Compact Fp Mair It At

7/30/2019 Compact Fp Mair It At

1/19

OverviewThe National Instruments [c]FP-AI-1xx devices are versatile analog

input modules for Compact FieldPoint and FieldPoint that can be

used to measure voltages ranging from the millivolt level to the

120 V high-voltage level in applications such as battery-pack

monitoring, fuel-cell testing, and general measurement from

transducers. These modules can also measure 0 to 20 or 4 to 20 mA

current loops from industrial sensors and transmitters. All the

modules include overranging and onboard diagnostics to ensure

trouble-free installation and maintenance. The modules measure and

linearize signals on-board to return scaled values to your control

or monitoring software. The [c]FP-AI-1xx modules come with

NIST-traceable calibration certificates, ensuring accurate and reliable

analog measurements.

Smart I/O ModulesWith [c]FP-AI-1xx analog input modules, you can directly connect toyour industrial sensors or units under test and get high-accuracy

measurements. The I/O modules filter, calibrate, and scale raw sensor

signals to engineering units, as well as performing self-diagnostics to

look for problems with the module or the wiring. With FieldPoint

modules, your software application reads a linearized, calibrated, and

scaled value from the I/O module, eliminating the error-prone step of

converting binary values to voltage or current values. For increased

accuracy and noise rejection, the [c]FP-AI-110 and [c]FP-AI-111 use a

16-bit delta-sigma ADC with an integrated lowpass filter on each

channel, which you can configure for 50 Hz, 60 Hz, or no rejection.

With high-accuracy 12-bit ADCs or 16-bit delta-sigma ADCs on the

I/O modules, you also get instrument-quality measurements on an

industrially rugged, distributed, embedded system.

[c]FP-AI-1xx modules offer a variety of update rates to fit your

application, ranging from 0.66 to 360 Hz. These rates vary based on

the module used and on the noise filter settings selected on the

module. Overall data throughput depends on software loop speeds

and network speeds. With overranging and underranging, the

[c]FP-AI-1xx analog input modules can measure inputs or sensorsthat are not calibrated to standard ranges. For example, when

configured for an input range of 4 to 20 mA, the modules actually

measure inputs from 3.5 to 21 mA.

Analog Input Modules forCompact FieldPoint and FieldPoint

8 or 16 voltage or current inputs

120 V input range, maximum 0 to 20, 4 to 20 mA input ranges

Built-in signal conditioning 50, 60, and 500 Hz noise rejection

12 and 16-bit resolution Software-configurable input ranges per

channel 2,300 Vrms bank isolation for transient

overvoltage protection Hot-swappable with autoconfiguration -40 to 70 C operating range

NI [c]FP-AI-100, NI [c]FP-AI-102,NI [c]FP-AI-110, NI [c]FP-AI-111

NEW

Input Ranges All-Channel

Module Input Channels Resolution Input Type (Software Configurable per Channel) 50/60 Hz Noise Filter Update Rate

[c]FP-AI-100 8 12 bits Voltage 1 V, 5 V, 15 V, 30 V, 0 to 1 V, 0 to 5 V, 0 to 15 V, 0 to 30 V 360 Hz

Current 0 to 20 mA, 4 to 20 mA, 20 mA

[c]FP-AI-102 8 12 bits Voltage 20 V, 60 V, 120 V, 0 to 20 V, 0 to 60 V, 0 to 120 V 360 Hz

[c]FP-AI-110 8 16 bits Voltage 60 mV, 300 mV, 1 V, 5 V, 10 V, 0 to 1 V, 0 to 5 V, 0 to 10 V 5 Hz to 0.66 Hz

Current 0 to 20 mA, 4 to 20 mA, 20 mA (software selectable) (rate varies with filter settings)

[c]FP-AI-111 16 16 bits Current 0 to 20 mA, 4 to 20 mA, 20 mA 3 Hz to 0.83 Hz

(software selectable) (rate varies with filter settings)


2/19

Thermocouple and RTD Modules for Compact FieldPoint

Overview

The National Instruments cFP-TC-12x and cFP-RTD-12x are versatile

temperature input modules for Compact FieldPoint, used to measure

thermocouples, millivolt-level voltages, thermistors, and 2, 3, and 4-wire

RTDs. They are used in applications such as temperature chamber control,

device testing, and process control. Thermocouples are low-cost, flexible

temperature devices. RTD sensors are used in applications for acquiring

temperatures with high accuracy. Two and 3-wire RTDs work well for

applications with short signal wires and low noise levels; 4-wire RTDs are

well-suited for applications with long signal wires or high noise levels.

All of these I/O modules include overranging and onboard diagnostics to

ensure trouble-free installation and maintenance. The modules measure

and linearize signals on board to return scaled values to your control or

monitoring software. NI cFP-TC-12x and cFP-RTD-12x modules have NIST-

traceable calibration certificates (available on request), ensuring accurate

and reliable analog measurements.

Compact FieldPoint

Compact FieldPoint is designed for industrial control applications that

perform advanced embedded control, data logging, headless operation,

and Ethernet connectivity. Compact FieldPoint, a rugged, reliable NI platform,

is designed for industrial and mobile environments with high shock,

vibration, and temperature extremes.

Isolation

The cFP-TC-125 provides 250 Vrms common-mode voltage protection

between channels, and all cFP-TC-12x and cFP-RTD-12x modules

feature optical bank isolation with 2,300 Vrms of breakdown isolation.

In addition, the cFP-TC-12x and cFP-RTD-12x provide double insulation

for up to 250 Vrms of operational isolation. You can safely use Compact

FieldPoint with the cFP-CB-1 or cFP-CB-3 connector block in applications

where hazardous voltages are present.

8 temperature inputs

Thermocouple or millivolt

2, 3, or 4-wire RTD

Built-in signal conditioning

between channels

250 V common-mode isolation

on TC-125

50 and 60 Hz noise rejection

16-bit resolution

Input ranges configurable in software

for each channel

2,300 Vrms bank isolation for transient

overvoltage protection

Hot-swappable with autoconfiguration

-40 to 70 C operating range

NI cFP-TC-120, NI cFP-TC-125, NI cFP-RTD-122, NI cFP-RTD-124

Module

Input

Channels

Resolution

(bits) Input Type

Input Ranges Software

Configurable per Channel

50/60 Hz

Noise Filter

All-Channel

Update Period

Common-Mode

Between Channels

Safety

Isolation

cFP-TC-120 8 16 Thermocouple J,K,R,S,T,N,E, and B 25 mV, 50 mV, 1.13 s (0.88 Hz) 2,300 Vrmsbank isolationMillivolt 100 mV, -20 to 80 mV

cFP-TC-125 8 16 Thermocouple J,K,R,S,T,N,E, and B 0.22 s (Filter Off)

0.99 s (Filter On)

250 Vrms 2,300 Vrmsbank isolationMillivolt -20 to 80 mV

cFP-RTD-122 8 16 2, 3-Wire RTD Pt 100, Pt 1,000 1.08 s (0.93 Hz) 2,300 Vrmsbank isolationResistance 0 to 400, 0 to 4000

cFP-RTD-124 8 16 2, 4-Wire RTD Pt 100 1.08 s (0.93 Hz) 2,300 Vrmsbank isolationResistance 0 to 400


3/19

Smart I/O ModulesThe cFP-TC-12x and cFP-RTD-12x modules offer 16-bit resolution for

high-accuracy measurements, and you can connect directly to industrial

sensors or units under test with the safety isolation available. The modulesfilter, calibrate, and scale raw sensor signals to engineering units, as

well as perform self-diagnostics to look for problems such as open

thermocouples. With cFP-TC-12x and cFP-RTD-12x modules, your software

application reads a linearized, calibrated, scaled value from the I/O module,

eliminating the error-prone step of converting binary values to temperature.

