1
ENGINE
MODEL CUMMINS QSB6.7
TypeWater cooled, 4 cycle Diesel, 6-Cylindersin line, direct injection, turbocharged,charged air cooled and low emission
Rated flywheel horse power
SAEJ1995 (gross) 167 HP (124 kW) / 1,950 rpm
J1349 (net) 157 HP (117 kW) / 1,950 rpm
DIN6271/1 (gross) 169 PS (124 kW) / 1,950 rpm
6271/1 (net) 159 PS (117 kW) / 1,950 rpm
Max. torque 74.7 kgf.m (540 lbf.ft) / 1,500 rpm
Bore x stroke 107 mm x 124 mm (4.2” x 4.9”)
Piston displacement 6,700 cc (409 in3)
Batteries 2 x 12 V x 100 AH
Starting motor 24 V; 4.8 kW
Alternator 24 V, 95 Amp
* This engine meets the EPA (Tier 4 interim) / EU (Stage III-B) Emission regulation.
HYDRAULIC SYSTEM
MAIN PUMPType Two variable displacement axial piston pumps
Max. flow 2 x 228.2 ℓ/min (60.3 US gpm/50.2 UK gpm)
Sub-pump for pilot circuit Gear pump
Cross-sensing and fuel saving pump system
HYDRAULIC MOTORS
TravelTwo-speed axial piston motorwith brake valve and parking brake
Swing Axial piston motor with automatic brake
RELIEF VALVE SETTINGImplement circuits 350 kgf/cm2 (4,978 psi)
Travel 350 kgf/cm2 (4,978 psi)
Power boost (boom, arm, bucket) 380 kgf/cm2 (5,404 psi)
Swing circuit 265 kgf/cm2 (3,769 psi)
Pilot circuit 40 kgf/cm2 (568 psi)
Service valve Installed
HYDRAULIC CYLINDERS
No. of cylinder- bore x stroke
Boom: 2-120 x 1,290 mm (4.7” x 50.8”)
Arm: 1-140 x 1,510 mm (5.5” x 59.4”)
Bucket: 1-120 x 1,055 mm (4.7” x 41.5”)
DRIVES & BRAKES
Drive method Fully hydrostatic type
Drive motor Axial piston motor, in-shoe design
Reduction system Planetary reduction gear
Max. drawbar pull 21,100 kgf (46,500 lbf )
Max. travel speed (high) / (low) 5.7 km/h (3.5 mph) / 3.6 km/h (2.2 mph)
Gradeability 35° (70 %)
Parking brake Multi wet disc
CONTROLPilot pressure operated joysticks and pedals with detachable lever provide almost effortless and fatigueless operation.
Pilot controlTwo joysticks with one safety lever (LH): Swing and arm(RH): Boom and bucket (ISO)
Traveling and steering Two levers with pedals
Engine throttle Electric, Dial type
SWING SYSTEM
Swing motor Fixed displacement axial piston motor
Swing reduction Planetary gear reduction
Swing bearing lubrication Grease-bathed
Swing brake Multi wet disc
Swing speed 10.7 rpm
COOLANT & LUBRICANT CAPACITY
Refilling liter US gal UK gal
Fuel tank 400 105.7 88.0
Engine coolant 35 9.2 7.7
Engine oil 23.7 6.3 5.2
Swing device 6 1.6 1.3
Final drive (each) 6 1.6 1.3
Hydraulic system (including tank) 275 72.6 60.5
Hydraulic tank 160 42.3 35.2
UNDERCARRIAGEThe X-leg type center frame is integrally welded with reinforced box-section trackframes. The undercarriage includes lubricated rollers, idlers, track adjusters with shockabsorbing springs and sprockets, and a track chain with double or triple grouser shoes.
Center frame X - leg type
Track frame Pentagonal box type
No. of shoes on each side 49
No. of carrier rollers on each side 2
No. of track rollers on each side 9
No. of rail guards on each side 2
OPERATING WEIGHT (APPROXIMATE)Operating weight, including 5,680 mm (18’ 8”) boom, 2,920 mm (9’ 7”) arm, SAE heaped 0.92 m3 (1.20 yd3) bucket, lubricant, coolant, full fuel tank, full hydraulic tank and all standard equipments.
