Xtreme cover1 - 165.22.183.63165.22.183.63/media/assets/manuals/SKB650-2009.pdf · Belt Driven Leaf Collector SKB700/650SKB700/650 ODB Company 5118 Glen Alden Drive Richmond, VA 23231

Belt Driven Leaf CollectorBelt Driven Leaf CollectorSKB700/650SKB700/650

ODB Company5118 Glen Alden DriveRichmond, VA 23231

800-446-9823www.leafcollector.com

Owner's ManualSafety Manual

Pre-Operating ManualOperating Manual

Maintenance ManualService ManualParts Catalog

Administrator

405250

800-446-9823

ODB COMPODB COMPODB COMPODB COMPODB COMPANYANYANYANYANY

IMPROPER USE OF ANY MACHINE CANRESULT IN SERIOUS INJURY!

STUDY AND FOLLOW ALL SAFETYPRECAUTIONS BEFORE OPERATING OR

REPAIRING UNIT

5118 Glen Alden DriveRichmond, VA 23231

DO NOT ATTEMPT TO OPERATEOR REPAIR

THE LEAF COLLECTOR WITHOUT FIRSTREADING AND UNDERSTANDING THIS

MANUAL

IF YOU HAVE ANY QUESTIONS CONCERNING THEINSTALLATION OR OPERATION OF THIS UNIT, PLEASE CALL

ODB FOR ASSISTANCE BEFORE ATTEMPTING TO REPAIR OROPERATE THE UNIT.

THIS MANUAL IS AN INTEGRAL PART OF THE LEAF COLLECTOR ANDSHOULD BE KEPT WITH THE UNIT WHEN IT IS SOLD.

TABLE OF CONTENTS

Read and understand this entire manual before operating, maintain-ing or repairing the leaf vacuum.

1.0 GENERAL SAFETY1.1 Safety Symbol Definitions1.2 Do’s and Don’t’s1.3 Training1.4 Safety Decal Listing and Part Numbers

2.0 PRE-OPERATING SECTION2.1 Instruments and Controls2.2 Safe Operations2.3 Preparation for Operation2.4 Pre-Transport Checks2.5 Protective Equipment and Clothing2.6 Worksite Preparation

3.0 OPERATING SECTION3.1 Starting Engine3.2 Engaging PTO3.3 Dumping the Body3.4 Vacuuming Leaves

4.0 MAINTENANCE SECTION4.1 Maintenance Overview4.2 Maintenance Interval Chart4.3 Lubrication4.4 Preventative Maintenance4.5 Torque Values4.6 Quick Reference Maintenance Chart

SAFETY, OPERATING AND MAINTENANCETABLE OF CONTENTS

ODB COMPODB COMPODB COMPODB COMPODB COMPANYANYANYANYANY 800-446-9823

TABLE OF CONTENTS


SAFETY, OPERATING AND MAINTENANCETABLE OF CONTENTS, continued;


5.0 SERVICE SECTIONSERVICE AND TROUBLESHOOTING

Service and RepairEngine Electrical TroubleshootingAuto PTO Adjustment GuideHydr. Boom TroubleshootingImpeller Installation/Removal

WIRING DIAGRAMSEngine Wiring DiagramCircuit Board WiringTrailer Wiring DiagramBoom Pump Wiring Diagram

HOIST HYDRAULIC SYSTEMHydraulic Valve - 4 wayHydraulic System DiagramHoist Tips

6.0 PARTS BREAKDOWNSENGINE GROUP

Inst. Panel BreakdownAir Cleaner AssemblySheet Metal AssemblyEngine ExhaustRadiator AssemblyRemote Throttle Ass’y (OPTIONAL)Chaffe Eleminator (OPTIONAL)

CLUTCH GROUPClutch BreakdownAuto PTO BreakdownAuto PTO LinkageClutch Assist Breakdown

6.0 PARTS BREAKDOWNS, cont.;BLOWER HOUSING GROUP

Blower Housing FaceBelt Drive Group (OPTIONAL)Imp. & Blr Housing Breakdown

CHASSIS AND HOPPER GROUPFuel Tank AssemblyHydraulic Tank AssemblyTop Screen AssemblyTongue AssemblyLight and Reflector GroupChassis/Body Prop GroupRear Door Hardware

TIRE AND AXLE GROUP14 CY - 8K Axle Group20 CY - 6K Axle Group20/25/30 CY 10/12K Axle Group25/30 CY 9K Axle GroupBrake AssemblyAxle Hub Assembly

HOSE BOOM GROUPHose Boom AssemblyIntake Hose AssemblyHydraulic Pump Assembly

1.0 GENERAL SAFETY


1.0 GENERAL SAFETY1.1 Safety Symbol Definitions1.2 Do’s and Don’t’s1.3 Training1.4 Safety Decal Listing and Part Numbers

1.0GENERALSAFETY


SAFETY PRECAUTIONS

!

