TyreCheck 2011

1

TYRECHECK KIT &

CONTENTS

2

KIT CONTENTS:TURN ON POWER HERE

3

Wireless Pressure Stick

Flexi Gauge

2 Chucks & Calibration Block

Connecting PDA & Flexi Gauge via Bluetooth 

Turn on HTC. Go to “Start” and choose

program “TyreCheck.Mobile”.

Enter password and tap the unlock icon.

Turn on the Flexi Gauge by holding down the middle

button until “Measurement”

appears onscreen.

On the HTC, tap the red “Bluetooth”

icon to begin connecting the

devices.

4

Bluetooth icon appears blue

when connected and

red when disconnected.

Connecting PDA & Flexi Gauge via Bluetooth 

The screen will read “Connecting”. This

changes to “Connected” . Once connected you will see the Bluetooth

icon and an image of the device. Use the

Exit icon to return to the previous screen.

Exit Icon

Flexi Gauge Image

Bluetooth Icon

5

First screen displays available

devices. Choose the device to connect to the HTC and select the left/right arrow

icon.

Completing Inspections 

Tap the single bus icon from the Main Menu

Screen. This will bring up the Fleet Screen. Choose your fleet from the

drop down menu.

This icon brings up your

keyboard.

6

Completing Inspections

Tap the middle button on the Flexi Gauge. The Tyrecheck program starts with the left

front tire of the vehicle. Take your pressure and tread depth readings. Press the middle button on the Flexi after each tire to move to the next tire, or select the next tire using the HTC. Click the Flexi’s middle button twice when the inspection

is complete to return to the Vehicle Registration screen.

Repeat the process for each vehicle.

Once fleet is selected, tap on the green spy glass icon, this will bring up a list of vehicles.

If the vehicle you are searching for is not listed, you can manually enter the vehicle #

by tapping the yellow box. The keyboard will appear so you can enter needed vehicle #. Tap green spy glass icon to locate vehicle

with in your fleet. If vehicle is listed, tap vehicle # and then tap the single bus icon to bring up the vehicle

footprint for inspections.

7

TyreCheck Flexi Gauge

Hold down center button to turn on and off

Double Click to toggle between measurement mode and setup mode

Mini USB Connection for charging

Spring loaded Tread reading needle, to allow for repeatable readings

When in Setup Mode use the Navigation Keys to

move around the menus

Large display which lights up when

measurement is taken

Stable footing to enable accurate tread readings

8

COMPLETING INSPECTIONS & PRESSURE CORRECTIONS USING THE PORTABLE AUTOMATIC TIRE INFLATOR

CONNECTING THE INFLATOR VIA BLUETOOTH

1.TURN ON INFLATOR HERE

2.CLICK ON BLUETOOTH ICON

3.TAP GREEN ARROW-DEVICE TWO TO CONNECT

4. INFLATOR ICON WILL BE VISIBLE WHEN CONNECTED

9

COMPLETING INSPECTIONS & PRESSURE CORRECTIONS USING THE PORTABLE AUTOMATIC TIRE INFLATOR

FOLLOWING TREAD DEPTH INSPECTIONS OF EACH TIRE

ATTACH THE AUTOMATIC TIRE INFLATOR HOSE TO RECORD & CORRECT PRESSURE

10

Synchronizing with the HTC

Tap on “TyreCheck.Mobile”.

Enter password and tap the unlock icon.

Tap blue world icon to start synchronizing

14

SYNCHRONIZATION IN PROGRESS

PDA AUTOMATICALLY

SYNCS

WHEN SYNCHRONIZATION IS FINISHED- WILL READ“SYCHRONIZATION COMPLETE” TAP RED EXIT DOOR TO FINISH

12

TO CLOSE TYRECHECK TAP THE RED ICON

THIS WILL RETURN YOU TO THE START UP SCREEN

13

Haltec Corp. Contacts:Toll Free-800.321.6471

Ken Coyne-Office: 330.222.150 Ext.219 Cell:330.310.3510

Kyle Captain-Cell: 304.208.7782

Mike Caron-Office: 330.222.1501 Ext.254 Cell: 330.651.6899

Ryan Stuver-Office: 330.222.1501 Ext. 257 Cell: 330.277.6426

Alex Austin-Office:330.222.1501 Ext. 255

14