DW 605 S12place settingsHalf-load function

Dishwasher Features... ................................. ...3

A Water Softener..................... ......... ........ .....4、

Attention before or after loading the DishwasherBaskets............ ...................... ........... .............9

B Loading the Salt into the Softener.......... .......5、

C Fill the Rinse Aid Dispenser................. ........5、

D Function of Detergent .. ......... ..... .......... .......6、

Wash Cycle Table..... ..... .......... ..... .... ..... .........11Turning on the Appliance........................... .....12Change the Programme....... ..... .. ... ......... ....12....At the end of the Wash Cycle........ ......... ......... .12

Control Panel.. ... ........ .... ... ........ .... ... ........ .... ... .3

The Method Loading Normal Dishware.............10

To review the section on troubleshooting Tipswill help you to solve some common problemsby yourself .

Dear Customer,

Please carefully read this manual before using thedishwasher, it will help you to use and maintain thedishwasher properly.

Pass it on to any subsequent owner of the appliance.This manual contains sections on safety Instructions,Operating Instructions, Installation Instructions andTroubleshooting Tips, etc.

The manufacturer, following a policy of constantdevelopment and updating of the product, maymake modifications without giving prior notice.

This user manual shall also be got from themanufacturer or responsible vendor.

Keep it to refer to it at a later date.

If you can not solve the problems by yourself ,please ask for the help of professional technicians.

Filtering System.......... ..... .... ..... .......... ..... ......13Caring for the Dishwasher..................... .........14.

Before cal ling for service..... ... ........... .... ... . .....23.Error codes..... ................. .............. ..............24.Technical information... ...... ....... .............. .... .25..

.... ..... .......... ..... .... ..... . 15Installation preparation...16Aesthetic panel's dimensions and instal lation

... ..... ......18Tension adjustment of the door spring..... .......... ..... .... ..... . 18Connection of drain hoses

..... .......... ..... .... . 19Dishwasher installation stepsAbout Electricity Connecting...... .......... ..... ......20Cold Water Connection..... ......... ..... .......... ..... 21

This appliance is intended to be used in householdand similar applications such as:-staff kitchen areas in shops, offices and otherworking environments;-farm houses;-by clients in hotels, motels and other residential typeenvironments;-bed and breakfast type environments.This appliance can be used by children aged from 8years and above and persons with reduced physical,sensory or mental capabilities or lack of experienceand knowledge if they have been given supervisionor instruction concerning use of the appliance in asafe way and understand the hazards involved.Children shall not play with the appliance. Cleaningand user maintenance shall not be made by childrenwithout supervision. For EN60335-1This appliance is not intended for use by persons(including children )with reduced physical, sensoryor mental capabilities, or lack of experience andknowledge ,unless they have been given supervisionor instruction concerning use of the appliance by aperson responsible for their safety. For IEC60335-1This appliance is for indoor use only, for householduse only.To protect against the risk of electrical shock, do notimmerse the unit, cord or plug in water or other liquid.Please unplug before cleaning and maintenance theappliance .Use a soft cloth moisten with mild soap, and then usea dry cloth to wipe it again.

（ ）

（ ）

When using your dishwasher,follow the precautions listed below:

This appliance must be earthed. In the event of amalfunction or breakdown, earthing will reduce the riskof anelectric shock by providing a path of leastresistance of electric current. This appliance is equippedwith a cord having an equipment-earthing conductorand a grounding plug.The plug must be plugged into an appropriate outlet thatis installed and earthed in accordance with all localcodes and ordinances.Improper connection of the equipment-earthingconductor can result in the risk of an electric shock.Check with a qualified electrician or servicerepresentative if you are in doubt whether the applianceis properly grounded.Do not modify the plug provided with the appliance;If it does not fit the outlet.Have a proper outlet installed by a qualified electrician.Do not abuse, sit on, or stand on the door or dish rack ofthe dishwasher.Do not operate your dishwasher unless all enclosurepanels are properly in place.Open the door very carefully if the dishwasher isoperating, there is a risk of water squirting out.Do not place any heavy objects on or stand on the doorwhen it is open. The appliance could tip forward.When loading items to be washed:1) Locate sharp items so that they are not likely todamage the door seal;

2) Warning: Knives and other utensils with sharp pointsmust be loaded in the basket with their points down orplaced in a horizontal position.Check that the detergent powder is empty aftercompletion of the wash cycle.Do not wash plastic items unless they are markeddishwasher safe or the equivalent.For plastic items not so marked, check the manufacturer'srecommendations.Use only detergent and rinse additives designed foran automatic dishwasher.Never use soap, laundry detergent, or hand washingdetergent in your dishwasher.Children should be supervised to ensure that they do notplay with the appliance.The door should not be left open, since this could increasethe risk of tripping.If the supply cord is damaged, it must be replaced by themanufacturer or its service agent or a similarly qualifiedperson in order to avoid a hazard.During installation, the power supply must not beexcessively or dangerously bent or flattened.Do not tamper with controls.The appliance is to be connected to the water mains usingnew hose sets and that old hose-sets should not be reused.The maximum number of place settings to be washedis 12.The maximum permissible inlet water pressure is 1MPa.The minimum permissible inlet water pressure is 0.04MPa.

Dispose of the dishwasher packaging materialcorrectly.All packaging materials can be recycled.Plastic parts are marked with the standardinternational abbreviations:PE for polyethylene, e.g. sheet wrapping materialPS for polystyrene, e.g. padding materialPOM polyoxymethylene, e.g. plastic clipsPP polypropylene, e.g. Salt fillerABS Acrylonitrile Butadiene Styrene, e.g. ControlPanel .

Packaging material could be dangerous for children!For disposing of package and the appliance pleasego to a recycling centre. Therefore cut off the powersupply cable and make the door closing deviceunusable.Cardboard packaging is manufactured from recycledpaper and should be disposed in the waste papercollection for recycling.By ensuring this product is disposed of correctly, youwill help prevent potential negative consequencesfor the environment and human health, which couldotherwise be caused by inappropriate waste handlingof this product.For more detailed information about recycling of thisproduct, please contact your local city office and yourhousehold waste disposal service.DISPOSAL: Do not dispose this product as unsortedmunicipal waste. Collection of such waste separatelyfor special treatment is necessary.

