Belgaum Rate Schedule - HPCLtenders.hpcl.co.in/tenders/tender_prog/TenderFiles/3511...SCHEDULE OF RATE FOR MODERNISATION OF RETAIL OUTLETS / CONSTRUCTION OF NEW RETAIL OUTLETS UNDER

SCHEDULE OF RATE FOR MODERNISATION OF RETAIL OUTLETS / CONSTRUCTION OF NEW RETAIL OUTLETS UNDER BELGAUM RETAIL

REGIONAL OFFICE, KARNATAKA STATE.1. Quoted rate shall be applicable for any height, depth, level and thickness of wall etc unless otherwise specified.2. Material shall be tested and shall be approved by EIC before use.3. List of approved make/ brand is attached to techno-commercial bid. Decision of HPCL with regard to selection of make/brand of material to be used shall be final.4. All jobs shall be carried out as per technical specification attached to techno-commercial bid. All IS codes referred to shall be latest edition.5. If any contradiction between item description and General tech Specs/Drawings , the item description shall prevail

1 PART A COMPOUND WALL/ CULVERT/ KERB WALL2 SITE CLEARANCE Surface dressing of the ground including removing trees,

vegetation and making surface levelled and disposal of rubbish outside HPCL's premises to an unobjectionable place, as directed by the Engineer in Charge.

SQM 6

3 BARRICADING: Providing & Fixing in position 8' HT GI sheet ( 22 swg) withangle support (50x50x5 mm ) at every 2.4 m c/c and horizontal support of40x40x5 angle at equal distance for 8' ht &. The Job includes grouting verticalangle supports in RCC 1:2:4, fixing the sheets with necessaru J hooks, paintingwith synthetic enamel paint in Yellow and Black strip combination, anddismantling & disposing off the entire material after completion of work.

SQM 300

4 EXCAVATION5 EXCAVATION - Up to 2 mtr depth Excavation for foundation upto required

depth below existing ground level in any type of soil except hard rock . Rate to include dressing the sides and bottom, bailing out of water if encountered, shoring, strutting, backfilling after the construction of foundation, compacting by the side of the foundation and disposal of surplus excavated earth within/outside HPCL's premises to an unobjectionable place, as directed by the Engineer in Charge including spreading, watering and compaction, complete

CUM 114

6 Excavation in any type of soil except hard rock from 2 m and upto 4 m depth. CUM 146

7 EXCAVATION IN SOFT ROCK - Description same as item no.5 but cutting hard rock by pneumatic hammer and compressor.

CUM 251

8 Excavation of Soft Rock from 2.0m to 4.0m depth. CUM 2929 EXCAVATION IN HARD ROCK - Description same as item no.5 but cutting hard

rock by pneumatic hammer and compressor.CUM 630

10 Excavation of Hard Rock from 2.0m to 4.0m depth. CUM 71011 SAND FILLING Supply and filling with clean approved quality river sand in

layers of 150 mm each including compacting by hand ramming and watering.CUM 1090

12 PCC13 PCC 1:4:8 FOR FOUNDATION Providing and laying PCC 1:4:8 using 40 mm

and down size graded stone aggregates including mixing, providing formwork if required, placing, compacting by hand ramming , curing etc complete.

CUM 2795

14 PCC 1:3:6 mix using 20 mm and down size graded crushed aggregates below flooring, plinth protection, etc.

CUM 3393

15 PCC 1:2:4 mix with 20 to 12 mm size aggregate including mixing, providing formwork if required, placing, compacting by hand ramming , curing etc complete.

CUM 4273

16 PCC 1:2:4 for DPC Providing and laying 50mm thick DPC in PCC 1:2:4 mix with 6 to 12 mm size aggregate and water proofing compound at the rate of 1 Kg per bag of cement.

SQM 256

10000079-HD-11770 1 Signature of bidder and seal

17 PCC 1:2:4 FOR COPING Providing and laying 60 mm average thickness coping in CC 1:2:4 mix using 6 to 12 mm stone aggregate with 40 mm projection on either side of wall with drip mould. Rate to include mixing, providing necessary shuttering, compaction and curing. Thickness of coping at the ends shall be 40 mm and 80 mm at centre . Rate to include 12mm thick plastering of coping concrete with 1:4 cement mortar, providing band etc. complete

CUM 4667

18 PCC 1:2:4 FOR GROUTING ANGLE Providing and laying PCC 1:2:4 mix using 20mm to 12 mm stone aggregate including mixing, providing necessary shuttering, compaction and curing.

CUM 4273

19 REINFORCED CEMENT CONCRETE - Providing , mixing and placing RCC 1:1.5:3 mix using 20 mm and down size graded crushed aggregate including providing and fixing necessary plywood /steel shuttering , scaffolding, machine mixing, compacting by vibrators, curing , hacking the surface to receive plaster etc. complete. Rate shall be exclusive of the cost of steel reinforcement, which will be paid under a separate item. Concrete shall conform to relevant specifications of IS 456 Latest Edition

20 FOOTINGS/PILE CAPS CUM 502021 COLUMNS/ BEAMS CUM 548522 CULVERT SLAB / PRE CAST SLABS CUM 567223 UNDER REAMED PILES -450mm dia pile Providing RCC 1:1.5:3 for under

reamed piles up to required depth with double bulbs as per IS 2911 etc. All complete. Reinforcement steel shall be paid separately. Pile cap shall be paid separately.

RMT

24 300mm dia pile ,same as 21 but for 300 mm dia RMT 115625 230mm dia pile ,same as 21 but for 230 mm dia RMT 90026 REINFORCEMENT STEEL Supply ,fabrication , hoisting and placing in position

TMT steel (Fe 500 Gr) reinforcement bars conforming to IS 1786 -Latest Edition Grade FE 500 as per detailed drawing and specifications including cutting, bending and tying with 18 SWG binding wire complete. The rates shall be applicable for all heights and depths. Payment shall be made as per reinforcement drawings and with theoretical weights only including all authorised laps and hooks. Weight of binding wire shall not be considered for payment.

MT 57386

27 BRICK MASONARY/ RR MASONARY28 BRICK MASONRY WORKS - Providing and constructing following brick

masonry in CM 1:6( mortar thickness should be between 10 to 12mm) using first quality bricks of Class designation 35 (minimum compressive strength 35 Kg/cm2) and conforming to IS-1077-latest edition including providing all openings and projections , raking the joints to 1 cm deep, scaffolding, soaking of bricks in water prior to use and curing etc complete as per specifications .

29 SUB STRUCTURE Providing and laying brick Masonry as above for foundation below DPC level

CUM 4357

30 SUPER STRUCTURES. Providing and laying brick Masonry as above for superstructure above DPC level including scaffolding.

CUM 4554

31 RANDOM RUBBLE MASONRY - Providing and constructing random rubble masonary with good quality stone in CM 1:6 for substructure & superstructure as per IS 1597 part 1, latest edition Rate to include providing through stones @ 2m c/c and curing etc. Complete.

32 SUBSTRUCTURE CUM 275333 SUPERSTRUCTURE Rate to includes scaffolding , raking the joints to 1 cm

deep .CUM 2883

34 Providing and constructing Laterite masonary with good quality laterite stone in CM 1:6 for substructure & superstructure include raking the joints to 1 cm deep

35 SUB STRUCTURE CUM 246536 SUPER STRUCTURE CUM 2663


37 RUBLE PITCHING Providing 230mm thick rubble pitching including surface dressing, making required slope . Rate to exclude flush pointing if required which will be paid separately.

SQM 242

38 POINTING39 Providing flush pointing in ruble pitching with 1:3 cement mortar including curing

etc. complete.SQM 99

40 Providing 12mm raised pointing in RR masonary wall with 1: 3 cement mortar including curing etc. Complete.

SQM 132

41 PLASTERING - Providing and laying average 12 mm thick sand faced cement plaster in single coat in CM 1:4 . -Rate shall include providing necessary scaffolding, GI weld mesh at all joints of brick and concrete surfaces, with a minimum overlap of 150 mm in all directions and curing complete. No extra payment shall be made for additional thickness if required to achieve perfect line and level.

SQM 139

42 WATER PROOF CEMENT PAINT Providing and applying 2 coats of approved water proof cement paint to plastered and concrete surfaces including providing necessary scaffolding, surface preparation etc. complete. If additional coats are required to obtain uniform and smooth finish, the same shall be carried out at no extra cost.

SQM 58

43 WEEP HOLES Providing, fabricating and installing in place, 75 mm dia 4 kg/sqcm or more PVC Pipes of various lengths & at places as directed at site on the masonry wall for water drainage.

RMT 405

44 CHAIN LINK FENCING/ BARBED WIRE FENCING45 STRUCTURAL STEEL FOR CHAIN LINK FENCING /BARBED WIRE FENCING

ETC Supply, fabrication , erection and grouting of 65 x 65 x 6 ISA post and supporting angles of specified length in 1:2:4 concrete grout at every 2.4 m C-C or as advised. Rate to include fabrication of the post as per the specification, erecting, placing, grouting and painting of the posts with two coats of Synthetic Enamel over two coats of Zinc Phosphate Primer Paints and primer shall be of SHALIMAR/ BERGER/ASIAN Make first quality only. Excavation and concrete will be paid separately under ther respective items

MT 56343

46 PIPE RAILING :Supply and fixing of 40 NB medium quality MS pipes conforming to IS 1239 latest addition for top and bottom railings to the angle iron posts for fixing the edges of the chain link fencing. Rate to include fabricating, cutting, bending of the MS pipe where ever necessary. Supply and fixing of the required size MS clamps at every post, with required size nuts and bolts and painting the railing with two coats of Zinc Phosphate Primer and two coats of Synthetic enamel paint after necessary cleaning and scrapping . Paint and primer used shall be of approved make and first quality only.

RMT 472

47 CHAIN LINK FENCING : Supply and fixing of 50 x 50mm opening size 10 SWG GI chain link fencing to the angle iron post with 8 SWG GI hooks and nuts and railing with 14 SWG GI continuous wire (all details shall be as per enclosed drawing ) up to a height of 1.8 m from the ground level. Rate to include unrolling the bundle, erecting, tightening and fixing at 300 mm C-C on the vertical portion of the posts with 14 gauge GI wire. Incase pie railing is not provided continous 12 guageGI wire has to run connecting top and bottom of the fence conecting to the angle posts.

SQM 281

48 BARBED WIRE FENCING Providing and fixing 13 rows horizontal and two diagonals with two ply 12 SWG GI barbed wire fencing with barbes @ 100mm c/c . Angle iron post shall be paid separately. For payment purpose measurement shall be taken for the lenth of plot boundary . No measurement shall be taken for 13 rows individually.

RMT 178


49 HUME PIPE Supplying, laying, joining and aligning 900mm NB NP3 class RCC Hume pipes conforming to IS-458 Latest Edition below approach road whereever directed. Rate to include joining with cement mortar, excavation up to required depth and providing and laying PCC 1:2:4 haunching @ 1m c/c . Test certificates from manufacture shall be submitted and approved by EIC before use.

RMT 5493

50 HUME PIPE 600mm same as above but for 600 NB RMT 408351 HUME PIPE 1000mm same as above but for 1000 NB RMT 612252 PART B SALES BUILDING53 EXCAVATION - Up to 2 mtr depth Excavation for foundation upto required

depth below existing ground level in any type of soil except hard rock . Rate to include dressing the sides and bottom, bailing out of water if encountered, shoring, strutting, backfilling after the construction of foundation, compacting by the side of the foundation and disposal of surplus excavated earth within/outside HPCL's premises to an unobjectionable place, as directed by the Engineer in Charge.

54 Upto 2.0M depth CUM 11455 Above 2.0 M and upto 4.0 M depth CUM 14656 Same as above but cutting hard rock by pneumatic hammer and compressor..

57 Upto 2.0M depth CUM 63058 Above 2.0 M and upto 4.0 M depth CUM 71059 ANTI TERMITE TREATMENT Providing anti-termite treatment including diluting

and injecting Neem base solution and creating a continuous barrier under and alround the column pits, wall trenches, basement excavation, top surface of plinth filing, junction of wall and floor, along the external perimeter of building, expansion joints, over the top surface of consolidated earth on which apron is to be laid, surroundings of pipes and conduits etc. Complete as per specification using Neem based solution. Plinth area of building at ground floor only shall be measured for payment.

SQM 68

60 MURUM FILLING Supplying and filling good quality murum in layers of 150 mm thick including watering and compacting till maximum compaction is achieved as directed by Engineer In Charge.Compacted volume shall be considered for payment.

CUM 311

61 SAND FILLING Supply and filling locally available good quality river sand in layers of 150mm thick including watering and compacting till maximum compaction is achieved as directed by Engineer in Charge. Compacted volume shall be considered for payment.

CUM 1090

62 RUBBLE SOLING Providing and laying 150mm thick rubble soling including hand packing, filling the interstices with chips, spalls and binding with grit and selected murrum, watering, compacting by hand ramming.

SQM 201

63 PLAIN CEMENT CONCRETE Providing and laying PCC of following mix including providing and fixing form work, mixing, compaction and curing etc complete as per specification.

64 PCC 1:4:8 mix using 40 mm and down size graded stone aggregatesbelow footing, in foundation trench etc.

CUM 2795

65 PCC 1:3:6 using 20 mm and down size graded stone aggregates below flooring, plinth protection etc.,

CUM 3393

66 PCC 1:2:4 for DPC Providing and laying 50mm thick DPC in PCC 1:2:4 mix with 6 to 12 mm size aggregate and water proofing compound at the rate of 1 Kg per bag of cement.

