver, CopperGold,Silver,CopperNone-NoneRNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0ARP3PriorityUser_priority of Allocation/Retention priority 3SET USERPRIORITY(Optional)RNCUser_priority corresponding to Allocation/Retention priority 3.Enumeration TypeGold, Silver, CopperGold,Silver,CopperNone-NoneRNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0ARP4PriorityUser_priority of Allocation/Retention priority 4SET USERPRIORITY(Optional)RNCUser_priority corresponding to Allocation/Retention priority 4.Enumeration TypeGold, Silver, CopperGold,Silver,CopperNone-NoneRNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0ARP5PriorityUser_priority of Allocation/Retention priority 5SET USERPRIORITY(Optional)RNCUser_priority corresponding to Allocation/Retention priority 5.Enumeration TypeGold, Silver, CopperGold,Silver,CopperNone-NoneRNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0ARP6PriorityUser_priority of Allocation/Retention priority 6SET USERPRIORITY(Optional)RNCUser_priority corresponding to Allocation/Retention priority 6.Enumeration TypeGold, Silver, CopperGold,Silver,CopperNone-NoneRNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0ARP7PriorityUser_priority of Allocation/Retention priority 7SET USERPRIORITY(Optional)RNCUser_priority corresponding to Allocation/Retention priority 7.Enumeration TypeGold, Silver, CopperGold,Silver,CopperNone-NoneRNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0ARP8PriorityUser_priority of Allocation/Retention priority 8SET USERPRIORITY(Optional)RNCUser_priority corresponding to Allocation/Retention priority 8.Enumeration TypeGold, Silver, CopperGold,Silver,CopperNone-NoneRNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0ARP9PriorityUser_priority of Allocation/Retention priority 9SET USERPRIORITY(Optional)RNCUser_priority corresponding to Allocation/Retention priority 9.Enumeration TypeGold, Silver, CopperGold,Silver,CopperNone-NoneRNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0ARPRETRYARP packet resend timesSTR IPCHK(Optional)RNCThis parameter specifies the number of times the ARP resends after the specified time exceeds. Assume that "ARP packet resend times" is set to N. If the number of times no response is received after the ARP is resent for N times, the L3 DETECT FAIL alarm is reported. In the case of a key detect, the switchover of ports may be triggered.Interval Type3~103 to 10None33Ethernet PortWhen the value of [PARA]CHKTYPE[/PARA] in [MML]STR IPCHK[/MML] is set to ARP, the ARP packet resend times should be set.YThe service on the Ethernet Port.Interrupt the service until the correct gateway is set or the port swapping or the changing of IP route is finished.In order to modify this parameter, you must use the command [MML]STP IPCHK[/MML] first and [MML]STR IPCHK[/MML] next.Read & WriteTransportRAN11.0ARPTIMEOUTARP packet time-outSTR IPCHK(Optional)RNCThis parameter specifies the time-out value for the ARP packets.Interval Type3~10300 to 1000ms33Ethernet PortWhen the value of [PARA]CHKTYPE[/PARA] in [MML]STR IPCHK[/MML] is set to ARP, the ARP packet out-time should be set.Not involvedNot involvedNot involvedIn order to modify this parameter, you must use the command [MML]STP IPCHK[/MML] first and [MML]STR IPCHK[/MML] next.Read & WriteTransportRAN11.0ATMLOGICPORTThe ATM Logic Port NumberSTR NODEBBWRPT(Mandatory)RNCThis parameter specifies the number of an ATM logical port.Interval Type0~2550 to 255None-NoneNodeBNoneNot involvedNot involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteEquipmentRAN11.0ATMSNNodeB ATM_TRANS Slot No.ADD NODEBIP(Mandatory)RNCThis parameter specifies the number of the slot bearing NodeB ATM transport.Interval Type14~2714 to 27None-NoneRNCWhen the value of [PARA]NBTRANTP[/PARA] in [MML]ADD NODEBIP[/MML] is set to ATMTRANS_IP or ATMANDIPTRANS_IP, this parameter should be set.N (No impact on the UE in idle mode)Not involvedNot involvedIf the transport type of the NodeB is IUB-IP, the next hop IP address must be one of the following configured addresses: PPP link peer IP address, MLPPP group peer IP address, and the IP address in the same network segment as that of the FE/GE port.Read & WriteEquipmentVersions earlier than RAN11.0ATMSRNNodeB ATM_TRANS Subrack No.ADD NODEBIP(Mandatory)RNCThis parameter specifies the number of the subrack bearing NodeB ATM transport.Interval Type0~50 to 5None-NoneRNCWhen the value of [PARA]NBTRANTP[/PARA] in [MML]ADD NODEBIP[/MML] is set to ATMTRANS_IP or ATMANDIPTRANS_IP, this parameter should be set.N (No impact on the UE in idle mode)Not involvedNot involvedIf the transport type of the NodeB is IUB-IP, the next hop IP address must be one of the following configured addresses: PPP link peer IP address, MLPPP group peer IP address, and the IP address in the same network segment as that of the FE/GE port.Read & WriteEquipmentVersions earlier than RAN11.0ATTAttach/detach indicationADD CNDOMAIN(Optional)RNCIndicating