MAJOR COMPONENT WEIGHTUpperstructure 5,600 kg (12,350 lb)
Boom (with arm cylinder) 1,950 kg (4,300 lb)
Arm (with bucket cylinder) 1,095 kg (2,410 lb)
OPERATING WEIGHTShoes Operating weight Ground pressure
Type Width mm (in) kg (lb) kgf/cm2 (psi)
Triplegrouser
500 (20”)R220NLC-9A 22,000 (48,500) 0.55 (7.82)
R220NLC-9A 2pc 22,480 (49,560) 0.56 (7.97)
600 (24”)
R220LC-9A 21,900 (48,280) 0.46 (6.54)
R220NLC-9A 22,350 (49,280) 0.47 (6.68)
R220NLC-9A 2pc 22,830 (50,330) 0.48 (6.83)
R220LC-9A H/W 23,360 (51,500) 0.50 (7.11)
R220LC-9A LR 24,360 (53,700) 0.51 (7.25)
700 (28”)
R220LC-9A 22,250 (49,050) 0.40 (5.69)
R220NLC-9A 22,700 (50,050) 0.41 (5.83)
R220NLC-9A 2pc 23,180 (51,100) 0.42 (5.98)
R220LC-9A H/W 23,710 (52,270) 0.43 (6.11)
R220LC-9A LR 24,710 (54,500) 0.45 (6.40)
800 (32”)
R220LC-9A 22,515 (49,640) 0.36 (5.12)
R220LC-9A H/W 23,975 (52,860) 0.38 (5.40)
R220LC-9A LR 24,975 (55,050) 0.40 (5.69)
900 (36”) R220LC-9A 22,760 (50,180) 0.32 (4.55)
R220LC-9A LR 25,220 (55,600) 0.36 (5.12)
Double grouser 700 (28”) R220LC-9A H/W 24,135 (53,210) 0.43 (6.11)
Specifications R220LC-9A / R220NLC-9A
2
BUCKETS R220LC-9A / R220LC-9A LR / R220LC-9A H/WAll buckets are welded with high-strength steel.
SAE heaped m3 (yd3)
ATTACHMENT R220LC-9A / R220LC-9A LR / R220LC-9A H/WBooms and arms are welded, a low-stress, full-box section design. 5.68 m (18’ 8”) & 8.2 m (26’ 11”) Booms and 2.0 m (6’ 7”); 2.4 m (7’ 10”); 2.92 m (9’ 7”); 3.9 m (12’ 10”) & 6.3 m (20’ 8”) Arms are available.
Note: Boom weight includes arm cylinder, piping and pin. Arm weight includes bucket cylinder, linkage and pin.
DIGGING FORCE R220LC-9A / R220LC-9A LR / R220LC-9A H/W
Capacity m3 (yd3)
SAE heaped CECE heaped
Width mm (in)
Without side cutters
With side cutters
Weight kg (lb)
Recommendation m (ft.in)
5.68 (18’ 8”) Boom
Heavy-duty bucket
Heavy duty Rock-bucket
Slope finishing bucket
Long reach bucket
Applicable for materials with density of 2,000 kg/m3 (3,370 lb/yd3) or less
Applicable for materials with density of 1,600 kg/m3 (2,700 lb/yd3) or less
Applicable for materials with density of 1,100 kg/m3 (1,850 lb/yd3) or less
0.51 (0.67)
0.80 (1.05)
0.92 (1.20)
1.10 (1.44)
1.20 (1.57)
1.34 (1.75)
0.74 (0.97)
0.90 (1.18)
1.05 (1.37)
0.87 (1.14)
1.20 (1.57)
0.75 (0.98)
0.52 (0.68)
0.45 (0.59)
0.70 (0.92)
0.80 (1.05)
0.96 (1.26)
1.00 (1.31)
1.15 (1.50)
0.65 (0.85)
0.80 (1.05)
0.92 (1.20)
0.75 (0.98)
1.00 (1.31)
0.65 (0.85)
0.45 (0.59)
700 (27.6)
1,000 (39.4)
1,150 (45.3)
1,320 (52.0)
1,400 (55.1)
1,550 (61.0)
985 (38.8)
1,070 (42.1)
1,290 (50.8)
1,140 (44.9)
1,410 (55.5)
1,790 (70.5)
935 (36.8)
820 (32.3)
1,120 (44.1)
1,270 (50.0)
1,440 (56.7)
1,520 (59.8)
1,670 (65.7)
-
-
-
-
-
-
1,035 (40.7)
570 (1,260)
700 (1,540)
770 (1,700)
830 (1,830)
850 (1,870)
920 (2,030)
770 (1,700)
810 (1,790)
890 (1,960)
900 (1,980)