SQM 256

67 REINFORCED CEMENT CONCRETE 1:1.5:3 Providing and laying RCC 1:1.5:3 concrete for following works using 20 mm and down size graded crushed aggregate including providing and fixing necessary steel/plywood shuttering, scaffolding, machine mixing, compacting by mechanical vibrators, curing etc complete. Concrete shall conform to IS 456-Latest edition Rate shall be excluding the cost of steel reinforcement, which will be paid under a spearate item.

68 Footings/ Pile cap CUM 5020


69 Pedestals, Columns, Plinth beams, Floor beams, Lintel CUM 548570 Roof Slab, Chajja, staircase CUM 568671 UNDER REAMED PILES -450mm dia pile Providing RCC 1:1.5:3 for under

reamed piles up to required depth with double bulbs as per IS 2911 etc. All complete. Reinforcement steel shall be paid separately. Pile cap shall be paid separately.

RMT

72 300mm dia pile ,same as 71 but for 300 mm dia RMT 115673 230mm dia pile ,same as 71 but for 230 mm dia RMT 90074 STEEL REINFORCEMENT Supplying, fabricating and placing in position TMT

reinforcement bar conforming to IS 1786 grade FE 500 including cutting, bending & supply and binding with 18 SWG annealed binding wire. Payment shall be made as per reinforcement drawings and as per theoretical weights only. Authorised chairs, spacers and laps will be considered for payment. Weight of binding wire shall not be considered for payment.

MT 57386

75 BRICK MASONARY Providing and constructing brick masonry in CM 1:6 using bricks having minimum compressive strength 35 Kg/cm2 and conforming to IS:1077- Latest Edition including providing all openings and projections as per the drawing, raking the joints to 1 cm deep, scaffolding, soaking of bricks prior to use and curing etc complete as per specifications.

76 230 mm & above thickness in walls CUM 455477 115 mm thick Brick masonry in partition walls in CM 1:4. Rate to include

providing 75 mm thick RCC 1:2:4 bands using 2 nos 8 mm dia Torsteel reinforcement at every 1 M height of wall including shuttering. Steel reinforcement shall be paid for separately.

SQM 627

78 PLASTERING79 SAND FACED PLASTER (EXTERNAL) Providing and laying average 18 mm

thick sand faced cement plaster as per following procedure : Apply 12 mm thickcoat of CM 1:4 mixed with approved make of water proofing compound mixed asper manufacturer's specifications as 1st coat and leaving the surface rough.Apply 2nd coat of 6 mm thick of CM 1:4 and finishing the surface by rubbingwith sponge till uniform texture is obtained. Rate shall include providingnecessary scaffolding, GI weld mesh at all joints of brick and concrete surfaces,with a minimum overlap of 150 mm in all directions and curing complete.

SQM 166

80 SMOOTH CEMENT PLASTER FOR CEILING/CHHAJA Providing and applying 6 mm thick plaster in CM 1:3 to ceiling and bottom surface of chajja using screened sand including finishing smooth and providing drip moulds at chajja edges, scaffolding and curing etc. complete.

SQM 114

81 SMOOTH CEMENT PLASTERING (INTERNAL WALL) Providing and laying 12mm thick smooth cement plastering in 1:4 CM in single coat to all the interior walls including providing necessary scaffolding, GI weld mesh at all joints of brick and concrete surfaces, with a minimum overlap of 150 mm in all directions and additional thickness if required to achieve perfect line and level without any extra cost.

SQM 130

82 CERAMIC TILE FLOORING - Providing and laying matt finish 1st quality Ceramic tiles of 8 mm thick of following size in flooring of approved make and shade and free from cracks, warpage,fissures and flakes with straight edges and perfect corner laid at right angle as per design and pattern over a bedding of cement mortar of average 30 mm thick CM 1:5 finishing the joints neatly with white cement mixed with matching colour pigment and finish in all respect and all material and labour complete.

83 300mmx300mm SQM 74084 400mmx400mm SQM 792


85 CERAMIC TILE SKIRTING: Ceramic tile skirting 100mm in height using C. M. bedding 1:3 & fixed with neat cement slurry. Rate to include all necessary chipping of brick masonry / concrete so that skirting is projecting uniformly 6mm from plaster thickness. All vertical joints of skirting shall match with floor tile spacing uniformly as per standard specifications and EIC directions.

RMT 123

86 POLISHED VITRIFIED CERAMIC TILE FLOORING -Providing and laying 1st quality polished vitrified Ceramic tiles of 8 mm thick of following size in flooring of approved make and shade and free from cracks, warpage,fissures and flakes with straight edges and perfect corner laid at right angle as per design and pattern over a bedding of cement mortan of 30 mm thick CM 1:5 finishing the joints neatly with white cement mixed with matching colour pigment and finish in all respect and all material and labour complete.

87 400mmx400mm SQM 200088 VITRIFIED CERAMIC TILE SKIRTING: Ceramic tile skirting 100mm in height

using C. M. bedding 1:3 & fixed with neat cement slurry. Rate to include all necessary chipping of brick masonry / concrete so that skirting is projecting uniformly 6mm from plaster thickness. All vertical joints of skirting shall match with floor tile spacing uniformly as per standard specifications and EIC directions.

RMT 259

89 GRANITE flooring Providing and laying 19 mm thick granite slabs of sizes telephone black colour, free from cracks, warpage, fissures and flakes with straight edges and perfect corner laid at right angle as per design and pattern over a bedding of 30 mm thick 1:5 cement mortar and neat cement slurry, finishing the joints neatly with white cement mixed with matching colour pigment and finish in all respect and all material and labour complete.

SQM 2984

90 IPS FLOORING Providing mixing and laying 50 mm thick Indian Patent Stone flooring in PCC 1:2:4 mix concrete with 12 mm and down size graded crushed aggregate including providing and fixing 4 x 25 mm size glass strips in 1 metre x 1 metre panels, casting the concrete compacting and finishing the surface smooth using cement slurry.

SQM 276

91 GRANITE flooring Providing and laying 19 mm thick granite slabs of sizes other than telephone black but of approved colour by HPCL, for flooring and sill, free from cracks, warpage, fissures and flakes with straight edges and perfect corner laid at right angle as per design and pattern over a bedding of 30 mm thick 1:5 cement mortar and neat cement slurry, finishing the joints neatly with white cement mixed with matching colour pigment and finish in all respect and all material and labour complete.

SQM 3328

92 GRANITE SKIRTING Providing and fixing 19mm thick granite skirting of colour & shade as per HPCL 100 mm height free from crack fissures & flakes with straight edges & perfect corners fixed at right angles with neat cement paste and finishing the joint with white cement mixed with matching colour pigment. The skirting shall project only 10-12 mm from the wall and job includes chipping the wall for fixing the skirting and making good the same after fixing the skirting.Rate to include beveling of top surface and polished to the satisfaction of EIC.

RMT 318

93 CERAMIC TILES DADO IN TOILET: Providing and fixing ceramic tiles of size of approved shade and make First quality , free from crack fissures & flakes with straight edge s & perfect corners fixed at right angles as per the design and pattern, including applying 12mm thick backing plaster in 1:4 CM and fixing the tiles with neat cement paste , and finishing the joints with white cement mixed with colouring pigments to match the colour of tiles properly cured & finished in all respects, etc complete

94 200X300 mm SQM 92995 300X400 mm SQM 965


96 19MM THICK GRANITE CLADDING FOR CURTAIN WALL Providing and fixing machine cut and polished telephone black Granite slab of thickness of 19 mm selected & sorted for uniformity in colour, free from cracks, fissures and flakes with straight edges and perfect cornors using 50mmx20mmx3mm SS T shaped cleats of 100mm long . The cleats are fixed over the wall with M12x100mm long GI fasteners by providing 2 nos 12mmx25mm size slots and drilling the wall. Rate to include making necessary grooves in granite slab , finishing the joints neatly with white cement mixed with coloring pigment to match color, polished and finished in all respect, all materials and labour complete.

SQM 2989

97 KOTA STONE Flooring Providing and 20mm thick Kota stone flooring with 25mm bedding CM 1:3, cement slurry and machine polishing etc complete. 300mm x 300 mm

SQM 628

98 KOTA STONE FLOORING Providing and fixing 20 mm thick 600MMX600MM size Kota stone flooring with 25mm bedding CM 1:5, cement slurry and machine polishing etc. complete.

SQM 713

99 KOTA STONE STEPS Providing and fixing 20 mm thick one piece Kota stone slabs with 25mm bedding CM 1:3, cement slurry and machine polishing including nosing etc . complete

SQM 694

100 SILL SLAB Providing and laying 20 mm thick machine cut & machine polished telephone black granite strips over a bedding of 20 mm thick 1:5 CM for window sills. The strips shall be of single piece only as per width of window wall and project 12 mm beyond the face of the wall.

SQM 2905

101 EUROCON TILE FOR WALK WAY Supply and fixing concrete tile of EUROCON make approved shade of 20mm thickness for flooring including providing 20mm thick 1:5 cement mortar bed and a floating coat of neat cement slurry, finishing the joints with white cement mixed with matching colour pigment, cleaning the surface with dilute sulphuric acid etc. Complete. Basic rate of tile not lower than Rs. 500/sqm

SQM 1317

102 Same as above item 22 but for treads and risers Basic rate of tile not lower tha Rs. 400/sqm

SQM 1312

103 WATER PROOFING104 TERRACE WATER PROOFING Providing and laying integral cement based

water proofing of average 100 mm thick as per specifications given below: - cleaning RCC slab and applying neat cement slurry mixed with waterproofing compound. - providing and laying brickbat coba in CM 1:4 mixed with water proofing compound and curing for a period of 24 hours. - laying of 25 mm thick PCC 1:1.5:3 mix with 6 mm and down size coarse aggregate and water proofing compound, finishing smooth , making half round vata at the junction of parapet wall and slab and curing for 10 days.

SQM 392

105 Water proofing on top of chhaja with 25mm thick PCC 1:1.5:3 with 6mm and down size stone aggregate mixed with water proofing compound, finishing smooth, making half round vata at the junction of chhaja and wall, curing etc. complete.

SQM 201

106 WATER PROOFING BY BITUMEN FELT Water proofing with bitumen felts as per specifications (Bitumen of Shalimar or equivalent make as approved by EIC)- Scrapping, removing old bituminised surface, if any, by chisel, etc, cleaning the surface thoroughly with wire brush and duster and providing water proofing as per specification. Applying one coat of bitumen primer, applying hot bitumen 30/40 @ 1.2kg/SQM. Supplying and laying bitumen felt conforming to IS:1322 in lengths at right angles to the direction of the run of the gradient, starting at the lowest level and overlap of 75mmfor adjacent layers,overlap at end of strip of felt should be 100mm. Parapet joints to be suitably fillated and the feltto to be taken upto a minimum heuight of 225mm on the parapet. Scope of job includes breaking of parapet plaster upto min 225mm making chases before the felto and finally plastering the surface upto the felto height.

SQM 373

107 PAINTING


108 WHITEWASH Providing and applying 3 coats of white wash to plastered and concrete surfaces including providing necessary scaffolding, surface preparation , mixing DDL binder, blue etc. complete as per IS: 712- Latest Edition. If additional coats are required to obtain uniform and smooth finish, the same shall be carried out at no extra cost.

SQM 17

109 OIL BOUND DISTEMPER Providing and applying 2 coats ( first coat with brush and final coat with Roller) of OBD of approved make and shade on all surfaces and heights to give an even shade including primimg coat and full putty after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth etc., all material and labour complete

SQM 89

110 ACRYLIC EMULSION PAINT (INTERIOR GRADE) Providing and applying 2 coats ( first coat with brush and final coat with Roller) of Acrylic Emulsion paint of approved make and shade on all surfaces and heights to give an even shade including primer and full putty after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth etc., all material and labour complete

SQM 125

111 ACRYLIC EMULSION PAINT (EXTERIOR GRADE) Providing and applying 2 coats of acrylic anti fungal cement paint including primer of BERGER (Weathercoat) or approved equivalent make and shade to all the exterior surfaces over a coat of primer as per manufacturer's specifications including providing necessary scaffolding, curing , etc. complete. If additional coats are required to obtain uniform finish, the same shall be carried out at no extra,cost as directed by Engineer In Charge.

SQM 136

112 WATER PROOF CEMENT PAINT Providing and applying 2 coats of water proof cement paint of approved make and of required shades on all surfaces and heights to give an even shade after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth etc., all material, scaffolding and labour complete.

SQM 51

113 SANDTEX MATT Providing and applying 2 coats of Sandtex matt paint of approved make and of required shades on all surfaces and heights to give an even shade including a primer coat of snowcem plus after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth etc., all material, scaffolding and labour complete

SQM 103

114 SYNTHETIC ENAMEL PAINT OVER WALL Providing and applying 2 coats of synthetic enamel paint 1st quality of approved manufacturer and of required shades on wall to give an even shade including a primimg coat after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth etc., all material , scaffolding and labour complete

SQM 87

115 SYNTHETIC ENAMEL PAINT OVER STEEL SURFACE Providing and applying 2 coats of synthetic enamel paint 1st quality of approved manufacturer and shades on steel surface to give an even shade including two coats of zinc phosphate primer after thoroughly brushing the surface free from rust and other foreign matter and also including preparing the surface even and sand papered smooth etc., all material and labour complete

SQM 99

116 Providing and fixing MS grill fabricated from MS flat/square bar as per approved design including painting with two coats of zinc phosphate and two coats of synthetic enamel paint.

KG 65

117 Providing and fixing MS ladder fabricated from MS angle and plain rod as per approved design including painting with two coats of zinc phosphate and two coats of synthetic enamel paint.

