Upload
triad
View
388
Download
3
Embed Size (px)
Citation preview
1300 INCITE
CaTaloguE v.02
“Quality fire detection and warning equipment,independently supplied and supported”
www.incitefire.com.au • For customer service call 1300 INCITE
CoNTaCT dETaIlsNsW/aCT3/165 Rookwood RoadYagoona NSW 2199Tel: 1300 INCITEFax: 02 9707 1900
vICAxxess Corporate Park120/45 Gilby RoadMount Waverley VICTel: 1300 INCITE
www.incitefire.com.au • For customer service call 1300 INCITE www.incitefire.com.au • For customer service call 1300 INCITE
Incite Fire Pty Ltd is a fully independent fire alarm systems product wholesaler, Sydney & Melbourne based, established in 1999.
Our Objective“Quality fire detection and warning equipment,
independently supplied & supported”
inside Our catalOgue
Conventional Fire Detection We stock the complete range of current & past model Hochiki detectors, as well as a
selection of conventional panels which can be customised to suit your requirements.
Analogue / Addressable Fire Detection Incite Fire is the NSW & ACT distributor of the FireNet analogue panel. We also stock the complete range of Hochiki addressable detectors & field modules.
VESDA Incite Fire is an authorised distributor for the complete range of VESDA aspirated detectors as well as pipework & fittings. Spare parts are available & we can also arrange for the repair of all current model detectors.
Warning Systems A range of OWS and accessories to suit your requirements, as well as EWIS panels configurable to suit any site specifications.
Ancillary Equipment A comprehensive range of ancillary devices including KAC manual call points, a selection of speakers, sounders & strobes. We also stock a range of magnetic door retainers to suit many different applications including the new brass & chrome finish door holders for a more prestigious application.
Special Applications A selection of detection equipment for special applications including flame detectors, firewire, VESDA. Also available is intrinsically safe equipment & detectors suitable for marine applications.
Miscellaneous For convenience we also stock a selection of tools, fixings, enclosures & cable.
Distributors in NSW/ACT and VIC for: • FireNet - Analogue/Addressable Fire Alarm Control Panel • Hochiki - Detectors Analogue & Conventional • VESDA - Range of Aspirated Detectors • Simplex - Evacuation & Warning Systems
For further informationCall: 1300 INCITE (462483)Or visit us at: www.incitefire.com.au
Ne
w C
on
ven
tion
al D
ete
cto
rssl
v-a
s –
Pho
to e
lec
tric
dC
d-a
– T
ype
A t
he
rma
ld
FJ-6
0B –
Typ
e B
th
erm
al
dC
d-C
– T
ype
C t
he
rma
lD
FJ-9
0D –
Typ
e D
th
erm
al
sIJ-
asN
– Io
niz
atio
n
Pre
vio
us
Co
nve
ntio
na
l De
t.SL
K-A
S –
Pho
to e
lec
tric
dC
C-a
– T
ype
A t
he
rma
ld
FE-6
0B –
Typ
e B
th
erm
al
dC
C-C
– T
ype
C t
he
rma
lD
FE-9
0D –
Typ
e D
th
erm
al
SIH
-AM
– Io
niz
atio
n
Ne
w A
na
log
ue
De
tec
tors
alg
-as
– Ph
oto
ele
ctr
ica
Tg-a
s –
The
rma
la
IE-a
s –
Ion
iza
tion
aC
a-E
– M
ulti
Se
nso
ra
CB-
as
– M
ulti
th
erm
al
Pre
vio
us
An
alo
gu
e D
ete
cto
rsa
lB-E
– P
ho
to e
lec
tric
aIa
-E –
Ion
iza
tion
aTa
-E –
The
rma
l
Ne
wC
on
ve
nti
on
al
Ba
ses
YB
o-R
/4a
Pre
vio
us
Co
nv
en
tio
na
lB
ase
s
YB
C-R
/3a
YB
F-R
L/4
AH
AM
Ne
wA
dd
ress
ab
leB
ase
s
YC
A-R
L/3
H2
MY
CA
-RL/
5H
2M
Pre
vio
us
Ad
dre
ssa
ble
Ba
ses
aM
u-B
2M
aM
u-M
BM
YB
F-R
l/3
JM
Ne
wA
na
log
ue
Ba
ses
YB
N-R
/2N
aY
Bo
-R/s
CI
Pre
vio
us
An
alo
gu
eB
ase
s
YB
F-R
l/2
NB
F
HOcHiki detectOr & base cOmpatibility cHart
www.incitefire.com.au • For customer service call 1300 INCITE
CONVENTIONAL PaNEls 4 DETECTors (CurrENT moDEls) 5 DETECTors (PrEvIous moDEls) 7
ANALOGUE PaNEls 8 DETECTors (GTP ProToCol) 10 HaNDHElD ProGrammEr 13 mImIC PaNEls 13 FIElD DEvICEs (GTP ProToCol) 14 sHorT CIrCuIT IsolaTors 15 DETECTors & DEvICEs (HrE ProToCol) 16
VESDA DETECTors 18 rEmoTE uNITs 20 19” raCks 20 FIlTErs 21 soFTwarE & aCCEssorIEs 21 sParE ParTs 22 PIPE & FITTINGs 24
WARNING SYSTEMS EwIs & ows 26 ToNE GENEraTors & amPlIFIErs 26 ows aCCEssorIEs 27 sPEakErs, HorNs & sTrobEs 28 sTrobE sETs, wIP & mCP 30
ANCILLARIES maNual Call PoINTs 32 souNDErs & sTrobEs 33 sPEakErs & HorNs 34 sTrobE sETs & wIP 36 maGNETIC Door HolDErs 37 rEmoTE INDICaTors 38 baTTErIEs 38 PowEr suPPlIEs 39 sIGNs 39 TEsT EquIPmENT 39
SPECIAL APPLICATIONS sPECIal aPPlICaTIoN DETECTors 40 INTrINsICally saFE DETECTors 41 marINE DETECTors 41
MISCELLANEOUS Tools, aErosols, FIxINGs, ENClosurEs 42 ComPoNENTs, INTErFaCE lEaDs & CablE 43
CONTENTS
www.incitefire.com.au • For customer service call 1300 INCITE04 www.incitefire.com.au • For customer service call 1300 INCITE 05
slv-as - Hochiki photo optical smoke detector• Flat response smoke chamber • New chamber design to reduce nuisance alarms
• Dual LED’s for 360° viewing • Rated voltage: 24V DC (working voltage 15-30V DC)
• Low profile, only 48mm (with base) • Only 100mm diameter
• Nominal sensitivity (S)=8.0% Obs/m • Low standby current 35.0μA nominal
• Compatible base YBO-R/4A • SSL listing afp:1649
DCD-a - Hochiki type ‘A’ thermal detector• Electronic linear heat detection • Combination rate of rise & fixed temperature
• Dual LED’s for 360° viewing • Rated voltage: 24V DC (working voltage 15-30V DC)
• Low profile, only 48mm (with base) • Only 100mm diameter
• Alarming temperature 63° • Low standby current 35.0μA nominal
• Compatible base YBO-R/4A • SSL listing afp:1119
DFJ-60b - Hochiki type ‘B’ thermal detector• Fixed temperature thermal detector • Electronic linear heat detection
• Dual LED’s for 360° viewing • Rated voltage: 24V DC (working voltage 15-30V DC)
• Low profile, only 48mm (with base) • Only 100mm diameter
• Alarming temperature 63° • Low standby current 35.0μA nominal
• Compatible base YBO-R/4A • SSL listing afp:1120
DCD-C - Hochiki type ‘C’ thermal detector• Electronic linear heat detection • Combination rate of rise & fixed temperature
• Dual LED’s for 360° viewing • Rated voltage: 24V DC (working voltage 15-30V DC)
• Low profile, only 48mm (with base) • Only 100mm diameter
• Alarming temperature 92° • Low standby current 35.0μA nominal
• Compatible base YBO-R/4A • SSL listing afp:1118
DFJ-90D - Hochiki type ‘D’ thermal detector• Fixed temperature thermal detector • Electronic linear heat detection
• Dual LED’s for 360° viewing • Rated voltage: 24V DC (working voltage 15-30V DC)
• Low profile, only 48mm (with base) • Only 100mm diameter
• Alarming temperature 92° • Low standby current 35.0μA nominal
• Compatible base YBO-R/4A • SSL listing afp:1121
DFG-60blkJ - Hochiki sealed type ‘B’ detector• Waterproof design – rated to IP67 • Fixed temperature sealed thermal detector
• Low profile, only 45mm deep • Suitable for cool rooms, Kitchens, bathrooms etc
• No base required • Alarming temperature 58° - 88°C
• No standby current • Remote lamp ready
• SSL listing afp:661
CO
NV
ENTIO
NA
L DETEC
TOR
S
CurrENT MOdEl
dETECTOrS
CO
NV
ENTI
ON
AL
PA
NEL
S
CONvENTiONal
PaNElS
DCP-002 – Door Control / Local Alarm Panel The Incite DCP-002 is a solution for sliding fire doors and local alarm requirements.
• Self contained and simple to operate • Individual AZF alarm test, fault test, isolate & reset buttons
• 2 fully monitored AZF inputs • Individual AZF alarm, fault & isolate indicators
• Accepts AS1670 detectors • Auxiliary output to interface to other equipment
• Door holder output • Pre warning for door closers on mains failure
• Warning strobe output • Timer for door holder release operation
• Bell output monitored • Internal sounder with isolate switch
• Battery backed
CONvENTiONal PaNElS
An extensive range of Conventional panels are available, including gas control panels
Please contact us on 1300 INCITE for a panel to suit your requirements.
www.incitefire.com.au • For customer service call 1300 INCITE04 www.incitefire.com.au • For customer service call 1300 INCITE 05
slv-as - Hochiki photo optical smoke detector• Flat response smoke chamber • New chamber design to reduce nuisance alarms
• Dual LED’s for 360° viewing • Rated voltage: 24V DC (working voltage 15-30V DC)
• Low profile, only 48mm (with base) • Only 100mm diameter
• Nominal sensitivity (S)=8.0% Obs/m • Low standby current 35.0μA nominal
• Compatible base YBO-R/4A • SSL listing afp:1649
DCD-a - Hochiki type ‘A’ thermal detector• Electronic linear heat detection • Combination rate of rise & fixed temperature
• Dual LED’s for 360° viewing • Rated voltage: 24V DC (working voltage 15-30V DC)
• Low profile, only 48mm (with base) • Only 100mm diameter
• Alarming temperature 63° • Low standby current 35.0μA nominal
• Compatible base YBO-R/4A • SSL listing afp:1119
DFJ-60b - Hochiki type ‘B’ thermal detector• Fixed temperature thermal detector • Electronic linear heat detection
• Dual LED’s for 360° viewing • Rated voltage: 24V DC (working voltage 15-30V DC)
• Low profile, only 48mm (with base) • Only 100mm diameter
• Alarming temperature 63° • Low standby current 35.0μA nominal
• Compatible base YBO-R/4A • SSL listing afp:1120
DCD-C - Hochiki type ‘C’ thermal detector• Electronic linear heat detection • Combination rate of rise & fixed temperature
• Dual LED’s for 360° viewing • Rated voltage: 24V DC (working voltage 15-30V DC)
• Low profile, only 48mm (with base) • Only 100mm diameter
• Alarming temperature 92° • Low standby current 35.0μA nominal
• Compatible base YBO-R/4A • SSL listing afp:1118
DFJ-90D - Hochiki type ‘D’ thermal detector• Fixed temperature thermal detector • Electronic linear heat detection
• Dual LED’s for 360° viewing • Rated voltage: 24V DC (working voltage 15-30V DC)
• Low profile, only 48mm (with base) • Only 100mm diameter
• Alarming temperature 92° • Low standby current 35.0μA nominal
• Compatible base YBO-R/4A • SSL listing afp:1121
DFG-60blkJ - Hochiki sealed type ‘B’ detector• Waterproof design – rated to IP67 • Fixed temperature sealed thermal detector
• Low profile, only 45mm deep • Suitable for cool rooms, Kitchens, bathrooms etc
• No base required • Alarming temperature 58° - 88°C
• No standby current • Remote lamp ready
• SSL listing afp:661
CO
NV
ENTIO
NA
L DETEC
TOR
S
CurrENT MOdEl
dETECTOrS
CO
NV
ENTI
ON
AL
PA
NEL
S
CONvENTiONal
PaNElS
DCP-002 – Door Control / Local Alarm Panel The Incite DCP-002 is a solution for sliding fire doors and local alarm requirements.
• Self contained and simple to operate • Individual AZF alarm test, fault test, isolate & reset buttons
• 2 fully monitored AZF inputs • Individual AZF alarm, fault & isolate indicators
• Accepts AS1670 detectors • Auxiliary output to interface to other equipment
• Door holder output • Pre warning for door closers on mains failure
• Warning strobe output • Timer for door holder release operation
• Bell output monitored • Internal sounder with isolate switch
• Battery backed
CONvENTiONal PaNElS
An extensive range of Conventional panels are available, including gas control panels
Please contact us on 1300 INCITE for a panel to suit your requirements.