1,030 (2,270)
880 (1,940)
460 (1,010)
8.2 (26’ 11”) Boom
6.3 (20’ 8”) Arm2.0 (6’ 7”) Arm 2.92 (9’ 7”) Arm 2.4 (7’ 10”) Arm 3.9 (12’ 10”) Arm
mm (ft.in)
kg (lb)
mm (ft.in)
kg (lb)
2,000 (6’ 7”)
975 (2,150)
133.4 [144.8]
13600 [14770]
29980 [32550]
152.0 [165.0]
15500 [16830]
34170 [37100]
144.2 [156.5]
14700 [15960]
32410 [35190]
151.0 [164.0]
15400 [16720]
33950 [36860]
133.4 [144.8]
13600 [14770]
29980 [32550]
152.0 [165.0]
15500 [16830]
34170 [37100]
119.6 [129.9]
12200 [13250]
26900 [29210]
125.5 [136.3]
12800 [13900]
28220 [30640]
133.4 [144.8]
13600 [14770]
29980 [32550]
152.0 [165.0]
15500 [16830]
34170 [37100]
102.0 [110.7]
10400 [11290]
22930 [24900]
106.9 [116.1]
10900 [11830]
24030 [26090]
133.4 [144.8]
13600 [14770]
29980 [32550]
152.0 [165.0]
15500 [16830]
34170 [37100]
84.3 [91.6]
8600 [9340]
18960 [20590]
87.3 [94.8]
8900 [9660]
19620 [21300]
72.6
7400
16310
83.4
8500
18740
49.0
5000
11020
50.0
5100
11240
2,400 (7’ 10”)
1,045 (2,300)
2,920 (9’ 7”)
1,095 (2,410)
3,900 (12’ 10”)
1,295 (2,850)
8,200 (26’ 11”)
2,350 (5,180)
6,300 (20’ 8”)
1,330 (2,930)
5,680 (18’ 8”)
1,950 (4,300)
SAE
kN
kgf
lbf
ISO
kN
kgf
lbf
SAE
kN
kgf
lbf
ISO
kN
kgf
lbf
0.51 (0.67) 0.80 (1.05)0.92 (1.20)
0.74 (0.97)0.90 (1.18)1.05 (1.37)
0.87 (1.14)1.20 (1.57)
0.75 (0.98) 0.52 (0.68)1.10 (1.44)1.20 (1.57)
1.34 (1.75)
BoomLength
Weight
Arm
Bucketdigging
force
Armcrowdforce
[ ]:PowerBoost
RemarksLength
Weight
3
:
:
:
BUCKETS R220NLC-9AAll buckets are welded with high-strength steel.
SAE heaped m3 (yd3)
ATTACHMENT R220NLC-9ABooms and arms are welded, a low-stress, full-box section design. 5.65 m (18’ 6”) mono boom, 5.65 m (18’ 6”) hydraulic adjustable boom and 2.00 m (6’ 7”); 2.40 m (7’ 10”) and 2.92 m (9’ 7”) arms are available.
Note: Boom weight includes arm cylinder, piping and pin. Arm weight includes bucket cylinder, linkage and pin.
DIGGING FORCE R220NLC-9A
Capacity m3 (yd3)
SAE heaped CECE heaped
Width mm (in)
Without side cutters
With side cutters
Weight kg (lb)
Heavy-duty bucket
Heavy duty Rock-bucket
Slope finishing bucket
Applicable for materials with density of 2,000 kg/m3 (3,370 lb/yd3) or less
Applicable for materials with density of 1,600 kg/m3 (2,700 lb/yd3) or less
Applicable for materials with density of 1,100 kg/m3 (1,850 lb/yd3) or less
0.51 (0.67)
0.80 (1.05)
0.87 (1.14)
0.92 (1.20)
1.10 (1.44)
1.20 (1.57)
1.34 (1.75)
0.74 (0.97)
0.90 (1.18)
1.05 (1.37)
0.87 (1.14)
0.75 (0.98)
0.45 (0.59)
0.70 (0.92)
0.75 (0.98)
0.80 (1.05)
0.96 (1.26)
1.00 (1.31)
1.15 (1.50)
0.65 (0.85)
0.80 (1.05)
0.92 (1.20)
0.75 (0.98)
0.65 (0.85)
700 (27.6)
1,000 (39.4)
1,090 (42.9)
1,150 (45.3)
1,320 (52.0)
1,400 (55.1)
1,550 (61.0)
985 (38.8)
1,070 (42.0)
1,290 (50.8)
1,140 (44.9)
1,790 (70.5)
820 (32.3)
1,120 (44.1)
1,210 (47.6)
1,270 (50.0)
1,440 (56.7)
1,520 (59.8)
1,670 (65.7)
-