The purpose of safety symbols are to attract your attention to possibledangers. The safety symbols, and their explanations, deserve your carefulattention and understanding. The safety warnings do not by themselveseliminate any danger. The instructions or warnings they give are notsubstitutues for proper accident prevention measures.

SYMBOL MEANINGSAFETY ALERT SYMBOL: Indicates danger, warning or caution.Attention is required in order to avoid serious personal injury. May be usedin conjuction with other symbols or pictographs.


Disregarding this safety warning WILL result in serious equipmentdamage, injury or possible death.

Disregarding this safety warning CAN result in serious equipmentdamage, injury or possible death.

Disregarding this safety warning MAY result in minor or moderateinjury or property damage.

1.1 SAFETY SYMBOL DEFINITIONS:

This manual provides the owners/operator with procedures for safe opera-tion, maintenance and repair of ODB’s leaf collectors. As with any ma-chine, there are hazards associated with their operation. For this reasonsafety is emphasized throughout this manual. To highlight specific safetyinformation the following safety definitions are provided to assist thereader.


SAFETY PRECAUTIONS

DO NOT operate, maintain or repair this unit without having fully readand understood ALL the aspects of this manual.DO NOT ride, sit or stand on unit at anytime.DO NOT modify the leaf vacuum for any reasons to allow for riders.DO NOT operate the unit in a state of disrepair.DO NOT operate the unit with ANY guards or safety devices broken,missing, or inoperable.DO NOT operate the unit without wearing proper safety equipment.DO NOT operate this unit while under the influence of any alcohol ormedication.DO NOT operate this unit if you have a record of mental instability ordizziness which could result in injury to yourself or others.DO NOT operate this unit if you are under 18 years of age.DO NOT operate this unit without fully inspecting the unit for any dam-age or leakage.DO NOT operate if the unit has any excessive vibration.DO NOT operate unit with the inspection door limit switch damaged ormissing.DO NOT operate unit unless all hydraulic components such as hoses andfittings have been checked for leakage or damage.DO NOT operate unit unless it is properly attached to the tow vehicle.DO NOT tow unit without using all the safety chains.DO NOT tow unit with a damaged tongue.DO NOT fill fuel tank with engine running. Allow engine to cool for 5 min-utes before refueling.DO NOT operate unit if fuel is spilled or with fuel cap off.DO NOT smoke or weld near the unit.DO NOT run engine in an enclosed area.DO NOT place hands or feet near moving or rotating parts.DO NOT operate engine with an accumulation of grass, leaves or otherdebris on the engine.


1.2 DO’S AND DO NOT’S:

This section contains some general safety precautions to do and not to do.This is not an all inclusive list and and it is the responsibilty of the operatorto have proper training and use common sense in work situations.

1.

2.3.4.5.

6.7.

8.

9.10.

11.12.

13.

14.15.16.17.

18.19.20.21.22.

DO NOT:


SAFETY PRECAUTIONS

DO NOT run engine with air cleaner removed.DO NOT leave leaf machine unattended while in operation.DO NOT park machine on steep grade or slope.DO NOT vacuum a leaf pile without looking for foreign objects such asmetal, glass, plastic or large pieces of wood.DO NOT go under raised body without body prop in place for any reason.DO NOT collect leaves without the dump body lowered completely.DO NOT collect leaves with the rear doors open.DO NOT raise dump body near any power lines or low tree branches.DO NOT raise dump body on an uneven or soft surface.DO NOT lower dump body without a complete visual check of the bodyarea.DO NOT raise dump body without wheel chocks placed under the wheels.

23.24.25.26.

27.28.29.30.31.32.

33.

DO NOT, continued;

DO’s:

DO completely read and understand the owner’s manual before operat-ing, maintaining or repairing the leaf collector.DO follow engine and PTO manufacturer operating and maintenanceinstructions.DO check fuel lines and fittings frequently for cracks or leaks. Replaceif necessary.DO completely inspect the unit before leaving the service garage.DO check the tow tongue each day for cracks.DO inspect and be attentive to what is being vacuumed.DO check the impeller, liners and blower housing for cracks or holesdaily.DO remove the negative battery cable before doing any maintenanceon the unit.DO wear proper safety equipment as described in this manual.DO watch for pedestrians, animals and other foreign material whenvacuuming leaves.DO replace any worn or missing safety stickers immediately.DO insert the body prop before going under the raised body for any rea-son.

