Schedule of quantities - HPCLtenders.hpcl.co.in/tenders/tender_prog/TenderFiles/2059...Supplying and Laying of design mix, Reinforced Cement Concrete of following Grades (excluding

Schedule of Quantities for Civil, Structural & Architectural works at Bihta Depot

S.N Item Description Unit Qty

CIVIL, STRUCTURAL & ARCHITECTURAL WORKS

Earthwork in excavation for Foundations of buildings, pipe supports, equipment foundation, dyke wall, drain ,pit, trenches, manholes, etc. or any other place as directed, in Ordinary soils including Soft rock / Disintegrated rock, in both Dry and Wet conditions, including Pumping and Bailing out Surface and Subsoil water, Shoring, Strutting, Slush removal, including backfilling etc, in layers of 150mm at all heights and depths as per Drawing and Specifications wherever required , in Foundation pits, under floors and other places with excavated suitable surplus earth, including reclaiming from spoil heaps kept elsewhere including dressing and leveling, watering and mechanical compaction etc. Transporting surplus soil to unobjectionable place within boundary limits and spreading in layers and as per Specifications and direction of Engineer. The Measurement for payment shall be for the theoretical volume only and it shall be the volume of the block of the excavation having maximum bottom dimension of the foundation as per drawing and to actual depth. (Note: The Contractor shall take into account in his rate, the provision for excess excavation for necessary working space, slope, steps etc., required for excavation, safety and other allied works and refilling the side slopes and working space etc)

1 For depth up to and including 2.0m Cum 4500 2 For depth above 2.0m Cum 1500 3 Controlled earth filling under floors and other places with special compaction to achieve dry

density of 95% standard proctor density with excavated surplus earth including cost of excavation reclaiming from spoil heaps as per instruction of the Engineer at all heights/depths within plant, transporting, depositing, compacting and dressing, trimming complete as desired in layers not exceeding 15 cms including watering, consolidating by mechanical means as per specifications and instructions of the Engineer.

Cum

1200

4 Supplying and filling approved quality sand in foundation or under floor, trenches, pits and other places, at all locations in layers of 200 mm thickness including watering and ramming, all lead, lift and depth complete as per drawing and specification and direction of the Engineer

Cum

250

5 Same as Item 5 above but with murram Cum 50 6 Supplying and injecting with approved quality chemical emulsion at the rates and concentrations as

per IS 6313-1981 Part II for pre constructional anti termite treatment and creating a chemical barrier under and all round the column pits, foundation, wall trenches, plinth filling, junctions of wall and floor, expansion joints, apron, surrounding of pipes, conduits etc., along the perimeter of the building including all bye works complete as per specification and direction of Engineer (only ground floor plinth area of the building will be measured for the payment in the following three stages. i) 50% after completion of the foundations ii) 30% after completion of the ground floor flooring iii) 20% after completion of all treatment works including ground floor doors & windows. Work to be executed by


M/s Pest Control (India) or any other approved agency and specified guarantee for 10 (ten) years shall be furnished by the bidder.

Sqm

1200

7 Supplying and Laying Plain Cement Concrete of Grade 1:4:8 (M7.5) with stone aggregate of 40mm down size (including shuttering if required) in all leveling courses under Foundation, Floors, Pipelines, Pits, trenches etc., at all depths complete all as per Drawings and Specifications and instruction of the Engineer.

Cum

430

Supplying and Laying Plain Cement Concrete of following Grades (including Shuttering if required) in foundation, floors, aprons, pits, drains and other mass Concrete works, Steps, Coping of wall etc., at all level as per Drawings, Specifications and instruction of Engineer.

8 a) 1:3:6 (M-10) Grade Concrete,using 20 mm down graded coarse aggregate. Cum 90 9 b) 1:2:4 (M-15) Grade Concrete,using 20 mm down graded coarse aggregate. Cum 135 10 Supplying & laying reinforcement cement concrete flooring in nominal mix 1:1.5:3 (M20) ( 1 cement:

1.5 sand: 3 coarse aggregate 20mm downgraded) of thickness as mentioned in the drawing of long panels with necessary slope using needle / screed vibrators, etc., in floors and any other works as directed. The rates shall include the cost of necessary steel shuttering (but excluding the cost of steel reinforcement) to maintain the line and level of the floor to achieve a flat and smooth surface within the specified tolerance, cleaning and preparing the base surface and other necessary bye-works, provision for construction joints, expansion joints, etc., all complete as per specification, drawings and direction of the engineer

Cum

350

Supplying and Laying of design mix, Reinforced Cement Concrete of following Grades (excluding Shuttering and Reinforcement) at all depths and heights in all types of Foundations, Footings, equipment foundations, pile cap, columns, pedestal, wall, lintels, ducts, beams, brackets, slabs of all shapes, sills, parapets, bands and any other works both in under ground and Superstructures all complete as per Drawings, Specification and instruction of Engineer.

11 M-25 Grade Design Mix Concrete, using 20 mm down graded coarse aggregate. Cum 1700 12 M-25 Grade Design Mix Concrete for chajjas and fins, facia etc using 12 mm down graded coarse

aggregate. Cum

50

13 Providing, Fixing and Stripping of Shuttering of good quality plywood or steel plate on steel frame for all types of Structures, anchor pockets etc at all depths and heights not covered in respective items including Centering / Scaffolding, all complete as per Drawings, Specifications and directions of the Engineer so as to obtain a smooth surface of concrete free from honeycombing.

Sqm

9200

14 Supplying and Fabricating and Fixing in position Steel Reinforcements of Grade Fe-415 conforming to IS-1786-1985 at all levels and positions including the Cost of transport, Straightening, Cutting, Bending, Cranking, Binding, Welding, Provision of necessary Chairs and Spacers, Preparation of bar bending schedule, Drawings, getting the same approved etc., as per Drawings and Specifications and including Cost of binding wire, Labor etc., all complete for Reinforced Concrete. Only approved


chairs, spacer & overlaps shall be paid. MT 160 15 Providing and mixing of approved water proofing admixture Liquid water proofing compound

(Prolapin 421 IC/Plastocretes - N or equivalent) as per the manufacturer's specification including cost of material, complete, with all bye works as per drawing and instruction of the Engineer.

Litres

500

16 Providing & Grouting of M30 grade with 12mm downgraded aggregate including tamping for Equipments Base plates, Anchor holes etc., with Cement Concrete of the following Grades (including Shuttering wherever necessary) at all levels and as per Drawings, Specifications and direction of the Engineer.

Cum

5

17 Roof screed with M-15 grade concrete (12 mm down graded coarse aggregate) with smooth finish and required slope(min. 25 mm thick & max. 125 mm thick) including mixing of water proof compound as per manufacturer's specification. payment for water proofing compound will be done under relevant item

Cum

150

18 Providing BRICK WORK with frog/indent, conforming to class A as per IS:1077 having crushing strength of not less than 80 kg/cm2, in 1:5 cement mortar in all types of foundation and superstructure at all depths/heights including bands, projections, pillars, parapets, ornamentals of any shape, cornices, all complete including cut work, curing, scaffolding, including filling of joints with CM 1:5 and racking of joints, etc., with all bye-works as per specifications, drawings and directions of the Engineer.