-
-
-
-
570 (1,260)
700 (1,540)
740 (1,630)
770 (1,700)
830 (1,830)
850 (1,870)
920 (2,030)
770 (1,700)
810 (1,790)
890 (1,960)
900 (1,980)
880 (1,940)
Recommendation m (ft.in)
5.65 (18’ 6”) Mono boom 5.65 (18’ 6”) Hydraulic adjustable boom
2.40 (7’ 10”) Arm2.00 (6’ 7”) Arm 2.92 (9’ 7”) Arm 2.40 (7’ 10”) Arm 2.00 (6’ 7”) Arm
mm (ft.in)
kg (lb)
mm (ft.in)
kg (lb)
2,000 (6’ 7”)
975 (2,150)
130.4 [141.6]
13,300 [14,440]
29,320 [31,830]
149.1 [161.8]
15,200 [16,500]
33,510 [36,380]
144.2 [156.5]
14,700 [15,960]
32,410 [35,190]
151.0 [164.0]
15,400 [16,720]
33,950 [36,860]
130.4 [141.6]
13,300 [14,440]
29,320 [31,830]
149.1 [161.8]
15,200 [16,500]
33,510 [36,380]
119.6 [129.9]
12,200 [13,250]
26,900 [29,210]
125.5 [136.3]
12,800 [13,900]
28,220 [30,640]
130.4 [141.6]
13,300 [14,440]
29,320 [31,830]
149.1 [161.8]
15,200 [16,500]
33,510 [36,380]
102.0 [110.7]
10,400 [11,290]
22,930 [24,900]
106.9 [116.1]
10,900 [11,830]
24,030 [26,090]
2,400 (7’ 10”)
1,045 (2,300)
2,920 (9’ 7”)
1,095 (2,410)
5,650 (18’ 6”)
1,950 (4,300)
SAE
kN
kgf
lbf
ISO
kN
kgf
lbf
SAE
kN
kgf
lbf
ISO
kN
kgf
lbf
0.51 (0.67) 0.80 (1.05)0.87 (1.14)0.92 (1.20)
0.74 (0.97) 0.90 (1.18)1.05 (1.37)
0.87 (1.14) 0.75 (0.98)1.10 (1.44)1.20 (1.57)
1.34 (1.75)
BoomLength
Weight
Arm
Bucketdigging
force
Armcrowdforce
[ ]:PowerBoost
RemarksLength
Weight
4
DIMENSIONS R220LC-9A / R220LC-9A LR
WORKING RANGES R220LC-9A / R220LC-9A LR
Dimensions & Working Ranges
mm (ft · in)mm (ft . in)
mm (ft · in)
Boom length
Arm length
Overall length
Overall heightof boom
Track shoe width
Overall width
Boom length
Arm length
Max. digging reach
Max. diggingreach on ground
Max. digging depth
Max. diggingdepth (8’ level)
Max. vertical walldigging depth
Max. digging height
Max. dumping height
Min. front swing radius
Tumbler distance
Overall length of crawler
Ground clearance of counterweight
Tail swing radius
Rear-end length
Overall width of upperstructure
Overall height of cab
Min. ground clearance
Track gauge
A
B
C
D
D’
E
F
G
H
I
J
K
L
A
A’
B
B’
C
D
E
F
2,000(6’ 7”)
9,140(29’ 12”)
8,960(29’ 5”)
5,820(19’ 1”)
5,580(18’ 4”)
5,280(17’ 4”)
9,140(29’ 12”)
6,330(20’ 9”)
3,750(12’ 4”)
2,400(7’ 10”)
9,500(31’ 2”)
9,330(30’ 7”)
6,220(20’ 5”)
6,010(19’ 9”)
5,720(18’ 9”)
9,340(30’ 8”)
6,520(21’ 5”)
3,740(12’ 3”)
2,920(9’ 7”)
9,980(32’ 9”)
9,820(32’ 3”)
6,730(22’ 1”)
6,560(21’ 6”)
6,280(20’ 7”)
9,600(31’ 6”)
6,780(22’ 3”)
3,740(12’ 3”)
3,900(12’ 10”)
6,300(20’ 8”)
8,200(26’ 11”)
10,910(35’10”)
15,220(49’ 11”)
10,770(35’ 4”)
15,120(49’ 7”)
7,720(25’ 4”)
11,760(38’ 7”)
7,580(24’ 10”)
11,650(38’ 3”)
7,240(23’ 9”)
9,610(31’ 6”)
10,110(33’ 2”)
12,550(41’ 2”)
7,290(23’ 11”)
10,280(33’ 9”)
3,650(11’ 12”)
4,870(15’ 12”)
5,680(18’ 8”)
3,650 (11’ 12”)
4,440 (14’ 7”)
1,060 (3’ 6”)
2,840 (9’ 4”)
2,770 (9’ 1”)
2,740 (8’ 12”)
2,920 (9’ 7”)
480 (1’ 7”)
