WASTE WATER MANAGEMENT & GROUND CONTAMINATION PREVENTION
IntroducingSVS Solutions Inc.The main target of SVS Solutions
products will be drilling programs that require specialized fluid
system requirements. The heating of mud systems on-site and
evaporation of waste fluids on-site. Environmental concerns often
arise due to the service and drilling rigs remaining immobile for
longer periods of time as disposable fluids collect on-site.If left
unattended this can result in very large and very costly clean-up
costs at the end of a project, here with SVS we hope to virtually
eliminate these associated types of costs, clean-ups and/or
concerns.
The main target of SVS Solutions products will be drilling
programs that require specialized fluid system requirements. The
heating of mud systems on-site and evaporation of waste fluids
on-site. Environmental concerns often arise due to the service and
drilling rigs remaining immobile for longer periods of time as
disposable fluids collect on-site.If left unattended this can
result in very large and very costly clean-up costs at the end of a
project, here with SVS we hope to virtually eliminate these
associated types of costs, clean-ups and/or concerns. 1
Induction Power source
FLAMLESS, water or glycol cooled induction heating is designed
for heating fluids up to 1450 Fahrenheit (788 C)
LEDs indicate units for temperature measurements. Uniform
heating is maintained along and through the heat chambers zone by
using induction. Time-to-temperature is faster than conventional
processes due to the method of applying the heat, reducing heating
cycle time. Rated output is 35 kW at 100% duty cycle, 5 30 KHz High
energy-efficient systems transfers more energy to the heat
chambers, decreasing heating times and improving power efficiency.
The pro-heat 35 induction power source is equipped with a built-in
temperature controller. The controller is designed to be easily
understood and programmed. Multiple control thermocouple inputs are
installed on the heating chambers for uniform heating and quality.
The pro-heat 35 induction power source is designed with two output
connectors for liquid-cooled cables. The liquid-cooled heating
cable couples the power to the heating chamber to be heated. The
silicone hose encloses a special copper conductor specifically
designed for carrying high-frequency currents to maximize
efficiency. The hose also carries the coolant, which cools the
conducting wire and the outside temperature to maximum 22 C. The
induction procedure for evaporating or heating is not power with an
open flame fire system.
LEDs indicate units for temperature measurements. Uniform
heating is maintained along and through the heat chambers zone by
using induction. Time-to-temperature is faster than conventional
processes due to the method of applying the heat, reducing heating
cycle time. Rated output is 35 kW at 100% duty cycle, 5 30 KHz High
energy-efficient systems transfers more energy to the heat
chambers, decreasing heating times and improving power efficiency.
The pro-heat 35 induction power source is equipped with a built-in
temperature controller. The controller is designed to be easily
understood and programmed. Multiple control thermocouple inputs are
installed on the heating chambers for uniform heating and quality.
The pro-heat 35 induction power source is designed with two output
connectors for liquid-cooled cables. The liquid-cooled heating
cable couples the power to the heating chamber to be heated. The
silicone hose encloses a special copper conductor specifically
designed for carrying high-frequency currents to maximize
efficiency. The hose also carries the coolant, which cools the
conducting wire and the outside temperature to maximum 22 C. The
induction procedure for evaporating or heating is not power with an
open flame fire system.2
Heat Induction Video PresentationWe have features for every step
of the way 1Author YourPresentation 2Enrich YourPresentation 3Share
YourPresentation
The above video presentation focuses mainly on the induction
heating and has a small breakdown of an operational unit heating
30m3 of fresh water in a 400bbl upright tank. Additional equipment
for waste fluid management & ground contamination prevention
available upon request. Broke down & summarized in following
power point presentation is some of the key points to this
equipment.
The above video presentation focuses mainly on the induction
heating and has a small breakdown of an operational unit heating
30m3 of fresh water in a 400bbl upright tank. Additional equipment
for waste fluid management & ground contamination prevention
available upon request. Broke down & summarized in following
power point presentation is some of the key points to this
equipment. 3
Kook Kettle Tank and ExhaustThe same tank is used for
evaporating or heating operations. The tank has a capacity of
1.75m3. The tank is wrapped with 50mm insulation and covered with
12.7mm puck board. The outer tank temperate will not exceed more
the 22 C. There is a 50mm screened suction inlet and a 50mm suction
outlet that is used for circulating fluids through the induction
heating chambers. Fluids from the induction heating chambers may be
circulated back into the kook kettle for evaporating operations or
into surface tanks for heating operations. Fluids from the kook
kettle may be circulated at 20 liters to 162 liters per minute. The
exhaust system is used only in the evaporating operation, fluids
are circulated though the exhaust. The exhaust is a mist free
component. Closing exhaust lunges are required for changing from
evaporating to heating operations.