With each wash cycle.CompartmentFor programmes with pre-wash only.(Follow the user instructions!)

Electric indicator on control panel (if provided).Check the rinse aid level

(On models with water softener system only.)Electric indicator on control panel (if provided).If there is no salt warning light in the control panel(for some models), you can estimate when to fill the salt intothe softener by the number of cycles the dishwasher has run.

Check the regenerationsalt level

Load the baskets

Select a programme

Turn on the water tap and press the Start/Pause button. The machine will start workingafter about 10 seconds.Running the dishwasher

Switch off the appliance

Turn off the water tap,unload the baskets

Fill the detergent dispenser

Warning: wait a few minutes (about 15 minutes) before unloading the dishwasher to avoid handlingthe dishes and utensils while they are still hot and more susceptible to break.They will also dry better.Unload the appliance, starting from the lower basket.

Changing the programme

Add forgotten dishes in thedishwasher.

Scrape off any large amount of leftover food. Soften remnants of burnt food in pans,then load the baskets. Refer to the dishwasher loading instructions.

Close the door Press the programme button until the selected programme lights up.( See the section entitled Operation instruction )

，“ ”

When the working cycle has finished, the buzzer of thedishwasher will sound 8 times, then stop.Turn off the appliance using the Power button.

If the appliance is switchedoff during a wash cycle.

Open the door carefully.Hot steam may escapewhen the door is opened!

If the appliance is switched off during a wash cycle, when switchedon again, please re-select the washing cycle and operate the dishwasheraccording to the original Power-on state ).

Switch on the appliance Press the Power switch button to switch on the appliance, Open the door.

1.Press the start/pause button to stop the machine.2.Open the door.3.Add the forgotten dishes.4.Close the door, then press the start/pause button, the dishwasher willstart running again after 10 seconds.

For detailed operating method read the corresponding content on the instruction manual.

1. A running cycle can only be modified if it has been running for a short time. Otherwise the detergentmay have already been released and the water already drained. If this is the case, the detergentdispenser must be refilled.2. Press the Start/Pause button ,than press the program button more than 3 seconds to cancel therunning programme.3. Select a new programme.4. Restart the dishwasher.

A BC

before using it for the first time.To get the best performance from your dishwasher, read all operating instructions

Back View

1

23

5

6

78

Front view

4

Dispenser

Cup Shelf

Spray arms

Filter assembly

Inlet pipe connector

Drain pipe

Lower Basket

Inner pipe

Upper Basket1 Salt Container

56

789

10

32

4Adjuster11

99

1.On/Off Button: To turn on/off the power supply.

2. Program Button : To Press the button to select awash Program.

5

.

.Start /Pause button: To start the selectedwashing program or pause the washing programwhen the machine is working.

4.Half load functions Button: To select Half loadfunctions.

3.Delay Button : To Press the button to delay.

6.Power indicator: To show when the power on

7.Program indicators: to show which programyou have chose;

8.Delay indicators: to show the delay time(3h/6h/9h )9.Half load/ salt warning indicators/Rinse Aid indicator:when you choose Half load,the Half load indicator light;when the salt warning light the salt container must onlybe refilled; When rinse aid indicates when the dispenserneeds to be refilled.

11

9 10

The water softener must be set manually, using the water hardness dial.The water softener is designed to remove minerals and salts from the water, which would havea detrimental or adverse effect on the operation of the appliance.The higher the content of these minerals and salts, the harder your water is.The softener should be adjusted according to the hardness of the water in your area. Your local Water Authoritycan advise you on the hardness of the water in your area.

Adjusting Salt ConsumptionThe dishwasher is designed to allow for adjustment in the amount of salt consumed based on the hardness ofthe water used. This is intended to optimise and customise the level o f salt consumption.

1. Press for more than 5 seconds to start the water softenerset model within 60seconds after the appliance was switched on( The Salt andRinse aid warninglights will be on periodically when it get in the set model );

2. Press the to select the proper set according to your local environment,the sets will change in the following sequence: H1->H2->H3->H4->H5->H6;

3. Press the Power button to end the set up model.

Start /Pause button

Start /Pause button

WATER SOFTENERThe hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits willform on the dishes and utensils.The appliance is equipped with a special softener that uses a salt container specifically designed to eliminatelime and minerals from the water.

Contact your local water board for information on the hardness of your water supply.

Please follow the steps below for adjustment in salt consumption.

If your model does not have any water softener, you may skip this section.

Before using your dishwasher for the first time:

A. Set the water softenerB. Add 1.5Kg dishwasher salt and then full fill the salt container with waterC. Fill the rinse aid dispenserD. Fill in detergent

Contact your local water board for information on the hardness of your water supply.

°Clark: British degree

°fH: French degree

°

DH: German degreedH=1.25 Clarke=1.78 fH=0.178mmol/l° °°1

The manufactory setting: H4 (EN 50242)

dH mmol/l

0~90~5 0~0.94 0

10-206-11 1.0-2.0 9

21-3012-17 2.1-3.0 12

20

fH

0~6

7-14

15-21

Clarke

WATER HARDNESS

Selector Position Salt consumption(gram/cycle)

18-22 31-40 22-28 3.1-4.041-6023-34 4.1-6.0 30

60

29-42

35-55 61-98 43-69 6.1-9.8

H1( Rapid )H2(1Hour)

H3(1Hour Rapid )、H4(Glass)

H5(Glass Rapid)、H6(Glass 1Hour)、

1. The salt container must only be refil led when the salt warning light in the control panel comes on.Depending on how well the salt dissolves, the salt warning light may still be on even though thesalt container is filled.If there is no salt warning light in the control panel (for some Models),you can estimate when to fillthe salt into the softener by the cycles that the dishwasher has run.

2. If there are spills of the salt, a soak or a rapid program should be run to remove the excessive salt.

Always use the salt intended for use with dishwasher.The salt container is located beneath the lower basket and should be filled as explainedin the following:

Attention!Only use salt specif ically designed for the use in dishwashers! Every other type ofsalt not specifically designed for the use in a dishwasher, especially table salt, willdamage the water softener. In case of damages caused by the use of unsuitablesalt the manufacturer does not give any warranty nor is liable for any damages caused.Only fil l wi th salt just before starting one of the complete washing programs.This wi ll prevent any grains of salt or salty water, which may have been spilled,remaining on the bottom of the machine for any period of time, which may causecorrosion.