www.incitefire.com.au • For customer service call 1300 INCITE06 www.incitefire.com.au • For customer service call 1300 INCITE 07
slk-as – Hochiki photo optical smoke detector (previous model)• Low standby current 35.0μA nominal • Rated voltage: 24V DC (working voltage 15-30V DC)
• Compatible base YBF-RL/4AH4M or YBC-R/3A • SSL listing afp:600
DCC-a - Hochiki type ‘A’ thermal detector (previous model)• Low standby current 30.0μA nominal • Rated voltage: 24V DC (working voltage 15-30V DC)
• SSL listing afp:658 • Compatible base YBF-RL/4AH4M or YBC-R/3A
DFE-60b - Hochiki type ‘B’ thermal detector (previous model)• Low standby current 30.0μA nominal • Rated voltage: 60V DC (working voltage 0-60V DC)
• SSL listing afp:660 • Compatible base YBF-RL/4AH4M or YBC-R/3A
DCC-C - Hochiki type ‘C’ thermal detector (previous model)• Low standby current 35.0μA nominal • Rated voltage: 24V DC (working voltage 15-30V DC)
• SSL listing afp:659 • Compatible base YBF-RL/4AH4M or YBC-R/3A
DFE-90D - Hochiki type ‘D’ thermal detector (previous model)• Low standby current 30.0μA nominal • Rated voltage: 60V DC (working voltage 0-60V DC)
• SSL listing afp:663 • Compatible base YBF-RL/4AH4M or YBC-R/3A
sIH-as – Hochiki ionisation smoke detector (previous model)• Low standby current 25.0μA nominal • Rated voltage: 24V DC (working voltage 15-30V DC)
• Compatible base YBF-RL/4AH4M or YBC-R/3A • SSL listing afp:601
YBC-R/3A – Hochiki plain base (previous model)• Compatible with (previous model detectors)
~ SLK-A – Conventional photo optical ~ SIH-AS – Conventional ionisation
~ DCC-A – Conventional A type thermal ~ DFE-60B – Conventional B type thermal
~ DCC-C – Conventional C type thermal ~ DFE-90D – Conventional D type thermal
~ HF-24AMK1 – Ultra violet detector
YBF-RL/4AH4M – Hochiki conventional indicating base (previous model)• Compatible with (previous model detectors)
~ SLK-A – Conventional photo optical ~ SIH-AS – Conventional ionisation
~ DCC-A – Conventional A type thermal ~ DFE-60B – Conventional B type thermal
~ DCC-C – Conventional C type thermal ~ DFE-90D – Conventional D type thermal
~ HF-24AMK1 – Ultra violet detector
PrEviOuS MOdEl
dETECTOrS
CO
NV
ENTIO
NA
L DETEC
TOR
S
sIJ-asN – Hochiki ionisation smoke detector• Stable operation under extreme conditions • Resistant to strong vibrations & voltage fluctuation
• Low profile, only 48mm (with base) • Reliable under conditions such as high humidity
• Only 100mm diameter • Rated voltage: 24V DC (working voltage 15-30V DC)
• Nominal sensitivity – 0.4 MIC X • Compatible base YBO-R/4A
• Low standby current 25.0μA nominal • SSL listing afp:1117
vaNGuarD – Vandal proof steel cage for Hochiki detectors
DH-98-asC - Hochiki conventional duct probe• Rugged steel back box with clear cover • Compact design, only W185mm x H230mm x D50mm
• Pre mounted detector base (YBO-R/4A) • Plug in photo optical or ionisation detector
• No screens or filter to clean • Complete with 1m aluminium sampling tubes
• SSL listing afp:1569
sPC-as – Hochiki projected beam detector• Beam length of 5m – 100m • Compact design, only W86mm x H145mm x D100mm
• Microcomputer analysis of beam data • Automatic compensation for contamination of optics
• Low standby current 250.0μA nominal • Ideal for large open spaces eg: warehouse & theatres
• Sensitivity setting of 35% to 50% / span • Rated voltage: 24V DC (working voltage 15-33V DC)
• SSL listing afp:2186
HF-24amk1 – Hochiki ultraviolet flame detector• Detects flames by ultraviolet radiation • 120º detection angle
• Low profile, only 70mm (with base) • Only 100mm diameter
• Low standby current 200.0μA nominal • Rated voltage: 24V DC (working voltage 15-30V DC)
• SSL listing afp:57 • Compatible base YBO-R/3A or YBF-RL/4AH4M
TyPE E ProbE – Type E thermal probe• Seamless machined AISI 316 stainless steel • Corrosion and shock resistant
• Gold plated contacts • Factory set between 60°C to 240°C
• IP67 rating • Operating current 0.5A maximum
• Rated voltage: 24V DC • SSL listing afp:979
YBO-R/4A – Hochiki 24V conventional base• Compatible with
~ SLV-AS – Conventional photo optical ~ SIJ-AS – Conventional ionisation
~ DCD-A – Conventional A type thermal ~ DFJ-60B – Conventional B type thermal
~ DCD-C – Conventional C type thermal ~ DFJ-90D – Conventional D type thermal
CurrENT MOdEl
dETECTOrS
CO
NV
ENTI
ON
AL
DET
ECTO
RS
www.incitefire.com.au • For customer service call 1300 INCITE06 www.incitefire.com.au • For customer service call 1300 INCITE 07
slk-as – Hochiki photo optical smoke detector (previous model)• Low standby current 35.0μA nominal • Rated voltage: 24V DC (working voltage 15-30V DC)
• Compatible base YBF-RL/4AH4M or YBC-R/3A • SSL listing afp:600
DCC-a - Hochiki type ‘A’ thermal detector (previous model)• Low standby current 30.0μA nominal • Rated voltage: 24V DC (working voltage 15-30V DC)
• SSL listing afp:658 • Compatible base YBF-RL/4AH4M or YBC-R/3A
DFE-60b - Hochiki type ‘B’ thermal detector (previous model)• Low standby current 30.0μA nominal • Rated voltage: 60V DC (working voltage 0-60V DC)
• SSL listing afp:660 • Compatible base YBF-RL/4AH4M or YBC-R/3A
DCC-C - Hochiki type ‘C’ thermal detector (previous model)• Low standby current 35.0μA nominal • Rated voltage: 24V DC (working voltage 15-30V DC)
• SSL listing afp:659 • Compatible base YBF-RL/4AH4M or YBC-R/3A
DFE-90D - Hochiki type ‘D’ thermal detector (previous model)• Low standby current 30.0μA nominal • Rated voltage: 60V DC (working voltage 0-60V DC)
• SSL listing afp:663 • Compatible base YBF-RL/4AH4M or YBC-R/3A
sIH-as – Hochiki ionisation smoke detector (previous model)• Low standby current 25.0μA nominal • Rated voltage: 24V DC (working voltage 15-30V DC)
• Compatible base YBF-RL/4AH4M or YBC-R/3A • SSL listing afp:601
YBC-R/3A – Hochiki plain base (previous model)• Compatible with (previous model detectors)
~ SLK-A – Conventional photo optical ~ SIH-AS – Conventional ionisation
~ DCC-A – Conventional A type thermal ~ DFE-60B – Conventional B type thermal
~ DCC-C – Conventional C type thermal ~ DFE-90D – Conventional D type thermal
~ HF-24AMK1 – Ultra violet detector
YBF-RL/4AH4M – Hochiki conventional indicating base (previous model)• Compatible with (previous model detectors)
~ SLK-A – Conventional photo optical ~ SIH-AS – Conventional ionisation
~ DCC-A – Conventional A type thermal ~ DFE-60B – Conventional B type thermal
~ DCC-C – Conventional C type thermal ~ DFE-90D – Conventional D type thermal
~ HF-24AMK1 – Ultra violet detector
PrEviOuS MOdEl
dETECTOrS
CO
NV
ENTIO
NA
L DETEC
TOR
S
sIJ-asN – Hochiki ionisation smoke detector• Stable operation under extreme conditions • Resistant to strong vibrations & voltage fluctuation
• Low profile, only 48mm (with base) • Reliable under conditions such as high humidity
• Only 100mm diameter • Rated voltage: 24V DC (working voltage 15-30V DC)
• Nominal sensitivity – 0.4 MIC X • Compatible base YBO-R/4A
• Low standby current 25.0μA nominal • SSL listing afp:1117
vaNGuarD – Vandal proof steel cage for Hochiki detectors
DH-98-asC - Hochiki conventional duct probe• Rugged steel back box with clear cover • Compact design, only W185mm x H230mm x D50mm
• Pre mounted detector base (YBO-R/4A) • Plug in photo optical or ionisation detector
• No screens or filter to clean • Complete with 1m aluminium sampling tubes
• SSL listing afp:1569
sPC-as – Hochiki projected beam detector• Beam length of 5m – 100m • Compact design, only W86mm x H145mm x D100mm
• Microcomputer analysis of beam data • Automatic compensation for contamination of optics
• Low standby current 250.0μA nominal • Ideal for large open spaces eg: warehouse & theatres
• Sensitivity setting of 35% to 50% / span • Rated voltage: 24V DC (working voltage 15-33V DC)
• SSL listing afp:2186
HF-24amk1 – Hochiki ultraviolet flame detector• Detects flames by ultraviolet radiation • 120º detection angle
• Low profile, only 70mm (with base) • Only 100mm diameter
• Low standby current 200.0μA nominal • Rated voltage: 24V DC (working voltage 15-30V DC)
• SSL listing afp:57 • Compatible base YBO-R/3A or YBF-RL/4AH4M
TyPE E ProbE – Type E thermal probe• Seamless machined AISI 316 stainless steel • Corrosion and shock resistant
• Gold plated contacts • Factory set between 60°C to 240°C
• IP67 rating • Operating current 0.5A maximum
• Rated voltage: 24V DC • SSL listing afp:979
YBO-R/4A – Hochiki 24V conventional base• Compatible with
~ SLV-AS – Conventional photo optical ~ SIJ-AS – Conventional ionisation
~ DCD-A – Conventional A type thermal ~ DFJ-60B – Conventional B type thermal
~ DCD-C – Conventional C type thermal ~ DFJ-90D – Conventional D type thermal
CurrENT MOdEl
dETECTOrS
CO
NV
ENTI
ON
AL
DET
ECTO
RS
www.incitefire.com.au • For customer service call 1300 INCITE08 www.incitefire.com.au • For customer service call 1300 INCITE 09
AN
ALO
GU
E PA
NELS
aNalOguE PaNElS
- gTP PrOTOCOl
FireNet – Analogue/Addressable Fire Alarm Control Panel GTP Protocol• FireNet features
~ Fully compatible with Hochiki addressable detector range
~ High resolution LCD with large characters & backlighting
~ High level interface to VesdaNET
~ Site programmable using Microsoft Windows™ compatible configuration editor
~ Digifire – Windows™ compatible graphical PC interface
~ Simple to operate LCD menu with on screen prompts
~ Easy installation operation and maintenance
~ Keyswitch to enable the controls
• Programmability
~ Fully monitored inputs/outputs for ancillary equipment
~ Voltage free solid state outputs which are fully programmable
~ Utilizes Hochiki programmable loop input/output devices
~ Each I/O and/or loop device has 40 characters of text for description
~ All input devices can be allocated to a specific zone with a 40 character text description
~ Up to 999 zones allowed in system
• Digifire
~ Graphical PC interface for the FireNet
~ Full monitoring and control from the graphical user interface (GUI)
• Simple operation
~ Menu driven with clear prompts for the user
~ Operator controls through touch keys and numeric keypad
~ Fire fighters controls clearly identified
~ Full system control can be replicated at any location using multiple displays
• Capacity (subject to configuration)
~ 1922 loops of 127 Hochiki analogue/addressable devices
~ High level interface to VesdaNET
~ 1000 events logged, comprising of alarms, faults, isolates & history
• Dimensions
~ Size 2 cabinet – 660H x 500W x 170D
- Optional battery box – 225H x 500W x 170D
~ Size 3 cabinet – 974H x 560W x 225D
- Optional battery box – 487H x 560W x 225D
•SSL Listing - afp: 1373
•AS compliance
~ Complies with AS 1603.4 & AS 4428.1
aNalOguE PaNElS
- gTP PrOTOCOl
AN
ALO
GU
E P
AN
ELS
www.incitefire.com.au • For customer service call 1300 INCITE08 www.incitefire.com.au • For customer service call 1300 INCITE 09
AN
ALO
GU
E PA
NELS
aNalOguE PaNElS
- gTP PrOTOCOl
FireNet – Analogue/Addressable Fire Alarm Control Panel GTP Protocol• FireNet features
~ Fully compatible with Hochiki addressable detector range
~ High resolution LCD with large characters & backlighting
~ High level interface to VesdaNET
~ Site programmable using Microsoft Windows™ compatible configuration editor
~ Digifire – Windows™ compatible graphical PC interface
~ Simple to operate LCD menu with on screen prompts
~ Easy installation operation and maintenance
~ Keyswitch to enable the controls
• Programmability
~ Fully monitored inputs/outputs for ancillary equipment
~ Voltage free solid state outputs which are fully programmable
~ Utilizes Hochiki programmable loop input/output devices
~ Each I/O and/or loop device has 40 characters of text for description
~ All input devices can be allocated to a specific zone with a 40 character text description
~ Up to 999 zones allowed in system
• Digifire
~ Graphical PC interface for the FireNet
~ Full monitoring and control from the graphical user interface (GUI)
• Simple operation
~ Menu driven with clear prompts for the user
~ Operator controls through touch keys and numeric keypad
~ Fire fighters controls clearly identified
~ Full system control can be replicated at any location using multiple displays
• Capacity (subject to configuration)
~ 1922 loops of 127 Hochiki analogue/addressable devices
~ High level interface to VesdaNET
~ 1000 events logged, comprising of alarms, faults, isolates & history
• Dimensions
~ Size 2 cabinet – 660H x 500W x 170D
- Optional battery box – 225H x 500W x 170D
~ Size 3 cabinet – 974H x 560W x 225D
- Optional battery box – 487H x 560W x 225D
•SSL Listing - afp: 1373
•AS compliance
~ Complies with AS 1603.4 & AS 4428.1
aNalOguE PaNElS
- gTP PrOTOCOl
AN
ALO
GU
E P
AN
ELS
www.incitefire.com.au • For customer service call 1300 INCITE10 www.incitefire.com.au • For customer service call 1300 INCITE 11
aCa-E – Hochiki analogue multi-sensor• Address stored in non volatile memory • Addressable using handheld programmer (TCH-B100)
• Dual LED’s for 360° viewing • Combined photo optical & thermal elements
• Low profile, only 52mm (with base) • Only 100mm diameter
• Sensitivity: variable • Low standby current 450.0μA typical
• Compatible base YBN-R/2NA, YBO-R/SCI • SSL listing afp:1590
vaNGuarD – Vandal proof steel cage for Hochiki detectors
DH-98-asa – Hochiki analogue duct probe• Rugged steel back box with clear cover • Pre mounted detector base (YBN-R/2NA)
• Plug in photo optical or ionisation detector • No screens or filter to clean
• Complete with 1m aluminium sampling tubes • SSL listing afp:1569
• Compact design, only W185mm x H230mm x D50mm
YBN-R/2NA – Hochiki analogue base• Compatible with
~ ALG-AS – Analogue photo optical smoke ~ ATG-AS – Analogue thermal
~ AIE-AS – Analogue ionisation ~ ACA-E – Analogue multi-smoke/thermal
~ ACB-AS – Analogue multi-thermal
YBN-R/3 BLKANA – Hochiki black analogue base
YBO-R/SCI – Hochiki analogue short circuit isolator base• Compatible with
~ ALG-AS – Analogue photo optical smoke ~ ATG-AS – Analogue thermal
~ AIE-AS – Analogue ionisation ~ ACA-E – Analogue multi-smoke/thermal
~ ACB-AS – Analogue multi-thermal
AN
ALO
GU
E DEV
ICES
dETECTOrS
- gTP PrOTOCOl
alG-as - Hochiki analogue photo optical smoke detector• Very fast alarm response • Addressable using handheld programmer (TCH-B100)
• Address stored in non volatile memory • Dual LED’s for 360° viewing
• Low profile, only 46mm (with base) • Only 100mm diameter
• Low standby current 390.0μA typical • Sensitivity: variable
• Compatible base YBN-R/2NA, YBO-R/SCI • SSL listing afp:1089
alG-slr-blk CovEr – Black cover for ALG-AS
aTG-as - Hochiki analogue thermal detector• Rapid response to change in temperature • Addressable using handheld programmer (TCH-B100)
• Address stored in non volatile memory • Dual LED’s for 360° viewing
• Low profile, only 46mm (with base) • Only 100mm diameter
• Sensitivity: variable • Low standby current 350.0μA typical
• Compatible base YBN-R/2NA, YBO-R/SCI • SSL listing afp:1088
aCb-as - Hochiki multi-thermal detector• Address stored in non volatile memory • Addressable using handheld programmer (TCH-B100)
• Dual LED’s for 360° viewing • Combination rate of rise & fixed temperature
• Low profile, only 46mm (with base) • Only 100mm diameter
• Sensitivity: variable • Low standby current 350.0μA typical
• Compatible base YBN-R/2NA, YBO-R/SCI • SSL listing afp: 1817
aCb-asw - Hochiki multi-thermal detector (weatherproof)• IP67 rating • Addressable using handheld programmer (TCH-B100)
• Dual LED’s for 360° viewing • Combination rate of rise & fixed temperature
• Low profile, only 46mm (with base) • Only 100mm diameter
• Sensitivity: variable • Low standby current 350.0μA typical
• Fixing base supplied • SSL listing afp: 1817
aIE-as – Hochiki analogue ionisation detector• Dual chamber for fast alarm response • Addressable using handheld programmer (TCH-B100)
• Address stored in non volatile memory • Dual LED’s for 360° viewing
• Low profile, only 52mm (with base) • Only 100mm diameter
• Sensitivity: variable • Low standby current 350.0μA typical
