Upload
salman-habba
View
213
Download
0
Embed Size (px)
Citation preview
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 1/60
CHAPTER 1
(week 1-3)Strain Analysis
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 2/60
• Some common engineering problems such as adam subjected to water loading, a tunnel underexternal pressure, a pipe under internalpressure, and a cylindrical roller bearingcompressed by force in a diametral plane, havesignificant strain only in a plane; that is, thestrain in one direction is much less than thestrain in the two other orthogonal directions. Ifsmall enough, the smallest strain can be ignoredand the part is said to experience plane strain.
• Assume that the negligible strain is oriented in the z -direction. To reduce the 3D strain matrix to the 2D plane stress matrix, remove allcomponents with z subscripts.
Plain Strain
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 3/60
Plain Strain
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 4/60
GENERAL EQUATION OF PLANE STRAINTRANSFORMATION
Normal strain ex and e y arepositive if cause elongationalong x and y axis
Shear strain gxy is positive
if the interior angle AOBbecome smaller than 900. q0 will be positive using the
right-hand fingers.i.e counterclockwise
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 5/60
Normal and Shear Strains
• In Fig a :
• Positive ex occurline d
x elongated e
xd x , which causeline dx’ toelongated ex d x cos
q.
q
q
sin
cos
'
'
dxdy
dxdx
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 6/60
• Positive e y occur line d y elongated e y d y , which
cause line d y ’ to elongatede yd y sin q.
• Assuming dx fix inposition.
• Shear strain g xy changesin angle between dx anddy. dy displaced g xy dy tothe right.
• Dx’ elon ate d cos q
Normal and Shear Strains (cont.)
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 7/60
• Adding all the elongations
qqgqeqee
qqgqqeqqee
e
cossinsincos
dx
cos)sindx(sin)sindx(cos)cosdx(
dx
x
xy
2
y
2
xx
'
'
xy
'
y
'
x
x
'
'
x
'
'
'
qgqeqe cosdysindycosdxxyyxx '
Normal and Shear Strains (cont.)
q q
sincos
'
'
dxdydxdx
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 8/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 9/60
Normal and Shear Strains (cont.)
qg
qee
ee
e 2sin2
2cos22
xyyxyx
x '
qg
qee
ee
e 2sin2
2cos22
xyyxyx
y '
Using trigonometric identities:
qg
q
ee
g2cos
22sin
22
xyyxyx ''
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 10/60
• Principal Strains
• Direction axis of principlestrain:
• Max in Plane shear strain
• Ave shear strain
• Direction axis of shearstrain
2
xy
2
yx planeinmax,
222
g
eeg
2
yx
ave
eee
)(2tan
yx
xy
p ee
gq
g
eeq
xy
yx
s2tan
2
xy
2
yxyx
2,1222
g
ee
eee
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 11/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 12/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 13/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 14/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 15/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 16/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 17/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 18/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 19/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 20/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 21/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 22/60
Construction of the Mohr’s Circle
PROCEDURE FOR ANALYSIS
The procedure for drawing Mohr's circle for strainfollows the one established for stress.Construction of the Circle.• Establish a coordinate system such that the
abscissa represents the normal strain e, withpositive to the right, and the ordinate represents
half the value of the shear strain, g/2, with positivedownward .
• Using the positive sign convention for ex, e y, gxy asshown in the Fig. , determine the center of the circleC, which is located on the e axis at a distancee avg= (e x + e y)/2 from the origin.
• Plot the reference point A having coordinatesA(e x, g xy/2). This point represents the case forwhich the x' axis coincides with the x axis. Henceq = q.
• Connect point A with the center C of the circle andfrom the shaded triangle determine the radius R ofthe circle.
• Once R has been determined, sketch the circle.
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 23/60
• The principal strains e1 and e2 are determinedfrom the circle as the coordinates of points Band D, that is where g/2 = 0, Fig. a.
• The orientation of the plane on which e1 acts canbe determined from the circle by calculating 2qP1,using trigonometry. Here this angle is measuredcounterclockwise from the radial reference lineCA to line CB, Fig. a. Remember that the rotationof qP1 must be in this same direction, from the
element's reference axis x to the x' axis, Fig. b.*
• When e1 and e2 are indicated as being positive asin Fig. a, the element in Fig. b will elongate in thex' and y' directions as shown by the dashedoutline.