1.

2.

3.

4.5.6.7.

8.

9.10.

11.12.


SAFETY PRECAUTIONS

Improper use of the ODB leaf collector CAN result in severe per-sonal injury or death. All personnel using this leaf vacuum must betrained and qualified with all the operations, maintenance, repairand safety procedures defined in this manual.

1.3 TRAINING:

The warnings and procedures regarding safety in this manual are to beused as a guideline only. It is impossible to cover all the events that couldhappen in the vacuuming process. For this reason, it is vital that theowner accept the responsibility to implement a training program that willprovide every operator or mechanic the basic skills and knowledge tomake good judgement in all situations.

This training program must include the entire scope of hazards, precau-tions and government regulations encountered in the vacuuming process.The program should stress the need for regularly scheduled preventivemaintenance and detailed equipment safety checks.

ODB strongly recommends all training programs be documented to ensureall operators and mechanics receive initial training on not just the opera-tion but the safety features of the leaf collector.


Danger--Do Not Open Cover While in OperationDanger--Do Not Ride, Sit or Stand on UnitDanger--Head, Eye and Ear Protection RequiredLCT60C Leaf Collector stickerDo Not Over-Lubricate bearingsUse Diesel OnlyDanger--FlammableDo Not Engage PTO over 1,000 RPMDanger--Rotating PartsDanger--Explosion HazardDanger--Check Impeller and Liners Daily for WearDanger--Inspect Tow Bar for DamageWarning--Check Lug nutsODB leaf collection systems stickerThrottle decalSafety Shut off-Ignition decal

1.2.3.4.5.6.7.8.9.

10.11.12.13.14.15.16.

ITEMNO.

PARTNUMBER DESCRIPTION

200182200179200181200221200109200055200177200059200183200178200189200180200104200061200120200112

Decals shown at end of section 1.4

1,3,11,9

3,4,8,11,14,15,16

2,3,4,6,7,10,12,

13

SAFETY PRECAUTIONS1.4 SAFETY DECALS - LCT60C:

Danger--Do Not Open Cover While in OperationDanger--Do Not Ride, Sit or Stand on UnitDanger--Head, Eye and Ear Protection RequiredLCT600 Leaf Collector stickerDo Not Over-Lubricate bearingsUse Diesel OnlyDanger--FlammableDo Not Engage PTO over 1,000 RPMDanger--Rotating PartsDanger--Explosion HazardDanger--Check Impeller and Liners Daily for WearDanger--Inspect Tow Bar for DamageWarning--Check Lug nutsODB leaf collection systems stickerThrottle decalSafety Shut off-Ignition decal

1.2.3.4.5.6.7.8.9.

10.11.12.13.14.15.16.

ITEMNO.


200182200179200181200221200109200055200177200059200183200178200189200180200104200061200120200112


LH Side5,6,7Inside Pedestal(2 of each)

1,9,6on outsideof lid

11

11312

1

8

13 13

104,3,2

RH Side

Front Rear

14

15

16

SAFETY PRECAUTIONS1.4 SAFETY DECALS, continued - LCT600/6000

Danger--Do Not Open Cover While in OperationDanger--Do Not Ride, Sit or Stand on UnitDanger--Head, Eye and Ear Protection RequiredLCT650 Leaf Collector stickerDo Not Over-Lubricate bearingsUse Diesel OnlyDanger--FlammableDo Not Engage PTO over 1,000 RPMDanger--Rotating PartsDanger--Explosion HazardDanger--Check Impeller and Liners Daily for WearDanger--Inspect Tow Bar for DamageWarning--Check Lug nutsODB leaf collection systems stickerThrottle decalSafety Shut off-Ignition decal

1.2.3.4.5.6.7.8.9.

10.11.12.13.14.15.16.

ITEMNO.


200182200179200181200221200109200055200177200059200183200178200189200180200104200061200120200112


1,3,11,9

3,4,8,9,11,15,16

2,3,4,6,7,10,12

13,14

1,5,9

SAFETY PRECAUTIONS1.4 SAFETY DECALS, continued - LCT650

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

SAFETY PRECAUTIONS1.4 SAFETY DECALS - Decal Layout for LCT60C/600/650/6000


2.0 PRE-OPERATING SECTION2.1 Instruments and Controls2.2 Safe Operations2.3 Preparation for Operation2.4 Pre-Transport Checks2.5 Protective Equipment and Clothing2.6 Worksite Preparation

2.0Pre-Operating

Section

2.0 PRE-OPERATING SECTION


Pre-Operating Section

2.1 INSTRUMENTS AND CONTROLS:

Ignition Switch:Used to power the accessories and start the unit. Unitwill not start without Murphy switch depressed.ACCESSORIES - first positionSTARTER ENGAGE - second position (springs return tofirst position)

Murphy Switch:This switch overrides the low oil pressure and high tem-perature cutoff control. This switch must be depressedbefore the starter engages. After the engine starts, waitfor oil pressure to rise before releasing the button.

