5WG001201 MSOFTX3000 Hardware Data Configuration ISSUE 1.0

7/27/2019 5WG001201 MSOFTX3000 Hardware Data Configuration ISSUE 1.0

http://slidepdf.com/reader/full/5wg001201-msoftx3000-hardware-data-configuration-issue-10 1/20

Wireless Curriculum Development Section

ISSUE

WG001201 MSOFTX3000

hardware data configuration

1.0



2Confidential Information of Huawei.

No Spreading without Permission. Security Level: Internal

Review

This chapter describes the related concepts and

configuration process of MSOFTX3000 equipment

data, including the configuration of hardware basic

information and board data.





References

MSOFTX3000 Operation Manual-Data Configuration

MSOFTX3000 Hardware Description Manual





Course Contents

Chapter 1 overview

Chapter 2 hardware configuration





MSOFTX3000 data configuration procedure

¿ ªÊ ¼

Configuring hardware data

Configuring local office information

Configuring data of interface

Start

Data preparation

Configuring number analysis data

Configuring mobile service data

End

Internal dataconfiguration

Service dataconfiguration





Data configuration Preparation

Command Description

LOF To set offline

SET CWSON: SWT=OFF To disable the alarm switch

SET FMT: STS=OFF To disable the format conversion switchLON To set online

SET CWSON: SWT=ON To enable the alarm switch

SET FMT: STS=ON To enable the format conversion switch

FMT To format data

Power off, power on, and start

loading





Course Contents

Chapter 1 overview

Chapter 2 hardware configuration





Chapter 2 the Chapter Name

2.1 Related Concepts

2.2 Configuration Procedures





MSOFTX3000 Cabinet

Expansion subrack (9U)

Air deflector (2U)

Power distribution subrack (2U)


Air deflector (2U)


Air deflector (2U)


Air deflector (2U)

Expansion Configuration CabinetIntegrated Configuration Cabinet


Air deflector (2U)

Power distribution subrack (2U)


Air deflector (2U)


Air deflector (2U)


Air deflector (2U)

Expansion Configuration Cabinet





Equipment Numbering

Shelf number:0-2

Frame number:0-9

The service processing frame number is set by the DIP switch of the WSIU of the

frame. (off=1,on=0)

The basic frame is numbered 0 and other frames are numbered 1~9 in bottom-up

order.

Switch

Frame number

8 7 6 5 4 3 2 1

0 on on on on on on on on

1 on on on on on on on off

2 on on on on on on off on

3 on on on on on on off off

4 on on on on on off on on

5 on on on on on off on off

6 on on on on on off off on

7 on on on on on off off off

8 on on on on off on on on

9 on on on on off on on off





Equipment Numbering

Slot number

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

W B

S

G

W C C

U

W C C

U

W B

S

G

W I F

M

W C D

B

W I

F

M

W

C D

B

W M G

C

W

A L

U

U P W

R

U P W

R

W C S

U

W C S

U

W S M

U

W

M G

C

W

H S

C

U P W

R

U P W

R

W W P

I

W E P

I

W

H S

C

W C K

I

W C

K

I

W B F

I

W B F

I

W S IU

W

S

IU

Front

Back

W S M

U





Equipment Numbering

Slot number

WSMU boards (and back-insert board WSIU) must be installed

in slots 6 and 8.

WALU must be installed in front slot 16.

WHSC must be installed in back slots 7 and 9, and blank filter

panels are configured in corresponding front slots.

Each UPWR board occupies two slots, and there are two front

UPWR boards and two back UPWR boards. The slot numbers

designated are 17 and 19 fixedly.

Other slots (0~5, 10~15) are installed with service processing

boards (including WCCU, WCSU, WBSG, WIFM, WAFM,

WCDB, WVDB and WMGC).





Equipment Numbering

Module number

WSMU module number: 2~21 (allocated automatically by the

system)

WCCU/WCSU module number: 22~101

WCDB/WVDB module number: 102~131

WMGC/WAFM/WIFM/WBSG/WSGU module number: 132~211





Chapter 2 the Chapter Name

2.1 Related Concepts

2.2 Configu rat ion Procedures





Procedures for configuring equipment data

Procedure Command

Step 1: Add shelf ADD SHF

Step 2: Add frame ADD FRM

Step 3: Add board ADD BRD

Step 4: Configure functions of WCDB board ADD CDBFUNC

Step 5: Configure E1 port information of WEPI

boardADD EPICFG

Step 6: Configure FE port information of

WIFM board

ADD FECFG

Step 7: Clock configurationSET CKICFG

ADD BOSRC

Step 8: Load equipment data -





Parameter relationship of commands for configuring

equipment data

ADD SHF

[Shelf Number]

[Location Title]

[Position Number]

ADD FRM

[Frame Number]

[Shelf Number]

[Position Number]

ADD BRD

[Frame Number]

[Slot Number]

[Module Number]

[Board Type]

ADD EPICFG

[EPI Frame Number]

[EPI Slot Number]

ADD FECFG

[IFM Module Number]

[IP Address]

ADD CDBFUNC

[CDP Module Number]

[Function]





Locking Clock Reference Source through E1

Procedure Command

Step 1: Adding WEPI and WCKI ADD BRD

Step 2: Configuring clock reference source SET CKICFG

Step 3: Configuring E1 information ADD EPICFG

Step 4: Extracting clock reference data from WEPI ADD BOSRC





Locking Clock Reference Source through BITS

Procedure Command

Step 1: Adding WEPI and WCKI ADD BRD

Step 2: Configuring clock reference source SET CKICFG

Step 3: Configuring E1 information ADD EPICFG





Summary

Master hardware data configuration steps

ADD SHF

ADD FRM

ADD BRD

ADD CDBFUNC

ADD EPICFG

ADD FECFG

Clock configuration

Master hardware data configuration method




N S di ith t P i i Security Level: Internal

Documents

5WG001201 MSOFTX3000 Hardware Data Configuration ISSUE 1.0