The rinse aid is released during the final rinse to prevent water from forming droplets on your dishes, which canleave spots and streaks. It also improves drying by allowing water to roll off the dishes. Your dishwasher isdesigned to use liquid rinse aids. The rinse aid dispenser is located inside the door next to the detergent dispenser.To fil l the dispenser, open the cap and pour the rinse aid into the dispenser until the level indicator turns completelyblack. The volume of the rinse aid container is about 110ml.

Rinse Aid Dispenser

Function of Rinse AidRinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and streak free drying.

Attention!Only use branded rinse aid for dishwasher. Never fill the rinse aid dispenser with any other substances(e.g. Dishwasher cleaning agent, liquid detergent). This would damage the appliance.

Full fi ll the salt container with water,I t is normal for a smal l amount of water to come out of thesalt container.

A After the lower basket has been removed, unscrew and remove the cap from the salt container.

C

D After f il ling the container , screw the cap tightly back clockwise.E The salt warning light will stop being after the salt container has been fi lled with salt .

F Immediately after f illing the salt into the salt container, a washing program should be startedprogram Otherwise the filter system, pump or other important parts of the machine may be damagedby salty water. This is out of warranty.

(We suggest to use a short).

B Place the end of the funnel (supplied) into the hole and introduce about 1.5kg of dishwasher salt.

To open the dispenser, turn the cap to the "open" (left) arrow and l ift it out.Pour the rinse aid into the dispenser, being careful not to overfill .Replace the cap by inserting it aligned with "open" arrow and turning it to the closed (right) arrow.

Adjusting Rinse Aid DispenserThe rinse aid dispenser has six or four sett ings. Always start with the dispenserset on "4". If spots and poor drying are a problem, increase the amount of r inseaid dispensed by removing the dispenser lid and rotating the dial to "5". If thedishes stil l are not drying properly or are show spots, adjust the dial to the nexthigher lever until your dishes are spot-free. The recommended setting is "4".(Factory value is "4".)

Increase the dose if there are drops of water or lime spots on the dishes after washing.Reduce it if there are sticky whitish stains on your dishes or a bluish film on glassware orknife blades.

123

As the rinse aid diminishes, the size of the black doton the rinse aid level indicator changes, as illustrated below.

Full3 / 4 full1 / 2 full1 / 4 full - Should refill to eliminate spottingEmpty

When to Refill the Rinse Aid DispenserIf there is no rinse-aid warning light in the control panel, you can estimate the amount from the colourof the optical level indicator C located next to the cap. When the rinse-aid container is full, the wholeindicator wil l be dark .As the rinse-aid diminishes, the size of the dark dot decreases. You should never letthe rinse aid level fall 1 / 4 full .

during the next wash. Don't forget to replace the cap before you close dishwasher door.Clean up any rinse aid spil led while during filling with an absorbent cloth to avoid excessive foaming

Detergents with its chemical ingredients are necessary to remove dirt, crush dirt and transport it out of the dishwasher.Most of the commercial quality detergents are suitable for this purpose.

" "

Proper Use of DetergentUse only detergent specifically made for the use in dishwashers. Keep your detergent fresh and dry.Don't put powdered detergent into the dispenser until you're ready to wash dishes.

Attention!

Amount of Detergent to Use

Based on their chemical composition, detergents can be split in two basic types:

Detergent tablets of different brands dissolve at di fferent speeds. For this reason somedetergent tablets cannot dissolve and develop their full cleaning power during shortprograms. Therefore please use long programs when using detergent tablets, toensure the complete removal of detergent residuals.

The dispenser must be refilled before the start of each wash cycle following the instructionsprovided in the wash cycle table . Your dishwasher uses less detergent and rinse aid thanConventional dishwasher. Generally, only one tablespoon of detergent is needed fora normal wash load. More heavily soiled items need more detergent. Always add thedetergent just before starting the dishwasher, otherwise it could get damp and will notdissolve properly.

Concentrated Detergent

Detergent Tablets

Detergent Dispenser

conventional, alkaline detergents with caustic componentslow alkaline concentrated detergents with natural enzymes

Normally new pulverised detergent is without phosphate. Thus the water softener function ofphosphate is not given. In this case we recommend to fill salt in the salt container even whenthe hardness of water is only 6 dH. If detergents without phosphate are used in the case of hard wateroften white spots appear on dishes and glasses. In this case please add more detergent to reachbetter results. Detergents without chlorine do only bleach a little. Strong and coloured spots wil l notbe removed completely. In this case please choose a program with a higher temperature.

°

DetergentsThere are 3 sorts of detergents1.With phosphate and with chlorine2.With phosphate and without chlorine3.Without phosphate and without chlorine

Always add the detergent just before starting each wash cycle.Only use branded detergent aid for dishwasher.

If the lid is closed: press release button. The lid will spring open.

Dishwasher detergent is corrosive!Take care to keep it out of reach of children.

Fill the detergent dispenser with detergent.The marking indicates the dosing levels , asillustrated on the right:

The place of main wash cycle detergent placed.

The place of pre-wash cycle detergent placed.

Please observe the manufacturers dosing and storageRecommendations as stated on the detergent packaging.

Close the lid and press until it locks in place.

If the dishes are heavily soiled, place an additionaldetergent dose in the pre-wash detergent chamber. This detergent will take effect during the pre-wash phase.

AB

Fill in Detergent

You find information about the amount of detergent for the single programme on the last page.Please aware, that according to the level soiling and the specific hardness of water differences are possible.Please observe the manufacturer's recommendations on the detergent packaging.

