# Ch2 Stallings

• View
221

• Download
1

Embed Size (px)

DESCRIPTION

electromagnetics

### Text of Ch2 Stallings

• Transmission FundamentalsChapter 2 (Stallings Book)

• Electromagnetic Signalis a function of timecan also be expressed as a function of frequencySignal consists of components of different frequencies

• Time-Domain ConceptsAnalog signal - signal intensity varies in a smooth fashion over timeNo breaks or discontinuities in the signalDigital signal - signal intensity maintains a constant level for some period of time and then changes to another constant levelPeriodic signal - analog or digital signal pattern that repeats over times(t +T ) = s(t ) -< t < +where T is the period of the signalAperiodic signal - analog or digital signal pattern that doesn't repeat over time

• Time-Domain Concepts (cont.)Peak amplitude (A) maximum value or strength of the signal over timetypically measured in volts.Frequency (f )Rate, in cycles per second, or Hertz (Hz), at which the signal repeats.

• Time-Domain Concepts (cont.)Period (T)amount of time it takes for one repetition of the signalT = 1/fPhase () - measure of the relative position in time within a single period of a signalWavelength () - distance occupied by a single cycle of the signalEx: Speed of light is v = 3x108 m/s. Then the wavelength is f = v (or = vT).

• Sine Wave ParametersGeneral sine waves(t ) = A sin(2ft + )note: 2 radians = 360 = 1 periodFigure 2.3 shows the effect of varying each of the three parameters(a) A = 1, f = 1 Hz, = 0; thus T = 1s(b) Reduced peak amplitude; A=0.5(c) Increased frequency; f = 2, thus T = (d) Phase shift; = /4 radians (45 degrees)

• Sine Wave Parameters

• Frequency-Domain ConceptsAn electromagnetic signal can be made up of many frequencies.Example: s(t) = (4/p)x(sin(2pft) + (1/3)xsin(2p(3f)t))Fig. 2.4(a) + Fig. 2.4(b) = Fig. 2.4(c)There are two component frequencies: f and 3f.Based on Fourier analysis, any signal is made up of components at various frequencies,in which each component is a sinusoid wave, at different amplitudes, frequencies, and phases.

• Frequency-Domain (cont.)Spectrum - range of frequencies that a signal containsIn Fig. 2.4(c), spectrum extends from f to 3f.Absolute bandwidth - width of the spectrum of a signalIn Fig. 2.4(c), it is 3f f = 2f.Effective bandwidth A signal may contain many frequencies.But most of the energy may concentrate in a narrow band of frequencies.These frequencies are effective bandwidth.

• Fundamental frequency when all frequency components of a signal are integer multiples of one frequency, its referred to as the fundamental frequency(earlier example) f and 3f fund. freq = fThe period of the total signal is equal to the period of the fundamental frequency.refer to Fig. 2.4 again!

• Data vs. SignalSignals - electric or electromagnetic representations of dataData - entities that convey meanings or informationTransmission - communication of data by the propagation and processing of signals

• Approximating Square Wave by Signalsadding a frequency of 5f to Fig. 2.4(c) Fig. 2.5(a)adding a frequency of 7f to Fig. 2.4(c) Fig. 2.5(b)adding all frequencies of 9f, 11f, 13f, ... Fig. 2.5(c), a square waveThis square wave has an infinite number of frequency components, and thus infinite bandwidth.

• Data Rate vs. BandwidthCase I: (Fig. 2.5(a))Let f = 106 cycles/sec = 1 MHzfrequency components: 1f, 3f, 5fabsolute bandwidth = 5f 1f = 4f = 4 MHzdata rate = 2 Mbps (1 bit per 0.5 us)Case II: (Fig. 2.5(a))Let f = 2x106 cycles/sec = 2 MHzfrequency components: 1f, 3f, 5fabsolute bandwidth = 10M 2M = 8 MHzdata rate = 4 Mbps (1 bit per 1/4 us)

• Case III: (Fig. 2.4(c))Let f = 2x106 cycles/sec = 2 MHzfrequencies: 1f, 3fabsolute bandwidth = 6M 2M = 4 MHzdata rate = 4 Mbps (1 bit per 1/4 us)

• Analog and Digital Signal Conversion: Examples

• Some Terms about Channel CapacityData rate - rate at which data can be communicated (bps)Bandwidth - the bandwidth of the transmitted signal as constrained by the transmitter and the nature of the transmission medium (Hertz)NoiseChannel Capacity the maximum rate at which data can be transmitted over a given communication path, or channel, under given conditions Error rate - rate at which errors occur

• Nyquist BandwidthGiven a bandwidth of B, the highest signal transmission rate is 2B:C = 2BEx: B=3100 Hz; C=6200 bpsWith multilevel signalingC = 2B log2 M, where M is the number of discrete signal or voltage levels

• Signal-to-Noise RatioSignal-to-noise ratio (SNR) = power of signal/power of noisetypically measured at a receiverSignal-to-noise ratio (in db)

A high SNR means a high-quality signal.

• Shannon Capacity FormulaThe max. channel capacity:

note: SNR not in db.In practice, only much lower rates are achievedFormula assumes white noise (thermal noise)Impulse noise is not accounted forAttenuation distortion or delay distortion not accounted for

• Classifications of Transmission MediaTransmission MediumPhysical path between transmitter and receiverGuided MediaWaves are guided along a solid mediumE.g., copper twisted pair, copper coaxial cable, optical fiberUnguided MediaProvides means of transmission but does not guide electromagnetic signalsUsually referred to as wireless transmissionE.g., atmosphere, outer space

• General Frequency RangesMicrowave frequency range1 GHz to 40 GHzDirectional beams possibleSuitable for long-distance, point-to-point transmissionUsed for satellite communicationsRadio frequency range30 MHz to 1 GHz Suitable for omnidirectional applicationsInfrared frequency rangeRoughly, 3x1011 to 2x1014 HzUseful in local point-to-point multipoint applications within confined areas

• Multiplexing TechniquesTime-division multiplexing (TDM)Takes advantage of the fact that the achievable bit rate of the medium exceeds the required data rate of a digital signal

Frequency-division multiplexing (FDM)Takes advantage of the fact that the useful bandwidth of the medium exceeds the required bandwidth of a given signal

• Summarysignalanalog vs. digital transmissionschannel capacitytransmission mediaTDM/FDM

Recommended ##### Ch2 Written Assignment - Anurita Dhiman's LEC ... Ch2 Written Assignment Ch2 Written Assignment Wednesday,
Documents ##### REPORT NO. NADC-89048-60 - apps.dtic.mil 2 Pt + CH2=CH-CH2-NH2 -> CH2-CH-CH2-NH2 allylamine Pt Pt CH2-CHCH2NH2
Documents ##### Mr. Schukow's Science Site - Ho atoms 3 and 6. CH2 OH CH2 OH CH2 OH 10 urn OH CH2 OH CH2 About 80 cellulose
Documents Documents