Throttle:This control provides positive locking and vernier adjust-ment of engine.

Tachometer:This gauge indicates the engine r.p.m’s. The sender islocated on the engine block

Volt Meter:The gauge shows the status of the engine chargingsystem. When the charging system is operating properlyit should read approximately 14 volts. If the gauge readsbelow 13 volts, the alternator is not charging the batteryand the system should be checked by a qualifiedtechnicican.

Oil Pressure Gauge:Confirms and indicates the presense and pressure ofengine oil. If the gauge reads low, it should be checkedby a qualified technician.

Engine Temperature:Indicates the engine coolant temperature. If the gaugereads over 240 degrees the unit should be checked by aqualified technician.

Hour Meter:Indicates the accumulated hours of the the engine. Thisshould be used to schedule maintenance.

oil press. gauge

water temp gauge

fuel gauge

hour meter

tachometer

volt meterMurphySwitchIgnitionSwitch

strobe switch

(Typical)

Always make sure the PTO isdisengaged before starting unit.

throttle



ALL personnel using, maintaining or servicing this unit must betrained in all safety procedures outlined in this manual. Improper orcareless use of this equipment CAN result in personal injury ordeath.

2.2 SAFE OPERATIONS:

Operations shall be restricted to:


Properly trained, qualified and experienced operators and/or qualifiedand experienced maintenance and test personnel.

Trainees under the direct supervision of qualified and experiencepersonnel.

Qualified and experienced maintenance and service personnel.

1.

2.

3.

Operators who qualify to operate this equipment under the aboverestrictions shall also comply with the following physical require-ments:

Have good vision and the ability to read and understand this manualas well as all safety and operational decals on the equipment.

Be capable of hearing, with or without a hearing aid, at a levelneeded to safely operate this equipment.

A record of mental stability with no history of epileptic seizures, dizzi-ness, or any other disability that may result in injury to himself orothers.

If any of these requirements are not satisfied at any time, the personfailing to meet these requirements MUST NOT OPERATE THISEQUIPMENT.

1.

2.

3.



2.2 SAFE OPERATIONS (continued):

Additional Requirements:

Each operator must demonstrate competence to understand all safetydecals, operator’s manuals, safety codes, applicable governmentregulations, and all other information applicable to the safe andproper operation of the leaf vacuum.

Each operator must demonstrate the ability to recognize an emer-gency situation that may arise during vacuuming operations and theknowledge and procedures to implement corrective action.

Each operator must demonstrate or provide evidence ofqualificatation and experience prior to operating the leaf vacuum.

Each operator must be able to recognize existing or potential prob-lems regarding the mechanical integrity of the leaf vacuum and reportany maintenance requirements to the supervisor in charge.

Each operator must wear the proper personal clothing and safetygear. (Refer to SAFETY PRECAUTIONS Section 5.4)

Operators must not be physically or mentally fatigued.

Operators must not be under the direct or indirect influence of alcoholand/or drugs. This includes prescription drugs that could causedrowsiness, dizziness, or any other condition that would impair theirability to operate or use this equipment in a safe manner.

1.

2.

3.

4.

5.

6.

7.


Before your leaf vacuum is put into operation it is very important toread and follow the procedures outlined in the engine owner’smanual. (EOM).

2.3 PREPARATION FOR OPERATION


For specific information regarding the following checks please refer tothe “Maintenance” section of this manual and the engine owner’s manual.

IMPORTANT CHECKS:

1.2.3.4.5.6.

7.

8.

9.

10.

DISENGAGE the clutch and remove the negative battery cable be-fore performing the following checks.

NEVER place any part of the body under or behind guards or anyother area in which you cannot see.

NOTE: The following checks contained in the next three sectionsshould be performed prior to leaving the storage area.

Check engine fuel, coolant and oil levels. (see EOM)Check engine air filterCheck all bolts and nuts to ensure they are tight.Check all controls for free and proper operation.Check main drive belt (if equipped) for proper adjustment.Inspect the fan blades to ensure that they are not bent , deformed,fatiqued or cracked.Inspect the intake hose flange to make sure it is connected correctlyto the blower housing.Inspect the leaf vacuum frame and structure for any bent, broken,cracked, missing or loose parts.Check all guards to ensure they are undamaged, in place and prop-erly secured.All decals must be in place and legible prior to operating the leafvacuum. See the decal section for decal replacement.