The same tank is used for evaporating or heating operations. The
tank has a capacity of 1.75m3. The tank is wrapped with 50mm
insulation and covered with 12.7mm puck board. The outer tank
temperate will not exceed more the 22 C. There is a 50mm screened
suction inlet and a 50mm suction outlet that is used for
circulating fluids through the induction heating chambers. Fluids
from the induction heating chambers may be circulated back into the
kook kettle for evaporating operations or into surface tanks for
heating operations. Fluids from the kook kettle may be circulated
at 20 liters to 162 liters per minute. The exhaust system is used
only in the evaporating operation, fluids are circulated though the
exhaust. The exhaust is a mist free component. Closing exhaust
lunges are required for changing from evaporating to heating
operations.
4
Chamber Pipe and CarrierThe 152mm x 1.93m chamber pipe is
wrapped with an insulated blank and the induction liquid-cooled
heating cables. There is an inner and outer chamber. Fluids are
circulated through both inner and outer chambers. Heat is
controlled from the pre-set temperature control on the induction
machine.
Chamber Pipe and CarrierThe 152mm x 1.93m chamber pipe is
wrapped with an insulated blank and the induction liquid-cooled
heating cables. There is an inner and outer chamber. Fluids are
circulated through both inner and outer chambers. Heat is
controlled from the pre-set temperature control on the induction
machine.
5
The chambers are mounted in a carrier. This allows for easy
access for servicing liquid-cooled heating cables or fluid systems.
The pro-heat 35 induction power source is designed with two output
connectors for liquid-cooled cables. There are two chambers
operational with one induction machine.
The chambers are mounted in a carrier. This allows for easy
access for servicing liquid-cooled heating cables or fluid systems.
The pro-heat 35 induction power source is designed with two output
connectors for liquid-cooled cables. There are two chambers
operational with one induction machine.
6
Kettle TankThe same tank is used for evaporating or heating
operations. The tank has a capacity of 8.60m3. The tank is wrapped
with 50mm insulation and is covered with 12.7mm puck board. The
outer tank temperature will not exceed more than 22 C. The kettle
tank meets all safety regulations that are required by the oil and
gas industry, double walled "cool to the touch" tank design and a
host of other details that ensure personal safety for operators.
The tank is fitted with a compartment that allows the rigs boiler
to be blown down directly into the tank. The kettle tank is fitted
with a fluid pump that has a capacity of circulating 162 liters per
minute.
The same tank is used for evaporating or heating operations. The
tank has a capacity of 8.60m3. The tank is wrapped with 50mm
insulation and is covered with 12.7mm puck board. The outer tank
temperature will not exceed more than 22 C. The kettle tank meets
all safety regulations that are required by the oil and gas
industry, double walled "cool to the touch" tank design and a host
of other details that ensure personal safety for operators. The
tank is fitted with a compartment that allows the rigs boiler to be
blown down directly into the tank. The kettle tank is fitted with a
fluid pump that has a capacity of circulating 162 liters per
minute.
7
Plug In Induction Heating UnitThe induction heating system can
heat while circulating invert tank farms, 60m3 and 100m3 upright
tanks and surface holding tanks. The power supply needed for the
unit is one 60 Amp 480 Volt plug-in. Maximum power required for
operations is 34 kW / 40 Amps which would be supplied from the rig
or a rental generator, or could be wired directly from the main
power grid. The 1.75m3 kook kettle tank two heating chambers
mounted in a carrier and one induction unit are mounted in 3.0m
container. There is 1.75m3 Capacity for glycol for circulating
tanks, all insulated lines can be sucked back to the tank with the
same circulating pump. Fluid circulating temperature is controlled
on the induction machine. There is a hydraulic operated light tower
mounted on the unit. The container is 2.44m wide, 2.70m height and
3.0m long, total weight is 2,610 kgs.