A B

Cutlery with wooden, horn china ormother-of-pearl handlesPlastic items that are not heat resistantOlder cutlery with glued parts that are nottemperature resistantBonded cutlery items or dishesPewter or cooper itemsCrystal glassSteel items subject to rustingWooden plattersItems made from synthetic fibres

Some types of glasses can becomedull after a large number of washes

Silver and aluminum parts have atendency to discolour during washing

Glazed patterns may fade if machinewashed frequently

Are not suitable Are of limited suitability

Dishes and items of cutlery must not lie ins ide one another, or cover each other.To avoid damage to glasses, they must not touch.Load large items which are most difficult to clean into the lower basket.The upper basket is designed to hold more delicate and lighter dishware such as glasses, coffeeand tea cupsLong bladed knives stored in an upright position are a potential hazard!Long and/or sharp items of cut lery such as carving knives must be positionedhorizontally in the upper basket.Please do not overload your dishwasher. This is important for good results and forreasonable consumption of energy.

Load hollow items such as cups, glasses, pans etc. With the opening facing downwards so thatwater cannot collect in the container or a deep base.

Consider buying utensils which are identified as dishwasher-proof.Use a mild detergent that is described as 'kind to dishes'. If necessary, seek furtherinformation from the detergent manufacturers.For particular items, select a program with as low a temperature as possible.To prevent damage, do not take glass and cutlery out of the dishwasher immediatelyafter the programme has ended.

(For best performance of the dishwasher, follow these loading guidelines.Features and appearance of baskets and cutlery baskets may vary from your model.)

Scrape off any large amounts of leftover food. Soften remnants of burnt food in pans.It is not necessary to rinse the dishes under running water.Place objects in the dishwasher in following way:1.Items such as cups, glasses, pots/pans, etc. are faced downwards.2.Curved items, or ones with recesses, should be loaded aslant so that water can run off.3.All utensils are stacked securely and can not tip over.4.All utensils are placed in the way that the spray arms can rotate freely during washing.

Very small items should not be washed in the dishwasher as they could easily fall out of the basket.

To prevent water dripping from the upper basket into the lower basket, we recommend that youempty the lower basket first and then the upper basket.

The upper basket is designed to hold more delicateand lighter dishware such as glasses, coffee and

tea cups and saucers, as well as plates, small bowlsand shallow pans (as long as they are not too dirty).Position the dishes and cookware so that they willnot get moved by the spray of water.

We suggest that you place large items and the mostdifficult to clean items are to be placed into the lowerbasket: such as pots, pans, lids, serving dishes andbowls, as shown in the figure below. It is preferable toplace serving dishes and lids on the side of the racksin order to avoid blocking the rotation of the top sprayarm.

Pots, serving bowls, etc, must always be placed top down.Deep pots should be slanted to allow water to flow out.

Please be reminded that:

The Bottom Basket features fo lding spikes so that larger or more pots and pans can be loaded.

Folding Spikes of Lower BasketFor better stacking of pots and pans,the spikes can be folded down asshow in the picture right.

Adjusting the Upper BasketThe height of the upper basket can be adjusted in order tocreate more space for large utensils both for the upper/lower basket. The height of the upper basket can beadjusted by placing the wheels on different height of therails. Long items, serving cutlery, salad servers and knivesshould be placed on the shelf so that they do not obstructthe rotation of the spray arms..

Folding back the cup shelivesFor better stacking of pots and pans,the spikes can be folded down asshow in the picture right.

Cutlery should be placed in the cutlery basket with the handles at the bottom. If the rack has side baskets, thespoons should be loaded separately into the appropriate slots, especially long utensils should be placed in thehorizontal position at the front of the upper basket as shown in the picture.

Do not let any item extend through the bottom.Always load sharp utensils with the sharppoint down!

*EN 50242 : This programme is the test cycle. The information for comparabil ity testin accordance with EN 50242, as follows:

Capacity: 12 settingPosit ion Upper basket: upper wheels on railsRinse aid setting: 6Pl:0.49w; Po:0.45w.

Starting a cycle washDraw out the lower and upper basket, load the dishes and push them back.It is commended to load the lower basket first, then the upper one (see the section entitledLoading the Dishwasher ).

Pour in the detergent (see the section entit led Salt, Detergent and Rinse Aid ).Insert the plug into the socket. The power supply is 220-240 VAC /50 HZ, the specificationof the socket is 10A 250VAC. Make sure that the water supply is turned on to full pressure.Close the door, press the ON/OFF Button, and the ON/OFF light will turn on.

“ ”“ ”

Press the program Button , the wash program will be changed as follows direction:

If a program is selected, the response light wil l l ight. Then close the door andIntensive->Normal->ECO->Glass->1Hour ;->Rapid

1

23

45

Press the Start/PauseButton,the dishwasher begins to start.

Means: need to fill rinse into the Rinse-Aid Dispenser.( )

Intensive

Normal

(*EN 50242)

5/25g

5/25g

5/25g

Rapid

Pre-wash(50 )Wash (65 )RinseRinseRinse(65 )Drying

℃℃

℃

Pre-wash( 45 )Wash (55 )RinseRinse (65 )Drying

℃℃

℃

Wash (40 )RinseRinse (45 )

℃

℃

160

185

145

40

1.35

0.91

1.6

0.6

19

15

11

11.5

1HourWash(60 )Rinse (55 )Drying

Pre-wash(50 )℃℃℃

60 1015/25g

20g

GlassRinse

Drying

Pre-washwash(40 )

Rinse(60 )

℃

℃

120 0.85 155/25g

For normally soiled loads,such as , plates,glassesand lightly soiled pans.

pots

For heaviest soiled crockery,and normally soiled potspans dishes etc with driedon soil ing.

、、

A shorter wash for lightlysoiled loads that do notneed drying.

For light ly soiled loads thatdo not need excellent dry ingeffic iency.

For light ly soiled crockeryand glass.

(or )3in1

(or )3in1

(or )3in1

This is standard programme, it issuitable to clean normally soiledtableware and it is the mosteff icient programme in terms ofits combined energy and waterconsumption for that type oftableware.

Pre-washWash (45 )Rinse(65 )Drying

℃℃

If you open the door , the machine will pause. The program light willstop blinking and the buzzer will mooing every minute unless you close the door . Afteryou close the door ,the machine will keep on working after 10 seconds.

dur ing a wash cycle

Premise:A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, thedetergent may have already been released, and the appliance may have already drained the wash water.If this is the case, the detergent dispenser must be refil led (see the section entitled " Loading theDetergent " ).