2,390 (7’ 10”)
2,000(6’ 7”)
9,650(31’ 8”)
3,200(10’ 6”)
600(24”)
2,990(9’ 10”)
2,400(7’ 10”)
9,570(31’ 5”)
3,110(10’ 2”)
700(28”)
3,090(10’ 2”)
2,920(9’ 7”)
9,530(31’ 3”)
3,030(9’ 11”)
800(32”)
3,190(10’ 6”)
3,900(12’ 10”)
6,300(20’ 8”)
9,520(31’ 3”)
12,030(39’ 6”)
3,480(11’ 5”)
3,280(10’ 9”)
900(36”)
3,290(10’ 10”)
5,680 (18’ 8”)
8,200(26’ 11”)
5
ED (D')
LK
HBA
I
J F
GC
DIMENSIONS R220NLC-9A
WORKING RANGES R220NLC-9A
Dimensions & Working Ranges
mm (ft · in)mm (ft . in)
mm (ft · in)
Boom length
Arm length
Overall length
Overall heightof boom
Track shoe width
Overall width
Boom length
Arm length
Max. digging reach
Max. diggingreach on ground
Max. digging depth
Max. diggingdepth (8’ level)
Max. vertical walldigging depth
Max. digging height
Max. dumping height
Min. front swing radius
Tumbler distance
Overall length of crawler
Ground clearance of counterweight
Tail swing radius
Rear-end length
Overall width of upperstructure
Overall height of cab
Min. ground clearance
Track gauge
A
B
C
D
D’
E
F
G
H
I
J
K
L
A
A’
B
B’
C
D
E
F
2,000(6’ 7”)
9,140(29’ 12”)
8,960(29’ 5”)
5,750(18’ 10”)
5,520(18’ 1”)
5,320(17’ 5”)
9,270(30’ 5”)
6,450(21’ 2”)
3,710(12’ 2”)
2,400(7’ 10”)
9,510(31’ 2”)
9,340(30’ 8”)
6,150(20’ 2”)
5,950(19’ 6”)
5,780(19’ 0”)
9,500(31’ 2”)
6,660(21’ 10”)
3,630(11’ 11”)
2,920(9’ 7”)
9,960(32’ 8”)
9,800(32’ 2”)
6,640(21’ 9”)
6,470(21’ 3”)
6,250(20’ 6”)
9,740(31’ 11”)
6,900(22’ 8”)
3,580(11’ 9”)
5,650 (18’ 6”)
3,650 (12’ 0”)
4,440 (14’ 7”)
1,060 (3’ 6”)
2,800 (9’ 2”)
2,770 (9’ 1”)
2,530 (8’ 4”)
2,920 (9’ 7”)
480 (1’ 7”)
2,000 (6’ 7”)
500(20”)
2,500(8’ 2”)
600(24”)
2,600(8’ 6”)
2,000(6’ 7”)
9,650(31’ 8”)
3,250(10’ 8”)
2,400(7’ 10”)
9,570(31’ 5”)
3,170(10’ 5”)
2,920(9’ 7”)
9,510(31’ 2”)
3,100(10’ 2”)
700(28”)
2,700(8’ 9”)
5,650 (18’ 6”)
6
ED (D')
LK
HBA
I
JF
GC
DIMENSIONS R220NLC-9A - HYDRAULIC ADJUSTABLE BOOM
WORKING RANGES R220NLC-9A - HYDRAULIC ADJUSTABLE BOOM
Dimensions & Working Ranges
mm (ft · in)mm (ft . in)
mm (ft · in)
Boom length
Arm length
Overall length
Overall heightof boom
Track shoe width
Overall width
Boom length
Arm length
Max. digging reach
Max. diggingreach on ground
Max. digging depth
Max. diggingdepth (8’ level)
Max. vertical walldigging depth
Max. digging height
Max. dumping height
Min. front swing radius
Tumbler distance
Overall length of crawler
Ground clearance of counterweight
Tail swing radius
Rear-end length
Overall width of upperstructure
Overall height of cab
Min. ground clearance
Track gauge
A
B
C
D
D’
E
F
G
H
I
J
K
L
A
A’
B
B’
C
D
E
F
2,000(6’ 7”)
9,120(29’ 11”)
8,940(29’ 4”)
5,480(17’ 12”)
5,360(17’ 7”)
4,560(14’ 12”)
10,300(33’ 10”)
7,390(24’ 3”)
2,870(9’ 5”)
2,400(7’ 10”)
9,530(31’ 3”)
9,360(30’ 9”)
5,890(19’ 4”)
5,770(18’ 11”)
4,990(16’ 4”)
10,670(35’ 0”)
7,740(25’ 5”)
2,670(8’ 9”)
5,650 (18’ 6”)
3,650 (12’ 0”)
4,440 (14’ 7”)