• Compatible base YBN-R/2NA, YBO-R/SCI • SSL listing afp:1087
AN
ALO
GU
E D
EVIC
ES
dETECTOrS
- gTP PrOTOCOl
www.incitefire.com.au • For customer service call 1300 INCITE10 www.incitefire.com.au • For customer service call 1300 INCITE 11
aCa-E – Hochiki analogue multi-sensor• Address stored in non volatile memory • Addressable using handheld programmer (TCH-B100)
• Dual LED’s for 360° viewing • Combined photo optical & thermal elements
• Low profile, only 52mm (with base) • Only 100mm diameter
• Sensitivity: variable • Low standby current 450.0μA typical
• Compatible base YBN-R/2NA, YBO-R/SCI • SSL listing afp:1590
vaNGuarD – Vandal proof steel cage for Hochiki detectors
DH-98-asa – Hochiki analogue duct probe• Rugged steel back box with clear cover • Pre mounted detector base (YBN-R/2NA)
• Plug in photo optical or ionisation detector • No screens or filter to clean
• Complete with 1m aluminium sampling tubes • SSL listing afp:1569
• Compact design, only W185mm x H230mm x D50mm
YBN-R/2NA – Hochiki analogue base• Compatible with
~ ALG-AS – Analogue photo optical smoke ~ ATG-AS – Analogue thermal
~ AIE-AS – Analogue ionisation ~ ACA-E – Analogue multi-smoke/thermal
~ ACB-AS – Analogue multi-thermal
YBN-R/3 BLKANA – Hochiki black analogue base
YBO-R/SCI – Hochiki analogue short circuit isolator base• Compatible with
~ ALG-AS – Analogue photo optical smoke ~ ATG-AS – Analogue thermal
~ AIE-AS – Analogue ionisation ~ ACA-E – Analogue multi-smoke/thermal
~ ACB-AS – Analogue multi-thermal
AN
ALO
GU
E DEV
ICES
dETECTOrS
- gTP PrOTOCOl
alG-as - Hochiki analogue photo optical smoke detector• Very fast alarm response • Addressable using handheld programmer (TCH-B100)
• Address stored in non volatile memory • Dual LED’s for 360° viewing
• Low profile, only 46mm (with base) • Only 100mm diameter
• Low standby current 390.0μA typical • Sensitivity: variable
• Compatible base YBN-R/2NA, YBO-R/SCI • SSL listing afp:1089
alG-slr-blk CovEr – Black cover for ALG-AS
aTG-as - Hochiki analogue thermal detector• Rapid response to change in temperature • Addressable using handheld programmer (TCH-B100)
• Address stored in non volatile memory • Dual LED’s for 360° viewing
• Low profile, only 46mm (with base) • Only 100mm diameter
• Sensitivity: variable • Low standby current 350.0μA typical
• Compatible base YBN-R/2NA, YBO-R/SCI • SSL listing afp:1088
aCb-as - Hochiki multi-thermal detector• Address stored in non volatile memory • Addressable using handheld programmer (TCH-B100)
• Dual LED’s for 360° viewing • Combination rate of rise & fixed temperature
• Low profile, only 46mm (with base) • Only 100mm diameter
• Sensitivity: variable • Low standby current 350.0μA typical
• Compatible base YBN-R/2NA, YBO-R/SCI • SSL listing afp: 1817
aCb-asw - Hochiki multi-thermal detector (weatherproof)• IP67 rating • Addressable using handheld programmer (TCH-B100)
• Dual LED’s for 360° viewing • Combination rate of rise & fixed temperature
• Low profile, only 46mm (with base) • Only 100mm diameter
• Sensitivity: variable • Low standby current 350.0μA typical
• Fixing base supplied • SSL listing afp: 1817
aIE-as – Hochiki analogue ionisation detector• Dual chamber for fast alarm response • Addressable using handheld programmer (TCH-B100)
• Address stored in non volatile memory • Dual LED’s for 360° viewing
• Low profile, only 52mm (with base) • Only 100mm diameter
• Sensitivity: variable • Low standby current 350.0μA typical
• Compatible base YBN-R/2NA, YBO-R/SCI • SSL listing afp:1087
AN
ALO
GU
E D
EVIC
ES
dETECTOrS
- gTP PrOTOCOl
www.incitefire.com.au • For customer service call 1300 INCITE12 www.incitefire.com.au • For customer service call 1300 INCITE 13
TCH-b100 – Hochiki handheld programmer
MiMiC PaNElS
rEPEaTEr – FireNet repeater panel•Full size backlit LCD display •Full Control or scroll only
•Surface mount with silver finish fascia •Flush mount with stainless steel fascia
mImIC – FireNet mimic panel•2 line LCD display •Scroll only
addrESSablE bEaCON & SOuNdEr baSE
CHq-ab - Hochiki addressable beacon
CHq-bs - Hochiki addressable loop powered sounder base
NoTEs
AN
ALO
GU
E DEV
ICES
PrOgraMMEr
MiMiCS
STrObE
SOuNdEr
AN
ALO
GU
E D
EVIC
ES
YCA-RL/3H2M – Hochiki addressable base• Compatible with
~ SLV-AS – Conventional photo optical ~ SIJ-AS – Conventional ionisation
~ DCD-A – Conventional A type thermal ~ DFJ-60B – Conventional B type thermal
~ DCD-C – Conventional C type thermal ~ DFJ-90D – Conventional D type thermal
YCA-RL/5H2M – Hochiki addressable master base• 1 conventional zone input - up to 5 conventional detectors using YBO-R/4A bases
• Compatible with
~ SLV-AS – Conventional photo optical ~ SIJ-AS – Conventional ionisation
~ DCD-A – Conventional A type thermal ~ DFJ-60B – Conventional B type thermal
~ DCD-C – Conventional C type thermal ~ DFG-60BLKJ – Conventional B type sealed thermal
~ DFJ-90D – Conventional D type thermal (Slave only)
NoTEs
dETECTOrS
- gTP PrOTOCOl
www.incitefire.com.au • For customer service call 1300 INCITE12 www.incitefire.com.au • For customer service call 1300 INCITE 13
TCH-b100 – Hochiki handheld programmer
MiMiC PaNElS
rEPEaTEr – FireNet repeater panel•Full size backlit LCD display •Full Control or scroll only
•Surface mount with silver finish fascia •Flush mount with stainless steel fascia
mImIC – FireNet mimic panel•2 line LCD display •Scroll only
addrESSablE bEaCON & SOuNdEr baSE
CHq-ab - Hochiki addressable beacon
CHq-bs - Hochiki addressable loop powered sounder base
NoTEs
AN
ALO
GU
E DEV
ICES
PrOgraMMEr
MiMiCS
STrObE
SOuNdEr
AN
ALO
GU
E D
EVIC
ES
YCA-RL/3H2M – Hochiki addressable base• Compatible with
~ SLV-AS – Conventional photo optical ~ SIJ-AS – Conventional ionisation
~ DCD-A – Conventional A type thermal ~ DFJ-60B – Conventional B type thermal
~ DCD-C – Conventional C type thermal ~ DFJ-90D – Conventional D type thermal
YCA-RL/5H2M – Hochiki addressable master base• 1 conventional zone input - up to 5 conventional detectors using YBO-R/4A bases
• Compatible with
~ SLV-AS – Conventional photo optical ~ SIJ-AS – Conventional ionisation
~ DCD-A – Conventional A type thermal ~ DFJ-60B – Conventional B type thermal
~ DCD-C – Conventional C type thermal ~ DFG-60BLKJ – Conventional B type sealed thermal
~ DFJ-90D – Conventional D type thermal (Slave only)
NoTEs
dETECTOrS
- gTP PrOTOCOl
www.incitefire.com.au • For customer service call 1300 INCITE14 www.incitefire.com.au • For customer service call 1300 INCITE 15
CHq-CP – Clean contact input module •Loop powered •Non monitored general input module
•Addressed using DIP switches •Low standby current 230.0μA typical
mCP-E-aDD – Hochiki addressable manual call point• Fast Response • Status LED
• Addressed using DIP switches • Complete with back box
mCP-E-aDD-wP - Hochiki addressable manual call point (weatherproof)
• Addressed using DIP switches • Complete with back box
• IP67 rating
squasNImICro – Low current sounder• Ultra low 3mA current consumption • Powered from detector remote indicator output
• Colour matched to Hochiki detectors
ShOrT CirCuiT iSOlaTOrS – gTP PrOTOCOl
CHq-sCI-s – Loop short circuit isolator• Position at any point on loop • Short circuit isolator for signal transmission line
• LED indication when S/C detected • Quick & reliable detection of short circuit
YBO-R/SCI – Hochiki analogue short circuit isolator base• Compatible with
~ ALG-AS – Analogue photo optical smoke ~ ATG-AS – Analogue thermal
~ AIE-AS – Analogue ionisation ~ ACA-E – Analogue multi-smoke/thermal
~ ACB-AS – Analogue multi-thermal
FiEld dEviCES
– gTP PrOTOCOl
AN
ALO
GU
E DEV
ICES
CHq-b – Output module for bell / sounder / strobe• 2 monitored and fused outputs • Requires 24V supply
• 1 monitored input • Addressed using DIP switches
• Typical uses: • Supervised for O/C & S/C conditions
~ Bells, Sounders, Strobes
CHQ-Z – Conventional loops controller• 2 conventional zones • Zones O/C and S/C monitored
• Requires 24V supply • 20 Hochiki conventional detectors per zone
• Addressed using DIP switches • Auxiliary output for remote fire indication
CHq-s – Dual input module • Dual non monitored inputs • Individual selection of N/O or N/C contacts
• Loop powered • Addressed using DIP switches
CHQ-MZ – Mini zone module• Loop powered • 1 conventional zone input – up to 6 conv. detectors
• Addressed using DIP switches • Zone O/C and S/C monitored
• Remote fire indication output • Supervised external power input
CHq-r – Relay output module• 1 monitored input • 2 independent volt free relay output (N/O & N/C)
• Loop powered • Addressed using DIP switches
• Typical uses:
~ Fan controls, Fire Trips, Flow switch test solenoids
CHq-sCI-s – Loop short circuit isolator• Position at any point on loop • Short circuit isolator for signal transmission line
• LED indication when S/C detected • Quick & reliable detection of short circuit
FiEld dEviCES
– gTP PrOTOCOl
AN
ALO
GU
E D
EVIC
ES
www.incitefire.com.au • For customer service call 1300 INCITE14 www.incitefire.com.au • For customer service call 1300 INCITE 15
CHq-CP – Clean contact input module •Loop powered •Non monitored general input module
•Addressed using DIP switches •Low standby current 230.0μA typical
mCP-E-aDD – Hochiki addressable manual call point• Fast Response • Status LED
• Addressed using DIP switches • Complete with back box
mCP-E-aDD-wP - Hochiki addressable manual call point (weatherproof)
• Addressed using DIP switches • Complete with back box
• IP67 rating
squasNImICro – Low current sounder• Ultra low 3mA current consumption • Powered from detector remote indicator output
• Colour matched to Hochiki detectors
ShOrT CirCuiT iSOlaTOrS – gTP PrOTOCOl
CHq-sCI-s – Loop short circuit isolator• Position at any point on loop • Short circuit isolator for signal transmission line
• LED indication when S/C detected • Quick & reliable detection of short circuit
YBO-R/SCI – Hochiki analogue short circuit isolator base• Compatible with
~ ALG-AS – Analogue photo optical smoke ~ ATG-AS – Analogue thermal
~ AIE-AS – Analogue ionisation ~ ACA-E – Analogue multi-smoke/thermal
~ ACB-AS – Analogue multi-thermal
FiEld dEviCES
– gTP PrOTOCOl
AN
ALO
GU
E DEV
ICES
CHq-b – Output module for bell / sounder / strobe• 2 monitored and fused outputs • Requires 24V supply
• 1 monitored input • Addressed using DIP switches
• Typical uses: • Supervised for O/C & S/C conditions
~ Bells, Sounders, Strobes
CHQ-Z – Conventional loops controller• 2 conventional zones • Zones O/C and S/C monitored
• Requires 24V supply • 20 Hochiki conventional detectors per zone
• Addressed using DIP switches • Auxiliary output for remote fire indication
CHq-s – Dual input module • Dual non monitored inputs • Individual selection of N/O or N/C contacts
• Loop powered • Addressed using DIP switches
CHQ-MZ – Mini zone module• Loop powered • 1 conventional zone input – up to 6 conv. detectors
• Addressed using DIP switches • Zone O/C and S/C monitored
• Remote fire indication output • Supervised external power input
CHq-r – Relay output module• 1 monitored input • 2 independent volt free relay output (N/O & N/C)
• Loop powered • Addressed using DIP switches
• Typical uses:
~ Fan controls, Fire Trips, Flow switch test solenoids
CHq-sCI-s – Loop short circuit isolator• Position at any point on loop • Short circuit isolator for signal transmission line
• LED indication when S/C detected • Quick & reliable detection of short circuit
FiEld dEviCES
– gTP PrOTOCOl
AN
ALO
GU
E D
EVIC
ES
www.incitefire.com.au • For customer service call 1300 INCITE16 www.incitefire.com.au • For customer service call 1300 INCITE 17
AN
ALO
GU
E DEV
ICES
NoTEsalb-E - Hochiki analogue photo optical smoke detector (HRE protocol)*• Low standby current 0.35mA nominal • Compatible base YBF-RL/2NBF
• SSL listing afp:597 • Rated voltage: 24V DC (working voltage 18-27V DC)
aTa-E - Hochiki analogue thermal detector (HRE protocol)*• Low standby current 7mA nominal • Compatible base YBF-RL/2NBF
• SSL listing afp:59 • Rated voltage: 24V DC (working voltage 18-27V DC)
aIa-E – Hochiki analogue ionisation smoke detector (HRE protocol)*• Low standby current 7mA nominal • Compatible base YBF-RL/2NBF
• SSL listing afp:686 • Rated voltage: 24V DC (working voltage 18-27V DC)
YBF-RL/2NBF – Hochiki analogue base (HRE protocol)*• Compatible with
~ ATA-E – Analogue thermal (HRE protocol) ~ ALB-E – Analogue photo optical (HRE protocol)
~ AIA-E – Analogue ionisation (HRE protocol)
amu-b2m – Hochiki addressable base (HRE protocol)*•Compatible with (previous model conventional detectors)
~ SLK-A – Conventional photo optical ~ SIH-AS – Conventional ionisation
~ DCC-A – Conventional A type thermal ~ DFE-60B – Conventional B type thermal
~ DCC-C – Conventional C type thermal ~ DFE-90D – Conventional D type thermal
amu-mbm – Hochiki addressable master base (HRE protocol)*• Compatible with
~ SLK-A – Conventional photo optical ~ SIH-AS – Conventional ionisation
~ DCC-A – Conventional A type thermal ~ DFE-60B – Conventional B type thermal
~ DCC-C – Conventional C type thermal ~ DFE-90D – Conventional D type thermal
YBF-RL/3JM – Hochiki slave base (HRE protocol)*• Compatible with
~ SLK-A – Conventional photo optical ~ SIH-AS – Conventional ionisation
~ DCC-A – Conventional A type thermal ~ DFE-60B – Conventional B type thermal
~ DCC-C – Conventional C type thermal ~ DFE-90D – Conventional D type thermal
FiEld dEviCESamu-C2 – Output module for bell (HRE protocol)*amu-a2a – Input module for monitoring contacts (HRE protocol)*
AN
ALO
GU
E D
EVIC
ES
*HRE Protocol Devices & Detectors are NOW compatible with FireNet panel.
*HRE Protocol Devices & Detectors are NOW compatible with FireNet panel.
PrEviOuS dETECTOrS
- hrE PrOTOCOl
FiEld dEviCES
C O M P a T i b l E
www.incitefire.com.au • For customer service call 1300 INCITE16 www.incitefire.com.au • For customer service call 1300 INCITE 17
AN
ALO
GU
E DEV
ICES
NoTEsalb-E - Hochiki analogue photo optical smoke detector (HRE protocol)*• Low standby current 0.35mA nominal • Compatible base YBF-RL/2NBF
• SSL listing afp:597 • Rated voltage: 24V DC (working voltage 18-27V DC)
aTa-E - Hochiki analogue thermal detector (HRE protocol)*• Low standby current 7mA nominal • Compatible base YBF-RL/2NBF
• SSL listing afp:59 • Rated voltage: 24V DC (working voltage 18-27V DC)
aIa-E – Hochiki analogue ionisation smoke detector (HRE protocol)*• Low standby current 7mA nominal • Compatible base YBF-RL/2NBF
• SSL listing afp:686 • Rated voltage: 24V DC (working voltage 18-27V DC)
YBF-RL/2NBF – Hochiki analogue base (HRE protocol)*• Compatible with
~ ATA-E – Analogue thermal (HRE protocol) ~ ALB-E – Analogue photo optical (HRE protocol)
~ AIA-E – Analogue ionisation (HRE protocol)
amu-b2m – Hochiki addressable base (HRE protocol)*•Compatible with (previous model conventional detectors)
~ SLK-A – Conventional photo optical ~ SIH-AS – Conventional ionisation
~ DCC-A – Conventional A type thermal ~ DFE-60B – Conventional B type thermal
~ DCC-C – Conventional C type thermal ~ DFE-90D – Conventional D type thermal
amu-mbm – Hochiki addressable master base (HRE protocol)*• Compatible with
~ SLK-A – Conventional photo optical ~ SIH-AS – Conventional ionisation
~ DCC-A – Conventional A type thermal ~ DFE-60B – Conventional B type thermal
~ DCC-C – Conventional C type thermal ~ DFE-90D – Conventional D type thermal
YBF-RL/3JM – Hochiki slave base (HRE protocol)*• Compatible with
~ SLK-A – Conventional photo optical ~ SIH-AS – Conventional ionisation
~ DCC-A – Conventional A type thermal ~ DFE-60B – Conventional B type thermal
~ DCC-C – Conventional C type thermal ~ DFE-90D – Conventional D type thermal
FiEld dEviCESamu-C2 – Output module for bell (HRE protocol)*amu-a2a – Input module for monitoring contacts (HRE protocol)*
AN
ALO
GU
E D
EVIC
ES
*HRE Protocol Devices & Detectors are NOW compatible with FireNet panel.
*HRE Protocol Devices & Detectors are NOW compatible with FireNet panel.