Plug In Induction Heating UnitThe induction heating system can
heat while circulating invert tank farms, 60m3 and 100m3 upright
tanks and surface holding tanks. The power supply needed for the
unit is one 60 Amp 480 Volt plug-in. Maximum power required for
operations is 34 kW / 40 Amps which would be supplied from the rig
or a rental generator, or could be wired directly from the main
power grid. The 1.75m3 kook kettle tank two heating chambers
mounted in a carrier and one induction unit are mounted in 3.0m
container. There is 1.75m3 Capacity for glycol for circulating
tanks, all insulated lines can be sucked back to the tank with the
same circulating pump. Fluid circulating temperature is controlled
on the induction machine. There is a hydraulic operated light tower
mounted on the unit. The container is 2.44m wide, 2.70m height and
3.0m long, total weight is 2,610 kgs.
8
Plug In Induction Evaporator/Heating UnitThe Induction
Evaporator System can process 8m3 of fluid evaporation per day. The
power supply needed for the unit is one 100 Amp 480 Volt plug-in.
Maximum power required for operations is 68 kW / 77 Amps which
would be supplied from the rig or a rental generator, or could be
wired directly from the main power grid. The 1.75m3 kook kettle
tank four heating chambers mounted in a carrier and two induction
units are mounted in 6.0m container. The induction units are
computer controlled for setting a required temperature. The feed
pump is also computer controlled for setting the required flow.
There is an 8.6m3 kettle tank mounted on the skid. A complete field
services and inspection conducted takes four hours. The skid is
2.44m wide, 2.70m height and 9.14m long, total weight is 8,180
kgs.
Plug In Induction Evaporator/Heating UnitThe Induction
Evaporator System can process 8m3 of fluid evaporation per day. The
power supply needed for the unit is one 100 Amp 480 Volt plug-in.
Maximum power required for operations is 68 kW / 77 Amps which
would be supplied from the rig or a rental generator, or could be
wired directly from the main power grid. The 1.75m3 kook kettle
tank four heating chambers mounted in a carrier and two induction
units are mounted in 6.0m container. The induction units are
computer controlled for setting a required temperature. The feed
pump is also computer controlled for setting the required flow.
There is an 8.6m3 kettle tank mounted on the skid. A complete field
services and inspection conducted takes four hours. The skid is
2.44m wide, 2.70m height and 9.14m long, total weight is 8,180
kgs.
9
Stand Alone Evaporator/Heating UnitThe standalone
evaporator/heating unit can process 10 - 16m3 of fluid evaporation
per day. The well thought out layout ensures the entire system is
simple to move, set up and operate. The power source is a 9/litre
400 Amp Cat diesel generator mounted in a 6.0m container on the
Skid. The power supplied from the Skid is sufficient to operate
invert tank farms, centrifuges and transfer pumps. There is a 6600
liter fuel tank mounted on the skid. With the generator working at
25% to 80% of usage the fuel used is 21 litres to 44 litres per
hour. There is an 8.6m3 kettle tank mounted on the skid.
Stand Alone Evaporator/Heating UnitThe standalone
evaporator/heating unit can process 10 - 16m3 of fluid evaporation
per day. The well thought out layout ensures the entire system is
simple to move, set up and operate. The power source is a 9/litre
400 Amp Cat diesel generator mounted in a 6.0m container on the
Skid. The power supplied from the Skid is sufficient to operate
invert tank farms, centrifuges and transfer pumps. There is a 6600
liter fuel tank mounted on the skid. With the generator working at
25% to 80% of usage the fuel used is 21 litres to 44 litres per
hour. There is an 8.6m3 kettle tank mounted on the skid.
10
An induction system is mounted on the kettle tank. The generator
is fitted with an Exhaust Emission system. The Exhaust Emission
system is capable of 12m3 evaporation daily and the induction
system would allow for another 6m3 evaporation daily. Total 18m3
evaporation rate daily. This would only require 22% of the
generators power, which allows for 270 amps of power to be used for
operating additional equipment that the rig would be using. This
skid may also be used for heating and circulating heated water to a
60m3 and 100m3 upright tanks, frac ponds and surface holding tanks.
The skid is 2.44m wide, 2.70m height and 12.1m long. Total weight
is 14,545 kgs.