Failure to properly hitch the leaf vacuum to the tow vehicle, verifythe road worthiness of the leaf vacuum and the tow vehicle andverify all equipment is properly stowed, may cause serious injury ordeath to yourself or others.

TOW VEHICLE MUST have proper towing capacity for the leafvacuum being towed. Check the tow vehicles operating manual forrated capacity.

Do not tow the leaf vacuum unless all important checks listed beloware completed.

2.4 PRE-TRANSPORT CHECKS


IMPORTANT CHECKS:

1.

2.

3.

4.

5.

Hitch is properly secured to tow vehicle and hose boom secured. a. Frame must be level or the tongue slightly lower than the rear

of the leaf vacuum while towing to ensure proper weightdistribution. The hitch may have to be adjusted when towingwith vehicles of varying tow hitch height.

Safety chains installed correctly. a. Chains routed under trailer tongue in an “X” pattern between

tow vehicle and trailer. b. Slack in chain should be adjusted to permit turning but should

not be dragging on the ground.

Connect trailer wiring to the tow vehicle and ensure that all trailerlighting is operating properly.

Ensure that the safety breakaway switch is functioning properly andattached securely to the tow vehicle. Allow enough slack to ensurethat vehicle turns will not activate the safety breakaway switch.NOTE: Follow manufacturers procedure to ensure tow vehicles brakecontrol box is properly adjusted.

Check the general condition of the tires, tire pressure and ensure thatall lugnuts are securely fastened.

Pre-Operation Section


2.4 PRE-TRANSPORT CHECKS (continued):

IMPORTANT CHECKS (continued):

Visual examination of the leaf vacuum frame, suspension and struc-ture to determine if all components are correctly positioned andsecured for travel.

Check the intake hose boom to verify that it is securely fastened tothe leaf vacuum and can not swing free.

Verify there are no loose tools or materials on the trailer, inside theintake and exhaust hoses, or inside the engine sheet metal.

Check all cones, wheel-chocks, signs or other support tools andmaterials to ensure proper stowage.

Verify the driver of the tow vehicle is qualified to tow the type andweight of the unit.

6.

7.

8.

9.

10.


2.5 PERSONAL PROTECTIVE EQUIPMENT AND CLOTHING


IMPORTANT CHECKS:

Anyone operating ODB’s leaf vacuums MUST wear appropriateprotective equipment and clothing to protect them from injury duringoperations.

1.

2.

3.

4.

5.

6.

7.

Head Protection: Hard hats without under-chin strapping.

Eye Protection: Wraparound goggle type eye protection held inplace with an elastic band around the head or a hard hatmounted face shield, which provides full protection of the face.Eye protection must meet ANSI Z87.1 standards.

Hearing Protection: plug type or “muff type” ear protectionshould be worn at all times while operating the unit.

Breathing Protection: Paper filter type dust masks should beworn to protect from dirt and dust particles during the vacuumingprocess.

Reflective Vests: Highly visible vests should be worn so motor-ists can see see the operator in all weather and lighting condi-tions.

Work Gloves: Gloves should be worn to protect the hands andwrists from debris.

Steel Toed Boots: should be worn to protect the feet.

Work clothes MUST be close fitting, but not restrictive of move-ment, without any loose parts that could be entangled in any partsof the leaf vacuum. This includes items such as jewelry, chainsand backpacks.

PROTECTIVE EQUIPMENT:

Always wear proper safety equipment as outlined below, not wear-ing such equipment CAN result in serious personal injury or pos-sible death.


2.6 WORK SITE PREPARATION


1.

2.

3.

4.

5.

6.

7.

An inspection of the leaves to be vacuumed must be done prior tothe vacuuming process. We realize that it is impossible to com-pletely inspect every inch of leaves being vacuumed, but it isimperative that all leaves be inpsected for obvious dangerousmaterial before vacuuming.

The operator should never be in the line of traffic, the operatorshould work on the shoulder whenever possible.

The operators should place cones or other barriers to provideadequate warnings to vehicles and pedestrians that vacuumingis in progress.

Strobe lights on the leaf vacuum and on the tow vehicle should beon at all times for high visibility.

Confirm that all operators are wearing proper clothes and per-sonal protective equipment.

Restrict all personnel, except the operator from the area near theleaf vacuum. DO NOT allow pedestrians, children or animalsnear the work area.