1,060 (3’ 6”)
2,800 (9’ 2”)
2,770 (9’ 1”)
2,530 (8’ 4”)
2,920 (9’ 7”)
480 (1’ 7”)
2,000 (6’ 7”)
500(20”)
2,500(8’ 2”)
600(24”)
2,600(8’ 6”)
2,000(6’ 7”)
9,620(31’ 7”)
3,050(10’ 0”)
2,400(7’ 10”)
9,550(31’ 4”)
3,000(9’ 10”)
700(28”)
2,700(8’ 9”)
5,650 (18’ 6”)
7
DIMENSIONS R220LC-9A HIGH WALKER
WORKING RANGES R220LC-9A HIGH WALKER
Dimensions & Working Ranges
mm (ft · in)mm (ft . in)
mm (ft · in)
Boom length
Arm length
Overall length
Overall heightof boom
Track shoe width
Overall width
Boom length
Arm length
Max. digging reach
Max. diggingreach on ground
Max. digging depth
Max. diggingdepth (8’ level)
Max. vertical walldigging depth
Max. digging height
Max. dumping height
Min. front swing radius
Tumbler distance
Overall length of crawler
Ground clearance of counterweight
Tail swing radius
Rear-end length
Overall width of upperstructure
Overall height of cab
Min. ground clearance
Track gauge
A
B
C
D
D’
E
F
G
H
I
J
K
L
A
A’
B
B’
C
D
E
F
3,650 (11’ 12”)
4,440 (14’ 7”)
1,240 (4’ 1”)
2,840 (9’ 4”)
2,770 (9’ 1”)
2,740 (8’ 12”)
3,100 (10’ 2”)
660 (2’ 2”)
2,790 (9’ 2”)
2,000(6’ 7”)
2,400(7’ 10”)
2,920(9’ 7”)
3,900(12’ 10”)
9,140 (29’ 12”)
9,500(31’ 2”)
9,980(32’ 9”)
10,910(35’ 10”)
8,920(29’ 3”)
9,290(30’ 6”)
9,820(32’ 3”)
10,730(35’ 2”)
5,630(18’ 6”)
6,010(19’ 9”)
6,550(21’ 6”)
7,530(24’ 8”)
5,390(17’ 8”)
5,820(19’ 1”)
6,380(20’ 11”)
7,390(24’ 3”)
5,090(16’ 8”)
5,630(18’ 6”)
6,100(20’ 0”)
7,050(23’ 2”)
9,330(30’ 7”)
9,530(31’ 3”)
9,780(32’ 1”)
10,300(33’ 10”)
6,520(21’ 5”)
6,710(22’ 0”)
6,960(22’ 10”)
7,480(24’ 6”)
3,750(12’ 4”)
3,740(12’ 3”)
3,740(12’ 3”)
3,650(11’ 12”)
5,680 (18’ 8”)
2,000(6’ 7”)
9,650(31’ 8”)
3,290(10’ 10”)
2,400(7’ 10”)
9,550(31’ 4”)
3,170(10’ 5”)
2,920(9’ 7”)
9,470(31’ 1”)
3,060(10’ 0”)
3,900(12’ 10”)
9,560(31’ 4”)
3,450(11’ 4”)
5,680 (18’ 8”)
3,395(11’ 2”)
3,495(11’ 6”)
3,595(11’ 10”)
3,505(11’ 6”)
Triple grouser
700 (28”) 800 (32”)
Double grouser
710 (28”)
Type
Width 600 (24”)
8
R220LC-9A Rating over-front Rating over-side or 360 degrees
Lifting Capacities
Boom : 5.68 m (18’ 8”) / Arm : 2.0 m (6’ 7”) / Bucket : 0.92 m3 (1.20 yd3) SAE heaped / Shoe : 600 mm (24”) triple grouser
Load pointheightm (ft)
Load radius At max. reachCapacity Reach
GroundLine
Boom : 5.68 m (18’ 8”) / Arm : 2.40 m (7’ 10”) / Bucket : 0.92 m3 (1.20 yd3) SAE heaped / Shoe : 600 mm (24”) triple grouser
Load pointheightm (ft)
Load radius At max. reachCapacity Reach
GroundLine
Boom : 5.68 m (18’ 8”) / Arm : 2.92 m (9’ 7”) / Bucket : 0.92 m3 (1.20 yd3) SAE heaped / Shoe : 600 mm (24”) triple grouser
Load pointheightm (ft)
Load radius At max. reachCapacity Reach
GroundLine
1. Lifting capacity is based on SAE J1097, ISO 10567.2. Lifting capacity of the Robex Series does not exceed 75% of the tipping load with the machine on firm, level ground or 87% of full hydraulic capacity.
