Rafael Flores Luminant Power Luminant - NRC: Home Page · 2014. 9. 24. · Rafael Flores Luminant Power Executive Vice President P 0 Box 1002 & Chief Nuclear Officer 6322 North FM

Rafael Flores Luminant PowerExecutive Vice President P 0 Box 1002& Chief Nuclear Officer 6322 North FM [email protected] Glen Rose, Texas 76043Luminant

T 254.897.5550C 817.559.0403F 254.897.6652

Delivered Via FedEx

TXX# 14110

September 2, 2014

Texas Commission on Environmental QualityWater Quality DivisionApplications Review and Processing Team (MC148)12100 Park 35 CircleAustin, Texas 78753

Re: Luminant Generation Company LLCComanche Peak Nuclear Power PlantTPDES Industrial Wastewater Permit Renewal ApplicationPermit No. WQ0001854000

Dear Sir/Madam:

In accordance with the rules and regulations of the Texas Commission on Environmental Quality(TCEQ), Luminant Generation Company LLC hereby submits one original and three complete copies ofthe Industrial Wastewater Permit Application for renewal of the above referenced TPDES Permit. Acheck for the required renewal fee of $2,015.00 was mailed on September 2, 2014 to the TCEQ FinancialAdministration Division (Attachment A).

Luminant appreciates the opportunity to submit this permit renewal application. If there are anyquestions, please contact Ryan Bayle at 214-875-8294 or via e-mail at [email protected].

Sincerely,

Rafael Flores

By David P. Duncan,Director, Environmental Generation

RMBEnclosures

cc: US Nuclear Regulatory Commission, Document Control Desk, 11555 Rockville Pike, Rockville, MD20852 Q c .

LuminantLuminant Generation Company LLC

Comanche Peak Nuclear Power Plant

TPDES Industrial Wastewater Permit Application Renewal

Permit No. WQ0001854000

September 2014

TEXAS COMMISSION ON ENVIRONMENTAL QUALITYTCEQ INDUSTRIAL WASTEWATER PERMIT APPLICATION

INDUSTRIAL ADMINISTRATIVE REPORT

Submit this checklist with the application. Do not submit the instructions withthe application. Indicate if the following are included in the application.

Applicant Luminant Generation Company LLC

Permit Number WQOOO1854000

WORKSHEET Y N WORKSHEET Y N

Administrative Report 1.0 F7- Worksheet 7.0 [ TAdministrative Report 1.1 - FT Worksheet 8.0 V- FTSPIT [ - Worksheet 9.0 7 F TTechnical Report 1.0 F-V 7- Worksheet 10.0 7 IWorksheet 1.o T 7 Original USGS Map F-T 7--Worksheet 2.0 7- Affected Landowners Map 7 F-Worksheet 3.0 [ - Landowner Disk or Labels 7- 57Worksheet 3.1 7 F- Copy of Application Fee Check F [7vWorksheet 3.2 7- F-- All fees owed TCEQ are paid F-T 7-Worksheet 3.3 7 7 F Flow Diagram 1 7- -Worksheet 4.0 F7- - Site Drawing FT 7-Worksheet 4.1 --- T Original Photographs 7.- FWorksheet 5.0 FT 7- Solids Management Plan 7Worksheet 6.0 F [11 Water Balance FT 7

Please indicate by a check mark the amount submitted for the application fee:Major Amend. Minor(With or Renewal Amend.

EPA Classification New WithoutRenewal) Only /Mod.

Minor facility not subject tocategorical standards $350 __ $350 $315 __ $150promulgated by the EPA (40CFR Part 400-471)Minor facility subject tocategorical standards _ $1,250 _ $1250 ____$1215 __ $150promulgated by the EPA (40CFR Part 400-471)

Major facility N/A* __ $2,050 $2,015 -$450* All facilities are designated as minors until formally classified as a major by EPA.

For Commission Use Only:

Segment Number: County: Expiration Date:

Proposed/Current Permit Number: Region:

TCEQ-10411 (9/1/2010) Industrial Wastewater Permit Application - Administrative Report Page 1 of 18

INDUSTRIAL ADMINISTRATIVE REPORT 1. o

The following is requiredfor all applications--Renewal, New, And Amendment

Type of application:

F7 New TPDES [F7 New TLAP171 Major amendment with Renewal [F Major Amendment without RenewalUI Renewal of existing permit fl Stormwater only discharge

Minor amendment to permit l Minor modification to permit

If applying for an amendment to a permit, please describe the request in detail.

1. APPLICANT INFORMATION (Instructions, Page 18)

a. Facility Owner (Owner of the facility must apply for the permit.)What is the Legal Name of the entity (applicant) applying for this permit?Luminant Generation Company LLC

(The legal name must be spelled exactly as filed with the Texas Secretary of State,County, or in the legal document forming the entity.)If the applicant is currently a customer with TCEQ, what is the Customer Number(CN)? Search for your CN at:http://wwwl2.tceq.texas.gov/crpub/index.cfm?fuseaction=cust.CustSearch

CN 6032564

What is the name and title of the person signing the application?(The person must be an executive official meeting signatory requirements in TAC305.43(a).)Prefix (Mr. Ms, Miss): Ms.First/Last Name: Kim MerelesSuffix:Title: Vice President Environmental Services Credential:What is the applicant's mailing address as recognized by the US Postal Service?You may verify the address at: http://zip4.usps.comlzip4/welcome.jspOrganization Name: Luminant Generation Company LLC

Mailing Address: 1601 Bryan Street

Internal Routing (Mail Code, Etc.): EP 27-100BCity: Dallas State: TX ZIP Code: 75201Mailing Information if outside USA

Territory: Country Code: _Postal Code:Phone No.: (214) 875-8382 Extension:Fax No.: (214) 875-8699 E-mail Address: [email protected]


Indicate the type of Customer:FE] Individual Dj Sole Proprietorship-D.B.A.FD1 Limited Partnership [ CorporationM Trust ] Estate[• Federal Government [ State GovernmentEl County Government 0 City Government[D Other Government [l Other:Limited Liability Company

Independent entity

M" Yes[:] No (If governmental entity, subsidiary, or part of a larger corporation)

Number of Employees:0-20; n] 21-100; 1- 101-250; E 251-500; or 501 or higher

Customer Business Tax and Filing Numbers(Not applicable to individuals, governments, general partnerships or soleproprietors. REQUIRED for corporations and limited partnerships)

State Franchise Tax ID Number: 17529678207TX SOS Charter (filing) Number: 800881216Federal Tax ID: 75-2967820DUNS Number (if known): 102247793

b. Co-Permittee information (complete only if the operator must be a co-permittee)What is the Legal Name of the entity (operator) applying for this permit?

Operator N/A

(The legal name must be spelled exactly as filed with the Texas Secretary of State,County, or in the legal document forming the entity.)

If the operator is currently a customer with TCEQ, what is the Customer Number(CN)? Search for your CN at:http://www12.tceq.texas.gov/crpub/index.cfm?fuseaction=cust.CustSearch

CN

What is the name and title of the person signing the application?(The person must be an executive official meeting signatory requirements in TAC305.43(a).)Prefix (Mr. Ms, Miss):First/Last Name:Suffix:Title: Credential:What is the applicant's mailing address as recognized by the US Postal Service?You may verify the address at: http:!/zip4.usps.com/zip4/welcome.jsp


I

Organization Name:

Mailing Address:Internal Routing (Mail Code, Etc.):City: Dallas State: TX ZIP Code:Mailing Information if outside USA

Territory: Country Code: _Postal Code:Phone No.: Extension:Fax No.: E-mail Address:

Indicate the type of Customer:

[] Individual E] Sole Proprietorship-D.B.A.E1 Limited Partnership E] CorporationEl Trust E] EstateEl Federal Government rl State GovernmentEl County Government [] City Government[J Other Government Other:

Independent entity

El Yes[[ No (If governmental entity, subsidiary, or part of a larger corporation)

Number of Employees:

R 0-20; -]21-100; D[ 101-250; 251-500; or 501 or higherCustomer Business Tax and Filing Numbers(Not applicable to individuals, governments, general partnerships or soleproprietors. REQUIRED for corporations and limited partnerships)

State Franchise Tax ID Number:TX SOS Charter (filing) Number:Federal Tax ID:DUNS Number (if known):Provide a brief description of the need for a co-permittee:


c. Individual information (complete only if the facility owner or co-permittee isan individual)What is the Legal Name of the owner/co-permittee applying for this permit?N/AIf the owner/co-permittee is currently a customer with TCEQ, what is the CustomerNumber (CN)? Search for your CN at:http: //www12.tceq.texas.gov/crpub/index.cfm?fuseaction=cust.CustSearch

CN

What is the name and title of the person signing the application?(The person must be the individual. See signatory requirements in TAC 305.43(a).)Prefix (Mr. Ms, Miss):First/Last Name:Suffix:State Identification Number:Date of Birth:Assumed business or professional name:Business name:

What is the applicant's mailing address as recognized by the US Postal Service?You may verify the address at: http://zip4.usps.com/zip4/welcome.jsp

Mailing Address:Internal Routing (Mail Code, Etc.):City: State: TX ZIP Code:Mailing Information if outside USA

Territory: Country Code: _Postal Code:Phone No.: Extension:Fax No.: E-mail Address:

2. BILLING CONTACT (Instructions Page 21)

a. Billing Contact and Address InformationThe permittee is responsible for paying the annualfee. The annual fee will beassessed to permits active on September 1 of each year. TCEQ will send a billto the address provided in this section. The permittee is responsible forterminating the permit when it is no longer needed.Is the billing address the same as the permittee or co-permittee?

E Permittee rl Co-permittee M No, fill out this sectionPrefix (Mr. Ms, Miss): Mr.