Cum

900

19 Providing BRICK WORK 115 mm thick using bricks, having crushing strength of not less than 80 kg/cm2, in 1:4 cement mortar, including providing reinforcement at every 3rd courses with 2 MS bars of 6 mm dia. and distribution 6 mm dia at 30 cm centre to centre in all locations and heights, as per drawing and as directed by engineer including filling of joints with CM 1:4 and racking of joints.(Reinforcement will not be paid separately)

Sqm

600

20 Providing 20 mm thick external sponge finish cement plaster 1:4 (1 cement : 4 sand) as per architectural shapes marked in the drawings, at all depths and heights in two coats of 12mm & 8mm. 2nd coating 8mm shall be finished with sand faced plastering on faces of walls, pillars, projection, bands, cornices, fins, sills, etc., including raking out joints if any left out, necessary dabbing, curing, scaffolding, providing chicken mesh at junctions of columns, beams etc., complete at all heights as per specification and drawings, second layer with water proofing compound (to be paid under relevant items).

Sqm

3250

21 Providing 12 mm thick cement plaster 1:4 (1 cement: 4 sand) smooth finish with water proofing compound (to be paid under relevant items) as per architectural shapes marked in the drawings, at all depths and heights in one layer on internal faces of walls, pillars, projection, bands, cornices etc., including necessary dabbing, curing, scaffolding, providing chicken mesh at junctions of columns, beams etc. complete at all heights as per specification and drawings.

Sqm

2700

22 Providing 6 mm thick cement plaster 1:4 (1 cement: 4 sand) to ceiling of slabs, chajjas including


drip course, bands, beams, columns, loft slabs, staircases, and any other location at all heights wherever required with all bye works dabbing, curing, scaffolding, including providing chicken mesh at junction of columns, beams etc. complete at all heights and levels as per specification and drawings.

Sqm

2450

23 Providing 12mm thick cement plaster CM 1:4 (1 cement : 4 sand) to apron, drain and any other location at all heights including floating coat of neat cement @ 2.2 kg/sqm wherever required with all bye-works dabbing, curing, complete all heights and levels as per specification and drawings and as directed by engineer.

Sqm

1900

24 Lime punning 1.5 mm thick over plastered surfaces with approved quality lime at all levels and locations including preparation of base, curing, scaffolding with all byeworks complete as per specification and instruction of the Engineer.

Sqm

7000

25 Providing and applying two or more coats (to give a smooth and even shade) of premium plastic emulsion paint conforming to IS:5411 of approved make and shade including cleaning and preparation of surface consisting of application of Plaster of Paris punning over entire surface, filling all holes and depressions with plaster of Paris, applying a coat of cement primer, two or more coats of oil based putty (as per manufacturer's recommendations to give a paste like putty), sandpapering etc. all complete. (In Admn Bldg, Marketing Room & Railway Office)

Sqm

3800

26 Providing and applying waterproof cement paint of approved make and shade with textured finish in two coats at all locations over and including a priming coat over wall surface, etc., including preparation of surface complete with all bye works, specification and direction of the Engineer.(all buildings except Administration Building)

Sqm

3000

27 Whitewashing three or more coats with approved lime at all heights and locations with all bye works including scaffolding complete as per specifications. ( Inside MCC1 &2, Driver’ toilet & Lube Ware house)

Sqm

1600

28 Providing and applying two coats of acid proof paint of approved quality and shade at all locations over and including a coat of approved primer for wall surfaces, ceilings, etc., including preparation of base, scaffolding complete with all bye works, specification and direction of the Engineer. (Battery Room)

Sqm

150

29 Providing and applying two coats of external emulsion paint (Apex)of approved quality and shade, at all locations over and including a priming coat over wall surface, bands, parapet etc., including preparation of surface complete with all bye works complete as per specification and direction of the Engineer. (Administration Building)

Sqm

1600

30 Providing and applying two coats of oil based washable distemper of approved quality and shade at all locations over and including a coat of approved primer for wall surfaces, ceilings, etc., including preparation of base, scaffolding complete with all bye works, specification and direction of the Engineer. ( Security house, driver’ room)

Sqm

400


31 Providing hard core with hard granite stone boulders in aprons and flooring including laying, packing, filling interstices with good quality spalls, dry and wet consolidation with mechanical means, binding with good quality murrum/sand(cost inclusive) with all bye works complete for hard core up to 230 mm thick below floor and 115 mm thick, below apron as per specification and instruction of the Engineer (Consolidated thickness will be paid).

Cum

570

32 Providing and laying 40 mm thick grey cement concrete flooring laid in panels with a maximum panel area of 2.50 sqm. at all locations and levels including skirting,steps, nosing, landing slab etc., consisting of plain cement concrete 1:2:4 base (under bed) 30 mm thick (1 cement : 2 coarse sand : 4 stone chips 12 mm & down) and topping 10 mm thick (net after cutting) of mix 1:1:1 (1 cement : 1 medium sand : 1 fine stone grit upto 3.0 mm size) and finished with a floating coat of neat cement 2.2 Kg of cement per Sqm of flooring, providing glass strips 4 mm thick upto 40 mm deep, complete with all bye works as per specification, drawing, (Chequering in floor finish inclusive if required) and as directed by the Engineer

Sqm

1500

33 Providing and laying granolithic flooring with total thickness as given below, laid monolithically over base concrete in panels with a maximum panel area of 2.50 sqm. at all locations and heights including skirting, treads of steps, nosing, landing slab etc., with under bed consisting of plain cement concrete 1:2:4(1 cement:2coarse sand:4stone chips, 12mm and down) and topping of mix 1:1:1(1cement:1medium sand:1fine stone grit up to 3mm size), supplying and fixing 1.5mm thick aluminium strip for full depth, chequering in floor finish inclusive if required, rounding, sloping, curing, finishing, preparation of slabs, steps, etc., all as per specifications, drawings and directions of the Engineer. a) 25mm thick with 19mm under-bed and 6mm topping mixed with non-metallic floor hardener as per manufacturer's specification and instructions(Fosroc, Sika or equivalent)

Sqm

200

34 Providing and laying 300x300x6.5mm thick tiles & conforming to IS:777 of approved color anti-skid ceramic tiles at all levels and locations using approved first quality tiles in flooring as shown in the drawing laid over and including 20 mm cement mortar bed 1:4, joints filled with white cement mixed with matching shade of pigment etc. complete with all bye works as per specification and direction of Engineer

Sqm

140

35 Same as Item 38 but for glazed tiles (without anti-skid) in skirting / dado including providing bands of approved shade and size with 12 mm thick CM bed 1:3 as shown in the drawing and joints filled with white cement with approved colour pigment complete with all bye works as per specifications and direction of Engineer, fixing tiles with approved fixing adhesive compounds as manufacture's specification using 300 x 200 x 6.5 mm thick glazed tile

Sqm

210

36 Providing and fixing 18 mm thick polished kota stone of 250mm wide of approved shades for window sills etc. as shown in the drawing & including 20mm thick mortar bed CM 1:4, curing, polishing of exposed surfaces and all bye works complete.

RM

120


Providing & laying polished kota stone for flooring, steps, staircase and other places as shown in the drawing over & including 20 mm thick mortar bed (1:4) curing and all bye-works complete.