KG 58

118 DOORS, WINDOWS, VENTILATORS


119 ALUMINIUM GLAZED DOOR/ FIXED GLAZING WITH 12MM GLASS: Providing and fixing Aluminium glazed door/ fixed glazing with 20 micron powder coated of colour of HPCL choice with aluminium section minimum wall thickness of not less than 2 mm with extruded built up section of approved make and weight ratio joints mitred ad joint with heavy duty aluminium pressure die cast cleats with fins to match the section of frames conforming to approved section and shutter conforming to approved sections and glazed with 12 mm thick glass fixed to shutter with aluminium snap beading and neoprene / PVC gaskets/CP brass/stainless steel screws and fixed to the wall with requisite rawl plugs and screw or with fixing clips or with expansion hold fastners including necessary filling up of gaps at junctions, at top , bottom and sides with requisite PVC/neoprene felt/polysulphide sealant/sillicon sealant etc all complete as per architectural drawing. Aluminium anodised shop front ( Doors & fixed glazing ) with frames at top & bottom and at two ends of INDAL make with section no. 9205 of size 101.5 x 44.45x 3 with weight of 2.342 kg/m or of nearest sections availabe of other approved make. Round acrylic handle and locking arrangement to be provided for main door.

SQM 4753

120 HYDRAULIC FLOOR SPRINGS Providing and fixing double action hydrauclic floor springs of approved brand ( HARDWYN/EVERITE) conforming to IS:6315 for aluminium doors. Rate to include cutting of floors as required, embeding in floors and cover plates etc complete as per specifications.

NOS 2913

121 ALUMINIUM PANELLED DOOR Providing and fixing 20 micron colored powdercoated single leaf aluminium door with minimum wall thickness of not less than 2 mm , joints mitred ad jointed with heavy duty aluminium pressure die cast cleats with fins to match the section of frames conforming to INDAL section 9221 or equivalent section( Jindal/HIndalco)and shutter conforming to INDAL section 9200, 9201, 9202 and 9240 or equivalent section (Jindal/Hindalco) , fully panelled with 9 mm thick prelaminated 3 layers midium density ( exterior grade) particle board Grade-1, type -II conforming to IS:12823 bonded with phenolformaldehyde synthetic resin of approved brand and manufacturer fixed to shutter with aluminium snap beading and neoprene / PVC gasket / CP Brass /stainless steel screws fixed to the wall with requisite rawl plugs and screw or with fixing clips or with expansion hold fastners including necessary filling up of gaps at junctions, at top , bottom and sides with requisite PVC/neoprene felt/polysulphide sealant/sillicon sealant etc all complete as per architectural drawing.

SQM 3790

122 Aluminium door section of INDAL make or equivalent make with the following section : Main frame on all sides - 9221 -101.5 x 44.45 x 2.5 of weight 1.975 kg/mtr Shutter vertical frame- 9202 - 50 x 44.5 x 2.5 of weight 1.202 kg/mtr. Shutter top frame - 9201-50x44.5x2.5 of weight 1.299 kg/mtr Shutter middle frame - 9129-50x45x2.5 of weight 1.292 kg/mtr Shutter bottom frame - 9200-100x44.5x2.5 of weight 1.974 kg/mtr Door handle -5140 - 100x 30 x 2.5 of weight 0.988 kg/mtr Glazing clip - 4660 - 17.8 x 17.6x 1.3 of weight 0.169 kg/mtr

123 ALUMINIUM WINDOWS


124 ALUMINIUM WINDOWS (OPENABLE) Providing and fixing 20 micron colour powder coated aluminium glazed windows with 4 mm glass & extruded built up section of wall thickness not less than 1.5 mm and approve make with glass panel fixed to side -hung shutter with aluminium snap beading and neoprene / PVC gasket / CP Brass /stainless steel screws fixed to the wall with requisite rawl plugs and screw or with fixing clips or with expansion hold fastners including necessary filling up of gaps at junctions, at top , bottom and sides with requisite PVC / neoprene felt / polysulphide sealant/sillicon sealant including heavy duty handle cum locking arrangement etc all complete as per architectural drawing and the direction of Engineer In-charge. Aluminium door section of INDAL make or equivalent make with the following section : Outer frame - 2082 -34 x 44.45 x 28.5x 2 of weight 0.554 Kg/mtr Shutter frame- 4124 - 34 x 44.5 x 28.5x 1.5 of weight 0.494 kg/mtr Mullion -9139- 57 x 34 x 25x2 of weight 0.810 kg/mtr Cleat angle - 2081 - 50 x 50 x 4.9 of weight 1.177 kg/mtr Glazing clip : 4125 - 31x 17.5 x 1.2 of weight 0.184 kg/mtr

SQM 3608

125 Aluminium sliding windows same as above SQM 3392126 ALUMINIUM LOUVRED VENTILATOR Providing and fixing colour powder

aluminium ventilator with extruded built up section of wall thickness not less than 1.5 mm and approve make glazed with 4 mm thick opaque glass louver 100mm wide .Outer frame - 2082 x 34x 44.5 x 28.5 x 2 of weight 0.554 kg/mtr Mullion - 9139 - 57 x 34x 25 x 2 of weight 0.810 kg/mtr Cleat angle - 2081- 50 x 50 x 4.9 of weight 1.177 kg / mtr Glazing clip- 4125- 31 x 17.5 x 1.2 of wt. 0.184 Kg/mtr Bottom 900mm height shall be with 9mm thick both side prelaminated NOVOPAN board. The door shall be provided with aluminium handle, towerbolt, locking arrangement etc. complete.

SQM 2506

127 STEEL WINDOWS Supply, fabrication and fixing of MS glazed windows using approved Z sections with 4mm plain glass including providing grill with 12mm sqare bar @100mm c/c , painting with two coats of Zinc Phosphate primer and two coats of synthetic enamel paint, handle , stay arrangement etc. complete.

SQM 2689

128 ROLLING SHUTTER Supply, fabrication and fixing of MS rolling shutter of the following specifications including grill window of 300 mm height at eye level for visibility even in closed position. Code: Conforming to IS 6248 – 1979 Type: Self Coiling type (manual) Curtains: Interlocking cold rolled lath section of 0.8 mm thickness. Lock plate : MS sheet of 3.15 mm thick reinforced with MS angles of 35 x 35 mm. Guide channel : MS sheets of 3.5 mm thick Bracket Plate : MS Sheet of 0.9 mm thick Hood Covers : MS sheet of 0.9 mm thick Locking handle : To be provided suitably. Rate shall include providing and fixing holdfasts and painting two coats of enamel paint of approved make and shade over two coats of zinc phosphate primer.

SQM 2106

129 Grill in rolling shutter: Supply , fabricationand fixing of manually , operated steel rolling net shutter as per the specifications. Nets to be in hexagonal pattern, the round MS bars used for jolly should be in 8 mm in dia, all other specifications as per the item for rolling shutter as above.

SQM 2271

130 MISCELLANEOUS131 Providing & fixing MS fan hooks with 16 mm dia MS bar bent to shape with

hooked ends in RCC Slab during laying including painting the exposed portionNos 77

132 MORTICE LOCK : Providing & fixing GODREJ or equivalent make six lever lock ( Cylindrical/ Round Head ) including all necessary hardware etc.

NOS 1259

133 DOOR CLOSER : Providing and fixing door closer of Hardwin/Everite make size no. 2

NOS 1415

134 STRUCTURAL STEEL WORK FOR SERVICE BAY


135 Supplying, erecting and fixing in position Pre-fabricated structures at all elevations for service bay using structural steel sections conforming to IS:2062, including cutting, welding or bolting, supply of bolts/nuts/washers etc., complete as per drawings including surface preparation and applying one coat of zinc phosphate Primer before erection and two coats of synthetic enamel paint as per specification after erection and all materials and labour complete. (No welding is permitted at site). The rate quoted shall include cost of bolts, nuts, washers, welding and electrodes and any other consumables required for completeing the work.

MT 64505

136 Supply, erection and fixing of corrugated non asbestos Poly Propelene based cement sheet (PC sheet) 6mm thick of Everest make grey colour or approved equivalent for service bay including supply and fixing of bitumen/ GI washer, J bolt etc.,

137 For Roof SQM 528138 For Side sheet including gable end SQM 570139 GYPSUM BOARD FALSE CEILING Providing and fixing Gyp board false ceiling

with required accessories INDIA GYPSUM make including painting with two coats of plastic emulsion paint

SQM 826

140 Supply, fabrication and erection of Ornamental Cast Iron stairway as per approved design, section etc. Including treads, riser, baluster, MS ball, toop landing chequered plate etc., complete. Rate per step

NO 3783

141 PLUMBING AND SANITARY WORK142 WATER CLOSETS143 WATER CLOSETS EUROPEAN TYPE Supplying and fixing Ivory colour

vitreous china European type water closet comprising of the the following accessories including cutting and making good the walls & floors wherever required compleste as directed by Engineer In Charge A) Coloured ( pastel colour) viterous china pedestal type European water closet with P or S trap of Hindware sanitaryware standard model or equivalent approved make as per the direction of Engineer In Charge. B) 15mm NB brass angle valve of approved brand as per the direction of Engineer In Charge C) 15 mm NB CP inlet connection with Brass unions at the ends. D) Commander make or equivalent matching colour polypropylene seat cover with necessary brass hinges and rubber bushes etc E) WC connector with neoprene rubber etc F) 10 litres capacity low level plastic cistern of matching colour parry slimline make or approved equivalent with necessary fittings, brackets, screws, etc all complete.

NOS 5971

144 INDIAN WATER CLOSET Supplying and fixing Ivory colour vitreous china Orissa Pan type water closet comprising of the the following accessories including cutting and making good the walls & floors wherever required complete as directed by Engineer In Charge A). Coloured (pastel colour) viterous china 580 mm orissa pan water closet of Hinduatn sanitaryware or any equivalent make with P or S trap B) 10 litres capacity hi-grade engineering plastic low level flushing cistern of matching colour parry slimline make , model no 8068 or approved equivalent make with necessary fittings, brackets , screws etc. all complete C) 32 mm PVC flush pipe 10Kg/sq.cm quality of approved length with necessary fittings, clamps etc D) 15 mm NB CP inlet connections with brass union at the ends E) 15mm NB brass angle valve as per ISI of approved brand as per the direction of Engineer In Charge F) WC connector with neoprene rubber

NOS 3788

145 URINALS Supplying and fixing Ivory colour viterous china flat back urinal of size 300mmx400mm with integrated overflow of Hindustan Sanitary or equivalent approved make with CP flush valvre, cp pipe connection, CP waste coupling , CP Brass bottle trap, 32 mm PVC waste line of required length etc. all complete all of approved make and as per the direction of Engineer In Charge

NOS 5404


146 URINAL DIVISION PLATE Providing and fixing 1200 x 450 x 20 mm size telephone black granite partition plate between urinals including cutting masonary/concrete surface to required size, fixing the division plate on the ceramic tiles by means of SS clamps, nuts & bolts, polishing all exposed surface etc all complete as directed by Engineer In Charge.

NOS 2461

147 HAND WASH BASIN Providing and fixing ivory coloured wash basins of size 550 x 400 without pedestal Including the following accessories: -15mm brass CP ,stop cock -1 No .-15mm CP connections from the above stop cock to pillar cock - 1 No. -32mm dia waste coupling, CP brass chain and rubber stopper. -30mm bottle trap with cleaning eye, extension piece and wall flange. -Providing and fixing brass CP 13mm half turn pillar cock. Rate to include supply, painting and fixing of necessary CI brackets with nuts and bolts and fixing the wash basin with all necessary connections in walls, All fittings are of approved make.

NOS 4213

148 MIRROR : Providing and fixing bevelled edge mirror of superior glass of 5.5 mm thick & 600 x 600 mm size of BELGIUM GLASS or any other equivalent make, 3mm thick felt backing or 6 mm asbestos sheet or with wooden beads allround of specified size and fixed with wooden plugs with CP brass screws and cup washers etc all complete as directed by Engineer In Charge

SQM 1199

149 SOAP TRAY Providing and fixing readymade CP brass soap tray near wash basin with CP brass screws of approved make.

NOS 522

150 TOILET PAPER HOLDER Supplying and fixing of 150 x 150 mm pastel coloured toilet paper holder of Hindustan Sanitary ware or equivalen approved make at required position and elevation as directed. Rate to include making good the chases in walls after fixing the above.

NOS 522

151 TOWEL RAIL Providing and fixing CP brass towel rail mounted on walls. Including all accessories, fixed and anchoring etc. complete as directed of approved make.

NOS 994

152 TOWEL RING Providing and fixing CP brass towel ring mounted on walls including all accessories, fixed and anchoring etc. complete as directed of f approved make.

NOS 792

153 STOP COCKS AND BIB COCKS Providing and fixing in position CP brass stop cocks and bib cocks of heavy type ISI marked of approved make

154 15mm dia stop cocks NOS 793155 15mm dia bib cocks NOS 842156 CONCEALED GI PIPING - Providing & fixing following size medium grade GI

pipes of TATA/ JINDAL make conforming to IS-1239 concealed in the walls and under the concrete floors including making chases in the walls or concrete floors,fixing with clamps at every 1m c-c, necessary tees, bends, elbows, plugs, nipples, unions, testing of pipelines for leaks upto a pressure of 6 Kg/sq cm , painting the pipes with hot bitumen, wrapping the pipes with hessian cloth and making chases of the walls good after piping complete.

157 15 mm nominal bore RMT 207158 20 mm nominal bore RMT 237159 EXPOSED GI PIPING Description same as above but Providing, laying and

fixing GI medium grades pipes in open on brick or RCC surface with the help of MS 'U' clamps at every 1 m and at every turn.