PrEviOuS dETECTOrS
- hrE PrOTOCOl
FiEld dEviCES
C O M P a T i b l E
www.incitefire.com.au • For customer service call 1300 INCITE18 www.incitefire.com.au • For customer service call 1300 INCITE 19
LaserSCANNER• Individual pipe detection • Laser based absolute smoke detection
• Adaptive scan threshold • Wide sensitivity range
• Up to 2,000m2 (across 4 sectors) * • VESDAnet communication
• 4 alarm levels per inlet pipe • High efficiency aspirator
• Dual stage air filter • 7 or 12 programmable relays option
• Auto learn & referencing • Event log
• Various configurations available • Recessed mounting kit available (VSP-011)
• SSL listing afp:1083
*Dependent on exterior airflow & environmental conditions
vls-200 – Blank, blank, blank, 7 relays fitted
vls-300 – Blank, blank, blank, 12 relays fitted
vls-204 – Blank, blank, display, 7 relays fitted
vls-304 – Blank, blank, display, 12 relays fitted
vls-210 – Blank, programmer, blank, 7 relays fitted
vls-310 – Blank, programmer, blank, 12 relays fitted
vls-214 – Blank, display, programmer, 7 relays fitted
vls-314 – Blank, display, programmer, 12 relays fitted
vls-600 – Blank, blank, blank with Fire 1 & OK LEDs, 7 relays fitted
vls-700 – Blank, blank, blank with Fire 1 & OK LEDs, 12 relays fitted
VESDA Ex d – Explosion proof VLC-505• Ex d IIB T6 certified • Ex d cert. Flame arrestors on inlet & exhaust
• Single pipe inlet • Laser based absolute smoke detection
• Up to 800m2 * • 3 Relays = Alert/Fault, Pre-alarm & Fire
• Five status LED’s • Optional remote display and relays
• Wide sensitivity range • Dual stage dust filter
• Auto learn & referencing • Air flow monitoring
• VesdaNET communication • Simple mounting design
• Hinged door
*Dependent on exterior airflow & environmental conditions
vlx-100 – VLC-505 in explosion proof housing with flame arrestors
vESda aSPiraTEd
SMOkE dETECTOrS
VESD
A
LaserFOCUS• Ultrasonic airflow sensing • Out of the box installation & commissioning
• Auto learn smoke & flow • Laser-based absolute smoke detection
• Event log up to 18000 events • Networkable with VIC-010 interface card
• VLF-250 up to 250m2* • 2 alarm and 1 programmable fault relays
• VLF-500 up to 500m2* • Offline/online configuration capability
• Programmable alarm thresholds • Multiple event logging in separate logs
• SSL listing afp:1770
vlF-250 – Up to 250m2 coverage* vIC-010 – LaserFOCUS network cardvlF-500 – Up to 500m2 coverage* vIC-020 – LaserFOCUS relay card*Dependent on exterior airflow & environmental conditions
LaserCOMPACT• Single pipe inlet • Optional remote display & relays (VLC-505 only)
• Up to 800m2 * • Laser based absolute smoke detection
• Five status LED’s • 3 Relays = Alert/Fault, Pre-alarm & Fire
• Wide sensitivity range • VesdaNET communication (VLC-505 only)
• Dual stage dust filter • Referencing (VLC-505 only)
• Air flow monitoring • SSL listing afp:1083
• Auto learn
*Dependent on exterior airflow & environmental conditions
vlC-500 – Relays onlyvlC-505 – VesdaNET
LaserPLUS• 4 configurable alarm levels • Laser based absolute smoke detection
• 4 inlet pipes • Up to 2,000m2 *
• High efficiency aspirator • Airflow supervisor per inlet pipe
• Dual stage air filter • 7 programmable relays
• VESDAnet communication • Auto learn & referencing
• Event log • Recessed mounting kit available (VSP-011)
• Available in various configurations • SSL listing afp:1083
*Dependent on exterior airflow & environmental conditions
vlP-000 – Blank, blank, blank plates fittedvlP-002 – Blank, blank, display fittedvlP-012 – Blank, display, programmer fittedvlP-400 – Blank, blank, blank with Fire 1 & OK LEDs fitted
vESda aSPiraTEd
SMOkE dETECTOrS
VES
DA
www.incitefire.com.au • For customer service call 1300 INCITE18 www.incitefire.com.au • For customer service call 1300 INCITE 19
LaserSCANNER• Individual pipe detection • Laser based absolute smoke detection
• Adaptive scan threshold • Wide sensitivity range
• Up to 2,000m2 (across 4 sectors) * • VESDAnet communication
• 4 alarm levels per inlet pipe • High efficiency aspirator
• Dual stage air filter • 7 or 12 programmable relays option
• Auto learn & referencing • Event log
• Various configurations available • Recessed mounting kit available (VSP-011)
• SSL listing afp:1083
*Dependent on exterior airflow & environmental conditions
vls-200 – Blank, blank, blank, 7 relays fitted
vls-300 – Blank, blank, blank, 12 relays fitted
vls-204 – Blank, blank, display, 7 relays fitted
vls-304 – Blank, blank, display, 12 relays fitted
vls-210 – Blank, programmer, blank, 7 relays fitted
vls-310 – Blank, programmer, blank, 12 relays fitted
vls-214 – Blank, display, programmer, 7 relays fitted
vls-314 – Blank, display, programmer, 12 relays fitted
vls-600 – Blank, blank, blank with Fire 1 & OK LEDs, 7 relays fitted
vls-700 – Blank, blank, blank with Fire 1 & OK LEDs, 12 relays fitted
VESDA Ex d – Explosion proof VLC-505• Ex d IIB T6 certified • Ex d cert. Flame arrestors on inlet & exhaust
• Single pipe inlet • Laser based absolute smoke detection
• Up to 800m2 * • 3 Relays = Alert/Fault, Pre-alarm & Fire
• Five status LED’s • Optional remote display and relays
• Wide sensitivity range • Dual stage dust filter
• Auto learn & referencing • Air flow monitoring
• VesdaNET communication • Simple mounting design
• Hinged door
*Dependent on exterior airflow & environmental conditions
vlx-100 – VLC-505 in explosion proof housing with flame arrestors
vESda aSPiraTEd
SMOkE dETECTOrS
VESD
A
LaserFOCUS• Ultrasonic airflow sensing • Out of the box installation & commissioning
• Auto learn smoke & flow • Laser-based absolute smoke detection
• Event log up to 18000 events • Networkable with VIC-010 interface card
• VLF-250 up to 250m2* • 2 alarm and 1 programmable fault relays
• VLF-500 up to 500m2* • Offline/online configuration capability
• Programmable alarm thresholds • Multiple event logging in separate logs
• SSL listing afp:1770
vlF-250 – Up to 250m2 coverage* vIC-010 – LaserFOCUS network cardvlF-500 – Up to 500m2 coverage* vIC-020 – LaserFOCUS relay card*Dependent on exterior airflow & environmental conditions
LaserCOMPACT• Single pipe inlet • Optional remote display & relays (VLC-505 only)
• Up to 800m2 * • Laser based absolute smoke detection
• Five status LED’s • 3 Relays = Alert/Fault, Pre-alarm & Fire
• Wide sensitivity range • VesdaNET communication (VLC-505 only)
• Dual stage dust filter • Referencing (VLC-505 only)
• Air flow monitoring • SSL listing afp:1083
• Auto learn
*Dependent on exterior airflow & environmental conditions
vlC-500 – Relays onlyvlC-505 – VesdaNET
LaserPLUS• 4 configurable alarm levels • Laser based absolute smoke detection
• 4 inlet pipes • Up to 2,000m2 *
• High efficiency aspirator • Airflow supervisor per inlet pipe
• Dual stage air filter • 7 programmable relays
• VESDAnet communication • Auto learn & referencing
• Event log • Recessed mounting kit available (VSP-011)
• Available in various configurations • SSL listing afp:1083
*Dependent on exterior airflow & environmental conditions
vlP-000 – Blank, blank, blank plates fittedvlP-002 – Blank, blank, display fittedvlP-012 – Blank, display, programmer fittedvlP-400 – Blank, blank, blank with Fire 1 & OK LEDs fitted
vESda aSPiraTEd
SMOkE dETECTOrS
VES
DA
www.incitefire.com.au • For customer service call 1300 INCITE20 www.incitefire.com.au • For customer service call 1300 INCITE 21
VESD
A
vsP-005 - Filter assembly (VLF, VLC, VLP & VLS)
E700-Fmk-2 - Filter for Vesda Mk2 system
E700-Fmk-4 - Filter for E70D (scanner & Mini) & E700
E700-FIlassy - In line pre filter for any Vesda detector
E700-FIlFoam - Foam filter only to suit E700-FMK-4 & E700-FILASSY
FirENET hli
vHx-FIrENET - FireNet/VESDA high level interface
Please contact us on 1300 INCITE for more information on the FireNet HLI
vESda SOFTwarE & aCCESSOriES
vHH-100 - Hand held programmer & cable
vHx-0200 - VesdaNET PC link HLI
Please contact us on 1300 INCITE for information on Vesda configuration and
management software.
POwEr SuPPliES
A range of Stand alone power supplies and batteries are available. Please contact
us on 1300 INCITE for a power supply to suit your Vesda requirements.
FilTErS
POwEr SuPPliES
SOFTwarE
LaserFOCUS Remote UnitsvrT-v00 - Remote box fitted with VLF display and 7 relays
LaserCOMPACT Remote UnitsvrT-J00 - Remote box fitted with VLC-505 display and 7 relaysvrT-k00 - Remote box fitted with VLC-505 display and no relays
LaserPLUS Remote UnitsvrT-200 - Remote box fitted with VLP display and 7 relaysvrT-500 - Remote box fitted with blank plate DRP & 7 relay cardvrT-600 - Remote box fitted with VLP display and no relaysvrT-F00 - Remote box fitted with blank plate DRP &12 relay card
LaserSCANNER Remote UnitsvrT-400 - Remote box fitted with VLS display and 7 relaysvrT-700 - Remote box fitted with VLS display and no relaysvrT-800 - Remote box fitted with VLS display and 12 relaysvrT-900 - Remote box fitted with blank plate DRP & 12 relay cardvrT-E00 - Remote box fitted with blank plate DRP & 7 relay card
General Remote UnitsvrT-100 - Remote box fitted with programmervrT-300 - Remote box fitted with VesdaNET socketvrT-a10 - Remote box fitted with analogue output module
vESda 19” raCkS
vsr-xxxx – Available in various configurations
Please contact us on 1300 INCITE for configuration to suit your application.
rEMOTE uNiTS
19” raCkS
VES
DA
www.incitefire.com.au • For customer service call 1300 INCITE20 www.incitefire.com.au • For customer service call 1300 INCITE 21
VESD
A
vsP-005 - Filter assembly (VLF, VLC, VLP & VLS)
E700-Fmk-2 - Filter for Vesda Mk2 system
E700-Fmk-4 - Filter for E70D (scanner & Mini) & E700
E700-FIlassy - In line pre filter for any Vesda detector
E700-FIlFoam - Foam filter only to suit E700-FMK-4 & E700-FILASSY
FirENET hli
vHx-FIrENET - FireNet/VESDA high level interface
Please contact us on 1300 INCITE for more information on the FireNet HLI
vESda SOFTwarE & aCCESSOriES
vHH-100 - Hand held programmer & cable
vHx-0200 - VesdaNET PC link HLI
Please contact us on 1300 INCITE for information on Vesda configuration and
management software.
POwEr SuPPliES
A range of Stand alone power supplies and batteries are available. Please contact
us on 1300 INCITE for a power supply to suit your Vesda requirements.
FilTErS
POwEr SuPPliES
SOFTwarE
LaserFOCUS Remote UnitsvrT-v00 - Remote box fitted with VLF display and 7 relays
LaserCOMPACT Remote UnitsvrT-J00 - Remote box fitted with VLC-505 display and 7 relaysvrT-k00 - Remote box fitted with VLC-505 display and no relays
LaserPLUS Remote UnitsvrT-200 - Remote box fitted with VLP display and 7 relaysvrT-500 - Remote box fitted with blank plate DRP & 7 relay cardvrT-600 - Remote box fitted with VLP display and no relaysvrT-F00 - Remote box fitted with blank plate DRP &12 relay card
LaserSCANNER Remote UnitsvrT-400 - Remote box fitted with VLS display and 7 relaysvrT-700 - Remote box fitted with VLS display and no relaysvrT-800 - Remote box fitted with VLS display and 12 relaysvrT-900 - Remote box fitted with blank plate DRP & 12 relay cardvrT-E00 - Remote box fitted with blank plate DRP & 7 relay card
General Remote UnitsvrT-100 - Remote box fitted with programmervrT-300 - Remote box fitted with VesdaNET socketvrT-a10 - Remote box fitted with analogue output module
vESda 19” raCkS
vsr-xxxx – Available in various configurations
Please contact us on 1300 INCITE for configuration to suit your application.
rEMOTE uNiTS
19” raCkS
VES
DA
www.incitefire.com.au • For customer service call 1300 INCITE22 www.incitefire.com.au • For customer service call 1300 INCITE 23
vESda rEPairS
We can arrange repairs for all current models of Vesda detectors. Please contact us
on 1300 INCITE for more information.
vESda TraiNiNg Please contact us on 1300 INCITE for Vesda Accreditation training courses.
NoTEs
VESD
A
rEPairS
TraiNiNg
vsP-000 - Blank plate non EMC with VESDA logovsP-001 - Programmer modulevsP-002 - Display module for LaserPLUSvsP-003 - VesdaNET socketvsP-004 - Display Module for LaserSCANNERvsP-006 - Detector chassis & manifold assembly for LaserPLUSvsP-007 - Remote termination card no relaysvsP-008 - Remote termination card with 7 relaysvsP-009 - Detector chassis & manifold assembly for LaserSCANNERvsP-011 - Recess mounting kit (VLP & VLS)vsP-012 - Remote recess mounting kitvsP-013 - Cover assembly with EMC shields (VLP & VLS)vsP-014 - Head termination card with 7 relaysvsP-015 - Detector aspirator assembly (VLP & VLS)vsP-016 - Head termination card with 12 relays (VLS only)vsP-018 - Filter switch assembly (VLP & VLS)vsP-019 - Filter cover (VLP & VLS)vsP-020 - Screw covers (2)vsP-021 - Pipe adaptors 25mm to 27mm (4)vsP-022 - Mounting box detectorvsP-023 - Front cover (VLC-505)vsP-024 - Front cover (VLC-500)vsP-100 - Blank plate non-EMC, Fire 1 & OK LEDsvsP-102 - Remote relay processor without displayvsP-103 - Remote relay processor without display (VLS)vsP-200 - Blank plate EMC painted, without VESDA logovsP-208 - Remote termination card with 12 relays (VLS only)vsP-300 - Blank plate non EMC without VESDA logovsP-501 - VLC aspiratorvsP-502 - Remote Display (VLC)vsP-509 - VESDAlink RS232 9P-9P cablevsP-510 - Relays only termination card (VLC-500)vsP-515 - VesdaNET termination card (VLC-505)vsP-715 - Aspirator for VLF-250/500
vESda SParE
ParTS
VES
DA
www.incitefire.com.au • For customer service call 1300 INCITE22 www.incitefire.com.au • For customer service call 1300 INCITE 23
vESda rEPairS
We can arrange repairs for all current models of Vesda detectors. Please contact us
on 1300 INCITE for more information.
vESda TraiNiNg Please contact us on 1300 INCITE for Vesda Accreditation training courses.
NoTEs
VESD
A
rEPairS
TraiNiNg
vsP-000 - Blank plate non EMC with VESDA logovsP-001 - Programmer modulevsP-002 - Display module for LaserPLUSvsP-003 - VesdaNET socketvsP-004 - Display Module for LaserSCANNERvsP-006 - Detector chassis & manifold assembly for LaserPLUSvsP-007 - Remote termination card no relaysvsP-008 - Remote termination card with 7 relaysvsP-009 - Detector chassis & manifold assembly for LaserSCANNERvsP-011 - Recess mounting kit (VLP & VLS)vsP-012 - Remote recess mounting kitvsP-013 - Cover assembly with EMC shields (VLP & VLS)vsP-014 - Head termination card with 7 relaysvsP-015 - Detector aspirator assembly (VLP & VLS)vsP-016 - Head termination card with 12 relays (VLS only)vsP-018 - Filter switch assembly (VLP & VLS)vsP-019 - Filter cover (VLP & VLS)vsP-020 - Screw covers (2)vsP-021 - Pipe adaptors 25mm to 27mm (4)vsP-022 - Mounting box detectorvsP-023 - Front cover (VLC-505)vsP-024 - Front cover (VLC-500)vsP-100 - Blank plate non-EMC, Fire 1 & OK LEDsvsP-102 - Remote relay processor without displayvsP-103 - Remote relay processor without display (VLS)vsP-200 - Blank plate EMC painted, without VESDA logovsP-208 - Remote termination card with 12 relays (VLS only)vsP-300 - Blank plate non EMC without VESDA logovsP-501 - VLC aspiratorvsP-502 - Remote Display (VLC)vsP-509 - VESDAlink RS232 9P-9P cablevsP-510 - Relays only termination card (VLC-500)vsP-515 - VesdaNET termination card (VLC-505)vsP-715 - Aspirator for VLF-250/500
vESda SParE
ParTS
VES
DA
www.incitefire.com.au • For customer service call 1300 INCITE24 www.incitefire.com.au • For customer service call 1300 INCITE 25
VESD
A
PiPES
FiTTiNgS
E700-sP-DCl - Sample point decal (200 roll)
E700-T - Solid ‘T’junction pipe
E700-sP-kIT - Sample point kit, contains: – *• 1 x E700-CSC• 1 x E700-SP• 1 x E700-TA• 1 x E700-SPLR
E700-sP - Sampling point
E700-srb - Base for heat activated sample point
E700-y - 2 into 1 pipejoiner (45°)
E700-sPlr - Samplingpoint label (red)
E700-Ta - Trunk adaptorfor sample points
E700-HasP-kIT - Heat activatedsample point kit, contains: - *
• 1 x E700-HASP• 1 x E700-SRB• 1 x E700-TA• 2 x E700-CSC
*Note: Sample point kits do not include capillary tube.
PiPES
FiTTiNgS
VES
DA
E700-EC - 25mmEnd cap
E700-lb - Long radius90° bend
E700-PJ - Straightcoupling
E700-CT - Capillary tube for sample points
E700-J - 2 into 1 pipe joiner (parallel pipes)
E700-PC - Pipe Clips
E700-CsC - Capillary tube connector
E700-HasP - Heat activated sample point
E700-P - 4 metre Vesdapipe (25mm)
E700-PHFT - Special applications pipe
E700-PF - Freezer roompipe
www.incitefire.com.au • For customer service call 1300 INCITE24 www.incitefire.com.au • For customer service call 1300 INCITE 25
VESD
A
PiPES
FiTTiNgS
E700-sP-DCl - Sample point decal (200 roll)
E700-T - Solid ‘T’junction pipe
E700-sP-kIT - Sample point kit, contains: – *• 1 x E700-CSC• 1 x E700-SP• 1 x E700-TA• 1 x E700-SPLR
E700-sP - Sampling point
E700-srb - Base for heat activated sample point
E700-y - 2 into 1 pipejoiner (45°)
E700-sPlr - Samplingpoint label (red)
E700-Ta - Trunk adaptorfor sample points
E700-HasP-kIT - Heat activatedsample point kit, contains: - *
• 1 x E700-HASP• 1 x E700-SRB• 1 x E700-TA• 2 x E700-CSC
*Note: Sample point kits do not include capillary tube.