First/Last Name: Gary SpicerSuffix:Title: Water Quality and Solid Waste Manager Credential:_

Organization Name: Luminant Generation Company LLC

Billing Mailing Address: 1601 Bryan Street


Internal Routing (Mail Code, Etc.): EP 27-095CCity: Dallas State: TX ZIP Code: 75201

Mailing Information if outside USA.Territory: Country Code: Postal Code:

Phone No.: (214) 875-8299 Extension:Fax No.: (214) 875-8699 E-mail Address:

3. APPLICATION CONTACT INFORMATION (Instructions, Page 21)If TCEQ needs additional information regarding this application, who should becontacted?

a. Application ContactPrefix (Mr. Ms, Miss): Mr.First/Last Name: Gary SpicerSuffix:Title: Water Quality and Solid Waste Manager Credential:Organization Name: Luminant Generation Company LLC


Internal Routing (Mail Code, Etc.): EP 27-095CCity: Dallas State: Texas ZIP Code: 75201


Phone No.: (214) 875-8299 Extension:Fax No.: (214) 875-8699 E-mail Address: [email protected] one or both: [W/ Administrative contact P/1 Technical Contact

b. Application ContactPrefix (Mr. Ms, Miss): Mr:First/Last Name: Ryan BayleSuffix:Title: Water Resources Coordinator Credential: P.G.Organization Name: Luminant Generation Company LLC


Internal Routing (Mail Code, Etc.): EP 27-090ECity: Dallas State: TX ZIP Code: 75201


Phone No.: (214) 875-8294 Extension:Fax No.: (214) 875-8699 E-mail Address: [email protected] one or both: : F,/ Administrative contact [0/ Technical Contact


4. DMR CONTACT INFORMATION (Instructions Page 21)Contact Responsible for Discharge Monitoring Reports (EPA 3320-1) Provide the nameof the person and their complete mailing address delegated to receive and submitDischarge Monitoring Report Forms.

Prefix (Mr. Ms, Miss): Mr.First/Last Name: Zeke MartinezSuffix:Title: Environmental Specialist Credential:Organization Name: Luminant Generation Company LLCMailing Address: 1601 Bryan StreetInternal Routing (Mail Code, Etc.): EP 27-115CCity: Dallas State: TX ZIP Code: 75201


Phone No.: (214) 875-8381 Extension:Fax No.: (214) 875-8699 E-mail Address: [email protected]

Did you know you can submit DMR data on line?Go to Sign up now at:https://www6.tceg.texas.gov/steerslEstablish an electronic reporting account when you get your permit number.

5. PERMIT CONTACT INFORMATION (Instructions, Page 22)Provide two names of individuals that can be contacted throughout the permit term.

Prefix (Mr. Ms, Miss): Mr.

First/Last Name: Gary SpicerSuffix:Title: Water Quality and Solid Waste Manager Credential:Organization Name: Luminant Generation Company LLCMailing Address: 1601 Bryan StreetInternal Routing (Mail Code, Etc.): EP 27-090CCity: Dallas State: TX ZIP Code: 75201



TCEQ-1 0411 (9/1/2010) Industrial Wastewater Permit Application - Administrative Report Page 7 of 18

Prefix (Mr. Ms, Miss): Mr.First/Last Name: Ryan Bayle

Suffix:Title: Water Resources Coordinator Credential: P.G.

Organization Name: Luminant Generation Company LLC


Internal Routing (Mail Code, Etc.): EP 27-090ECity: Dallas State: TX

Mailing Information if outside USA.Territory: Country Code:Phone No.: (214) 875-8294 Extension:Fax No.: (214) 875-8699 E-mail Address

Code: 75201B----

Postal Code:

;: [email protected]

6. NOTICE INFORMATION (Instructions, Page 22)

a. Individual publishing the noticesPrefix (Mr. Ms, Miss): Mr.

First/Last Name: Ryan BayleSuffix:Title: Water Resources Coordinator Credential: P.G.Organization Name: Luminant Generation Company LLC


Internal Routing (Mail Code, Etc.): EP 27-090ECity: Dallas State: TX ZIP Code: 75201



b. Method for receiving Notice of Receipt and Intent to Obtain a WaterQuality Permit PackageIndicate by a check mark the preferred method for receiving the first notice andinstructions:

[71 E-mail Address: [email protected]; [email protected]] Fax No.:E- Overnight/Priority mail: (self addressed, prepaid envelope required)W Regular Mail:

Mailing Address: 1601 Bryan StreetInternal Routing (Mail Code, Etc.): EP 27-090ECity: Dallas State: TX ZIP Code: 75201

c. Contact in the Notice


Prefix (Mr. Ms, Miss): Mr.First/Last Name: Gary Spicer

Suffix:Title: Water Quality and Solid Waste Manager Credential:Organization Name: Luminant Generation Company LLC

Phone No.: (214) 875-8299 Extension:

d. Public Place InformationIf the facility and/or outfall are located in more than one county, a public viewingplace for each county must be provided.

Public Building name: Somervell County Clerk's Office

Location within the building: County Clerk's OfficePhysical address of building: 107 N.E. VernonCity: Glen Rose, Texas 76043 County: Somervell

Contact Name: Candace (Candy) Garrett

Phone No.: (254) 897-4427 Extension:

e. Bilingual Notice Requirements:

For new permit, major amendment and renewal applications. Notapplicable for minor amendment or minor modification applications.Please call the bilingual/ESL coordinator at the nearest elementary and middleschools and obtain the following information to determine if an alternative languagenotice is required:

1. Is a bilingual education program required by the Texas Education Code at thenearest elementary or middle school to the facility or proposed facility?W1 Yes E- No (If No, alternative language notice publication is not

required; skip to item 7. SITE INFORMATION.)

2. Are the students who attend either the elementary school or the middle schoolenrolled in a bilingual education program at that school?M Yes M No

3. Do the students at these schools attend a bilingual education program atanother location?M Yes r] No

4. Would the school be required to provide a bilingual education program but theschool has waived out of this requirement under 19 TAC §89.1205(g)?7lYes F NNo

5. If the answer is yes to 1, 2, 3, or 4, public notice in an alternative language isrequired. Which language is required by the bilingual program?Spanish

This section of the application is only used to determine if alternativelanguage notice will be needed. Complete instructions on publishingthe alternative language notice will be in your public notice package.

TCEQ-10411 (9/112010) Industrial Wastewater Permit Application - Administrative Report Page 9 of 18

7. REGULATED ENTITY AND PERMITTED SITE INFORMATION (InstructionsPage 23)If the site of your business is part of a larger business site, a Regulated EntityNumber (RN) may already be assigned for the larger site. Use the RN assigned forthe larger site. Search TCEQ's Central Registry to see if the larger site may alreadybe registered as a regulated site at:http://www12.tceg.texas.gov/crpub/index.cfm?fuseaction=regent.RNSearch

If the site is found, provide the assigned Regulated Entity Reference Number andprovide the information for the site to be authorized through this application below.The site information for this authorization may vary from the larger site information.

TCEQ issued RE Reference Number (RN): RN 103044053

a. State/TPDES Permit No.: W00001854000 Expiration date: 03/01/2015

EPA Identification No. (TPDES Permits only): TX 00 658 54

b. Name of project or site (the name known by the community where located):Comanche Peak Nuclear Power Plant

c. Is the facility located in Bexar Comal Hays, Kinney, Medina, Travis, Uvalde, or

Williamson County? Li Yes Mi No

(If Yes, additional information concerning protection of the Edwards Aquifer may berequired.)

d. Is the location of the facility used in the existing permit correct? El Yes EINo

e. Does the site have a physical address?LI If Yes, complete Section A for a physical address.

l if No (the location description is not accurate or this is a new permitapplication, complete), complete Section B for site location information.

Section A: Enter the physical address for the site.

Verify the address with USPS. If the address is not recognized as a delivery address,provide the address as identified for overnight mail delivery, 911 emergencies, orother online map, tool to confirm an address.Physical Address of Project or Site:

Street Number: 6322 Street Name: North FM 56City: Glen Rose ZIP Code: 76043

Section B: Enter the site location information.If no physical address (Street Number & Street Name), provide a written locationaccess description to the site:

(Ex.: located 2 miles west from intersection of Hwy 290 & IH35 accessible on Hwy290 South)


f. City where the site is located or, if not in a city, what is the nearest city:

Glen Rose

g. ZIP Code where the site is located: 76043

h. County where the site is located somervell

i. Latitude: 32 deg. 17 min. 54 sec. Longitude: 97 deg. 47 min. 06 sec.

j. In your own words, briefly describe the primary business of the Regulated Entity:(Do not repeat the SIC and NAICS code)

Generation of electrictyk. Owner of treatment facility: Luminant Generation Company LLC

Ownership of Facility: F_ Public F' Private F Both - Federal

1. Owner of land where treatment facility is/will be: Luminant Generation Company LLC

(If not the same as the facility owner, there must be a long term lease agreement ineffect for at least six years. In some cases, a lease may not suffice - see instructions.)

m. Owner of effluent disposal site: N/A

(If not the same as the facility owner, there must be a long term lease agreement in

effect for at least six years.)

n. Owner of sewage sludge disposal site: N/A

(Required only if authorization is sought in the permit for sludge disposal on

property owned/controlled by the applicant.)

8. DISCHARGE/ DISPOSAL INFORMATION (Instructions, Page 26)

a. Is the point of discharge and discharge route in the existing permit correct?

E Yes F No If no, or a new or amendment permit application, please givean accurate description.

b. City or Town in which the outfall(s) is or will be located Glen Rose

c. County the outfall(s) is located: Somervell

d. Outfall Latitude: See attache page 11 a Longitude: See attached page 11 a

e. For all applications involving an average daily discharge of 5 million gallons per day

or more, provide the names of all counties located within loo statute miles

downstream of the point(s) of discharge. Somervell, Hood, Johnson, Bosque, McLennan, Falls & Hill


TCEQ INDUSTRIAL WASTEWATER PERMIT APPLICATIONINDUSTRIAL ADMINISTRATIVE REPORT

Applicant: Luminant Generation Company LLCPermit Number: WQ0001854000

DISCHARGE/ DISPOSAL INFORMATION

Outfall Latitude Longitude

001

002

003

004

320 17' 47.34"

320 17' 28.13"

320 17' 46.77"

320 17' 53.19"

970 46' 58.66"

970 47' 14.18"

970 47' 00.75"

970 47' 11.71"

Page Ila of 18

fL If a TLAP, is the location of the effluent disposal site in the existing permit accurate?

FE1 Yes M No If no, or a new or amendment permit application, please givean accurate description.

N/A

g. City or Town in which the disposal site is or will be located N/A

h. County the disposal site is located: N/A

i. Disposal Site Latitude: N/A Longitude: N/A

j. If a TLAP, describe the routing of effluent from the treatment facility to the effluent

disposal site:

N/A

k. For TLAP applications please identify the nearest watercourse to the disposal site to

which rainfall runoff might flow if not contained: N/A

1. Is the location of the sewage sludge disposal site in the existing permit accurate?

D- Yes M No If no, or a new permit application, please give an accuratedescription.

