Upload
others
View
25
Download
0
Embed Size (px)
Citation preview
AIR TECHSYSTEMS
Technical Documentation
LTG High Performance Tangential FansSeries TW
Impeller diameter from 125 to 200 mm
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 2 of 32
Content
LTG High Performance Tangential Fans-an advantage for best heating, cooling, drying, blasting 4. . . . . . . . .
Flow principle 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Advantages 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Application ofLTG High Performance Tangential Fans 4. . . . . . . . . . . . . . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 125 mm 5. . . . . . . . . . . . . . . . . . . . . . . . . .
Service conditions 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specification and design features 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delivery range series TW, impeller diameter 125 mm 5. . . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 125 mm 6. . . . . . . . . . . . . . . . . . . . . . . . . .
Position of the fan 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation and start up 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions and performance data 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 125 mm 7. . . . . . . . . . . . . . . . . . . . . . . . . .
Plug in slots 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 125mm 8. . . . . . . . . . . . . . . . . . . . . . . . . .
Fan curves for nominal length 400 mm (15.75 inch) 8. . . . . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 125 mm 9. . . . . . . . . . . . . . . . . . . . . . . . . .
Fan curves for nominal length 600 mm (23.62 inch) 9. . . . . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 125 mm 10. . . . . . . . . . . . . . . . . . . . . . . . . .
Fan curves for nominal length 800 mm(31.50 inch) 10. . . . . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 125 mm 11. . . . . . . . . . . . . . . . . . . . . . . . . .
Fan curves for nominal length 1000 mm (39.37 inch) 11. . . . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 150 mm 12. . . . . . . . . . . . . . . . . . . . . . . . . .
Service conditions 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specification and design features 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delivery Range Series TW, impeller diameter 150 mm 12. . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 150 mm 13. . . . . . . . . . . . . . . . . . . . . . . . . .
Position of the fan 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation and start up 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions and performance data 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 150 mm 14. . . . . . . . . . . . . . . . . . . . . . . . . .
Plug in slots 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 150mm 15. . . . . . . . . . . . . . . . . . . . . . . . . .
Fan curves for nominal length 401 mm (15.79 inch) 15. . . . . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 150 mm 16. . . . . . . . . . . . . . . . . . . . . . . . . .
Fan curves for nominal length 601 mm (23.66 inch) 16. . . . . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 150 mm 17. . . . . . . . . . . . . . . . . . . . . . . . . .
Fan curves for nominal length 864 mm (34.02 inch) 17. . . . . . . . . . . . . . . .
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 3 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 150 mm 18. . . . . . . . . . . . . . . . . . . . . . . . . .
Fan curves for nominal length 1064 mm (41.89 inch) 18. . . . . . . . . . . . . . .
Test conditions for the fan curves 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 150 mm 19. . . . . . . . . . . . . . . . . . . . . . . . . .
Fan curves for nominal length 1264 mm (49.76 inch) 19. . . . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 150 mm 20. . . . . . . . . . . . . . . . . . . . . . . . . .
Fan curves for nominal length 1464 mm (49.76 inch) 20. . . . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 200 mm 21. . . . . . . . . . . . . . . . . . . . . . . . . .
Service conditions 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specification and design features 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delivery range series TW impeller diameter 200 mm 21. . . . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 200 mm 22. . . . . . . . . . . . . . . . . . . . . . . . . .
Position of the fan 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation and start up 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions and performance data 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LTG LTG High Performance Tangential FansSeries TW, impeller diameter 200 mm 23. . . . . . . . . . . . . . . . . . . . . . . . . .
Plug in slots 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 200 mm 24. . . . . . . . . . . . . . . . . . . . . . . . . .
Fan curves for nominal length 400 mm (15.75 inch) 24. . . . . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 200 mm 25. . . . . . . . . . . . . . . . . . . . . . . . . .
Fan curves for nominal length 630 mm (24.8 inch) 25. . . . . . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 200 mm 26. . . . . . . . . . . . . . . . . . . . . . . . . .
Fan curves for nominal length 800 mm (31.5 inch) 26. . . . . . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 200 mm 27. . . . . . . . . . . . . . . . . . . . . . . . . .
Fan curves for nominal length 1000 mm (39.37 inch) 27. . . . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 200 mm 28. . . . . . . . . . . . . . . . . . . . . . . . . .
Fan curves for nominal length 1250 mm (49.21 inch) 28. . . . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 150 and 200 mm 29. . . . . . . . . . . . . . . . . .
Acoustical data 29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 150mm and 200 mm 30. . . . . . . . . . . . . .
Accessories and special versions 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation, initiation 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Detachment 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LTG High Performance Tangential FansSeries TW, impeller diameter 125, 150 and 200 mm 31. . . . . . . . . . . . .
Selection 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 4 of 32
LTG High Performance Tangential Fans-an advantage for best heating, cooling, drying, blastingMany production processes require an extended linearand absolutely even distribution of air or other gases overa certain area.
The special design of, High Performance Tangential Fansprovides the optimum solution for these requirements.
The robust design and the use of high quality materials as-sure a long life expectancy.
The way these fans work, allowing even air distributionwithout additional baffles and vanes, and the space-savingdesign, make the use of tangential fans very economic.
Flow principleIn a tangential fan, the air is drawn in over the entire lengthof the fan impeller. Inside the impeller, the airflow is divertedand accelerated by the vortex created by the rotation of theimpeller.