Principal Strain
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 24/60
• The average normal strain and half themaximum in-plane shear strain are determinedfrom the circle as the coordinates of points Eand F, Fig. a.
• The orientation of the plane on which gmax in plane and eavg act can be determined from the circleby calculating 2qs1, using trigonometry. Herethis angle is measured clockwise from the radialreference line CA to line CE, Fig. a. Rememberthat the rotation of qs1, must be in this same
direction, from the element's reference axis xto the x' axis, Fig. c.
Maximum In Plane Shear Strain
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 25/60
• The normal and shear strain components ex’, and
g x’y’ for a plane specified at an angle q, Fig. d, canbe obtained from the circle using trigonometry todetermine the coordinates of point P, Fig.a.
• To locate P, the known angle q of the x' axis ismeasured on the circle as 2q. This measurement ismade from the radial reference line CA to the
radial line CP. Remember that measurements for2q on the circle must be in the same direction as q for the x' axis!
• If the value of e y, is required, it can bedetermined by calculating the e coordinate ofpoint Q in Fig. a. The line CQ lies 180o away from
CP and thus represents a rotation of 900
of the x'axis.
Strains on Arbitrary Plane
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 26/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 27/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 28/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 29/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 30/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 31/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 32/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 33/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 34/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 35/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 36/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 37/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 38/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 39/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 40/60
Strain Rosettes
• The axes of the threegauges are arranged at theangles of qa, qb, qc.
• If the reading of ea, eb, ec
taken, ex, e y, gxy can bedefined.
• Value of ex, e y, gxy aredetermined by solvingthese equations.
ccxyc
2
yc
2
xc
b bxy b
2
y b
2
x b
aaxya
2
ya
2
xa
cossinsincos
cossinsincos
cossinsincos
qqgqeqee
qqgqeqee
qqgqeqee
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 41/60
45o or Rectangular Rosette
0
0
0
90
45
0
c
b
a
q
q
q
The equation become:
ca bxy
cy
ax
2 eeeg
ee
ee
Example of 45o strain rosette
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 42/60
600 Strain Rosette
c bxy
ac by
ax
3
2
223
1
eeg
eeee
ee
0
c
0
b
0
a
120
60
0
q
q
q
The equation become:
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 43/60
Example
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 44/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 45/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 46/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 47/60
Stress Strain Relationship
• If a material subject to triaxial
stress (sx, s y, sz), associatednormal stress(ex, e y, ez)developed in the material.
• When sx is applied in x-direction, the element elongated with e
x
in x direction.
• Application on s y cause theelement to contract with astrain e” x in the x direction.
• Application Of sz cause the
element to contract with astrain e’’’ x in the x direction.
z x
y x
x x
s
e
s
e
s
e
'''
''
'
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 48/60
• The same result can bedeveloped for the normalstrain in the y and zdirection.
• Final results can bewritten as…..
yxzz
zxyy
zyxx
1
1
1
sss
e
sss
e
sss
e
Stress Strain Relationship (cont.)
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 49/60
Applying only shear stress, y to the element.
If to apply shear stress,t y to the element. txy will only cause deformation to gxy.
txy will not cause deformation to g yz.and gxz
t yz and t xz will only cause deformation to
g yz and gxz respectively. Hooke Law for shear stress and shear
strain written as:
xz xz
yz yz
xy xy
G
G
G
t g
t g
t g
1
1
1
Element subjected to normalstresses only
Shear stress applied to theelements
Stress Strain Relationship (cont.)
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 50/60
• Modulus of elasticity, E isrelated to shear modulus, G.
• Dilatation (the change in
volume per unit volume or‘volumetric strain’, e .
• Bulk Modulus (volumemodulus of elasticity), k .
12
E G
zyxE21 sssue
Stress Strain Relationship (cont.)
213
E
k
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 51/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 52/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 53/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 54/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 55/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 56/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 57/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 58/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 59/60
8/21/2019 1.0 Strain Analysis
http://slidepdf.com/reader/full/10-strain-analysis 60/60