37 Minimum 20 mm thick polished Kota of approx. 300 mm x 600 mm size for floors & skirting Sqm 150 38 Same as item 37 above but for steps and staircase with marble/granite pattern design Sqm 75 39 Providing & laying polished granite 10mm thick for skirting including 12 mm thick cement mortar of

mix 1:3 backing, curing and all bye-works complete Sqm

75

40 Providing & laying polished granite 18mm thick of approved shade for flooring, platform etc over and including 20 mm thick cement motor bed of mix CM1:4, curing & all bye-works complete (size approx. Size 300 mm x 600 mm)

Sqm

75

41 Providing & laying polished granite for wall lining with special adhesive like araldite or equivalent over 12 mm thick cement motor of mix CM1:3 including pointing in white cement with an admixture of pigment to match the stone slab, backing curing and all bye-works complete.8 mm thick mirror polished & machine cut edge granite of approved shade and size

Sqm

25

42 Providing & laying approved make and colour vitrified ceramic tiles 8mm thick in floors of size min. 600mm x 600mm over 20 mm cement mortar bed 1:4 including cutting of tiles wherever required, pointing the joints in neat white cement with matching pigment, cleaning, washing, curing, etc., complete as per specification and direction of the engineer

Sqm

550

43 Providing & laying vitrified ceramic tiles for skirting including 12 mm thick cement motor of mix 1:3 backing, with joints filled with white cement with matching pigment, curing and all bye-works complete

Sqm

50

44 Providing and laying acid resistant mat finish 8mm thick tiles of approved quality laid on 20 mm thick acid resisting cement mortar bed 1:4 (1 acid resistant cement : 4 sand, sand being coarse and absolutely free from impurities) joints also filled and finished with acid resistant mortar, in flooring and other horizontal surfaces, as shown in drawing at all levels and locations as per the directions of the Engineer and as per manufacturer's specification.

Sqm

20

45 Supplying and fixing exterior grade factory made block board flush door shutters bonded with phenol formaldehyde hot pressed (solid core) including non standard size, single or double hung in doors, wardrobes, cupboards, conforming to IS 2202 specification from approved manufacturer with all bye works complete as per specification and drawing, at all locations with necessary sand blocks, cleats wherever required. The shutters shall be supplied with teakwood internal edge lipping from factory and 6mm external edge lipping shall be provided at site. Both faces teak veneered , 35 mm thick (including 4 heavy duty brass hinges with necessary screws & 6 levers godrej mortice dead lock with grip handle), 1.5mm thick laminate on bothsides of approved shade etc all complete.

Sqm

30

46 Providing and fixing approved factory made paneled door shutters 30mm thick with chemically treated seasoned (Hollock or Honne or approved imported) hardwood styles & rails (vertical styles & top rails 100 mm in width, bottom rail & lock rail 175 mm in width) and panels of 18/19 mm thick


marine ply wood (BWP grade) with necessary rubber buffers, cleats (wherever required) Sqm 10 Providing & fixing colour coated aluminium hardware fittings with approved quality and shade as

per IS specifications/as approved by engineer to woodwork with cadmium plated MS screws, suitable sockets in masonry/concrete surface if required including all bye-works complete as per specification, drawing and instruction of engineers (fittings shall not be paid separately in composite items which specify inclusions of fittings)

47 Butt hinges (extruded section 125 mm x 63 mm x 4 mm) Each 50 48 Tower bolts 250mm x 12mm bolt size (with barrel & bolts of extruded section ) Each 15 49 Tower bolts 150mm x 10mm bolt size (with barrel & bolts of extruded section - Each 10 50 Aldrop 250mm x 16mm dia rod Each 15 51 Grip Handle without Back Plate 150mm long Each 30 52 Door Stopper of double type for doors upto 40mm thick Each 15 53 Providing & fixing Godrej Mortice dead lock 6 levers with back plate, duplicate keys & other fixtures

complete with all bye-works as per specification and instruction of the engineer Each

10

54 Supplying, fitting and fixing fully glazed MS windows and ventilators of approved make in single or composite units both openable and fixed type as per IS:1038 and IS:1361 with all joints flush butt welded including glazing bar, coupling bars, mullions, transoms, lugs, mastic cement, glass panels made of 4mm thick float glass, fixed with standard metal beads and with two coats of synthetic enamel paint of approved colour and quality over a primer to steel frames and including all other standard fixtures like hinges, pressed MS handles and peg stays etc., all complete as per specifications, drawings and directions of Engineer.

Sqm

75

55 Supplying, fabricatiing and fixing of rolling shutters of approved make, as per IS:6248, made of MS laths interlocked together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangement for inside and outside locking, top cover, spring and complete with two coats of synthetic enamel paint of approved shade and colour over a primer coat, making chases in wall/floor, grouting the clamps in PCC - M15 (20mm down size aggregate) all complete as per specifications, drawings and instruction of Engineer with 80x1.25mm thick MS laths, push and pull hand operated with mechanical device chain and crank. The rolling shutter should have provision of manual opening by operating handle from outside. Necessary hardware viz. bushing, handle, gear box etc is included in the item scope.

Sqm

70

56 Supplying, fabricating and fixing in position, pressed steel frames for doors manufactured from commercial steel sheet 1.2mm thick including provision of hinges, lock jambs, beads, brace ties with 4.00mm pressed mild steel welded adjustable lugs with split tail end, mortar guards, lock strike plate, shock absorbers, etc. and painting with two coats of approved synthetic enamel paint over primer coat, as per drawing and instructions of the Engineer, including provision and filling with PCC M-10C

RM

40

57 Supplying and fixing MS door shutters consisting of MS box sections, flats, tubes, sheets, meshes


etc., double/single hung including lugs, locking arrangements as per drawing and painting steel works with two coats of approved synthetic enamel paint over and including a coat of priming complete with all bye works as per specification and direction of the Engineer

KG

1000

58 Supplying, fabricating and fixing MS guard bars/grill made out of MS flats, rods, square bars, etc., to steel windows / ventilators including two coats of synthetic enamel paint over primer coat, all complete as per drawing/approved designs, specifications and directions of the Engineer.

KG

1600

59 Supplying, stretching and straining chain link fencing, 1.8m high, made with 10SWG galvanised steel chain link 50mm mesh, 3mm dia Galvanised steel guard wire at top & bottom, fixing to angle posts of 65x65x6 @ 3.0m c/c and lateral supports with angle 75x75x6 @ change of direction or at 15m c/c including 6mm Galvanised steel rods and galvanised steel J hooks & providing 2 MS flats 50mm x 5mm thick bolted to the vertical post, 50 mm NB (medium) pipe to be clamped at top & bottom along the length of the fencing to the vertical post including excavation, PCC M10 for fixing angle post, two coats of synthetic enamel paint over coat of primer, all complete as per drawings, specifications and as directed by the Engineer. (Note: The supply of all the above items is included in the scope

and payment will be made on Running meter basis)

RM

1000

60 Supplying & fixing 40mm dia and polished stainless steel handrail of 16 gauge fixed rigidly by soldering to the stainless steel verticals of 16 mm x 16 mm, 1 mtr. height approx. 250 mm c/c, 1 long square bar (SS) to be welded to vertical members in middle horizontally, in staircase, balcony etc. with all bye-works at all locations and levels to the full satisfaction of Engineer.

RM

15

61 same as Item 65 but with MS vertical & 1 horizontal MS member welded to the vertical member RM 10 62 Supplying, and fixing MS gates consisting of MS hollow square section, flat and rods etc., double /

single shutter side hung including providing hinges, CI wheels & fixtures, MS rails for wheels with anchors, etc., rollers, guiding plates with lugs, pintols with locking arrangements as per drawings including jamming, lugs and pintols in 1:2:4 concrete (1 cement, 2 sand and 4 stone chips) and with anti corrosive paints and including a coat of primer complete with all bye works as per the drawing and specification and direction of the Engineer

KG

750

63 Providing and fixing in position anodized aluminum glazed window/ventilator of "INDAL" / "JINDAL" / "HINDALCO" standard extruded section or approved equivalent make (size 40mmx44mmx1.4mm) in single or composite units, fixed/openable/ sliding type comprising standard aluminum extruded sections and 4.0mm thick float glass including fixing the frames with lugs and glass with aluminum glazing beads and mastic, to shutter and frames, with all fittings such as stays, locking arrangements, handles, tower bolt etc. including providing 2 mm thick approved quality rubber sealing around window/ventilator all complete as per specifications and drawings and directions of the Engineer.