The airstream then exists over the entire length of the im-peller on the discharge side. The vortex separatesthe intake and discharge side of the fan at the narrowestpoint betwen the impeller and the vortex builder. Togetherwith the fan scroll , the vortex directs the airflow. This res-ults in an almost uniform laminar airflow over the entire out-let width of the fan.
impeller vortex inducer fan scroll
Advantages Uniform, extended airflow over large areas. Space-saving installation due to 90_ and 180° airflow
pattern. Fan length can be matched exactly to machine width. Airflow conditions remain the same even for wider ma-
chines (simplified design and drafting in case of modularsystems).
Fans perform well in any mounting position. Drive can bemounted on right or left hand side.
Quiet operation due to optimised impeller and housingdesign.
Long live expectancy due to robust design and locationof bearings outside the hot air zone.
Explosion-proof models according to ATEX available.
Application ofLTG High Performance Tangential Fans Agricultural technology air-conditioning technology apparatus engineering automotive industry bakery technology biomedical industry building material industry chemical industry cleaning technology control panel technology dedusting technology drying technology electronic industry environmental simulations food industry furnace technology heat treatment technology mechanical and plant engineering medical technology packaging industry paper industry pharmaceutical industry power plant engineering process engineering railway technology refrigeration technology store design surface technology swimming pool technology textile machinery design tobacco industry transportation cooling wood industry ...
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 5 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 125 mm
The tangential fan series TW 125 is a rigid industrial gradefan with enhanced corrosion protection and high powerdensity.
LTG Tangential Fan type TWL 125(left hand drive)
Service conditionsgas temperatures:-13 F up to +248 F (-25 C bis max. +120 C)ambient temperatures:-13 F up to +104 F (-25 C bis max. +40 C)
Specification and design featuresTangential fan with shaft end on the drive side.
Rigid bolted, corrosion proof casing of marine grade alu-minium (DIN 1725). Impeller of galvanized steel.
The impeller is both sides bedded in self-aligning ball bear-ings. Bearing design life is 25 000 hours. The counter sidebearing is mounted vibration dampened. Both bearings arelifetime lubricated.
Recommended V-belt pulley:dw = 125 mm (4.9 in), profile SPA 12,5 mm (0.49 inch), DIN7753.The maximum rated power transmission for the pulley is 4kW (5.36 hp).Intake and discharge openings have sealing planes andplug in slots to connect exactly to ducts and appliances.The complete fan (including bearing clearance etc.) is bal-anced to grade Q 6.3 according to VDI 2060.
Length tolerances acc. to ISO 2768 vL.
Delivery range series TW, impeller diameter 125 mm
typemax.
medium temperatures impeller length casing impeller
TWR 125/400/NTWL 125/400/N
-25 C to +120 C(-13 F to +248 F)
400 mm(15.75 inch)
stainless steelaluminium galvanized steel
TWR 125/600/NTWL 125/600/N
600 mm(23.62 inch)
TWR 125/800/NTWL 125/800/N
800 mm(31.50 inch)
TWR 125/1000/NTWL 125/1000/N
1000 mm(39.37 inch)
TWR = right hand driveTWL = left hand drive
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 6 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 125 mm
Position of the fanAny arrangement is possible.
Installation and start upFix the fans without any distortion to a plane base frame.For fixation of the fan use only the bolt holes provided in theside elements.
To connect to ducts and appliances plug in slots and seal-ing planes are provided over the whole fan width for the in-take and discharge openings.
Dimensions and performance data
Make sure to observe the applicable safety codes beforestarting the fans.
Check V-belt selection for higher temperature applications.
The fans are designed for continuous operation with con-stant load (operation mode S1 analogous to VDE 0530).For frequent start/stop operation please check with LTG.
Dimensions in mm
type/nominal length
dimensions airvolume
Vmax
pressureΔpfmax
speednmax
[rpm]
massesappr.
L[mm][inch]
A[mm][inch]
C[mm][inch]
[m3/h][cfm]
[Pa][” wg] [rpm]
[kg][lb]
TWR 125/400/NTWL 125/400/N
40015.75
50419.85
43617.16
39002296
5002.1
35158
17.6
TWR 125/600/NTWL 125/600/N
60023.62
70427.72
63625
48002825
2200.89
292010.5
23.15
TWR 125/800/NTWL 125/800/N
80031.5
90435.6
83632.9
37502207
1170.47
168013
28.66
TWR 125/1000/NTWL 125/1000/N
100039.37
110443.46
103640.78
38002237
800.32
139015,5
34.17
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 7 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 125 mm
Plug in slots
A B
C
D
Plug in slots over the full fan width
C
D
B
A
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 8 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 125mm
Fan curves for nominal length 400 mm (15.75 inch)The indicated shaft power consumption does not includethe loss in the belt drive
Test conditions for the fan curves
The indicated curves are valid for an air density of
ρ =0.075 lb/ft³ (1.2 kg/m3). The rating tests where done aslaboratory test according to EN ISO 5801:2008 with unre-stricted inlet and discharge. Fans with a drive power> 4.0 hp (3.0 kW) must be smoothly started.
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 9 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 125 mm
Fan curves for nominal length 600 mm (23.62 inch)The indicated shaft power consumption does not includethe loss in the belt drive
Test conditions for the fan curves
The indicated curves are valid for an air density of
ρ =0.075 lb/ft³ (1.2 kg/m3). The rating tests where done aslaboratory test according to EN ISO 5801:2008 with unre-stricted inlet and discharge. Fans with a drive power> 4.0 hp (3.0 kW) must be smoothly started.
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 10 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 125 mm
Fan curves for nominal length 800 mm(31.50 inch)The indicated shaft power consumption does not includethe loss in the belt drive
Test conditions for the fan curves
The indicated curves are valid for an air density of
ρ =0.075 lb/ft³ (1.2 kg/m3). The rating tests where done aslaboratory test according to EN ISO 5801:2008 with unre-stricted inlet and discharge. Fans with a drive power> 4.0 hp (3.0 kW) must be smoothly started.