For increased accuracy and noise rejection, the modules use a

16-bit delta-sigma ADC with an integrated lowpass filter on each

channel, which is configured for 50 and 60 Hz rejection. With high-accuracy

16-bit delta-sigma ADCs on the I/O modules, you also get instrument-quality

measurements on an industrially rugged, distributed, embedded system.

cFP-TC-12x and cFP-RTD-12x modules offer a variety of different updaterates to fit your application, ranging from 0.22 s with filters off and 1.08

to 1.13 s with f ilters enabled. Overall data throughput depends on filter

settings across all channels, software loop speeds, and network speeds.

cFP-TC-120The cFP-TC-120 includes eight differential inputs for thermocouples.

It also provides cold-junction compensation using a thermistor embedded

in the connector block. An onboard microcontroller compensates and

linearizes the thermocouple reading to the NIST IST-90 standard,

using an advanced linearization routine for maximum accuracy.

cFP-TC-125In addition to the thermistor and linearization features of the cFP-TC-120,

the cFP-TC-125 provides 250 Vrms of common-mode rejection, ideal for

applications where differences in voltages might exist between connected

thermocouples. The cFP-TC-125 also provides 0.22 s update rates when

the 50/60 Hz filter is not enabled.

cFP-RTD-122The cFP-RTD-122 includes eight inputs for 2 and 3-wire RTDs.

The module uses a stable current source for sensor excitation and an

onboard microcontroller that linearizes and scales the measurements to

temperature units. You can configure each channel of the module to

return data scaled to temperature (C, F, or K) or resistance. The 3-wire

configuration used with the cFP-RTD-122 eliminates errors caused by

lead wire resistance but does not reduce errors caused by noise. If your

application involves high noise or long wires, you should use 4-wire RTDs

with the cFP-RTD-124.

cFP-RTD-124The cFP-RTD-124 includes eight inputs for 2 and 4-wire RTDs. The module

uses a stable current source for sensor excitation and an onboard

microcontroller that linearizes and scales the measurements to temperature

units. You can configure each channel of the modules to return data scaled

to temperature (C, F, or K) or resistance. Four-wire RTDs used with the

cFP-RTD-124 are ideal for applications involving long signal wires or high

signal noise. The 4-wire configuration eliminates the voltage drop caused

by lead wire resistance and reduces errors caused by noise.

Isothermal Connectivity for the cFP-TC-12xFor maximum accuracy, NI recommends using an isothermal connector

block with the cFP-TC-12x. The cFP-CB-3 isothermal connector block

minimizes the temperature gradient across wiring connections,

improving the accuracy of the cold-junction measurement, and,

therefore, of thermocouple measurements.

Compact FieldPoint I/O Connections

Compact FieldPoint modules include a built-in power distribution bus

that provides multiple power connections on the module. A field-wired

power supply connected to the voltage (V) and common (C) terminals is

internally connected to a power distribution bus that provides additional

breakout terminals for voltage supply (VSUP) and common (COM). These

terminals offer a convenient way to distribute power to field devices that

require external power.

Each cFP-TC-12x input channel has two terminals for differential input:

1. Thermocouple positive input (IN+)2. Thermocouple negative input (IN-)

Each cFP-RTD-122 input channel has three terminals:

1. Excitation output (EXCITE)

2. Sensing input (SENSE)

3. Common input (COM)

Each cFP-RTD-124 input channel has four terminals:

1. Excitation output (EXCITE)

2. Positive sensing input (SENSE+)

3. Negative sensing input (SENSE-)


Thermocouple and RTD Modules for Compact FieldPoint

BUY ONLINE at ni.com or CALL (800) 813 3693 (U.S.)


4/19

OverviewThe National Instruments [c]FP-SG-140 is a versatile resistance bridge

input module for Compact FieldPoint and FieldPoint that can be used to

measure values from resistor bridges including full and half-bridge strain

gauges, quarter-bridge strain gauges (using an external completion

register), and load and torque sensors. The [c]FP-SG-140 includes built-

in excitation,overranging,and onboard diagnostics to ensure trouble-free

installation and maintenance.The module measures and linearizes signals

onboard to return scaled values to your control or monitoring software.

The [c]FP-SG-140 comes with a NIST-traceable calibration certificate,

ensuring accurate and reliable analog measurements.

Smart I/O ModulesWith the SG-140, you can connect directly to industrial sensors or

units under test and get high-accuracy measurements. The module

filters, calibrates, and scales raw sensor signals to engineering units, as

well as performing self-diagnostics to look for problems with the

module or with the wiring. With the SG-140 module, your software

application reads a linearized,calibrated,and scaled value from the I/O

module, eliminating the error-prone step of converting binary values.Because the [c]FP-SG-140 measures in units of millivolts per volt, it

can interface with a wide variety of transducers, such as load cells and

pressure sensors. The module uses a pulsed excitation of up to

21 mA per channel that turns on and off the excitation to each channel.

This reduces self-heating effects and provides more accurate and

repeatable strain measurements. The [c]FP-SG-140 also provides true

ratiometric readings to eliminate errors caused by variations in

excitation voltage. Each channel on the module can be configured for a

different excitation level of 2.5, 5, or 10 V. For increased accuracy and

noise rejection, the [c]FP-SG-140 uses a 16-bit delta-sigma ADC with

an integrated lowpass filter on each channel, which you can configure

for 15, 60, or 240 Hz. With a high-accuracy 16-bit delta-sigma ADC,

you also get instrument-quality measurements on an industrially

rugged, distributed, embedded system.

The [c]FP-SG-140 has three update rates to fit your application,

ranging from 0.87 to 1.11 Hz. These rates vary based on the noise filter

setting selected on the module. Overall data throughput depends on

software loop speeds and network speeds. With overranging and

underranging,the modules can zero out unstrained readings in software

to compensate for field devices with span errors of up to 12 percent.

IsolationThe [c]FP-SG-140 features optical bank isolation with 2,300 Vrms of

breakdown isolation. These Compact FieldPoint and FieldPoint

modules do not have channel-to-channel isolation.

Field I/O Connections

Compact FieldPoint and FieldPoint modules include a built-in powerdistribution bus that provides multiple power connections on the

module. A field-wired power supply connected to the voltage (V) and

common (C) terminals is internally connected to a power distribution

bus that provides additional breakout terminals for voltage supply

(VSUP) and common (COM). These terminals provide a convenient

way to distribute power to field devices that require external power.

Strain Gauge Modules forCompact FieldPoint And FieldPoint

Accept full and half-bridge straingauge inputs directly

Quarter-bridge gauges require externalbridge-completion resistor Compatible with load cells, force

sensors, and torque sensors Built-in signal conditioning

15, 60, and 240 Hz noise rejection Pulsed excitation to prevent

self-heating

16-bit resolution Input ranges software configurable per

channel 2,300 Vrms bank isolation for transientovervoltage protection



NI [c]FP-SG-140 NEW

Input Ranges 15/60/240 Hz

Module Input Channels Resolution (Software Configurable per Channel) Noise Filter All Channel Update Rate

[c}FP-SG-140 8 16 bits 3.5 mV/V, 7.5 mV/V, 30 mV/V, 60 mV/V Software selectable 1.11 to 0.87 Hz (rate varies with filter settings)


5/19

Each input channel on the [c]FP-SG-140 has four terminals:

1. Excitation voltage output (Vexc)

2. Positive signal input (VIN+)

3. Negative signal input (VIN-)


Strain Gauge Modules forCompact FieldPoint And FieldPoint

2 National Instruments Tel: (800) 433-3488 Fax: (512) 683-9300 [email protected] ni.com

Compact FieldPointNI cFP-SG-140 ............................................................777318-140

Recommended Compact FieldPoint System ProductsNI cFP-2020 ..............................................................777317-2020NI cFP-BP-4 ..................................................................778617-04NI cFP-CB-1..................................................................778618-01NI PS-5 Power Supply ..................................................778805-90NI Developer Suite Professional Control Edition..........777906-03

FieldPointNI FP-SG-140..............................................................777518-140

Recommended FieldPoint System ProductsNI FP-1601 ....................................................................777792-01NI FP-TB-1....................... .............................................777519-01PS-4 Power Supply...................................... ..................778586-90NI Developer Suite Standard Control Edition ............777905-03

BUY ONLINE!