3. The load point is a hook located on the back of the bucket.4. (*) indicates the load limited by hydraulic capacity.
9
Lifting CapacitiesR220LC-9A Rating over-front Rating over-side or 360 degrees
Boom : 5.68 m (18’ 8”) / Arm : 3.90 m (12’ 10”) / Bucket : 0.92 m3 (1.20 yd3) SAE heaped / Shoe : 600 mm (24”) triple grouser
Load pointheightm (ft)
Load radius At max. reachCapacity Reach
GroundLine
R220LC-9A HIGH WALKER Rating over-front Rating over-side or 360 degrees
Boom : 5.68 m (18’ 8”) / Arm : 2.40 m (7’ 10”) / Bucket : 0.92 m3 (1.20 yd3) SAE heaped / Shoe : 600 mm (24”) triple grouser
Load pointheightm (ft)
Load radius At max. reachCapacity Reach
GroundLine
Boom : 5.68 m (18’ 8”) / Arm : 2.92 m (9’ 7”) / Bucket : 0.92 m3 (1.20 yd3) SAE heaped / Shoe : 600 mm (24”) triple grouser
Load pointheightm (ft)
Load radius At max. reachCapacity Reach
GroundLine
10
R220LC-9A HIGH WALKER Rating over-front Rating over-side or 360 degrees
Lifting Capacities
Boom : 5.68 m (18’ 8”) / Arm : 3.90 m (12’ 10”) / Bucket : 0.92 m3 (1.20 yd3) SAE heaped / Shoe : 600 mm (24”) triple grouser
Load pointheightm (ft)
Load radius At max. reachCapacity Reach
GroundLine
Boom : 5.68 m (18’ 8”) / Arm : 2.40 m (7’ 10”) / Bucket : 0.92 m3 (1.20 yd3) SAE heaped / Shoe : 800 mm (32”) triple grouser
Load pointheightm (ft)
Load radius At max. reachCapacity Reach
GroundLine
Boom : 5.68 m (18’ 8”) / Arm : 2.92 m (9’ 7”) / Bucket : 0.92 m3 (1.20 yd3) SAE heaped / Shoe : 800 mm (32”) triple grouser
Load pointheightm (ft)
Load radius At max. reachCapacity Reach
GroundLine
11
Lifting CapacitiesR220LC-9A HIGH WALKER Rating over-front Rating over-side or 360 degrees
Boom : 5.68 m (18’ 8”) / Arm : 3.90 m (12’ 10”) / Bucket : 0.92 m3 (1.20 yd3) SAE heaped / Shoe : 600 mm (24”) triple grouser
Load pointheightm (ft)
Load radius At max. reachCapacity Reach
GroundLine
R220LC-9A LONG REACH Rating over-front Rating over-side or 360 degrees
Boom : 8.2 m (26’ 11”) / Arm : 6.3 m (20’ 8”) / Bucket : 0.52 m3 (0.68 yd3) SAE heaped / Shoe : 800 mm (32”) triple grouser with 5,300 kg (11,680 lb) Counterweight
Load pointheightm (ft)
Load radius At max. reachCapacity Reach
GroundLine
1. Lifting capacity is based on SAE J1097, ISO 10567.2. Lifting capacity of the Robex Series does not exceed 75% of the tipping load with the machine on firm, level ground or 87% of full hydraulic capacity.
3. The load point is a hook located on the back of the bucket.4. (*) indicates the load limited by hydraulic capacity.
12
R220NLC-9A MONO BOOM Rating over-front Rating over-side or 360 degrees
Lifting Capacities
Boom : 5.65 m (18’ 6”) / Arm : 2.00 m (6’ 7”) / Bucket : 0.87 m3 (1.14 yd3) SAE heaped / Shoe : 500 mm (20”) triple grouser
Load pointheightm (ft)
Load radius At max. reachCapacity Reach
GroundLine
Boom : 5.65 m (18’ 6”) / Arm : 2.40 m (7’ 10”) / Bucket : 0.87 m3 (1.14 yd3) SAE heaped / Shoe : 500 mm (20”) triple grouser
Load pointheightm (ft)
Load radius At max. reachCapacity Reach
GroundLine
Boom : 5.65 m (18’ 6”) / Arm : 2.92 m (9’ 7”) / Bucket : 0.87 m3 (1.14 yd3) SAE heaped / Shoe : 500 mm (20”) triple grouser
Load pointheightm (ft)
Load radius At max. reachCapacity Reach
GroundLine
1. Lifting capacity is based on SAE J1097, ISO 10567.2. Lifting capacity of the Robex Series does not exceed 75% of the tipping load with the machine on firm, level ground or 87% of full hydraulic capacity.