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 11 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 125 mm
Fan curves for nominal length 1000 mm (39.37 inch)The indicated shaft power consumption does not includethe loss in the belt drive
Test conditions for the fan curves
The indicated curves are valid for an air density of
ρ =0.075 lb/ft³ (1.2 kg/m3). The rating tests where done aslaboratory test according to EN ISO 5801:2008 with unre-stricted inlet and discharge. Fans with a drive power> 4.0 hp (3.0 kW) must be smoothly started.
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 12 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 150 mm
The tangential fan series TW 150 is a rigid industrial gradefan with enhanced corrosion protection and high powerdensity.
LTG Tangential Fan type TWR 150(right hand drive)
Service conditionsgas temperatures:-13 F up to +248 F (-25 C bis max. +120 C)ambient temperatures:-13 F up to +104 F (-25 C bis max. +40 C)
Specification and design featuresTangential fan with shaft end on the drive side.
Rigid bolted, corrosion proof casing of marine grade alu-minium (DIN 1725). Impeller of galvanized steel.
The impeller is both sides bedded in self-aligning ball bear-ings. Bearing design life is 25 000 hours. The counter sidebearing is mounted vibration dampened. Both bearings arelifetime lubricated.
Recommended V-belt pulley:profile SPA 12.5 mm (0.49 inch), dw = 160 mm (6.3 inch).DIN 7753.The maximum rated power transmission for the pulley is 9kW (12 hp).Intake and discharge openings have sealing planes andplug in slots to connect exactly to ducts and appliances.The complete fan (including bearing clearance etc.) is bal-anced to grade Q 6.3 according to VDI 2060.
Length tolerances acc. to ISO 2768 vL.
Delivery Range Series TW, impeller diameter 150 mm
typemax.
medium temperatures impeller length casing impeller
TWR 150/401/NTWL 150/401/N
-25 C to +120 C(-13 F to +248 F)
401 mm(15.79 inch)
marine gradealuminium galvanized steel
TWR 150/601/NTWL 150/601/N
601 mm(23.66 inch)
TWR 150/864/NTWL 150/864/N
864 mm(34.02 inch)
TWR 150/1064/NTWL 150/1064/N
1064 mm(41.89 inch)
TWR 150/1264/NTWL 150/1264/N
1264 mm(49.76 inch)
TWR 150/1464/NTWL 150/1464/N
1464 mm(57.64 inch)
TWR = right hand driveTWL = left hand drive
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 13 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 150 mm
Position of the fanAny arrangement is possible.
Installation and start upFix the fans without any distortion to a plane base frame.For fixation of the fan use only the bolt holes provided in theside elements.
To connect to ducts and appliances plug in slots and seal-ing planes are provided over the whole fan width for the in-
take and discharge openings.
Make sure to observe the applicable safety codes beforestarting the fans.
Check V-belt selection for higher temperature applications.
The fans are designed for continuous operation with con-stant load (operation mode S1 analogous to VDE 0530):For frequent start/stop operation please check with LTG.
Dimensions and performance data
"
ø24
k6
Dimensions in mm
type/nominal length
dimensionsL A C
air-volumeVmax
pressureΔpfmax
speednmax
massesappr.
[mm][inch]
[mm][inch]
[mm][inch]
[m3/h][cfm]
[Pa][” wg] rpm
[kg][lb]
TWR 150/401/NTWL 150/401/N
40115.79
54721.54
44717.60
62003650
6002.4 2800
1022
TWR 150/601/NTWL 150/601/N
60123.66
74729.41
64725.47
88005180
6002.4 2800
1329
TWR 150/864/NTWL 150/864/N
86434.02
101039.76
91035.83
120007063
5102 2600
1636
TWR 150/1064/NTWL 150/1064/N
106441.89
121047.64
111043.70
140008240
4301.7 2400
1942
TWR 150/1264/NTWL 150/1264/N
126449.76
141055.51
131051.57
120007063
2401 1800
2249
TWR 150/1464/NTWL 150/1464/N
146457.64
161063.39
151059.45
110006475
1553.2 1440
2555
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 14 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 150 mm
Plug in slots
C
A
B
D
Plug in slots over the full fan width
C
AB
D
d Plug in slots 6 mm deepfor duct connection,
max. 1.5 mm sheet thick-ness
K slots for self-tapping screws,4.2 mm,max. 10 mm screw in depth
D slots for self-tapping screws,3.9 (3.5) mm,max. 7.5 mm screw in depth
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 15 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 150mm
Fan curves for nominal length 401 mm (15.79 inch)The indicated shaft power consumption does not includethe loss in the belt drive
Test conditions for the fan curves
The indicated curves are valid for an air density of
ρ =0.075 lb/ft³ (1.2 kg/m3). The rating tests where done aslaboratory test according to EN ISO 5801:2008 with unre-stricted inlet and discharge. Fans with a drive power> 4.0 hp (3.0 kW) must be smoothly started.