Visitni.com/infoand enter cfpsg140, and/or fpsg140.

Ordering Information

Typical for -40 to 70 C unless otherwise noted.

Input CharacteristicsNumber of inputs ............................................. 8 differential

Resolution......................................................... 16 bits, 1 in 65,536

Type of ADC...................................................... Delta-sigma

Filters ............................................................... 15, 60, 240 Hz, user-selectable

Excitation voltage............................................. 2.5, 5, 10 V, user-selectable,

current-limited to 21 mA per c hannel

Bridge configurations....................................... Half and full-bridge circuits, quarter-bridge with external

completion resistor

Gauge factor..................................................... Any (software value)

Input impedance............................................... 20 M

Offset error15 to 35 C................................................. 7.6 V typ, 28 V max

40 to 70 C............................................... 50 V typ, 140 V max

Gain error

15 to 35 C ................................................. 0.06%

40 to 70 C............................................... 0.4%

Input noise (60 Hz filter)

3.5 mV/V................................................. 3 LSBpp 7.5 mV/V................................................. 2 LSBpp

Other ranges..................................................... 1 LSBppAll-channel update periods

15 Hz.......................................................... 1.15 s

60 Hz.......................................................... 0.95 s

240 Hz........................................................ 0.90 s

Isolation VoltageMaximum isolation voltage............................. 250 V rms, Installation Category II

Channel-to-channel isolation........................... No isolation between channels

Transient overvoltage....................................... 2,300 Vrms

Physical CharacteristicsLED indicators

POWER (green).......................................... Power on and self-test passed

READY (green)........................................... Module configured and ready

OVERCURRENT (red).................................. Overcurrent condition on channel

Dimensions (including terminal base).............. 10.9 by 10.7 by 9.1 cm (4.3 by 4.2 by 3.6 in.)

Weight

FP-SG-140.................................................. 140 g (4.8 oz)

cFP-SG-140 ................................................ 110 g (3.7 oz)

Power RequirementPower from network module............................ 1,000 mW

EnvironmentalFieldPoint modules are intended for indoor use only. For outdoor use, they must be mounted inside

a sealed enclosure.

Operating temperature..................................... -40 to 60 C

Storage temperature........................................ -55 to 85 C

Relative humidity ............................................. 10 to 90%, noncondensing

Maximum altitude............................................ 2,000 m; at higher altitudes the isolation voltage

ratings must be lowered.

Pollution degree ............................................... 2

Shock and VibrationThese specifications apply only to Compact FieldPoint. NI recommends Compact FieldPoint if your

application is subject to shock and vibration.

Operating vibration, random(IEC 60068-2-64)........................................ 10500 Hz, 5 grms

Operating vibration, sinusoidal

(IEC 60068-2-6).......................................... 10500 Hz, 5 g

Operating shock

(IEC 60068-2-27)........................................ 50 g, 3 ms half sine, 18 shocks at 6 orientations;

30 g, 11 ms half sine, 18 shocks at 6 orientations

SafetyThis product is designed to meet the requirements of the following standards of safety for electrical

equipment for measurement, control, and laboratory use:

IEC 61010-1, EN 61010-1

UL 3121-1, UL 61010C-1

CAN/CSA C22.2 No. 1010.1

For UL, hazardous location, and other safety certifications, refer to the product label or to ni.com

Electromagnetic CompatibilityCE, C-Tick, and FCC Part 15 (Class A) Compliant

Emissions.......................................................... EN 55011 Class A at 10 m

FCC Part 15A above 1 GHz

Immunity........................................................... EN 61326:1997 +A2:2001, Table 1For EMC compliance, you must operate this device with shielded cabling.

CE ComplianceThis product meets the essential requirements of applicable European Directives, as amended for

CE Marking, as follows:

Low-Voltage Directive (safety)......................... 73/23/EEC

Electromagnetic Compatibility

Directive (EMC) ................................................ 89/336/EEC

Refer to the Declaration of Conformity (DoC) for this product for any additional regulatory compliance

information. To obtain the DoC for this product, visit ni.com/hardref.nsf/and search by model number

or product line.

Specifications

ExcitationVoltage

[c]FP-SG-140

COM

Vin+

Vexc

Vin

Quarter-BridgeStrain Gauges

InputCircuitry

+

ExternalCompletion

Resistor

ExcitationVoltage

[c]FP-SG-140

COM

Vin+

Vexc

Vin

Half-BridgeStrain Gauges

InputCircuitry

+

COM

Vin+

Vexc

Vin ExcitationVoltage

Full-BridgeStrain Gauge

[c]FP-SG-140

InputCircuitry +

Figure 1. Wiring Schematic for the [c]FP-SG-140 Module


6/19

OverviewThe National Instruments [c]FP-AO-2xx devices are versatile analog

output modules for Compact FieldPoint and FieldPoint that can be

used to control valves, gauges, and other industrial actuators. All

modules include overranging and onboard diagnostics to ensure

trouble-free installation and maintenance. The modules accept

engineering units from you, control or monitoring software and

linearize and output scaled signals. The NI [c]FP-AZ-2xx modules

come with NIST-traceable calibration certificates, ensuring accurate

and reliable analog control.

Smart I/O ModulesWith AO-2xx modules, you can directly connect to your industrial

actuators or units under test and get high-accuracy control. The I/O

modules calibrate, and scale engineering units to sensor signals, as

well as performing self-diagnostics to look for problems with the

module or with the wiring such as open current loops. With AO-2xx

modules, your software application writes an engineering value to

the I/O module, eliminating the error-prone step of converting

voltage or current to binary values. The A0-2xx modules have anupdate rate of 200 Hz. Overall data throughput to the controller or

PC depends on the software loop speeds and the network speeds.

The [c]FP-AO-200 includes eight 0 to 20 mA or 4 to 20 mA analog

output channels, generated with a 12-bit DAC. Each output channel

includes a monitoring circuit and LED indicator for open current

loop detection. The AO-200 requires an external power supply

that provides 5 to 24 VDC.

The [c]FP-AO-210 includes eight 0 to 10 V output channels,

generated with a 12-bit DAC. Each channel provides a voltage source

capable of supplying up to 1 mA. You can obtain up to 10 mA by

powering the AO-210 with an optional external power supply of

15 to 30 VDC.

IsolationThe AO-xx series modules feature optical bank isolation with2,300 Vrms of breakdown isolation. These Compact FieldPoint and

FieldPoint modules do not have channel-to-channel isolation.

Field I/O ConnectionsCompact FieldPoint and FieldPoint modules include a built-in power

distribution bus that provides multiple power connections on the

module. A field wired power supply connected to the voltage (V) and

common (C) terminals is internally connected to a power distribution

bus that provides additional breakout terminals for voltage supply

(VSUP) and common (COM). These terminals provide a convenient

way to distribute power to field devices that require external power.