An induction system is mounted on the kettle tank. The generator
is fitted with an Exhaust Emission system. The Exhaust Emission
system is capable of 12m3 evaporation daily and the induction
system would allow for another 6m3 evaporation daily. Total 18m3
evaporation rate daily. This would only require 22% of the
generators power, which allows for 270 amps of power to be used for
operating additional equipment that the rig would be using. This
skid may also be used for heating and circulating heated water to a
60m3 and 100m3 upright tanks, frac ponds and surface holding tanks.
The skid is 2.44m wide, 2.70m height and 12.1m long. Total weight
is 14,545 kgs.
11
Washer and DryerThe waste water from the industrial washer and
dryer installed in a container also goes directly into the kettle
tank. There is a 540 litre water tank for operating a washing
machine.
.
Washer and DryerThe waste water from the industrial washer and
dryer installed in a container also goes directly into the kettle
tank. There is a 540 litre water tank for operating a washing
machine.
12
Sealer SystemsSVS Solutions has developed a unique system that
does not have any ground disturbance at all, but uses a man-made
trenching system to direct waste fluid to catch cans located in low
spots on the well site location. All catch cans are 100% contained
from the soil. Plastic or a liner is laid prior to spotting the rig
matting. The entire Sealer System can be set up in 4 to 6 hours
with minimal labour and no wait time while the rig is being moved
and rigged up. Once the catch cans are full, a rig hand then uses a
50mm transfer pump provided by SVS Solutions to move the fluid to
the Kettle Tank.
Sealer SystemsSVS Solutions has developed a unique system that
does not have any ground disturbance at all, but uses a man-made
trenching system to direct waste fluid to catch cans located in low
spots on the well site location. All catch cans are 100% contained
from the soil. Plastic or a liner is laid prior to spotting the rig
matting. The entire Sealer System can be set up in 4 to 6 hours
with minimal labour and no wait time while the rig is being moved
and rigged up. Once the catch cans are full, a rig hand then uses a
50mm transfer pump provided by SVS Solutions to move the fluid to
the Kettle Tank.
13
Benefits:Tank is fully automatic "one button push start &
"auto shut off controls. Multiple uses such as boiler blow down,
grey water and ditch water evaporation, reduced hauling charges,
reduced disposal costs. Large safety benefits such as insulated
Kettle Tank is cool to the touch, grilled tank covers keep workers
away from hot water during operation, the tied in Boiler blow down
address all safety for doing daily maintenance of the rig boiler,
reduced risk of "lost time accidents and injuries as travel time
for fluid hauling trucks is significantly decreased, Kettle Tank
prevents potentially dangerous blast of steam when blowing down the
rig boiler again no open flame fire system. Casing displacement
water may also be evaporated off. All units used to-date are
powered with a diesel open flame fire system for evaporating or
heating operations. The advantage that SVS Solutions has to offer
is that we are the only company offering complete well site
collection and disposal of excess fluids. We offer a service that
is unmatched for environmental care and soil contaminant
prevention. No other company offers the secondary system that
collects and directs the fluid to the appropriate locations on the
well site like SVS Solutions.
Benefits:Tank is fully automatic "one button push start &
"auto shut off controls. Multiple uses such as boiler blow down,
grey water and ditch water evaporation, reduced hauling charges,
reduced disposal costs. Large safety benefits such as insulated
Kettle Tank is cool to the touch, grilled tank covers keep workers
away from hot water during operation, the tied in Boiler blow down
address all safety for doing daily maintenance of the rig boiler,
reduced risk of "lost time accidents and injuries as travel time
for fluid hauling trucks is significantly decreased, Kettle Tank
prevents potentially dangerous blast of steam when blowing down the
rig boiler again no open flame fire system. Casing displacement
water may also be evaporated off. All units used to-date are
powered with a diesel open flame fire system for evaporating or
heating operations. The advantage that SVS Solutions has to offer
is that we are the only company offering complete well site
collection and disposal of excess fluids. We offer a service that
is unmatched for environmental care and soil contaminant
prevention. No other company offers the secondary system that
collects and directs the fluid to the appropriate locations on the
well site like SVS Solutions.
14
RadioactiveImagine DragonsImagine DragonsDan Reynolds, Wayne
Sermon, Ben McKee, Alex Da Kid & Josh MosserNight
Visions2012-09-04T07:00:00Z2013-03-04 22:30:39Night Visions
