Specifications R220LC-9A / R220NLC-9A...1 ENGINE MODEL CUMMINS QSB6.7 Type Water cooled, 4 cycle Diesel, 6-Cylinders in line, direct injection, turbocharged, charged air cooled and

1

ENGINE

MODEL CUMMINS QSB6.7

TypeWater cooled, 4 cycle Diesel, 6-Cylindersin line, direct injection, turbocharged,charged air cooled and low emission

Rated flywheel horse power

SAEJ1995 (gross) 167 HP (124 kW) / 1,950 rpm

J1349 (net) 157 HP (117 kW) / 1,950 rpm

DIN6271/1 (gross) 169 PS (124 kW) / 1,950 rpm

6271/1 (net) 159 PS (117 kW) / 1,950 rpm

Max. torque 74.7 kgf.m (540 lbf.ft) / 1,500 rpm

Bore x stroke 107 mm x 124 mm (4.2” x 4.9”)

Piston displacement 6,700 cc (409 in3)

Batteries 2 x 12 V x 100 AH

Starting motor 24 V; 4.8 kW

Alternator 24 V, 95 Amp

* This engine meets the EPA (Tier 4 interim) / EU (Stage III-B) Emission regulation.

HYDRAULIC SYSTEM

MAIN PUMPType Two variable displacement axial piston pumps

Max. flow 2 x 228.2 ℓ/min (60.3 US gpm/50.2 UK gpm)

Sub-pump for pilot circuit Gear pump

Cross-sensing and fuel saving pump system

HYDRAULIC MOTORS

TravelTwo-speed axial piston motorwith brake valve and parking brake

Swing Axial piston motor with automatic brake

RELIEF VALVE SETTINGImplement circuits 350 kgf/cm2 (4,978 psi)

Travel 350 kgf/cm2 (4,978 psi)

Power boost (boom, arm, bucket) 380 kgf/cm2 (5,404 psi)

Swing circuit 265 kgf/cm2 (3,769 psi)

Pilot circuit 40 kgf/cm2 (568 psi)

Service valve Installed

HYDRAULIC CYLINDERS

No. of cylinder- bore x stroke

Boom: 2-120 x 1,290 mm (4.7” x 50.8”)

Arm: 1-140 x 1,510 mm (5.5” x 59.4”)

Bucket: 1-120 x 1,055 mm (4.7” x 41.5”)

DRIVES & BRAKES

Drive method Fully hydrostatic type

Drive motor Axial piston motor, in-shoe design

Reduction system Planetary reduction gear

Max. drawbar pull 21,100 kgf (46,500 lbf )

Max. travel speed (high) / (low) 5.7 km/h (3.5 mph) / 3.6 km/h (2.2 mph)

Gradeability 35° (70 %)

Parking brake Multi wet disc

CONTROLPilot pressure operated joysticks and pedals with detachable lever provide almost effortless and fatigueless operation.

Pilot controlTwo joysticks with one safety lever (LH): Swing and arm(RH): Boom and bucket (ISO)

Traveling and steering Two levers with pedals

Engine throttle Electric, Dial type

SWING SYSTEM

Swing motor Fixed displacement axial piston motor

Swing reduction Planetary gear reduction

Swing bearing lubrication Grease-bathed

Swing brake Multi wet disc

Swing speed 10.7 rpm

COOLANT & LUBRICANT CAPACITY

Refilling liter US gal UK gal

Fuel tank 400 105.7 88.0

Engine coolant 35 9.2 7.7

Engine oil 23.7 6.3 5.2

Swing device 6 1.6 1.3

Final drive (each) 6 1.6 1.3

Hydraulic system (including tank) 275 72.6 60.5

Hydraulic tank 160 42.3 35.2

UNDERCARRIAGEThe X-leg type center frame is integrally welded with reinforced box-section trackframes. The undercarriage includes lubricated rollers, idlers, track adjusters with shockabsorbing springs and sprockets, and a track chain with double or triple grouser shoes.