The AO-200 has: 8 current output terminals (IOUT)

16 common terminals (COM)

8 power connections for field devices or current loops (VSUP)

The AO-210 has:

8 voltage output terminals (VOUT)


8 power connections for field devices or current loops (VSUP)

Analog Output Modules forCompact FieldPoint and FieldPoint

8 voltage or current outputs 0 to 10 V

0 to 20, 4 to 20 mA 12 -bit resolution Output ranges software configurable

per channel 2,300 Vrms bank isolation for transient

overvoltage protection Hot swappable with auto-

configuration -40 to 70 C operating range

NI [c]FP-AO-200, NI [c]FP-AO-210 NEW

Module Input Channels Resolution Output Types Output Ranges (Software Configurable per Channel) All Channel Update Rate

[c}FP-AO-200 8 12 bits Current 0 to 20 mA, 4 to 20 mA 200 Hz

[c}FP-AO-210 8 12 bits Voltage 0 to 10 V, (up to 10 mA/ch) 200 Hz


7/19

OverviewThe National Instruments [c]FP-AIO-600 is a versatile combination

analog input and analog output modules for Compact FieldPoint and

FieldPoint that can be used to measure voltages and

0 to 20 or 4 to 20 mA current loops from industrial sensors and

transmitters and to control valves, gauges, and other industrial

actuators. The NI [c]FP-AIO-600 is ideal for low-channel-count

systems or for PID control with high speed I/O. The module has

overranging and onboard diagnostics to ensure trouble-free

installation and maintenance. The [c]FP-AIO-600 measures and

linearizes signals onboard to return scaled values to your control or

monitoring software and accept engineering units from you control or

monitoring software and automatically scale and linearize output

signals. The [c]FP-AIO-600 module comes with a NIST-traceable

calibration certificate, ensuring accurate and reliable analog

measurement and control.

Smart I/O ModulesYou can connect the [c]FP-AIO-600 directly to industrial actuators or

units under test and get high-accuracy measurement and control.

The module calibrates, and scales engineering units to sensor signals,

as well as performing self-diagnostics to look for problems with the

module or with the wiring, such as open current loops. With the

[c]FP-AIO-600s, your software application reads and writes

engineering values from the module, eliminating the error-prone

step of converting voltage or current to binary values.

The module has an update rate of 1.7 kHz. Overall data throughput

depends on the software loop speeds and the network speeds.

[c]FP-AIO-600The [c]FP-AIO-600 includes four 0 to 30 V or 0 to 20/4 to 20 mA

analog inputs and four 0 to 20/4 to 20 mA analog outputs. The

analog inputs and outputs use a 12-bit DAC. Each output channel

includes a monitoring circuit and LED indicator for open current

loop detection. The [c]FP-AIO-600 requires an external powersupply,providing 5 to 30 VDC.

Analog Input/Output Combination Modulesfor Compact FieldPoint and FieldPoint

4 voltage or current inputs 30 V

0 to 20, 4 to 20 mA 4 current outputs 0 to 10 V 0 to 20, 4 to 20 mA

12-bit resolution Input and output ranges software

configurable per channel 2,300 Vrms bank isolation for transient

overvoltage protection Hot swappable with autoconfiguration -40 to 70 C operating range

NI [c]FP-AIO-600 NEW

Input Ranges Output Ranges All Channel

Module Input Channels (Software Configurable per Channel) Output Channels (Software Configurable per channel) Resolution Update Rate

[c}FP-AIO-600 4 Current 0 to 20 mA, 4 to 20 mA 4 Current: 0 to 20 mA, 4 to 20 mA 12 b its 1 .7 kHz

Voltage 5 V, 15 V, 30 V, 0 to 5 V, 0 to 15 V, 0 to 30 V


8/19

Digital Input Modules for Compact FieldPoint and FieldPoint

Overview

The National Instruments [c]FP-DI-3xx devices are versatile digital input

modules. The DI-300, DI-301, and DI-330 are available in the Compact

FieldPoint and FieldPoint product families. The new NI cFP-DI-304 module

is available for Compact FieldPoint systems. You can use these modulesto monitor digital signals ranging from low voltage levels up to 250 V.

They are commonly used to monitor proximity and limit switches,

pushbutton switches, thermostat outputs, relay closures, power circuits,

and TTL devices. All the modules include onboard diagnostics to ensure

trouble-free installation and maintenance.

Digital Input Modules

The [c]FP-DI-3xx modules provide built-in module-to-module isolation to

protect your FieldPoint system and controller or communication interface

from high voltage levels. The DI-300, DI-301, and DI-304 modules use a

common ground plane for all the input channels. Each channel on the DI-300,DI-301, and DI-304 modules include current-limiting circuitry to prevent

module damage when connected directly to a 24 VDC source. The DI-330

uses eight optically isolated input channels so that each digital input has

a separate ground plane, and you can use each channel with a different

voltage potential. Thus, you can connect one channel to a 5 VDC TTL signal

and another signal on the same DI-330 module to a 250 VAC line voltage.

Each channel on the DI-330 includes current-limiting circuitry that limits the

total current to 1.5 mA to prevent damaging the module. All channels on

the DI-3xx modules feature LEDs that indicate the input state of each

channel. The modules feature an all channel update rate of 1 kHz. Overall

data throughput depends on software loop speeds and network speeds.

Isolation

The [c]FP-DI-3xx modules feature bank isolation with 2,300 Vrms of

breakdown isolation. In addition, the DI-330 provides double insulation

for up to 250 Vrms of operational isolation. You can safely use Compact

FieldPoint in applications where hazardous voltages are present when

used with the cFP-CB-1 connector block. You can safely use FieldPoint in

applications where hazardous voltages are present with the FP-TB-x

terminal base. These Compact FieldPoint and FieldPoint modules do not

have channel-to-channel isolation.

Field I/O Connections

Compact FieldPoint and FieldPoint modules include a built-in powerdistribution bus that provides multiple power connections on the module.

A field wired power supply connected to the voltage (V) and common (C)

terminals is internally connected to a power distribution bus that delivers

additional breakout terminals for voltage supply (VSUP) and common

(COM). These terminals offer a convenient way to distribute power

to field devices that require external power.

8,16, or 32 channel inputs

24 VDC inputs 4 to 250 VDC inputs

15 to 250 VAC inputs (50/60 Hz AC)

3 to 250 VAC inputs (1 kHz AC)

2,300 Vrms bank isolation for transientovervoltage protection



FieldPoint Software (included) FieldPoint 5.0 (for all models)

NI [c]FP-DI-300, NI [c]FP-DI-301,NI cFP-DI-304, NI [c]FP-DI-330 NEW!

Module Input Channels Input Ranges Input Type Compatibility Examples

Separate Ground

Plane per Channel

All Channel

Update Rate

Additional

Features[c]FP-DI-300 8 18 to 30 VDC Sinking 24 VDC sourcing devices 1 kHz

[c]FP-DI-301 16 18 to 30 VDC Sinking 24 VDC sourcing devices 1 kHz

cFP-DI-304 32 10 to 30 VDC Sinking 24 VDC sourcing devices 1 kHz Hysteresis

[c]FP-DI-330 8 5 to 48 VDC

5 to 250 VAC

Sinking or sourcing TTL, CMOS, 12 VDC, 24 VDC,

48 VDC, 120/240 VAC/VDC 1 kHz Input current limiting

(1.5 mA)


9/19

Digital Input Modules for Compact FieldPoint and FieldPoint

BUY ONLINE at ni.com or CALL (800) 813 3693 (U.S.)