Sqm

150

64 Providing and fixing anodized aluminum glazed door (single shutter) with standard aluminum "INDAL" / JINDAL / HINDALCO extruded frame(size 101.5mmx44.5x2.5mm) and standard "INDAL"


/JINDAL/HINDALCO shutters with 5.50mm thick sheet glass of approved quality fixed with standard glazing bead inside and outside including all fittings such as handles, 6 lever lock, bolts,2mm thick rubber gaskets around, etc., as per specifications, drawings and directions of the Engineer. The measurement for payments shall be for the full opening including frames. The payment for floor spring shall be made under relevant item:

Sqm

75

65 Providing and fixing "TWIN STYLE" anodized aluminum single shutter/double shutter doors fixed on floor springs to open the doors, with 12mm thick polished plate glass fixed to the standard top and bottom style(size 90mmx45mmx3mm) including providing and fixing all fitting such as door handles, 6 lever locking device etc, including 2mm thick approved quality rubber sealing around doors, complete as per manufacturer's specifications, drawings and directions of the Engineer. The payment for floor spring shall be made under relevant item

Sqm

7.5

66 Providing and fixing heavy duty floor spring of approved make for double Action Each 20 67 Providing and fixing heavy duty hydraulic door closer ISI marked, IS:3564 of Everite or approved

make Each 6

68 Providing and laying water proofing treatment with torchable polymeric membrane(incorporating fibre glass tissue and 50 micron HMHDPE as center core)/multiplas'F' or equivalent of approved make and thickness so as to have 4kg/sqm unit weight over roof and other places at all levels and locations, including all necessary bye works like base surface preparation with bitumen emulsion rounding the corners/ends/sides of dissimilar materials, sealing the joint/ends and topping with hot blown bitumen, etc., all complete as per manufacturer’s specifications, drawings and direction of the Engineer. Ten years guarantee shall be given by the agency.

Sqm

1350

69 Providing and fixing 30 mm thick (Forex or equivalent) PVC panel door of approved shade and design made out of 5 mm thick C channel of width 50mm to form the styles and rails the inner panel shall be of min 5mm thick which is welded/sealed to the style and rails along with 5x25mm PVC beading on all sides and both faces. The shutter frames shall have square SS tube of heavy gauge 20x20mm on all sides complete.

Sqm

25

70 Providing and fixing PVC door frame of size 50x47 mm with a wall thickness of 5mm, made out of extruded 5mm rigid foam sheet, mitre cut at two corners and jointed with 2 nos. of 150mm long brackets of 15x15mm MS square tube in two corners. The two vertical door profiles are to be reinforced with 19x19mm phosphated square tube of 19 gauge & hardwood shall be inserted in the square tube, EPDM rubber gasket weather seal to be provided through out the frame. The door frame shall be fixed to the wall by drilling 100mm long stainless screws through the frame by using PVC fasteners on each side of the verticals. A minimum of 4 nos. of screws to be provided for each vertical member.

RM

75

71 Providing and fixing SINTEX or equivalent approved HDPE water tank of 1000 lts capacity with PVC fittings for inlet, outlet, Over flow, scour float valve, connections of required size and dia.


Including connections and hoisting/fixing the same tank on roof and other places at all heights with all bye-works complete as per manufacturer's specification and direction of the Engineer. (Support of tank on brick/RCC/PCC will be paid under relevant items)

Each

3

72 Providing and fixing SINTEX or equivalent approved HDPE water tank of 500 lts capacity with PVC fittings for inlet, outlet, Over flow, scour float valve, connections of required size and dia. Including connections and hoisting/fixing the same tank on roof and other places at all heights with all bye-works complete as per manufacturer's specification and direction of the Engineer. (Support of tank on brick/RCC/PCC will be paid under relevant items)

Each

2

73 Providing and fixing 20 mm thick white Marble slab for Urinals of approved type, shade and texture , both side mirror polished including cutting parent surface/structure finishing the same at all necessary bye-works to have complete finished work all as per drawing, as directed and up to satisfaction of engineer.(marble slab shall be of single piece for each partition of urinals)

Sqm

5

74 Providing and fixing 18 mm thick polished granite slab for counter top platform of approved shade for oval shaped wash basin including cutting the slab of oval shape with all exposed edges rounding and polished to the full satisfaction of Engineer.

Sqm

10

75 Providing & fixing 940 mm x 465 mm x 178 mm stainless steel sink with drain board (AMC steel or equivalent) complete with all bye-works as per specification & instruction of the engineer

Each

2

76 Filling the top 10mm groove around pump foundations with mastic sealant including all bye works complete as per instruction of Engineer.

RM

125

Providing & erecting in position precast concrete trench cover units of specified sizes and thickness using reinforced cement concrete of grade M25 with 20 mm down graded coarse aggregates including formwork to give fair and smooth finish, casting, vibrating using storing, providing lifting arrangement, loading / unloading transporting, load testing etc., complete but excluding cost of reinforcement, all as per specification and as directed by the engineer.

77 Unit weight up to and including 100 kg Cum 5 78 Unit weight exceeding 100kg but not exceeding 200 kgs Cum 2 79 Providing & fixing GI water spouts of 40 mm NB light variety pipes including making grooves and

making the surface smooth after finish of work. RM

10

80 Supplying and laying GI pipes 80 mm dia of medium class of Indian Tube Company/ Zenith or equivalent approved make conforming to IS 1239 with all necessary fittings such as bends, unions, clamps, fixtures, etc., including necessary earthwork, painting, threading, provision of pull wire etc., complete as per specification (including concealing below floor/ ground) for cable entry work etc or as directed.

RM

200

81 Same as above but for 50mm dia pipe RM 200 82 Supplying and laying RCC non pressure pipes of NP2 class and 250mm diameter including collars,

jointed with stiff mixture of CM 1:2 proportion, curing, aligning and joining etc. to correct slope


including excavation, backfilling at all depths as per approved drawings for water/ /cable with all bye works complete as per specification and directions of Engineer.

RM

25

83 Supplying and fixing truly leveled and aligned false flooring / cavity flooring upto 600mm deep consisting of A. 3mm thick, 30mm dia hot dip galvanized M.S. seamless pipe studs @ 610 mm c/c both ways fixed to flooring with M.S. base plates and M.S. check nut welded to base plates. B. 100mm x 100mm x 8mm hot dip galvanized M.S. base plate @ 610mm c/c both way fixed to floor with nos. 40mm long, 6mm dia M.S. dash fasteners. C. Jack head made of pressure die cast aluminium alloy, 2.5mm thick, having channel shaped projections in four directions held by 5mm thick brackets, four pin heads on top, 30mm dia, 30mm long sleeve fitted underside of the jack head. The jack head fixed to pipe studs with two M.S. checknuts to provide level adjustment up to 25mm. D. Machine cut cold rolled, M.S. channels of 40mm x 40mm x 3.15 mm section snapped on to the jack head and fixed by countersunk screw in both directions to form a grid of 610mmx610mm. E. Truly leveled and aligned removable floor panels consisting of 35mm thick particle board conforming to IS 3087 (3 layer flat pressed, bonded with BWP type phenol formaldehyde synthetic resin as per IS:848, categorised as class-1 as per IS:1642 for surface of very low frame spread) with 0.05mm thick aluminium foil facing at bottom and 12mm x12mmx 2mm thick, 75mm long aluminum channel cleats fixed to the bottom of panel on four sides to keep the panel in position and hard PVC liping on four side edges. Including all screws, bolts, adhesives, treating the underneath floor with 3 coats of polyether based two component polyurethane floor coating, numbering each panel at bottom surface, providing cutouts in panels for cables etc., adjusting the grid as per flooring pattern etc. all complete with floor panels finished on top with 2mm thick approved quality high pressure laminate conforming to BS: 476 (Part - 7). The shade of the flooring material shall be as specified in the drawing or as directed by Engineer. ( The cost includes supply of 1% spare tiles and pedestals lifting tools)

Sqm

75

84 Supply & fixing 100 X 100 X 4 mm size M S fan box in RCC slab. Rate to include providing and fixing panel rod 12 mm dia. X 400 mm long fixed in slab, S type hook, straightening, cleaning and applying two coats of enamel paint over a coat of primer.