N/A

m. Provide an original full size USGS Topographic Map with all required information.Indicate by a check mark that the information is provided.

A] Applicant's property boundaryF-- Treatment facility boundaries[E] Labeled point of discharge and highlighted discharge routeE] Sewage sludge disposal site-- Effluent disposal site boundaries-- New and future construction

F-] 1 mile radius and 3 miles downstream informationI-1 All ponds

n. Is/will the treated wastewater discharge to a city, county, or state highway right-of-

way, or a flood control district drainage ditch? M-I Yes tEI No

If Yes, indicate by a check mark if:

F-- Authorization granted El Authorization pending(For new and amendments, provide copies of letters that show proof of contact andthe approval letter upon receipt.)


o. Is the facility located on or does the treated effluent cross American Indian Land?E- Yes F] No

9. MISCELLANEOUS INFORMATION (Instructions, Pages 29)

a. List each person formerly employed by the TCEQ who represented your companyand was paid for service regarding the application:N/A

b. Do you owe fees to the TCEQ?

If yes, please provide:Account number:

E- Yes F] No

Amount past due:

c. Do you owe any penalties to the TCEQ?

If yes, please provide:

Enforcement order number

R Yes FO No

Amount past due


10. SIGNATURE PAGE (Instructions, Page 30)

Permit Number: WQ0001 854000

Applicant: Luminant Generation Company LLC

Certification:

Kim Mireles VP Environmental Services

Typed or printed name Title

certify under penalty of law that this document and all attachments were preparedunder my direction or supervision in accordance with a system designed to assure thatqualified personnel properly gather and evaluate the information submitted. Based onmy inquiry of the person or persons who manage the system, or those persons directlyresponsible for gathering the information, the information submitted is, to the best ofmy knowledge and belief, true, accurate, and complete. I am aware there are significantpenalties for submitting false information, including the possibility of fine andimprisonment for knowing violations.

I further certify that I am authorized under 3o Texas Administrative Code §305.44to sign and submit this document, and can provide documentation in proof of suchauthorization upon request. .

Signature: _m____ _ __ Date: ______ ___

I (Use blue ink)

Subscribed and Sworn to before me by the said vVX Y\ y- n Le S

on this _ 2-_-_ day of q cjvLs- ,2o 1 j

My commission expires on the I • day of 0 c-4 ,20 t

Notary Public /

County, Texas Sandy C. Mixon

"Pubk Sta4te fUol..;,~ ... •Crv9E~.*¢s 1OI18t2Ot5

If co-permittees are necessary, each entity must submit an original, separate signature page.


TEXAS COMMISSION ON ENVIRONMENTAL QUALITYSUPPLEMENTAL PERMIT INFORMATION FORM (SPIF)FOR AGENCIES REVIEWING INDUSTRIAL

TPDES WASTEWATER PERMIT APPLICATIONS

TCEQ USE ONLY:Application type: Renewal Major Amendment Minor Amendment -New

County: Segment Number Admin Complete Date:

Agency Receiving SPIF:

Texas Historical Commission U.S. Fish and Wildlife

___ Texas Parks and Wildlife Department __ U.S. Army Corps of Engineers

This form applies to TPDES permit applications only. (Instructions, Page 34)

The SPIF must be completed as a separate document. The TCEQ will mail a copy of theSPIF to each agency as required by the TCEQ agreement with EPA. If any of the itemsare not completely addressed and/or further information is needed, you will becontacted to provide the information before the permit is issued. Each item must becompletely addressed.

Do not refer to a response of any item in the permit application form. Eachattachment must be provided with this form separately from the administrative reportof the application. The application will not be declared administratively completewithout this form being completed in its entirety including all attachments.

The following applies to all applications:

1. Permittee: Luminant Generation Company LLC

2. Permit No. WQoo 01854000 (EPA ID No.) TX 0065854

3. Address of the project (location description that includes street/highway,city/vicinity, & county)

6322 North FM 56, Glen Rose, TX 76043

4. Provide the name, address, phone and fax number of an individual that can becontacted to answer specific questions about the property.Name: Gary Spicer Company: Luminant Generation Company LLC

Phone number: (214) 875-8299 Fax number: (214) 875-8699

Street No.: 1601 Street name: Bryan Street; EP 090C Street type:P.O. Box: City: Dallas State: TX ZIP code: 752 01

Email: [email protected]


5. List the county in which the facility is located:Somervell

6. If the property is publicly owned and the owner is different than thepermittee/applicant, please list the owner of the property.

N/A

7. Provide a description of the effluent discharge route. The discharge route mustfollow the flow of effluent from the point of discharge to the nearest majorwatercourse (from the point of discharge to a classified segment as defined in 30TAC Chapter 307). If known, please identify the Segment Number.Via Outfalls 001, 002, 003 and 004 to Squaw Creek Reservoir; thence to Squaw Creek; thence to PaluxyRiver/North Paluxy River in segment 1229 of the Brazos River.

8. Please provide a separate 7.5 minute USGS quadrangle map with the projectboundaries plotted and a general location map showing the project area. Pleasehighlight the discharge route from the point of discharge for a distance of one miledownstream. (This map is required in addition to the map in the administrativereport).

9. Provide original photographs of any structures 50 years or older on the property.

lo. Does your project involve any of the following? Check all that apply.[-R a. Proposed access roads, utility lines, construction easementsR b. Visual effects that could damage or detract from a historic property's integrityR c. Vibration effects during construction or as a result of project designR d. Additional phases of development that are planned for the futureR e. Sealing caves, fractures, sinkholes, other karst features[-- f. Disturbance of vegetation or wetlands

11. List proposed construction impact (surface acres to be impacted, depth ofexcavation, sealing of caves, or other karst features).

None. This is an established facility that has been in commercial operation since 1!

12. Describe existing disturbances, vegetation and land use.

I Power plant with associated structures, facilities and roads.

THE FOLLOWING ITEMS APPLY ONLY TO APPLICATIONS FOR NEWTPDES PERMITS AND MAJOR AMENDMENTS TO TPDES PERMITS

13. List construction dates of all buildings and structures on the property.

14. Provide a brief history of the property, and name of the architect/builder, if known.


SUPPLEMENTAL PERMIT INFORMATION FORM ATTACHMENT

USGS SITE MAPAND FACILITY MAP

Luminant Generation Company LLCComanche Peak Nuclear Power PlantTPDES Permit No. WQ0001854000

4

THIS PAGE IS ANOVE1RýSIZED DRAWING OR

FIGURE,THAT CAN BE VIEWED AT THE

RECORD TITLED:THE NATIONAL MAP US TOP

HILL, CITY, TX 2013

WITHIN THIS PACKAGE...

D-OI

A

THIS PAGE IS ANOVERSIZED DRAWING OR

FIGURE,THA T CAN BE VIEWED AT THE

RECORD TITLED:THE NATIONAL MAP US TOP

NEMO, TX 2013

WITHIN THIS PACKAGE...

D-02



RECORD TITLED:COMANCHE PEAK NUCLEAR POWER

PLANT FACILITY MAPWITHIN THIS PACKAGE...

D-03

TECHNICAL REPORT 1.oINDUSTRIAL

THE FOLLOWING IS REQUIRED FOR ALL APPLICATIONSRENEWAL, NEW, AND AMENDMENT

1. FACILITY/SITE INFORMATION (Instructions, page 35)

a. Describe the type of activity and general nature of your business.

Generation of Electricity

b. SIC Code(s) 4911

NAICS Code(s) 221112 ,_, 2

c. Describe the wastewater generating processes.

See Attachment C: General Description

d. Provide a list of raw materials, major intermediates, and products handled at your facility.

Raw Materials Intermediate Products Final Products

water steam electricity

enriched uranium

TCEQ-10055 (05/15/2012) Industrial Wastewater Permit Application Technical Report Page 1 of 66

e. Indicate by a check mark that an attached facility map with the following information wasprovided with the application:

W-] Production areas, maintenance areas, materials handling areas, and waste disposalareas.

Z-j The location of each unit of the wastewater treatment plant including the location of

wastewater collection sumps and impoundments.

Attachment #: B: USGS Site Map and Facility Map

f. Is this a new permit application for an existing facility? - YesIf yes, provide background discussion below.

91 No

g. Is the treatment facility/disposal site located above the 10o-year frequency flood level?

W1 Yes E- NoList source(s) used to determine 10o-year frequency flood plain:

FEMA Flood Insurance Rate Map, Somervell County Texas Unincorporated Areas. Map #48425C0050C, April 3, 1995

If no, provide the elevation of the 1o0-year frequency flood plain and describe whatprotective measures are in use or planned to be used to prevent flooding of the treatmentfacility/disposal area.

h. For new or amendment permit applications, will there be discharge of fill material intoa water in the state for construction of the proposed outfall structure? 0 Yes 0 No

If no, proceed to Item No. 2. If yes, has the applicant applied for a U.S. Corps ofEngineers 404 Dredge and Fill permit? El Yes El NoIf yes, provide the permit number:

If no, provide the approximate date you anticipate submitting your application to theCorns.- -- r-lU


2. TREATMENT SYSTEM (Instructions, page 36)

a. List any physical, chemical, an/or biological treatment process that y ou use f or thetreatm ent of wastewater at your facility. Include a description of each treatment processstarting with initial treatment and finishing with the discharge point.

TREATMENT PROCESS TREATMENT UNIT CAPACITY or DIMENSIONS OUTFALL1. Solid Separation Condensate Polisher 34' x 153" x 8' 004

Decant Basin2. Solid Separation Clarifier Decant Basin 96'4" x 21' x 11' 0043. Oil/water Separation API Separator 4'6" x 4' x 5'6" 0044. Neutralization Equalization Basin 210' x 46'x 9' 0045. Radiological Filtration Wastewater Hold Tank 01 15' x 20' x 15' 0046. Radiological Filtration Wastewater Hold Tank 01 15' x 20' x 15' 0047. Activated Sludge Sewage Treatment Plant 60' dia x 11' H 003

For additional information, see Attachment C: General Description.

b. [71 Indicate by a check mark that an attached flow schematic with a water balance wasprovided with the applications showing each treatment unit and all sources ofwastewater flow into the treatment plant and to each outfall/point of disposal.