Center frame X - leg type

Track frame Pentagonal box type

No. of shoes on each side 49

No. of carrier rollers on each side 2

No. of track rollers on each side 9

No. of rail guards on each side 2

OPERATING WEIGHT (APPROXIMATE)Operating weight, including 5,680 mm (18’ 8”) boom, 2,920 mm (9’ 7”) arm, SAE heaped 0.92 m3 (1.20 yd3) bucket, lubricant, coolant, full fuel tank, full hydraulic tank and all standard equipments.

MAJOR COMPONENT WEIGHTUpperstructure 5,600 kg (12,350 lb)

Boom (with arm cylinder) 1,950 kg (4,300 lb)

Arm (with bucket cylinder) 1,095 kg (2,410 lb)

OPERATING WEIGHTShoes Operating weight Ground pressure

Type Width mm (in) kg (lb) kgf/cm2 (psi)

Triplegrouser

500 (20”)R220NLC-9A 22,000 (48,500) 0.55 (7.82)

R220NLC-9A 2pc 22,480 (49,560) 0.56 (7.97)

600 (24”)

R220LC-9A 21,900 (48,280) 0.46 (6.54)

R220NLC-9A 22,350 (49,280) 0.47 (6.68)

R220NLC-9A 2pc 22,830 (50,330) 0.48 (6.83)

R220LC-9A H/W 23,360 (51,500) 0.50 (7.11)

R220LC-9A LR 24,360 (53,700) 0.51 (7.25)

700 (28”)

R220LC-9A 22,250 (49,050) 0.40 (5.69)

R220NLC-9A 22,700 (50,050) 0.41 (5.83)

R220NLC-9A 2pc 23,180 (51,100) 0.42 (5.98)

R220LC-9A H/W 23,710 (52,270) 0.43 (6.11)

R220LC-9A LR 24,710 (54,500) 0.45 (6.40)

800 (32”)

R220LC-9A 22,515 (49,640) 0.36 (5.12)

R220LC-9A H/W 23,975 (52,860) 0.38 (5.40)

R220LC-9A LR 24,975 (55,050) 0.40 (5.69)

900 (36”) R220LC-9A 22,760 (50,180) 0.32 (4.55)

R220LC-9A LR 25,220 (55,600) 0.36 (5.12)

Double grouser 700 (28”) R220LC-9A H/W 24,135 (53,210) 0.43 (6.11)

Specifications R220LC-9A / R220NLC-9A

2

BUCKETS R220LC-9A / R220LC-9A LR / R220LC-9A H/WAll buckets are welded with high-strength steel.

SAE heaped m3 (yd3)

ATTACHMENT R220LC-9A / R220LC-9A LR / R220LC-9A H/WBooms and arms are welded, a low-stress, full-box section design. 5.68 m (18’ 8”) & 8.2 m (26’ 11”) Booms and 2.0 m (6’ 7”); 2.4 m (7’ 10”); 2.92 m (9’ 7”); 3.9 m (12’ 10”) & 6.3 m (20’ 8”) Arms are available.

Note: Boom weight includes arm cylinder, piping and pin. Arm weight includes bucket cylinder, linkage and pin.

DIGGING FORCE R220LC-9A / R220LC-9A LR / R220LC-9A H/W

Capacity m3 (yd3)

SAE heaped CECE heaped

Width mm (in)

Without side cutters

With side cutters

Weight kg (lb)

Recommendation m (ft.in)

5.68 (18’ 8”) Boom

Heavy-duty bucket

Heavy duty Rock-bucket

Slope finishing bucket

Long reach bucket

Applicable for materials with density of 2,000 kg/m3 (3,370 lb/yd3) or less



0.51 (0.67)

0.80 (1.05)

0.92 (1.20)

1.10 (1.44)

1.20 (1.57)

1.34 (1.75)

0.74 (0.97)

0.90 (1.18)

1.05 (1.37)

0.87 (1.14)

1.20 (1.57)

0.75 (0.98)

0.52 (0.68)

0.45 (0.59)

0.70 (0.92)