PiPES
FiTTiNgS
VES
DA
E700-EC - 25mmEnd cap
E700-lb - Long radius90° bend
E700-PJ - Straightcoupling
E700-CT - Capillary tube for sample points
E700-J - 2 into 1 pipe joiner (parallel pipes)
E700-PC - Pipe Clips
E700-CsC - Capillary tube connector
E700-HasP - Heat activated sample point
E700-P - 4 metre Vesdapipe (25mm)
E700-PHFT - Special applications pipe
E700-PF - Freezer roompipe
www.incitefire.com.au • For customer service call 1300 INCITE26 www.incitefire.com.au • For customer service call 1300 INCITE 27
TGEN - Tone generator card• Tones conform to T3 (AS2220 tones available on request)
mCarD - Message card• 4 individual 15 second messages
~ Alert, evacuate, false alarm and test
• Alert & evac message operate automatically
~ Interrupt tones, play twice, continue tones
• False alarm & test messages operate manually
sTrCarD - Strobe Relay Card• Up to 5amps per circuit • Quiescent current 70mA
• Dimensions 95L x 55W x 25H • End of line 4K7 ohms
• Monitor and switch alert & evacuate strobe indicators
lmu-4 - 4 speaker circuit line monitoring card• 100V line voltage in & out • Maximum load output 250watts per card
• Current draw 90mA • Dimensions 140L x 75W x 22H
• End of line 22K
OwSaCCESSOriES
WA
RN
ING
SYSTEM
S
EwiS
A range of EWIS panels are available in site specific configurations.
Please contact us on 1300 INCITE for a panel to suit your requirements.
TONE gENEraTOrS & aMPliFiErS
Evac-15 - 15Watt Evacuation module• 15watt output • Operating voltage 23-30Vdc
• Standby current 100mA • Loaded current 1A
• Dimensions 170L x 90W x 60H • Maximum speaker impedance 665 ohms
Evac-40 - 40Watt Evacuation module• 40watt output • Operating voltage 23-30Vdc
• Standby current 140mA • Maximum speaker impedance 250 ohms
• Loaded current 2.8A • Dimensions
~ Transformer 100L x 60W x 60H
~ Card 170L x 90W x 60H
Evac-60 - 60Watt Evacuation module• 60watt output • Operating voltage 23-30Vdc
• Standby current 160mA • Dimensions 220L x 210W x 100H
• Loaded current 3.8A • Maximum speaker impedance 166 ohms
General evacuation module features
• Fire indicator board input • 0-9 minute alert to evacuate timer
• Hand held microphone input • Remote mic / background music input
• Output for speaker fault condition • Alert and evacuate strobe relay outputs
• Facility for plug in message card • 100V speaker output with line monitoring
• Tones conform to T3 • 003 keyswitch (Off/Auto/Evac)
(AS2220 tones available on request)
Also available in 120watt and 250watt.
EwiS
OwS
WA
RN
ING
SY
STEM
S
www.incitefire.com.au • For customer service call 1300 INCITE26 www.incitefire.com.au • For customer service call 1300 INCITE 27
TGEN - Tone generator card• Tones conform to T3 (AS2220 tones available on request)
mCarD - Message card• 4 individual 15 second messages
~ Alert, evacuate, false alarm and test
• Alert & evac message operate automatically
~ Interrupt tones, play twice, continue tones
• False alarm & test messages operate manually
sTrCarD - Strobe Relay Card• Up to 5amps per circuit • Quiescent current 70mA
• Dimensions 95L x 55W x 25H • End of line 4K7 ohms
• Monitor and switch alert & evacuate strobe indicators
lmu-4 - 4 speaker circuit line monitoring card• 100V line voltage in & out • Maximum load output 250watts per card
• Current draw 90mA • Dimensions 140L x 75W x 22H
• End of line 22K
OwSaCCESSOriES
WA
RN
ING
SYSTEM
S
EwiS
A range of EWIS panels are available in site specific configurations.
Please contact us on 1300 INCITE for a panel to suit your requirements.
TONE gENEraTOrS & aMPliFiErS
Evac-15 - 15Watt Evacuation module• 15watt output • Operating voltage 23-30Vdc
• Standby current 100mA • Loaded current 1A
• Dimensions 170L x 90W x 60H • Maximum speaker impedance 665 ohms
Evac-40 - 40Watt Evacuation module• 40watt output • Operating voltage 23-30Vdc
• Standby current 140mA • Maximum speaker impedance 250 ohms
• Loaded current 2.8A • Dimensions
~ Transformer 100L x 60W x 60H
~ Card 170L x 90W x 60H
Evac-60 - 60Watt Evacuation module• 60watt output • Operating voltage 23-30Vdc
• Standby current 160mA • Dimensions 220L x 210W x 100H
• Loaded current 3.8A • Maximum speaker impedance 166 ohms
General evacuation module features
• Fire indicator board input • 0-9 minute alert to evacuate timer
• Hand held microphone input • Remote mic / background music input
• Output for speaker fault condition • Alert and evacuate strobe relay outputs
• Facility for plug in message card • 100V speaker output with line monitoring
• Tones conform to T3 • 003 keyswitch (Off/Auto/Evac)
(AS2220 tones available on request)
Also available in 120watt and 250watt.
EwiS
OwS
WA
RN
ING
SY
STEM
S
www.incitefire.com.au • For customer service call 1300 INCITE28 www.incitefire.com.au • For customer service call 1300 INCITE 29
sPsm – 100mm Surface mount speaker• 5 tappings up to 5W • 100V line dual cone fire / evac speaker
• Transformer safety cover • Back box with concealed internal fixings
Also available
smqF – 100mm quick fit surface mount speaker
smqF-b – 100mm black quick fit surface mount speaker
HorN – 10 Watt Horn speaker• 5 tappings from 1.25W – 10W • UV stabilised ABS plastic for long life in the sun
• Weather resistant
HORN-SS – 10 Watt Marine horn speaker• As above, stainless steel fitting for marine/outdoor use
bEaCoN-r - 24VDC Red strobe • No start up current surge • Low current consumption - 90mA
• Flash rate 60/min • Only 75mm deep with shallow base
• IP65 with deep base • Small diameter, only 93mm
• Operating voltage 20-30Vdc
bEaCoN-a - 24VDC Amber strobe• As above with amber lens and base
bEaCoN-T3 - 24VDC Clear strobe• “T3” temporal pattern as required by AS1670.4 - 2004
WA
RN
ING
SYSTEM
S
SPEakErS
hOrNS
STrObES
sPG100 – 100mm Flush mount speaker • 5 tappings up to 5W •100V line dual cone fire / evac speaker
• Transformer safety cover • Uses 100mm grill (SPGG)
Also available
sPG100-lP - 100mm low profile, only 54mm high
sPGG – 100mm Slimline grill• Super slimline grill • Overall diameter of 155mm
• Suits SPG100 & SPG100-LP
Also available
sPGG-b – 100mm black slimline grill
SPQF100 – 100mm Quick fit speaker• Quick to install • Snap fits to any 10-13mm thickness ceiling
• 5 tappings up to 5W • Transformer safety cover
Also available
sPqF100-b – as above in black
sPqF200 – 200mm Quick fit speaker
sPqF200-b – 200mm black quick fit speaker
sPqFTIlEmT – Tile mount bracket for SPQF100• Minimises sag of fibre ceiling tiles • Fits inside tile T-bars for maximum support
• Available for 100mm & 200mm ‘Quick fit’ speakers
T2312a – 140mm Holesaw• Cuts exact size hole for SPQF100 • Complete with arbour
WA
RN
ING
SY
STEM
S
SPEakErS
hOrNS
STrObES
www.incitefire.com.au • For customer service call 1300 INCITE28 www.incitefire.com.au • For customer service call 1300 INCITE 29
sPsm – 100mm Surface mount speaker• 5 tappings up to 5W • 100V line dual cone fire / evac speaker
• Transformer safety cover • Back box with concealed internal fixings
Also available
smqF – 100mm quick fit surface mount speaker
smqF-b – 100mm black quick fit surface mount speaker
HorN – 10 Watt Horn speaker• 5 tappings from 1.25W – 10W • UV stabilised ABS plastic for long life in the sun
• Weather resistant
HORN-SS – 10 Watt Marine horn speaker• As above, stainless steel fitting for marine/outdoor use
bEaCoN-r - 24VDC Red strobe • No start up current surge • Low current consumption - 90mA
• Flash rate 60/min • Only 75mm deep with shallow base
• IP65 with deep base • Small diameter, only 93mm
• Operating voltage 20-30Vdc
bEaCoN-a - 24VDC Amber strobe• As above with amber lens and base
bEaCoN-T3 - 24VDC Clear strobe• “T3” temporal pattern as required by AS1670.4 - 2004
WA
RN
ING
SYSTEM
S
SPEakErS
hOrNS
STrObES
sPG100 – 100mm Flush mount speaker • 5 tappings up to 5W •100V line dual cone fire / evac speaker
• Transformer safety cover • Uses 100mm grill (SPGG)
Also available
sPG100-lP - 100mm low profile, only 54mm high
sPGG – 100mm Slimline grill• Super slimline grill • Overall diameter of 155mm
• Suits SPG100 & SPG100-LP
Also available
sPGG-b – 100mm black slimline grill
SPQF100 – 100mm Quick fit speaker• Quick to install • Snap fits to any 10-13mm thickness ceiling
• 5 tappings up to 5W • Transformer safety cover
Also available
sPqF100-b – as above in black
sPqF200 – 200mm Quick fit speaker
sPqF200-b – 200mm black quick fit speaker
sPqFTIlEmT – Tile mount bracket for SPQF100• Minimises sag of fibre ceiling tiles • Fits inside tile T-bars for maximum support
• Available for 100mm & 200mm ‘Quick fit’ speakers
T2312a – 140mm Holesaw• Cuts exact size hole for SPQF100 • Complete with arbour
WA
RN
ING
SY
STEM
S
SPEakErS
hOrNS
STrObES
www.incitefire.com.au • For customer service call 1300 INCITE30 www.incitefire.com.au • For customer service call 1300 INCITE 31
WA
RN
ING
SYSTEM
S
NoTEssTrrED-amb-lP - Red & Amber strobe set on metal plate• Simple bolt on installation • Sturdy white powder coated steel chassis
• Operating voltage 24Vdc • Conduit knockouts for cable entry
• Low current draw 100mA • Terminal block enables 2,3 or 4 wire operation
• Flash rate 1.5Hz • Dimensions 285L x 122W x 85H
sTrrED-amb-wP - Weatherproof red & amber strobe set• No start up current surge • Low current consumption - 90mA per strobe
• Flash rate 60/min • Operating voltage 20-30Vdc
• IP65 rating • White ABS plastic base
• Dimension 185L x 93W x 100H
wIP – Red warden intercom phone• Selectable line impedance 600Ω or 4.7KΩ • Separate speaker for call tone
• Simple two wire connection • Includes wall mounting bracket
• SSL approved, complies with AS 2220
kaC-wHITE – Conventional white manual call point• Plug ‘n’ play installation • Maximum voltage 30VDC
• Current rating 2 Amps • Operating temperature -30° to +70°
• Anti-tamper facility available
kaC-wHITE-wP - Conventional white waterproof MCP• IP67 rating • Maximum voltage 30VDC
• Current rating 5 Amps • Operating temperature -30° to +70°
• Anti-tamper facility available
Accessories
kaC-Glass - Spare glass, pack of 5 kaC-FlaP - Clear anti-tamper cover
WA
RN
ING
SY
STEM
S
STrObE SETS
MCPwiP
www.incitefire.com.au • For customer service call 1300 INCITE30 www.incitefire.com.au • For customer service call 1300 INCITE 31
WA
RN
ING
SYSTEM
S
NoTEssTrrED-amb-lP - Red & Amber strobe set on metal plate• Simple bolt on installation • Sturdy white powder coated steel chassis
• Operating voltage 24Vdc • Conduit knockouts for cable entry
• Low current draw 100mA • Terminal block enables 2,3 or 4 wire operation
• Flash rate 1.5Hz • Dimensions 285L x 122W x 85H
sTrrED-amb-wP - Weatherproof red & amber strobe set• No start up current surge • Low current consumption - 90mA per strobe
• Flash rate 60/min • Operating voltage 20-30Vdc
• IP65 rating • White ABS plastic base
• Dimension 185L x 93W x 100H
wIP – Red warden intercom phone• Selectable line impedance 600Ω or 4.7KΩ • Separate speaker for call tone
• Simple two wire connection • Includes wall mounting bracket
• SSL approved, complies with AS 2220
kaC-wHITE – Conventional white manual call point• Plug ‘n’ play installation • Maximum voltage 30VDC
• Current rating 2 Amps • Operating temperature -30° to +70°
• Anti-tamper facility available
kaC-wHITE-wP - Conventional white waterproof MCP• IP67 rating • Maximum voltage 30VDC
• Current rating 5 Amps • Operating temperature -30° to +70°
• Anti-tamper facility available
Accessories
kaC-Glass - Spare glass, pack of 5 kaC-FlaP - Clear anti-tamper cover
WA
RN
ING
SY
STEM
S
STrObE SETS
MCPwiP
www.incitefire.com.au • For customer service call 1300 INCITE32 www.incitefire.com.au • For customer service call 1300 INCITE 33
rosHNI - 9-28VDC Electronic sounder• 32 selectable tones • Second tone for two stage alarms
• Low current consumption • Up to 111dB (tone dependent)
• Volume control • Only 75mm deep with shallow base
• IP65 with deep base • Small diameter, only 93mm
• 9V – 28V operation without adjustment
bEaCoN-r - 24VDC Red strobe• No start up current surge • Operating voltage 20-30Vdc
• Flash rate 60/min • Low current consumption - 90mA
• IP65 with deep base • Only 75mm deep with shallow base
• Small diameter, only 93mm
bEaCoN-a - 24VDC Amber strobe• As above with amber lens and base
sTr-lab - Strobe ‘FIRE’ label to suit BEACON-R• Foam PVC label • Complies to AS1670.1 2004
• Pre drilled to suit BEACON-R • Red lettering on white background
FlasHNI - Combined sounder strobe• Volume control • IP65 with deep base
• 2 preset tones • Compact design 92mm deep & 93mm dia.
• Up to 101dB at 1 metre • Low current consumption - 68mA (average)
• Flash rate 60/min • Automatic sounder/strobe synchronisation
• Operating voltage 18-30Vdc
squasHNI – Sounder• Fixing platform for Hochiki detector bases • Blank cover for use as stand alone sounder
• Colour matched to Hochiki detectors • Operating voltage 10-28Vdc
• Operating current 8-35mA • Ultra slim profile for unobtrusive installation
(Tone dependant) (30mm deep)
squasNImICro – Low current sounder• Ultra low 3mA current consumption • Blank cover for use as stand alone sounder
• Colour matched to Hochiki detectors • Fixing platform for Hochiki detector base
SOuNdErS
STrObES
AN
CILLA
RIES
kaC-rED – Conventional red manual call point• Plug ‘n’ play installation • 470Ω resistor fitted
• Maximum voltage 30VDC • Current rating 2 Amps
• Operating temperature -30° to +70° • Anti-tamper facility available
kaC-rED-rP - Conventional red rainproof MCP (IP55)• IP55 rating • Maximum voltage 30VDC
• Current rating 3 Amps • Operating temperature -30° to +70°
• Anti-tamper facility available
kaC-rED-wP - Conventional red waterproof MCP (IP67)• IP67 rating • Maximum voltage 30VDC
• Current rating 5 Amps • Operating temperature -30° to +70°
• Anti-tamper facility available
Also available
kaC-wHITE – Conventional white manual call pointkaC-wHITE-rP - Conventional white rainproof MCP (IP55)kaC-wHITE-wP - Conventional white waterproof MCP (IP67)kaC-GrEEN - Conventional green manual call point
Accessories
kaC-Glass - Spare glass, pack of 5kaC-FlaP - Clear anti-tamper cover for all KAC BGA
MaNual
Call POiNTS
AN
CIL
LAR
IES
www.incitefire.com.au • For customer service call 1300 INCITE32 www.incitefire.com.au • For customer service call 1300 INCITE 33
rosHNI - 9-28VDC Electronic sounder• 32 selectable tones • Second tone for two stage alarms
• Low current consumption • Up to 111dB (tone dependent)
• Volume control • Only 75mm deep with shallow base
• IP65 with deep base • Small diameter, only 93mm
• 9V – 28V operation without adjustment
bEaCoN-r - 24VDC Red strobe• No start up current surge • Operating voltage 20-30Vdc
• Flash rate 60/min • Low current consumption - 90mA
• IP65 with deep base • Only 75mm deep with shallow base
• Small diameter, only 93mm
bEaCoN-a - 24VDC Amber strobe• As above with amber lens and base
sTr-lab - Strobe ‘FIRE’ label to suit BEACON-R• Foam PVC label • Complies to AS1670.1 2004
• Pre drilled to suit BEACON-R • Red lettering on white background
FlasHNI - Combined sounder strobe• Volume control • IP65 with deep base
• 2 preset tones • Compact design 92mm deep & 93mm dia.