To next channel

[c]FP-DI-330

VSUP (Ch 0)

COM (Ch 0)

V C

+

InputCircuitryINB (Ch 0)

INA

(Ch 0)Sinking-Output

Device withExternal

Power

VSUP (Ch 1)

COM (Ch 1)

INB (Ch 1)

INA (Ch 1)

VSUP (Ch 2)

COM (Ch 2)

INB

(Ch 2)

INA (Ch 2)

InputCircuitry

InputCircuitry

+

Sourcing-Output

Device withExternalPower

Sinking-OutputDevice

Powered by[c]FP-DI-330

VSUP (Ch 3)

COM (Ch 3)

INB (Ch 3)

INA (Ch 3)

InputCircuitry

Sourcing-OutputDevice

Powered by[c]FP-DI-330

VSUP (Ch n)

COM (Ch n)

INB (Ch n)

INA (Ch n)

InputCircuitry

+ 5-250 V ExternalPower Supply

SwitchTo next channel

[c]FP-DI-300/301/304

VIN (Ch 0)

VSUP (Ch 0)

COM (Ch 0)

V C

InputCircuitry

SourcingOutput

Device withExternalPower

+

VIN (Ch 1)

VSUP (Ch 1)

COM (Ch 1)

InputCircuitry

SourcingOutputDevice

Powered by

[c]FP-DI-30x

VIN (Ch n)

VSUP (Ch n)

COM (Ch n)

InputCircuitry

+

15-30 VDCExternal Power

Supply

Switch

Wiring Schematics for the [c]FP-DI-3xx Modules


Compact FieldPoint

NI cFP-DI-300 ........................... ............................ ...............777318-300

NI cFP-DI-301 ............................. ............................. ............777318-301

NI cFP-DI-304 ............................. ............................. ............777318-304

NI cFP-DI-330 ........................... ............................ ...............777318-330

Recommended Compact FieldPoint System Products

NI cFP-2120 ......................... ........................... ..................777317-2120

NI cFP-BP-4............................................................................778617-04

NI cFP-BP-8............................................................................778617-08

NI cFP-CB-1............................................................................779618-01

NI PS-5 Power Supply ............................ ............................ ..778805-90

NI Developer Suite Professional Control Edition..................777906-03

FieldPoint

NI FP-DI-300 .......................... ............................ ..................777518-300

NI FP-DI-301 ......................... ............................ ...................777518-301

NI FP-DI-330 .......................... ............................ ..................777518-330

Recommended FieldPoint System Products

NI FP-1601 ............................ ............................ ....................777792-01NI FP-TB-1..............................................................................777519-01

NI PS-4 Power Supply ............................ ............................ ..778586-90

NI Developer Suite Control Edition ........................... ...........777905-03

BUY NOW!

For complete product specifications, pricing, and accessoryinformation, call (800) 813 3693 (U.S.) or go to ni.com.


10/19

OverviewThe National Instruments [c]FP-DO-4xx devices are versatile digital

output modules for Compact FieldPoint and FieldPoint that can be

used to control digital signals ranging from 5 to 30 volts. These

modules are commonly used to control indicator lights, external

relays, and CMOS and TTL devices. All the modules include onboard

diagnostics to ensure trouble-free installation and maintenance.

Digital Output ModulesThe DO-4xx modules provide built-in module-to-module isolation

to protect your FieldPoint system and controller or communication

interface from high voltage levels. All the digital output modules use

a common ground plane for the digital output channels.

The DO-400 and DO-401 modules are sourcing digital output

modules capable of providing up to 2 A per channel, with a

maximum power limit across the entire module as explained in the

specifications section.

The DO-403 modules are sinking digital output modules capable

of providing up to 2 A per channel, with a maximum power limit

across the entire module as explained in the specifications section.

The DO-410 modules are sourcing digital output modules capable

of providing up to 1 A per channel. They also feature an electronic fuse

that will prevent damage to the module due to short circuits or other

overcurrent situations. The fuses automatically reset when the output

returns to a normal state. An LED indicates an overcurrent fault.

All the channels on the DO-4xx modules feature LEDs that

indicate the output state of each channel. The modules all feature an

all channel update rate of 20 kHz. Overall data throughput depends

on software loop speeds and network speeds.

IsolationThe DO-4xx modules feature optical bank isolation with 2,300 Vrmsof breakdown isolation. These Compact FieldPoint and FieldPoint

modules do not have channel-to-channel isolation.

Digital Output Modules forCompact FieldPoint and FieldPoint

8 or 16 digital outputs

5 VDC 12 VDC 24 VDC

Fused outputs for short circuitprotection (DO-410)

2,300 Vrms bank isolation for transientovervoltage protection

Hot swappable with autoconfiguration -40 to 70 C operating range

NI [c]FP-DO-400, NI [c]FP-DO-401,NI [c]FP-DO-403, NI [c]FP-DO-410

NEW

Output Current Rating Electronically All Channel

Module Output Channels Output Ranges (see Specifications for More Details) Compatibility Examples Fused Outputs Update Rate

[c]FP-DO-400 8 10 to 30 VDC, sourcing 2 A 12 and 24 VDC 20 kHz

[c]FP-DO-401 16 10 to 30 VDC, sourcing 2 A 12 and 24 VDC 20 kHz

[c]FP-DO-403 16 5 to 30 VDC, sinking 2 A 5, 12, and 24 VDC 20 kHz

[c]FP-DO-410 8 5 to 30 VDC, sourcing 1 A 5, 12, and 24 VDC 20 kHz


11/19

Field I/O ConnectionsThe Compact FieldPoint and FieldPoint modules include a built-in

power distribution bus that provides multiple power connections on the

module. A field-wired power supply connected to the voltage (V) and

common (C) terminals is internally connected to a power distributionbus that provides additional breakout terminals for voltage supply

(VSUP) and common (COM). These terminals provide a convenient way

to distribute power to field devices that require external power.

The DO-400 and DO-410 each have:

8 digital output terminals (VOUT)


8 power connections to power field devices (VSUP)

The DO-401 and DO-403 each have:

16 digital output terminals (VOUT)


8 power connections to power field devices (VSUP)

Digital Output Modules forCompact FieldPoint and FieldPoint

2 National Instruments Tel: (800) 433-3488 Fax: (512) 683-9300 [email protected] ni.com

To next channel

[c]FP-DO-403

+

VOUT (Ch 0)

VSUP (Ch 0)

V C

VSUP (Ch 0)

COM (Ch 0)

Load

VSUP (Ch 1)

COM (Ch 1)

Load

VSUP (Ch n)

COM (Ch n)

Load

5 30 VDCExternal

Power Supply(Optional)

OutputCircuitry

Output

Circuitry

Output

Circuitry

Output

Circuitry

VOUT (Ch n)

VSUP (Ch n)

VOUT (Ch 1)

VSUP (Ch 1)

Figure 1. Wiring Schematics for DO Modules

Compact FieldPointNI cFP-DO-400 ..........................................................777318-400NI cFP-DO-401 ..........................................................777318-401NI cFP-DO-403 ..........................................................777318-403NI cFP-DO-410 ..........................................................777318-410

Recommended Compact FieldPoint System ProductsNI cFP-2020 ..............................................................777317-2020NI cFP-BP-4 ..................................................................778617-04NI cFP-CB-1..................................................................778618-01NI PS-4 Power Supply ..................................................778805-90NI Developer Suite Professional Control Edition..........777906-03

FieldPointNI FP-DO-400 ............................................................777518-400NI FP-DO-401 ............................................................777518-401NI FP-DO-403 ............................................................777518-403NI FP-DO-410 ............................................................777518-410

Recommended FieldPoint System ProductsNI FP-1601 ....................................................................777792-01

NI FP-TB-1....................... .............................................777519-01NI PS-4 Power Supply ..................................................778586-90NI Developer Suite Standard Control Edition ............777905-03

BUY ONLINE!Visitni.com/infoand enter cfpdo400, cfpdo401, cfpdo403, cfpdo410,fpdo400, fpdo401, fpdo403, and/or fpdo410.