Make sure that the exhaust hose fits properly into the box con-tainer so that all debris is blown into the box container.

The following guidelines must be followed to insure safety.

Never place any part of the body under or behind guards or anyother visually obscured area.

Making sure the leaves are clear of possible dangerous material iscritical to safe vacuuming. Vacuuming up metal, glass, rocks orother dangerous material CAN cause serious damage to the equip-ment or personal injury.

3.0 OPERATING SECTION


3.0 OPERATING SECTION3.1 Starting Engine3.2 Engaging PTO3.3 Vacuuming Leaves


Operating Section

3.1 Starting Engine

Review the Engine Operating Manual supplied with yourleaf vacuum for specific start-up, maintenance and oper-ating instructions. It is especially important to reviewbreak-in service procedures for brand new units.

oil press. gauge

water temp gauge

fuel gauge

hour meter

tachometer


strobe switch

(Typical)

Always make sure the PTO is disengaged beforestarting unit. (See figure 3b)throttle


PTO shown disengaged

Thoroughly read and understand the safety andpre-operating sections of this manual before star-ing the engine.

figure 3b

figure 3a

Perform all the pre-starting, pre-operating checksoutlined in the EOM and in this manual.

Make sure the PTO is disengaged as shown infigure 3b.

Turn the throttle control (fig. 3a) counter-clock-wise 2 revolutions.

Depress and hold the Murphy switch while start-ing.

DO NOT start the engine in an enclosed building.Proper ventilation is required before starting theengine.

Starting Procedure (refer to figures 3a and 3b):

1.

2.

3.

4.

800-446-9823

3.1 Starting Engine, continued;

IMPORTANT: Do not operate the starter formore than 30 seconds at a time. To do somay overheat the starter. If the engine doesnot start the first time, wait at least 2 minutesbefore trying again. If the engine fails to startafter 4 attempts, see the trouble shootingsection of the EOM and this manual.

Pull the ignition switch all the way out, when theengine starts release the ignition switch. Itshould spring back to the first position.

IMPORTANT: If the ignition switch is releasedbefore the engine starts, wait until the starterand the engine stop turning before tryingagain. This will prevent possible damage tothe starter and/or flywheel.

After the engine starts, continue to hold theMurphy Switch in until the oil pressure gaugereads at least 15 psi. The Murphy shut off switchwill not allow the engine to operate below thislevel. If the gauge does not rise above 15 psiwithing 5 seconds, stop the engine and determinethe cause. Normal operating oil pressure is 50psi with oil at normal operating temperature.

Check all gauges for normal engine opreration. Ifoperation is not normal, stop the engine anddetermine the cause.

IMPORTANT: To assure proper lubrication,operate the engine at or below 1200 rpm withno load for 1 -2 minutes. Extend this period 2- 4 minutes when operating at temperaturesbelow freezing.

Watch the coolant temperature gauge. Do notplace engine under load until it is properlywarmed up. The normal engine coolant tempera-ture range is 180 - 202 degrees F.

5.

6.

7.

8.

.

oil press. gauge

water temp gauge

fuel gauge

hour meter

tachometer


strobe switch

(Typical)

throttle

figure 3a


Operating Section

Operating Section

3.2 Engaging the PTO

Review the Engine Operating Manual supplied with yourleaf vacuum for specific start-up, maintenance and oper-ating instructions. It is especially important to reviewbreak-in service procedures for brand new units.



Thoroughly read and understand the safety andpre-operating sections of this manual before star-ing the engine.

figure 3b

Perform all the pre-starting, pre-operating checksoutlined in the EOM and in this manual.

Start the engine as previously discussed in thismanual and in the EOM.

Once the engine has been allowed to thoroughlywarm up (engine temperature gauge should readat least 180 degrees) pull the throttle control untilthe engine reaches 1000 rpm.

Grasp the PTO handle (fig. 3b) and slowly push thehandle forward. NOTE: Most of ODB’s units havea PTO assist cylinder which engages the PTO at aspecific speed in order to properly engage thePTO. Because of this the PTO handle only needsto be raised slightly, then the assist cylinder willtake over and engage the PTO automatically. (fig.3c)

Engaging the PTO (refer to figures 3b and 3c ):

1.

2.

3.

4.

800-446-9823

Make sure the intake hose is properly attachedand make sure the front of the hose is clear ofany objects which could be inadvertently vacu-umed during the PTO engagement process.

figure 3c

safety assist cylinder

PTO handle

3.2 Engaging the PTO, continued;

IMPORTANT: If the unit experiences anyheavy vibrations or makes any unusualnoises, shut the engine down and after follow-ing the necessary safety guidelines, have aqualified technician investigage the cause.DO NOT operate a unit that is in a state ofdisrepair.