whether attach/detach is allowed. NOT_ALLOWED indicates that MS cannot apply the IMSI attach/detach procedure. ALLOWED indicates that MS can apply the IMSI attach/detach procedure. It is valid only when [CN domain ID] is set as CS_DOMAIN.Enumeration TypeNOT_ALLOWED, ALLOWEDNOT_ALLOWED,ALLOWEDNoneALLOWEDALLOWEDRNCATT needs to be set when [PARA]CNDomainId[/PARA] in [MML]ADD CNDOMAIN[/MML] is set to CS_DOMAIN; ATT does not need to be set when [PARA]CNDomainId[/PARA] in [MML]ADD CNDOMAIN[/MML] is set to PS_DOMAIN.N (For the UE in idle mode, indicating whether the MS can apply the IMSI attach/detach procedure)Not involvedNot involvedThe modification of ATT is valid only when [PARA]CNDomainId[/PARA] in [MML]ADD CNDOMAIN[/MML] is set to CS_DOMAIN.The parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0AUTHMODEValidate modeADD PPPLNK(Mandatory) ADD MPGRP(Mandatory)RNCThis parameter specifies the authentication mode during PPP or MLPPP link negotiation.Enumeration TypeSERVER, CLIENTSERVER(sever mode), CLIENT(client mode)None-NonePPP Link(ADD PPPLNK) MLPPP Group, PPP Link(ADD MPGRP)When the value of [PARA]AUTHTYPE[/PARA] in [MML]ADD PPPLNK[/MML] is set to PAP_V or CHAP_V, the AUTHMODE should be set.YPPP linkInterrupt the service until negotiate successfully again.The negotiation will be successful only when the parameter is set the same with the local and peer device.Read & WriteTransportVersions earlier than RAN11.0AUTHNAMEValidate user nameADD PPPLNK(Mandatory) ADD MPGRP(Mandatory)RNCThis parameter specifies the user name for PPP or MLPPP link negotiation.String Type-0 to 63 characterNone-NonePPP Link(ADD PPPLNK) MLPPP Group, PPP Link(ADD MPGRP)NoneYPPP linkInterrupt the service until negotiate successfully again.The negotiation will be successful only when the parameter is set the same with the local and peer device.Read & WriteTransportVersions earlier than RAN11.0AUTHPWDValidate passwordADD PPPLNK(Mandatory) ADD MPGRP(Mandatory)RNCThis parameter specifies the password for PPP or MLPPP link negotiation.String Type-0 to 15 characterNone-NonePPP Link(ADD PPPLNK) MLPPP Group, PPP Link(ADD MPGRP)NoneYPPP linkInterrupt the service until negotiate successfully again.The negotiation will be successful only when the parameter is set the same with the local and peer device.Read & WriteTransportRAN11.0AUTHTYPEValidate protocol typeADD PPPLNK(Optional) ADD MPGRP(Optional)RNCThis parameter specifies the authentication protocol type during PPP or MLPPP link negotiation.Enumeration TypeNO_V, PAP_V, CHAP_VNO_V(not verify), PAP_V(PAP verify), CHAP_V(CHAP verify)NoneNO_VNO_VPPP Link(ADD PPPLNK) MLPPP Group, PPP Link(ADD MPGRP)NoneNot involvedNot involvedNot involvedThe negotiation will be successful only when the parameter is set the same with the local and peer device.Read & WriteTransportVersions earlier than RAN11.0AUTOAuto negotiationSET ETHPORT(Optional)RNCThis parameter specifies whether the auto negotiation is enabled.1. The auto negotiation must be enabled when "Board type " is set to FG2a, and "Port type" is set to GE.2. If the auto negotiation is enabled, the transmission rate over the FE port, work mode, and flow control mode depend on the negotiation results. If the auto negotiation not disabled, you can set the transmission rate over the FE port, work mode, and flow control mode. In this case, ensure that the settings are the same as those of the peer end; otherwise, transport failure may occur.3. If the auto negotiation is enabled at the local end, the auto negotiation must be enabled at the peer end.Enumeration TypeENABLE, DISABLEENABLE, DISABLENone-ENABLEEthernet portWhen the value of [PARA]PTYPE[/PARA] in [MML]SET ETHPORT[/MML] is set to FE,the self-confer parameter is valid.YPortIf the mode is not consistent, will interrupt service until it is consistent.The modification may affect the state of the port, may interrupt service temply. If the modification is not consistent, service may be interrupted.Read & WriteTransportVersions earlier than RAN11.0AvailablesignatureEndIndexAvailable signature end indexADD PRACHASC(Optional)RNCIdentifying the available signature end index of an ASC. For detailed information of this parameter, refer to 3GPP TS 25.304.Interval Type0~150~15None77Physical channel[PARA]AvailablesignatureEndIndex[/PARA] should be less than the number of preamble signatures. The preamble signature is configured by [PARA]PreambleSignatures[/PARA].N (Impact on random access for UEs in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0AvailablesignatureStartIndexAvailable signature start indexADD PRACHASC(Optional)RNCIdentifying the available signature start index of an ASC. For detailed information of this parameter, refer to 3GPP TS 25.304.Interval Type0~150~15None00Physical channel[PARA]AvailablesignatureStartIndex[/PARA] should be no greater than [PARA] AvailablesignatureEndIndex [/PARA].N (Impact on random access for UEs