Ultra-Small, Low-Cost, 210MHz, Single-Supply Op Amps with Rail …€¦ · formance with rail-to-rail outputs. Both devices operate from a +4.5V to +11V single supply or from ±2.25V

General DescriptionThe MAX4450 single and MAX4451 dual op amps areunity-gain-stable devices that combine high-speed per-formance with rail-to-rail outputs. Both devices operatefrom a +4.5V to +11V single supply or from ±2.25V to±5.5V dual supplies. The common-mode input voltagerange extends beyond the negative power-supply rail(ground in single-supply applications).The MAX4450/MAX4451 require only 6.5mA of quies-cent supply current per op amp while achieving a210MHz -3dB bandwidth and a 485V/µs slew rate. Bothdevices are an excellent solution in low-power/low-voltage systems that require wide bandwidth, such asvideo, communications, and instrumentation.The MAX4450 is available in the ultra-small 5-pin SC70package, while the MAX4451 is available in space-saving 8-pin SOT23 and SO packages.

ApplicationsSet-Top BoxesSurveillance Video SystemsBattery-Powered InstrumentsVideo Line DriverAnalog-to-Digital Converter InterfaceCCD Imaging SystemsVideo Routing and Switching SystemsDigital Cameras

Features♦ Ultra-Small SC705 and SOT23 Packages

♦ Low Cost

♦ High Speed210MHz -3dB Bandwidth 55MHz 0.1dB Gain Flatness485V/µs Slew Rate

♦ Single +4.5V to +11V Operation

♦ Rail-to-Rail Outputs

♦ Input Common-Mode Range Extends Beyond VEE

♦ Low Differential Gain/Phase: 0.02%/0.08°

♦ Low Distortion at 5MHz-65dBc SFDR-63dB Total Harmonic Distortion

MA

X4

45

0/M

AX

44

51

Ultra-Small, Low-Cost, 210MHz, Single-SupplyOp Amps with Rail-to-Rail Outputs

VEE

IN-IN+

1 5 VCCOUT

MAX4450

SC70/SOT23

TOP VIEW

2

3 4

Pin Configurations

500Ω500Ω

75Ω

75Ω

IN

OUT

VIDEO LINE DRIVER

Zo = 75ΩMAX4450

Typical Operating Circuit

19-1522; Rev 4; 11/09

Ordering Information

Pin Configurations continued at end of data sheet.

PART

MAX4450EXK-T

MAX4450EUK-T

MAX4451EKA-T

MAX4451ESA -40°C to +85°C

-40°C to +85°C

-40°C to +85°C

-40°C to +85°C

TEMP RANGEPIN-PACKAGE

5 SC70

5 SOT23

8 SOT23

8 SO

TOPMARK

AAA

ADKP

AAAA

—

________________________________________________________________ Maxim Integrated Products 1

For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.

MA

X4

45

0/M

AX

44

51


2 _______________________________________________________________________________________

ABSOLUTE MAXIMUM RATINGS

DC ELECTRICAL CHARACTERISTICS (VCC = +5V, VEE = 0V, RL = ∞ to VCC/2, VOUT = VCC/2, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)(Note 1)

Supply Voltage (VCC to VEE)................................................+12VIN_-, IN_+, OUT_..............................(VEE - 0.3V) to (VCC + 0.3V)Output Short-Circuit Current to VCC or VEE ......................150mAContinuous Power Dissipation (TA = +70°C)

5-Pin SC70-5 (derate 2.5mW/°C above +70°C) ..........200mW5-Pin SOT23-5 (derate 7.1mW/°C above +70°C)........571mW

8-Pin SOT23-8 (derate 5.26mW/°C above +70°C)......421mW8-Pin SO (derate 5.9mW/°C above +70°C) .................471mW

Operating Temperature Range ...........................-40°C to +85°CStorage Temperature Range .............................-65°C to +150°CLead Temperature (soldering, 10s) .................................+300°C

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functionaloperation of the device at these or at any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposureto absolute maximum rating conditions for extended periods may affect device reliability.