Nos

30

85 Providing damp proof course over plinth with cement concrete grade 1:1.5:3 using aggregate of 10 mm and down graded and mixing approved water proof admixture with cement as per manufacturer's specification including necessary formwork/ shuttering, one coat of hot bitumen of suitable grade over the top surface of Damp proof coarse and all necessary bye works complete as per specification, drawing and as directed by the Engineer.

Cum

15

86 Supplying, fitting and fixing white/color glazed vitreous china wash basin of superior quality of size 550x400mm (HSW No. 10.001 or approved equivalent make with ISI mark) having single or double holes with 32mm CP brass waste fittings, 32mm CP brass bottle trap, 15mm PVC inlet water pipe connection, painted CI brackets etc. all complete.

Each

6

87 Supplying and fixing ceramic PASTEL COLOUR OVAL BELOW COUNTER BASIN of Parryware size


550x450 mm make No. 550 0418, CP flush valve, CP pipe connection, CP waste coupling , CP Brass bottle trap, 32 mm PVC waste line of required length etc. all complete as per the direction of Engg.-In-Charge. Approved Equivalent - Hindware 10016 Oval

Each

6

88 Providing and fixing vitreous china white/color glazed Indian type water closet of superior quality 580mm size Orissa pan (HSW No. 20.004 or approved equivalent make with ISI mark) with 'P' or 'S' trap, vent hole, with low level PVC/vitreous china white/colour/colour glazed cistern of 10 litres capacity of approved make, syphon & standard flush fittings, CP connecting flush pipe, 15mm CP brass concealed stop cock deluxe type, 15mm dia flexible PVC inlet water connection etc. all complete.

Each

3

89 Providing and fixing white/colour glazed vitreous china pedestal type water closet (EWC) of superior quality 40cm high conforming to HSW No. 20.007 or approved equivalent make with ISI mark, double trap syphonic pattern, 'P' or 'S' trap, with cistern with cover HSW No. 21004 or equivalent approved make with ISI mark having 10 litres capacity with ceramic syphon and fittings (HSW or equivalent make), white/colour colour solid plastic seat cover & lid of superior approved quality, CP brass bar hinges, screws, bolts, rubber, buffers 15mm dia CP inlet waste pipe connection and concealed CP brass stop cock, fixing EWC to floor with necessary TEAK WOOD block & brass screws, all complete as per drawings, specifications and directions of the Engineer.

Each

7

90 Providing and fixing white/colour glazed vitreous china flat back, front lipped standing urinal size 610x400x380mm of superior quality HSW No. 60.002 or equivalent approved make with ISI mark in range or singly with push type CP flush valve, 15mm dia CP brass spreaders, and 32mm dia PVC waste pipe upto floor all as per directions of the Engineer (partitions excluded):

Each

10

91 Providing and fixing box type half-round white glazed channels 100mm size with dead and outlet ends of approved make, set in cement mortar 1:3 and joints finished with white cement

RM

10

92 Providing 5.5mm thick polished plate glass mirror of approved make with 6mm thick asbestos sheet backing including fixing to wall by means of rawl plugs, all complete

Sqm

5

93 Providing and fixing 600 x 120 x 5.5mm thick plate glass shelf with CP guard rail Each 6 94 Providing and fixing vitreous china white/colour glazed soap tray of superior quality HSW No. 40.010

or approved equivalent Each

8

95 Supplying and fixing CP brass soap container (Tilting type) Each 6 96 Providing and fixing recessed toilet paper roll holder including roller white/colour glazed vitreous

china, HSW No. 40.025 or approved equivalent make Each

7

97 Providing and fixing 100 x 75 mm HCI floor/Nahani trap with CP hinged heavy brass grating to be fixed in PCC M15 with 20mm down size aggregate and made water tight

Each

30

98 Construction of brick masonry inspection chamber with full bricks, in CM 1:5, provided with a light duty CI covers conforming to IS:1726 neatly finished including 12mm thick plastering on both faces in CM 1:6, rounding, finishing, excavation, PCC bedding etc., all complete as per specifications and


drawings.Internal size 600x600x600mm deep Each 15 99 Providing yard gully trap 150x100mm with CI grating 150 x 150mm and water tight light weight CI

covers conforming to IS:1726 of size 300x300mm including half-brick masonry in CM (1:4) plastered neatly with CM (1:4) on both faces, 100mm thick PCC bed of mark M-10, necessary excavation, complete as per direction of the Engineer.

Each

7

Providing, fitting and laying H.C.I. Soil and waste pipe including vent pipe with all required H.C.I. Specials, plugs, clamps etc., of approved make, including lead caulked joints 25mm deep, anti corrosive paint inside and both sides for buried pipe, all complete as per specification and direction of Engineer.

100 100mm dia RM 85 101 75mm dia RM 50 Providing, laying and jointing stone ware salt-glazed pipe in CM 1:2 including embedding in PCC

mark M- 10, necessary excavation, & backfilling complete as per specification and depth upto 1.5m (average) (PCC shall be paid separately)

102 100mm dia RM 50 113 150mm dia RM 50 104 200mm dia RM 50 Supplying, fitting and laying GI pipes of heavy quality ('C' class) of ISI marked TATA/Indian Tube

Company/ Zenith or equivalent approved make with all necessary fittings such as bends, tees, elbows, reducers, unions (flanges for pipe size above 50mm), nipples, plugs, clamps, fixtures, etc., including necessary earthwork, painting, etc., complete as per specification (including concealing in walls/floors).

Exposed 105 50mm dia GI Pipe RM 50 106 32mm dia GI Pipe RM 80 107 25mm dia GI pipe RM 85 108 20mm dia GI Pipe RM 10 109 15mm dia GI Pipe RM 10 Concealed with bitumen coating and gunny wrapping/ Teflon tape 110 50mm dia GI Pipe RM 50 111 32mm dia GI pipe RM 10 112 25mm dia GI Pipe RM 25 113 20mm dia GI Pipe RM 45 114 15mm dia GI Pipe RM 75 Supplying, fitting and fixing superior quality gun metal gate valve (full way) of "LEADER" make or


equivalent approved with ISI mark 115 50mm Valve Each 2 116 32mm Valve Each 4 117 25mm Valve Each 5 118 Providing and fitting CP pillar tap of superior quality of approved make with ISI mark (including

connecting flexible PVC connecting pipe) Each 10

119 Providing and fitting 15mm dia CP brass bib cock of superior quality of approved make with ISI mark

Each 15

120 Providing 15mm dia CP Brass stopcock of superior quality (Male/Female end) with ISI mark Each 15 121 Providing and fitting long body CP bib tap of superior quality with ISI mark Each 5 122 Supplying, fitting and fixing heavy type anodized aluminum towel rail with brackets of approved

quality fixed on wooden plugs with CP screws, all complete Each 8

123 Supply, fitting and fixing white/color glazed vitreous china laboratory sink of size 530x430x180mm (HSW No. 50.001 or approved equivalent with ISI mark) with spout of GEM 1031 or approved equivalent with ISI mark, with 15mm inlet pipe, PVC waste pipe & coupling and PVC floor trap, painted metallic brackets, all complete

Each

2

124 Supplying, jointing, cutting and fixing in position PVC rain water down pipes of 100mm dia of following diameters, including all necessary specials like bends, shoes, tees, clamps etc. jointing as per manufacturer’s recommendation, complete as per specifications, drawings and directions of the Engineer.