To next channel

[c]FP-DO-400/401/410

+

COM (Ch 0)

VOUT (Ch 0)

V C

VSUP (Ch 0)

COM (Ch 0)

Load

COM (Ch 1)

VSUP (Ch 1)

COM (Ch 1)

Load

COM (Ch n)

VSUP (Ch n)

COM (Ch n)

Load

530 VDCExternal

Power Supply

VOUT (Ch 1)

VOUT (Ch n)

OutputCircuitry

OutputCircuitryOutput

Circuitry

OutputCircuitry


12/19

Compact FieldPoint LabVIEW Real-Time Controllers with Ethernet

Overview

National Instruments Compact FieldPoint is a programmable automation

controller (PAC) designed for industrial control applications performing

advanced embedded control, data logging, and network connectivity.

It combines the packaging, specifications, and reliability of a PLC

with the software, flexibility, connectivity, and functionality of a PC.

Compact FieldPoint is a reliable platform designed for rugged industrialenvironments with shock, vibration, and temperature extremes.

National Instruments cFP-21xx controllers run LabVIEW Real-Time,

providing the functionality, connectivity, and flexibility of

National Instruments LabVIEW software on a small industrial platform.

The modular I/O architecture with built-in signal conditioning and

isolation provides direct connectivity to industrial sensors such as analog

voltage, 4 to 20 mA current, thermocouples, RTDs, pressure, strain, flow,

pulse-width modulation (PWM), and 24 V digital I/O. You can use

NI cFP-21xx controllers in intelligent distributed applications requiring

industrial-grade reliability such as process and discrete control

systems to open and close valves, run control loops, log data on a

centralized or local level, perform real-time simulation and analysis, and

communicate over serial and Ethernet networks.

System Basics

A single cFP-21xx controller manages a bank of up to eight

Compact FieldPoint I/O modules. The controller mounts securely on

a metal backplane that provides the communication bus as well as a

solid surface for the Compact FieldPoint I/O modules and controller.

The system is modular; select the I/O modules and connector blocks

or cabling options best suited for your application. Compact FieldPointI/O banks have a number of features for industrial operation, including

2,300 V transient overvoltage protection, a wide temperature range for

operation in extreme environments, backup power supply connections

to protect against primary power failure, and hot-swappable modules

to simplify maintenance and minimize downtime. cFP-21xx controllers

feature an industrial 188 MHz x86 processor that reliably and

deterministically executes your LabVIEW Real-Time applications.

Choose from thousands of built-in LabVIEW functions to build your

multithreaded embedded system for real-time control, analysis, data

logging, and communication. cFP-21xx controllers also offer up to

128 MB of 100 MHz SDRAM and 128 MB of internal nonvolatile storage

and a removable CompactFlash slot. All cFP-21xx controllers feature a

10/100 Mb/s Ethernet port for communication over the network (including

e-mail) and built-in Web (HTTP) and file servers (FTP). Using the LabVIEW

Remote Panel feature, you can automatically publish the front panel

graphical user interface (GUI) for your embedded application so that

multiple clients can monitor or control it remotely using a Web browser.

Rugged LabVIEW Real-Time controller

188 MHz processor andup to 128 MB of SDRAM

Up to 128 MB of nonvolatile storageand 512 MB removable CompactFlash

Ethernet communication for distributedreal-time systems

Dual redundant 11 to 30 VDC powersupply inputs, low power

Up to 4 serial ports (3 RS232 and1 RS485) for communication

Industrial certifications, Class I, Div 2,and -40 to 70 C

Operating Systems Windows 2000/NT/XP

LabVIEW Real-Time

Recommended Software LabVIEW

LabVIEW Real-Time Module

LabVIEW Datalogging andSupervisory Control Module

Driver Software (included) Measurement & Automation Explorer

OPC server (2.0 compliant)

NI cFP-21xx NEW!

Controller SDRAM Memory (MB) Internal Nonvolatile Storage (MB) Removable CompactFlash Ethernet Ports RS232 Ports RS485 Ports

cFP-2120 128 128 1 3 1

cFP-2110 128 64 1 2 0

cFP-2100 64 64 1 1 0


13/19

CompactFieldPointR

eal-Time

EthernetControllerI

nterfaces

IndustrialControlandD

istributedI/O

Overview and ApplicationsCompact FieldPoint is a programmable automation controller (PAC)

designed for industrial control applications performing advanced

embedded control, data logging, headless operation, and Ethernet

connectivit y. It combines the packaging, specifications, and

reliabili ty of a PLC with the software, flexibil ity, connectivity, and

functionali ty of a PC. Compact FieldPoint is our most rugged and

reliable platform and is designed for industrial and mobile

environments with high shock,vibration, and temperature extremes.

Compact FieldPoint banks run LabVIEW Real-Time, providing the

functionality, connectivity, and flexibility of LabVIEW on a small,

rugged, industrial platform. The modular I/O architecture with

built-in signal conditioning and isolation provides directconnectivity to industrial sensors such as analog voltage, 4 to 20 mA

current, thermocouple, RTD, pressure, strain, flow, pulse width

modulation (PWM), and 24 V digital I /O.

Engineers and scientists use the National Instruments cFP-20xx

controllers in intelligent distributed applications requiring

industrial-grade reliabili ty, such as process and discrete control

systems, to open and close valves, run control loops, log data,

perform real-time simulation and analysis, and communicate over

serial, phone, and Ethernet.

SystemConfigurationsA single NI cFP-20xx controller manages a bank of up to eig

Compact FieldPoint analog and digital I /O modules, whic

consti tutes a node. The network module securely mounts on

metal backplane that provides a solid mounting surface for t

Compact FieldPoint bank and forms the communication b

between the controller module and the I/O modules.You choose t

I/O modules and connector block or cabling option that is be

suited for your application.

For more de tails on c onfiguring a Compact FieldPoint system,

see page 517.

Highly Productive SoftwareWhen your application requires powerful functionality and rap

development, the key is flexible software that integrates seamless

with hardware. LabVIEW is an i ndustr y-standard graphic

development environment that provides all the tools necessary create advanced and full-featured measurement and contr

applications. LabVIEW makes it easy to construct simple

complex applications using an extensive palette of functions an

tools from simple analog PID process control loops to hig

channel-count hybrid control systems that combine both analo

and digital components.

Controller Overview Real- time LabVIEW embeddedcontrollers for intelligentindustrial I/O

Stand-alone embedded real-timecontroller or PC-based distributedI/O Ethernet interface

Industrial-grade reliabili ty Automatic self-diagnostics Redundant power supply inputs Isolated communication bus toI/O modules

RS-232 and RS-485 serialports for local device control

Removable CompactFlashfor data logging

Class I Div 2 Ratedfor Hazardous Environments

Operating Systems Windows 2000/NT/XP Real-time performancewith LabVIEW (page 134)

Recommended Software LabVIEW LabVIEW Real-Time Module LabVIEW Datalogging andSupervisory Control Module

Other Compatible Software LabWindows/CVI Measurement Studio Lookout VI Logger

Driver Software (included) Measurement &Automation Explorer


NI cFP-2020, NI cFP-2010, NI cFP-2000

LabVIEW Real-TimeController Interfaces withEthernet

N EW

Internal

DRAM Nonvolite Removable RS-232 RS-485

Module Memory Storage Compact Flash Ethernet Ports Serial Ports Serial Ports

cFP-2020 32 M B 64 M B 1 3 1

cFP-2010 3 2 M B 64 M B 1 2 0

cFP-2000 1 6 M B 32 M B 1 1 0


14/19

Overview and Distributed Applications

National Instruments cFP-180x interfaces connect four or eight

Compact FieldPoint I/O modules to a high-speed Ethernet network or to

an RS232 serial port. With up to 100 Mb/s data communication rates and

event-driven communications, an NI cFP-180x delivers a high-performance

network connection for Compact FieldPoint that is easy to interface with

a PC or PAC-like Compact FieldPoint embedded controller. One or more

cFP-180x interfaces, connected by standard networking equipment, provide

expanded I/O that you can control with a single Compact FieldPoint

controller, see Figure 1. You can also build a PC-based distributed I/O and

control system by connecting two or more cFP-180x devices to your PC.