Sp
ee
d[r
pm
]
2800 = max. rated speed
Sta
ticp
ress
ure
p
f[in
chw
g]
ρ = 0.075 lb/ft³ (1.2 kg/m3)
Sta
tic
pre
ss
ure
p
f[P
a]
V [m3/h]
V [cfm]
Pd [Pa]
Pd [inch wg]
4.003.603.202.80
2.40
2.00
1.60
1.40
1.20
1.00
0.80
0.60
0.40
0.32
0.24
0.20
0.16
0.12
0.10
0.08
0.06
0.04
0.36
350
410
470
530
590
880
1180
1470
1770
2060
2350
2950
3530
4120
4710
0.06
0.08
0.12
0.16
0.24
0.32
0.40
0.60
0.80
1.20
1.60
2.40
3.20
4.00
6.00
8.00
10.00
7.4/5.54.0/3.0
2.0/1.5
1.5/1.1
1.0/0.75
0.74/0.55
0.50/0.37
0.34/0.25
0.24/0.18
0.16/0.12
0.12/0.09
1000900
700
500
250
300
350
400
600
800
200
150
100908070
60
50
40
30
20
15
10
25
600
700
800
900
1000
1500
2000
2500
3000
3500
4000
5000
6000
7000
8000
1000
1400
1600
1800
2000
2400
1200
800
15 20 30 40 60 80 100
150
200
300
400
600
800
1000
1500
2000
2500
55
4547
49
51
5354
Total efficiencyt [%]
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 16 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 150 mm
Fan curves for nominal length 601 mm (23.66 inch)The indicated shaft power consumption does not includethe loss in the belt drive
Test conditions for the fan curves
The indicated curves are valid for an air density of
ρ =0.075 lb/ft³ (1.2 kg/m3). The rating tests where done aslaboratory test according to EN ISO 5801:2008 with unre-stricted inlet and discharge. Fans with a drive power> 4.0 hp (3.0 kW) must be smoothly started.
10.0/7.55.4/4.0
4.0/3.0
3.0/2.2
1.5/1.1
1.0/0.75
0.50/0.37
0.34/0.25
0.16/0.12
0.24/0.18
Sta
ticp
ress
ure
p
f[in
chw
g]
Sta
tic
pre
ss
ure
p
f[P
a]
2800 = max rated speed
ρ = 0.075 lb/ft³ (1.2 kg/m3)
Total efficiencyt [%]
Sp
ee
d[r
pm
]
1000
1400
1600
1800
2000
2400
1200
800
0.74/0.55
58
45
49
51
5355
57
47
4.003.603.202.80
2.40
2.00
1.60
1.40
1.20
1.00
0.80
0.60
0.40
0.32
0.24
0.20
0.16
0.12
0.10
0.08
0.06
0.04
0.36
1000900
700
500
250
300
350
400
600
800
200
150
100908070
60
50
40
30
20
15
10
25
350
410
470
530
590
880
1180
1470
1770
2060
2350
2950
3530
4120
4710
600
700
800
900
1000
1500
2000
2500
3000
3500
4000
5000
6000
7000
8000 V [m3/h]
V [cfm]
Pd [Pa]
Pd [inch wg]
5300
5900
9000
10000
15 20 30 40 60 80 100
150
200
300
400
600
800
1000
1500
0.06
0.08
0.12
0.16
0.24
0.32
0.40
0.60
0.80
1.20
1.60
2.40
3.20
4.00
6.00
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 17 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 150 mm
Fan curves for nominal length 864 mm (34.02 inch)The indicated shaft power consumption does not includethe loss in the belt drive
Test conditions for the fan curves
The indicated curves are valid for an air density of
ρ =0.075 lb/ft³ (1.2 kg/m3). The rating tests where done aslaboratory test according to EN ISO 5801:2008 with unre-stricted inlet and discharge. Fans with a drive power> 4.0 hp (3.0 kW) must be smoothly started.
14.75/1110.0/7.5
7.4/5.5
4.0/3.0
3.0/2.2
2.0/1.5
1.5/1.1
1.0/0.75
0.50/0.37
0.74/0.55
0.34/0.25
0.24/0.18
Sta
ticp
ress
ureΔ
pf
[inch
wg
]
Sta
tic
pre
ss
ureΔ
pf
[Pa
]
2600 = max rated speed
ρ = 0.075 lb/ft³ (1.2 kg/m3)
Total efficiencyt [%]
1000
1400
1600
1800
2000
2300
1200
800
58
45
49
51
53
55
57
47
56
4.003.603.202.80
2.40
2.00
1.60
1.40
1.20
1.00
0.80
0.60
0.40
0.32
0.24
0.20
0.16
0.12
0.10
0.08
0.06
0.04
0.36
1000900
700
500
250
300
350
400
600
800
200
150
100908070
60
50
40
30
20
15
10
25
880
1180
1470
1770
2060
2350
2950
3530
4120
4710
1500
2000
2500
3000
3500
4000
5000
6000
7000
8000
5300
5900
9000
10000 V [m3/h]
V [cfm]
Pd [Pa]
Pd [inch wg]
590
1000
8800
15000
15 20 30 40 60 80 100
150
200
300
400
600
800
1000
1500
0.06
0.08
0.12
0.16
0.24
0.32
0.40
0.60
0.80
1.20
1.60
2.40
3.20
4.00
6.00
Sp
ee
d[r
pm
]
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 18 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 150 mm
Fan curves for nominal length 1064 mm (41.89 inch)The indicated shaft power consumption does not includethe loss in the belt drive
Test conditions for the fan curvesThe indicated curves are valid for an air density of
ρ =0.075 lb/ft³ (1.2 kg/m3). The rating tests where done aslaboratory test according to EN ISO 5801:2008 with unre-stricted inlet and discharge. Fans with a drive power> 4.0 hp (3.0 kW) must be smoothly started.