in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0AvailableSubchannelCtrlWordAvailable subchannel control wordADD PRACHASC(Optional)RNCIdentifying the available sub channels of an ASC. When a UE has been accessed to a sub channel, if [AICH transmission timing] is set to 1 (using the command ADD AICH), the 4 bits of this parameter will be repeated 3 times to form a Bitstring (12). Then, it is put into an "and " calculation together with the Bitstring (12) corresponding to the available sub channel allocated to the PRACH, and a 12-bit data stream is obtained finally. If a bit is 1, the corresponding sub channel is available for this ASC. If [AICH transmission timing] is set to 0, the lowest 3 bits of this parameter will be repeated 4 times to form a Bitstring (12). Then, it is put into an "and" calculation together with the Bitstring (12) corresponding to the available sub channel allocated to the PRACH, and a 12-bit data stream is obtained finally. If a bit is 1, the corresponding sub channel is available for this ASC. For detailed information of this parameter, refer to 3GPP TS 25.304.Interval Type0~150~15None1515Physical channelNoneN (Impact on random access for UEs in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0AvailCapCapability of CN NodeADD CNNODE(Mandatory)RNCThe Capability of CN node.Interval Type0~655350~65535000 step:1000None-NoneRNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteEquipmentVersions earlier than RAN11.0AVOLAlarm VOL.SET ALMPORT(Optional)RNCThis parameter specifies the alarm level.Enumeration TypeLOW(Low), HIGH(High)LOW,HIGHNone-NoneSRBNoneNot involvedNot involvedNot involvedThis parameter cannot be modified.Read & WriteEquipmentRAN11.0BACK8KCLKSW1Output Switch of backplane 8K OutClock 1SET CLK(Optional)RNCThis parameter specified the output switch of 8 kHz output clock 1.Enumeration TypeOFF, ONOFF, ONNone-NonesubrackWhen the value of [PARA]SRT[/PARA] in [MML]SET CLK[/MML] is set to RSS, the value of [PARA]BACK8KCLKSW1[/PARA] could be set.YRNCLess than 5 minutesEach 8 kHz clock of the backplane corresponds to only one clock source. The same 8 kHz clock switch of the backplane cannot be turned on for multiple interface boards at the same time.Read & WriteEquipmentVersions earlier than RAN11.0BACK8KCLKSW2Output Switch of backplane 8K OutClock 2SET CLK(Optional)RNCThis parameter specified the output switch of 8 kHz output clock 2.Enumeration TypeOFF, ONOFF, ONNone-NonesubrackWhen the value of [PARA]SRT[/PARA] in [MML]SET CLK[/MML] is set to RSS, the value of [PARA]BACK8KCLKSW2[/PARA] could be set.YRNCLess than 5 minutesEach 8 kHz clock of the backplane corresponds to only one clock source. The same 8 kHz clock switch of the backplane cannot be turned on for multiple interface boards at the same time.Read & WriteEquipmentVersions earlier than RAN11.0BackgroundNoiseBackground noiseADD CELLCAC(Optional)RNCIf [Auto-Adaptive Background Noise Update Switch] is set to OFF, it is used to set background noise of the cell. If [Auto-Adaptive Background Noise Update Switch] is set to ON, new background noise is restricted by this parameter and [PARA]BgnAbnormalThd[/PARA]. For detailed information of this parameter, refer to the 3GPP TS 25.133.Interval Type0~621-112~-50,step:0.1dBm6161CellNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0BACKUPPATHPath of Backup FileBKP DB(Optional)RNCThis parameter specifies the full path for saving the backup file. If the specified path is not a full path, then it will be treated as the relative path under "installation path in the BAM active workspace\BACKUP\".String Type-0 to 128 charactersNone-NoneRNCNoneNot involvedNot involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteEquipmentVersions earlier than RAN11.0BAKIPBackup port IP addressSTR IPCHK(Optional)RNCThis parameter specifies the IP address of the standby port.IP Address Type-0.0.0.0~255.255.255.255None-NoneEthernet portWhen the value of [PARA]MODE[/PARA] in [MML]STR IPCHK[/MML] is set to STANDBY, the backup port IP address should be set.Not involvedNot involvedNot involvedIn order to modify this parameter, you must use the command [MML]STP IPCHK[/MML] first and [MML]STR IPCHK[/MML] next.Read & WriteTransportRAN11.0BAKMASKBackup port maskSTR IPCHK(Optional)RNCThis parameter specifies the mask of the standby port.IP Address Type-0.0.0.0~255.255.255.255None-NoneEthernet portWhen the value of [PARA]MODE[/PARA] in [MML]STR IPCHK[/MML] is set to STANDBY, the backup port mask should be set.Not involvedNot involvedNot involvedIn order to modify this parameter, you must use the command [MML]STP IPCHK[/MML] first and [MML]STR IPCHK[/MML] next.Read & WriteTransportRAN11.0BAMIPBAM External Network Virtual IPADD EMSIP(Optional)RNCThis parameter specifies the virtual IP address for the BAM external network.IP Address Type-0.0.0.0~255.255.255.255None-NoneRNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThis parameter cannot be modified.Read & WriteEquipmentVersions earlier than RAN11.0BAMMASKBAM External Network MaskADD EMSIP(Optional)RNCThis parameter specifies the subnet mask of the BAM external network.IP Address Type-0.0.0.0~255.255.255.255None-NoneRNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThis parameter cannot be modified.Read & WriteEquipmentVersions earlier than RAN11.0BandIndBand indicatorADD CELLSETUP(Mandatory) ADD QUICKCELLSETUP(Mandatory) ADD GSMCELL(Optional) ADD NRNCCELL(Mandatory)RNCIndicating the selected frequency Band in the cell setup process. For detailed information of this parameter, refer to 3GPP TS 25.433.Enumeration TypeBand1, Band2, Band3, Band4, Band5, Band6, Band7, Band8, Band9, BandIndNotUsedBand1, Band2, Band3, Band4, Band5, Band6, Band7, Band8, Band9, BandIndNotUsedNone-(ADD NRNCCELL,ADD QUICKCELLSETUP,ADD CELLSETUP) GSM900_DCS1800_BAND_USED(ADD GSMCELL)None(ADD NRNCCELL,ADD QUICKCELLSETUP,ADD CELLSETUP) GSM900_DCS1800_BAND_USED(ADD GSMCELL)CellNoneYCellThe services are interrupted until the cell is activated again.The cell should be deactivated in advance.Read & WriteRadioVersions earlier than RAN11.0BandWidthForFACHBandwidth of FachSET FACHBANDWIDTH(Optional)RNCThis parameter specifies the maximum available bandwidth for each traffic class in the Cell_FACH state with the downlink HSDSCH in use. If the actual data flow exceeds the maximum bandwidth, the traffic is buffered so that the buffer occupancy is increased. As a result, the state transition from Cell-FACH to DCH occurs. This parameter should be set according to the traffic class.Interval Type1~10001~1000kbit/s-CONVERSATIONAL:7; STREAMING:8; INTERACTIVE,BACKGROUND:64RNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0BCCBS color codeADD GSMCELL(Mandatory)RNCUniquely identifying a neighboring base station with the same carrier.Interval Type0~70~7None-NoneCellNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0BcchArfcnInter-RAT cell frequency numberADD GSMCELL(Mandatory)RNCIdentifying BCCH frequency number of the inter-RAT cell.BCCH: Broadcast Control ChannelGSM1900Frequency number: (511-811)GSM1800Frequency number: (511-866)GSM900Frequency number: (0-125) or (954-1024)GSM850Frequency number: (127-252)GSM450Frequency number: (258-294)GSM480Frequency number: (305-341)Interval Type0~10230~1023None-NoneCellNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0BcchHspdschPowerBCCH HS-PDSCH powerADD CELLEFACH(Optional)RNCThis parameter specifies the transmission power of the HS-PDSCH that sends the data carried on the BCCH. When UE receive data from the HS-PDSCH in Enhanced CELL_FACH state, the data on the BCCH is also sent on the HS-PDSCH.Interval Type-350~150-35~15,step:0.1dB00CellNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0BcchHsscchPowerBCCH HS-SCCH powerADD CELLEFACH(Optional)RNCWhen UE is in Enhanced CELL_FACH state, the data on the BCCH is also sent on the HS-PDSCH. Meanwhile, the HS-SCCH shall send signaling related to HS-PDSCH. This parameter specifies the transmission power of the HS-SCCH at the time.Interval Type-350~150-35~15,step:0.1dB-30-30CellNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0BCHPowerBCH transmit powerADD BCH(Optional)RNCOffset of the BCH transmit power from the PCPICH transmit power in a cell. If the value is set too small, the UEs on the cell edge cannot receive the system messages properly. This problem affects the coverage of the downlink common channel and furthermore the coverage of the cell. If the value is set too great, it causes interference to other channels, occupies the downlink transmit power, and affects the cell capacity. For detailed information of this parameter, refer to 3GPP TS 25.433 and TS 25.331.Interval Type-350~150-35~15, step: 0.1dB-20-20Transport channelNoneN (Impact on cell system message receiving of UEs in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0BearTypeBear TypeSET USERGBR(Mandatory)RNCThis parameter specifies the bearer type of the service.- R99: The service is carried on a non-HSPA channel.- HSPA: The service is carried on an HSPA channel.Enumeration TypeR99, HSPAR99, HSPANone-NoneRNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0BEARTYPEDSP bear typeADD N7DPC(Mandatory)RNCIndicating the bear type of the DSP is MTP3 or M3UA.Enumeration TypeMTP3, M3UAMTP3, M3UANone-NoneRNCNoneNot involvedNot involvedNot involvedThis parameter cannot be modified.Read & WriteTransportVersions earlier than RAN11.0BeatDectThredHeatBeat Lost Times ThresholdADD RNCPOOL(Optional)RNCHeatBeat Sending Time Interval.Interval Type1~105None55RNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0BeatRecvrThredHeatBeat Recover Times ThresholdADD RNCPOOL(Optional)RNCHeatBeat Sending Time Interval.Interval Type1~102None22RNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0BeatSendingDisHeatBeat Sending Time IntervalADD RNCPOOL(Optional)RNCHeatBeat Sending Time Interval.Interval