0.80 (1.05)

0.96 (1.26)

1.00 (1.31)

1.15 (1.50)

0.65 (0.85)

0.80 (1.05)

0.92 (1.20)

0.75 (0.98)

1.00 (1.31)

0.65 (0.85)

0.45 (0.59)

700 (27.6)

1,000 (39.4)

1,150 (45.3)

1,320 (52.0)

1,400 (55.1)

1,550 (61.0)

985 (38.8)

1,070 (42.1)

1,290 (50.8)

1,140 (44.9)

1,410 (55.5)

1,790 (70.5)

935 (36.8)

820 (32.3)

1,120 (44.1)

1,270 (50.0)

1,440 (56.7)

1,520 (59.8)

1,670 (65.7)

-

-

-

-

-

-

1,035 (40.7)

570 (1,260)

700 (1,540)

770 (1,700)

830 (1,830)

850 (1,870)

920 (2,030)

770 (1,700)

810 (1,790)

890 (1,960)

900 (1,980)

1,030 (2,270)

880 (1,940)

460 (1,010)

8.2 (26’ 11”) Boom

6.3 (20’ 8”) Arm2.0 (6’ 7”) Arm 2.92 (9’ 7”) Arm 2.4 (7’ 10”) Arm 3.9 (12’ 10”) Arm

mm (ft.in)

kg (lb)

mm (ft.in)

kg (lb)

2,000 (6’ 7”)

975 (2,150)

133.4 [144.8]

13600 [14770]

29980 [32550]

152.0 [165.0]

15500 [16830]

34170 [37100]

144.2 [156.5]

14700 [15960]

32410 [35190]

151.0 [164.0]

15400 [16720]

33950 [36860]

133.4 [144.8]

13600 [14770]

29980 [32550]

152.0 [165.0]

15500 [16830]

34170 [37100]

119.6 [129.9]

12200 [13250]

26900 [29210]

125.5 [136.3]

12800 [13900]

28220 [30640]

133.4 [144.8]

13600 [14770]

29980 [32550]

152.0 [165.0]

15500 [16830]

34170 [37100]

102.0 [110.7]

10400 [11290]

22930 [24900]

106.9 [116.1]

10900 [11830]

24030 [26090]

133.4 [144.8]

13600 [14770]

29980 [32550]

152.0 [165.0]

15500 [16830]

34170 [37100]

84.3 [91.6]

8600 [9340]

18960 [20590]

87.3 [94.8]

8900 [9660]

19620 [21300]

72.6

7400

16310

83.4

8500

18740

49.0

5000

11020

50.0

5100

11240

2,400 (7’ 10”)

1,045 (2,300)

2,920 (9’ 7”)

1,095 (2,410)

3,900 (12’ 10”)

1,295 (2,850)

8,200 (26’ 11”)

2,350 (5,180)

6,300 (20’ 8”)

1,330 (2,930)

5,680 (18’ 8”)

1,950 (4,300)

SAE

kN

kgf

lbf

ISO

kN

kgf

lbf

SAE

kN

kgf

lbf

ISO

kN

kgf

lbf

0.51 (0.67) 0.80 (1.05)0.92 (1.20)

0.74 (0.97)0.90 (1.18)1.05 (1.37)

0.87 (1.14)1.20 (1.57)

0.75 (0.98) 0.52 (0.68)1.10 (1.44)1.20 (1.57)

1.34 (1.75)

BoomLength

Weight

Arm

Bucketdigging

force

Armcrowdforce

[ ]:PowerBoost

RemarksLength

Weight

3

:

:

:

BUCKETS R220NLC-9AAll buckets are welded with high-strength steel.

SAE heaped m3 (yd3)

ATTACHMENT R220NLC-9ABooms and arms are welded, a low-stress, full-box section design. 5.65 m (18’ 6”) mono boom, 5.65 m (18’ 6”) hydraulic adjustable boom and 2.00 m (6’ 7”); 2.40 m (7’ 10”) and 2.92 m (9’ 7”) arms are available.