Attachment *: D: Water Flow Diagram

3. IMPOUNDMENTS (Instructions, pages 36)

Do you use or plan to use any wastewater lagoons, ponds, or impoundments

W] Yes -- No

If yes, complete item 3(a) for existing impoundments and items 3(a)-3(f) for new orproposed impoundments. If no, proceed to Item No. 4.

a. Provide the following information in the table provided:

Designation: Indicate t he appropriate u se designation for each p ond [ Treatment (T),Disposal (D), Containment (C), or Evaporation (E)]

Discharge Point: If a discharge occurs from the impoundments, designate the outfallassociated with the impoundment.

Liner I nformation: If the impoundments are lined to comply with specificationsoutlined for 1) a c ompacted clay Iiner (C), 2) an in-situ clay Iiner (I), or 3 ) asynthetic/plastic/rubber liner (S), indicate the liner type with the appropriate letterdesignation (see instructions for further detail on liner sp ecifications). If not,provide a reference to the attachment that provides a description of the alternate liner andany additional technical information necessary for an evaluation.

Dimensions: Provide t he dimensions(s), freeboard, surface area, an d storage volumecapacity of the impoundments. F or impoundments with irregular shapes, submit surfacearea (instead of length an d width), the average depth, an d the maximum depth b elownatural ground level.


Impoundment Information Table

Pond # SB Pond # A Pond # B Pond # C Pond# 0Designation Surge Basin LVW PondA 'Ž.i 9,jd B iS/WIPriC onMCW oi-

(T) (D) (C) or (E) Flow Equalization C,D,E,T C,D,E,T C,D,E,T C,E,T

Discharge Point

Outfall Number 004 004 004 004 004

Liner Information

Liner Type (C) (I) or (S) S S S S S

Alt. Liner Attachment Reference

Dimensions

Length (feet) 76 ft 410 ft 410 ft 410 ft 410 ft

W idth (feet) 76 ft 114 ft 114 ft 366 ft 100 ft

Depth from Water Surface 3 ft 14 ft 14 ft 10 ft 10 ft

Depth from Nat. Ground Level 5 avg NA max 16 avg NA max _6 avg NA max 12 avg NA max 12 avg NA max

Freeboard (feet) 2 ft 2 ft 2 ft 2 ft 2 ft

Surface Area (acres) 0.133 acres 1.07 acres 1.07 acres 3.44 acres 0.09 acres

Storage Capacity (gallons) 130,000 gal 1,600,000 gal 1,600,000 gal 6.400,000 gal 1,500,000 gal

Pond # EB Pond # Pond # Pond # Pond #

Designation Equalizaiion Basin

(T) (D) (C) or (E) C

Discharge Point . , . ..

Outfall Number 004

Liner Information ,. ... " , . .. .

Liner Type (C) (I) or (S) S (over concrete)

Alt. Liner Attachment Reference

Dimensions

Length (feet) 210 ft ft ft ft ft

Width (feet) 46 ft ft ft ft ft

Depth from Water Surface 9 ft ft ft ft ft

Depth from Nat. Ground Level(avg/max) (feet) 11 / NA / / / /

Freeboard (feet) 2 ft ft ft ft ft

Surface Area (acres) 0.22 acres acres acres acres acres

Storage Capacity (gallons) 1,200,000 gal ___ gal __ gal _ gal __ gal


I

THE FO LLOWING I TEMS A RE R EQUIRED 0 NLY FO R N EW 0 R PR OPOSEDIMPOUNDMENTS.

b. Indicate by a check mark if any of the following data was provided with the application:

Li Synthetic/plastic/rubber liner data[- In-situ clay liner data

Attachment #:

c. Are there any leak detection systems or ground water monitoring wells in place orplanned? F- Yes -- No

-- If yes, indicate by a check mark that a separate attachment was provided with the leakdetection system information for each pond and/or gr ound water monitoring welldata.

Attachment #:

d. Is t he b ottom of the p ond a bove t he s easonal h igh water t able in t he shallowest waterbearing zone?

[F Yes F No

-- If no, indicate by a check m ark that additional information was provided describingthe depth of the seasonal high water table in the shallowest water bearing zone inrelation to the depth of the bottom of the new or proposed impoundment and how thismay or may not impact groundwater.

e. Indicate by a check mark that the following information was provided:

F-L A USGS quadrangle map or a color copy of original quality and scale which accuratelylocates and identifies water supply wells and/or monitor wells within 1/2 mile radius ofthe impoundments.

L- Copies of State Water Well Reports (driller's logs, completion data), and data on depthsto g round water fo r water supply w ells in cluding a description o f how t he d epths t oground water were obtained.

For TLAP permit applications:F-- Indicate by a check mark t hat t he new or proposed impoundment(s) and the landapplication disposal area are located in the same general area and the information for thisitem is provided in Worksheet 3.0 (item 8).

f. Li Indicate by a check mark id any data was provided with the application pertaining tothe ground water, soils, geology, etc. used to assess the potential for migration of wastesfrom the impoundments and/or the potential for contamination of ground water orsurface water.

4. OUTFALL/DISPOSAL METHOD INFORMATION (Instructions, pages 39)Complete the following tables to describe the location and wastewater discharge or disposaloperations f or each outfall for discharge operations and for each point of disposal f or TLAPoperations.

For TIAP permit applications: Indicate the disposal method and each individual irrigationarea (I), evaporation pond ( E), or subsurface drainage system (S) by providing theappropriate letter designation for the disposal method followed by a numerical designation foreach disposal area (e.g. evaporation pond, application area) in the space p rovided for "Outfall"designation (e.A. "Ei" for evaporation pond 1 , "12" for irrigation area No. 2, etc.).

TCEQ-"10055 (05/15/ 12) Industrial Wastewater Permit Application Technical Report Page 5 of 66

OUTFALL: 001

Latitude Longitude Location Description

32 17 47.34 97 46 58.66 From the once-through cooling water discharge canalPermitted Flow (MGD) Proposed Flow (MGD) to Squaw Creek Reservoir

Dly Avg Dly Max Dly Avg Dly Max Discharge Duration

3168 3168 3168 3168 24 (hrs./day) 30/31 (days/mo.) 12 (mo./year)

El Pumped F-1 Gravity Measurement Device: record i--lntermittent =----Seasonal =llContinuous

Contributing Wastestreams: Volume (MGD) % of Total Flow

Once-through cooling 3168 >99.95

Previously monitored effluent from Outfall 004 1.128

OUTFALL: 003


32 17 146.77 97 47 00.75 From the Sewer Treatment Plant to Squaw Creek

Permitted Flow (MGD) Proposed Flow (MGD) Reservoir


report report report report 24 (hrs./day) 30/31 (days/mo.) 12 (mo./year)

EiPumped F"I Gravity Measurement Device: Estimate Intermittent Seasonal I]Z.Continuous


Sanitary sewage effluent 0.078 100

OUTFALL: 004


32 17 53.19 97 47 11.71 From the Waste Management System to Outfall 001Permitted Flow (MGD) Proposed Flow (MGD) and/or Squaw Creek Reservoir


report report report report 24 (hrs./day) 15 (days/mo.) 12 (mo./year)

Ml Pumped r0 Gravity Measurement Device: estimate Ji•lntermittent Seasonal Continuous


Low volume waste (washdown water, floor/equipment drains

miscellaneous uses, water treatment wastes) 1.128 Variable

Storm water runoff from bermed areas Variable Variable

Previously monitored effluent from Outfall 104 Variable Variable

Alternative Discharge Location:

32 deg. 18 min. 06.31 sec N; 97 sec. 47 min. 16.59 sec. W


OUTFALL: 104


32 17 1 53.17 97 47 135.25 From the Metal Cleaning Waste Pond to Low VolumePermitted Flow (MGD) Proposed Flow (MGD) Waste Retention Ponds to Outfall 004


report report report report N/A (hrs./day) N/A (days/mo.) N/A (mo./year)

1 Pumped = Gravity Measurement Device: estimate LJ•intermittent r'Seasonal =-'lContinuous


Metal cleaning wastes Variable Variable

OUTFALL:


- I I I IPermitted Flow (MGD) Proposed Flow (MGD)


___(hrs./day) __ (days/mo.) -_(mo./year)

Pumped M Gravity Measurement Device: Intermittent Seasonal Continuous


TCEQ-1 0055 (05/15/2012) Industrial Wastewater Permit Application Technical Report Page 7a of 66

5. BLOWDOWN AND ONCE-THROUGH COOLING WATER DISCHARGES(Instructions, page 40)

a. Does y our f acility u se any cooling_ towers or boilers that discharge blowdown or otherwastestreams to the outfall(s)? I- Yes F- No

b. Does your facility discharge once-through cooling water to the outfall(s)? [-7 Yes 1- No

c. If yes to either item a or b, indicate with a check mark that the appropriate MSDS withthe following information for each chemical additive was submitted with the application.

Z Manufacturers Product Identification Number.Z Product use. (e.g., biocide, fungicide, corrosion inhibitor, etc.)Z Chemical Composition including Chemical Abstracts System (CAS) number for each

ingredient.Z Classify product as non-persistent, persistent, or bioaccumulative.Z Product or active ingredient half-life.Z Frequency of product use (e.g., 2 hr/day once every two weeks).ZI Product toxicity data specific to fish and aquatic invertebrate organisms.

Z Concentration of whole product in wastestream (if above item is for whole product)W] Concentration of active ingredient in wastestream (if above item is for active ingredient)

Please provide a summary of this information in addition to the submittal of the MSDS foreach specific w astestream an d the associated ch emical a dditives a nd specify which outfallsare affected.

Attachment: E: Boiler Chemical Additives and Attachment F: Once-through Cooling Chemical Additives

d. Cooling Towers and Boilers

Number of Units Daily Avg. Blowdown Daily Max Blowdown

Cooling Towers 0 cooling towers Daily Avg: 0 gallons/day Daily Max: 0 gallons/day

Boilersj1 boilers Daily Avg: gallons/day Daily Max: gallons/day

Note: The Auxiliary Boiler is an emergency back-up system that is only activated in the event of a loss of steam generator use or for periodic maintenance.

6. STORMWATER MANAGEMENT (Instructions, page 41)

Are there any existing or proposed outfalls which discharge stormwater runoff commingledwith other wastestreams?