160 15 mm nominal bore RMT 195161 20 mm nominal bore RMT 237162 25 mm nominal bore RMT 273163 Providing & fixing 25mm dia size brass full way gate valve ISI marked and

approved make 164 25mm dia NOS 1193165 15mm dia NOS 890


166 WATER TANK Supplying and installation of HDPE water tanks Sintex / Fusion / Polycon make of 1000 litre capacity including 300 mm high brick masonry pedestal of 230mm thick in CM 1:6, providing 75mm thick RCC 1:2:4 slab with reinforcement 8mm tor @150mm c/c, lifting the tank , making all necessary GI connections to inlet, outlet, and overflow nozzles and cleaning the tank before commissioning.

NOS 7223

167 WATER TANK Same as above - 2000 Lts. NOS 13822168 PVC SOIL / WASTE /RAIN WATER PIPES - Supplying and laying the

following size PVC pipe of 4KG/sqcm pressure rating including plain or door type bends, shoes, offsets, clamps junctions, tees, etc, complete .

169 160 mm dia RMT 572170 110 mm dia RMT 369171 80 mm dia RMT 240172 NAHANI (FLOOR) TRAP Providing and fixing PVC floor trap of self cleansing

design conforming to IS specs with 100mm inlet, 75mm outlet and 150mm CP hinged grating of 6mm thick with rim. Rate shall include making all necessary leak proof connections etc .

NOS 411

173 STONE WARE PIPES Providing and laying 150mm dia. salt glazed stoneware pipes conforming to IS 651 Grade-A including bends, tees etc, excavation of trenches, 100 mm thick PCC 1:4:8 bedding, providing PCC 1:2:4 haunches @ 0.5mc/c , filing the joints with tarred gasket, plastering with 1:3 cement mortar smoke testing of joints,backfilling the trenches with excavated earth, watering, ramming etc., complete.

RMT 328

174 GULLY TRAP WITH CHAMBER Providing and fixing square mouth gully trap including constructing 300 X 300 MM internal size brick masonary chamber with 230mm thick brick masonary in 1:5 cement mortar, excavation, 75mm thick PCC 1:4:8 bed, plastering with neat cement finish, Medium duty CI cover with frame etc. Complete.

NOS 1867

175 Providing and constructing following size inspection chambers with 230mm thick brick masonary in 1:5 cement mortar, excavation, 75mm thick PCC 1:4:8 bed, plastering with neat cement finish, Medium duty CI cover with frame etc. Complete.

176 600 x 600 mm (Internal dimensions) with 600 mm depth NOS 5592177 450 x 450 mm (Internal dimensions) with 600 mm depth NOS 4637178 SEPTIC TANK Prpoviding & constructing septic tank of size

1200x2000x1800mm depth with excavation ,PCC1:4:8 100mm thick bed , 345/230mm thick brick masonary wall in CM 1:5 ,RCC1:2:4 100mm thick slab with 8mm tor steel @150c/c both way , 115mm thick baffle wall with RCC beam at bottom ,12mm thick smooth cement plaster with water proofing compound inside and exposed outside portion, providing 600mmx600mm size medium duty CI cover, providing 75mm dia PVC vent pipe etc. Complete.

NOS 29434

179 SOAK PIT Providing and constructing soak pit of 2.5m dia (internal) and 2m depth as per drawing.

NOS 19757

180 POINT WIRING FOR LIGHT/FAN WITH MODULAR PLATE SWITCHES ANCHOR ROMA/MK /LEGRAND Providing and laying point wiring in concealed conduits for the following points using specified 1100V grade PVC insulated,FRLS multistranded 3 x 1.5 sqmm copper conductor wires. Rate to include supplying, laying and securing in position in roof slabs and brick walls or concrete columns 25 mm dia rigid PVC conduits of approved make with necessary accessories and junction boxes/pull boxes. Providing and fixing in the brick walls flush type metal switch boxes of approved make shade and sufficient size to accommodate all 6A Modular switches / 3 pin socket, screws, holders. ceiling roses and the fan regulator wherever required. Rate to include wall chasing and rough plastering. Providing and fixing single pole 5A modular plate switches of MK or ANCHOR ROMA make of approved colour . One switch shall be provided for each light and fan point. Rate to include providing main circuit wiring from DB to switch boards with 2.5 sqmm copper wire also

NOS 615


181 Same as above but for 5A socket controlled by one 5A switch on the same lighting board

NOS 437

182 Same as above but for 5A socket controlled by one 5A switch independently mounted including providing wiring with 3 runs of 1.5 sqmm pvc insulated copper wire through PVC conduit

NOS 515

183 Same as above above but for 5/15A socket controlled by 15A switch independently mounted including providing wiring with 2 runs of 2.5 sqmm and 1 run of 1.5 sqmm PVC insulated copper wire through PVC conduit

NOS 681

184 Same as above above but for for AC point with 2 runs of 4 sqmm (P&N)and 1 run of 2.5 sqmm (earthing) PVC insulated , FRLS multistrand copper cable in 25 mm dia PVC conduict from MCBDB to 20 A powersocket. The conduit shall be partly/fully concealed in all types of wall, ceiling etc complete with all accessories, wiring, termination, connected civil works, rough plastering etc including supply and fixing of 20A industrial socket controlled by 20A SPMCB of approved make.

NOS 2012

185 Supply, laying , and commissioning of wiring using following sizes of PVC insulated , FRLS, unsheathed, multistraned copper wire drawn in PVC conduits. Rate to include supply of 16 GI fish wire, conduicts & accessories, wiring, terminations etc complete .

186 4 runs of 10 sqmm and 1 run of 6 sqmm copper wire in 40 mm dia PVC conduit from panel to Distribution boards.

RMT 394

187 4 runs of 6 sqmm and 1 run of 4 sqmm copper wire in 32 mm dia PVC conduict from panel to Distribution boards.

RMT 261

188 CEILING FANS Supplying and fixing of the ceiling fans of approved make with detail as below : Sweep :48" Colour :white Bearing type :Double ball bearing Down rod :clear 300 mm long Regulator : Electronic type ANCHOR ROMA/MK Accessories :Screws, wall nuts etc.

NOS 2125

189 EXHAUST FANS190 Supply, fixing and commissioning of Exhaust fans including bird louvers, frame

works and other civil works like chipping and making the surface good etcT

191 305 MM DIA NOS 2623192 230 MM DIA NOS 2265193 LIGHT FIXTURES Supply, fixing and commissioning of following light fittings.

Rate to include all accessories, interconnection of wires from ceiling rose to the fittings and lamps, copper choke etc. complete.

194 1 x 36 W tube light fitting with lamp of approved make . NOS 1273195 1 x 60W spot light luminaire with 1 meter track including lamp of approved

make. for display shelving NOS 1554

196 1 x 60 W Bulk head luminaire including lamp of approved make ( Outside building).

NOS 430

197 Angle holder Anchor make including lamp 60W (Toilets). NOS 48198 1 x 36 W tube light fitting including lamp of approved make ( stores, service

area)NOS 878

199 2 x 36 W tube light fitting including lamp of approved make (for false ceiling area)

NOS 2877

200 TELEPHONE SOCKET POINT Supply and laying 2 pairs of 0.5 mm dia screened and shilded telephone wire in 20 mm dia PVC conduit partly/fully concealed in types of walls , floor etc complete with all accessories , wiring terminations, connected civil works, rough plastering etc including supply of 16 GI fish wire conduit & accessories etc.

RMT 43

201 Supply, fixing and commissioning of 5 pairs of telephone tag block of Krone type enclosed in suitable MS box. Rate shall include all accessories, connected civil works for fixing the same as per specifications.

NOS 1341

202 Supply and installation of modular type telephone socket MK make in a suitable size box concealed to wall including all civil works

NOS 403

203 PART C EXTERNAL ELECTRIFICATION


204 Supply and fixing of wall mounting type meter board made out of 16 SWG CRCA sheet steel and single iron with 3 nos 200A Fuse cutouts N.L, 1 no earth link , 1 no neutral link and space for accommodating 1 no. 3 ph, 4 wire KWH meter complete with adequate size of copper wire interconnections, powder coating etc. Complete.

NO 14118

205 Supply and erection, testing commissioning of floor mounting type cubical panel board made out of Structure 14 SWG & Door 16 SWG CRCA sheet steel with 300 A TPN copper bus bars, interconnections, earthing, powder coating and comprising of the followings as required. TYPE - I.Incomer : 2 nos 125A TP switch fuse unit with HRC fuses for DG and EB, 1 no 125A TP on line change over switch 2 no volt meter with volt meter selector switch, 2 no ammeter with C T & ammeter selector switch, 2 sets of Phase indicating lamp (RYB) Outgoings : 3 nos 63A and 6 nos 32A TP fuse switch unit with HRC fuse 10KVAR capacitor : 1 nos

NO 152096

206 Supply and erection, testing commissioning of floor mounting type cubical panel board made out of Structure 14 SWG & Door 16 SWG CRCA sheet steel with 200 A TPN copper bus bars, interconnections, earthing, powder coating and comprising of the followings as required. TYPE -II.Incomer : 2 nos 125A TP switch fuse unit with HRC fuses for DG and EB 1 no 125A 4 pole change over switch ( on line) 2 no volt meter with volt meter selector switch, 2 no ammeter with C T & ammeter selector switch, 2 sets of Phase indicating lamp (RYB) Outgoings : 2 nos 63A and 4 nos 32A TP fuse switch unit with HRC fuse 10 KVAR capacitor : 1 no

NO 108000

207 Same as above but with following details TYPE III Incomer : 2 nos 63A TP switch fuse unit with HRC fuses for DG and EB 1 no 63A 4 pole change over switch (on line) 2 no volt meter with volt meter selector switch, 2 no ammeter with C T & ammeter selector switch, 2 sets of Phase indicating lamp (RYB) Outgoings : 1 no 63A and 3 nos 32A TP fuse switch unit with HRC fuse 5 KVAR capacitor : 1 no

NO 88000

208 Supply, installation and commissioning of 63A TPN MCB DB Incomer : 1 no 63 A , 4 Pole MCB Outgoings : 18 nos, 10A/16A/20A SP MCBs

NOS 8706

209 Supply, installation and commissioning of 32A TPN MCB DB Incomer : 1 no 40 A , 4 Pole MCB Outgoings : 12 nos, 10A/16A/20A SP MCBs

NOS 6986

210 Phase Selector switch- 63 amps TP (L & T) NOS 7955211 Supply and laying following size PVC insulated, sheathed, armoured cable of

approved make 212 3.5Cx70 sqmm AL cable RMT 531213 3.5Cx50 sqmm AL cable RMT 496214 3.5Cx35 sqmm AL cable RMT 488215 4CX16 sqmm AL cable RMT 273216 4CX6 sqmm AL cable RMT 199217 4CX2.5 sqmm copper cable RMT 216218 3CX2.5 sqmm copper cable RMT 192219 3CX1.5 sqmm copper cable RMT 129220 2CX1.5 sqmm copper cable RMT 105221 End termination of following cable with double compression NFLP gland and

crimping sockets222 3.5Cx70sqmm Al cable NO 362223 3.5Cx50sqmm Al cable NO 303224 3.5Cx35 sqmm AL cable NO 243225 4CX16 sqmm AL cable NO 177226 4CX6 sqmm AL cable NO 150227 4CX2.5 sqmm copper cable NO 144228 3CX2.5 sqmm copper cable NO 137229 3CX1.5 sqmm copper cable NO 124230 2CX1.5 sqmm copper cable NO 98231 End termination of following cable with double compression FLP gland and

crimping sockets232 4CX2.5 sqmm copper cable NO 343


233 3CX2.5 sqmm copper cable NO 310234 3CX1.5 sqmm copper cable NO 251235 2CX1.5 sqmm copper cable NO 198236 YARD LIGHTING237 CABLE TRAY-300 MM WIDE Supply, erection/installation/mounting of 16 SWG

300mm wide perforated GI cable tray inclusive of cable bindingwith suitable GI clamps, GI hooks, GI nuts and bolts complete in the tray in a neat way. The width specified shall be of cable mounting area. Bends at both the sides of cable tray shall be in addition to it.

RMT 775

238 CABLE TRAY -150 mm WIDE : Same as above but for 150m wide RMT 575239 CABLE TRENCH240 Excavation in any type of soil including WBM /asphalt up to 600mm depth and

300mm wide including supply and laying 150mm thick sand on top and bottom of cable, supply and laying bricks laid flat on top, back filling trench etc. Complete.

RMT 258

241 Supplying and fixing NFLP junction box 150mm x150mm x125mm weather proof out door junction box fabricated out of 14 SWG CRCA sheet of IP 54 category of protection with rubber gasket and having locking arrangement including required connector, 10A SPMCB.

NO 455

242 Yard Light pole243 Supply, fabrication, erection of stepped MS medium yard light pole with single

arm of 6.5m height from pedestal as per clause 2.1 and 5.1 of IS 2723 part III and 2713 including providing pedestal of size 0.45mx0.45mx1.2m depth in RCC 1:2:4, excavation, foundation bolt, 450mmx450mmx10mm thick base plate ,painting the pole with two coats of sinthetic enamel paint over a coat of zinc phosphate primer, finishing the above ground portion of pole with 12mm thick plaster etc. complete.

NO 7506

244 Yard light pole same as above but with double arm NO 8428245 Street light fitting.246 Supply of street light fixture of 250 Watts Metal Hallide Light fitting including

lamp single piece die cast aluminium housing complete with all accessories choke, acylic cover etc. complete make WIPRO(WHH 65250), PHILIPS (SGP-401/250) or equivalent suitable for Yard light/Y poles.

NO 6146

247 Supply and Fixing of street light fixture including lamp of CFL 4 x 24W, Bajaj make BT/SFL,424DD/ Crompton make 4x24W-T-S-SHE-414EB/ WIPRO make WFF 12424SGA

NO 5353

248 Fixing of street light fixture including providing flexible wire from junction box to top of the pole

NO 406

249 Providing pipe electrode pipe earthing as per IS 3043 and attached drawing including excavation, supplying 50mm dia GI pipe medium quality, filling the pit with alternate layers of charcoal and salt, back filling, constructing Chamber 400mmx400mx400mm internal size with 230mm thick Brick masonary, providing 12mm thick MS plate cover with 50x50x6 MS angle frame etc. complete.