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

VVEE - VCC0.20 2.25

Guaranteed by CMRR testVCMInput Common-Mode Voltage Range

Input Offset Voltage (Note 2)

Input Offset Voltage Matching

VOS 4 26

1.0

mV

mV

µV/°C8TCVOSInput Offset VoltageTemperature Coefficient

Input Bias Current

Input Offset Current

IBIOS

(Note 2)

(Note 2)

6.5 20

0.5 4

µA

µAkΩ70Differential mode (-1V ≤ VIN ≤ +1V)

RINInput ResistanceCommon mode (-0.2V ≤ VCM ≤ +2.75V) 3 MΩ

dB70 95

50 60

48 58

57

dB

V

0.05 0.20

0.05 0.15

0.30 0.50

0.25 0.80

0.5 0.80

0.5 1.75

45 70mA

mA

Ω8

±120

46 62dB

V

54 69

4.5 11.0

6.5 9.0 mA

VCC to VEE

VEE = -5V, VCM = 0V

VEE = 0V, VCM = 2VVCC = 5V

Sinking or sourcing

VOL - VEE

VCC - VOH

VOL - VEE

VCC - VOH

VOL - VEE

VCC - VOH

1V ≤ VOUT ≤ 4V, RL = 50Ω0.5V ≤ VOUT ≤ 4.5V, RL = 150Ω0.25V ≤ VOUT ≤ 4.75V, RL = 2kΩ(VEE - 0.2V) ≤ VCM ≤ (VCC - 2.25V)

RL = 2kΩ

RL = 150Ω

RL = 75Ω

IS

VS

PSRR

ROUT

ISC

IOUT

VOUT

AVOL

CMRRCommon-Mode Rejection Ratio

Open-Loop Gain (Note 2)

Output Voltage Swing(Note 2)

Output Current

Output Short-Circuit Current

Open-Loop Output Resistance

Power-Supply Rejection Ratio(Note 3)

Operating Supply-VoltageRange

Quiescent Supply Current (per amplifier)

RL = 50Ω25 50

Sourcing

Sinking

MA

X4

45

0/M

AX

44

51


_______________________________________________________________________________________ 3

AC ELECTRICAL CHARACTERISTICS (VCC = +5V, VEE = 0V, VCM = +2.5V, RF = 24Ω, RL = 100Ω to VCC/2, VOUT = VCC/2, AVCL = +1V/V, TA = +25°C, unless otherwisenoted.)