14.75/11
10.0/7.5
7.4/5.5
4.0/3.0
3.0/2.2
2.0/1.5
1.5/1.1
1.0/0.75
0.74/0.55
0.50/0.37
0.34/0.25
Sta
ticp
ress
ure
p
f[in
chw
g]
Sta
tic
pre
ss
ure
p
f[P
a]
2400 = max rated speed
ρ = 0.075 lb/ft³ (1.2 kg/m3)
Total efficiencyt [%]
Sp
ee
d[r
pm
]
1000
1400
1600
1800
2000
2200
1200
800
58
4547
49
51
53
5755
4.003.603.202.80
2.40
2.00
1.60
1.40
1.20
1.00
0.80
0.60
0.40
0.32
0.24
0.20
0.16
0.12
0.10
0.08
0.06
0.04
0.36
1000900
700
500
250
300
350
400
600
800
200
150
100908070
60
50
40
30
20
15
10
25
V [m3/h]
V [cfm]
Pd [Pa]
Pd [inch wg]
880
1180
1470
1770
2060
2350
2950
3530
4120
4710
1500
2000
2500
3000
3500
4000
5000
6000
7000
8000
5300
5900
9000
10000
8800
15000
15 20 30 40 60 80 100
150
200
300
400
600
800
1000
1500
0.06
0.08
0.12
0.16
0.24
0.32
0.40
0.60
0.80
1.20
1.60
2.40
3.20
4.00
6.00
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 19 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 150 mm
Fan curves for nominal length 1264 mm (49.76 inch)The indicated shaft power consumption does not includethe loss in the belt drive
Test conditions for the fan curves
The indicated curves are valid for an air density of
ρ =0.075 lb/ft³ (1.2 kg/m3). The rating tests where done aslaboratory test according to EN ISO 5801:2008 with unre-stricted inlet and discharge. Fans with a drive power> 4.0 hp (3.0 kW) must be smoothly started.
5.4/4.0
4.0/3.0
3.0/2.2
2.0/1.5
1.5/1.1
1.0/0.75
0.74/0.55
0.50/0.37
0.34/0.25
Sta
ticp
ress
ure
p
f[in
chw
g]
Sta
tic
pre
ss
ure
p
f[P
a]
1800 = max rated speed
r = 0.075 lb/ft³ (1.2 kg/m3)
Total efficiencyt [%]
Sp
ee
d[r
pm
]
1000
1200
1400
1600
800
58
47
49
51
53
55
57
4.003.603.202.80
2.40
2.00
1.60
1.40
1.20
1.00
0.80
0.60
0.40
0.32
0.24
0.20
0.16
0.12
0.10
0.08
0.06
0.04
0.36
1000900
700
500
250
300
350
400
600
800
200
150
100908070
60
50
40
30
20
15
10
25
V [m3/h]
V [cfm]
Pd [Pa]
Pd [inch wg]
880
1180
1470
1770
2060
2350
2950
3530
4120
4710
1500
2000
2500
3000
3500
4000
5000
6000
7000
8000
5300
5900
9000
10000
8800
15000
15 20 30 40 60 80 100
150
200
300
400
600
800
1000
0.06
0.08
0.12
0.16
0.24
0.32
0.40
0.60
0.80
1.20
1.60
2.40
3.20
4.00
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 20 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 150 mm
Fan curves for nominal length 1464 mm (49.76 inch)The indicated shaft power consumption does not includethe loss in the belt drive
Test conditions for the fan curves
The indicated curves are valid for an air density of
ρ =0.075 lb/ft³ (1.2 kg/m3). The rating tests where done aslaboratory test according to EN ISO 5801:2008 with unre-stricted inlet and discharge. Fans with a drive power> 4.0 hp (3.0 kW) must be smoothly started.
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 21 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 200 mm
The tangential fan series TW 200 is a rigid industrial gradefan with enhanced corrosion protection and high powerdensity.
LTG Tangential Fan type TWR 200(right hand drive)
Service conditionsgas temperatures:-13 F / -25 C up to +248 F / 120 Cambient temperatures:-13 F/ -25 C up to +104 F / 40 C
Specification and design featuresTangential fan with shaft end on the drive side.
Rigid bolted, corrosion proof casing of marine grade alu-minium (DIN 1725). Impeller of galvanized steel.
The impeller is both sides bedded in self-aligning ball bear-ings. Bearing design life is 25 000 hours. The counter sidebearing is mounted vibration dampened. Both bearings arelifetime lubricated.
Recommended V-belt pulley:profile SPA 12.5 mm (0.49 inch), dw = 160 mm (6.3 inch).DIN 7753.The maximum rated power transmission for the pulley is 9kW (12 hp).Intake and discharge openings have sealing planes andplug in slots to connect exactly to ducts and appliances.The complete fan (including bearing clearance etc.) is bal-anced to grade Q 6.3 according to VDI 2060.
Length tolerances acc. to ISO 2768 vL.
Delivery range series TW impeller diameter 200 mm
typemax.
medium temperatures impeller length casing impeller
TWR 200/400/NTWL 200/400/N
-25 C to +120 C(-13 F to +248 F)
400 mm(15.75 inch)
marine gradealuminium galvanized steel
TWR 200/630/NTWL 200/630/N
630 mm(24.8 inch)
TWR 200/800/NTWL 200/800/N
800 mm(31.5 inch)
TWR 200/1000/NTWL 200/1000/N
1000 mm(39.37 inch)
TWR 200/1250/NTWL 200/1250/N
1250 mm49.21 inch)
TWR = right hand driveTWL = left hand drive
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 22 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 200 mm
Position of the fanAny arrangement is possible.
Installation and start upFix the fans without any distortion to a plane base frame.For fixation of the fan use only the bolt holes provided in theside elements.
To connect to ducts and appliances sealing planes areprovided over the whole fan width for the intake and dis-charge openings.
Dimensions and performance data
Make sure to observe the applicable safety codes beforestarting the fans.
