Upload
harold-milford
View
236
Download
3
Tags:
Embed Size (px)
Citation preview
NetComm Limited 1
NetComm IPDSLAM
NetComm NCT1020 Micro
NCT1000 Mini
IP DSLAM
June 2007
NetComm Limited 2
System Management Software
Connection, Installation & Login
AMCU GUI AAT24B GUI AESG GUI
NetComm Limited 3
•The MCID software provides a Graphical User Interface (GUI), which can be used to configure, maintain, and operate a NCT-1000/1020 across a LAN. The MCID is able to control all the cards.
•Install the MCID management software by following the prompts.
•A shortcut icon of the NCT-1000/1020 MCID will be placed on your desktop. Click the icon to start the CID.
MCID Management Craft Interface Device
Connection & Installation
Shortcut icon of the NCT-1000/1020
MCID
connection
System Management Software
NetComm Limited 4
1.Double click the MCID icon on the desktop to display the login menu.
Enter the following information:•IP Address (default = 172.16.7.100)•Get Community (default = public)•Set Community (default = private)
DSL Concentrator Login
2. Click Start CID to enter the login screen of the device.
Enter Username (default = root)Password (default = root)
System Management Software
NetComm Limited 5
After login the screen will display as below. The figure below has labels for the location of the ACO button, shelf faceplate, and directory tree. The faceplate displays the installed units and their LED status.
MCID Main Menu
Directory Tree
ACO Alarm
Shelf faceplate
System Management Software
NetComm Limited 6
To access the AMCU main control unit, select AMCU from the directory tree or click AMCU from the faceplate.
Contents•System
>Configuration>Administration>VLAN configuration>VLAN PVID>Maintenance>System Software Upgrade
•AMCU Configuration•Current Alarm•History Alarm•Alarm Event•Exiting the AMCU
AMCU GUI
System Management Software
NetComm Limited 7
AAT24B GUI
Contents•Configuration
>Port Information>Bath Configuration>Version>List Slot Configuration>Port Configuration
•Status•Maintenance•Performance•Statistics•Graphical Statics•History Status•Exit
- The AAT24A ADSL 1 card has similar GUI -
System Management Software
NetComm Limited 8
AESG GUI
Contents•Configuration:
version, Card Configuration, Port Configuration
•Spanning Tree: Spanning tree function configuration on Up, Down, Giga Port 1 and Giga Port 2.
•Exiting the AESG
System Management Software
NetComm Limited 9
IP DSLAM Firmware Upgrade
NetComm Limited 10
NCT1000/NCT1020 Firmware Upgrade
Important rules:
1. Keep the TFTP sever and the MCID management software running for performing firmware upgrade.
2. The firmware upgrade sequence MUST be: AAT24A first, AES-G card 2nd and then AMCU the last.
3. For downgrade, you need to use "chkfile 0" to disable check file function by Telneting into the IP DSLAM.
Firmware Upgrade
NetComm Limited 11
NCT1000 / NCT1020 Firmware List
1. AAT24A ADSL1 card firmware V2.03: Aat24A_V2.03.crz
2. AAT24B ADSL2+ card firmware V1.10:Aat24b_V110.crz
3. AES-G Ethernet uplink card firmware V3.3: AesgAP_v33.crz
4. AMCU Management card firmware V9.17N: Amcu-9.17N.crz
MCID Management Software v1.39N1:IP-DSLAM-MCID-V139N1
Firmware Upgrade
NetComm Limited 12
Step 1:
Network Setup for NCT1000 / NCT1020 Firmware Upgrade
IP DSLAM IP Address: 172.16.7.100
Management PC IP Address:
172.16.7.10
IP DSLAM IP Address: 172.16.7.100
Management PC IP Address:
172.16.7.10
Firmware Upgrade
NetComm Limited 13
Step 2:
Set up a TFTP server on the MCID management PC. For example
Step 3:
Set the IP address of the PC to be in the same subnet as that in the IP DSLAM. For example
NCT1000/NCT1020 default IP address: 172.16.7.100/24
Management PC IP address: 172.16.7.10/24Solar Winds-
TFTP-Server
Firmware Upgrade
NetComm Limited 14
Step 4: Upgrade the AAT24B ADSL2+ Card
Login to “DSL Concentrator” MCID management software.
Go to AMCU GUI >System > SW Upgrade > Select “Card Type” = AAT24A “File Type” = AP “TFTP Server IP Address” =
172.17.1.199(This is the IP Address that
is set to the management PC.) “Download File name” =
Aat24aAP_v203.crz (Browse for the firmware file for AAT24A ADSL Line
Card.)Then Click Transmit
Firmware Upgrade
NetComm Limited 15
Step 4: Upgrade the AAT24A ADSL Line Card continued…
The firmware upgrade for AAT24A will take a few minutes. The different status during FW Upgrade are as follows:
Firmware Upgrade
NetComm Limited 16
Firmware Upgrade
For downgrade, you need to use "chkfile 0" to disable check file function by Telneting into the IP DSLAM.
NetComm Limited 17
Step 5: Upgrade/Downgrade the AES-G Ethernet uplink Card
Go to AMCU GUI >System > SW Upgrade > Select “Card Type” = AESG “File Type” = AP “TFTP Server IP Address” = 172.17.1.199
(This is the IP Address that is set to the management PC.) “Download File name” = AesgAP_v33.crz
(Browse for the firmware file for AESG Uplink Card.)
Then Click Transmit
Firmware Upgrade
NetComm Limited 18
Step 5: Upgrade the AESG Ethernet uplink Card continued…
The firmware upgrade for AESG will take a few minutes. The different status during FW Upgrade are as follows:
Firmware Upgrade
NetComm Limited 19
Step 6: Upgrade the AMCU Management Card
Go to AMCU GUI >System > SW Upgrade > Select “Card Type” = AMCU “File Type” = AP “TFTP Server IP Address” =
172.17.1.199(This is the IP Address that
is set to the management PC.) “Download File name” =
Amcu-9.17N.crz (Browse for the firmware
file for AESG Uplink Card.)Then Click Transmit
Firmware Upgrade
NetComm Limited 20
Step 6: Upgrade the AMCU management card continued…
The different status during FW Upgrade are as follows:
Firmware Upgrade
RESET AMCU Card
NetComm Limited 21
Step 7: Reboot the system to take effect on the new firmware for all cards.
Go to AMCU > Maintenance > Reset System through MCIDThe GUI pop-up message are as follows:
IP DSLAM RESTART now takes place.LED Sequence: All off -> Flashed yellow/orange then all red and LEDs on AAT24B self checking one by one. Estimated time for System Reset is approximately 2 minutes.
Firmware Upgrade
NetComm Limited 22
NetComm Limited 23
Step 8: In order to control all the features in the latest firmware AAT24A V2.03 or Aat24B V1.10, AESG V3.3, AMCU V9.17N, the MCID V1.39N1 must be used.
Remove MCID V1.33
NetComm Limited 24
Step 9: Installed MCID V1.39N1 IPDSLAM Management Utility to management the NCT1020 IP DSLAM.
Installed MCID V1.39N1