• Up to 101dB at 1 metre • Low current consumption - 68mA (average)
• Flash rate 60/min • Automatic sounder/strobe synchronisation
• Operating voltage 18-30Vdc
squasHNI – Sounder• Fixing platform for Hochiki detector bases • Blank cover for use as stand alone sounder
• Colour matched to Hochiki detectors • Operating voltage 10-28Vdc
• Operating current 8-35mA • Ultra slim profile for unobtrusive installation
(Tone dependant) (30mm deep)
squasNImICro – Low current sounder• Ultra low 3mA current consumption • Blank cover for use as stand alone sounder
• Colour matched to Hochiki detectors • Fixing platform for Hochiki detector base
SOuNdErS
STrObES
AN
CILLA
RIES
kaC-rED – Conventional red manual call point• Plug ‘n’ play installation • 470Ω resistor fitted
• Maximum voltage 30VDC • Current rating 2 Amps
• Operating temperature -30° to +70° • Anti-tamper facility available
kaC-rED-rP - Conventional red rainproof MCP (IP55)• IP55 rating • Maximum voltage 30VDC
• Current rating 3 Amps • Operating temperature -30° to +70°
• Anti-tamper facility available
kaC-rED-wP - Conventional red waterproof MCP (IP67)• IP67 rating • Maximum voltage 30VDC
• Current rating 5 Amps • Operating temperature -30° to +70°
• Anti-tamper facility available
Also available
kaC-wHITE – Conventional white manual call pointkaC-wHITE-rP - Conventional white rainproof MCP (IP55)kaC-wHITE-wP - Conventional white waterproof MCP (IP67)kaC-GrEEN - Conventional green manual call point
Accessories
kaC-Glass - Spare glass, pack of 5kaC-FlaP - Clear anti-tamper cover for all KAC BGA
MaNual
Call POiNTS
AN
CIL
LAR
IES
www.incitefire.com.au • For customer service call 1300 INCITE34 www.incitefire.com.au • For customer service call 1300 INCITE 35
sPsm – 100mm Surface mount speaker• 5 tappings up to 5W • 100V line dual cone fire / evac speaker
• Transformer safety cover • Back box with concealed internal fixings
Also available
smqF – 100mm quick fit surface mount speaker
smqF-b – 100mm black quick fit surface mount speaker
HorN – 10 Watt Horn speaker• 5 tappings from 1.25W – 10W • UV stabilised ABS plastic for long life in the sun
• Weather resistant • Also available for marine use (stainless steel fittings)
HorN-ss – 10 Watt Marine horn speaker• As above, stainless steel fitting for marine/outdoor use
NoTEs
SPEakErS
hOrNS
AN
CILLA
RIES
sPG100 – 100mm Flush mount speaker• 5 tappings up to 5W • 100V line dual cone fire / evac speaker
• Transformer safety cover • Uses 100mm grill (SPGG)
Also available
sPG100-lP - 100mm low profile, only 54mm high
sPGG – 100mm Slimline grill• Super slimline grill • Overall diameter of 155mm
• Suits SPG100 & SPG100-LP
Also available
sPGG-b – 100mm black slimline grill
sPqF100 – 100mm Quick fit speaker• Quick to install • Snap fits to any 10-13mm thickness ceiling
• 5 tappings up to 5W • Transformer safety cover
Also available
sPqF100-b – as above in black
sPqF200 – 200mm Quick fit speaker
sPqF200-b – 200mm black quick fit speaker
sPqFTIlEmT – Tile mount bracket for SPQF100• Minimises sag of fibre ceiling tiles • Available for 100mm & 200mm ‘Quick fit’ speakers
• Fits inside tile T-bars for maximum support
T2312a – 140mm Holesaw• Complete with arbour • Cuts exact size hole for SPQF100
SPEakErS
hOrNS
AN
CIL
LAR
IES
www.incitefire.com.au • For customer service call 1300 INCITE34 www.incitefire.com.au • For customer service call 1300 INCITE 35
sPsm – 100mm Surface mount speaker• 5 tappings up to 5W • 100V line dual cone fire / evac speaker
• Transformer safety cover • Back box with concealed internal fixings
Also available
smqF – 100mm quick fit surface mount speaker
smqF-b – 100mm black quick fit surface mount speaker
HorN – 10 Watt Horn speaker• 5 tappings from 1.25W – 10W • UV stabilised ABS plastic for long life in the sun
• Weather resistant • Also available for marine use (stainless steel fittings)
HorN-ss – 10 Watt Marine horn speaker• As above, stainless steel fitting for marine/outdoor use
NoTEs
SPEakErS
hOrNS
AN
CILLA
RIES
sPG100 – 100mm Flush mount speaker• 5 tappings up to 5W • 100V line dual cone fire / evac speaker
• Transformer safety cover • Uses 100mm grill (SPGG)
Also available
sPG100-lP - 100mm low profile, only 54mm high
sPGG – 100mm Slimline grill• Super slimline grill • Overall diameter of 155mm
• Suits SPG100 & SPG100-LP
Also available
sPGG-b – 100mm black slimline grill
sPqF100 – 100mm Quick fit speaker• Quick to install • Snap fits to any 10-13mm thickness ceiling
• 5 tappings up to 5W • Transformer safety cover
Also available
sPqF100-b – as above in black
sPqF200 – 200mm Quick fit speaker
sPqF200-b – 200mm black quick fit speaker
sPqFTIlEmT – Tile mount bracket for SPQF100• Minimises sag of fibre ceiling tiles • Available for 100mm & 200mm ‘Quick fit’ speakers
• Fits inside tile T-bars for maximum support
T2312a – 140mm Holesaw• Complete with arbour • Cuts exact size hole for SPQF100
SPEakErS
hOrNS
AN
CIL
LAR
IES
www.incitefire.com.au • For customer service call 1300 INCITE36 www.incitefire.com.au • For customer service call 1300 INCITE 37
Dm500 - Doormouse 50KG wall mount door holder• 50Kg holding force • Compact white ABS plastic housing (wall mount)
• Rated voltage 24VDC • Operating current 43mA
• Zero residual magnetism
DH84-500 - 50KG Floor mount door holder• Robust aluminium construction • 50Kg holding force
• Rated voltage 24VDC • Operating current 43mA
• Zero residual magnetism
DHwP120 – Weatherproof wall mounted door holder• Robust steel construction • 120Kg holding force
• IP65 rated • Rated voltage 24VDC
• Operating current 0.29A
DP-200 – 200mm Universal mount door holder• 200mm steel post (white) • Rated voltage 24VDC
• Floor, ceiling or wall mount • Operating current 43mA
• 50kg holding force • Zero residual magnetism
DH-CHromE – Chrome finish door holder• 11.5Kg holding force • Rated voltage 24VDC
• Operating Current 66mA • Chrome finish surface mount kit available
• High quality chrome finish c/w matching keeper plate, also available in brass finish
DH - 1350 Wall mount door holder• 50Kg holding force • Aluminium & thermoplastic housing (wall mount)
• Rated voltage 24VDC • Operating current 45mA
DH150 - 150mm Post Floor/Wall mount door holder• Floor or wall mount with 150mm post • 50Kg holding force
• Rated voltage 24VDC • Operating current 45mA
DH300 - As above with 300mm post
Drs004 – Door Release Switch• Press switch to release door holder
MagNETiC dOOr
hOldErS
AN
CILLA
RIES
sTrrED-amb-lP - Red & Amber strobe set on metal plate• Low current draw 100mA • Sturdy white powder coated steel chassis
• Simple bolt on installation • Conduit knockouts for cable entry
• Operating voltage 24Vdc • Dimensions 285L x 122W x 85H
• Flash rate 1.5Hz • Terminal block enables 2,3 or 4 wire operation
sTrrED-amb-wP - Weatherproof red & amber strobe set• No start up current surge • Flash rate 60/min
• Operating voltage 20-30Vdc • IP65 rating
• White ABS plastic base • Dimension 185L x 93W x 100H
• Low current consumption - 90mA per strobe
wIP – Red warden intercom phone• Separate speaker for call tone • Selectable line impedance 600Ω or 4.7KΩ
• Simple two wire connection • SSL approved, complies with AS 2220
• Includes wall mounting bracket
NoTEs
STrObE SETS
wiP
AN
CIL
LAR
IES
www.incitefire.com.au • For customer service call 1300 INCITE36 www.incitefire.com.au • For customer service call 1300 INCITE 37
Dm500 - Doormouse 50KG wall mount door holder• 50Kg holding force • Compact white ABS plastic housing (wall mount)
• Rated voltage 24VDC • Operating current 43mA
• Zero residual magnetism
DH84-500 - 50KG Floor mount door holder• Robust aluminium construction • 50Kg holding force
• Rated voltage 24VDC • Operating current 43mA
• Zero residual magnetism
DHwP120 – Weatherproof wall mounted door holder• Robust steel construction • 120Kg holding force
• IP65 rated • Rated voltage 24VDC
• Operating current 0.29A
DP-200 – 200mm Universal mount door holder• 200mm steel post (white) • Rated voltage 24VDC
• Floor, ceiling or wall mount • Operating current 43mA
• 50kg holding force • Zero residual magnetism
DH-CHromE – Chrome finish door holder• 11.5Kg holding force • Rated voltage 24VDC
• Operating Current 66mA • Chrome finish surface mount kit available
• High quality chrome finish c/w matching keeper plate, also available in brass finish
DH - 1350 Wall mount door holder• 50Kg holding force • Aluminium & thermoplastic housing (wall mount)
• Rated voltage 24VDC • Operating current 45mA
DH150 - 150mm Post Floor/Wall mount door holder• Floor or wall mount with 150mm post • 50Kg holding force
• Rated voltage 24VDC • Operating current 45mA
DH300 - As above with 300mm post
Drs004 – Door Release Switch• Press switch to release door holder
MagNETiC dOOr
hOldErS
AN
CILLA
RIES
sTrrED-amb-lP - Red & Amber strobe set on metal plate• Low current draw 100mA • Sturdy white powder coated steel chassis
• Simple bolt on installation • Conduit knockouts for cable entry
• Operating voltage 24Vdc • Dimensions 285L x 122W x 85H
• Flash rate 1.5Hz • Terminal block enables 2,3 or 4 wire operation
sTrrED-amb-wP - Weatherproof red & amber strobe set• No start up current surge • Flash rate 60/min
• Operating voltage 20-30Vdc • IP65 rating
• White ABS plastic base • Dimension 185L x 93W x 100H
• Low current consumption - 90mA per strobe
wIP – Red warden intercom phone• Separate speaker for call tone • Selectable line impedance 600Ω or 4.7KΩ
• Simple two wire connection • SSL approved, complies with AS 2220
• Includes wall mounting bracket
NoTEs
STrObE SETS
wiP
AN
CIL
LAR
IES
www.incitefire.com.au • For customer service call 1300 INCITE38 www.incitefire.com.au • For customer service call 1300 INCITE 39
POwEr SuPPliES
A range of Stand alone power supplies and batteries are available. Please contact us on
1300 INCITE for a power supply to suit your requirements.
SigNS
A range of warning signs are available. Contact us on 1300 INCITE for more information.
TEST EquiPMENT
smokE-HsG – Canned smoke (70.5g)
smokE-PEN – Handheld pen style smoke generator• complete with six smoke sticks • 360 smoke tests of 30 seconds each
• 6 smoke sticks equals approx. 3 hours continuous smoke
smokE-rEF – Refill pack for smoke pen (6 sticks only)
sb-2.5 – Smoke Bomb cartridges (5 pack)• Grey/white smoke bombs • Burn time approx 240 sec
PuNksTICk – Smoke sticks (50 pack)• For use with Hochiki smoke tester (TSE-A100)
TsE-a100 – Hochiki smoke generator detector tester
Also available for hire
Spectrex flame detector testerHochiki beam detector (SPC-AS) tester
AN
CILLA
RIES
POwEr SuPPliES
SigNS
TEST EquiPMENT
rEMOTE iNdiCaTOrS
“Fire alarm in…”rEm-Cr - Coolroom
rEm-Cs - CoNCEalED sPaCE
rEm-Cu - CuPboarD
rEm-DC - DuCT
rEm-ra - rETurN aIr
rEm-lIFT - lIFT sHaFT
rEm-rF - rooF sPaCE
rEm-rm - room
rEm-sb - swITCHboarD
rEm-Cl - CEIlING
rEm-uF - uNDEr Floor
baTTEriES
Batt/1.3 - 12V 1.3A/hr Sealed lead acid battery
Batt/7 - 12V 7A/hr Sealed lead acid battery
Batt/12 - 12V 12A/hr Sealed lead acid battery
Batt/18 - 12V 18A/hr Sealed lead acid battery
Batt/26 - 12V 26A/hr Sealed lead acid battery
Batt/33 - 12V 33A/hr Sealed lead acid battery
Batt/40 - 12V 40A/hr Sealed lead acid battery
Batt/65 - 12V 65A/hr Sealed lead acid battery
Batt/85 - 12V 85A/hr Sealed lead acid battery
Batt/100 - 12V 100A/hr Sealed lead acid battery
SSL Listing: afp-1636
A range of other size batteries are available. Please contact us on 1300 INCITE for a battery to
suit your requirements.
rEMOTE iNdiCaTOrS
baTTEriES
AN
CIL
LAR
IES
www.incitefire.com.au • For customer service call 1300 INCITE38 www.incitefire.com.au • For customer service call 1300 INCITE 39
POwEr SuPPliES
A range of Stand alone power supplies and batteries are available. Please contact us on
1300 INCITE for a power supply to suit your requirements.
SigNS
A range of warning signs are available. Contact us on 1300 INCITE for more information.
TEST EquiPMENT
smokE-HsG – Canned smoke (70.5g)
smokE-PEN – Handheld pen style smoke generator• complete with six smoke sticks • 360 smoke tests of 30 seconds each
• 6 smoke sticks equals approx. 3 hours continuous smoke
smokE-rEF – Refill pack for smoke pen (6 sticks only)
sb-2.5 – Smoke Bomb cartridges (5 pack)• Grey/white smoke bombs • Burn time approx 240 sec
PuNksTICk – Smoke sticks (50 pack)• For use with Hochiki smoke tester (TSE-A100)
TsE-a100 – Hochiki smoke generator detector tester
Also available for hire
Spectrex flame detector testerHochiki beam detector (SPC-AS) tester
AN
CILLA
RIES
POwEr SuPPliES
SigNS
TEST EquiPMENT
rEMOTE iNdiCaTOrS
“Fire alarm in…”rEm-Cr - Coolroom
rEm-Cs - CoNCEalED sPaCE
rEm-Cu - CuPboarD
rEm-DC - DuCT
rEm-ra - rETurN aIr
rEm-lIFT - lIFT sHaFT
rEm-rF - rooF sPaCE
rEm-rm - room
rEm-sb - swITCHboarD
rEm-Cl - CEIlING
rEm-uF - uNDEr Floor
baTTEriES
Batt/1.3 - 12V 1.3A/hr Sealed lead acid battery
Batt/7 - 12V 7A/hr Sealed lead acid battery
Batt/12 - 12V 12A/hr Sealed lead acid battery
Batt/18 - 12V 18A/hr Sealed lead acid battery
Batt/26 - 12V 26A/hr Sealed lead acid battery
Batt/33 - 12V 33A/hr Sealed lead acid battery
Batt/40 - 12V 40A/hr Sealed lead acid battery
Batt/65 - 12V 65A/hr Sealed lead acid battery
Batt/85 - 12V 85A/hr Sealed lead acid battery
Batt/100 - 12V 100A/hr Sealed lead acid battery
SSL Listing: afp-1636
A range of other size batteries are available. Please contact us on 1300 INCITE for a battery to
suit your requirements.
rEMOTE iNdiCaTOrS
baTTEriES
AN
CIL
LAR
IES
www.incitefire.com.au • For customer service call 1300 INCITE40 www.incitefire.com.au • For customer service call 1300 INCITE 41
iNTriNSiCally SaFE dETECTOrS
slr-E-Is – Hochiki intrinsically safe conventional photo electric smoke detectorDCD-1E-Is- Hochiki intrinsically safe conventional thermal detectorYBN-R/4IS – Hochiki intrinsically safe conventional baseSpectrex - Flame detectors
Intrinsically safe barriers & warning devices are also available. Please contact us on 1300 INCITEfor more information.
MariNE dETECTOrS
slr-Em – Hochiki marine conventional photo electric smoke detectorDCD-rE1Em - Hochiki marine conventional thermal detectorYBN-R/4M – Hochiki marine conventional base
OThEr
vaNGuarD – Vandal proof steel cage for Hochiki detectors
NoTEs
SPEC
IAL A
PP
LICA
TION
S
iNTriNSiCally SaFE
MariNE
Spectrex flame detectorsA range of Spectrex flame detectors are available including UV, IR, UV/IR, IR3 & IR3 CCTV. Please
contact us on 1300 INCITE for information and specification on flame detectors to suit your
requirements.
CCTV Smoke DetectionPlease contact us on 1300 INCITE for information and specification on CCTV smoke detection.
Firewire (linear heat cable)Please contact us on 1300 INCITE for information and specification on Firewire.
AspiratedPlease refer to the Vesda section on page 18
NoTEs
SPEC
IAL
AP
PLI
CA
TIO
NS
SPECial aPPliCaTiON
dETECTiON
www.incitefire.com.au • For customer service call 1300 INCITE40 www.incitefire.com.au • For customer service call 1300 INCITE 41
iNTriNSiCally SaFE dETECTOrS
slr-E-Is – Hochiki intrinsically safe conventional photo electric smoke detectorDCD-1E-Is- Hochiki intrinsically safe conventional thermal detectorYBN-R/4IS – Hochiki intrinsically safe conventional baseSpectrex - Flame detectors
Intrinsically safe barriers & warning devices are also available. Please contact us on 1300 INCITEfor more information.