NO 6371

250 Supply and fixing 10 SWG copper wire for earthing connection to pumps, canopy columns etc.

RMT 89

251 Supply and fixing 25x3 copper flat for earth connection of panel RMT 519252 Providing and fixing 6mm thick MS chequered plate including making holding

arrangements, painting with two coats of zinc phosphate primer and two coats of synthetic enamel paint etc.

KG 56

253 Providing and fixing MS angle/channel supports and edge protection for trench etc. including providing hold fast ,painting with two coats zinc phosphate primer and two coats of synthetic enamel etc.

KG 50

254 Supply and fixing 20mm thick ISI marked rubber mat SQM 1164255 Erection of HPCL supplied yard light pole including providing pedestal of size

0.45mx0.45mx1.2m depth in PCC 1:2:4, excavation, 16mm dia foundation bolt, with two coats of sinthetic enamel paint over a coat of zinc phosphate primer, finishing the above ground portion of pole with 12mm thick plaster etc. complete.

NO 2561


256 Providing plate electrode type earthing as per IS 3043 and attached drawing including excavation supplying 600*600*6.3 mm thick GI plate, 50mm dia GI pipe medium quality, filling the pit with alternate layers of charcoal and salt, back filling, constructing Chamber 400mmx400mx400mm internal size with 230mm thick Brick masonary, providing 12mm thick MS plate cover with 50x50x6 MS angle frame complete.

NO 7429

257 Earthing Pit-Pipe Electrode without chamber:Same as ABOVE item but without chamber and covers. The item isfor providing earthing pit under driveway. The chamber and cover shall be provided with same specifications as of driveway chambers and as per instructions of Engg.-In-Charge. The driveway chambers shall be paid as per respective item rate.

NO 3690

258 Proding/Fixing of MS name/ID plate for earthing pit including painting etc as per the prevailing norms of IS/BIS / as per the direction of EIC. Size 300mmX200mm and 1.2 mm thick with MS flat/square bar for grouting.

NO 425

259 HOARDING LIGHT QVF 135/70 Supply and fixing Philips make Cat. QVF 135 hoarding light fixture (IP54) with Metal Halide MHN-TD 70W lamp,control gear box, light weight corrosion-resistant pressure die cast housing with universal mounting bracket, allaccessories energy efficient copper ballast, heat resistant toughened glass cover, electronic ignitor, reflector,power factor improvement capacitor etc. complete. Approved equivalent Crompton make Cat. TH 6 MH(DE). Thejob includes fixing the street light fixtures and wiring as approved.297

NO 3970

260 CVT Supply and fixing of constant voltage transformer of aproved make - Logicstat, Blue bird, Sukam, Bhurji ,Numeric or equivalent. Party to furnish manufacturer's test certificate alongwith supply and providewarranty/gaurantte for a period of one year from the date of installation. Rating 500 VA ratingCVT Technical SpecificationsInput Voltage 180 to 260V AC/1 Ph/50±2HzOutput Voltage 220VAC/230VAC±1%Frequency Effect Approx. 1.5% change in output voltage, for 1% change in input frequencyEfficiency 90%, Typical, at full loadCommon-Mode-Noise Attenuation* 1:3000, TypicalNormal-Mode-Noise Attenuation* 1:2500, TypicalOutput waveform SinusoidalTotal Harmonic Distortion 5% (Typical) at 230VAC-Input & full-load changeOutput Voltage Correction 2 cycle (max.) for no load to full load conditionsOver Load protection To be providedOperating Temperature 0ºC to +50ºCOperating Humidity 95% RH, non condensingMetering 0-300v, M.I. meter; Accuracy ± 2% FSD (To monitor output voltage)Environment 0-40°C, 95% RH (non condensing)

NO 4500


261 Supply , installation and commissioning of 1 phase AIR cooled balanced / unbalanced load servo controlled voltagestabiliser of rating 5 KVA (Make - Logicstat / Blue bird / Bhurji / Techno Vision /Numeric or HPCL approved make)including auto / manual control, overload trip relay, low / high voltage cut-off, single phase protector, cost of oil. Rateincludes making input and output connection but excludes supply of necessary cables, lugs and clamping. Party tofurnish manufacturer's test certificate alongwith supply and provide warranty/gaurantte for a period of one from thedate of installation. Detailed specifications are as under:Specifications 1 Phase1. Input Voltage 170 – 270VAC2. Output Voltage 230 VAC3. Operating frequency 50 HZ4. Output Voltage Regulation +/- 1%5. Response time < 3 msecs6. Rate of Correction 12 to 60 V / Sec7. Efficiency > 98%8. Wave form Distortion Nil9. Effect on Power Factor Nil10. Operating Temperature 10 – 60 Degree C11. Duty of operation Continuous at 100%12. Cooling Air CoolingPROTECTIONSUNDER / OVER VOLTAGE REQUIREDOver Load Protection MCBINDICATION

NO 8900

262 Same as above3 KVA NO 6500263 PART D DRIVEWAY264 Supply and filling murrum in 200mm thick layers including levelling with doser,

watering, Compacting each layer with 8/10 MT road roller to obtain field dry density 92% of MDD, Dresing top layer to the required slope, Testing of murum sample for OMC&MDD and testing of field dry density by core cutter for checking compaction. Payment will be made only for compacted thickness

CUM 295

265 RUBBLE SOLING Providing and laying dry trap rubble stone soling 230 mm thick including hand packing, filling the interstices with chips, spalls and binding with grit and selected murrum, watering, compacting by power rolling with 8/10 ton roller complete.

CUM 1090

266 Filling material with GSB (Granular Sub Base) of 30 cm thick:: The GSB shall consists of the following material40 to 53MM Size metal : 40%20 to 40MM size metal 20%10 to 20MM size metal 20%0 to 10MM size metal 20%Job shall include supply and filling GSB materials in two compacted layers of 150 MM each. Payment shall bereleased on the compacted layer provided by the vendor at site. Compaction shall be carriedout only with Vibroroller of required capacity . Contractor has to obtain necessary clerance from HPCL or its autorisedreprensatative for first layer. Only after obtaining the second layer GSB shall be provided. Job includes all mematerial and transporation cost of the required to be completed as per the directions of the HPCL

SQM 320


267 WATER BOUND MACADUM Providing and laying WBM in layers of 75 mm compacted thickness each using well graded stone aggregates of 40 mm to 63 mm size of approved quality. Rate includes speading metals, hand packing, filling the interstices with spalls, chips, and approved quality binder and rolling each layer with 10 MT power roller with simultaneous watering till the metal is bound by the water binder paste to achieve maximum compaction, finishing the surface to proper grade and level. Rate also to include carrying out the following tests on aggregates and test results to be submitted to EIC before use and shall meet the follwoing strength requirements. LA Abrasion value : 40% Flakiness index : 15%

SQM

268 First Layer 75 mm thick SQM 119269 Second Layer 75 mm thick SQM 119270 Third Layer 75 mm thick using 53 to 22.2 mm size stone metal. SQM 119271 Wet Mix Macadam.Providing and laying wet mix macadam base course using

45 mm and down graded aggregates, including mixing , laying and compactingclean, crushed and graded aggregates and granular material premixed withwater to a dense mass on a prepared subbase in accordance with therequirements of specifications, drawings and as directedy EIC.

CUM 1324

272 RCC DRIVEWAY273 Providing and laying 150mm-200 mm thick M-20 ,RCC driveway with 1:1.5:3

nominal mix using 20mm and down size crushed stone aggregates in panels using slotted MS channel shuttering, machine mixing, vibrating with screed board vibrator, pond curing for 14 days, vaccum dewatering, finished with power trowelling. Concreting shall be carried out as per IS 456.Rate shall also include providing approved quality polythene paper below the driveway, constructing horizontal and longitudinal vatas with 1:10 CM for curing, levelling depressions if any in the base with 20mm stone aggregates and stone dust.Proper slope to be provided in driveway for easy draining of rain water. Job shall include cutting grooves 4mm wide and 20mm deep by machine and filling the groove with polysulphide compound, providing 12mm thick Shalitek board in the joints between pre cast cover of pipeline trench or top slab of U/G tank and RCC driveway.

CUM 4967

274 Same as above but without vaccum dewatering and power trowelling CUM 4696275 Same as above but using ready mix with vaccum dewatering and power

trollingCUM 6660

276 Same as above but using ready mix with out vaccum dewatering and power trolling

CUM 4762

277 Providing and laying RCC precast slabs of required size with 1:1.5:3 nominal mix using 20mm and down size crushed stone aggregates including shuttering, mixing, compacting , pond curing for 14 days etc. as per IS 456, transporting from the place of casting . Reinforcent steel shall be paid separately.

CUM 4452

278 STEEL REINFORCEMENT Supplying, fabricating and placing in position TMT reinforcement bar conforming to IS 1786 - Latest edition grade FE 500 as required and directed at site for driveway including cutting, bending, placing in position and tying with 20 SWG binding wire, complete. Quantity shall be measured as per reinforcement drawing and with theoretical weights including all authorized laps, chairs, spacers etc., Unauthorised chairs, spacers and laps will not be measured for payment purpose. Weight of binding wire shall not be considered for payment.

MT 57386

279 ASPHALTING Providing & laying 50 mm compacted thickness premix asphalt carpet and 12.mm thick seal coat (total compacted thickness 62.mm) on top of WBM/WMM surface as per procedure.1)Applying a tack coat of hot 80/100

SQM 334


280 ASPHALT CONCRETE Surface preparation through cleaning of the exposed surface by wire brush to remove the loose sand, pebbles and any inorganic material. Applying tack coat of 80 /100 bitumen @ 9.5 Kg / 10 sq.m. After surface preparation as per above. ( Total Compacted thickness of 112 mm ) a. Providing 75 mm thick BT concrete using 1 cu m of 40 mm hard broken granite metal (metal crushed) with 35 kg 80/100 grade Bitumen and .13 cum of 12 mm hard broken granite aggregate for 10 sq m well mixed in machine mixer in correct proportions including supply of materials Cost of machine mixer, power rolling with 10 MT power roller and all labor charges etc., complete in all respects to the satisfaction of HPCL engineer in charge.b) Providing 25m thick Black top surface using 0.27 Cu.M. of 12mm hard broken granite chips (machine crushed) with 25.00 Kg. Of 80/ 100 grade Bitumen per 10 Sq.M. including cost of machine mixing, power rolling with 10 tonnes power roller and all labour charges etc., complete in all respects of satisfaction of H.P.C.L .c) Providing 12mm thk. Black top seal coat using 0.09 Cu.M. of 6mm hard broken granite chips with 10Kg. Of 80/100 grade Bitumen per 10 Sq.M including sprinkling of sand over the black top, supply of material, machine mixing and

SQM 685

281 Bitumen Bound Macadam:Providing and laying bitumenous bound macadumsurface 100 mm thick after compaction including supplying all materialsspreading 40 mm size trap metal layers and key aggreagates heating andspraying bitumen of grade ISgrade S-65 with penetration 60/70 at the rate of400 kg/100 sqm and compacting after finishing by 6mm thick layer of grit to thesatisfaction of the engineer with a roller not less than 10 MT.

SQM 283

282 BITUMINOUS MACADAM 75mm THICK USING 60/70 GRADE BITUMEN:Providing and laying premix bituminous macadam base course with good qualitystone aggregate mix as follow 20mm = 30%, 12mm=35%,6mm=15%coarse sand 15 % and bitumen 60/70 grade 6% by weight .The aggregate shallbe of quality size and grading as specified and bitumen shall be straight runbitumen of grade 60/70 @ 6 % by weight of total mix . The job includeshot mixing by using mini hot mix plant , transporting mix material and laying thesame to the required level & grade,rolling with power roller of 8 to 10 Toncapacity to achieve required compaction and density all material , labour etc.complete. The macadam course shall be laid in two layers of around equalthickness, each layer shall be rolled and compacted. Tack coat shall be appliedbetween the two layers@ 9.8 kg per 10 sqm.

SQM 447

283 PAVER BLOCK284 PAVER BLOCK Providing and laying approved brand/make 80mm thick cement

coloured paving blocks of M 40 grade over a bed of 50mm thick well compacted river sand bed laid over well prepared sub base to the required line and level including all materials, labour, machinery, transportation etc., paving blocks should have chamfered top edges of not less than 4mm and shall be laid and interlocked with a minimum of 2mm gap which in turn packed with river sand, compacting with plate vibrator etc. Complete. Edge restraint with RCC 1:2:4 will be paid separately.

SQM 682

285 Same as above but with in colour SQM 748286 Same as above - reflective coloured paver blocks SQM 972287 HUME PIPE - Supplying, laying, joining and aligning following size NP2 class

RCC Hume pipes conforming to IS-458 Latest Edition below approach road whereever directed. Rate to include joining with cement mortar, excavation up to required depth and providing and laying PCC 1:2:4 haunching @ 1m c/c . Test certificates from manufacture shall be submitted and approved by EIC before use.

288 300mm NB RMT 972289 225mm NB RMT 731290 150mm NB RMT 580


291 INSPECTION CHAMBER Providing and constructing following size inspection chambers with 230mm thick brick masonary in 1:5 cement mortar, excavation, 75mm thick PCC 1:4:8 bed, plastering with neat cement finish, providing 12mm thick MS plate cover with 35x35x6 angle stiffener and 50x50x6 angle frame .Complete

292 Size - 600mmX600mm internal sizeX 700mm depth NO 6631293 Size - 450mmX450mm internal sizeX 600mm depth NO 5498294 PART E TANK INSTALLATION295 Transportation of service station tanks of 9KL/16KL/22KL form tank facbricators

workshop to the retail outlet site including loading, undloading using crane/Chain pulley etc.