Note: Boom weight includes arm cylinder, piping and pin. Arm weight includes bucket cylinder, linkage and pin.

DIGGING FORCE R220NLC-9A

Capacity m3 (yd3)

SAE heaped CECE heaped

Width mm (in)

Without side cutters

With side cutters

Weight kg (lb)

Heavy-duty bucket

Heavy duty Rock-bucket

Slope finishing bucket




0.51 (0.67)

0.80 (1.05)

0.87 (1.14)

0.92 (1.20)

1.10 (1.44)

1.20 (1.57)

1.34 (1.75)

0.74 (0.97)

0.90 (1.18)

1.05 (1.37)

0.87 (1.14)

0.75 (0.98)

0.45 (0.59)

0.70 (0.92)

0.75 (0.98)

0.80 (1.05)

0.96 (1.26)

1.00 (1.31)

1.15 (1.50)

0.65 (0.85)

0.80 (1.05)

0.92 (1.20)

0.75 (0.98)

0.65 (0.85)

700 (27.6)

1,000 (39.4)

1,090 (42.9)

1,150 (45.3)

1,320 (52.0)

1,400 (55.1)

1,550 (61.0)

985 (38.8)

1,070 (42.0)

1,290 (50.8)

1,140 (44.9)

1,790 (70.5)

820 (32.3)

1,120 (44.1)

1,210 (47.6)

1,270 (50.0)

1,440 (56.7)

1,520 (59.8)

1,670 (65.7)

-

-

-

-

-

570 (1,260)

700 (1,540)

740 (1,630)

770 (1,700)

830 (1,830)

850 (1,870)

920 (2,030)

770 (1,700)

810 (1,790)

890 (1,960)

900 (1,980)

880 (1,940)

Recommendation m (ft.in)

5.65 (18’ 6”) Mono boom 5.65 (18’ 6”) Hydraulic adjustable boom

2.40 (7’ 10”) Arm2.00 (6’ 7”) Arm 2.92 (9’ 7”) Arm 2.40 (7’ 10”) Arm 2.00 (6’ 7”) Arm

mm (ft.in)

kg (lb)

mm (ft.in)

kg (lb)

2,000 (6’ 7”)

975 (2,150)

130.4 [141.6]

13,300 [14,440]

29,320 [31,830]

149.1 [161.8]

15,200 [16,500]

33,510 [36,380]

144.2 [156.5]

14,700 [15,960]

32,410 [35,190]

151.0 [164.0]

15,400 [16,720]

33,950 [36,860]

130.4 [141.6]

13,300 [14,440]

29,320 [31,830]

149.1 [161.8]

15,200 [16,500]

33,510 [36,380]

119.6 [129.9]

12,200 [13,250]

26,900 [29,210]

125.5 [136.3]

12,800 [13,900]

28,220 [30,640]

130.4 [141.6]

13,300 [14,440]

29,320 [31,830]

149.1 [161.8]

15,200 [16,500]

33,510 [36,380]

102.0 [110.7]

10,400 [11,290]

22,930 [24,900]

106.9 [116.1]

10,900 [11,830]

24,030 [26,090]

2,400 (7’ 10”)

1,045 (2,300)

2,920 (9’ 7”)

1,095 (2,410)

5,650 (18’ 6”)

1,950 (4,300)

SAE

kN

kgf

lbf

ISO

kN

kgf

lbf

SAE

kN

kgf

lbf

ISO

kN

kgf

lbf

0.51 (0.67) 0.80 (1.05)0.87 (1.14)0.92 (1.20)

0.74 (0.97) 0.90 (1.18)1.05 (1.37)

0.87 (1.14) 0.75 (0.98)1.10 (1.44)1.20 (1.57)

1.34 (1.75)

BoomLength

Weight

Arm

Bucketdigging

force

Armcrowdforce

[ ]:PowerBoost

RemarksLength

Weight

4

DIMENSIONS R220LC-9A / R220LC-9A LR

WORKING RANGES R220LC-9A / R220LC-9A LR

Dimensions & Working Ranges

mm (ft · in)mm (ft . in)

mm (ft · in)