1

2 Press the Start/Pause button , the machine will be in standby state, press the program button more than3s then you can change the program to the desired cycle setting (see the section entitled " Starting a washcycle. . ." ).

When you press the Start/Pause button to pause during washing, the running indicator willstop blinking and the dishwasher will mooing every minute unless you press theStart/Pause button to start.

If your model has broken remember function, the machine wil l go on to finish the selectedprogram after the power cut.

When the working cycle has finished, the buzzer of the dishwasher will sound for 8 seconds, then stop. Turn offthe appliance using the ON/OFF button, shut off the water supply and open the door of the dishwasher.Wait for a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while theyare still hot and more susceptible to breakage. They will also dry better.

Switch Off the Dishwasher1.Switch off the dishwasher by pressing the ON/OFF button.2.Turn off the water tap!Open the door carefully.Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down around 15 minutesbefore removing from the appliance.Open the dishwasher's door, leave it ajar and wait a few minutes before removing the dishes. In this way theywill be cooler and the drying will be improved.Unloading the dishwasherIt is normal that the dishwasher is wet inside.Empty the lower basket first and then the upper one. This will avoid water dripping from the upper Basket ontothe dishes in the lower one.

A forgotten dish can be added any time before the detergent cup opens.Add forgotten dishes.

Close the door

After the spray arms stop working,you can open the doorcompletely.

23

Open the door a little to stop the washing.

1 45

6

Press the Start/Pause button

Press the Start/Pause button, the dishwasher will runafter 10 seconds.

It is dangerous to open the door when washing,because the hot water may scald you.

The filter prevents larger remnants of food or other objects from getting inside the pump.The residues may block the filter, in this case they must be removed.

The fi lter system consists of a coarse filter,a flat (Main filter)And a microfilter(Fine filter).

Food and soil part icles trapped in this filter are pulverized by aspecia l jet on the lower spray arm and washed down to drain.

Larger items, such as pieces of bones or glass, that could blockthe drain are trapped in the coarse filter. To remove the itemscaught by the filter, gently squeeze the tap on the top of thisfil ter and l ift out.

This filter holds soil and food residues in the sump area andprevents it from being redeposit on the dishes during wash cycle.

Main filter 1

Coarse filter 2

Fine filter 3

2

3

1

Filter assemblyThe filter efficientlyFor best performance and results, the filter must be cleaned regularly. this reason, it is a good idea toremove the larger food particles trapped in the filter after each wash cycle by rinsing the semicircular filter andcup under running water. To remove the fil ter device, pull the cup handle in the upward direction.

removes food particles from the wash water, allowing it to be recycled during the cycle.For

The dishwasher must never be used without the fi lters.Improper replacement of the filter may reduce the performance level of the applianceand damage dishes and utensils.

1

2

Step 1 Turn the filter in anti-clockwise direction,：

Step 2 lift the filter assy up：

When following this procedure from step1 to step 2, the filter system will be removed;when following it from Step 2 to Step 1, the filter system will be installed.

The control panel can be cleaned by using a lightly dampened cloth.After cleaning, make sure to dry it thoroughly.For the exterior, use a good appliance pol ish wax.Never use sharp objects, scouring pads or harsh cleaners on any part of the dishwasher.

Protect Against Freezing

1.Cut off the electrical power to the dishwasher.2.Turn off the water supply and disconnect the water inlet pipe from the water valve.3.Drain the water from the inlet pipe and water valve. (Use a pan to gather the water)4.Reconnect the water inlet pipe to the water valve.5.Remove the filter at the bottom of the tub and use a sponge to soak up water in the sump.

please take frost protection measures on the dishwasher in winter. Every fter washing cycles,please operate as follows

time a：

Cleaning the Filter

Cleaning The Door

To clean the coarse fi lter and the fine filter, use a cleaning brush. Reassemble the fi lter parts as shown in the figureson the last page and reinsert the entire assembly in the dishwasher, positioning it in its seat and pressing downwards.

When cleaning the filters, don't knock on them. Otherwise, the filters could becontorted and the performance of the dishwasher could be decreased.

To clean the edge around the door, you should use only a soft warm, damp cloth.To avoid penetration of water into the door lock and electrical components, do notuse a spray cleaner of any kind.

Never use a spray cleaner to clean the door panel as it may damage the door lockand electrical components.Abrasive agents or some paper towels should not be used because of the risk ofscratching or leaving spots on the stainless steel surface.

Cleaning the Spray Arms

If your dishwasher cannot work because of the ice,please contact professional service persons.

It is necessary to clean the spray arms regularly for hardwater chemicals will clog the spray arm jets and bearings.

- Inspect the filters for blocking after every time the dishwasher has been used.- By unscrewing the coarse fi lter, you can remove the filter system. Remove any food remnants andclean the fi lters under running water.

Remarks:

The entire filter assembly should be cleaned once a week.

To remove the lower spray arm, pull out the spray arm upward.

To remove the upper spray arm, hold the nut, rotate the armclockwise to remove it.

Wash the arms in soapy and warm water and use a soft brush toclean the jets. Replace them after rinsing them thoroughly.

It is recommend that you run a wash cycle with thedishwasher empty and then remove the plug from thesocket, turn off the water supply and leave the door ofthe appliance slightly open. This will help the doorseals to last longer and prevent odours from formingwithin the appliance.

If the appliance must be moved, try to keep it in thevertical position. If absolutely necessary, it can bepositioned on its back.

One of the factors that cause odours to form in thedishwasher is food that remains trapped in the seals.Periodic cleaning with a damp sponge will prevent thisfrom occurring.

Before cleaning or performing maintenance, alwaysremove the plug from the socket.

To clean the exterior and rubber parts of the dishwasher,do not use solvents or abrasive cleaning products.Only use a cloth with warm soapy water.To remove spots or stains from the surface of theinterior, use a cloth dampened with water an a littlevinegar, or a cleaning product made speci fical ly fordishwashers.

Remove the Plug

No Solvents or Abrasive CleaningMoving the Appliance

Seals

After every wash, turn off the water supply to theappliance and leave the door slightly open so thatmoisture and odours are not trapped inside.

After Every Wash When not in Use for a LongTime

The installation of the pipesand electrical equipmentsshould be done by professionals.