Check V-belt selection for higher temperature applications.
The fans are designed for continuous operation with con-stant load (operation mode S1 analogous to VDE 0530):For frequent start/stop operation please check with LTG.
INTAKE
DISCHARGE M6
k624
40 550
30.5
L38 38
15
86
119.5
119.5
30.5
200
50
16
125
43121
2020125
350
300
8
27
30.5144.5 144.5
30.5
5025050
15
16
38
2012
50
A
C
Dimensions in mm
type/nominal length
dimensionsL A C
air-volumeVmax
pressureΔpfmax
speednmax
massesappr.
mm[inch]
mm[inch]
mm[inch]
m3/hcfm
Pa” wg rpm
kglb
TWR 200/400/NTWL 200/400/N
40015.75
56222.13
44417.48
60003550
5502.2 2400
1636
TWR 200/630/NTWL 200/630/N
63024.8
79231.18
67426.54
80004700
4001.6 2100
2044
TWR 200/800/NTWL 200/800/N
80031.5
96237.87
84433.23
90005300
3001.2 1800
2453
TWR 200/1000/NTWL 200/1000/N
100039.37
116245.75
104441.10
100005900
2401 1600
2862
TWR 200/1250/NTWL 200/1250/N
125049.21
141255.59
129450.94
90005300
1400.6 1200
3271
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 23 of 32
LTG LTG High Performance Tangential FansSeries TW, impeller diameter 200 mm
Plug in slots
fE
A
f
Plug in slots over the full fan width
A
E
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 24 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 200 mm
Fan curves for nominal length 400 mm (15.75 inch)The indicated shaft power consumption does not includethe loss in the belt drive
Test conditions for the fan curves
The indicated curves are valid for an air density of
ρ =0.075 lb/ft³ (1.2 kg/m3). The rating tests where done aslaboratory test according to EN ISO 5801:2008 with unre-stricted inlet and discharge. Fans with a drive power> 4.0 hp(3.0 kW) must be smoothly started.
590
820
1060
1300
1530
1770
2000
2240
2470
2710
2950
3180
3400
0.08
0.12
0.16
0.20
0.24
0.28
0.32
0.36
0.80
1.20
1.60
2.00
2.40
2.80
0.08
0.12
0.16
0.20
0.24
0.28
0.32
0.36
0.40
0.80
1.20
1.60
2.00
2.40
2.80
10.2/7.5
4.0/3.0
1.5/1.1
0.50/0.37
2.0/1.5
0.34/0.25
1.0/0.75
0.74/0.55
0.24/0.18
0.16/0.12
0.12/0.09
0.60
0.40
20
30
40
50
60
70
80
90
200
300
400
500
600
700
150
100
Sta
ticp
ress
ure
p
f[in
chw
g]
Sta
tic
pre
ss
ure
p
f[P
a]
V [m3/h]
V [cfm]
Pd [Pa]
Pd [inch wg]
2400 = max rated speed
r = 0.075 lb/ft³ (1.2 kg/m3)
1800
1600
1400
1200
2200
2000
1000
600
800
5.5/4.0
1000
1400
1800
2200
2600
3000
3400
3800
4200
4600
5000
5400
5800
6200
6600
7000
20 30 40 50 60 70 80 90 100
200
300
400
500
600
700
800
900
3650
3885
4120
3.20
3.60
Totalefficiencyt [%]
Sp
ee
d[r
pm
]
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 25 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 200 mm
Fan curves for nominal length 630 mm (24.8 inch)The indicated shaft power consumption does not includethe loss in the belt drive
Test conditions for the fan curves
The indicated curves are valid for an air density of
ρ =0.075 lb/ft³ (1.2 kg/m3). The rating tests where done aslaboratory test according to EN ISO 5801:2008 with unre-stricted inlet and discharge. Fans with a drive power> 4.2 hp(3.0 kW) must be smoothly started.
1.5/1.1
0.50/0.37
2.0/1.5
1.0/0.75
0.74/0.55
2100 = max rated speed
Sta
ticp
ress
ure
p
f[in
chw
g]
Sta
tic
pre
ss
ure
p
f[P
a]
V [m3/h]
V [cfm]
Pd [Pa]
Pd [inch wg]
ρ = 0.075 lb/ft³ (1.2 kg/m3)
20
30
40
50
60
70
80
90
200
300
400
500
600
700
150
100
0.08
0.12
0.16
0.20
0.24
0.28
0.32
0.36
0.80
1.20
1.60
2.00
2.40
2.80
0.60
0.40
0.08
0.12
0.16
0.20
0.24
0.28
0.32
0.36
0.40
0.80
1.20
1.60
2.00
2.40
5.5/4.0
4.0/3.0
0.34/0.25
0.24/0.18
0.16/0.12
0.12/0.09
10.2/7.5
1500
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
6500
7000
7500
8000
8500
9000
9500
10000
20 30 40 50 60 70 80 90 100
200
300
400
500
600
700
800
1000
1200
1400
2000
1800
1600
600
Totalefficiencyt [%]
880
1180
1471
1770
2060
2350
2650
2950
3240
3530
3830
4120
4410
4710
5000
5300
5600
5890
2.80
Sp
ee
d[r
pm
]
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 26 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 200 mm
Fan curves for nominal length 800 mm (31.5 inch)The indicated shaft power consumption does not includethe loss in the belt drive
Test conditions for the fan curves
The indicated curves are valid for an air density of
ρ =0.075 lb/ft³ (1.2 kg/m3). The rating tests where done aslaboratory test according to EN ISO 5801:2008 with unre-stricted inlet and discharge. Fans with a drive power> 4.0 hp(3.0 kW) must be smoothly started.