PARAMETER SYMBOL MIN TYP MAX UNITS

2nd harmonic

3rd harmonic

Total harmonic distortion

Spurious-Free DynamicRange

SFDR -65

Bandwidth for 0.1dB GainFlatness

BW0.1dB 55 MHz

Large-Signal -3dB Bandwidth BWLS 175 MHz

485

Settling Time to 0.1% tS 16 ns

Rise/Fall Time tR, tF 4 ns

-65

VOUT = 100mVP-P

Small-Signal -3dB Bandwidth BWSS 210 MHz

dBcfC = 5MHz, VOUT = 2VP-P

Harmonic Distortion HD-58

-63

dBc

Two-Tone, Third-OrderIntermodulation Distortion

IP3 66 dBc

Input 1dB Compression Point 14 dBm

Differential Phase Error DP 0.08 degrees

Differential Gain Error DG 0.02 %

Input Noise-Voltage Density en 10 nV/√Hz

Input Noise-Current Density in 1.8 pA/√Hz

Input Capacitance CIN 1 pF

Output Impedance ZOUT 1.5 Ω

CONDITIONS

VOUT = 2VP-P

VOUT = 2V step

f1 = 4.7MHz, f2 = 4.8MHz, VOUT = 1VP-P

VOUT = 100mVP-P

fC = 5MHz, VOUT = 2VP-P

fC = 10MHz, AVCL = +2V/V

NTSC, RL = 150ΩNTSC, RL = 150Ω

VOUT = 100mVP-P

f = 10kHz

f = 10kHz

f = 10MHz

Slew Rate SR V/µsVOUT = 2V step

Note 1: All devices are 100% production tested at TA = +25°C. Specifications over temperature limits are guaranteed by design.Note 2: Tested with VCM = +2.5V.Note 3: PSR for single +5V supply tested with VEE = 0V, VCC = +4.5V to +5.5V; PSR for dual ±5V supply tested with VEE = -4.5V to

-5.5V, VCC = +4.5V to +5.5V.

Channel-to-Channel Isolation CHISO 102 dBSpecified at DC

MA

X4

45

0/M

AX

44

51


4 _______________________________________________________________________________________

Typical Operating Characteristics(VCC = +5V, VEE = 0V, VCM = +2.5V, AVCL = +1V/V, RF = 24Ω, RL = 100Ω to VCC/2, TA = +25°C, unless otherwise noted.)

4

-6100k 10M 100M1M 1G

SMALL-SIGNAL GAIN vs. FREQUENCY

MAX

4450

-01

FREQUENCY (Hz)

GAIN

(dB)

-5

-4

-3

-2

-1

0

1

2

3 VOUT = 100mVP-P

4

-6100k 10M 100M1M 1G

LARGE-SIGNAL GAIN vs. FREQUENCY

MAX

4450

-02

FREQUENCY (Hz)

GAIN

(dB)

-5

-4

-3

-2

-1

0

1

2

3 VOUT = 2VP-P

0.4

-0.6100k 10M 100M1M 1G

GAIN FLATNESS vs. FREQUENCY

MAX

4450

-03

FREQUENCY (Hz)

GAIN

(dB)

-0.5

-0.4

-0.3

-0.2

-0.1

0

0.1

0.2

0.3 VOUT = 100mVP-P

100k 10M1M 100M 1G

OUTPUT IMPEDANCE vs. FREQUENCY

MAX

4450

-04

FREQUENCY (Hz)

IMPE

DANC

E (Ω

)

100

0.01

0.1

1

10

2ND HARMONIC

3RD HARMONIC

-10

-100100k 100M10M1M

DISTORTION vs. FREQUENCY

-70

-90

-30

-50

0

-60

-80

-20

-40

MAX

4450

-05

FREQUENCY (Hz)

DIST

ORTI

ON (d

Bc)

VOUT = 2VP-PAVCL = +1V/V

-10

-100100k 100M10M1M


-70

-90

-30

-50

0

-60

-80

-20

-40

MAX

4450

-06

FREQUENCY (Hz)

DIST

ORTI

ON (d

Bc)

2ND HARMONIC

3RD HARMONIC


-10

-100100k 100M10M1M


-70

-90

-30

-50

0

-60

-80

-20

-40

MAX

4450

-07

FREQUENCY (Hz)

DIST

ORTI

ON (d

Bc)

2ND HARMONIC

3RD HARMONIC


-100

-70

-80

-90

-60

-50

-40

-30

-20

-10

0

0 400200 600 800 1000 1200

DISTORTION vs. RESISTIVE LOAD

MAX

4450

-08

RLOAD (Ω)

DIST

ORTI

ON (d

Bc)

2ND HARMONIC

3RD HARMONIC

fO = 5MHzVOUT = 2VP-PAVCL = +1V/V

-100

-70

-80

-90

-60

-50

-40

-30

-20

-10

0

0.5 1.0 1.5 2.0

DISTORTION vs. VOLTAGE SWING

MAX

4450

-09

VOLTAGE SWING (Vp-p)