If the unit is running smoothly and does notdispaly any excessive vibration, the unit is readyto vacuum leaves. NOTE: Please see the nextsection before vacuuimg leaves.

The unit is fully engaged when the PTO handle ispointing to the right. It is fully disengaged when thehandle is pointing straight up.

5.


Operating Section

Disengaging the PTO (refer to figures 3b and 3d):

Decrease the rpm to 1000 rpm.

Grasp the PTO handle and slowly disengage thePTO.

When the PTO is fully disengaged, the enginecan be shut down.


figure 3b

PTO handle

1.

2.

3

Operating Section

3.3 Vacuuming Leaves


Thoroughly read and understand the safety, pre-operating and oper-ating sections of this manual before vacuuming. Wear the propersafety equipment as outlined in this manual.

Start the engine and engage the PTO using the procedures statedearlier in this manual.

Set the engine throttle to around 1200 rpm.

NOTE: Always vacuum leaves using the lowest rpm as possible.This saves fuel and decreases the amount of dust escaping the boxcontainer.

Lower the intake hose to a few inches above the leaf pile. Hold theintake nozzle at a 45 degree angle to allow proper air flow. Thisshould allow the leaves to be vacuumed. DO NOT bury the intakenozzle into the leaf pile, this will cut off the air flow and will makevacuuming much more difficult and increase the chance of clogging.

If the leaves are not vacuuming, increase the rpm to 1400 and tryvacuuming at this setting.

NOTE: Wet leaves will need higher rpm’s to vacuum whereas dryleaves will only need minimal rpm’s.

Continue moving the nozzle in a sweeping motion above the leaveswhile vacuuming.

Vacuuming Leaves:

1.

2.

3.

4.

5.

800-446-9823

Make sure the exhaust hose is connected to the box containerproperly before vacuuming leaves. Visually inspect the leavesbefore vacuuming for any material that could be harmful to the leafvacuum or people. This includes bottles, wood, steel, glass, stoneor other hard or breakable objects.


4.0 MAINTENANCE SECTION4.1 Maintenance Overview4.2 Maintenance Interval Chart4.3 Lubrication4.4 Preventative Maintenance4.5 Torque Values4.6 Quick Reference Maintenance Chart

4.0MAINTENANCE

SECTION

4.0 MAINTENANCE SECTION


Maintenance Section

4.1 MAINTENANCE OVERVIEW:

A properly maintained leaf vacuum will dramatically extend the life of theunit and will create a safer work place as well. For the general safety andwelfare of all personnel it is important to create a scheduled maintenanceprogram that covers all the elements in this manual as well as the engine,PTO and axle owner’s manuals provided with this unit.

Use the chart on the following page as a guide for your scheduled mainte-nance program. If there are any questions concerning any ot these proce-dures please call ODB.


Only properly trained personnel should perform maintenance orrepair on this equipment. Consult ODB before performing anymaintenance procedures that is not specificially covered in thismanual. Improper maintenance or repair may void any and all war-ranties on this equipment.

Improper maintenance or repair CAN result in equipment damageand/or personal injuries.

BEFORE CONTINUING, please read and understand the Safety, Pre-operating and Operating sections of this manual before doing anyprodcedures in this section.

80 Hours/2 WeeksItem

Daily/10 hrs

40 Hours/Week

Check Engine Oil LevelCheck Coolant LevelCheck Fuel Filter Sediment BowlLubricate Main Shaft Bearings (about 2 oz.)Lubricate PTO BearingsCheck Air Intake FilterCheck/Clean Pre-FilterCheck Lug Nuts and Tire Pressure/ConditionInspect Radiator for leaks and trash Buildup. Clean radiator screenCheck Engine as Described in the Engine Owner's ManualInspect Exterior of Blower Housing for DamageCheck Trailer Brake Lights and Turn SignalsCheck Power Band For Proper Alignment, Wear, and Tightness (if equipped)Inspect Impeller For DamageCheck All Nuts and Bolts For TightnessCheck Tow Bar For Damage or WearCheck Bolt Hole Where the Tongue and Trailer Bed are Connected For WearClean and Check Battery and ConnectionsInspect Intake and Exhaust HosesInspect All Ducts for DamageRemove Blower Housing Face and InspectLiners inside Blower Housing for WearGrease/Inspect Wheel Bearings for Corrosion or WearInspect All Hydraulic and Fuel Lines for Leaks or Wear

(Use Hour Meter as a Guide)This chart is only a reference, always consult the Owners Manual of the Engine, PTO, etc for actual recommendations

Maintenance Section


4.2 MAINTENANCE AND LUBRICATION CHART

Maintenance Section


4.3 LUBRICATION:

The following are general lubrication procedures for ourstandard units. Any special or custom built units mayhave other lubrication procedures not directly mentionedin this manual. Please consult ODB before any lubricat-ing procedures not specifically mentioned in this manual.