20
30
40
50
60
70
80
90
200
300
400
500
1800 = max rated speed
150
100
Sta
ticp
ress
ure
p
f[in
chw
g]
Sta
tic
pre
ss
ure
p
f[P
a]
V [m3/h]
V [cfm]
Pd [Pa]
Pd [inch wg]
Sp
ee
d[r
pm
]
ρ = 0.075 lb/ft³ (1.2 kg/m3)
0.08
0.12
0.16
0.20
0.24
0.28
0.32
0.36
0.80
1.20
1.60
2.00
0.60
0.40
0.08
0.12
0.16
0.20
0.24
0.28
0.32
0.36
0.40
0.80
1.20
0.60
4.0/3.0
1.5/1.1
0.50/0.37
2.0/1.5
0.34/0.25
1.0/0.75
0.74/0.55
0.24/0.18
0.16/0.12
0.12/0.09
2000
2800
3600
4400
5200
6000
6800
7600
8400
9200
10000
10800
11600
20 30 40 50 60 70 80 90 100
150
200
300
400
500
600
1400
1600
1200
1000
800
600
10.2/7.55.5/4.0
1180
1650
2100
2600
3060
3530
4000
4470
4940
5420
5890
6360
6830
1.60
2.00
2.40
Totalefficiencyt [%]
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 27 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 200 mm
Fan curves for nominal length 1000 mm (39.37 inch)The indicated shaft power consumption does not includethe loss in the belt drive
Test conditions for the fan curves
The indicated curves are valid for an air density of
ρ =0.075 lb/ft³ (1.2 kg/m3). The rating tests where done aslaboratory test according to EN ISO 5801:2008 with unre-stricted inlet and discharge. Fans with a drive power> 4.0 hp(3.0 kW) must be smoothly started.
1471
1940
2410
2880
3360
3830
4300
4770
5240
5710
0.016
0.024
0.032
0.04
0.08
0.16
0.24
0.32
0.4
0.8
1600 = max rated speed
Sta
ticp
ress
ure
p
f[in
chw
g]
Sta
tic
pre
ss
ure
p
f[P
a]
V [m3/h]
V [cfm]
Pd [Pa]
Pd [inch wg]
Sp
ee
d[r
pm
]
ρ = 0.075 lb/ft³ (1.2 kg/m3)
Totalefficiencyt [%]
20
30
40
50
60
70
80
90
200
300
400
150
100
0.08
0.12
0.16
0.20
0.24
0.28
0.32
0.36
0.80
1.20
1.60
0.60
0.40
4.0/3.0
1.5/1.1
0.50/0.37
2.0/1.5
0.34/0.25
1.0/0.75
0.74/0.55
0.16/0.12
0.24/0.18
2500
3300
4100
4900
5700
6500
7300
8100
8900
9700
10500
11300
4 6 8 10 20 40 60 80 100
200
400
1400
1200
1000
600
800
6.8/5.05.4/4.0
6180
6650
1.60
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 28 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 200 mm
Fan curves for nominal length 1250 mm (49.21 inch)The indicated shaft power consumption does not includethe loss in the belt drive
Test conditions for the fan curves
The indicated curves are valid for an air density of
ρ =0.075 lb/ft³ (1.2 kg/m3). The rating tests where done aslaboratory test according to EN ISO 5801:2008 with unre-stricted inlet and discharge. Fans with a drive power> 4.0 hp (3.0 kW) must be smoothly started.
1770
2000
2240
2470
2710
2950
3180
3400
3650
3890
4120
4360
4590
4830
5060
5300
5530
20
30
40
50
60
70
80
90
200
300
1200 = max rated speed150
100
Sta
ticpr
essu
re
p f[in
chw
g]
Sta
tic
pre
ss
ure
p
f[P
a]
V [m3/h]
V [cfm]
Pd [Pa]
Pd [in wg]
ρ = 0.075 lb/ft³ (1.2 kg/m3)
0.08
0.12
0.16
0.20
0.24
0.28
0.32
0.36
0.80
1.20
0.60
0.40
0.008
0.016
0.020
0.024
0.032
0.4
0.8
0.16
0.24
0.32
0.4
0.8
1.5/1.1
0.50/0.37
2.0/1.5
0.34/0.25
1.0/0.75
0.74/0.55
0.16/0.12
0.24/0.18
3000
3400
3800
4200
4600
5000
5400
5800
6200
6600
7000
7400
7800
8200
8600
9000
9400
10200
11000
11800
2 4 5 6 8 10 20 40 60 80 100
200
600
1000
800
4.0/3.0
Totalefficiencyt [%]
Sp
ee
d[r
pm
]
5060
6000
6950
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 29 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 150 and 200 mmAcoustical dataThe acoustical data are for discharge side, tested in a re-verberant field.
The A-weighted sound power level LWA can be trans-formed into a A-weighted sound pressure level LPA by theequation LPA=LWA-10 log s/1 m2.
The sound pressure level in the free field in 1 m distance(full spheric sound radiation) is abt. 11 dB less than thesound power level.
The equation for the unweighted sound power level ac-cording to VDI 2081 is:LW=LWspecific+10 log V + 20 log pt
For the total pressure pt use Pa and for the air volume Vuse m3/s.
Unweighted Sound Power Level LW [dB] LW = LWspez + L1 + L2 [dB]
8
6
4
2
0
L3 [dB]
Fan Speed n [rpm]
500 1000 1500 2000 2500 3000
A-weighted Sound Power Level LWA [dBA] LWA = LW-L3 [dBA]
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 30 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 150mm and 200 mm
Accessories and special versionsBelt pulley
V-belt pulley with sleeve, dW = 160 mm (6.3 inch),profile SPA 12.5 mm (0.49 inch), DIN 7753.