Type1~601~60s11RNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0BeBitRateThdBE service handover rate thresholdSET HOCOMM(Optional)RNCThe bit rate threshold used to determine whether to perform soft handover for the Best Effort (BE) service on DCH. If current DL DCH bit rates of all the BE services of a user are lower than or equal to this threshold, the system will perform soft handover for this user to guarantee the service quality. When the velocity of the downlink DCH exceeds the restriction of this parameter, RNC will perform intra-frequence hard handover. To avoid the great effect of the system capacity when multi-links transmit a great deal of the same data in the macro diversity.Enumeration TypeD8, D16, D32, D64, D128, D144, D256, D3848, 16, 32, 64, 128, 144, 256, 384kbit/s-D384RNCNoneN (No impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0BeCpc2EFachStateTransTimerBE CPC to E_FACH Transition TimerSET UESTATETRANSTIMER(Optional)RNCTimer for state transition from CPC_HS-DSCH to E_FACH of BE services, used to detect whether a BE UE in CELL_DCH(with CPC_HS-DSCH) state is in stable low activity state. The too small parameter cannot probably confirm that a UE is in relatively stable low activity state, but the too big will waste the dedicated channel resource. This parameter should be set based on the BE service model.Interval Type1~655351~65535s-5RNCNoneN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0BeCpc2FStateTransTimerBE CPC to FACH Transition TimerSET UESTATETRANSTIMER(Optional)RNCTimer for state transition from CPC_HS-DSCH to FACH of BE services, used to detect whether a BE UE in CELL_DCH(with CPC_HS-DSCH) state is in stable low activity state. The too small parameter cannot probably confirm that a UE is in relatively stable low activity state, but the too big will waste the dedicated channel resource. This parameter should be set based on the BE service model.Interval Type1~655351~65535s-5RNCNoneN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0BeD2EFachStateTransTimerBE DCH to E_FACH Transition TimerSET UESTATETRANSTIMER(Optional)RNCTimer for state transition from DCH to E_FACH of BE services, used to detect whether a BE UE in CELL_DCH(with DCH) state is in stable low activity state. The too small parameter cannot probably confirm that a UE is in relatively stable low activity state, but the too big will waste the dedicated channel resource. This parameter should be set based on the BE service model.Interval Type1~655351~65535s-5RNCNoneN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0BeD2FStateTransTimerBE DCH to FACH Transition TimerSET UESTATETRANSTIMER(Optional)RNCTimer for state transition from DCH to FACH of BE services, used to check whether the UE in the CELL_DCH state with non-real-time services is in the stable low activity state. If the value of this parameter is too low, whether the UE is in the stable low activity state cannot be determined. If the value of this parameter is too high, the dedicated channel resources are wasted. This parameter should be set on the basis of the BE service model.Interval Type1~655351~65535s-5RNCNoneN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0BeDlAct1First Action For BE Downlink QOSSET QOSACT(Optional)RNCThe first action selected by the QoS control algorithm when the DL QoS of BE service deteriorates.If QoS action is RateDegrade, then the rate will be downsized to the full coverage rate according to 3-rates rule.Enumeration TypeNone, RateDegrade, InterFreqHO, InterRatHONone, RateDegrade, InterFreqHO, InterRatHONone-RateDegradeRNCValid when [PARA]BEQosPerform[/PARA] is set to YES;[PARA]BeDlAct2[/PARA] and [PARA]BeDlAct3[/PARA] must be None when [PARA]BeDlAct1[/PARA] is set to None;[PARA]BeDlAct2[/PARA] and [PARA]BeDlAct3[/PARA] must not be equal with [PARA]BeDlAct1[/PARA] when [PARA]BeDlAct1[/PARA] is not set to None;N (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0BeDlAct2Second Action For BE Downlink QOSSET QOSACT(Optional)RNCThe second action selected by the QoS control algorithm when the DL QoS of BE service deteriorates.If QoS action is RateDegrade, then the rate will be downsized to the full coverage rate according to 3-rates rule.Enumeration TypeNone, RateDegrade, InterFreqHO, InterRatHONone, RateDegrade, InterFreqHO, InterRatHONone-NoneRNCValid when [PARA]BEQosPerform[/PARA] is set to YES;[PARA]BeDlAct2[/PARA] must be None when [PARA]BeDlAct1[/PARA] is set to None;[PARA]BeDlAct2[/PARA] must not be equal with [PARA]BeDlAct1[/PARA] when [PARA]BeDlAct1[/PARA] is not set to None;[PARA]BeDlAct3[/PARA] must be None when [PARA]BeDlAct2[/PARA] is set to None;[PARA]BeDlAct3[/PARA] must not be equal with [PARA]BeDlAct2[/PARA] and [PARA]BeDlAct1[/PARA] when [PARA]BeDlAct2[/PARA] is not set to NoneN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0BeDlAct3Third Action For BE Downlink QOSSET QOSACT(Optional)RNCThe third action selected by the QoS control algorithm when the DL QoS of BE