MariNE dETECTOrS
slr-Em – Hochiki marine conventional photo electric smoke detectorDCD-rE1Em - Hochiki marine conventional thermal detectorYBN-R/4M – Hochiki marine conventional base
OThEr
vaNGuarD – Vandal proof steel cage for Hochiki detectors
NoTEs
SPEC
IAL A
PP
LICA
TION
S
iNTriNSiCally SaFE
MariNE
Spectrex flame detectorsA range of Spectrex flame detectors are available including UV, IR, UV/IR, IR3 & IR3 CCTV. Please
contact us on 1300 INCITE for information and specification on flame detectors to suit your
requirements.
CCTV Smoke DetectionPlease contact us on 1300 INCITE for information and specification on CCTV smoke detection.
Firewire (linear heat cable)Please contact us on 1300 INCITE for information and specification on Firewire.
AspiratedPlease refer to the Vesda section on page 18
NoTEs
SPEC
IAL
AP
PLI
CA
TIO
NS
SPECial aPPliCaTiON
dETECTiON
www.incitefire.com.au • For customer service call 1300 INCITE42 www.incitefire.com.au • For customer service call 1300 INCITE 43
MISC
ELLAN
EOU
S
Components
FP01 – Assorted fuse pack
rP01 – Assorted resistor pack
rElay – 24V relay & mounting base 24V 10A DPDT
TErm01 – Terminal strip block (12)
• Rated 400V @ 6A • 2.8mm cable entry with wire protection
TErm02 - Terminal strip block (12)
• Rated 400V @ 10A • 3.4mm cable entry with wire protection
CrImPlG – Assorted crimp lugs pack
Interface Leads
LD/USB-DB9 – 35cm lead, USB A to DB9 serial
• Not compatible with all laptops • For use in conjunction with FireNet download cable
LD/DB9-DB9X – FireNet download cable
vsP-509 – VESDAlink cable
• Suits Vesda HLI - PC • Suits Vesda handheld programmer (VHH-100)
CablE
CablErED - Red twin 24/0.20 100mtr
Also available
Fire rated cable. Please contact us on 1300 INCITE
TOOlS
SuNdriES
Tools
T2312a – 140mm Holesaw - to suit SPQF100 - 100mm quick fit speaker
GassolD – 100W gas soldering iron – auto ignition
solDEr – Tube of 1mm resin core solder (3m)
HEaDlED – 3 LED torch c/w headband
CrImPTl – Ratchet crimper, 0.25mm – 6.0mm range
wIrEsT – Automatic wire stripper
Aerosols
DusToFF – Can compressed air – suits detector & internal panel cleaning
buTaNE – Can butane gas to suit GASSOLD
ClEaNsol – Electronic cleaning solvent
Fixings
CT100 – 100mm cable ties (100 pack, natural color)
CT200 – 200mm cable ties (100 pack, natural color)
CTmNT – Adhesive cable tie mounts (25 pack)
sPIral – Spiral binding for cable looms (per metre)
HEaTsrk – Assorted heatshrink pack
DsTaPE – Double sided tape, 12mm wide x 1mm thick x 2mtrs
Enclosures
Jb-ub2 – ABS grey plastic box for field modules etc.
• Dimensions – 197L x 112W x 62H
A range of powder coated metal enclosure with 003 locks are available.
Please contact us on 1300 INCITE for an enclosure to suit your requirements.
MIS
CEL
LAN
EOU
S
TOOlS
SuNdriES
www.incitefire.com.au • For customer service call 1300 INCITE42 www.incitefire.com.au • For customer service call 1300 INCITE 43
MISC
ELLAN
EOU
S
Components
FP01 – Assorted fuse pack
rP01 – Assorted resistor pack
rElay – 24V relay & mounting base 24V 10A DPDT
TErm01 – Terminal strip block (12)
• Rated 400V @ 6A • 2.8mm cable entry with wire protection
TErm02 - Terminal strip block (12)
• Rated 400V @ 10A • 3.4mm cable entry with wire protection
CrImPlG – Assorted crimp lugs pack
Interface Leads
LD/USB-DB9 – 35cm lead, USB A to DB9 serial
• Not compatible with all laptops • For use in conjunction with FireNet download cable
LD/DB9-DB9X – FireNet download cable
vsP-509 – VESDAlink cable
• Suits Vesda HLI - PC • Suits Vesda handheld programmer (VHH-100)
CablE
CablErED - Red twin 24/0.20 100mtr
Also available
Fire rated cable. Please contact us on 1300 INCITE
TOOlS
SuNdriES
Tools
T2312a – 140mm Holesaw - to suit SPQF100 - 100mm quick fit speaker
GassolD – 100W gas soldering iron – auto ignition
solDEr – Tube of 1mm resin core solder (3m)
HEaDlED – 3 LED torch c/w headband
CrImPTl – Ratchet crimper, 0.25mm – 6.0mm range
wIrEsT – Automatic wire stripper
Aerosols
DusToFF – Can compressed air – suits detector & internal panel cleaning
buTaNE – Can butane gas to suit GASSOLD
ClEaNsol – Electronic cleaning solvent
Fixings
CT100 – 100mm cable ties (100 pack, natural color)
CT200 – 200mm cable ties (100 pack, natural color)
CTmNT – Adhesive cable tie mounts (25 pack)
sPIral – Spiral binding for cable looms (per metre)
HEaTsrk – Assorted heatshrink pack
DsTaPE – Double sided tape, 12mm wide x 1mm thick x 2mtrs
Enclosures
Jb-ub2 – ABS grey plastic box for field modules etc.
• Dimensions – 197L x 112W x 62H
A range of powder coated metal enclosure with 003 locks are available.
Please contact us on 1300 INCITE for an enclosure to suit your requirements.
MIS
CEL
LAN
EOU
S
TOOlS
SuNdriES
www.incitefire.com.au • For customer service call 1300 INCITE www.incitefire.com.au • For customer service call 1300 INCITE
RIGHTS IN RELATION TO GOODS18 Seller reserves the following rights in relation to the goods until all accounts owed by the Buyer to the Seller are fully paid: 18.1 legal ownership of the goods; 18.2 to enter the Buyer’s premises (or the premises of any associated company or agent where the goods are located) without liability for trespass or any resulting damage and retake possession of the goods irrespective of the manner of their attachment to any realty; and 18.3 to keep or resell any goods repossessed pursuant to (2) above.TITLE TO GOODS19 Property in each unit of the goods shall remain with Seller until all monies owing to Seller on any account whatsoever have been paid (“the Debts”). The Buyer shall in the meantime take custody of the goods and retain them as Seller’s trustee, fiduciary agent and bailee and shall store the goods in such a manner that they are readily distinguishable from other goods owned by the Buyer or other persons (“the Other Goods”). Pending resale or utilisation in any manufacturing or other process, the goods are to be kept separate from the Other Goods and properly marked, stored, protected and insured. 19.1 The Buyer may resell the goods, but only as fiduciary agent and trustee for the Seller, by way of bona fide sale at full market value and in the ordinary course of its business. 19.2 Until the Debts have been paid in full the Buyer shall hold such part of the money it receives from:- 19.2.1 any sub-sale of the goods under the immediately preceding subclause; and 19.2.2 the proceeds of any sale of any products into which the goods have been mixed or converted by any process as equals the amount of the debts at the time the money is received (“the Proceeds”) as bailee and fiduciary agent and trustee for the Seller. 19.3 The Buyer expressly acknowledges that it is bound by such fiduciary obligation and acknowledges that: 19.3.1 it must hold the Proceeds on trust for the Seller. 19.3.2 it must place the whole of the Proceeds in an account separate from its own moneys (“the Proceeds Account”). 19.3.3 it must maintain the Proceeds Account separate from its own moneys at all times. 19.3.4 it must maintain proper records for the Proceeds Account. 19.3.5 it must not assign or encumber the Proceeds or do any other act in derogation of the Seller’s legal or beneficial interests. 19.3.6 it must account to the Seller on demand for all moneys standing to the credit of such account; 19.3.7 the Seller may appropriate payments to such goods and accounts as it thinks fit, notwithstanding any contrary appropriation by the Buyer; 19.3.8 for the purposes of identification of different consignments of goods purchased from Seller and receipt of Proceeds, the Buyer agrees that the principle of “Last In, First Out” shall be applied to any items which cannot be distinguished. 19.3.9 receipt by the Buyer of payment for the sale of any products into which the goods have been mixed or converted by any process shall be treated as evidence that it has received Proceeds; and 19.3.10 the Seller may trace the Proceeds in equity.BUYER’S PROPERTY20 Any property of the Buyer under the Seller’s custody or control shall be entirely at the Buyer’s risk as regards loss or damage caused to the property or by it. The Buyer expressly grants to the Seller such rights of sale as would arise if the Seller had displayed a notice under the Disposal of Uncollected Goods Act, whether or not the Seller had displayed such a notice.STORAGE21 The Seller reserves the right to make a reasonable charge for storage if delivery instructions are not provided by the Buyer within fourteen days after a request by the Seller for such information.GOODS SOLD22 All goods to be supplied by Seller shall be as described on the purchase order agreed by the Seller and the Buyer and the description on such purchase order modified as so agreed shall prevail over all other descriptions including any Buyer’s specification or enquiry. The goods supplied are not designed or adapted for use in adverse industrial atmosphere or weather or abnormal operating conditions of any kind.CANCELLATION23 No order may be cancelled except with consent in writing and on terms which will indemnify the Seller against all losses.PLACE OF CONTRACT24 The contract for the sale of the goods is made in the state inwhich the sale originates and the parties agree to submit all disputes arising between them to the courts of such state at any court competent to hear appeals therefrom.NO WAIVER25 The failure of any party to enforce the provisions of this agreement or to exercise any rights expressed in this agreement shall not be a waiver of such provisions or rights and shall not affect the enforcement of this agreement. The exercise by any party of any of its rights expressed in this agreement shall not preclude or prejudice such party from exercising the same or any other rights it may have irrespective of any previous action taken by that party.FORCE MAJEURE26 Where a party is unable, wholly or in part, by reason of an act of God, strike, lockout or other interference with work, war declared or undeclared, blockade, disturbance, lightning, fire, earthquake, storm, flood, explosion, governmental or quasi-governmental restraint, expropriation prohibition intervention direct or embargo, unavailability or delay in availability of equipment or transport, inability or delay in obtaining governmental or quasi-gover mental approvals consents permits licences authorities or allocations, and any other cause whether of the kind specifically enumerated above or otherwise which is not reasonably within the control of the party affect (`force majeure’), to carry out any obligation under this agreement and that party: 26.1 gives the other party prompt notice of that force majeure with reasonably full particulars thereof, and, insofar as known, the probable extent of which it will be unable to perform or be delayed in performing that obligation; and 26.2 uses all possible diligence to remove that force majeure as quickly as possible; that obligation is suspended so far as it is affected by force majeure during the continuance thereof provided that; 26.3 an obligation to pay money is never excused by force majeure. 26.4 the requirement that any force majeure shall be removed with all possible diligence shall not require the settlement of strikes, lockouts or other labour disputes, or claims or demands by any government on terms contrary to the wishes of the party affected.EXCLUSION OF NEGLIGENCE27 The Seller shall not be liable to the Buyer in contract or in tort arising out of, or in connection with, or relating to, the performance of the goods or any such breach of these conditions or of any fact, matter or thing relating to the goods or error (whether negligent of a breach of contract or not) in information supplied to the Buyer or a user before or after the date of the Buyer’s or user’s use of the goods.SEVERANCE28 If any of the terms or conditions is deemed to be unlawful or unenforceable, such term or condition shall be severed and all other terms and conditions shall remain in force.
INTERPRETATION1 In these conditions: 1.1 ‘Buyer’ means the buyer of any goods including any specified overleaf. 1.2 ‘Conditions’ or ‘these conditions’ means these Terms and Conditions of Sale. 1.3 ‘Costs’ includes Goods and Services Tax (GST) payable as a result of any taxable supply (including the release of any obligation arising under these conditions by the Seller to the Buyer) or as a result of an order made in any proceedings between the Seller and the Buyer. 1.4 ‘Goods’ means any products and services specified including any overleaf. 1.5 ‘Seller’ means INCITE FIRE Pty Limited (ACN 089 243 989) and its assigns or successors and each corporation (within the meaning of that term in Section 9 of the Corporations Law) which now or hereafter is or shall be deemed to be related to the Seller (within the meaning of Section 50 of the Corporations Law). 1.6 Nothing in these conditions shall be read or applied so as to exclude, restrict or modify or have the effect of excluding, restricting or modifying any condition, warranty, guarantee, right or remedy implied by law (including the Trade Practices Act 1974) and which by law cannot be excluded, restricted or modified.GENERAL2 These conditions (which shall only be waived or varied in writing signed by the Seller) shall prevail over all conditions of the Buyer’s order to the extent of any inconsistency.TERMS OF SALE3 The goods and all other products sold by the Seller are sold on these terms and conditions.4 Where any payment from the Buyer to the Seller is overdue the Seller may without notice demand from the Buyer payment of all amounts due for any goods sold by the Seller to the Buyer.SAMPLES, VARIANCES, ETC5 All samples, specifications, drawings, and particulars of dimensions, gauge, shade, colour or quality submitted to the Seller are approximate only and any deviation shall not be taken to vitiate any contract with the Seller or form grounds for any claim against the Seller.DELIVERY 6 Where the Seller arranges delivery it is as agent of the Buyer and at the Buyer’s risk and in that circumstance the sale is to be treated as if it had been made at the Seller’s premises.7 The delivery times made known to the Buyer are estimates only and Seller shall not be liable for to late delivery or non-delivery and under no circumstances shall the Seller be liable for any loss, damage or delay occasioned to the Buyer or its customers arising from late or non-delivery of the goods.LOSS OR DAMAGE IN TRANSIT8 The Seller is not responsible for any loss or damage to goods in transit. SELLER’S LIABILITIES9 The Seller shall not be liable for and the Buyer releases the Seller from any claims in respect of faulty or defective design of any goods supplied unless such design has been wholly prepared by the Seller and the responsibility for any claim has been specifically accepted by the Seller in writing and in any event the Seller’s liability hereunder shall be strictly limited to the replacement of defective goods in accordance with these conditions.10 Except as provided in these conditions, all express and implied warranties, guarantees and conditions under statute or general law as to merchantability, description, quality, suitability or fitness of the goods for any purpose or as to design, assembly, installation, materials or workmanship or otherwise are hereby expressly excluded. The Seller shall not be liable for physical or financial injury, loss or damage or for consequential loss or damage of any kind arising out of the supply, layout, assembly, installation, materials or workmanship or otherwise are hereby expressly excluded and the Seller shall not be liable for physical or financial injury, loss or damage or for consequential loss or damage of any kind arising out of the supply, layout, assembly, installation or operation of the goods or arising out of the Seller’s negligence or in any way whatsoever.11 The Buyer acknowledges its duty to inspect the entire order to ensure its satisfaction with the order.12 The Seller’s liability for a breach of a condition or warranty implied by Division 2 of Pt V of the Trade Practices Act 1974 (other than s 69) is hereby limited to:- 12.1 in the case of goods, any one or more of the following: 12.1.1 the replacement of the goods or the supply of equivalent goods; 12.1.2 the repair of the goods; 12.1.3 the payment of the cost of replacing the goods or of acquiring equivalent goods; 12.1.4 the payment of the cost of having the goods repaired; or 12.2 in the case of services: 12.2.1 the supplying of the services again; or 12.2.2 the payment of the cost of having the services supplied again. 12.3 The Seller’s liability under s 74H of the Trade Practices Act 1975 is expressly limited to a liability to pay to the Buyer an amount equal to: 12.3.1 the cost of replacing the goods; 12.3.2 the cost of obtaining equivalent goods; or 12.3.3 the cost of having the goods repaired, whichever is the lowest amount.PRICES13 Unless otherwise stated all prices quoted by the Seller are exclusive of GST. Prices quoted are those ruling at the date of issue of quotation and are based on rates of freight, insurance, customs duties, currency exchange, shipping expenses, sorting and stacking charges, cartage, rates of weights, cost of materials and other charges affecting the cost of supply ruling on the date the quotation is made and any alterations thereto either before acceptance of or during the currency of the contract shall be to the Buyer’s account. Where no prices have been quoted by the Seller, the price to be charged is that ruling on the date of delivery of the goods. The Seller is at liberty to change its prices without notice to the Buyer.PAYMENT14 The Buyer must pay the net invoice amount together with all Costs to the Seller at its address for payment, without demand, within 30 days after delivery of the goods in respect of which an invoice was raised by the Seller.15 By way of liquidated damages for breach of the payment obligation in these conditions, the Buyer agrees to pay compound interest on the net invoice amount and all Costs calculated from the date of invoice at the rates set from time to time by section 94 of the Supreme Court Act, 1970 plus 1/8th of that rate.16 Where the Buyer pays the purchase price in accordance with these conditions the Seller accepts that sum in full satisfaction of the Buyer’s obligation. The Buyer acknowledges that only payments which reach the Seller at its stated address for payment within the month following the month in which the goods were delivered or such other terms of payment specified in writing by the Seller shall be entitled to receive the benefit of this concession.17 The Buyer agrees to pay the Seller’s legal costs as between solicitor and own client for all legal actions between the Seller and the Buyer in regard to the failure of the Buyer to comply with these conditions.