Z Yes F- No. If yes, provide the following information. If no, proceed to Item No. 7.

a. Provide a brief narrative description of the in dustrial processes and activities that occuroutdoors or in some manner that may result in exposure of the materials to precipitationor runoff in areas where runoff is generated.Storm water runoff from the turbine generator area for Unit 1 and small construction projects in the drainage area are routed to theSafe Shutdown Impoundment and eventually to Outfall 002, The Unit 2 drainage area is routed through storm water outfalls permittedunder the TCEQ Multi-Sector General Permit (Permit No. TXR05K098). Storm water runoff from the diked chemical storage areas,transformers and (if feasible) small construction projects is suctioned into tanker trucks and discharged through Outfall 004.

Other areas in which storm water runoff may be exposed to industrial processes are permitted under the TCEQ Multi-Sector GeneralPermit (Permit No. TXR05KO98).


7. DOMESTIC SEWAGE, SEWAGE SLUDGE, AND/OR SEPTAGE MANAGEMENTAND DISPOSAL (Instructions, page 41)

a. Please check the appropriate m ethod(s) of domestic sewage a nd domestic sewage sludgetreatment/disposal and complete Attachment F if directed.

F] Domestic sewage is not generated on-site. PROCEED TO ITEM NO. 8.

FL1 Both do mestic and i ndustrial t reatment s ludge ARE commingled prior t o u se ordisposal. PROCEED TO ITEM NO. 8.

F-- Industrial wastewater and domestic sewage are treated separately and the respectivesludge IS NOT commingled prior to sludge use or disposal COMPLETEWORKSHEET 5.0 OF THIS APPLICATION.

[V] If your facility is a POTW, COMPLETE WORKSHEET 5.0 OF THISAPPLICATION.

-- Facility is connected to a wastewater treatment plant permitted to receive domesticsewage, or the domestic sewage is transported off-site to a permitted facility fortreatment and/or disposal. COMPLETE ITEM NO. 7.B.

[-- Domestic sewage is disposed of by an on-site septic tank. COMPLETE ITEM 7.B.

Ln Other: Please provide a detailed description below.

b. Provide t he n ame a nd TC EQ, NPDES, and/or TPDES P ermit N o. of t he waste disposalfacility which receives the domestic sewage/septage. If hauled by motorized vehicle,provide the name and TCEQ Registration No. of the hauler.

Plant/Hauler Name Permit/Registration No.

Disposal Facility: Republic Itasca Landfill 241 D

Hauler: SET Environmental / Cactus Environmental Services ILD981957236/TXD980796338

8. IMPROVEMENTS OR COMPLIANCE/ENFORCEMENT REQUIREMENTS (Instructions,page 42)

Is the permittee currently required to meet any implementation schedule for compliance orenforcement? E] Yes W1 No

If yes, provide a brief summary of the requirements and a status update.

TCEQ-1 0055 (05/15/2012) Industrial Wastewater Permit Application Technical Report Page 9 of 66

9. TOXICITY TESTING (Instructions, page 42)

Have any biological tests for acute or chronic toxicity been made on any of your discharges oron a receiving water in relation to your discharge within the last three (3) years?

W] Yes D- No

If yes, identify the tests and describe their purposes below. Please attach a copy of all testsperformed that have not been previously sent to the TCEQ and/or EPA.

Chronic an 24-hour Acute biomonitoring of Outfall 001 are completed as required by thecurrent permit. All test results have been previously submitted to the TCEQ.

lo. OFF-SITE/THIRD PARTY WASTES (Instructions, page 42)

Do you receive wastes from off-site sources for treatment in your facility, disposal on-site vialand application, and/or discharge via a permitted outfall E] Yes W]- No

If no, proceed to Item No. 11. If yes, proceed as directed.

a. Indicate with a check mark that a detailed attachment with the following information wasprovided with the application:

D-- List of wastes received D- Identified sources of wastes received-- Characterization of wastes received D- Name and addresses of generators

F-D Volumes of each waste received [D Description of the relationship ofF-D Info. on compatibility with on-site wastes waste source(s) with your facility's

activities.Attachment:

b. Is wastewater from a TCEQ, NPDES, and/or TPDES permitted facility commingled withyour wastewater after your final treatment and prior to discharge via your finaloutfall/point of disposal? F Yes F-1 No

If yes, provide the name, address, and TCEQ, NPDES, and/or TPDES permit number ofthe co ntributing facility an d a copy of any agreements an d/or contracts r elating t o t hisactivity.

c. Is your facility a Publicly Owned Treatment Works (POTW) that accepts processwastewater from any Significant Industrial User (SIU) and has or is required to have anapproved pretreatment program under the NPDES/TPDES program? E-- Yes -- No

If yes, complete Worksheet 6.o of this application.

ii. RADIOACTIVE MATERIALS (Instructions, page 43)

Are radioactive materials mined, used, stored, or processed at this facility? W] Yes [-] NoIf yes, Provide alist of the materials and the r esults of one analysis of your effluent inpicocuries per liter (pCi/L) for all radioactive parameters which may be present.

Radioactive Materials Conc. (pCi/L)All radioactive materials used at this facility fall under the jurisdiction of the

Nuclear Regulatory Commission (NRC)

i


THE FOLLOWING ITEMS ARE ONLY REQUIRED FOR EXISTING PERMITTEDFACILITIES.

12. MAJOR AMENDMENT REQUESTS (Instructions, pages 43)

Are you requesting a major amendment of an existing permit? E- Yes V1 NoIf yes, list each specific request and provide discussion on the scope of any requestedpermit changes.

If necessary, provide supplemental information or additional data that will support therequest.

13. MINOR MODIFICATION REQUESTS (Instructions, page 43)

Are you requesting any minor modifications to the permit? [Z] Yes E- No Note: see theinstructions for an exclusive list of changes considered as minor modifications.

If yes, list and discuss the requested changes.

Requesting a Minor Modification with renewal of the existing permit to remove Outfall 005in accordance with §305.62(c)(3)(E).

14. MINOR AMENDMENT REQUESTS (Instructions, page 44)

Are you requesting any minor amendments to the permit? _ Yes V No

If yes, list and discuss the requested changes.


WORKSHEETSTO THE INDUSTRIAL WASTEWATER PERMIT APPLICATION TECHNICAL REPORT

Please review the worksheet requirements in the instructions and indicate by checking eitheryes or no which worksheets are required, completed, and submitted with the technical report.Worksheets that are not applicable do not need to be submitted with the technical report.

COMPLETED ANDSUBMITTED WITH

WORKSHEET THE TECHNICALREPORT:

YES NO

1.0: EPA EFFLUENT CATEGORICAL GUIDELINES [F U2.0: POLLUTANT ANALYSES REQUIREMENTS [7-3.0: LAND DISPOSAL OF EFFLUENT 7-[-3.1: SURFACE LAND DISPOSAL OF EFFLUENT 1 [73.2: SUBSURFACE LAND DISPOSAL OF EFFLUENT 7--73.3: SUBSURFACE AREA DRIP DISPERSAL SYSTEM LAND 7[V

DISPOSAL OF EFFLUENT

4.o: RECEIVING WATERS [7T4.1: STREAM PHYSICAL CHARACTERISTICS WORKSHEET 7 175.0: SEWAGE SLUDGE MANAGEMENT AND DISPOSAL [7 76.0: INDUSTRIAL WASTE CONTRIBUTION 7 [77.0: STORMWATER RUNOFF 7-[78.0: AQUACULTURE [9.o: CLASS V INJECTION WELL 7 [7lo.o: QUARRIES IN THE JOHN GRAVES SCENIC RIVERWAY 7 [7


WORKSHEET 1.oEPA EFFLUENT CATEGORICAL GUIDELINES

REQUIRED FOR ALL APPLICATIONS FOR TPDES PERMITS FOR DISCHARGESOF WASTEWATERS SUBJECT TO EPA EFFLUENT LIMITATION GUIDELINES.

1. CATEGORICAL INDUSTRIES (Instructions, pages 47)

Is your facility subject to any of the 40 CFR effluent guidelines outlined in Table 1?Z Yes 0 No

If yes, provide the appropriate information in the table below. I f no, this worksheet isnot required.

Industry CFR

Steam Electric Power Generation 423

2. PRODUCTION/PROCESS DATA (Instructions, page 48)

a. Production data: Provide the appropriate data for effluent guidelines with productionbased effluent limitations.

b. Organic Chemicals, Plastics, a nd Synthetic Fibers Ma nufacturing D ata (40CFR Part 414): Provide each appropriate subpart and the percent of total production.Also provide the appropriate data for metal bearing wastestreams as required in 40 CFRPart 414, Appendices A and B.

%0/ of total Appendix A and BSubcategory production Metal Process

N/A


c. Refineries (40 CFR Part 419): Provide the applicable subcategory and a briefjustification for each.

N/A

3. PROCESS/NON-PROCESS WASTEWATER FLOWS: Provide a breakdown of processwastewater flow(s) and non-process wastewater flow(s) as directed. (Instructions, page 48)

PROCESS WASTEWATER NON-PROCESS WASTEWATER

Low volume waste Once-through cooling waterNon-chemical metal cleaning wasteChemical metal cleaning waste

4. NEW SOURCE DETERMINATION: Provide a list of wastewater generating processes subjectto effluent guidelines and the appropriate information. (Instructions, page 48)

Process EPA Guideline Date Process/Construction

Part Subpart Commenced

Low volume waste 423 N/A 1990

Non-chemical metal cleaning waste 423 N/A 1990

Chemical metal cleaning waste 423 N/A 1990

Once-through cooling water 423 N/A 1990


Luminant Generation Company LPComanche Peak Nuclear Power PlantTPDES Permit No. WQ0001854000

Worksheet 2.0 - Pollutant Analysis Requirements

Outfall 001 is an external, continuous discharge outfall of non-process wastewater. Completeanalytical results for Tables I and 2 are provided. Partial analytical results for Tables 5 and 7 arealso provided, because Base Neutral Compounds and Pesticides are not required for SteamElectric Stations. Grab samples representative of chlorination and/or bromination were used forthe analysis.