296 Up to 50KM distance rate per tank. NO 5705297 Additional charges for KM beyond 50. Only oneway KM will be considered. KM 45298 EXCAVATION299 EXCAVATION - Up to 4 mtr depth Excavation for foundation upto required

depth below existing ground level in any type of soil except hard rock . Rate to include dressing the sides and bottom, bailing out of water if encountered, shoring, strutting, backfilling after the construction of foundation, compacting by the side of the foundation and disposal of surplus excavated earth within/outside HPCL's premises to an unobjectionable place, as directed by the Engineer in Charge including spreading, watering and compaction, complete

CUM 130

300 Same as above but cutting hard rock by pneumatic hammer and compressor. CUM 670

301 PCC302 Providing and laying PCC 1:4:8 using 40 mm and down size graded stone

aggregates in foundation trenches, including compacting, curing etc. complete.CUM 2795

303 Providing and laying PCC 1:2:4 mix using 20mm down size stone aggregate in foundation trenches, including compacting, curing etc. complete.

CUM 670

304 R.C.C 1:2:4305 Providing and laying RCC 1:2:4, providing steel or plywood shuttering with

propoer supports, removal of form work as per IS code, preparing mix using mechanical mixer, compacting using mechanical vibrator, curing with potable water for 14 days etc., complete. Work shall be carried out as per IS 456 latest edition. Rate shall be excluding reinforcement steel which will be paid separately

306 Bottom Raft CUM 4486307 Top Slab (Rate shall be including providing Polythene paper below the slab,

providing 12mm thick Shalitek board in joints to separate pieces. CUM 4486

308 REINFORCEMENT STEEL WORKS309 Supply, Fabrication and placing in position TMT bars conforming to IS 1786 -

Latest edition grade FE 500 as required and directed at site for driveway including cutting, bending, placing in position and tying with 20 SWG binding wire, complete. Quantity shall be measured as per reinforcement drawing and with theoretical weights including all authorized laps, chairs, spacers etc. Unauthorised chairs, spacers and laps will not be measured for payment purpose. Weight of binding wire shall not be considered for payment.

MT 57386

310 TANK INSTALLATION311 Installaion of HPCL supplied Tanks of following capacity in earth pit /under

driveway including providing holding down arrangement, Hydrostatic testing to pressure of 3.5m water column, supplying & filling with water with necessary 50 mm dia pipe & on successful completion emptying out the water from tank , cleaning & drying the inner surfaces with cloth/ cotton waste etc., doping with two coats tank mastic paint of STP make and hot 30/40 bitumen ( total doping thickness 3mm) ,fixing all fittings as required.

312 22 KL NO 14121


313 16 KL NO 12018314 9 KL NO 9427315 Brick Masonary 316 Providing 345mm thick brick wall with bricks having compressive strength of

minimum 35 kg/sqcm in cement mortar 1:5 (1 cement: 5 coarse sand) in foundation and superstructure, plain or curved including providing necessary scaffolding, raking the joints on both faces, curing for 7 days etc., complete.

CUM 4418

317 SMOOTH CEMENT PLASTERING318 Providing and laying smooth cement plaster of 12mm thick in single coat in 1:3

cement mortar mixed with water proofing compound to interior walls including providing necessary scaffolding, curing etc., Complete.

SQM 115

319 SAND FILLING320 Supply and filling coarse river sand in layers of 200mm thickness inside

masonary pit/ earth pit after tank installation including watering, compaction etc., complete.

CUM 1090

321 Manhole cover322 Supply, fabrication and fixing of manhole cover of size 900x900 mm with

65x65x6 angle frame and 16mm thick MS plate with 50x50x6 stiffener including painting with two coats of zinc phosphate primer and two coats of synthetic enamel paint. Rate is applicable for any size of manhole cover.

KG 52

323 Pump Island324 Construction of pump island 1m wide with 230mm thick brick masonry in CM

1:5, 12mm thick plastering in Cm 1:4 roughened to receive granite tiles including excavation, 75mm thick PCC 1:4:8 , sand filling and constructing the wall 300mm above the finished driveway level and 600mm below the finished driveway level .

RMT 1877

325 Installation of Dipsensing Pumps326 Installation of MONO/DUAL/MPD pumps on pedestal including providing &

fixing MS angle frame 65x65x6 & connecting suctionpipe, electrical, earthing connections to the pump etc. complete.

327 Installation of MONO pumps NO 883328 Installation of DUAL pumps NO 974329 Installation of MPD pumps NO 2164330 Pipe Lines331 Supplying & Laying Heavy duty 'C' Class ERW black steel screwed pipeline

Conforming to IS 1239 (part I) – latest edition to the required slope & alignment with heavy duty MS fittings like elbows, tees including doping pipe line with 1 Coat of zinc phosphate primer and 3 coats of 'Shalimastic – HD THIXOTROPIC of STP cold applied anti corrosive treatment after preparing the surface as per manufacturer specifications. The joints are to be made leak proof by using jointing materials like Litharge, Glycerin, Shellac, holdite . The pipes laid above ground shall be painted with two coats of synthetic enamel over two coat of zinc chromate primer of approved quality and shall be color coded as per instruction of EIC. The pipeline shall be tested at a pressure of 5 kg/sqcm.

332 40mm NB RMT 582333 50mm NB RMT 660334 80mm NB RMT 982335 Supplying & Laying 40 mm 'B' Class ERW black steel screwed pipeline

Conforming to IS 1239 (part I) – latest edition for vent pipes to the required slope & alignment with heavy duty MS fittings like elbows, tees including doping pipe line with 1 Coat of zinc phosphate primer and for concealed/burried portion 3 coats of 'Shalimastic – HD THIXOTROPIC of STP cold applied anti corrosive treatment after preparing the surface as per manufacturer specifications. For exposed portion , two coats of synthetic enamel paint of approved make.

RMT 459


336 Laying of HPCL supplied pipeline to the required slope & alignment with heavy duty MS fittings like elbows, tees including doping pipe line with 3 coats of 'Shalimastic- HD THIXOTROPIC of STP cold applied anti corrosive treatment after preparing the surface as per manufacturer specifications. The joints are to be made leak proof by using jointing materials like Litharge, Glycerin, Shellac, holdite. The pipes laid above ground shall be painted with two coats of synthetic enamel over two coat of zinc phosphate primer of approved quality and shall be color coded as per instruction of EIC. The pipeline shall be tested at a pressure of 5 Kg/sqcm.

337 40mm NB RMT 65338 50mm NB RMT 84339 80mm NB RMT 109340 Supply and fixing ISI marked angular check valve of approved make 341 40mm NB NO 3661342 50mm NB NO 4372343 FILL CAP344 Supply and fixing MS fill cap 80mm dia with locking arrangement including

Godrej 6 lever brass lock NO 674

345 Supply and fixing MS dip cap 40mm dia with locking arrangement including Godrej 6 lever brass lock

NO 602

346 Supply and fixing 40mm NB vent hood in vent pipe NO 407347 GRANITE WORKS:348 Providing and fixing 19mm thick pre polished water cut telephone black granite

slab for pump island top including providing 25 mm thk bed cement mortar 1:5 (1cement: 5 coarse sand), floating cement slurry and finishing the joints with white cement mixed with matching colour pigment, edge polishing (bull nosing) etc., complete.

SQM 2984

349 Providing and fixing 10mm thk. pre polished water cut telephone black granite tiles for pump island dado including providing 12mm thk bed cement mortar 1:4 (1 cement : 4 coarse sand), fixing the tiles with neat cement paste and finishing the joints with white cement mixed with matching colour pigment.

SQM 1439

350 WELDED PIPE LINE:Supplying & Laying 2.5" Dia Heavy-duty 'C' Class MS Steel ERW Welded P/L ( TATA/SWASTIK/JINDAL make)Conforming to IS 1239 (part I) – latest edition to the required slope & alignment with heavy duty MS fittings likeelbows, sockets,unions , tees etc. including doping pipe line with 3 coats of 'Shalimastic HD THIXOTROPIC ofSTP cold applied anti corrosive treatment after preparing the surface as per manufacturer specifications. The jointsare to be made leak proof. The P/L which would laid aboveground shall be painted with two coats of syntheticenamel over two coats of Zinc Chromate primer of approved quality and shade. The pipeline shall be tested at apressure of 5Kg / sqcm.

RMT 1036

351 S/F/L MS C CL.WELDED PL2.0"DIA: Same as above but for 2.0" pipe RMT 982352 FLANGE JOINT 2.5" DIA:Supplying & fixing of 2.5 inches dia C Class MS

Flanges for Petroleum products of approved make and of Heavyduty usage.

EA 1032

353 FLANGE JOINT 2" DIA:Supplying & fixing of 2 inches dia C Class MS Flanges for Petroleum products of approved make and of Heavy dutyusage

EA 959

354 P/F BALL VALVES 2.5" DIA:Supply and fixing ISI marked Ball valve of Leader/ Sant/ Syall make. 2.5 inches Dia

EA 7966

355 P/F BALL VALVES 2.0" DIA:Supply and fixing ISI marked Ball valve of Leader/ Sant/ Syall make. 2.0 inches Dia

EA 7292

356 INSTALLATION OF STP:Installation of STP pumps on Tank Manhole including connection with suction pipe, electrical, earthing etc.complete

EA 4500


357 4 WAY MANIFOLD:S/fixing of 4-way MS manifold on Tank manhole for providing connection to different dispensers

EA 5800

358 SILICA GEL TRAP Providing and fixing flanged end silica get trap for vent as per standard HPCL design including filling of silica getcrystals, cutting and reconnecting vent pipes, etc, complete

EA 2468

359 PIPELINE TRENCH360 Providing pipeline trench as per drawing with following internal width and

500mm depth including excavation, 100mm thick PCC 1:4:8, 230mm thick brick masonary in 1:5 CM, 12mm thick plastering inside in 1:4 CM, filling trench with sweet river sand, 150mm thick RCC 1:2:4 cover with reinforcement 10mm tor @ 125mm c/c on top and bottom as main steel and 8mm tor ring curing etc. complete, 35x35x6 angle will be paid separately.

361 300mm internal width RMT 1759362 450mm internal width RMT 3415363 Transportation of dispensing pumps form storage point to the retail outlet site

including loading, unloading etc., Complete.364 Up to 50KM distance . Rate per DU NO 1720365 Additional charges for KM beyond 50. Only oneway KM will be considered. KM 25366 Tanker unloading Hoses : Supply of eletrically bonded petroleum product

unloading hose with uniform bore of61mm dia and 3.3 mtr in length having neoperne rubber of premium quality in outer cover and acrylic nitrile rubber ininner lining with high degree of flexibility, reinforced with fully embeded helical wire and static copper wire foreletrical continuity, rubbrer hose should have outside corrugated without external armouring suitable for handlingpetroleum products up to working pressure of 3.5 kg/sqmm and confirming to IS 10733/1983 type 1B with plain endsand 2 nos heavy gun metal hose nipples with nitrile rubber rings fitted inside and assembled by 2 GI hose clips toeach side of above mentioned hose, supplier to provoide test certificate of eletrical continuity for each and 6 monthsGaurantee againest any manufacturing defects

EA 4637

367 GASKET ON TANK MANHOLE :The manhole cover to be fitted with providing and fixing 3mm thick RAF Gasket packing (Champion make,Champion-59) of 750mm dia.

EA 850

368 PART F DISMANTLING WORKS369 Dismantling of existing pump island 1m wide and carting away debris etc.

complete.RMT 343

370 Exhuming under ground tanks with all fittings from earth pit including disconnecting suction, fill, vert pipe , opening man hole cover, excavation, dewatering if encountered, degassing of tank, stacking the tank as directed by EIC etc. Complete. Back filling with sand will be paid separately.

371 9KL tank NO 5809372 16/14 KL tank NO 9001373 22 KL tank NO 11032374 Dismantling of existing building/structures375 Dismantling of RCC roof, beam, column including carting away debris CUM 574376 Removal of AC sheet from roof or canopy roofing sheet and stacking as directed

by EIC.SQM 60

377 Removal of Canopy false ceiling including scafolding and stacking as directed by EIC.

SQM 73

378 Removal of structural steel and stacking as directed by EIC MT 3102379 Dismantling of brick masonary/PCC /RR masonary including carting away debris CUM 287

380 Removal of MS/ Aluminium doors/ windows/fixed glazing and stacking as directed by EIC.

SQM 45


381 Dismantling of RCC driveway 150mm thick using concrete cutter for cutting smooth including carting away debris. Rate to include cutting both side of a trench width 400/600 and removal of debris. Length of the trench shall be considered for payment purpose.

RMT 1633

382 Dismantling of existing pipeline.383 40mm dia RMT 26384 50mm dia RMT 37385 80mm dia RMT 42386 Dismantling of existing pump including removal of pump and disconnecting

pipeline etc. complete.NO 390

387 Installing CITY PYLON/ REGULAR HP MASTERPOLE Board on the already constructed/existing RCC foundation/ New Foundation with the help of Crane and all the required tools and machinery in proper line and level etc complete.Foundation will be paid extra

EA 4530

388 PART G BORE WELL389 Drilling 6.5" borewell up to required depth in all kinds of soil including rock using

air compressor rig. Rate to include washing with compressor after installation of casing pipe, providing bentonite soil if required etc., complete.

RMT 390

390 Drilling 6.5" borewell Slow rig up to required depth in all kinds of soil including rock using air compressor rig. Rate to include washing with compressor after installation of casing pipe, providing bentonite soil if required etc., complete.