Hardware Architecture

A cFP-180x provides an integrated network interface (Ethernet or serial)

and a 4 or 8-slot backplane, and it works with the same modules and

connector blocks used in other Compact FieldPoint systems.

Building Ethernet-BasedDistributed I/O Systems

A cFP-180x can communicate with Compact FieldPoint real-time

embedded controllers; any Ethernet-based programmable automation

controller (PAC); and a Windows computer running LabVIEW,

LabWindows/CVI, Measurement Studio, Lookout, or your choice of OPC

client application software. Using a cFP-180x, you can rapidly build

flexible, modular distributed measurement and automation systems.

Ethernet/Serial Interfaces for Compact FieldPoint

Distributed I/O interfaces for Ethernet

and RS232 networks

4 or 8-slot Compact FieldPoint distributed

Ethernet/serial network interfaces

FieldPoint software for rapid distributed

I/O access

Modbus Support

OPC server included

Intelligent diagnostics and maintenance

Industrial specifications for

harsh environments 50 g shock

5 g vibration

-40 to 70 C

Operating Systems Windows 2000/XP

Recommended Software LabVIEW

LabVIEW Datalogging and Supervisory

Control Module

Other Compatible Software LabWindows/CVI

Measurement Studio

Lookout

VI Logger

Driver Software (included) Measurement & Automation Explorer


NI cFP-180x

Compact FieldPoint

Real-Time Controller

NI cFP-1808 Distributed

Network Interfaces

Ethernet

Figure 1. Expansion I/O for Compact FieldPoint Embedded Controller with cFP-1808

Network Interfaces

Figure 2. cFP-1808 Mechanical Dimensions

127 mm(5.00 in.)

441 mm(17.36 in.)

Figure 3. cFP-1804 Mechanical Dimensions

127.0 mm(5.00 in.)

245.9 mm (9.68 in.)


15/19

Compact FieldPoint AccessoriesCompactFlashThe NI cFP-2020 features a slot for removable CompactFlash solid-state nonvolatile

memory for storing your downloaded application or for performing embedded data

logging.NI offers four sizes of CompactFlash cart ridges, ranging from 64 to 512 MB,

which are industr ially rated to withstand temperatures of -40 to 85 C.

64 MB CompactFlash ......................................................................................778622-64

128 MB CompactFlash ..................................................................................778622-128

256 MB Compact Flash ................................................................................778622-256

512 MB CompactFlash ..................................................................................778622-512

RS-232 CablesThe cFP-20xx controllers have the built-in ability to connect to and control external

serial devices such as LCD/keypad displays, touch screens, PLCs, bar code scanners,

scales, and external I /O. For the RS-232 connector on the front of all cFP-20xx

modules,you can use either a standard DB-9 serial cable or, for applications with tightclearances, the right-angle serial connector. The cFP-2010 and cFP-2020 have

additional serial ports on the side of the module with RJ-50 connectors.These RS-232

and RS-485 ports can use either a cable with an RJ-50 connector on one end and a

DB-9 on the other, or an RJ-50 connection to DIN-rail-mounted connector block

with the CB-485A.

Ethernet CablesTwisted-pair, category 5 cable for 10BaseT and 100BaseTX connection connects the

FieldPoint FP-1601 and FP-20xx network interface modules to an Ethernet switch or hub.

1 m ....................................................................................................................182219-01

5 m ....................................................................................................................182219-05

10 m ..................................................................................................................182219-10

Figure 12. Industrial Rated CompactFlash

Serial Cable Cable Length (m) Connector 1 Connector 2 Applicable Terminals Part Number

Right -Angle Serial Cable 1 Right Angle DB-9 DB-9 Front RS-232 189284-02

S8 Serial Cable 1 RJ-50 DB-9 Side RS-232/ RS-485 182845-01




CB-485A 1 RJ-50 Screw terminals, DIN rai l mount Side RS-232/ RS-485 778674-01


16/19

CompactFieldPointBa

ckplanes


istributedI/O

OverviewNational Instruments offers two backplanes for mounting Compact

FieldPoint modules the cFP-BP-4 (4 slots) and the cFP-BP-8

(8 slots). Both backplanes, which are constructed of extruded metal

with grounding lugs on the bottom, feature screw-down connections

for a controller module, four or eight I /O modules, and 37 pin D-Sub

connectors for I /O connections. The backplanes all come with a

cFP-PM-H horizontal mounting bracket, which provides mounting

holes on either side of the backplane so you can mount it to a panel.

For other mounting options, you can purchase a vertical panel

mount, a DIN rail mount, or a 19 in. rack mount separately.

Compact FieldPoint and FieldPointThese backplanes are used with Compact FieldPoint only. Compa

FieldPoint is designed for industrial control applications that perfor

advanced embedded control, data logging, headless operation, an

Ethernet connectivity. Compact FieldPoint is our most rugged a

reliable platform and is designed for industrial and mob

environments with high shock, vibration, and temperature extreme

FieldPoint is a lower-cost distributed I/O system with a variety

communication options besides Ethernet. It is designed to mount o

DIN rails in static applications where the FieldPoint bank is connect

to a PC for data collection, analysis,display, and storage.

4 and 8-slot backplanes Solid metal construction for ruggedinstallations

Panel, DIN rail, and 19 in. rackmounting

Local bus for communicationsand module power

Secure screw mounting for I/Oand control modules


NI cFP-BP-4, NI cFP-BP-8

Compact FieldPoint Backplanes

N EW

Back Plane I/OModule Slots Standard Mounting Hardware

cFP-BP-4 4 cFP-PM -H horizontal panel mount ing bracket

cFP-BP-8 8 cFP-PM -H horizontal panel mount ing bracket

Figure 1. Dimensions of the Compact FieldPoint systems with the cFP-BP-4 and cFP-BP-8 backplanes.

CablingClearance

Cooling Outline51 mm (2 in.)All Around

4 slots =246 mm (9.68 in.)

8 slots =441 mm (17.4 in.)

127mm

(5.0

0in.)

Min.

165mm

(6.5

0in.)

CablingClearance

4 slots =246 mm (9.68 in.)8 slots =441 mm (17.4 in.)

Cooling Outline51 mm (2 in.)

Cooling Outline51 mm (2 in.)

Min.

182mm(7.1

8in.)

106mm(4.1

8in.)


17/19

Compact FieldPoint BackplanesHigh Shock and VibrationTo withstand high levels of shock and vibration, Compact FieldPoint

backplanes are made of extruded metal and provide a rigid

mounting surface for the Compact FieldPoint modules. The

backplane also provides screw-down connections for the controller

module, I/O modules, and connector blocks.

MountingNI offers four mounting options for Compact FieldPoint

backplanes including panel mounting, DIN-rail mounting, and

19 in. rack mounting.