Outfall 002 is an external discharge of non-process wastewater. The Safe ShutdownImpoundment (SSI) is a safety component of the facility required by the Nuclear RegulatoryCommission (NRC) to provide a source of emergency cooling water for safe reactor shutdown inthe unlikely event of a failure of the Squaw Creek Reservoir dam. To date, this diversion ofcooling water has not been necessary. Since there has been no discharge from this outfall,complete pollutant analysis cannot be submitted as part of this application. Luminant GenerationCompany LLC understands that because we are not able to collect the samples for 002 tocomplete the analysis specified in the application, a post issuance testing requirement will beinserted as a provision of the renewed permit.

Outfall 003 is an external discharge of treated domestic wastewater; therefore, completeanalytical results are provided for Tables 1, 2, 3, 5, and 7.

Outfall 004 is an internal outfall although it has an option to be discharged directly to the lake.This option has never been used and has a flange installed to avoid use. Outfall 104 is aninternal outfall. Since both of these outfalls are internal, no samples were taken.

Pollutant analyses were performed by the following entities:

a. For Outfall 001, Temperature, pH and Total Residual Chlorine (TRC) analyses wereperformed by Company personnel in the on-site laboratory.

b. For Outfall 003, Temperature, pH, BOD5 and TSS were performed by Companypersonnel in the on-site laboratory.

c. All other analysis was performed by Pace Analytical Services, Inc., 400 W. BethanyRd. Suite 190, Allen, Texas 75013, (800-228-3764).

WORKSHEET 2.0POLLUTANT ANALYSES REQUIREMENTS

REQUIRED FOR APPLICATIONS SUBMITTED FOR A TPDES PERMIT. NOTREQUIRED FOR APPLICATIONS FOR A PERMIT TO DISPOSE OF ALLWASTEWATER BY LAND DISPOSAL OR FOR DISCHARGES SOLELY OF STORM-WATER RUNOFF. (General Requirements: Instructions, Pages 49-51)

1. TABLE i: Complete table required for all external outfalls.

Outfall No.: 0011 I IC 7EIG Effluent Concentration (ma/l)Pollutants Samp. Samp. Samp. Samp. AverageBOD (5-day)

WORKSHEET 2.0POLLUTANT ANALYSES REQUIREMENTS

REQUIRED FOR APPLICATIONS SUBMITITED FOR A TPDES PERMIT. NOTREQUIRED FOR APPLICATIONS FOR A PERMIT TO DISPOSE OF ALLWASTEWATER BY LAND DISPOSAL OR FOR DISCHARGES SOLELY OF STORM-WATER RUNOFF. (General Requirements: Instructions, Pages 49-51)

1. TABLE 1: Complete table required for all external outfalls.

Outfall No.: 0031 -- C IXIG Effluent Concentration (mqll)Pollutants Samp. Samp. Samp. Samp. AverageBOD (5-day)

2. TABLE 2:

Complete table required for all external outfalls which discharge process wastewater. Partialtable required for all external outfalls with nonprocess wastewater discharges. Stormwaterrunoff discharges commingled with other wastestreams shall complete the table as instructed(Instructions, Pages 49-51).

Outfall No.: 001 -IC MWG Effluent Concentration (pgll) (*1)Pollutants Samp. I Samp. 2 Samp 3. Samp. 4 Average MAL (pg/I)Benzene

2. TABLE 2:

Complete table required for all external outfalls which discharge process wastewater. Partialtable required for all external outfalls with nonprocess wastewater discharges. Stormwaterrunoff discharges commingled with other wastestreams shall complete the table as instructed(Instructions, Pages 49-51).

Outfall No.: 003 -]C XG Effluent Concentration (pg/I) (*1)Pollutants Samp. 1 Samp. 2 Samp 3. Samp. 4 Average MAL (pg/I)

Benzene

a. LABORATORY ACCREDITATION:Effective July 1,2 008, a 1ll aboratory tests p erformed must meet t he requirements o f30 TAC Chapter 25, Environmental Testing Laboratory Accreditation and Certificationwith the following general exemptions:

i. The laboratory is an in-house laboratory and is:1. periodically inspected by the TCEQ; or2. located in another state and is accredited or inspected by that state; or3. performing work for a nother company w ith a u nit I ocated in t he s ame

site; or4. performing pro bono work for a governmental agency or charitable

organization.

ii. The laboratory is accredited under federal law.

iii. The data are needed for emergency-response activities, and a laboratoryaccredited under the Texas Laboratory Accreditation Program is not available.

iv. The laboratory supplies data for which the TCEQ does not offer accreditation.

The applicant should r eview 3 o T AC Chapter 2 5 f or specific requirements. The followingcertification statement shall be signed and submitted with very application. SeeInstructions, Page 30, for a list of designated representatives who may sign the certification.

I, - certify th at a 11 laboratory te sts submitted with th isapplicatidn meet the requirements of 30 TAC Chapter 25, Environmental Testing LaboratoryAccreditation and Certification.

3. TABLE3:

Partial table (only those pollutants which are required by the conditions specified for eachoutfall where the pollutant is believed to be present) required for each external outfall wherethe source is identified. Not required for internal outfalls. (Instructions, Page 51)

a. TRIBUTYLTIN:

Is your facility or will your proposed facility be an industrial/commercial facility whichdirectly disposes of wastewater from the types of operations listed below or a domesticfacility which receive wastewater from the types of industrial/commercial operationslisted below? E] Yes 21 No

If yes, indicate with a check mark all of the following criteria which apply and providethe appropriate testing results in the table below.

FD1 Manufacturers and formulators of tributyltin or related compounds.- Painting of ships, boats and marine structures.

II Ship and boat building and repairing.- Ship and boat cleaning, salvage, wrecking and scaling.- Operation and maintenance of marine cargo handling facilities and marinas

E- Facilities engaged in wood preservingR Any other industrial/commercial facility for which tributyltin is known to be

present, or for which there is any reason to believe that tributyltin may be presentin the effluent.


b. ENTEROCOCCI

Does your facility or will your proposed facility discharge directly into saltwaterreceiving waters and:

Enterococci bacteria is expected to be present?

D Yes F7 No

Is domestic wastewater discharged?

0 Yes W1 NoIf yes to either question, provide the appropriate testing results in the table below.

c. E. coli

Does your facility or will your proposed facility discharge directly into fresh waterreceiving waters and:

E. coli bacteria is expected to be present?

F7 Yes 0 No

Is domestic wastewater discharged?

W•] Yes --1 NoIf yes to either question, provide the appropriate testing results in the table below.

TABLE 3

Outfall No.: 003 1oC .G Effluent Concentration

Pollutants Samp. 1 Samp. 2 Samp. 3 Samp. 4 Average MALTributyltin (•g/) N/A N/A N/A N/A N/A 0.010

Enterococci (CFU or MPN/iOo ml) N/A N/A N/A N/A N/A N/A

E. coli (CFUorMPN/ioo ml) 4.1

TABLE4

Outfall No.: IGC LIG Effluent Concentration (pgll) (*1) MALPollutants Samp. 1 Samp. 2 Samp. 3 Samp. 4 Avg. (pg/I)Beta-hexachlorocyclohexane 0.05

Carbaryl 5

Chlordane 0.15

Chlorpyrifos 0.05

2,4-D 10

Danitol ----

4,4'-DDD 0.1

4,4'-DDE 0.1

4,4'-DDT 0.1

Demeton 0.2

Diazinon 0.5

Dicofol 20

Dieldrin 0.1

Diuron 0.09

Endosulfan I (alpha) 0.1

Endosulfan II (beta) 0.1

Endosulfan Sulfate 0.1

Endrin 0.1

Gamma - Hexachlorocyclohexane (Lindane) 0.05

Guthion 0.10

Heptachlor 0.05

Heptachlor Epoxide 1.0

Hexachlorophene 10

Malathion 0.10

Methoxychlor 2.0

Mirex 0.2

Parathion 0.1

Toxaphene 5

2,4,5-TP (Silvex) 2

* Indicate units if different from mg/L.


5. TABLE5:

Complete table required for all external outfalls. Not required for internal outfalls.(Instructions, Page 52)

TABLE 5

Outfall No.: 001 oC qG Believed Believed Effluent Concentration (mg/I)Present Absent

Pollutants Average Maximum No. of Samples

Bromide X 15.5 1

Color(PCU) X 20 1

Nitrate-Nitrite(as N) X

I

5. TABLE5:

Complete table required for all external outfalls. Not required for internal outfalls.(Instructions, Page 52)

TABLE 5

Outfall No.: 003 oC @G Believed Believed Effluent Concentration (mg/I)Present Absent

Pollutants Average Maximum No. of Samples

Bromide X

6. TABLE 6:

Indicate w ith a check mark any of the industrial caategories applicable t o y our facility. Iftesting is required, indicate with a check mark in the box provided that the testing results forthe a ppropriate parameters in Table B-7 a re provided with the application. (Instructions,Page 52-53)

N/A

_ Adhesives and Sealants___ Aluminum Forming___ Auto and Other Laundries___ Battery Manufacturing___ Coal Mining___ Coil Coating___ Copper Forming___ Electric and Electronic Components___ Electroplating__ Explosives Manufacturing

_ Foundries

Gum and Wood ChemicalsSubparts A,B,C,ESubparts D,F

Inorganic Chemicals___ Iron and Steel Manufacturing___ Leather Tanning/Finishing

_ Mechanical Products Manufacturing___ Nonferrous Metals Mfg.___ Ore Mining(Subpart B)___ Organic Chemicals, Plastics, and Synthetic Fibers

Paint and Ink Formulation___ Pesticides

___ Petroleum Refining_ Pharmaceutical Preparations__ Photographic Equipment and Supplies_ Plastic and Synthetic Materials Manufacturing

___ Plastic Processing___ Porcelain Enameling

__ Printing and Publishing__ Pulp and Paperboard Mills

Subparts ASubparts B, C, D, RSubparts F, G, H, I, K, L, M, N, 0, PSubparts E, Q, S, TSubparts J, U

_ Rubber Processing_ Soap and Detergent Manufacturing

V Steam Electric Power Plants___ Textile Mills (Not Subpart C)___ Timber Products Processing

* Test if "believed present"

GC/MS Testing RequiredVolatileYes ElYes ElYes 0iYes ElNoYes LiYes E]Yes 0iYes ElNoYes 0i

Yes ElYes ELYes ElYes E]Yes ElYes ElYes ElNoYes 0iYes LiYes LiYes ElYes ELYes ELYes ELYes LiNoYes Li

*Li

Yes LiYes ElYes LiYes ELYes LiYes 0JYes [IYes EL

Acid

Yes ELYes ELYes LiNoNoYes LiYes [LYes LiYes LiYes []Yes Li

Yes ElYes LiYes []Yes ELYes LiYes ELYes L]Yes ElYes ELYes LiYes LiNo

Yes ELYes ELYes LiNoNoYes Li

Yes LiYes ELYes ELYes LiYes LiYes LiYes LiYes IZYes LiYes []

Base/Neutral

Yes LiYes LiYes LiYes ELNoYes DiYes LiYes ELYes ELYes ELYes Li

NoYes LiYes [IYes ELYes ElYes LiYes LiNoYes ELYes LiYes LiNoYes ELYes ELYes LiNoNoYes Li

*"L-

*L-iYes LiYes LiYes LiNoYes LiYes Li

Pesticides

NoNoYes ELNoNoNoNoYes 0iNo

NoNo

NoNoNoNoNoNoYes ElNoYes LiNoYes LiNoNoNoYes LiNoNoYes EL

Yes Li*Li

Yes EL*ELNoNoNoNoYes EL


7. TABLE 7:Please complete as directed and only for those parameters specified in Table 6Required for all external outfalls which contain process wastewater. Not required forinternal outfalls. Testing may be required for types of industry not specified in Table 6for specific parameters if believed present (Instructions, Page 53).