RMT 920

391 Supply and fixing 180mm dia MS casing pipe of minimum 2mm thick RMT 1074392 Supply and fixing 165 mm dia PVC slotted pipe 6 KG/SQCM pressure rating RMT 893

393 Supply and fixing 6" dia HDPE casing pipe 6 KG/SQCM pressure rating RMT 445394 Supply and fixing 6" dia HDPE slotted pipe 6 KG/SQCM pressure rating RMT 474395 Supply and fixing 5" dia HDPE casing pipe 6 KG/SQCM pressure rating RMT 345396 Supply and fixing 5" dia HDPE slotted pipe 6 KG/SQCM pressure rating RMT 362397 Supply and installation of 1.5 HP single phase submersible pump of Kirloskar

make cat no. KU4-0709S equivalent of approved make discharge range 1.2 - 8 cum/hr head range 59-10 M alongwith dry run preventor and starter

NO 25376

398 Supply and installation of 32 mm NB HDPE pipe with GI nipple at both ends. RMT 182

399 Supply and laying 3 C X 2.5 sqmm copper flat cable RMT 117400 Carrying out geological testing for finalisation of location of borewell NO 1972401 Supply and installation of single phase 1.5 HP jet pump with starter of approved

makeNO 13805

402 Supply and installation of 32 mm NB HDPE pipe and 25 mm NB HDPE pipe with required accessories for jet pump

RMT 201

403 Collection of water sample from the borewell and getting it tested from approved laboratory for the potability. Thereport to be submitted to the HPCL site-in-charge

EA 1930

404 PART H RAIN WATER HARVESTING AND GREEN SCAPE405 Providing rain water harvesting type I as per attached drg. NO 12129406 Supply of red earth for gardening CUM 600407 Supply of Sand CUM 1346408 Supply of manure CUM 467409 Laying of red earth and manure after mixing in 1:1 proportion for lawn. CUM 113410 Supply and planting Korean grass for lawn. SQM 294411 Supply and plantation of plants like, Fig, casurina,bottle palm etc.,. Rate to

include excavation of pit of size 600 MM X 600 MM X 600 mm depth, filling the pit with red earth and manure etc.,

NO 172

412 PART I DG SET/ COMPRESSOR413 Installation of 10 -25 KVA DG set on AVM pads including shifting from storage

yard to DG room all cable connections, installation of fuel tank , battery connection, etc., complete. Silencer pipe shall be paid seperately.

NO 2757


414 Installation of DG panel including all cable connections NO 781415 Liaisoning fee for arranging enhancement of existing power supply in existing

outlet or for arranging new power connection for new outlets.LS 22000

416 Installation of HPCL supplied compressor including fixing of AVM pad NO 1772417 Installation of tyre inflator gauge wall mounted model ELGI with 5 M long hose

including providing 50 X 50X 6 angle postNO 312

418 Supply and installation of 15 mm NB GI pipe conforming to IS 1239 medium class.

RMT 97

419 Supply and fixing 15 mmdia MS ball valve NO 460420 PART J CANOPY421 STRUCTURAL STEEL WORK 422 Supplying, erecting and fixing in position Pre-fabricated structures at all

elevations for Canopy using structural steel sections ISMB/ISMC/ISA conforming to IS:2062, including cutting, welding or bolting, supply of bolts/nuts/washers etc., complete as per drawings including surface preparation and aplying one coat of Zinc Phosphate Primer before erection, and two coats of synthetic enamel paint as per specification after erection and all materials and labour complete (No welding is permitted at site). The rate quoted shall include cost of bolts, nuts, washers, welding and electrodes and any other consumables required for completing the work. Nutbolts shall not be considered for payment. Theoretical weight of steel sections shall be considered for payment.

423 Foundation bolt KG 127424 Beams, columns, trusses, plates MT 64505425 ROOFING426 Providing and installing roofing with Tracdek Hi Rib 100 or approved equivalent

bare Galvalume high tensile cold rolled steel as per AS 1397 Coating class AZ 150 (minimum 150 gm/Sq.M. Zinc-Aluminium alloy coating mass total of both sides), Yield strength 275 Mpa Thickness of bare metal : 0.42mm, Total coated thickness : 0.47mm. Approximate mass of completed roofing shall be 4.12 Kg/Sq.M. Rate shall be including providing ridge piece.

SQM 688

427 Supplying and fixing 20 SWG GI sheet facia with two coats Zinc chromate primer & two coats enamel paint including providing 30x6mm flat brackets at every 1m spacing.Required facia frame shall be paid separately.

SQM 1295

428 Providing and fixing 20 SWG thick Aluminium sheet Gutters of required shape in slope with 40 mm x 3 mm MS. Brackets at 1000 mm maximum spacing and 8 mm dia G I. J or L hooks, boltsand nuts, GI. Limpet and bitumen washers, sealing the joints with silicon sealant testing the gutter for leakage by filling water etc. Complete.

SQM 1381

429 FALSE CEILING430 Providing & fixing false ceiling system of Trac 150 F exterior grade or approved

equivalent of 0.5mm thick galvanised steel with stove enameled coil coated finish inter locking ceiling panels, carriers, suspension system and edge closure as per the following specification. Supplying and installation of exterior grade 150 F ceiling system comprising of 150 mm x 17 mm deep panels roll formed out of 0.5 mm galvanised steel with stove enameled coil coated finish. The panels shall be pre-treated and coil coated on one side in manufacturers standard colour shades as approved by the Architect/ Engineer in charge. The rear side of the panel shall be given a coat of primer and a wash coat while the finished side shall be given a coat of primer and finish colour coat in polyster paint for a min. dry film thickness of 20 microns, fixed on to the roll formed carriers 34.5 mm x 488 mm deep out of 6 mm thick Galvanised steed with prongs to hold panels in the module of 150 mm at maximum 1.2 mts. C/C. The carriers to be suspended from roof truss by rigid suspension angles as per manufacturer's recommendation. Panels shall be supplied in custom length upto maximum of 5 mts. Job also includes providing ceiling flashing using factory formed 0.5 mm thick Polyster coated galvanised steel material. Rate

SQM 1049

431 CANOPY LIGHTING ELECTRICAL WORKS


432 Supply and laying of 3Cx2.5 sq mm size 1100V grade PVC insulated armoured copper cable in the existing cable duct/clamping on wall/column/structural steel etc. for canopy light/banding light wiring including end termination.

RMT 192

433 Supply of 250W metal hallide canopy light fixtures with lamp cat no. WHH 98250S WIPRO make or approved equivalent with metal hallide lamp 250W of osram/philips equivalent.

NO 6180

434 Installation, testing and commissioning of 250W metal hallide light fixtures. Rate shall be inclusive of all accessories, inter connection of wires etc. Complete.

NO 494

435 Providing and fixing CFL Luminare with 36W lamp-3nos WIPRO make 4336SGW or equivalent make of philips/crompton /Bajaj.

NO 6372

436 PVC PIPE437 Providing and fixing 6" dia PVC pipes of 6 Kg/sqcm of Prince Make or

equivalent make as per IS 4985 for rain water pipes including all fittings like bands , shoes etc., MS fabricated bracket as per requiment etc. All complete as directed by the EIC.

RMT 572

438 Providing and fixing 4" dia PVC pipes of 6 Kg/sqcm of Prince Make or equivalent make as per IS 4985 for rain water pipes including all fittings like bands , shoes etc., MS fabricated bracket as per requiment etc. All complete as directed by the EIC.

RMT 369

439 PART K ITEMS RELATED TO STRATEGY FORMAT OUTLETS440 PCC 1:2:4 PRE CAST KERB WALL Providing and laying Precast concrete

blocks of approved size and shape for kerb wall with PCC 1:2:4 mix using 20mm to 12 mm stone aggregate including mixing, providing necessary shuttering, compaction and curing.

CUM 5186

441 POLISHED VITRIFIED CERAMIC TILE FLOORING Providing and laying 1st quality polished vitrified Ceramic tiles Olympus/Sintra/Salt pepper grey/Snow carara/Rivera of Marbonite brand or approved equivalent of following size in flooring and free from cracks, warpage,fissures and flakes with straight edges and perfect corner laid at right angle as per design and pattern over a bedding of cement mortan of 30 mm thick CM 1:5 finishing the joints neatly with white cement mixed with matching colour pigment and finish in all respect and al l material and labour complete.

442 600MMX600MM SQM 2178443 900MMX900MM SQM 2356444 320mmx480mm dado SQM 1728445 Vitrified border tile RMT 1260446 RECTIFIED CERAMIC TILE DADO Providing and laying 1st quality rectified

Ceramic tiles of 8 mm thick of following size in dado of approved make and shade and free from cracks, warpage,fissures and flakes with straight edges and perfect corner laid at right angle as per design and pattern over a back coat plaster of 12 mm thick CM 1:4 and with neat cement paste , finishing the joints neatly with white cement mixed with matching colour pigment and finish in all respect and al l material and labour complete.

447 600mmx600mm SQM 1358448 300mmx600mm SQM 1180449 19MM THICK GRANITE FOR STAIRCASE STEPS Providing and fixing

machine cut and polished SPOTTED GRAY Granite slab of thickness of 19 mm selected & sorted for uniformity in colour, free from cracks, fissures and flakes with straight edges and perfect cornors . Rate to include making edge polish(nosing) , finishing the joints neatly with white cement mixed with coloring pigment to match color, polished and finished in all respect, all materials and labour complete.

SQM 3091


450 EUROPEAN TYPE WC Supplying and fixing coloured (pastel colour) vitreous china European type water closet comprising of the the following accessories including cutting and making good the walls & floors wherever required compleste as directed by Engineer In Charge A) Coloured ( pastel colour) viterous china pedestal type(Wall Mounted Cascade Model) European water closet of Model Cascade 0219-Parryware or 20028 Hindware make as per the direction of Engineer In Charge. B) 15mm NB brass angle valve as per ISI of approved brand as per the direction of Engineer In Charge C) 15 mm NB CP inlet connection with Brass unions at the ends. D) Commander make or equivalent matching colour polypropylene seat cover with necessary brass hinges and rubber bushes etc E) Nil F) Nil

NOS 10464

451 URINALS Supplying and fixing coloured (pastel colours) viterous china flat back large Auto Flush type (with sensor 51077 Jaquar) model. 0575 New Magnum- Parryware or Hindware 60006-Olympus half stall with CP flush valve, cp pipe connection, CP waste coupling , CP Brass bottle trap, 32 mm PVC waste line of required length, CP spreader unit and extension pipe etc. all complete as per the direction of Engineer In Charge

NOS 18927

452 Same as above- with out sensor NOS 8906453 HAND WASH BASIN Providing and fixing coloured Counter Top Oval type wash

basin of make 5500418 of Parryware 10016 oval of Hindware including the following accessories: - Providing and fixing Sensor Faucer 51071 Sensor pillar cock of Jaguar make - All other fillings like waste coupling, bottle trap, stop cock etc. from Clarion Range of Jaguar.

NO 19844

454 HAND WASH BASIN Providing and fixing coloured wash basins wall hung type with pedastal of make Basin CTM048 and pedastal 0375 of Parryware of Basin 10008 Viking and pedastal 11002 of Hindware including the following accessories. -Providing and fixing CP Parko make Pillar cock of No 1536- swan neck. -All other fittings like waste coupling, botle trap, stop cock etc. from classic line collection Parko

NO 5391

455 HEALTH FAUCET Providing and fixing Health Faucet of JAGUAR Cat No. 573. Complete as directed.

NO 1893

456 LIGHT FIXTURES Supply, fixing and commissioning of following light fittings. Rate to include all accessories, interconnection of wires from ceiling rose to fittings etc.,

457 Canopy light fitting- MPF-921/150W with CDMTD lamp of Philips make or equivalent .

NOS 6866

458 Yard light fitting- SGP 325 GLA 250W with lamp Philips make or equivalent . .

NOS 9785

459 Tube light fitting for office spaces- TCS 306 /236 HPF with lamp Philips make or equivalent .

NOS 2844

460 CFL Luminaries for general areas, passages, toilets - FCS 518 with lamp Philips make or equivalent .

NOS 1273

461 Tube light fitting for stores, staff room, recreation, dormitory etc.- TMC 21 /136 LPF with lamp Philips make or equivalent .

NOS 1085

462 Tube light fitting for ARB area (Customer)- FBS 300 P5 recess mounted with lamp Philips make or equivalent .

NOS 5628

463 Supply, fabrication, erection of yard light pole fabricated from 3mm thick Galvanised sheet octagonal shape tapered , bottom diagonal 100mm, 6.0m height including providing pedestal of size 0.45mx0.45mx1.2m depth in PCC 1:2:4, excavation, 16mm dia foundation bolt, 450mmx450mmx8mm thick base plate ,painting the pole with two coats of sinthetic enamel paint over a coat of zinc phosphate primer, finishing the above ground portion of pedestal with 12mm thick plaster etc. complete.

NOS 10096

464 Providing and fixing Mineral Fibre grid false ceiling with required accessories SQM 702

465 Providing and fixing false ceiling with Armstrong panel with required accessories

SQM 928


466 Providing and fixing Locker Cabinet for staff room with block board 20mm sides and back and shutters of 20mm thick grey prelaminated block board .Depth of cabinet 450mm.

SQM 1965

467 Providing and fixing Storage Cabinet with block board 20mm sides and back and shutters of 20mm thick grey prelaminated block board .Depth of cabinet 450mm.

SQM 2064

468 Providing and fixing stainless steel pipe hand railing for stair case for public with polished stainless steel pipe at two levels with 40mm and 32mm dia pipe of 3.25mm wall thickness and with SS plate balusters 95x6mm thick ..Length of staicase shall be considered for payment.