RM

350

125 Supplying and fixing HDPE rain water down pipe of diameter 200m in Tank Truck Gantry and Sealing Platform, including jointing, bends, specials, clamping etc all complete as per approved drawing and direction of Engineer-in-Charge.

RM

25

126 Construction of soak-pit of size 2500mm dia and 3000mm depth conforming to IS:2470 (Part-I) and as per drawing and directions of the Engineer, including all materials, labour, excavation, backfilling and other bye-works, complete in all respects

Each

3

127 Septic Tank: Supply and Construction of Septic tank of following user capacity confirming to IS : 2470 Part-1 as per approved drawing and direction of EIC. Job also includes supply of all material , labour, construction, excavation, backfilling and other bye works, complete in all respect.

Each

127 20 user capacity Each 1 128 50 user capacity Each 2 129 Paver Block-Supply and laying 80mm thick glazed interlocking blocks of approved colors in approved

design and pattern as directed, of compressive strength 300Kg/sq. cm. placing each against its neighbour on the un-compacted sand, cutting the pieces to fill up edges next to the edge restrains. After laying compact with vibrator. Sweep dry fine sand over the surface, making sure it fills all the gaps between the paver. Vibrate the area again to give strong interlocking bond. Sweep off excess


sand including all work complete as per direction of engineer-in-charge. (interlocking blocks pattern to be approved by Owner)

Sqm

300

130 MS Grating: Preparation of all necessary fabrication drawings including bill of materials, Supply of steel, consisting of flats size 25x6 & 25x3 or any other size as directed including straightening of raw steel if required, fabrication of MS Gratings as per drawings (including preparation of supplementary sketches and detailed bill of materials) including welding electrodes and all other consumables, as required, cleaning and preparation of all steel surfaces to Swedish Standard SA 2 ½ for painting, supply and application of 2 coats of red oxide zinc phosphate primer and 2 coats of synthetic enamel paint so as to achive min. DFT of 120 microns,. Loading, transportation and unloading and delivery at erection site of all fabricated grating structures, erection, alignment and welding, including rectification if any, site assembly all as per technical specifications and drawings, touch up painting, including supply of paint, where paint is damaged.

MT 18

131 Structural steel: Preparation of all necessary fabrication drawings including bill of materials, supply of steel consisting of plates, rolled steel joists, channels, angles, chequered plates, tubes etc and also rectangular / square hollow steel sections, insert plates in RCC/Brickwork, anchor bolts for steel structure, sleeve pipes, anchor nuts, washers etc ,straightening of raw steel if required, fabrication of steel structures as per drawings (including preparation of supplementary sketches and detailed bill of materials) supply of bolts, nuts, washers, shims, packs, putty. gas, welding electrodes and all other consumables, as required, cleaning and preparation of all steel surfaces to Swedish Standard SA 2 1/2 for painting supply and application of primer painting consisting of two coats of Red Oxide Zinc Phosphate primer 30 to 35 microns DFT each and Finish painting shall consists of two coats of Synthetic Enamel 30 to 35 microns DFT each. Finishing Coat shall be applied one before erection and one coat after erection. Total thickness of paint shall be minimum 120 microns DFT. The scope includes loading, transportation ,unloading and delivery at erection site of all fabricated structures, erection, alignment and welding of all structures true to line, level, plumb and dimension, including rectification if any, splicing, site assembly all as per technical specifications and drawings, touch up painting, including supply of paint, where paint is damaged.

MT 220

132 False ceiling consisting of 255/305mm x 1250mm or 600mm x 600mm size Aluminum planks (profiled for positive engagement into clip-in profiles and demounting of individual planks) manufactured out of 0.7mm thk. Aluminium alloy ISH3 conforming to ASTM-1050 with stove enamelled (coil coated) finish in approved colour and suspension system consisting of 0.5mm thk. 40mm x 20mm galvanised steel clip-in main runner profiles (@ 1250mm or 600mm as per plank size) supported by and including 0.5mm thk. 25mm x 16mm GI suspension angle,1mm thk. 25mm x 34mm x 76mm CRCA zinc plated steel ceiling brackets (@ max. 1200mm c/c) fixed to roof slab/beam,0.5mm thk. 41mm wide,105mm high GI hold on clamps slotted for level adjustment, perimeter angles including providing slit openings for fixing supply/return air grill, lighting fixtures, AC

Sqm 300


ducts etc. all complete. Opening made 133 Hume Pipe 500mm dia: Supplying and laying in position RCC pipes of size 500mm with collars,

conforming to IS:458 for pipe culverts, cable crossings etc. including cutting the pipe if necessary, lowering, laying in position to proper levels, slopes etc. caulking the joints with spun yarn soaked in neat cement slurry and finishing with cement mortar 1:2 (1 cement : 2 sand) curing etc. all complete as per drawings, specifications and directions of Engineer-in-Charge. The excavation, PCC and curb wall at ends shall be paid under relevant items. The scope of work includes backfilling & compaction in layers.

RM 20

134 Supplying and laying in position PVC pipes of 160mm OD conforming to IS:4985 for cable crossings, including cutting the pipe if necessary, lowering, laying in position to proper levels, slopes etc. providing proper jointing as per code requirements or manufacturers recommendations etc. all complete as per drawings, specifications and directions of Engineer-in-Charge.

RM 20

135 PVC Water stopper: Supplying and fixing 5mm thick, 230mm width thick PVC water stopper in RCC under ground sump tank or any other place as directed, including providing necessary overlaps, preparation of surface and jointing, necessary support so as to maintain correct line and level to facilitate a leak proof joint all complete as per manufacturer’s recommendation and direction of Engineer-in-Charge.

RM 30

136 Brick Pitching: Supplying and providing brick pitching on edge in herringbone pattern with bricks having compressive strength of min. 50kg/cm2 in cement mortar 1:6 including preparation of surface to required line and level, curing, filling joints, raking out joints complete as per drawing and direction of Engineer-in-Charge. At every 2.0m centre to centre, a band of 250mm width needs to be made by inserting bricks for full 250mm depth from top to bottom of slope.

Sqm 200

137 Preparation of sheeting drawings, Supply, transportation and delivery at erection site of 6 mm thick fibre cement corrugated sheets (Non- Asbestos Cement sheets) on roof and sides. Preparation of detailed bill of materials, supply and fixing of all necessary flashings, corners, ridges, fittings and fixtures, bitumen washers ,GI diamond or limpet washers, including cutting of sheets to required shapes and sizes, and fixing them in position using galvanized hook bolts with all labour and materials etc. complete in all respects as per drawings & specifications. (Net laid area to be measured). The scope includes supplying and application of 3 coats of white wash on the underside.