DIST

ORTI

ON (d

Bc)

fO = 5MHzAVCL = +1V/V

3RD HARMONIC

2ND HARMONIC

MA

X4

45

0/M

AX

44

51


_______________________________________________________________________________________ 5

0 100

0 100

DIFFERENTIAL GAIN AND PHASE

-0.010

00.005

0.015

0.025

IRE

DIFF

PHA

SE (d

egre

es)

DIFF

GAI

N (%

)

MAX

4450

-10

IRE

-0.005

0.020

0.010

-0.04

0.020.04

0.08

0.12

0

0.10

0.06

-0.02

0

-100100k 10M 100M1M 1G

COMMON-MODE REJECTION vs. FREQUENCY

MAX

4450

-11

FREQUENCY (Hz)

CMR

(dB)

-90

-80

-70

-60

-50

-40

-30

-20

-10

PSR

(dB)

0

-100100k 10M 100M1M 1G

POWER-SUPPLY REJECTION

vs. FREQUENCY

MAX

4450

-12

FREQUENCY (Hz)

-90

-80

-70

-60

-50

-40

-30

-20

-10

0

0.4

0.2

0.6

1.2

1.4

1.0

0.8

1.6

0 100 150 200 25050 300 350 400 450 500

OUTPUT VOLTAGE SWING

vs. RESISTIVE LOAD

MAX

4450

-13

RLOAD (Ω)

OUTP

UT V

OLTA

GE S

WIN

G (V

)

VCC - VOH

VOL - VEE

MAX

4450

-14

INPUT50mV/div

OUTPUT50mV/div

SMALL-SIGNAL PULSE RESPONSE

VOLT

AGE

(V)

20ns/div

RF = 24ΩAVCL = +1V/V

INPUT25mV/div

OUTPUT50mV/div


MAX

4450

-15

VOLT

AGE

(V)

20ns/div


INPUT10mV/div

OUTPUT50mV/div


MAX

4450

-16

VOLT

AGE

(V)

20ns/div


INPUT1V/div

OUTPUT1V/div

LARGE-SIGNAL PULSE RESPONSE

MAX

4450

-17

VOLT

AGE

(V)

20ns/div


INPUT500mV/div

OUTPUT1V/div


MAX

4450

-18

VOLT

AGE

(V)

20ns/div


Typical Operating Characteristics (continued)(VCC = +5V, VEE = 0, VCM = +2.5V, AVCL = +1V/V, RF = 24Ω, RL = 100Ω to VCC/2, TA = +25°C, unless otherwise noted.)

MA

X4

45

0/M

AX

44

51


6 _______________________________________________________________________________________

Typical Operating Characteristics (continued)(VCC = +5V, VEE = 0, VCM = +2.5V, AVCL = +1V/V, RF = 24Ω, RL = 100Ω to VCC/2, TA = +25°C, unless otherwise noted.)

20ns/div

INPUT1V/div

INPUT1V/div


MAX

4450

-19

VOLT

AGE

(V)


1 10k10010 1k 100k 1M 10M

VOLTAGE NOISE vs. FREQUENCY

MAX

4450

-20

FREQUENCY (Hz)

1

10

100

RL = 100Ω

VOLT

AGE

NOIS

E (n

V/√

Hz)

9

11

10

13

12

15

14

16

0 200100 300 40050 250150 350 450 500

ISOLATION RESISTANCE vs. CAPACITIVE LOAD

MAX

4450

-22

CLOAD (pF)

R ISO

(Ω)

LARGE SIGNAL (VOUT = 2VP-P)

SMALL SIGNAL (VOUT = 100mVP-P)

0

50

100

150

200

250

300

0 200100 300 400 500 600 700 800

SMALL-SIGNAL BANDWIDTH vs. LOAD RESISTANCE

MAX

4450

-23

RLOAD (Ω)

BAND

WID

TH (M

Hz)

80

0100 1k 10k

OPEN-LOOP GAIN vs. RESISTIVE LOAD

20

10

MAX

4450

-24

RLOAD (Ω)