Boom length

Arm length

Overall length

Overall heightof boom

Track shoe width

Overall width

Boom length

Arm length

Max. digging reach

Max. diggingreach on ground

Max. digging depth

Max. diggingdepth (8’ level)

Max. vertical walldigging depth

Max. digging height

Max. dumping height

Min. front swing radius

Tumbler distance

Overall length of crawler

Ground clearance of counterweight

Tail swing radius

Rear-end length

Overall width of upperstructure

Overall height of cab

Min. ground clearance

Track gauge

A

B

C

D

D’

E

F

G

H

I

J

K

L

A

A’

B

B’

C

D

E

F

2,000(6’ 7”)

9,140(29’ 12”)

8,960(29’ 5”)

5,820(19’ 1”)

5,580(18’ 4”)

5,280(17’ 4”)

9,140(29’ 12”)

6,330(20’ 9”)

3,750(12’ 4”)

2,400(7’ 10”)

9,500(31’ 2”)

9,330(30’ 7”)

6,220(20’ 5”)

6,010(19’ 9”)

5,720(18’ 9”)

9,340(30’ 8”)

6,520(21’ 5”)

3,740(12’ 3”)

2,920(9’ 7”)

9,980(32’ 9”)

9,820(32’ 3”)

6,730(22’ 1”)

6,560(21’ 6”)

6,280(20’ 7”)

9,600(31’ 6”)

6,780(22’ 3”)

3,740(12’ 3”)

3,900(12’ 10”)

6,300(20’ 8”)

8,200(26’ 11”)

10,910(35’10”)

15,220(49’ 11”)

10,770(35’ 4”)

15,120(49’ 7”)

7,720(25’ 4”)

11,760(38’ 7”)

7,580(24’ 10”)

11,650(38’ 3”)

7,240(23’ 9”)

9,610(31’ 6”)

10,110(33’ 2”)

12,550(41’ 2”)

7,290(23’ 11”)

10,280(33’ 9”)

3,650(11’ 12”)

4,870(15’ 12”)

5,680(18’ 8”)

3,650 (11’ 12”)

4,440 (14’ 7”)

1,060 (3’ 6”)

2,840 (9’ 4”)

2,770 (9’ 1”)

2,740 (8’ 12”)

2,920 (9’ 7”)

480 (1’ 7”)

2,390 (7’ 10”)

2,000(6’ 7”)

9,650(31’ 8”)

3,200(10’ 6”)

600(24”)

2,990(9’ 10”)

2,400(7’ 10”)

9,570(31’ 5”)

3,110(10’ 2”)

700(28”)

3,090(10’ 2”)

2,920(9’ 7”)

9,530(31’ 3”)

3,030(9’ 11”)

800(32”)

3,190(10’ 6”)

3,900(12’ 10”)

6,300(20’ 8”)

9,520(31’ 3”)

12,030(39’ 6”)

3,480(11’ 5”)

3,280(10’ 9”)

900(36”)

3,290(10’ 10”)

5,680 (18’ 8”)

8,200(26’ 11”)

5

ED (D')

LK

HBA

I

J F

GC

DIMENSIONS R220NLC-9A

WORKING RANGES R220NLC-9A



mm (ft · in)

Boom length

Arm length

Overall length


Track shoe width

Overall width

Boom length

Arm length

Max. digging reach


Max. digging depth



Max. digging height

Max. dumping height


Tumbler distance



Tail swing radius

Rear-end length




Track gauge

A

B

C

D

D’

E

F

G

H

I

J

K

L

A

A’

B

B’

C

D

E

F

2,000(6’ 7”)

9,140(29’ 12”)

8,960(29’ 5”)

5,750(18’ 10”)

5,520(18’ 1”)

5,320(17’ 5”)

9,270(30’ 5”)

6,450(21’ 2”)

3,710(12’ 2”)

2,400(7’ 10”)

9,510(31’ 2”)

