n 2 Psi Pura Install Guide

7/31/2019 n 2 Psi Pura Install Guide

1/14

SI PURA SPA- 2 0 0 0I n s ta l la t i on Gu ide Vers ion 1 .1

D ocVe r sion : SPA- 2000 - I G- v 1 - 1 - 041 205


2/14

All Rights Reserved.

Copyright 2005

The use, disclosure, modification, transfer, or transmittal of this work for any purpose, in anyform, or by any means, without the written permission of the copyright holder, is strictly

forbidden.

Sipura SPA-2000 I nstallation GuideVersion 1. 1

April 2005

Disc la imer

The content of this manual is subject to change without notice and should not be construed as

a commitment by the manufacturer, distributor, or service provider. This manual is furnishedfor informational use only and the manufacturer, distributor, or service provider assumes noresponsibility for any errors or inaccuracies that may appear herein.

Any services provided through this equipment are not intended to replace or be a substitutefor primary line voice services or Plain Old Telephone Service (POTS) and are not meant toprovide guaranteed Automatic Number Identification or Automatic Location Informationcapabilities associated with 911 or E911 services or to permit access to 411 directoryassistance services. The manufacturer, distributor, or service provider will not be liable forany damages, expenses, liabilities, risks, or harms arising out of or related to the servicesprovided through this equipment.

4.12.2005


3/14

Sipu r a SPA- 2000 I ns ta l l a t i on Gu ide

Page i

Tab le o f Cont en t s

1 . I nt r od uct ion ... . .. . . . .. . . . .. . . . .. . . . .. . . . .. . . . .. . . . .. . . . .. . . . .. . . . .. . . . .. . . . 1 2 .

Gat ew ay Descr ip t ion ... . .. . . . . .. . . . .. . . . . .. . . . . .. . . . . .. . . . .. . . . . .. . . . . . 2

2.1 SPA-2000 Overview........................................................22.2 Connectors and Pinouts...................................................22.3 Accessing the SPA-2000..................................................2

3 . Prov isio ni ng ... . .. . . . .. . . . .. . . . .. . . . .. . . . . .. . . . .. . . . . .. . . . .. . . . . .. . . . .. . . . . . 4 3.1 Upgrading the SPA-2000 FXS Device.................................43.1.1 Setting t he SPA-2000 to Allow Upgrades........ .......... ......... .......... . 43.1.2 Performing the Upgrade.............................................................53.2 General Configuration for Outbound/Inbound Calling ...........73.3

Line-Specific Configuration ..............................................8


4/14


Page 1

1 . I n t r o d u ct i o n

This document is an installation/configuration guide for the Sipura SPA-2000. This Guideprovides instructions for upgrading the SPA-2000 to software version 2.0.13(g). Itdescribes how to configure the SIP parameters, codec settings and analog coefficients foroutbound/inbound calling. It also includes steps for provisioning the device with the useraccount and PIN. These steps will allow users to quickly access the platform and beginmaking/receiving calls.


5/14


Page 2

2 . Ga tew ay Descr ip t ion

The sections below briefly describe the SPA-2000 device.

2.1 SPA-20 00 Over v iewThe SPA-2000 is a 2-port FXS gateway, which allows you to connect two (2) analogphones.

SPA-2000, 2 -por t FXS

2 .2 Connec to r s and Pinou t s

The image below displays the Ethernet (RJ-45) and analog (RJ-11) line pin-outs.

Ethe r ne t ( R J- 45 ) and Ana log ( R J- 11 ) L ine Pin - Ou ts

2.3 Accessing t he SPA-20 00

1. Connect an analog phone to the RJ-45 connector on the SPA-2000.

2. Using the telephone keypad, press the star key four (4) times: * * * * .

3. When you hear an IVR prompt, enter the appropriate code, followed by thepound (#) sign. Refer to the SPA-2000 Menu Op t i ons table on thefollowing page for codes.


6/14


Page 3

SPA-2 00 0 MENU OPTI ONS

Act ion Code User I npu t Behav i or No t es

En t e r I VR Menu **** None Ignore SIT or other tones

until you hear, Sipuraconfiguration menu. Pleaseenter option followed by thepound (#) key, or hang up toexit.

Check DHCP 100 None IVR will announce if DHCP isenabled or disabled.

Set DH CP 101 Enter 1 to enable.

Enter 0 to disable.

Enter option followed by thepound (#) key.

Check I P address 110 None

Set I P Address 111 Enter value using thenumbers on the telephonekeypad. Use the star (*)key when entering adecimal point.

Enter value followed by thepound (#) key. DHCP mustbe Disabled, otherwise, youwill hear the message,Invalid Option if you try toset this value.

Check Net Mask 120 None

Set Net Mask 121 Enter value using thenumbers on the telephonekeypad. Use the star (*)key when entering adecimal point.


Check Gatew ay 130 None

Set Gatew ay 131 Enter value using thenumbers on the telephonekeypad. Use the star (*)key when entering adecimal point.


SPA- 2000 Menu Op t i ons


7/14


Page 4

3 . P rov is ion ing

3.1 Upgrad ing t he SPA-20 00 FXS Dev ice

Before you upgrade the device, please make sure that you: Verify that all phones are on-hook (hung up).

Disable any firewalls on the PC.

Have the PC on the same LAN subnet as the SPA-2000.

Make sure that the Upgrade Enab le field is set to yes on the Prov is ion ing tab(for instructions, refer to section 3.1 .1 Set t i ng t he SPA-2000 t o A l l owUpgrades below).

3 .1 .1 Se t t i ng the SPA-2000 to A l l ow Upg rades

In order for the SPA-2000 to upgrade properly, you must first set the Upgrade Enab le field to y es.