OPEN

-LOO

P GA

IN (d

Bc)

40

30

50

60

70

CURR

ENT

NOIS

E (p

A/√H

z)

1 10k10010 1k 100k 1M 10M

CURRENT NOISE vs. FREQUENCY

MAX

4450

-21

FREQUENCY (Hz)

1

10

100

RL = 100Ω

MAX4451CROSSTALK vs. FREQUENCY

MAX

4450

-25

FREQUENCY (Hz)

CROS

STAL

K (d

B)

-140

-80

-100

-120

-60

-40

-20

0

20

40

60

0.1M 1M 10M 100M 1G

Detailed DescriptionThe MAX4450/MAX4451 are single-supply, rail-to-rail,voltage-feedback amplifiers that employ current-feed-back techniques to achieve 485V/µs slew rates and210MHz bandwidths. Excellent harmonic distortion anddifferential gain/phase performance make these ampli-fiers an ideal choice for a wide variety of video and RFsignal-processing applications.

The output voltage swings to within 55mV of each sup-ply rail. Local feedback around the output stageensures low open-loop output impedance to reducegain sensitivity to load variations. The input stage per-mits common-mode voltages beyond the negative sup-ply and to within 2.25V of the positive supply rail.

Applications InformationChoosing Resistor Values

Unity-Gain ConfigurationThe MAX4450/MAX4451 are internally compensated forunity gain. When configured for unity gain, the devicesrequire a 24Ω resistor (RF) in series with the feedbackpath. This resistor improves AC response by reducingthe Q of the parallel LC circuit formed by the parasiticfeedback capacitance and inductance.

Inverting and Noninverting ConfigurationsSelect the gain-setting feedback (RF) and input (RG)resistor values to fit your application. Large resistor val-ues increase voltage noise and interact with the amplifi-er’s input and PC board capacitance. This cangenerate undesirable poles and zeros and decreasebandwidth or cause oscillations. For example, a nonin-verting gain-of-two configuration (RF = RG) using 1kΩresistors, combined with 1pF of amplifier input capaci-tance and 1pF of PC board capacitance, causes a poleat 159MHz. Since this pole is within the amplifier band-width, it jeopardizes stability. Reducing the 1kΩ resis-tors to 100Ω extends the pole frequency to 1.59GHz,but could limit output swing by adding 200Ω in parallelwith the amplifier’s load resistor. Table 1 lists suggest-ed feedback and gain resistors, and bandwidths forseveral gain values in the configurations shown inFigures 1a and 1b.

Layout and Power-Supply BypassingThese amplifiers operate from a single +4.5V to +11Vpower supply or from dual ±2.25V to ±5.5V supplies. Forsingle-supply operation, bypass VCC to ground with a

MA

X4

45

0/M

AX

44

51


_______________________________________________________________________________________ 7

Pin Description

PIN

OUT

VEE

IN+

INA-

OUTA

VCC

IN-

INB+

INB-

OUTB

INA+

—

4

—

2

1

8

—

5

6

7

3

1 Amplifier Output

2Negative Power Supplyor Ground (in single-supply operation)

3 Noninverting Input

—Amplifier A InvertingInput

— Amplifier A Output

5 Positive Power Supply

4 Inverting Input

—Amplifier B NoninvertingInput

—Amplifier B InvertingInput

— Amplifier B Output

—Amplifier A NoninvertingInput

IN

RG

VOUT = [1+ (RF / RG)] VIN

RF

RTO

RTIN

RO

VOUTMAX445 _

Figure 1a. Noninverting Gain Configuration

INRG

VOUT = -(RF / RG) VIN

RF

RTO

RS

RTIN

RO

VOUTMAX445 _

Figure 1b. Inverting Gain Configuration

FUNCTIONMAX4450

NAMEMAX4451

Note: RL = RO + RTO; RTIN and RTO are calculated for 50Ω applications. For 75Ω systems, RTO = 75Ω; calculate RTIN from the following equation:

0.1µF capacitor as close to the pin as possible. If operat-ing with dual supplies, bypass each supply with a 0.1µFcapacitor.