TABLE 7

Outfall No.: 001 LIC FORG Effluent Concentration (pgll)*Pollutants Number ofsAverage Maximum MAL (pgll)VOLATILE COMPOUNDS Samples

Acrolein

Effluent Concentration (pglI)*Pollutants Average Maximum Number of MAL (pgII)

Average Maximum Samples ML(gI

ACID COMPOUNDS

2-Chlorophenol

Effluent Concentration (pg/I)*

Pollutants Average Maximum No. of Samples MAL (pg/I)

BASE/NEUTRAL COMPOUNDS (cont.)1,2-Diphenyl Hydrazine (as Azobenzene) N/A 20

Fluoranthene N/A 10

Fluorene N/A 10

Hexachlorobenzene N/A 10Hexachlorobutadiene N/A 10

Hexachlorocyclopentadiene N/A 10

Hexachloroethane N/A 20

Indeno(1,2,3-cd)pyrene N/A 20

Isophorone N/A 10

Naphthalene N/A 10

Nitrobenzene N/A 10

N-Nitrosodimethylamine N/A 50

N-Nitrosodi-n-Propylamine N/A 20

N-Nitrosodiphenylamine N/A 20

Phenanthrene N/A 10

Pyrene N/A 10

1,2,4-Trichlorobenzene N/A 10

PESTICIDES

Aldrin N/A 0.05

alpha-BHC N/A 0.05

beta-BHC N/A 0.05

gamma-BHC N/A 0.05

delta-BHC N/A 0.05

Chlordane N/A 0.15

4,4-DDT N/A 0.1

4,4-DDE N/A 0.1

Dieldrin N/A 0.1

alpha-Endosulfan N/A 0.1

beta-Endosulfan N/A 0.1

Endosulfan Sulfate N/A 0.1

Endrin N/A 0.1

Endrin Aldehyde N/A 0.1

Heptachlor N/A 0.05

Heptachlor Epoxide N/A

PCB-1254 N/A 1.0

PCB-1221 N/A 1.0

PCB-1242 N/A

PCB-1232 N/A 1.0

PCB-1248 N/A 1.0

PCB-1260 N/A 1.0

PCB-1016 N/A 1.0

Toxaphene N/A 5.0* Indicate units if different from pg/I


7. TABLE 7:Please complete as directed and only for those parameters specified in Table 6

Required for all external outfalls which contain process wastewater. Not required forinternal outfalls. Testing may be required for types of industry not specified in Table 6

for specific parameters if believed present (Instructions, Page 53).

TABLE 7

Outfall No.: 003 -]C X-G Effluent Concentration (pgi)*PollutantsNubro

Average Maximum of MAL (pgll)

VOLATILE COMPOUNDS Samples

Acrolein

Pollutants

ACID COMPOUNDS

2-Chlorophenol

Effluent Concentration (pg/Il)*

Pollutants Average Maximum No. of Samples MAL (pg/I)

BASE/NEUTRAL COMPOUNDS (cont.)1,2-Diphenyl Hydrazine (as Azobenzene) N/A 20

Fluoranthene N/A 10

Fluorene N/A 10

Hexachlorobenzene N/A 10

Hexachlorobutadiene N/A 10

Hexachlorocyclopentadiene N/A 10

Hexachloroethane N/A 20

Indeno(1,2,3-cd)pyrene N/A 20

Isophorone N/A 10

Naphthalene N/A 10

Nitrobenzene N/A 10

N-Nitrosodimethylamine N/A 50

N-Nitrosodi-n-Propylamine N/A 20

N-Nitrosodiphenylamine N/A 20

Phenanthrene N/A 10

Pyrene N/A 10

1,2,4-Trichlorobenzene N/A 10

PESTICIDES

Aldrin N/A 0.05

alpha-BHC N/A 0.05

beta-BHC N/A 0.05

gamma-BHC N/A 0.05

delta-BHC N/A 0.05

Chlordane N/A 0.15

4,4-DDT N/A 0.1

4,4-DDE N/A 0.1

Dieldrin N/A 0.1

alpha-Endosu fan N/A 0.1

beta-Endosulfan N/A 0.1

Endosulfan Sulfate N/A 0.1

Endrin N/A 0.1

Endrin Aldehyde N/A 0.1

Heptachlor N/A 0.05

Heptachlor Epoxide N/A

PCB-1254 N/A 1.0

PCB-1221 N/A 1.0

PCB-1 242 N/A

PCB-1232 N/A 1.0

PCB-1248 N/A 1.0

PCB-1 260 N/A 1.0

PCB-1016 N/A 1.0

Toxaphene N/A 5.0* Indicate units if different from Pg/i


8. TABLE 8 (DIOXINS/FURAN COMPOUNDS):

Please complete as directed. Not required for internal outfalls. (Instructions, Pages 53-54)

a. Are any of the following compounds manufactured and/or u sed in a process at t hefacility? - Yes t-I NoIf yes, i ndicate w ith a ch eck mark the compound(s) which apply and provide a briefdescription of the conditions of its/their presence at the facility.

E- 2,4,5-trichlorophenoxy acetic acid (2,4,5-T) CAS #93-76-5F-1 2-(2,4,5-trichlorophenoxy) propanoic acid (Silvex, 2,4,5-TP) CAS #93-72-1F 2-(2,4,5-trichlorophenoxy) ethyl 2,2-dichloropropionate (Erbon) CAS #136-25-4[- o,o-dimethyl o-(2,4,5-trichlorophenyl) phosphorothioate (Ronnel) CAS #299-84-3[:] 2,4,5-trichlorophenol (TCP) CAS #95-95-4E- Hexachlorophene (HCP) CAS #70-30-4

b. Do you k now or have any reason to believe that 2,3,7,8 Te trachlorodibenzo-P-Dioxin(TCDD) or any congeners of TCDD may be present in your effluent? El Yes W1 NoIf yes, provide a brief description of the conditions for its presence.

c. If your responded yes to either item a or b, complete Table 8 as instructed.

TABLE 8

Outfall No. [-_ C [-- G Wastewater Sludge

Equivalent Concentration Equivalents Concentration Equivalents MAL (ppq)

Compound Factors (ppq) (ppq) (ppt) (ppt)

2,3,7,8-TCDD 1 10.0

1,2,3,7,8-PeCDD 0.5 50.0

2,3,7,8-HxCDDs 0.1 50.0

2,3,7,8-TCDF 0.1 10.0

1,2,3,7,8-PeCDF 0.05 50.0

2,3,4,7,8-PeCDF 0.5 50.0

2,3,7,8-HxCDFs 0.1 50.0

Total


9. TABLE 9 (HAZARDOUS SUBSTANCES):

Proceed complete as directed. Not required for internal outfalls. (Instructions, Pages 55)

a. Are there any pollutants listed in the instructions (page 55) believed present in the

discharge?

E-lYes ZNo

b. Are there pollutants listed in Item No. 1.d. on Page No. 1 of this technical report which

are believed present in the discharge and have not been analytically quantified elsewhere

in this application?

-]Yes -No

If your responded yes to either item, complete Table 9 as instructed.

TABLE 9

Average Maximum No. of Analytical(pgll) (pg/I) Samples Method


WORKSHEET 4.0RECEIVING WATERS

THE FOLLOWING IS REQUIRED FOR ALL TPDES PERMIT APPLICATIONS

1. DOMESTIC DRINKING WATER SUPPLY (Instructions, Page 70)

Is t here a surface water intake for domestic drinking water supply I ocated w ithin 5(five) miles downstream from the point/proposed point of discharge?

E- Yes -No

If yes, identify owner of the drinking water supply, the distance and direction to theintake, and locate and identify the intake on the USGS map. Indicate by a check markthat the requested information is provided: F

2. DISCHARGE INTO TIDALLY INFLUENCED WATERS (Instructions, Page 70)

a. Width of the receiving water at the outfall? N/A feet

b. Are there oyster reefs in the vicinity of the discharge? El Yes L-]No

If yes, indicate approximate distance and direction from outfall(s):N/A

c. Are there any sea grasses within the vicinity of the point of discharge?

R Yes -]No

If yes, provide the distance and direction to the grasses:N/A

3. CLASSIFIED SEGMENT (Instructions, Page 70)

Is the discharge directly into (or within 300 feet of) a classified segment?

El- Yes -- No

If yes, stop here. It is not necessary to complete items 4 and 5 and it is n otnecessary to complete Worksheet 2.1. If no, complete items 4 and 5.

4. DESCRIPTION OF IMMEDIATE RECEIVING WATERS (Instructions, Page 71)

Name of the immediate receiving waters: Squaw Creek Reservoir

a. Check the appropriate description of the receiving watersI- Man-made Channel or DitchF-- Stream or creekF-71 Lake or Pond

Surface area 3,300 acresAverage depth of the entire water body 46 feetAverage depth of water body within a 50o-foot radius or the discharge point 25 feet

F] Freshwater Swamp or MarshFD] Tidal Stream, Bayou, or Marsh[-I Open Bay[Z Other:

If a man-made channel, ditch or stream was checked above, provide the following:


b. Check one of the following that best characterizes the area upstream of the discharge.For new discharges, characterize the area downstream of the discharge (check one).