Electrical Shock HazardDisconnect electrical powerbeforeinstalling dishwasher.Failure to do so can result indeath or electrical shock.

The installation position of dishwasher should be near the existing inlet and drain hosesand power cord.One side of the cabinet sink should be chosen to facilitate the connection of drain hosesof the dishwasher.

Installation preparation

Note: please check the accompanying installation accessories(hook for aestheticpanel,screw)

●

Please carefully read the installation instruction.● Illustrations of cabinet dimensions and installation position of the dishwasher

Preparations should be made before moving the dishwasher to the installation place.Choose a place near the sink to facilitate the installation of inlet and drain hoses(see figure 1).If dishwasher is installed at the corner of the cabinet, there should be some space(illustrated in figure 2) when the door is opened.

2

1

Minimum space whenthe door is opened

【 】Figure2

Cabinet dimensions

【 】Figure1

Cabinet

Dishwasher

Door ofdishwasher

Minimum space of 50mm

1 The aesthetic wooden panel could be processed according to the Figure 3.

The aesthetic panel shouldbe processed in accordancewith the illustrated dimensions

【 】Figure3

● Aesthetic panel's dimensions and installation

Less than 5mmbetween the top

of dishwasher andcabinet and theouter door alignedto cabinet.

90 ° 90 °

600 mm

820mm

100

580mm

80

Space between cabinetbottom and floor

Electrical, drain andwater supply lineentrances

(Unit: mm)

Installation of aesthetic panel

【 】Figure4a

2 magical paster A and magical paster B be disjoinedon ,magical paster A on the aesthetic wooden panel andfelted magical paster B of the outer door of dishwasher(see f igure 4a). After positioning of the panel , fix the panelonto the outer door by screws and bolts(See figure 4b)

Installation of aestheticwooden panel

【 】Figure4b

. take away the fourshort screws. pin up the four longscrews

1

2

Tension adjustmentof the door spring

【 】Figure5

Tension adjustment of the door spring●

Connection of drain hoses●

The door springs are set at the factory to the proper tension for the outer door.If aesthetic wooden panel are installed, you will have to adjust the door spring tension.Rotate the adjusting screw to drive the adjustor to strain or relax the steel cable(see figure 5).

Door spring tension is correct whenthe door remains horizontal in thefully opened position yet risesto a close with the slight lift of afinger.

，

Insert the drain hose into a drain pipe with a minimum diameter of 40mm, or let i t run into the sink, making sure toavoid bending or crimping it. The top of the hose must be less than 1000mm.

A

CounterFront

Drain pipe

NOTEThe top of the hosemust be less than1000mm.

φ 40mm

B

19

【 】Figure 7

Dishwasher installation steps●

1

2

.3 .4 .5 .6

78

Install the furniture door to the outer door of the dishwasher using the brackets provided. Referto the template for positioning of the brackets.

Adjust the tension of the door springs by using an Allen key turning in a clockwise motion totighten the left and right door springs. Failure to do this could cause damage to your dishwasher(Illustration 2)

Connect the inlet hose to the cold water supplyConnect the drain hose. Refer to diagram (Figure 6)Connect the power cordAffix the condensation strip under the work surface of cabinet. Please ensure the condensation

strip is flush with edge of work surface.Place the dishwasher into position.(Illustration 4)Level the dishwasher. The rear food can be adjusted from the front of the dishwasher by turning

the Allen screw in the middle of the base of dishwasher use an Allen key (Illustration 5A). To adjustthe front feet, use a flat screw driver and turn the front feet until the dishwasher is level (Illustration 5B).9 The dishwasher must be secured in place. There are two ways to do this:A. Normal work surface:Put the installation hook into the slot of the side plane and secure it to the

work surface with the wood screws (Illustration 6).B. Marble or granite work top:Fix the side with Screw. (Illustration 7).

Dishwasher must be level for proper dish rack operation and wash performance.Place a spirit level on door and rack track inside the tub as shown to check that the

dishwasher is level.level the dishwasher by adjusting the three levelling legs individually.When level the dishwasher, please pay attention not to let the dishwasher tip over.

1

23

Illustration of feet adjustment

【 】Figure 8

NOTE:The maximum adjustmentheight of the feet is 50 mm.

Ensure the voltage and frequency of the power being corresponds tothose on the rating plate. Only insert the plug into an electrical socket which is earthedproperly. If the electr ical socket to which the appliance must be connected is notappropriate for the plug , replace the socket, rather than using a adaptors or the l ike asthey could cause overheating and burns.

Please look at the rating label to know the rat ing voltage and connect the dishwasher to the appropriate power supply.Use the required fuse 10 amp, time delay fuse or circuit breaker recommended and provide separate circuit servingonly this appliance.

Check level side to side

Spirit level

Check level Front to Back

For personal safety:Do not use an extension cord or an adapter plugwith this appliance.Do not, under any circumstances, cut or remove theearthingConnection from the power cord.

21

Positioning the Appliance

How to Drain Excess Water From HosesIf the sink is 1000 higher from the floor, the excess water in hoses cannot be drained directlyinto the sink. It will be necessary to drain excess water from hoses into a bowl or suitablecontainer that is held outside and lower than the sink.

Water OutletConnect the water drain hose. The drain hose must be correctly fitted to avoid water leaks.Ensure that the water inlet hose is not kinked or squashed.

Syphon ConnectionInsert the drain hose into a drain pipe with a minimum diameter of 40mm, or let it run into the sink, making sure toavoid bending or crimping it. The top of the hose must be less than 1000mm.

Extension HoseIf you need a drain hose extension, make sure to use a similar drain hose.It must be no longer than 4 metres; otherwise the cleaning effect of the dishwasher could be reduced.

Posit ion the appliance in the desired location. The back should rest against the wall behind it, and the sides,along the adjacent cabinets or walls. The dishwasher is equipped with water supply and drain hoses that canbe positioned either to the right or the left sides to facilitate proper installation.

A hose that attaches to a sink spray can burst if it is installed on the same water line as the dishwasher. If your sinkhas one, it is recommended that the hose be disconnected and the hole plugged.

Pull The safety supply hoses completely out from storage compartment located at rear of dishwasher.

Turn water fully on before starting the dishwasher.