service deteriorates.If QoS action is RateDegrade, then the rate will be downsized to the full coverage rate according to 3-rates rule.Enumeration TypeNone, RateDegrade, InterFreqHO, InterRatHONone, RateDegrade, InterFreqHO, InterRatHONone-NoneRNCValid when [PARA]BEQosPerform[/PARA] is set to YES;[PARA]BeDlAct3[/PARA] must be None when [PARA]BeDlAct1[/PARA] or [PARA]BeDlAct2[/PARA] is set to None;[PARA]BeDlAct3[/PARA] must not be equal with [PARA]BeDlAct1[/PARA] when [PARA]BeDlAct1[/PARA] is not set to None[PARA]BeDlAct3[/PARA] must not be equal with [PARA]BeDlAct2[/PARA] when [PARA]BeDlAct2[/PARA] is not set to NoneN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0BeE2FStateTransTimerBE E-DCH To FACH State Transition TimerSET UESTATETRANSTIMER(Optional)RNCTimer for state transition from E-DCH to FACH of BE services, used to check whether the UE with BE services carried over the E-DCH is in the stable low activity state. If the value of this parameter is too low, whether the UE is in the stable low activity state cannot be determined. If the value of this parameter is too high, the dedicated channel resources are wasted. This parameter should be set on the basis of the BE service model.Interval Type1~655351~65535s-5RNCNoneN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0BeEFach2CpcTvmThdBE E_FACH2CPC 4A ThresholdSET UESTATETRANS(Optional)RNCThis parameter specifies the threshold of the traffic volume of 4A event for triggering the transition of BE services from E_FACH to CPC. If the value of this parameter is too high, congestion may occur over the common channel.Enumeration TypeD16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k, D32k, D48k, D64k, D96k, D128k, D192k, D256k, D384k, D512k, D768k16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768kbyte-D1024RNCThe following relationship must be satisfied:[PARA]BeH2FTvmThd[/PARA] < [PARA]BeEFach2CpcTvmThd[/PARA].N (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0BeEFach2CpcTvmTimeToTrigBE E_FACH2CPC 4A TimeSET UESTATETRANS(Optional)RNCThis parameter specifies the occurrence time of 4A event for triggering the transition of BE services from E_FACH to CPC. This parameter prevents unnecessary reports that are caused by traffic volume instability from being triggered. If the value of this parameter is too high, the period of reporting 4A event is delayed and congestion may occur over the common channel.Enumeration TypeD0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640, D1280, D2560, D50000, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280, 2560, 5000ms-D0RNCNoneN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0BeEFach2DTvmThdBE E_FACH2D 4A ThresholdSET UESTATETRANS(Optional)RNCThis parameter specifies the threshold of the traffic volume of 4A event for triggering the transition of BE services from E_FACH to DCH. If the value of this parameter is too high, congestion may occur over the common channel.Enumeration TypeD16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k, D32k, D48k, D64k, D96k, D128k, D192k, D256k, D384k, D512k, D768k16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768kbyte-D1024RNCThe following relationship must be satisfied:[PARA]D2F2PTvmThd[/PARA] < [PARA]BeEFach2DTvmThd[/PARA].N (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0BeEFach2DTvmTimeToTrigBE E_FACH2D 4A TimeSET UESTATETRANS(Optional)RNCThis parameter specifies the occurrence time of 4A event for triggering the transition of BE services from E_FACH to DCH. This parameter prevents unnecessary reports that are caused by traffic volume instability from being triggered. If the value of this parameter is too high, the period of reporting 4A event is delayed and congestion may occur over the common channel.Enumeration TypeD0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640, D1280, D2560, D50000, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280, 2560, 5000ms-D0RNCNoneN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0BeEFach2HTvmThdBE E_FACH2HS-DSCH 4A ThresholdSET UESTATETRANS(Optional)RNCThis parameter specifies the threshold of the traffic volume of 4A event for triggering the transition of BE services from E_FACH to HS-DSCH. If the value of this parameter is too high, congestion may occur over the common channel.Enumeration TypeD16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k, D32k, D48k, D64k, D96k, D128k, D192k, D256k, D384k, D512k, D768k16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768kbyte-D1024RNCThe following relationship must be satisfied:[PARA]BeH2FTvmThd[/PARA] < [PARA]BeEFach2HTvmThd[/PARA].N (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0BeEFach2HTvmTimeToTrigBE E_FACH2HS-DSCH 4A TimeSET UESTATETRANS(Optional)RNCThis parameter specifies the occurrence time of 4A event for triggering the transition of BE services from E_FACH to HS-DSCH. This parameter prevents unnecessary reports that are caused by traffic volume instability