3. The load point is a hook located on the back of the bucket.4. (*) indicates the load limited by hydraulic capacity.
13
R220NLC-9A / HYDRAULIC ADJUSTABLE BOOM Rating over-front Rating over-side or 360 degrees
Lifting Capacities
Boom : 5.65 m (18’ 6”) / Arm : 2.00 m (6’ 7”) / Bucket : 0.87 m3 (1.14 yd3) SAE heaped / Shoe : 500 mm (20”) triple grouser
Load pointheightm (ft)
Load radius At max. reachCapacity Reach
GroundLine
Boom : 5.65 m (18’ 6”) / Arm : 2.40 m (7’ 10”) / Bucket : 0.87 m3 (1.14 yd3) SAE heaped / Shoe : 500 mm (20”) triple grouser
Load pointheightm (ft)
Load radius At max. reachCapacity Reach
GroundLine
1. Lifting capacity is based on SAE J1097, ISO 10567.2. Lifting capacity of the Robex Series does not exceed 75% of the tipping load with the machine on firm, level ground or 87% of full hydraulic capacity.
3. The load point is a hook located on the back of the bucket.4. (*) indicates the load limited by hydraulic capacity.
www.hyundai.eu EN - 2013.11 Rev 0
STANDARD EQUIPMENT R220LC-9A / R220NLC-9A
ISO Standard cabinAll-weather steel cab with 360° visibilitySafety glass windowsRise-up type windshield wiperSliding fold-in front windowSliding side window (LH)One key fits all lockable doorsHot & cool boxStorage compartment & AshtrayRadio / MP3 Player with remote control and USB-input Handsfree mobile phone system with USB-charging device Transparent cabin roof-cover12 volt power outlet (24V DC to 12V DC converter)Sun visorRain guard - front window
Computer aided power optimization (CAPO) system3-power modes, 2-work modes, User modeAuto & one-touch deceleration systemAuto warm-up systemOverheat prevention system
Automatic temperature controlAir conditioner & heaterDefroster
Self-diagnostics systemStarting Aid (air grid heater) for cold weatherCentralized monitoring
LCD displayEngine speed or Trip meterClockGauges- Fuel level gauge- Engine coolant temperature gauge- Hyd. oil temperature gaugeWarning lamps- Engine warning- Overload- Communication error- Low battery- Air filter clogging Indicators- Max power- Low speed/High speed- Fuel warmer- Auto decelerationRearview camera
Door and cab locks, one keyThree outside rearview mirrorsMechanical suspension seat with heater Adjustable joysticksConsole box tilting systemFour front working lightsElectric hornBatteries (2 x 12V x 100 AH)Battery master switchRemovable clean-out screen for coolersAutomatic swing brakeFuel pre-filter with fuel warmerBoom holding systemArm holding systemTrack shoes (600 mm; 24”)Track rail guardAccumulator for lowering work equipmentLower frame under coverViscous fan clutchFuel filler pump (50 ℓ/min)Safety lock valve for boom cylinder with overload warning deviceDouble-acting piping kit (clamshell, etc.)Travel alarm
Boom5.68 m; 18’ 8”
Arm2.92 m; 9’ 7”
Cabin ROPS (ISO 12117-2)ROPS (Roll Over Protective Structure)
Hi-mate (Remote Management System)
OPTIONAL EQUIPMENT R220LC-9A / R220NLC-9A
Beacon lampSafety lock valve for arm cylinderSingle-acting piping kit (breaker, etc.)Quick couplerBoom - R220LC-9A
5.68 m; 18’ 8” - Heavy duty8.2 m; 26’ 11” - Long reach
Boom - R220NLC-9A5.65 m; 18’ 6”5.65 m; 18’ 6” - hydraulic adjustable
Arm - R220LC-9A2.0 m; 6’ 7”2.4 m; 7’ 10”2.92 m; 9’ 7” Heavy duty3.9 m; 12’ 10”6.3 m, 20’ 8” Long reach
Arm - R220NLC-9A2.0 m; 6’ 7”2.4 m; 7’ 10”2.92 m; 9’ 7” - not for hydraulic adjustable boom
Cabin FOPS/FOG (ISO/DIS 10262 Level II)FOPS (Falling Object Protective Structure)FOG (Falling Object Guard)
Cabin guard frontWire netFine net
Cabin roof-steel coverCabin lightsTrack shoes - R220LC-9A
Triple grousers shoe (700 mm; 28”)Triple grousers shoe (800 mm; 32”)Triple grousers shoe (900 mm; 36”)Double grousers shoe (700 mm; 28”)Full track rail guard (High walker only)
Track shoes - R220NLC-9ATriple grousers shoe (500 mm; 20” )Triple grousers shoe (600 mm; 25” )Triple grousers shoe (700 mm; 28” )
Additional lower frame - reinforced under coverSeat
Adjustable air suspension seatAdjustable air suspension seat with heaterMechanical suspension seat
Pattern change valve (2 patterns)Air compressor
* Standard and optional equipment may vary. Contact your Hyundai dealer for more information. The machine may vary according to international standards.
* The photos may include attachments and optional equipment that are not available in your area.
* Materials and specifications are subject to change without advance notice.* All imperial measurements rounded off to the nearest pound or inch.
PLEASE CONTACT