With the suction opening on top, viewed against the dis-charge opening, the drive pulley is bolted on optional eitherright hand (TWR) or left hand (TWL).
Belt pulley and taper clamping sleeve are made from greycast iron GG 20.
LTG Accessories:V-belt pulley 1 x SPA Ø 160 mm (6.3 inch)incl. clamping sleeve Ø 24 mm (0.94 inch)Material No. 1004586
Impeller
For extra high corrosion protection requirements, the im-pellers can be made of stainless steel.
Socket head cap screw SW5
90 (3.54)
30 (1.18)
50 (1.97)
26 (1.02)
10 (0.39)
40 (1.57)
d=
160
(6.3
)
20(0.79)
24
(0.9
4)
TW 150: 116 (4.57)
TW 200: 101.5 (4)
Installation, initiation- Clean and degrease all shiny surfaces. Insert taper
clamping sleeve into the hub and bring bores to a flush.- Slightly grease screws and insert. Do not yet tighten the
screws.- Clean and degrease shaft. Push belt pulley with taper
clamping sleeve to the desired position on the shaft.- Tighten the screws uniformly, alternating between the
sides and using a moment of 20 Nm.- Check the moment of the screws after a short period of
service (1/2 to 1 h) and correct if necessary.- To keep foreign bodies from entering the empty bores,
fill them with grease.
Detachment- Loosen all screws. Remove one or two of them com-
pletely, grease and insert them into the ejection bores.- Remove belt pulley with sleeve from the shaft.
© LTG Aktiengesellschaft · Grenzstraße 7 · 70435 Stuttgart · Germany TW-eng-TP (10/14)Tel. +49 (711) 8201-0 · Fax +49 (711) 8201-696 · [email protected] · www.LTG.netPrinted in Germany · Former editions are invalid · Subject to technical modifications page 31 of 32
LTG High Performance Tangential FansSeries TW, impeller diameter 125, 150 and 200 mmSelection
application example your data designations
gas cold air t [F] temperatureU [V] voltagef [Hz] frequencyV [cfm] air volumeρ [lb/ft³] specific gravitypf [in. “wg] static pressurepd [in. “wg] dynamic pressure
at the dischargearea
pt [in. “wg] total pressurec [m/s] velocity at the
discharge area[cu ft/lb] specific gravity
n [rpm] speedt [%] efficiencyPW [hp] shaft power
consumptionLW [dB] sound power levelLWA [dB(A)] A-weighted sound
power levelLpA [dB(A)] A-weighted sound
pressure level
gas temperature t F -4
ambient temperaturedrive sidecounter side
tt
FF
-5-5
condensation yes
located atvehiclerefrigeration
drive side right hand
arrangement horizontal
drive motor
power supply 3-phase
voltage U V 220 / 380
frequency f Hz 50
specified performance
air volume V cfm 4709
static pressure pf in “wg 250
at specific gravity ρ lbcuft 0.075
active impeller length min.max.
LL
inchinch
35.4351.18
total length max. A inch 55.12
procedure
1. air volume V cfm 4709achievable with length 1064, 1264
2. static pressure pf in “wg 1achievable with length [inch] 41.89
3. drive side right handselectedLTG Tangential Fan type TWR150/1064 Nperformance dataair volume V cfm 4709static pressure pf in “wg 250dynamic pressure pd in “wg 1,51total pressure pt in “wg 2.51exhaust velocity c ft/min 4921.25speed n rpm 2000efficiency t % 54shaft power consumption PW hp 3.35smooth starting noacoustical dataLW spez spec. sound powerlevel dB 39.5
L1 dB 3.5L2 dB 56sound power level LW dB 99L3 dB 2.5sound power level A-weighted LWA dBA 96.5sound pressure level in thefree field in 1 m distance(full spherical sound radiation)
LpA dBA 85.5
AIR TECHSYSTEMS
Comfort Air Technology
Air Conditioning Systems
Decentralized Facade Ventilation Units
Fan Coil Units
Induction Units,Active Chilled Beams
Air Diffusers
Linear Air Diffusers
Wall and Floor Mounted Air Diffusers
Swirl Diffusers
Industrial and Special Air Diffusers
Air Distribution
Flow Rate and Pressure Controllers
Shut-off and Balancing Dampers
Silencers
1.Dient zur Identifizierung der letzten Seite
Process Air Technology
Fans
Tangential Fans
Axial Fans
Centrifugal Fans
Fahrtwind-Simulators
Filtration Technology
Suction Nozzles
Dampers
Filters, Dust Collectors
Separators, Compactors
Humidification Technology
Air Humidifiers
Product Humidifiers
Engineering Services
Fluid Engineering
Flow analysis
Flow visualization
CFD-simulations
Flow optimization
Air conditioning concepts
Thermodynamics
Calorimetric performance measurement
Thermal, dynamic, unsteady,system simulations
Acoustics
Sound level measuring
Vibration analysis
Echo chamber measurement
Acoustic optimization
Comfort
Evaluation
Optimization
Customer-specific Solutions
Product development
Process optimization
Installation analysis
LTG AktiengesellschaftGrenzstraße 770435 StuttgartGermanyTel.: +49 (711) 8201-0Fax: +49 (711) 8201-696E-Mail: [email protected]
LTG Incorporated105 Corporate Drive, Suite ESpartanburg, SC 29303USATel.: +1 (864) 599-6340Fax: +1 (864) 599-6344E-Mail: [email protected]
TW-eng-TP (10/14) 450-33