Maxim recommends using microstrip and stripline tech-niques to obtain full bandwidth. To ensure that the PCboard does not degrade the amplifier’s performance,design it for a frequency greater than 1GHz. Pay care-ful attention to inputs and outputs to avoid large para-sitic capacitance. Whether or not you use a constant-impedance board, observe the following design guide-lines:

• Don’t use wire-wrap boards; they are too inductive.

• Don’t use IC sockets; they increase parasitic capaci-tance and inductance.

• Use surface-mount instead of through-hole compo-nents for better high-frequency performance.

• Use a PC board with at least two layers; it should beas free from voids as possible.

• Keep signal lines as short and as straight as possi-ble. Do not make 90° turns; round all corners.

Rail-to-Rail Outputs, Ground-Sensing Input

The input common-mode range extends from (VEE - 200mV) to (VCC - 2.25V) with excellent common-mode rejection. Beyond this range, the amplifier outputis a nonlinear function of the input, but does not under-go phase reversal or latchup.

The output swings to within 55mV of either power-supply rail with a 2kΩ load. The input ground sensing

and the rail-to-rail output substantially increase thedynamic range. With a symmetric input in a single +5Vapplication, the input can swing 2.95VP-P and the out-put can swing 4.9VP-P with minimal distortion.

Output Capacitive Loading and StabilityThe MAX4450/MAX4451 are optimized for AC perfor-mance. They are not designed to drive highly reactiveloads, which decrease phase margin and may produceexcessive ringing and oscillation. Figure 2 shows a cir-cuit that eliminates this problem. Figure 3 is a graph ofthe optimal isolation resistor (RS) vs. capacitive load.Figure 4 shows how a capacitive load causes exces-sive peaking of the amplifier’s frequency response ifthe capacitor is not isolated from the amplifier by aresistor. A small isolation resistor (usually 20Ω to 30Ω)placed before the reactive load prevents ringing andoscillation. At higher capacitive loads, AC performanceis controlled by the interaction of the load capacitanceand the isolation resistor. Figure 5 shows the effect of a27Ω isolation resistor on closed-loop response.

Coaxial cable and other transmission lines are easilydriven when properly terminated at both ends with theircharacteristic impedance. Driving back-terminatedtransmission lines essentially eliminates the line’scapacitance.

Table 1. Recommended Component Values

MA

X4

45

0/M

AX

44

51


8 _______________________________________________________________________________________

-25+25-10+10-5+5-2+2-1+1

49.9

10

∞

0

50

1200

GAIN (V/V)

49.9

5

49.9

—

20

500

49.9

15

∞

0

50

500

49.9

11

49.9

—

56

500

49.9

25

100

0

100

500

49.9

25

49.9

—

124

500

49.9

50

62

0

250

500

49.9

95

49.9

—

500

500

49.949.9RTO (Ω)

100210Small-Signal -3dB Bandwidth (MHz)

5649.9RTIN (Ω)

0—RS (Ω)

COMPONENT

500∞RG (Ω)

50024RF (Ω)

R = 75

1-75

R

TIN

G

Ω

MA

X4

45

0/M

AX

44

51


_______________________________________________________________________________________ 9

RG RF

RISO

50Ω

CL

VOUT

VIN

RTIN

MAX445 _

Figure 2. Driving a Capacitive Load Through an Isolation Resistor

30

25

20

5

10

15

0

CAPACITIVE LOAD, CL (pF)500 100 200150 250

ISOL

ATIO

N RE

SIST

ANCE

, RIS

O (Ω

)

Figure 3. Capacitive Load vs. Isolation Resistance

6

-4100k 10M 100M1M 1G

-2

FREQUENCY (Hz)