INCITE FIrE PTy lImITED (aCN 089 243 989)STANDARD TERMS AND CONDITIONS OF SALE
www.incitefire.com.au • For customer service call 1300 INCITE www.incitefire.com.au • For customer service call 1300 INCITE
RIGHTS IN RELATION TO GOODS18 Seller reserves the following rights in relation to the goods until all accounts owed by the Buyer to the Seller are fully paid: 18.1 legal ownership of the goods; 18.2 to enter the Buyer’s premises (or the premises of any associated company or agent where the goods are located) without liability for trespass or any resulting damage and retake possession of the goods irrespective of the manner of their attachment to any realty; and 18.3 to keep or resell any goods repossessed pursuant to (2) above.TITLE TO GOODS19 Property in each unit of the goods shall remain with Seller until all monies owing to Seller on any account whatsoever have been paid (“the Debts”). The Buyer shall in the meantime take custody of the goods and retain them as Seller’s trustee, fiduciary agent and bailee and shall store the goods in such a manner that they are readily distinguishable from other goods owned by the Buyer or other persons (“the Other Goods”). Pending resale or utilisation in any manufacturing or other process, the goods are to be kept separate from the Other Goods and properly marked, stored, protected and insured. 19.1 The Buyer may resell the goods, but only as fiduciary agent and trustee for the Seller, by way of bona fide sale at full market value and in the ordinary course of its business. 19.2 Until the Debts have been paid in full the Buyer shall hold such part of the money it receives from:- 19.2.1 any sub-sale of the goods under the immediately preceding subclause; and 19.2.2 the proceeds of any sale of any products into which the goods have been mixed or converted by any process as equals the amount of the debts at the time the money is received (“the Proceeds”) as bailee and fiduciary agent and trustee for the Seller. 19.3 The Buyer expressly acknowledges that it is bound by such fiduciary obligation and acknowledges that: 19.3.1 it must hold the Proceeds on trust for the Seller. 19.3.2 it must place the whole of the Proceeds in an account separate from its own moneys (“the Proceeds Account”). 19.3.3 it must maintain the Proceeds Account separate from its own moneys at all times. 19.3.4 it must maintain proper records for the Proceeds Account. 19.3.5 it must not assign or encumber the Proceeds or do any other act in derogation of the Seller’s legal or beneficial interests. 19.3.6 it must account to the Seller on demand for all moneys standing to the credit of such account; 19.3.7 the Seller may appropriate payments to such goods and accounts as it thinks fit, notwithstanding any contrary appropriation by the Buyer; 19.3.8 for the purposes of identification of different consignments of goods purchased from Seller and receipt of Proceeds, the Buyer agrees that the principle of “Last In, First Out” shall be applied to any items which cannot be distinguished. 19.3.9 receipt by the Buyer of payment for the sale of any products into which the goods have been mixed or converted by any process shall be treated as evidence that it has received Proceeds; and 19.3.10 the Seller may trace the Proceeds in equity.BUYER’S PROPERTY20 Any property of the Buyer under the Seller’s custody or control shall be entirely at the Buyer’s risk as regards loss or damage caused to the property or by it. The Buyer expressly grants to the Seller such rights of sale as would arise if the Seller had displayed a notice under the Disposal of Uncollected Goods Act, whether or not the Seller had displayed such a notice.STORAGE21 The Seller reserves the right to make a reasonable charge for storage if delivery instructions are not provided by the Buyer within fourteen days after a request by the Seller for such information.GOODS SOLD22 All goods to be supplied by Seller shall be as described on the purchase order agreed by the Seller and the Buyer and the description on such purchase order modified as so agreed shall prevail over all other descriptions including any Buyer’s specification or enquiry. The goods supplied are not designed or adapted for use in adverse industrial atmosphere or weather or abnormal operating conditions of any kind.CANCELLATION23 No order may be cancelled except with consent in writing and on terms which will indemnify the Seller against all losses.PLACE OF CONTRACT24 The contract for the sale of the goods is made in the state inwhich the sale originates and the parties agree to submit all disputes arising between them to the courts of such state at any court competent to hear appeals therefrom.NO WAIVER25 The failure of any party to enforce the provisions of this agreement or to exercise any rights expressed in this agreement shall not be a waiver of such provisions or rights and shall not affect the enforcement of this agreement. The exercise by any party of any of its rights expressed in this agreement shall not preclude or prejudice such party from exercising the same or any other rights it may have irrespective of any previous action taken by that party.FORCE MAJEURE26 Where a party is unable, wholly or in part, by reason of an act of God, strike, lockout or other interference with work, war declared or undeclared, blockade, disturbance, lightning, fire, earthquake, storm, flood, explosion, governmental or quasi-governmental restraint, expropriation prohibition intervention direct or embargo, unavailability or delay in availability of equipment or transport, inability or delay in obtaining governmental or quasi-gover mental approvals consents permits licences authorities or allocations, and any other cause whether of the kind specifically enumerated above or otherwise which is not reasonably within the control of the party affect (`force majeure’), to carry out any obligation under this agreement and that party: 26.1 gives the other party prompt notice of that force majeure with reasonably full particulars thereof, and, insofar as known, the probable extent of which it will be unable to perform or be delayed in performing that obligation; and 26.2 uses all possible diligence to remove that force majeure as quickly as possible; that obligation is suspended so far as it is affected by force majeure during the continuance thereof provided that; 26.3 an obligation to pay money is never excused by force majeure. 26.4 the requirement that any force majeure shall be removed with all possible diligence shall not require the settlement of strikes, lockouts or other labour disputes, or claims or demands by any government on terms contrary to the wishes of the party affected.EXCLUSION OF NEGLIGENCE27 The Seller shall not be liable to the Buyer in contract or in tort arising out of, or in connection with, or relating to, the performance of the goods or any such breach of these conditions or of any fact, matter or thing relating to the goods or error (whether negligent of a breach of contract or not) in information supplied to the Buyer or a user before or after the date of the Buyer’s or user’s use of the goods.SEVERANCE28 If any of the terms or conditions is deemed to be unlawful or unenforceable, such term or condition shall be severed and all other terms and conditions shall remain in force.
INTERPRETATION1 In these conditions: 1.1 ‘Buyer’ means the buyer of any goods including any specified overleaf. 1.2 ‘Conditions’ or ‘these conditions’ means these Terms and Conditions of Sale. 1.3 ‘Costs’ includes Goods and Services Tax (GST) payable as a result of any taxable supply (including the release of any obligation arising under these conditions by the Seller to the Buyer) or as a result of an order made in any proceedings between the Seller and the Buyer. 1.4 ‘Goods’ means any products and services specified including any overleaf. 1.5 ‘Seller’ means INCITE FIRE Pty Limited (ACN 089 243 989) and its assigns or successors and each corporation (within the meaning of that term in Section 9 of the Corporations Law) which now or hereafter is or shall be deemed to be related to the Seller (within the meaning of Section 50 of the Corporations Law). 1.6 Nothing in these conditions shall be read or applied so as to exclude, restrict or modify or have the effect of excluding, restricting or modifying any condition, warranty, guarantee, right or remedy implied by law (including the Trade Practices Act 1974) and which by law cannot be excluded, restricted or modified.GENERAL2 These conditions (which shall only be waived or varied in writing signed by the Seller) shall prevail over all conditions of the Buyer’s order to the extent of any inconsistency.TERMS OF SALE3 The goods and all other products sold by the Seller are sold on these terms and conditions.4 Where any payment from the Buyer to the Seller is overdue the Seller may without notice demand from the Buyer payment of all amounts due for any goods sold by the Seller to the Buyer.SAMPLES, VARIANCES, ETC5 All samples, specifications, drawings, and particulars of dimensions, gauge, shade, colour or quality submitted to the Seller are approximate only and any deviation shall not be taken to vitiate any contract with the Seller or form grounds for any claim against the Seller.DELIVERY 6 Where the Seller arranges delivery it is as agent of the Buyer and at the Buyer’s risk and in that circumstance the sale is to be treated as if it had been made at the Seller’s premises.7 The delivery times made known to the Buyer are estimates only and Seller shall not be liable for to late delivery or non-delivery and under no circumstances shall the Seller be liable for any loss, damage or delay occasioned to the Buyer or its customers arising from late or non-delivery of the goods.LOSS OR DAMAGE IN TRANSIT8 The Seller is not responsible for any loss or damage to goods in transit. SELLER’S LIABILITIES9 The Seller shall not be liable for and the Buyer releases the Seller from any claims in respect of faulty or defective design of any goods supplied unless such design has been wholly prepared by the Seller and the responsibility for any claim has been specifically accepted by the Seller in writing and in any event the Seller’s liability hereunder shall be strictly limited to the replacement of defective goods in accordance with these conditions.10 Except as provided in these conditions, all express and implied warranties, guarantees and conditions under statute or general law as to merchantability, description, quality, suitability or fitness of the goods for any purpose or as to design, assembly, installation, materials or workmanship or otherwise are hereby expressly excluded. The Seller shall not be liable for physical or financial injury, loss or damage or for consequential loss or damage of any kind arising out of the supply, layout, assembly, installation, materials or workmanship or otherwise are hereby expressly excluded and the Seller shall not be liable for physical or financial injury, loss or damage or for consequential loss or damage of any kind arising out of the supply, layout, assembly, installation or operation of the goods or arising out of the Seller’s negligence or in any way whatsoever.11 The Buyer acknowledges its duty to inspect the entire order to ensure its satisfaction with the order.12 The Seller’s liability for a breach of a condition or warranty implied by Division 2 of Pt V of the Trade Practices Act 1974 (other than s 69) is hereby limited to:- 12.1 in the case of goods, any one or more of the following: 12.1.1 the replacement of the goods or the supply of equivalent goods; 12.1.2 the repair of the goods; 12.1.3 the payment of the cost of replacing the goods or of acquiring equivalent goods; 12.1.4 the payment of the cost of having the goods repaired; or 12.2 in the case of services: 12.2.1 the supplying of the services again; or 12.2.2 the payment of the cost of having the services supplied again. 12.3 The Seller’s liability under s 74H of the Trade Practices Act 1975 is expressly limited to a liability to pay to the Buyer an amount equal to: 12.3.1 the cost of replacing the goods; 12.3.2 the cost of obtaining equivalent goods; or 12.3.3 the cost of having the goods repaired, whichever is the lowest amount.PRICES13 Unless otherwise stated all prices quoted by the Seller are exclusive of GST. Prices quoted are those ruling at the date of issue of quotation and are based on rates of freight, insurance, customs duties, currency exchange, shipping expenses, sorting and stacking charges, cartage, rates of weights, cost of materials and other charges affecting the cost of supply ruling on the date the quotation is made and any alterations thereto either before acceptance of or during the currency of the contract shall be to the Buyer’s account. Where no prices have been quoted by the Seller, the price to be charged is that ruling on the date of delivery of the goods. The Seller is at liberty to change its prices without notice to the Buyer.PAYMENT14 The Buyer must pay the net invoice amount together with all Costs to the Seller at its address for payment, without demand, within 30 days after delivery of the goods in respect of which an invoice was raised by the Seller.15 By way of liquidated damages for breach of the payment obligation in these conditions, the Buyer agrees to pay compound interest on the net invoice amount and all Costs calculated from the date of invoice at the rates set from time to time by section 94 of the Supreme Court Act, 1970 plus 1/8th of that rate.16 Where the Buyer pays the purchase price in accordance with these conditions the Seller accepts that sum in full satisfaction of the Buyer’s obligation. The Buyer acknowledges that only payments which reach the Seller at its stated address for payment within the month following the month in which the goods were delivered or such other terms of payment specified in writing by the Seller shall be entitled to receive the benefit of this concession.17 The Buyer agrees to pay the Seller’s legal costs as between solicitor and own client for all legal actions between the Seller and the Buyer in regard to the failure of the Buyer to comply with these conditions.
INCITE FIrE PTy lImITED (aCN 089 243 989)STANDARD TERMS AND CONDITIONS OF SALE
www.incitefire.com.au • For customer service call 1300 INCITE
Catalogue Disclaimer1.1 The information contained in this catalogue is obtained from the various manufacturers of the products. We are merely passing the information to you.
We do not guarantee that the information is correct. Prior to making a decision to purchase you should confirm the details of the product with an
alternative source directly.
1.2 Product descriptions and specifications are subject to change at any time, without notice.
1.3 We do not guarantee that any particular product will be available for sale. The availability for sale of the products described in this catalogue depends on
the manufacturer and is beyond our control. This catalogue is not an offer of sale.
Usual Terms of Sale2.1 All product sales are subject to our usual terms of sale as varied from time to time. Our current usual terms of sale are included in this catalogue.
2.2 Please note that usual terms of sale are subject to change at any time.
vesda®
www.incitefire.com.au • For customer service call 1300 INCITE www.incitefire.com.au • For customer service call 1300 INCITE
Incite Fire Pty Ltd is a fully independent fire alarm systems product wholesaler, Sydney & Melbourne based, established in 1999.
Our Objective“Quality fire detection and warning equipment,
independently supplied & supported”
inside Our catalOgue
Conventional Fire Detection We stock the complete range of current & past model Hochiki detectors, as well as a
selection of conventional panels which can be customised to suit your requirements.
Analogue / Addressable Fire Detection Incite Fire is the NSW & ACT distributor of the FireNet analogue panel. We also stock the complete range of Hochiki addressable detectors & field modules.
VESDA Incite Fire is an authorised distributor for the complete range of VESDA aspirated detectors as well as pipework & fittings. Spare parts are available & we can also arrange for the repair of all current model detectors.
Warning Systems A range of OWS and accessories to suit your requirements, as well as EWIS panels configurable to suit any site specifications.
Ancillary Equipment A comprehensive range of ancillary devices including KAC manual call points, a selection of speakers, sounders & strobes. We also stock a range of magnetic door retainers to suit many different applications including the new brass & chrome finish door holders for a more prestigious application.
Special Applications A selection of detection equipment for special applications including flame detectors, firewire, VESDA. Also available is intrinsically safe equipment & detectors suitable for marine applications.
Miscellaneous For convenience we also stock a selection of tools, fixings, enclosures & cable.
Distributors in NSW/ACT and VIC for: • FireNet - Analogue/Addressable Fire Alarm Control Panel • Hochiki - Detectors Analogue & Conventional • VESDA - Range of Aspirated Detectors • Simplex - Evacuation & Warning Systems
For further informationCall: 1300 INCITE (462483)Or visit us at: www.incitefire.com.au
Ne
w C
on
ven
tion
al D
ete
cto
rssl
v-a
s –
Pho
to e
lec
tric
dC
d-a
– T
ype
A t
he
rma
ld
FJ-6
0B –
Typ
e B
th
erm
al
dC
d-C
– T
ype
C t
he
rma
lD
FJ-9
0D –
Typ
e D
th
erm
al
sIJ-
asN
– Io
niz
atio
n
Pre
vio
us
Co
nve
ntio
na
l De
t.SL
K-A
S –
Pho
to e
lec
tric
dC
C-a
– T
ype
A t
he
rma
ld
FE-6
0B –
Typ
e B
th
erm
al
dC
C-C
– T
ype
C t
he
rma
lD
FE-9
0D –
Typ
e D
th
erm
al
SIH
-AM
– Io
niz
atio
n
Ne
w A
na
log
ue
De
tec
tors
alg
-as
– Ph
oto
ele
ctr
ica
Tg-a
s –
The
rma
la
IE-a
s –
Ion
iza
tion
aC
a-E
– M
ulti
Se
nso
ra
CB-
as
– M
ulti
th
erm
al
Pre
vio
us
An
alo
gu
e D
ete
cto
rsa
lB-E
– P
ho
to e
lec
tric
aIa
-E –
Ion
iza
tion
aTa
-E –
The
rma
l
Ne
wC
on
ve
nti
on
al
Ba
ses
YB
o-R
/4a
Pre
vio
us
Co
nv
en
tio
na
lB
ase
s
YB
C-R
/3a
YB
F-R
L/4
AH
AM
Ne
wA
dd
ress
ab
leB
ase
s
YC
A-R
L/3
H2
MY
CA
-RL/
5H
2M
Pre
vio
us
Ad
dre
ssa
ble
Ba
ses
aM
u-B
2M
aM
u-M
BM
YB
F-R
l/3
JM
Ne
wA
na
log
ue
Ba
ses
YB
N-R
/2N
aY
Bo
-R/s
CI
Pre
vio
us
An
alo
gu
eB
ase
s
YB
F-R
l/2
NB
F
HOcHiki detectOr & base cOmpatibility cHart
1300 INCITE
CaTaloguE v.02
“Quality fire detection and warning equipment,independently supplied and supported”
www.incitefire.com.au • For customer service call 1300 INCITE
CoNTaCT dETaIlsNsW/aCT3/165 Rookwood RoadYagoona NSW 2199Tel: 1300 INCITEFax: 02 9707 1900
vICAxxess Corporate Park120/45 Gilby RoadMount Waverley VICTel: 1300 INCITE