Compact FieldPoint SystemConfigurationCompact FieldPoint I/O modules mount on either the cFP-BP-4 or

cFP-BP-8 backplane. The backplane also contains a control ler

module, which runs embedded LabVIEW Real-Time and can

connect over Ethernet to a PC, to other FieldPoint banks, to Web

browsers, or to other Ethernet devices. The Compact FieldPoint

backplane also provides a 37-pin D-Sub connector to connect your

field signal wir ing for each I/O module. You have three options to

connect f ield wiring to this 37-pin D-Sub connector:

1. Using an integrated connector block such as the cFP-CB-1

or cFP-CB-11;

2.Using a cable to an external connector block mounted on a DIN rail;

3. Making your own custom cable.

For more details on configuring your Compact FieldPoint system,please see 517.

Number Needed to Number Needed to

Mounting Option Description Mount cFP-BP-4 Mount cFP-BP-8

cFP-PM -H Panel mount w ith bolt holes at 1 1

the sides of the backplane.

(included with all backplane)

cFP-PM -V Panel mount w ith bolt holes at the 1 1

top and bottom of the backplane

cFP-RM -8 19 in. rack mount . Features capt ive 1 1

screws for easy mounting and

cutouts for running grounding cables

DIN rai l DIN rai l cl ip for cFP-BP-4 1 2*

mounting clip

* DIN rail mounting is not recommended for the cFP-BP-8NI cFP-BP-4 ..................................................................778617-04NI cFP-BP-8 ..................................................................778617-08

Recommended Compact FieldPoint SystemProductsNI cFP-2020 ..............................................................777317-2020NI cFP-CB-1..................................................................778618-01NI PS-5 Power Supply ..................................................778805-90NI Developer Suite Professional Control Edition..........777906-03

BUY ONLINE!Visitni.com/infoand enter cfppb4, and/or cfppb8.



18/19

CompactFieldPointI/OConnectivityAccessories


istributedI/O

Flexible I/O ConnectivityThe Compact FieldPoint backplane provides standard 37-pin D-Sub connectors f

the signals from the I/O modules. This provides you the flexibil ity to choose t

connectivity method that works best for your application. You have three options

connect field wiring to the 37-pin D-Sub connectors:

1. Using an integrated connector block like the cFP-CB-1, cFP-CB-3, or cFP-CB-11

2. Using a cable to an external connector block mounted on a DIN rail

3. Making your own custom cable.

Integrated Connector BlocksThe most secure and compact connectivity option is to use the integrate

connector blocks. We offer three connector blocks the cFP-CB-1, the cFP-CB-

and the cFP-CB-11.

cFP-CB-1(See Figure 1)The cFP-CB-1 is a general-purpose connector block suitable for any I/O modu

With 36 terminals, the connector block simpl ifies wir ing by eliminating the need

connect more than one wire to a terminal. The cFP-CB-1 also features both a built-

strain relief bar and a separate wire tie connector, making it easy to create secu

wir ing setups for high shock and vibration applications. Although both th

cFP-CB-1 and the cFP-CB-3 feature a built-in thermistor for cold-junctio

compensation, we recommend using the cFP-CB-3 when measuring thermocouple

cFP-CB-3(See Figure 2)The cFP-CB-3 connector block is designed for use with the cFP-TC-120 module.T

cFP-CB-3 uses isothermal construction to minimize thermal gradients on the I/

terminals. This increases the accuracy of the thermistor that is used for cold-junctio

compensation. The cFP-CB-3 also features both a buil t-in strain relief bar and

separate wire tie connector, making it easy to create secure wir ing setups for hi

shock and vibration applications.

cFP-CB-11(See Figure 3)The cFP-CB-11 is a low-profile, general-purpose connector block suitable for any I/

module except the thermocouple module. These connector blocks feature a side ex

for the wir ing, making them a good fit for applications with limited front clearanc

Because the connector blocks are smaller, the cFP-CB-11 is best suited f

applications that use small-gauge wire or that use only a few channels.

CompactFieldPointI/O Connectivity Accessories

Figure 3. cFP-CB-11 Low-Profile Connector Block

Figure 2. cFP-CB-3 Isothermal Connecto r Block f or

Thermocouple M easurement

Figure 1. cFP-CB-1 General-Purpose Connector Block

Connector Number of High Shock Voltage

Block Screw Terminals Built-in CJC and Vibration Limit Applications Part Number

cFP-CB-1 36 250 V General purpose 778618-01

cFP-CB-3 18 250 V Isothermal 778618-03

for thermocouple

cFP-CB-11 37 24 V Low w iring density 778618-11

and low clearance


19/19

Compact FieldPoint Accessories

Mounting Options (see figures 1, 2, and 3)NI offers four mounting options for Compact FieldPoint, including panel mounting, DIN rail mounting, and 19 in. rack mounting.

Power Supplies (see Figure 4)National Instruments offers five DC supplies for Compact FieldPoint systems. You connect the power supply output to the Compact FieldPoint

controller, which regulates, filters, and distributes power to the bank of up to eight I/O modules that it controls. All five power supplies can power an

entire bank of Compact FieldPoint I/O modules. The PS-5 mounts on a DIN rail and is recommended for most Compact FieldPoint installations.

Stand-Alone Controller-Mounting Accessories (see Figure 5)National Instruments offers options for mounting stand-alone Compact FieldPoint controllers. These accessories support applications for redundant

controllers without redundant I/O. The panel and DIN rail-mounting kits also provide mounting options for a stand-alone Compact FieldPoint real-time

controller running LabVIEW Real-Time software. Controller-mounting options include panel and DIN rail-mounting.

Figure 1. cFP-PM-V,

Vertical-Mounting Kit

Figure 2. cFP-PM-H,

Horizontal-Mounting Kit

Figure 3. cFP-RM-8,

Rack-Mounting Kit

Figure 4. PS-5 Power

Supply (24 VDC)

Figure 5. Panel and

DIN Rail-Mounting Kits

Mounting Option Description Quantity Needed to Mount cFP-BP-4 Quantity Needed to Mount cFP-BP-8 Part Number

cFP-PM-H Panel mount with bolt holes at the sides of

the backplane (included with all backplane)

1 1 778616-01

cFP-PM-V Panel mount with bolt holes at the

top and bottom of the backplane

1 1 778688-01

cFP-RM-8 19 in. rack mount; features captive screws for easy

mounting and cutouts for running grounding cables

1 1 778615-01

DIN Rail-Mounting Clip DIN rail clip for cFP-BP-4 1 21 778614-01

1DIN rail mounting is not recommended for the cFP-BP-8.

Model Output Voltage (VDC) Output Current (A) Input Voltage Part Number

PS-1 20 0.8 120 VDC 777567-01

PS-2 24 0.8 P = 1 U.S. 120/Japan 100 VAC

2 Swiss 220 VAC, 3 Australian

4 Universal Euro 240 VAC

5 North American 240 VAC

6 United Kingdom 240 VAC

777584-0P

PS-3 13.8 4 Same as PS-2 777585-0P

PS-4 24 0.625 90 to 260 VAC 50/60 Hz 778586-90

PS-5 24 5 90 to 260 VAC 50/60 Hz 778805-90

Power connects to the cFP-21xx modules, which regulate, filter, and distribute to attached I/O modules.

Model Description Part Number

Panel Panel-mounting kit for stand-alone controllers 779549-01

DIN rail DIN rail-mounting kit for stand-alone controllers 779552-01

BUY NOW!

For complete product specifications, pricing, and accessory information, call (800) 813 3693 (U.S.) or go to ni.com/compactfieldpoint.

Documents

Compact Fp Mair It At