from being triggered. If the value of this parameter is too high, the period of reporting 4A event is delayed and congestion may occur over the common channel.Enumeration TypeD0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640, D1280, D2560, D50000, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280, 2560, 5000ms-D0RNCNoneN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0BeF2CpcETvmThdBE F2CPC_E-DCH 4A ThresholdSET UESTATETRANS(Optional)RNCThis parameter specifies the threshold of the traffic volume of 4A event for triggering the transition of BE services from FACH to E-DCH with CPC technology. If the value of this parameter is too high, congestion may occur over the common channel.Enumeration TypeD16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k, D32k, D48k, D64k, D96k, D128k, D192k, D256k, D384k, D512k, D768k16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768kbyte-D1024RNCNoneN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0BeF2CpcETvmTimeToTrigBE FACH2CPC_E-DCH 4A TimeSET UESTATETRANS(Optional)RNCThis parameter specifies the occurrence time of 4A event for triggering the transition of BE services from FACH to E-DCH with CPC technology. This parameter prevents unnecessary reports that are caused by traffic volume instability from being triggered. If the value of this parameter is too high, the period of reporting 4A event is delayed and congestion may occur over the common channel.Enumeration TypeD0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640, D1280, D2560, D50000, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280, 2560, 5000ms-D0RNCNoneN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0BeF2CpcHTvmThdBE F2CPC_HS-DSCH 4A ThresholdSET UESTATETRANS(Optional)RNCThis parameter specifies the threshold of the traffic volume of 4A event for triggering the transition of BE services from FACH to HS-DSCH with CPC technology. If the value of this parameter is too high, congestion may occur over the common channel.Enumeration TypeD16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k, D32k, D48k, D64k, D96k, D128k, D192k, D256k, D384k, D512k, D768k16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768kbyte-D1024RNCThe following relationship must be satisfied:[PARA]BeH2FTvmThd[/PARA] < [PARA]BeF2CpcTvmThd[/PARA].N (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0BeF2CpcHTvmTimeToTrigBE F2CPC_HS-DSCH 4A TimeSET UESTATETRANS(Optional)RNCThis parameter specifies the occurrence time of 4A event for triggering the transition of BE services from FACH to HS-DSCH with CPC technology. This parameter prevents unnecessary reports that are caused by traffic volume instability from being triggered. If the value of this parameter is too high, the period of reporting 4A event is delayed and congestion may occur over the common channel.Enumeration TypeD0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640, D1280, D2560, D50000, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280, 2560, 5000ms-D0RNCNoneN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0BeF2DTvmThdBE F/R2D 4A ThresholdSET UESTATETRANS(Optional)RNCThis parameter specifies the threshold of the traffic volume of 4A event for triggering the transition of BE services from FACH to DCH. If the value of this parameter is too high, congestion may occur over the common channel.Enumeration TypeD16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k, D32k, D48k, D64k, D96k, D128k, D192k, D256k, D384k, D512k, D768k16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768kbyte-D1024RNCThe following relationship must be satisfied:[PARA]D2F2PTvmThd[/PARA] < [PARA]F2DTvmThd[/PARA].N (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0BeF2DTvmTimeToTrigBE F/R2D 4A TimeSET UESTATETRANS(Optional)RNCThis parameter specifies the occurrence time of 4A event for triggering the transition of BE services from FACH to DCH. This parameter prevents unnecessary reports that are caused by traffic volume instability from being triggered. If the value of this parameter is too high, the period of reporting 4A event is delayed and congestion may occur over the common channel.Enumeration TypeD0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640, D1280, D2560, D50000, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280, 2560, 5000ms-D0RNCNoneN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0BeF2ETvmThdBE F2E-DCH 4A ThresholdSET UESTATETRANS(Optional)RNCThis parameter specifies the threshold of the traffic volume of 4A event for triggering the transition of BE services from FACH to E-DCH. If the value of this parameter is too high, congestion may occur over the common channel.Enumeration TypeD16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k, D32k, D48k, D64k, D96k, D128k, D192k, D256k, D384k, D512k, D768k16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768kbyte-D1024RNCNoneN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0BeF2ETvmTimeToTrigBE