RMT 7447

469 Providing and fixing Mild steel pipe hand railing for stair case for staff with 32mm dia MS pipes 1239 Medium for horizontal as well as verticals including painting with deep blue colour synthetic enamel paint 1st quality over two coats of zinc phosphate primer.Total length of the pipe (not the length of staircase) shall be considered for payment

RMT 531

470 Supplying and fixing approved make FLP Junction box 3 way including required connector, 10A SPMCB,capping all un used openings.

NO 2153

471 Providing earth pits with maintenance free Earth Electrodes duly approved by the concerned State Electrical Board/ Electrical Inspectorate as follows. Supply, installation, testing and commissioning of Safe Earth Electrode of ASHLOK make, type T - 50 includig the required special compound, and all civil works installed as per IS: 3043 and provision of 450 mm x 450 mm removable CI cover. Earth test megger report to be submitted after installation

NOS 12886

472 Supplying , fabrication , welding & Laying Heavy quality 'C' Class ERW black steel bevelled end pipeline Conforming to IS 1239 (part I) – latest edition to the required slope & alignment with heavy duty GI fittings like elbows, tees including doping pipe line with 3 coats of 'Shalimastic – HD THIXOTROPIC of STP cold applied anti corrosive treatment after preparing the surface as per manufacturer specifications. The joints are to be made leak proof by using jointing materials like Litharge, Glycerin, Shellac, holdite . The pipes laid above ground shall be painted with two coats of synthetic enamel over two coat of zinc phosphate primer of approved quality and shall be color coded as per instruction of EIC. The pipeline shall be tested at a pressure of 5 kg/sqcm.

473 50mm NB suction pipe RMT 756474 80mm NB for fill pipe RMT 1064475 Supply and installation of Emco Envirolite FRP lightweight manhole cover

conforming to EN 124 Class B125 / AASHTO HS20 Designed to adhere strictly within standards set by International SHE regulations. Following test results to be submitted from the manufacturer .Surface Resistivity Test results to ensure that the Covers and Frames are spark resistant and that the Anti-Static properties of the Cover are less than 1 Mega ohm, which will prevents the build up of static charge.Dynamic Load Test using BS EN 124:1994.Compressive Load Test according to BS EN 124:1994. EN 124 Class C250 Rated to 250kN or 25 Metric Ton (55,000 lb)

476 1066 mm round flushed manhole covers NO 86132477 760 mm squar flushed manhole covers NO 55286478 Supply and installation of KPS Sweeden make FRP lightweight manhole cover

900mm dia 40T capacity designed to adhere strictly within standards set by International SHE regulations. With dip cap arrangement.

NO 78243

479 Same as above but 500mm dia manhole cover but without dip rod arrangement NO 43436

480 Providing 500mm high (above finished driveway level) crash barrier at both end of the pump island with 2nos SS round pipe of 40mm dia post and 2 nos 40mm dia SS round pipe, one no 50mm square SS pipe in horizontal position as per drawing. Wall thickness of SS pipe shall be 2mm. For one pump island, two nos barrier will be considered.

NO 16359

481 Supply and fixing 200W speakers of Philips make NO 592


482 Installation of Air Tower including providing foundation with PCC 1:2:4 200mm high above driveway level

NO 1543

483 Supply and fixing abrasion resistant retroflective raised Pavement markers 4"x4" size yellow colour of 3M make.

NO 330

484 Supply of moulded flexible FRP plasti traffic cone 600mm height of yellow colour with rubberised base.

NO 670

485 PAVER BLOCK 40mm thick Providing and laying approved brand/make 40mmthick cement coloured paving blocks of M 25 grade over a bed of 50mm thickwell compacted river sand bed laid over well prepared sub base to the requiredline and level including all materials, labour, machinery, transportation etc.,paving blocks should have chamfered top edges of not less than 4mm and shallbe laid and interlocked with a minimum of 2mm gap which in turn packed withriver sand, compacting with plate vibrator etc. Complete. Edge restraint withRCC 1:2:4 will be paid separately.

SQM 585

486 SAME AS ABOVE- COLOURED PAVER BLOCKS SQM 654487 PIPELINE TRENCH Providing pipeline trench as per drawing with internal size

600mm wide x500mm depth including excavation, 100mm thick PCC 1:4:8,230mm thick brick masonary in 1:5 CM, 12mm thick plastering inside in 1:4 CM,filling trench with sweet river sand, 150mm thick RCC 1:2:4 cover withreinforcement 10mm tor @ 125mm c/c on top and bottom as main steel and8mm tor ring as distribution, 50x50x6 angle edging, curing etc. complete. MSedge angle shall be paid separately.

RMT 4528

488 Applying retroreflective painting in Kerb wall SQM 110489 Providing and fixing 100mmx75mm size Teak wood frame for door including

supply and fixing 6 nos holdfast, painting with two coats synthetic enamel over one coat of wood primer, putty etc. complete

RMT 1231

490 Providing and fixing 32mm thick both side relaminated flush door shutter of Kitply/National make including providing 4” brass hinges 3 nos per shutter , one no Godrej round knob mortice lock etc. complete

SQM 4398

491 Providing grooves 10mmx10mm in plaster RMT 41492 ALUMINIUM FIXED GLAZING WITH 10MM CLEAR FLOAT GLASS: Providing

and fixing Aluminium fixed glazing with 25 micron coloured anodised aluminium section 8462 of JINDAL 31mmx42mmx1.6mm and glazed with 10 mm thick clear float glass of Saint Gobain/Tata make .

SQM 3545

493 ALUMINIUM GLAZED DOOR WITH 12MM TOUGHENED GLASS:Providing and fixing Aluminium glazed door with 25 micron coloured anodised aluminium section INDAL make and size 101.5 x 44.45x 2.5 on top and bottom or approved equivalent and glazed with 12 mm thick toughened glass Saint Gobain/Tata make and with stainless steel pipe/round acrylic handle and with locking arrangement .

SQM 6016

494 ALUMINIUM PANEL DOOR WITH 10MM LAMINATED PARTICLE BOARD:Providing and fixing Aluminium panel door with 25 micron coloured anodised aluminium section 9219 of INDAL 50x45x2.5 mm or approved equivalent make and infilling panel of 10 mm thick both side prelaminated particle board of approved make .

SQM 3496

495 ALUMINIUM FIXED GLAZING WITH 8MM FLOAT GLASS: Providing and fixing Aluminium fixed glazing with 25 micron coloured anodised aluminium section 8462 of Jindal 31x42x1.6 mm or approved equivalent make and glazed with 10 mm thick clear float glass Saint Gobain/Tata make

SQM 3608

496 ALUMINIUM OPENABLE GLAZED WINDOW WITH 8MM FLOAT GLASS: Providing and fixing Aluminium glazed openable window with 25 micron coloured anodised aluminium section 8462 of Jindal 31x42x1.6 mm or approved equivalent make for outer frame and shutter frame and glazed with 8 mm thick clear float glass Saint Gobain/Tata make

SQM 3422


497 Construction of pump island to the shape as per attached drawing 700mmwide in centre portion with 230mm thick brick masonary below finisheddriveway level approx. 450mm depth and 115mm thick brick masonry 150mmabove finished driveway level in CM 1:5, 12mm thick plastering in Cm 1:4roughened to receive granite tiles including excavation, 75mm thick PCC 1:4:8below brick masonary, sand filling etc. Stainless steel pipe guard shall be paidseparately.

RMT 2807

498 Providing and laying 50mm dia class B GI pipe conforming to IS 1239 medium for electrical cable conduit inside canopy column including elbob etc. complete.

RMT 566

499 Supply , fabrication, welding and erection of Monkey ladder fabricated out of 40mm dia MS pipe C class conforming to IS 1239 heavy for both side and 40x40x4mm MS angle for steps including grouting the ladder to wall and to ground with PCC 1:2:4.

MT 57314

500 Providing Grab bar Type A as per drawing made out of 40mm dia Stainless Steel pipe and 8mm SS rod for handicap toilet.

NO 3606

501 Providing Grab bar Type B as per drawing made out of 40mm dia Stainless Steel pipe and 8mm SS rod for handicap toilet.

NO 2964

502 Supply and fixing 6MM THK ASAHI/Modi float glass mirror with teakwood beading rate to include two coats of lacquer polishing , complete etc.

SQM 1969

503 SEPTIC TANK Prpoviding & constructing septic tank of internal size2400x1200x1800mm depth with excavation ,PCC1:4:8 100mm thick bed ,345/230mm thick brick masonary wall in CM 1:5 ,RCC1:2:4 100mm thick slabwith 8mm tor steel @150c/c both way , 115mm thick baffle wall with RCC beamat bottom ,12mm thick smooth cement plaster with water proofing compoundinside and exposed outside portion, providing 600mmx600mm size medium dutyCI cover, providing 75mm dia PVC vent pipe etc. Complete.

NOS 24506

Providing and laying mosaictiles NITCO external RY365 and GY 365 red andgrey colour as per design and pattern over a bedding of 25mm thick CementMortar 1:5,machine polishibg, finishing the joints neatly with white cementmixed with matching colour pigment and finish in all respect and al l materialand labour complete.

SQM 836

505 Providing and laying mangalore tile (elevation tile) LAFARGE MAKE/APPROVED MAKE over a bedding of 25mm thick Cement Mortar 1:5, andfinishing with one coat of painting .

SQM 695

506 Providing and fixing 40mm thick RCC jally in building SQM 862507 Providing and fixing 20x20mm MS square bar in vertical position 300mm height

above compound wall and 300mm inside compound wall @ 1000mm c/c andtwo nos 40x40 MS pipe of 3.25mm wall thickness in horizontal position on topof the compound wall for Junction outlet including painting with two coats ofzinc phosphate primer and two coats of synthetic enamel paint. One 40x40 pipeshall be painted with red colour and another shall be painted with bluecolour.Length of the compound wall shall be considered for measurement.

RMT 602

508 PRECAST RCC MANHOLE COVER Providing and fixing heavy duty precastRCC manhole cover of following size inspection chambers including 150mmthick frame and 100mm thick cover.

509 600mmX600mm internal size NO 2908510 450mmX450mm internal size NO 2105511 Supplying , erecting and fixing in position Pre- fabricated structures at all

elevations for Pergola using MS plate and sections (ISMB, ISMC etc.)conforming to IS:2062 , including cutting, welding or bolting, supply ofbolts/nuts/washers etc., complete as per drawings including surface preparationand applying two coat of Zinc Phosphate Primer and two coats of ducu (MRF)paint as per specification after erection and all materials and labour complete. (No welding is permitted at site). The rate quoted shall include cost of bolts, nuts,washers, welding and electrodes and any other consumables required forcompleting the work.

MT 56955


512 Supply and fixing 3/4” width flexible copper braided wire for earthing of Tank truck while unloading

KG 609

513 Supply and fixing heavy duty crocodile clip for earthing of tank truck while unloading

NO 75

514 Supply and laying following size HDPE PLP pipe for conduiting of Jain Irrigation make or equivalent. RCC/PCC/Brick masonary breaking, providing PCC over it shallbe paid separately.

515 50mm OD 42mm ID RMT 77516 32mm OD 26mm ID RMT 50517 Supply and fixing emergency light in canopy Pierlites make cat no. BILW2/36/4E

Inverter for 36WNO 14270

518 Installation of HPCL supplied Tank of 45 KL capacity in earth pit/ under driveway including providing holding down arrangement, Hydrostatic testing to pressure of 3.5m water column, supplying & filling with water with necessary 50mm dia pipe & on successful completion emptying out the water from tank, cleaning & drying the inner surfaces with cloth/ cotton waste etc., external doping with two coats tank mastic paint of STP make and hot 30/40 bitumen (total doping thickness 3mm), fixing all fittings as required.

NO 37485

519 LAND DEVELOPMENT: Excavation in any type of soil except hard rock up to a depth of maximum 2.5m from NGL, transportation of excavated soil to low lying area within the site premises, spreading, filling in 250mm thick loose layers including levelling with doser, watering, Compacting each layer with light duty vibro roller 25Mt (effective impact) to obtain field density 92% of MDD, Dressing top layer to the required slope, Testing of murum sample for OMC&MDD and testing of field dry density by core cutter for checking compaction of each layer. Payment will be made only for excavated quantity based on level taken before and after excavation. No separate payment shall be made for filling.

CUM 287

520 Excavation for roadway in hard rock with controlled blasting by drilling holes, blasting, trimming of bottom and side slopes in accordance with requirements of lines, grades and cross sections, loading and disposal of excavated rock outside the site premises to an un-objectionable place in all lifts (2.5m). Payment will be made only for excavated quantity based on level taken before and after excavation. The rock shall not be used for filling.

CUM 755

521 ALUMINIUM DOOR/FIXED GLAZING WITH 8MM GLASS Providing and fixing 20 micron coloured powder coated aluminium fixed glazing/aluminium door with 8 mm glass extruded built up section of wall thickness not less than 1.5 mm and approve make with glass panel fixed with Aluminium snap beading/ Neoprene / PVC gasket/CP Brass /stainless steel screws and fixed to the wall with requisite rawl plugs and screw or with fixing clips or with expansion hold fastners including necessary filling up of gaps at junctions, at top , bottom and sides with requisite PVC / neoprene felt / polysulphide sealant/sillicon sealant all complete as per architectural drawing and the direction of Engineer In-charge. Aluminium section of INDAL make or equivalent make with the following sections :

SQM 4228


Documents

Belgaum Rate Schedule - HPCLtenders.hpcl.co.in/tenders/tender_prog/TenderFiles/3511...SCHEDULE OF RATE FOR MODERNISATION OF RETAIL OUTLETS / CONSTRUCTION OF NEW RETAIL OUTLETS UNDER