To se t t he Upgrade Enab le f i e ld to yes :

1. Connect to the SPA-2000 by entering the devices IP address in the Webbrowsers Address bar. (For instructions on obtaining the IP address, refer tosection 2 .3 Access ing th e SPA-20 00 on page 2 in this Guide.)

2. Click on the Admi n Log i n link, and then click the advanced configuration link.

Sipu r a Web I n te r fac e Ma in W indow

3. Click the Prov is ion ing tab. and in the Firmware Upgradesection, click theUpgrade Enab le drop-down menu, and select y es.See the screen on the following page.

4. Click the Submi t A l l Changes button at the bottom of the page to save thesettings.


8/14


Page 5

Prov is ion ing Tab Upgr ade Enab le F ie ld Set t o Yes

3 .1 .2 Per fo rm ing th e Upg rade

T o upg rade t h e SPA-2000 :

1. Download the firmware 2.0.13g from the Sipura support site (www.sipura.com) orfrom your reseller to your PC.The Zip file hasex e and b in files. Theb in file is the firmware. Theex e file is the

utility to upgrade the device.

2. Double-click the ex e file.The SPA-1000/2000 Firmware Upgradewindow displays.

3. Click the Cont inue button.The SPA-2000 Firm ware Upgrade w indow displays.

SPA- 2000 F i r mw ar e U pg r ade W indow


9/14


Page 6

4. Enter the IP address of the SPA-2000 that you want to upgrade, and then clickthe OK button.The Confirm Upgrade window displays.

Con f i r m U pg r ade W indow

5. Click the Upgrade button.The Uploading Target Firmw are window displays.

U pgr ade Sta tus W indow

6. When the SPA-2000 has been upgraded successfully, click the OK button in theUpgrade Successful window.

Upgrade Success fu l Wind ow


10/14


Page 7

3 .2 Gene ral Con f i gu ra t i on f o r Ou t bound / I nbound

Cal l ing

T o con f i gu re t h e SPA-2000 f o r ou t bound and i nbound ca l l i ng :

1. Connect to the SPA-2000 by entering the devices IP address in the Webbrowsers Address bar. For instructions on obtaining the IP address, refer to

section 2 .3 Access ing th e SPA-20 00 on page 2 in this Guide.

2. Click on the Admi n Log i n link in the upper right corner of the page, and thenclick the advanced configuration link.

Sipu r a Web I n te r fac e Ma in W indow

3. Click the System tab, and in the Internet Connection Typesection, click theDHCP drop-down menu, and select y es or n o .

Sys tem Tab

4. If you set DHCP to n o , enter the St a t i c I P, NetMask , and Gat ew ay information. If you set DHCP to y es, continue to step 5.



11/14


Page 8

6. Click the Prov is ion ing tab. and in the Firmware Upgradesection, click theUpgrade Enab le drop-down menu, and select n o .See the screen on the following page.


Prov is ion ing Tab Upgr ade Enab le F ie ld Set t o No

3.3 L ine-Spec i f ic Conf igur a t io n

1. Click the L ine1 or L ine2 tab, and in the NAT Set t ings section, change thefollowing setting:

Fie ld Value

NAT Keep Al ive Enab le n o

2. In the Proxy and Reg i s t ra t i on section, change the following setting:

Fie ld Value

Proxy byod1 . ne t 2phone . com

I MPORTANT: For inbou nd serv ice , you m ust se t the Reg is te r f i e ld to

yes ; o t he rw i se, se t i t t o no .


12/14


Page 9

3. In Proxy and Reg i s t ra t i on section as shown in the Line1/2 Window screenbelow, change the following settings.

Fie ld Value

Use Outboun d Prox y n o

Use OB Proxy I n D ia log n o

Make Ca l l Wi th ou t Reg y es

Ans Ca l l Wi t hou t Reg Ye s

DNS SRV Auto Pre f i x no

L ine1 / 2 W indow Pr ox y and Reg i st r a t i on and Subs c r i ber I n fo r m a t i on Sec t i ons

4. In the Subsc r i be r I n f o rm a t i on section, you must enter a Di sp l ay Nam e. Thisvalue can be any alphanumeric string. You may enter the following values,depending on whether your have outbound only or inbound/outbound service:


13/14


Page 10

Serv ice Type Fie ld D isp lay Nam e

Value

Display Name (Line 1) NO_DI D1OUTBOUND SERVI CE ONLY

Display Name (Line 2) NO_DI D2

Display Name (Line 1) Enter your DID.I NBOUND SERVI CE

Display Name (Line 2) Enter your DID.

5. Enter the User I D (account) and Passw ord (PIN).

I MPORTANT: You mus t h ave a d i f f eren t accoun t and P I N f o r L i ne 1

and L ine 2 .

6. Click the Use Au t h I D drop-down menu, and click n o .

7. Scroll to the Aud io Conf igura t ion section as shown in the Line1/2 Window

screen on the following page, and change the following settings:

Fie ld Value

Use Pref Codec Only n o

G729a Enable y es

G723 Enable y es

G726 -16 Enab le n o

G726 -24 Enab le no

G726 -32 Enab le no

G726 -40 Enab le no

DTMF Process I NFO no

DTMF Process AVT yes

DTMF Tx Method AVT


14/14


Page 11

L ine1 / 2 W indow Aud io Con f i gu r a t i on and D ia l P lan Sec t i ons

8. In the Dial Plan section, change the Dial Plan to fit the dialing pattern in yourcountry. The dialed number must start with 1 for US calls and 011 for non-UScalls. Please read the Sipura manual to customize your dial plan.

9. Click the Submi t A l l Changes button to save the settings.

Documents

n 2 Psi Pura Install Guide