Sqm 3500

138 Preparation of sheeting drawings, procurement, transportation and delivery at erection site of colour coated steel sheets for roof & side cladding shall be of Galvalume/zincalume BHP steel sheet made of cold rolled steel of 300 MPA minimum yield strength conforming to ASTM A366 or AS 1595. Base metal thickness shall be 0.6mm and total thickness of colour coated profiled sheet shall be 0.68mm. Fixing of sheets with all flashings, corners, ridges, cutting, bending of sheets to a required shape & size and erecting them in roof & sides with all fixing arrangement as per manufactures instructions and complete in all respect as per drawings and specifications. (Net laid area to be measured.)

Sqm 350


139 INTERNAL PARTITION WORKS Framework: Providing and fixing in position Exterior Grade MDF frame work Size out of 50mm x

35mm for partitions, panelling, boxing, soffits with vertical members at not more than 450 mm centers and horizontal members not more than 450 mm centers complete including necessary additional supports, bracing runner etc. complete as per drawing and directions. Item to be completed in all respects as per drawings & instructions from Project-in-charge. Rate to include applying fire retardent paint of approved make on the finished frame work. The frame work should be applied with fire retardant paint before fixing the same.

Sqm 275

140 SKINNING / PANELLING / BOXING: Providing and fixing in position 12mm thick Exterior Grade MDF board on the frame fixed vide above item. Item to be completed in all respects as per approved drawings & instructions from Project-in-charge. Rate to include applying fire retardant paint of approved make on the inner side of the board(Actual executed area will be measured, in this case both sides of the partition where the paneling is done will be measured.)

Sqm 550

141 Low Height Partition: Providing and fixing in position 6mm thick fire retardant plywood. Item to be completed in all respects as per drawings & instructions from Project-in-charge for Low height partitions. (Actual executed area will be measured as mentioned above for 12mm MDF board). The item includes include cutting of ply to any shape & size and fixing the same for receiving finish on the same. No wastage over & above the actual measurement area will be paid.

Sqm 60

142 Providing and fixing 8mm thick glass in partition of approved make ( MODI GUARD / SAINT GOVIN etc ), of appropriate size as per approved drawings and design with necessary wooden mouldings / biddings to hold the glass in position . All exposed wooden surfaces has to be finished with 2/3 coats of malamine polish.

Sqm 60

143 Providing and fixing laminates of 1.5mm thickness of approved make, shade and quality over the MDF Board and Ply wood. Actual executed area will be measured as two sides of same partition are likely to have different finishes. Rate of this item shall include cost of providing fixing wooden facia, if any, matching laminate in approved pattern , skirting, Cornice Moulding at both door level and false ceiling level , Top Cap moulding in case of Low Height Partition etc. as per details and finished in melamine polish of wooden and veneered surfaces for which no extra payment shall be made but shall measured alongwith the partition dimensions . The finishing material shall be fixed in required divisions/panels/ pattern with proper grooves etc. as per drawings & directions. Item to be completed in all respects as per drawings & instructions from Project- in-charge.

Sqm 550

144 CREDENZA UNITS/SIDE UNITS: Providing & fixing in position credenza units made out of 19 mm marine ply with laminate of approved shade & make (Laminate 1.5mm thk.) Only front area to be measured. , for officers & staff in general office area and cabin with 2 shelves & 1 drawers, as per approved drawings, out of 19mm thk plywood finished with material specified below from

Sqm 35


outside & french polish from inside. Item to be completed in all respect as per drawing & instructions from EIC. The item shall include two key board trays, one drawer box with a set of drawers and sliding shutters below key board trays as per the drawing and details. All shelves, sliding shutters, drawer box, drawer front etc. shall be out of 19 mm thick plywood. Drawer sides shall be in 12 mm thk. plywood. Drawer bottom shall be in 6 mm thk. plywood. The exposed surfaces to be finished as follows and wooden exposed edges are to be finished with 2/3 coats of malamine finish.

145 Door Frame for Wall: Providing and fixing Teakwood door frame of finished size 125 x 65mm rebated as required and painted in 3 coats of synthetic enamel paint over 1 coat of wood primer or 3 coats of melamine polish as per details. The frame should be fixed to concrete/brick surface by means of M.S. Holdfasts 25 x 4 x 230 mm 6 Nos. per frame and grouted in position in situ in PCC 1:2:4 blocks having minimu volume of 0.25 Cft., for concrete surfaces and for cabins 12mm diameter countersunk anchore bolts or coach screws shall be used for fixing of all door frames. Tolerance allowable for finished frame sections shall be +/- 3mm totally only for all dimensions (length breadth & height). Inner surface of Teak Wood frame shall be coated with anti termite solution & painted with black tar. Job also includes making good the wall painted surface with same paint as applied earlier to bring it to the original condition.

RM 60

146 Door frame for Partition :Providing and fixing Teak Wood door frame of finished size 125 x 50mm as per profile as per approved drawing and finished with 3 coats of melamine polish as per details.

RM 10

147 Providing & fixing in position sun control film of approved quality, make and shade on windows / glass partitions.

Sqm 75

148 Providing and fixing Sunflex/ Vista / Mac /approved equivalent make vertical blinds of approved shade. The blinds to be fixed and commissioned as per manufactures specification. The work to be completed as per satisfaction & approval of the EIC

Sqm 70

149 Providing and fixing in position pelmet out of 19mm thk. plywood finished with veneer & melamine polish from the front and synthetic enamel paint from inside. Size of the pelmet - 150mm x 150mm. Item to be completed in all respects as per drawings & instructions from Project- in-charge.

RM 20

ELECTRICALS Lighting Distribution Board: 415V, 50Hz, 3 Ph, Neutral & Earth, Column/wall/Recess mounted

Cubicle type lighting distribution boards having IP-52, 2mm thick sheet steel enclosure, cable entry/exit, earthing arrangement, etc., along with LED/Neon indicating lamps. The scope also includes earthing of lighting boards using adequate size PVC insulated single core aluminium cable/GI Strip to the shop earth mat/earth pits including supply of earthing cable/GI strip and all


required materials. 150 Incoming : 100A TPN MCCB, Outgoing : 63A TPN MCB - 3Nos., 32A SPN MCB - 10Nos.,

16/10A SP MCB -6Nos., 16/10A SP MCB with Timer and Contactor -3Nos. Inscription : MLB - ADMIN.BUILDING

Each 1

151 Incoming : 40A TPN MCB, Outgoing : 20/16A SP MCB -21Nos Inscription : LDB1 - ADMIN.BUILDING & LDB2 - ADMIN.BUILDING

2

152 Incoming : 40A TPN MCB, Outgoing : 20/16A SP MCB - 12Nos., 20A SPN MCB -3Nos., 20/16A SP MCB with Timer and Contactor -3Nos. Inscription : LDB-SECURITY COMPLEX

Each 1

153 Incoming : 40A TPN MCB, Outgoing : 32A SPN MCB - 4Nos., 20/16A SP MCB -8Nos Inscription : LDB-MARKETING ROOM

Each 1

154 Incoming : 40A TPN MCB, Outgoing : 16A TPN MCB - 3Nos., 20/16A SP MCB -15Nos Inscription : LDB-MCC ROOM-1 & LDB- MCC ROOM-2

Each 2

155 20A DP switch in sheet steel Enclosure. Inscription: Toilet Block & Parking Shed Each 2 Supply of all materials and point wiring inclusive of circuit wiring using 4 Sq.mm PVC insulated

copper wire in PVC (Medium gauge) concealed conduit supplied and laid on wall/ceiling along with PVC insulated copper wire( for earthing the size of the earthing cable shall be equal to that of circuit/point wiring). The scope of work also includes supply and fixing of sockets, switches, MCB isolators, PVC pipe and all the necessary accessories like junction / pull box, MS mounting box etc., and all connected work for installation as per specification and direction of site engineer. The scope includes wiring from DB to outlet/ switch board and switchboard to fixture.