GAIN

(dB)

0

2

4

5

-3

-1

1

3

CL = 10pF

CL = 15pF

CL = 5pF

Figure 4. Small-Signal Gain vs. Frequency with LoadCapacitance and No Isolation Resistor

3

-7100k 10M 100M1M 1G

-5

FREQUENCY (Hz)

GAIN

(dB)

-3

-1

1

2

-6

-4

-2

0

CL = 68pF

RISO = 27Ω

CL = 120pF

CL = 47pF

Figure 5. Small-Signal Gain vs. Frequency with LoadCapacitance and 27Ω Isolation Resistor

MA

X4

45

0/M

AX

44

51


10 ______________________________________________________________________________________

INB-

INB+VEE

1

2

8

7

VCC

OUTBINA-

INA+

OUTA

SOT23/SO

TOP VIEW

3

4

6

5

MAX4451

Pin Configurations (continued) Chip Information

MAX4450 TRANSISTOR COUNT: 86

MAX4451 TRANSISTOR COUNT: 170

MA

X4

45

0/M

AX

44

51


______________________________________________________________________________________ 11

SC

70, 5

L.E

PS

PACKAGE OUTLINE, 5L SC70

21-0076 11

E

PACKAGE TYPE PACKAGE CODE DOCUMENT NO.

5 SC70 X5-1 21-0076

5 SOT23 U5-2 21-0057

8 SOT23 K8-2 21-0078

8 SO S8-5 21-0041

Package InformationFor the latest package outline information and land patterns, go to www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in thepackage code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to thepackage regardless of RoHS status.

http://pdfserv.maxim-ic.com/package_dwgs/21-0076.PDF




MA

X4

45

0/M

AX

44

51


12 ______________________________________________________________________________________

SO

T-23

5L

.EP

S

Package Information (continued)For the latest package outline information and land patterns, go to www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in thepackage code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to thepackage regardless of RoHS status.

MA

X4

45

0/M

AX

44

51


______________________________________________________________________________________ 13


0

0

MARKING

PACKAGE OUTLINE, SOT-23, 8L BODY

21-0078 I1

1

MA

X4

45

0/M

AX

44

51


14 ______________________________________________________________________________________

SO

ICN

.EP

S

PACKAGE OUTLINE, .150" SOIC

1

121-0041 B

REV.DOCUMENT CONTROL NO.APPROVAL

PROPRIETARY INFORMATION

TITLE:

TOP VIEW

FRONT VIEW

MAX

0.010

0.069

0.019

0.157

0.010

INCHES

0.150

0.007

E

C

DIM

0.014

0.004

B

A1

MIN

0.053A

0.19

3.80 4.00

0.25

MILLIMETERS

0.10

0.35

1.35

MIN

0.49

0.25

MAX

1.75

0.0500.016L 0.40 1.27

0.3940.386D

D

MINDIM

D

INCHES

MAX

9.80 10.00

MILLIMETERS

MIN MAX

16 AC

0.337 0.344 AB8.758.55 14

0.189 0.197 AA5.004.80 8

N MS012

N

SIDE VIEW

H 0.2440.228 5.80 6.20

e 0.050 BSC 1.27 BSC

C

HE

e B A1

A

D

0∞-8∞

L

1

VARIATIONS:



Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses areimplied. Maxim reserves the right to change the circuitry and specifications without notice at any time.

15 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600

© 2009 Maxim Integrated Products Maxim is a registered trademark of Maxim Integrated Products, Inc.

Revision History

REVISIONNUMBER

REVISIONDATE

DESCRIPTIONPAGES

CHANGED

4 11/09 Corrected TOC 20 6

Documents

Ultra-Small, Low-Cost, 210MHz, Single-Supply Op Amps with Rail …€¦ · formance with rail-to-rail outputs. Both devices operate from a +4.5V to +11V single supply or from ±2.25V