F-1 Intermittent (dry for at least one week during most years)Fl Intermittent with Perennial Pools (enduring pools containing sufficient habitat to

maintain significant aquatic life uses)F-1 Perennial (normally flowing)

Check t he method u sed t o c haracterize t he a rea u pstream ( or d ownstream f or n ew

dischargers):

F-- USGS flow recordsF-1 personal observationi-1 historical observation by adjacent landowner(s)

Dý others, specify:

c. List t he n ame(s) o f a 11 p erennial s treams t hat j oin t he r eceiving water within t hreemiles downstream of the discharge point:Squaw Creek

d. Do the receiving water characteristics change within three miles downstream o ft he

discharge? (e.g., natural or man-made dams, ponds, reservoirs, etc

W1 Yes E]No

If yes, discuss how:

Changes from a reservoir to a stream

e. Provide general observations of the water body during normal dry weather conditions:

Date and time of observation: Normal reservoir conditions. July 23, 2014

Was water body influenced by stormwater runoff during observations?

E- Yes ZNo

5. GENERAL CHARACTERISTICS OF WATER BODY (Instructions, Page 71)

a. Is the receiving water upstream of the discharges or proposed discharge site influencedby (check as appropriate):

L- oil field activities i-1 urban runoffMV agricultural runoff F-- septic tanksF-1 upstream discharges [-] others, specify below


b. Uses of water body observed or evidences of (check as appropriate):

F-- livestock watering E- contact recreation - irrigation withdrawalF-D non contact recreation E- fishing E- navigation- domestic water supply Z industrial water supply [- picnic park activities- others, specify below

C. Check one of the following to best describe the aesthetics of the receiving water and thesurrounding area:

- Wilderness: outstanding natural beauty; usually wooded or unpastured area: waterclarity exceptional

[R] Natural Area: trees and/or native vegetation common; some development evident(from fields, pastures,dwellings); water clarity discolored

- Common Setting: not offensive, developed but uncluttered; water may be coloredor turbid

FD Offensive: stream does not enhance aesthetics; cluttered; highly developed;dumping areas; water discolored


WORKSHEET 5.0SEWAGE SLUDGE MANAGEMENT AND DISPOSAL

THE FO LLOWING I S R EQUIRED FO R A LL T PDES PER MIT A PPLICATIONSTHAT M EET T HE CONDITIONS AS OUTLINED I N T ECHNICAL REPORT 1.o,ITEM NO. 7.

1. SEWAGE SLUDGE SOLIDS MANAGEMENT PLAN (Instructions, Page 74)

a. Is this a new permit application or an amendment permit application?

El Yes W1 No

b. Does the facility discharge in the Lake Houston watershed?

El Yes W1 No

If yes to either item a or b, indicate by a check mark that a solids management planwas provided with the application. L-

2. SEWAGE SLUDGE MANAGEMENT AND DISPOSAL (Instructions, Pages 74)

a. Please check t he current sludge di sposal m ethod(s). More than one m ethod c an b echecked.

F71 Permitted landfill-- Marketing and distribution by the permittee-- Registered land application site

F-- Composted by the permitteeF-1 Surface disposal site (sludge monofill)--i Transported to another WWTP (written statement or contractual agreement required)

F-- Beneficial land application as authorized in the existing permit

b. Disposal site name: Republic Itasca LandfillTCEQ Permit/Registration Number: 241DCounty where disposal site is located: Hill

c. Method of Transportation (truck, train, pipe, other): TruckHauler Registration Number: ILD981957236 / TXD980796338

Transported in: L-i liquid [I semi-liquid EL semi-solid Z7 solid stateLand application for: EL Reclamation Lj Soil Conditioning

d. If the existing permit contains authorization for sludge land application, composting,marketing and distribution of sludge, and/or sludge lagoons and authorization t orenew the activity is being s ought in the application, the appropriate sections oft heSludge Technical Report must be provided.


3. PERMIT A UTHORIZATION FO R S EWAGE S LUDGE D ISPOSAL(Instructions, Page 75)

Are you requesting new authorization to beneficially land apply sewage sludge at thissite or a site under your direct control?

E- Yes - No

Are you requesting new authorization to market and distribute sewage sludge at thisfacility or a facility under your direct control?

E- Yes W] No

Are you requesting new authorization to compost sewage sludge?

D Yes Z No

Are you requesting new authorization to surface dispose sewage sludge at this site orsite under your direct control?

ED Yes Z No

Are you requesting new authorization to incinerate sewage sludge at this site or siteunder your direct control?

E--Yes IZ-No

If yes to a ny o f the a bove it ems, p rovide t he information required in the S LUDGETECHNICAL REPORT.

New authorization for beneficial land application, incineration, and sludge lagoons inthe TPDES or TLAP permits requires a major a mendmentto t he p ermit. Newauthorization for composting may require a major amendment to the permit. See theinstructions for an explanation whether a major amendment is required or ifauthorization for composting can be added through the renewal process.


Attachment A

Payment of Application Fee


Administrative Report

Rafael Flores Luminant PowerExecutive Vice President P 0 Box 1002

01___ & Chief Nuclear Officer 6322 North FM [email protected] Glen Rose, Texas 76043

Luminant T 254.897.5550C 817.559.0403F 254.897.6652

Delivere'd Via FedEx

TXX# 14111

September 2, 2014

Texas Commission on Environmental QualityFinancial Administration DivisionCashiers Office, MC-21412100 Park 35 CircleAustin, TX 78753

Re: Luminant Generation Company LLCComanche Peak Nuclear Power PlantTPDES Permit No. WQ0001854000Permit Renewal Application Fee

Dear Sir/Madam:

In accordance with the rules and regulations of the Texas Commission on Environmental Quality(TCEQ), Luminant Generation Company LLC hereby submits an application fee in the amount of$2,015.00 for the renewal of Comanche Peak Nuclear Power Plant's TPDES Permit No. WQ0001854000.The permit application is also planned for submittal on September 2, 2014.

Per TCEQ rules and regulations, the permit application will be submitted to the Water Quality Division,Applications Review and Processing Team (MC148). If you have any questions, please contact RyanBayle at 214-875-8294 or via e-mail at [email protected].

Sincerely,

Rafael Flores

By David P. Duncan,Director, Environmental Generation

RMBEnclosures

cc: US Nuclear Regulatory Commission, Document Control Desk, 11555 Rockville Pike, Rockville, MD20852

Attachment B

USGS SITE MAPAND FACILITY MAP


Administrative ReportTechnical Report



RECORD TITLED:USGS SITE MAP. AND FACILITY MAP

HILL ,CITY, TX 2013WITHIN THIS PACKAGE...

D-04



RECORD TITLED:USGS SITE MAP AND FACILITY MAP

NEMO , TX 2013WITHIN THIS PACKAGE...

D-05



RECORD TITLED:ATTACHMENT B, USGS SITE MAP

AND FACILITY MAPCOMANCHE PEAK NUCLEAR POWER

PLANT FACILITY MAPWITHIN THIS PACKAGE...

D-06X

I

Attachment C

General Description


Technical Report

LUMINANT GENERATION COMPANY LPCOMANCHE PEAK NUCLEAR POWER PLANT

GENERAL DESCRIPTION

The Comanche Peak Nuclear Power Plant (CPNPP) is a two-unit nuclear-powered steamelectric generating facility owned and operated by Luminant Generation Company LP(Luminant). The facility is located on the west side of Squaw Creek Reservoir 6322 North FM56,. Glen Rose, TX 75043, Somervell County, Texas. Wastewaters are discharged to SquawCreek Reservoir, thence to Squaw Creek, thence to the Paluxy River in Segment No. 1229 ofthe Brazos River Basin. Squaw Creek Reservoir is the source of all water used for cooling andindustrial use. When needed, make-up water is provided to the reservoir via a pipeline fromnearby Lake Granbury. Potable water is obtained from groundwater and is delivered byCompany-owned on-site wells.

The generating capacity and date of initial commercial operation for each generating unit are asfollows:

Unit Capacity (MW) Date

1 1150 19902 1150 1993

Wastewaters produced at the plant site are collected, treated and discharged via five (5)permitted outfalls. Luminant Generation's operating procedures and wastewater handlingpractices are designed both to comply with all applicable environmental regulations and toprovide operational flexibility wherever practical.

The Company is aware of an increased potential for macroinvertebrate invasion of any plantwater system. In the event of such occurrence, the Company is prepared to treat its water on astatic or flow through basis with the following non-oxidizing biocide: Buckman Bulab 6002Poly[oxyethylene(dimethyliminio)ethylene(dimethyiminio)ethylene dichloride] or GE BetzSpectrus CT-1300 [N-alkyldimethylbenzylammonium chloride (Quat); dodecylguanidinehydrochloride (DGH); ethylene glycol; isopropanol; ethanol]; or by supplementing chlorinationwith ammonia to create chloramines.

The five (5) permitted outfalls are listed below and a description of the wastewater systempertinent to each outfall follows:

Outfall Type of Wastewater

001 Once-through and auxiliary cooling water/previously monitored effluents002 Safe Shutdown Impoundment containing cooling water, low volume

wastes (service water), and stormwater runoff003 Sanitary sewage effluent004 Low volume wastewater/previously monitored effluents104 Metal cleaning wastes

Comanche Peak Nuclear Power PlantGeneral DescriptionPage 2

Outfall 001 (Once-through and Auxiliary Coolingq)

Water from Squaw Creek Reservoir is withdrawn at the intake structure, treated chemically andthen passed through the main condensers or auxiliary heat exchange equipment to condensesteam or cool system components. The intake water is treated with sodium hypochlorite toprevent biofouling and sodium bromide as a chlorine enhancer to improve the hypochloriteconversion and thereby reduce sodium hypochlorite feed rates. Additionally, an ammoniasupplement to chlorination may be utilized to facilitate a more complete conversion from freechlorine to chloramines. Application of these substances is intermittent and does not exceedthe regulatory maximum frequency of two hours/unit/day. A mixture of hydr

Documents

Rafael Flores Luminant Power Luminant - NRC: Home Page · 2014. 9. 24. · Rafael Flores Luminant Power Executive Vice President P 0 Box 1002 & Chief Nuclear Officer 6322 North FM