156 Group control upto four bay light fittings controlled from single phase through MCB Each 5 157 3 Pin, 16A OR 5 pin 6/16A, socket outlet with control switch & socket or industrial 15A socket outlet

with switch and plug top Each 25

158 Air conditioners controlled by 32A/20A DPMCB - G' series (including DP MCB) Each 12 159 20 A 240 V industrial type socket with switch and plug top including socket & plug top. Each 25 Supply of all materials and point wiring inclusive of circuit wiring using 2.5 Sq.mm PVC insulated

copper wire ( from DB to switchboard) with control switches/switch board etc. and point wiring with 1 x 1.5 sq.mm PVC insulated copper wire in PVC CONCEALED CONDUITS supplied and laid on WALL/CEILNG with PVC insulated copper wire for earthing the size of earthing cable shall be equal to that of circuit/point wiring.The scope of work also includes design, fabrication, supply and fixing of all accessories like junction/pull boxes, ceiling roses, straight/slant brass batten holder etc. and all the connected work as per specification and direction of site engineer. all the points for tube lights , decorative GLS wall mounted fittings and points for which no fittings are specified shall be terminated in a brass holder with plastic shrouding to avoid finger contact

160 Light points controlled by one decorative type SP switch. Each 25 161 Two /Three lights controlled by one decorative type switch/MCB Isolator Each 65


162 Ceiling fan points controlled by decorative type switch and regulator (Electronic / Resistance type as approved by owner / consultant).

Each 30

163 Stair case light point controlled by 5A 2 way stair case switch. Each 3 164 3pin 6A Socket outlet with switch including socket or industrial type 5A socket outlet with switch Each 20 165 Supply and fixing GI earth electrode of 65mm dia, earth pit confirming to IS 3043 latest version

installation connecting to earthing main, testing and commissioning of earthing station confirming to tender specification and drawing, including of associated components. Materials like electrode assembly charcoal, salt, sand, CI or RCC lifting covers and civil works involved in excavation back filling and construction of brick chamber as per specification and approved drawing.

Each 10

166 Supply and installation of earthing/Grounding GI strips with anti corrosive coating, trench work and back filling wherever required of size 50mm width x 6mm thk including welding, joint coating, connections etc all complete.

RM 100

167 Supply and fixing of GI wire rope of 10mm dia with lugs at ends for earthing of Lighting and Power distribution boards including connection at both the ends

RM 25

168 Supply, Installation, testing and commissioning of remote operated 1.5TR Split AC units with compressor unit of minimum 3- star rating along with stabilizer as per manufacturer’s recommendation ( min. 3kVA rating) of LG/ Voltas / Blue Star make including all minor civil works, tubing, wiring etc all complete.

Each 12

Supply, installation, testing and commissioning of following type of lighting fixtures including supply and fixing of lamps, ballast, other accessories all complete of Philips/ Bajaj/ Crompton make.

169 Fluorescent tube light luminaire with mounting rails & powder coated reflectors, and lamps suitable for 1 x 36W similar to Philips type TMC 55/136 HPF (MCC Bldg-1&2, Car Parking Shed)

Each 50

170 Fluorescent tube light luminaire with mounting rails & powder coated reflectors, and lamps suitable for 2 x 36W similar to Philips type TMC 55/236 HPF (MCC Bldg 1&2, Sec Complex)

Each 25

171 Decorative surface mounting/ suspended type wide spread mirror optics fluorescent tube light luminaire with lamps, suitable for 2 x 36 w lamp, housing made of CRCA sheet steel powder coated white inside & outside with high purity aluminium reflector and anodised/aluminium plated lamellae similar to Philips type – TCS 605 ( In Admn Buidling(non FC area)/ Mktg Room,Sec Room, Rly office etc)

Each 40

172 Decorative Recess mounting type wide spread mirror optics fluorescent tube light luminaire with lamps, suitable for 4 x 18 w lamp, housing made of CRCA sheet steel powder coated white inside & outside with high purity aluminium reflector and anodised/aluminium plated lamellae similar to Philips type – TBS 300 418 HPF ( size 597mm x 597mm) ( In Admn Buidling, Mktg Room, Rly office etc)

Each 50

173 Corrosion proof tube light fitting with lamp similar to Philips type TDC 10/236 HPF. (Battery Room) Each 2 174 Industrial Integral type Low bay luminaires suitable for SON 70W including control gears, lamps.

Luminaires shall have cast aluminium housing with high purity wide beam anodised aluminium Each 12


reflector, suitable lamp holder, canopy & eye bolt for suspension similar to bajaj make BGELB 70SV. (In Security Complex Canopy)

175 Street lighting luminaire suitable for 1x SON/SON-T 150W or 250 W luminaire shall have die cast aluminum housing, clear flat, toughned glass at bottom, adjustable lamp holder position to suit different installation parameters including lamp and accessories fully wired up with GI pipe bracket suitable for mounting the fittings similar to Bajaj BGEST 150 SV. (Security Complex Roof Top)

Each 4

176 Wall mounted mirror light fitting including lamps suitable for CFL lamps. Mirror light fitting suitable for 1x9W or 11W.CFL lamp with necessary control gear, lamp etc., similar to Bajaj type BJ EX L – 19/111

Each 10

177 Bulkhead fittings with gasket etc., including lamp similar to Bajaj type BJDB - 100 Each 2 178 Supplying and fixing of post top lanterns of Philips make GRC 40/125 LPF or approved equivalent

including all accessories and lamps. (On Main gate & Emergency Gate) Each 8

179 Supply, installation, testing and commissioning of Exhaust fan with 300 MM sweep, single phase propeller type having bird screen mesh / louvers complete with mounting bracket, rubber pads of suitable thickness to absorb vibrations, etc.

Each 12

180 Supply, installation, testing and commissioning of Ceiling fan including suitable down rod and regulator with 6 Step control, control switch including MS box and cover plate for mounting switch etc.

Each 30

181 Supply & laying of 2 pairs of 0.5 mm dia screened & shielded telephone wire in 20 mm dia PVC conduit partly/fully concealed in types of walls, floor etc. complete with all accessories, wiring terminators, connected civil works, rough plastering etc including supply of 16 SWG GI fish wire conduit and accessories

RM 300

182 Supply & fixing of modular type telephone RJ-11connectors in suitable size PVC box concealed to wall, partition including all civil works.

Each 30

183 Supply & fixing of 20 pair telephone tag block with crone connectors housed in suitable MS junction box.

Each 3

184 Supply & laying of CAT 6, 4 pair twisted computer cable screened and shielded in 20/25 mm dia PVC conduit partly/fully concealed in types of walls, floor, partition etc. complete with all accessories, wiring terminators, connected civil works, rough plastering etc including supply of 16 SWG GI fish wire conduit and accessories

RM 300

185 Supply & fixing of modular type of RJ 45 computer connectors in suitable size PVC box concealed to wall, partition etc including all civil works.

Each 20

186 Engineering, preparation of drawing etc for building electrification works of Administration Building, MCC1 & 2, Security Complex, Driver’s toilet, Car parking shed, Railway office(TXR), Marketing room including detailing, BOM preparation, PVC conduit layout, wiring diagram, earthing, telephone wiring, CAT 6 cabling, Panel details etc all complete so as to facilitate execution of the electrical SOR items. Items given in SOR to be taken as input for Bill of Material preparation.

LS 1


Documents

Schedule of quantities - HPCLtenders.hpcl.co.in/tenders/tender_prog/TenderFiles/2059...Supplying and Laying of design mix, Reinforced Cement Concrete of following Grades (excluding