1Tighter the screws of the safety supply hose to the faucet with thread 3/4inch.

The safety supply hose consists of the double walls. The hose's system guarantees its intervention by blocking theflow of water in case of the supply hose breaking and when the air space between the supply hose itself and the outercorrugated hose is full of water.

Turn off the water.

Release the water pressure by depressing the pressure release button. This relieves water pressure and protects you, and theroom, from severe splashing.

Unscrew The safety supply hose from the faucet..321

23

The appliance must be connected to the water mains using new hose-sets.The old hose-sets should not be reused.Water pressure must be between 0,04 MPa and 1 MPa. If the pressure is below theminimum consult our Service Department for advice.

Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure that it is fastened tightly in place.If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that thewater is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blockedand damage the appliance.

The following things should be checked before starting the dishwasher.

The content of this manual is very helpful to the users.After installation, please make sure to keep this manual.

1 The dishwasher is level and fixed properly2 The inlet valve is open3 There is a leakage at the connections of the conducts4 The wires are tightly connected5 The power is switched on6 The inlet and drain hoses are knotted7 All packing materials and printings should be taken out from the dishwasher

22

Fuse blown, or thecircuit breaker acted

Replace fuse or reset circuit breaker. Remove any otherappliances sharing the same circuit with the dishwasher

Spilled rinse-aid Always wipe up rinse-aid spills immediately.

Hard water minerals

The affected items arenot corrosion resistant.

The lid of the softeris looseA sp ay arm isknocking againstan item in a basket

r

Items of crockeryare loose in thewash cabinet

This may be causedby on-site installationor the cross-section ofthe piping.

A programme was notrun after dishwashersalt was added.Traces of salt havegotten into the wash cycle.

To clean the interior, use a damp sponge withdishwasher detergent and wear rubber gloves.Never use any other cleaner than dishwasherdetergent for the risk of foaming or suds.

Always run the quick wash programme .without any crockery in the dishwasher andwithout selecting the Turbo function (if present),after adding dishwasher salt.

Check the lip .Ensure the fix is fine.

Interrupt the programme, and rearrange the itemswhich are obstructing the sp ay arm.r

Interrupt the programme,and rearrange the items of crockery.

This has no influence on the dishwasher function.if in doubt, contact a suitably qualified plumber.

Detergent withcolourant was used

Make sure that the detergent is the one withoutcolourant.

Improper detergent

Make sure the dishwasher is turned on and the door isclosed securely.

Check that the water supply is connected properly andthe water is turned on.

Make sure to close the door properly and latch it.

Make sure the power cord is properly plugged into thewall socket.

Power supply is notturned on

Water pressure is low

Door of dishwashernot properly closed.

Kink in drain hose

Filter clogged

Kitchen sink clogged

Check drain hose.

Check coarse the filter(see section titled )" Cleaning The Filter "

Check the kitchen sink to make sure it is draining well.If the problem is the kitchen sink not draining ,you mayneed a plumber rather than a serviceman for dishwashers.

Use only the special dishwasher detergent to avoid suds.If this occurs, open the dishwasher and let suds evaporate.Add 1 gallon of cold water to the tub. Close and latch thedishwasher, then select any cycle. Dishwasher will drainout the water at the first step.Open the door after drainingis stop and check if the suds is disappeared.Repeat if necessary.

Overflow.

When some malfunctions come on, the appliance will display error codes to warn you:

Longer inlet time.Faucets is not opened, or water intake isrestricted,or water pressure is too low.

Some element of dishwasher leaks .lem

The Rapid light flicker fleetly

The dishes were notloaded correctly.

See notes in " Loading the Dishwasher Baskets ".

Select a more intensive programme.See" Wash Cycle Table ."

Use more detergent, or change your detergent.

Rearrange the items so that the sp ay can rotate freely.r

Clean and/or fit the filter combination correctly.Clean the sp ay arm jets. See "Cleaning the SprayArms".

r

Use less detergent if you have soft water and selecta shortest cycle to wash the glassware and to getthem clean.Use a mild abrasive cleaner to eliminate those marks.

Re-loading the dishes properly.

Load the dishwasher as suggested in the directions.

Increase the amount of rinse-aid/refill the rinse-aiddispenser.

Do not empty your dishwasher immediately afterwashing. Open the door slightly so that the steam canescape. Begin unloading the dishwasher only once the dishes are barely warm to the touch. Empty the lowbasket first. This prevents water form dropping offdishes in the upper basket.In short program the washing temperature is lower.This also lowers cleaning performance. Choosea program with a long washing time.Water drainage is more difficult with these items.Cutlery or dishes of this type are not suitable forwashing in the dishwasher.

The programme wasnot powerful enough.

Not enough detergentwas dispensed.

Items are blockingthe path of sp ay arms.r

The filter combinationin the base of washcabinet is not clean oris not correctly fitted.This may causethe sp ay arm jetsto get blocked.

r

Combination of softwater and too muchdetergent.

Aluminum utensilshave rubbed againstdishes.

Dishes blockdetergent cups.

Improper loading

Too little rinse-aid

Dishes are removedtoo soon

Wrong programhas been selected

Use of cutlery witha low-quality coating

The Glass light flicker fleet ly

Height : 815mmWidth : 598 mmDepth : 570mm( )with the door closed

Water pressure: 0.04-1.0MPaPower supply: see rating labelCapacity: 12 place settings

If overflow occurs, turn off the main water supply before calling a service.If there is water in the base pan because of an overfill or small leak,the water should be removed before restarting the dishwasher.

TEKA

DW 605 S

12

A++

258 kWh

0.91 kWh

0.45 W

0.49 W

3080 li tre

A

185 min

81.5 cm

Yes

59.8 cm

57 cm

1760-2100 W

Sheet of household dishwasher according to EU Directive 1059/2010:

Manufacturer

Type / Description

Standard place settings

Energy efficiency class

Annual energy consumption

Energy consumption of the standard cleaning cycle

Power consumption of off-mode

Power consumption of left-on mode

Annual water consumption

Drying efficiency class

Standard cleaning cycle

Program duration of the standard cleaning cycle

Noise level

Mounting

Height

Could be build-in

Width

Depth (with connectors)

Power consumption

Rated voltage / frequency

A + + + (highest efficiency) to D (lowest efficiency)

Energy consumption 258 kWh per year, based on 280 standard cleaning cycles using cold water fi ll andthe consumption of the low power modes. Actual energy consumption will depend on how the appliance is used.