9,340(30’ 8”)

6,150(20’ 2”)

5,950(19’ 6”)

5,780(19’ 0”)

9,500(31’ 2”)

6,660(21’ 10”)

3,630(11’ 11”)

2,920(9’ 7”)

9,960(32’ 8”)

9,800(32’ 2”)

6,640(21’ 9”)

6,470(21’ 3”)

6,250(20’ 6”)

9,740(31’ 11”)

6,900(22’ 8”)

3,580(11’ 9”)

5,650 (18’ 6”)

3,650 (12’ 0”)

4,440 (14’ 7”)

1,060 (3’ 6”)

2,800 (9’ 2”)

2,770 (9’ 1”)

2,530 (8’ 4”)

2,920 (9’ 7”)

480 (1’ 7”)

2,000 (6’ 7”)

500(20”)

2,500(8’ 2”)

600(24”)

2,600(8’ 6”)

2,000(6’ 7”)

9,650(31’ 8”)

3,250(10’ 8”)

2,400(7’ 10”)

9,570(31’ 5”)

3,170(10’ 5”)

2,920(9’ 7”)

9,510(31’ 2”)

3,100(10’ 2”)

700(28”)

2,700(8’ 9”)

5,650 (18’ 6”)

6

ED (D')

LK

HBA

I

JF

GC

DIMENSIONS R220NLC-9A - HYDRAULIC ADJUSTABLE BOOM

WORKING RANGES R220NLC-9A - HYDRAULIC ADJUSTABLE BOOM



mm (ft · in)

Boom length

Arm length

Overall length


Track shoe width

Overall width

Boom length

Arm length

Max. digging reach


Max. digging depth



Max. digging height

Max. dumping height


Tumbler distance



Tail swing radius

Rear-end length




Track gauge

A

B

C

D

D’

E

F

G

H

I

J

K

L

A

A’

B

B’

C

D

E

F

2,000(6’ 7”)

9,120(29’ 11”)

8,940(29’ 4”)

5,480(17’ 12”)

5,360(17’ 7”)

4,560(14’ 12”)

10,300(33’ 10”)

7,390(24’ 3”)

2,870(9’ 5”)

2,400(7’ 10”)

9,530(31’ 3”)

9,360(30’ 9”)

5,890(19’ 4”)

5,770(18’ 11”)

4,990(16’ 4”)

10,670(35’ 0”)

7,740(25’ 5”)

2,670(8’ 9”)

5,650 (18’ 6”)

3,650 (12’ 0”)

4,440 (14’ 7”)

1,060 (3’ 6”)

2,800 (9’ 2”)

2,770 (9’ 1”)

2,530 (8’ 4”)

2,920 (9’ 7”)

480 (1’ 7”)

2,000 (6’ 7”)

500(20”)

2,500(8’ 2”)

600(24”)

2,600(8’ 6”)

2,000(6’ 7”)

9,620(31’ 7”)

3,050(10’ 0”)

2,400(7’ 10”)

9,550(31’ 4”)

3,000(9’ 10”)

700(28”)

2,700(8’ 9”)

5,650 (18’ 6”)

7

DIMENSIONS R220LC-9A HIGH WALKER

WORKING RANGES R220LC-9A HIGH WALKER



mm (ft · in)

Boom length

Arm length

Overall length


Track shoe width

Overall width

Boom length

Arm length

Max. digging reach


Max. digging depth



Max. digging height

Max. dumping height


Tumbler distance



Tail swing radius

Rear-end length




Track gauge

A

B

C

D

D’

E

F

G

H

I

J

K

L

A

A’

B

B’

C

D

E

F

3,650 (11’ 12”)

4,440 (14’ 7”)

1,240 (4’ 1”)

2,840 (9’ 4”)

2,770 (9’ 1”)

2,740 (8’ 12”)

3,100 (10’ 2”)

660 (2’ 2”)

2,790 (9’ 2”)

2,000(6’ 7”)

2,400(7’ 10”)

2,920(9’ 7”)