F2E-DCH 4A TimeSET UESTATETRANS(Optional)RNCThis parameter specifies the occurrence time of 4A event for triggering the transition of BE services from FACH to E-DCH. This parameter prevents unnecessary reports that are caused by traffic volume instability from being triggered. If the value of this parameter is too high, the period of reporting 4A event is delayed and congestion may occur over the common channel.Enumeration TypeD0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640, D1280, D2560, D50000, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280, 2560, 5000ms-D0RNCNoneN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0BeF2HTvmThdBE F2HS-DSCH 4A ThresholdSET UESTATETRANS(Optional)RNCThis parameter specifies the threshold of the traffic volume of 4A event for triggering the transition of BE services from FACH to HS-DSCH. If the value of this parameter is too high, congestion may occur over the common channel.Enumeration TypeD16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k, D32k, D48k, D64k, D96k, D128k, D192k, D256k, D384k, D512k, D768k16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768kbyte-D1024RNCThe following relationship must be satisfied:[PARA]BeH2FTvmThd[/PARA] < [PARA]BeF2HTvmThd[/PARA].N (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0BeF2HTvmTimeToTrigBE F2HS-DSCH 4A TimeSET UESTATETRANS(Optional)RNCThis parameter specifies the occurrence time of 4A event for triggering the transition of BE services from FACH to HS-DSCH. This parameter prevents unnecessary reports that are caused by traffic volume instability from being triggered. If the value of this parameter is too high, the period of reporting 4A event is delayed and congestion may occur over the common channel.Enumeration TypeD0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640, D1280, D2560, D50000, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280, 2560, 5000ms-D0RNCNoneN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0BeF2PStateTransTimerBE FACH to PCH Transition TimerSET UESTATETRANSTIMER(Optional)RNCTimer for state transition from FACH to PCH of BE services, used to check whether the UE in the CELL_FACH state is in the stable low activity state. When this parameter is set to 65535, it is regarded that the state transition from FACH to PCH is not performed. If the value of this parameter is too low, whether the UE is in the stable low activity state cannot be determined. If the value of this parameter is too high, the common channel resources are wasted. This parameter should be set on the basis of the BE service model.Interval Type1~655351~65535s-65535RNCNoneN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioRAN11.0BeH2EFachStateTransTimerBE HSPA to E_FACH Transition TimerSET UESTATETRANSTIMER(Optional)RNCTimer for state transition from HS-DSCH to E_FACH of BE services, used to detect whether a BE UE in CELL_DCH(with HS-DSCH) state is in stable low activity state. The too small parameter cannot probably confirm that a UE is in relatively stable low activity state, but the too big will waste the dedicated channel resource. This parameter should be set based on the BE service model.Interval Type1~655351~65535s-5RNCNoneN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0BeH2FStateTransTimerBE HS-DSCH to FACH Transition TimerSET UESTATETRANSTIMER(Optional)RNCTimer for state transition from HS-DSCH to FACH of BE services, used to check whether the UE in the CELL_DCH(with HS-DSCH) state with BE services is in the stable low activity state. If the value of this parameter is too low, whether the UE is in the stable low activity state cannot be determined. If the value of this parameter is too high, the dedicated channel resources are wasted. This parameter should be set on the basis of the BE service model.Interval Type1~655351~65535s-5RNCNoneN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0BeH2FTvmPTATBE HS-DSCH2F 4B Pending TimeSET UESTATETRANS(Optional)RNCPending time after the traffic volume event 4B is reported. This parameter is used to prevent too many traffic volume events 4B being reported.Enumeration TypeD250, D500, D1000, D2000, D4000, D8000, D16000250, 500, 1000, 2000, 4000, 8000, 16000ms-D1000RNCNoneN (no impact on the UE in idle mode)Not involvedNot involvedThe parameter modification has no impact on the equipment.Read & WriteRadioVersions earlier than RAN11.0BeH2FTvmThdBE HS-DSCH2F 4B ThresholdSET UESTATETRANS(Optional)RNCThis parameter is used to check whether the UE in the low activity state. If the UE is on HS-DSCH channel, the low activity counter increases by 1 every time traffic volume event 4B is reported.Enumeration TypeD8, D16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k, D32k, D48k, D64k, D96k, D128k, D192k, D256k, D384k, D512k, D768k8, 16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k, 24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768kbyte-D64RNCThe follow