“ ”

Water consumption 3080 lit re per year, based on 280 standard cleaning cycles. Actual water consumptionwill depend on how the appliance is used.

“ ”

A (highest efficiency) to G (lowest efficiency)

This program is suitable for cleaning soiled normally soiled tableware and that it is themost efficient programme in terms of its combined energy and water consumption forthat type of tableware.

The device meets the European standards and the directives in the current version at delivery:- LVD 2006/95/EC- EMC2004/108/EC- ErP 2009/125/EC

The above values have been measured in accordance with standards under specified operating conditions.Results may vary greatly according to quantity and pollution of the dishes, water hardness,amount of detergent, etc.

The manual is based on the European Union's standards and rules.

Technical Data Sheet

NOTE：

ECO 45℃

49dB(A) re 1 pW

Build-in

AC220-240 V/ 50 Hz

Water pressure (flow pressure) 0.4-10 bar = 0.04-1 Mpa

Austria

Belgium

Bulgaria

Chile

China

Czech Republic

Denmark

Ecuador

Germany

Great Britain

Greece

Hungary

Indonesia

Malaysia

Mexico

Morocco

Netherlands

Norway

Poland

Portugal

Romania

Russia

Singapore

Spain

Sweden

Thailand

Turkey

Ukraine

United Arab Emirates

United Arab Emirates

Venezuela

Vietnam

Küppersbusch Austria

Küppersbusch Belgium S.P.R.L.

Teka Bulgaria EOOD

Teka Chile S.A.

Teka International Trading (Shanghai) Co. Ltd.

Teka CZ S.R.O.

Juvél A/S

Teka Ecuador S.A.

Teka Küchentechnik GmbH

Teka Products Ltd.

Teka Hellas A.E.

Teka Hungary Kft.

PT Teka Buana

Teka Küchentechnik (Malaysia) Sdn Bhd

Teka Mexicana S.A. de C.V.

Teka Maroc S.A.

Teka B.V.

Intra, A.S

Teka Polska Sp. ZO.O.

Teka Portugal S.A.

S.C. Teka Küchentechnik Romania S.R.L.

Teka Rus LLC

Teka Singapore PTE Ltd

Teka Industrial, S.A.

Intra Mölntorp AB

Teka (Thailand) Co. Ltd.

Teka Teknik Mutfak Aletleri Sanayi Ve

Teka Ukranie LLC

Teka Middle East Fze

Teka Küchentechnik U.A.E LLC

Teka Andina S.A.

TEKA Vietnam Co., Ltd.

Eitnergasse, 13

Doomveld Industrie, Asse 3, No. 11 - Boite 7

Blvd. “Tsarigradsko Shosse” 135

Avd El Retiro Parque los Maitenes, 1237. Parque Enea

6/F. Datong Business Center, No. 369 Fuxing Middle Rd.

V Holesovickách, 593

Københavnsvej 222

Parque Ind. California 2, Via a Daule Km 12

Sechsheldener Str. 122

177 Milton Park

Thesi Roupaki - Aspropyrgos

Bajcsy Zsilinszky u. 53

Jalan Menteng Raya, Kantor Taman A9 Unit A3

10 Jalan Kartunis U1/47, Temasya Park, Off Glenmarie

Ferrocarril 200, Esquina Norte 29, Col. Moctezuma

73, Bd. Slimane, Depôt 33, Route de Ain Sebaa

Wijkermeerstraat, 34

Storsand

ul. 3-go Maja 8 / A2

Estrada da Mota - Apdo 533

Sevastopol str., no 24, 5th floor, of. 15

Barklaya str. 6, bld. 3, Barklay plaza center, office 402

Clemenceau Avenue, 83, 01-33/34 UE Square

C/ Cajo,17

Säbyvägen, 8

364/8 Sri-Ayuttaya Road, Phayathai, Ratchatavee

Büyükdere Cad. 24/13

86-e, Bozhenko Str .2nd floor,4th entrance

Building LOB 16, Office 417

Bin Khedia Centre

Ctra. Petare-Santa Lucia, km 3 (El Limoncito)

803 Dai Minh Convention Tower, 8th Floor

1231 Wien

1731 Zellik

1784 Sofia

Pudahuel, Santiago de Chile

200025 Shanghai

182 00 Praha 8 - Liben

DK-4600 Køge

Guayaquil

35708 Haiger

OX14 4SE Milton, Abingdon

193 00 Athens

1065 Budapest

12950 Jakarta

40150 Shah Alam, Selangor Darul Ehsan

15500 Mexico D.F.

Casablanca

2131 HA Hoofddorp

7563 Malvik

05-800 Pruszków

3834-909 Ilhavo, Aveiro

010992 Bucharest Sector 1

121087 Moscow ∙ Russia

239920 Singapore

39011 Santander

734 93 Kolbäck

10400 Bangkok

80290 Mecidiyeköy, Istanbul

03150 Kyiv

P.O. Box 18251 Dubai

P.O. Box 35142 Dubai

1070 Caracas

77 Hoang Van Thai, District 7, Ho Chi Minh

+43 18 668 022

+32 24 668 740

+359 29 768 330

+ 56 24 386 000

+86 2 153 076 901

+420 284 691 940

+45 36 340 288

+593 42 100 311

+49 27 713 950

+44 1 235 861 916

+30 2 109 760 283

+36 13 542 110

+62 215 762 272

+60 376 201 600

+52 5 551 330 493

+212 22 674 462

+ 31 235 656 480

+47 73 980 100

+48 227 383 270

+35 1 234 329 500

+40 212 334 450

+7 495 64 500 64

+65 67 342 415

+34 942 355 050

+46 22 040 300

+66 -26 424 888

+90 2 122 883 134

+380 444 960 680

+971 48 872 912

+971 42 833 047

+58 2 122 912 821

+84 854 160 646

Teka Subsidiaries

Country Subsidiary Address City Phone

“for further information and updated contact adresses, please refer to the corporate website”www.teka.com