3,900(12’ 10”)

9,140 (29’ 12”)

9,500(31’ 2”)

9,980(32’ 9”)

10,910(35’ 10”)

8,920(29’ 3”)

9,290(30’ 6”)

9,820(32’ 3”)

10,730(35’ 2”)

5,630(18’ 6”)

6,010(19’ 9”)

6,550(21’ 6”)

7,530(24’ 8”)

5,390(17’ 8”)

5,820(19’ 1”)

6,380(20’ 11”)

7,390(24’ 3”)

5,090(16’ 8”)

5,630(18’ 6”)

6,100(20’ 0”)

7,050(23’ 2”)

9,330(30’ 7”)

9,530(31’ 3”)

9,780(32’ 1”)

10,300(33’ 10”)

6,520(21’ 5”)

6,710(22’ 0”)

6,960(22’ 10”)

7,480(24’ 6”)

3,750(12’ 4”)

3,740(12’ 3”)

3,740(12’ 3”)

3,650(11’ 12”)

5,680 (18’ 8”)

2,000(6’ 7”)

9,650(31’ 8”)

3,290(10’ 10”)

2,400(7’ 10”)

9,550(31’ 4”)

3,170(10’ 5”)

2,920(9’ 7”)

9,470(31’ 1”)

3,060(10’ 0”)

3,900(12’ 10”)

9,560(31’ 4”)

3,450(11’ 4”)

5,680 (18’ 8”)

3,395(11’ 2”)

3,495(11’ 6”)

3,595(11’ 10”)

3,505(11’ 6”)

Triple grouser

700 (28”) 800 (32”)

Double grouser

710 (28”)

Type

Width 600 (24”)

8

R220LC-9A Rating over-front Rating over-side or 360 degrees

Lifting Capacities

Boom : 5.68 m (18’ 8”) / Arm : 2.0 m (6’ 7”) / Bucket : 0.92 m3 (1.20 yd3) SAE heaped / Shoe : 600 mm (24”) triple grouser

Load pointheightm (ft)

Load radius At max. reachCapacity Reach

GroundLine




GroundLine




GroundLine

1. Lifting capacity is based on SAE J1097, ISO 10567.2. Lifting capacity of the Robex Series does not exceed 75% of the tipping load with the machine on firm, level ground or 87% of full hydraulic capacity.

3. The load point is a hook located on the back of the bucket.4. (*) indicates the load limited by hydraulic capacity.

9

Lifting CapacitiesR220LC-9A Rating over-front Rating over-side or 360 degrees




GroundLine

R220LC-9A HIGH WALKER Rating over-front Rating over-side or 360 degrees




GroundLine




GroundLine

10

R220LC-9A HIGH WALKER Rating over-front Rating over-side or 360 degrees

Lifting Capacities




GroundLine




GroundLine




GroundLine

11

Lifting CapacitiesR220LC-9A HIGH WALKER Rating over-front Rating over-side or 360 degrees




GroundLine

R220LC-9A LONG REACH Rating over-front Rating over-side or 360 degrees

Boom : 8.2 m (26’ 11”) / Arm : 6.3 m (20’ 8”) / Bucket : 0.52 m3 (0.68 yd3) SAE heaped / Shoe : 800 mm (32”) triple grouser with 5,300 kg (11,680 lb) Counterweight



GroundLine



12

R220NLC-9A MONO BOOM Rating over-front Rating over-side or 360 degrees

Lifting Capacities




GroundLine




GroundLine




GroundLine



13

R220NLC-9A / HYDRAULIC ADJUSTABLE BOOM Rating over-front Rating over-side or 360 degrees

Lifting Capacities




GroundLine




GroundLine



www.hyundai.eu EN - 2013.11 Rev 0

STANDARD EQUIPMENT R220LC-9A / R220NLC-9A

ISO Standard cabinAll-weather steel cab with 360° visibilitySafety glass windowsRise-up type windshield wiperSliding fold-in front windowSliding side window (LH)One key fits all lockable doorsHot & cool boxStorage compartment & AshtrayRadio / MP3 Player with remote control and USB-input Handsfree mobile phone system with USB-charging device Transparent cabin roof-cover12 volt power outlet (24V DC to 12V DC converter)Sun visorRain guard - front window

Computer aided power optimization (CAPO) system3-power modes, 2-work modes, User modeAuto & one-touch deceleration systemAuto warm-up systemOverheat prevention system

Automatic temperature controlAir conditioner & heaterDefroster

Self-diagnostics systemStarting Aid (air grid heater) for cold weatherCentralized monitoring

LCD displayEngine speed or Trip meterClockGauges- Fuel level gauge- Engine coolant temperature gauge- Hyd. oil temperature gaugeWarning lamps- Engine warning- Overload- Communication error- Low battery- Air filter clogging Indicators- Max power- Low speed/High speed- Fuel warmer- Auto decelerationRearview camera

Door and cab locks, one keyThree outside rearview mirrorsMechanical suspension seat with heater Adjustable joysticksConsole box tilting systemFour front working lightsElectric hornBatteries (2 x 12V x 100 AH)Battery master switchRemovable clean-out screen for coolersAutomatic swing brakeFuel pre-filter with fuel warmerBoom holding systemArm holding systemTrack shoes (600 mm; 24”)Track rail guardAccumulator for lowering work equipmentLower frame under coverViscous fan clutchFuel filler pump (50 ℓ/min)Safety lock valve for boom cylinder with overload warning deviceDouble-acting piping kit (clamshell, etc.)Travel alarm

Boom5.68 m; 18’ 8”

Arm2.92 m; 9’ 7”

Cabin ROPS (ISO 12117-2)ROPS (Roll Over Protective Structure)

Hi-mate (Remote Management System)

OPTIONAL EQUIPMENT R220LC-9A / R220NLC-9A

Beacon lampSafety lock valve for arm cylinderSingle-acting piping kit (breaker, etc.)Quick couplerBoom - R220LC-9A

5.68 m; 18’ 8” - Heavy duty8.2 m; 26’ 11” - Long reach

Boom - R220NLC-9A5.65 m; 18’ 6”5.65 m; 18’ 6” - hydraulic adjustable

Arm - R220LC-9A2.0 m; 6’ 7”2.4 m; 7’ 10”2.92 m; 9’ 7” Heavy duty3.9 m; 12’ 10”6.3 m, 20’ 8” Long reach

Arm - R220NLC-9A2.0 m; 6’ 7”2.4 m; 7’ 10”2.92 m; 9’ 7” - not for hydraulic adjustable boom

Cabin FOPS/FOG (ISO/DIS 10262 Level II)FOPS (Falling Object Protective Structure)FOG (Falling Object Guard)

Cabin guard frontWire netFine net

Cabin roof-steel coverCabin lightsTrack shoes - R220LC-9A

Triple grousers shoe (700 mm; 28”)Triple grousers shoe (800 mm; 32”)Triple grousers shoe (900 mm; 36”)Double grousers shoe (700 mm; 28”)Full track rail guard (High walker only)

Track shoes - R220NLC-9ATriple grousers shoe (500 mm; 20” )Triple grousers shoe (600 mm; 25” )Triple grousers shoe (700 mm; 28” )

Additional lower frame - reinforced under coverSeat

Adjustable air suspension seatAdjustable air suspension seat with heaterMechanical suspension seat

Pattern change valve (2 patterns)Air compressor

* Standard and optional equipment may vary. Contact your Hyundai dealer for more information. The machine may vary according to international standards.

* The photos may include attachments and optional equipment that are not available in your area.

* Materials and specifications are subject to change without advance notice.* All imperial measurements rounded off to the nearest pound or inch.

PLEASE CONTACT

Documents

Specifications R220LC-9A / R220NLC-9A...1 ENGINE MODEL CUMMINS QSB6.7 Type Water cooled, 4 cycle Diesel, 6-Cylinders in line, direct injection, turbocharged, charged air cooled and