Proper lubrication of your unit correlates directly to how longyour unit will last. A properly maintained unit will last muchlonger than a unit that is not maintained properly. NOTE:Always lubricate bearings at the end of each work day.This will displace any moisture in the bearings. Also lubri-cate thorougly before extended shutdown or storage.

Remove the negative battery terminal beforeattempting any lubrication procedures.

Thoroughly read and understand the safety andpre-operating sections of this manual before per-forming any lubrication procedures.

Lubrication Points:

1. Drive Bearings (figure 4.3a): These bearingsare critical components of the belt-driven units.These bearings should be greased every 10 hourswith approximately two strokes from the averagehand pump grease gun. The type of grease usedin these bearings are also critical to the perfor-mance of the bearings. A multi-purpose, heavy-load, high-temperature, moisture resistant #2grease is required for the drive bearings. ODBrecommends LubeMaster Premalube 4234 grease.Other premium quality grease that matches theabove requirements may be used but after years oftesting ODB recommends the Premalube grease.

1

Figure 4.3A

NOTE; DO NOT mix different typesof grease. The old grease MUST BEpurged before a different type ofgrease is used. Mixing grease WILLcause premature failure to the bear-ings.

Lubrication Points, continued;

Trailer Wheel Bearings (figure 4.3b): Most ofODB's units are equipped with "EZ-Lube" greasefittings. This allows the operator to grease thebearings without removing the hubs. The "EZ-Lube" feature consists of axle spindles that havebeen specially drilled and fitted with a grease zerkin their ends (fig. 4.3c). When grease is pumpedinto the zerk, it is channelled to the inner bearingand then flows back to the outer bearing andeventually back out the grease cap hole. Thetrailer wheel bearings should be checked andgreased after the first 30 days of service then atthe beginning of every season.

Grease specifications:

Thickener Point............................Lithium ComplexDropping Point......................230 degr. C minimumConsistency............................................NLGI No.2Additives.........................EP,Corrosion & Oxidation

InhibitorsBase Oil...................Solvent refined Petroleum OilBase Oil Viscosity............@40 deg. C 150cSt Min.Viscosity Index.....................................80 MinimumPour Point...................................-10 deg. Minimum

Approved Sources:

Mobil Oil........................................Mobilgrease HPExxon/Standard......................................Ronex MPKendall Refining...............................Kendall L-427Ashland Oil Co........Valvoline Val-plex EP Grease.Penzoil.......Premium Wheel Bearing Grease 707L

For any questions concerning wheel lubricationplease consult the axle owner's manual suppliedwith your leaf collector or contact ODB.

Figure 4.3b

2.

4.3 LUBRICATION, continued;

Grease fitting is behind rubber plug

Figure 4.3c

Maintenance Section


Maintenance Section


Lubrication Points, continued;

Boom Swivel Bearings (figure 4.3d): Thesebearings are on most of ODB's model LCT600 andLCT6000 after 1996. Grease the boom bearingsonce every week with a multi-purpose moistureresistant #2 grease.

PTO Bearing & PTO Shaft Fitting (figure 4.3e):The PTO bearings should be greased after every50 hours of operation with a high grade, hightemperature lithium base #2 lubricant having anoperating temperature of 200 degrees F. Threeto five pumps with a hand operated grease gun issufficient. NOTE: Units manufactured after 2000may not have a PTO bearing grease fitting.These bearings are sealed and do not requiregreasing.

The PTO crossover shaft and linkage should belubricated with high temperature lithium base #2lubricant after 200 hours of operation.

Hinge and Friction Points: Leaf vacuum opera-tion and longevity can be improved by keepinghinges and friction points lubricated. ODB recom-mends that lubricaton be performed weekly. UseSAE30 weight oil on hinges and a premium grade,high temperature lithium based EP#2 grease onfriction points.

Hitch and Tongue (figure 4.3f):The hitch and hitch ring should be checked andlubricated daily to minimize wear. Apply greaseand/or SAE30 weight oil wherever applicable.

Figure 4.3d

3.

4.

5.

6.

4.3 LUBRICATION, continued;

One fitting on each bearing

Figure 4.3ePTO bearing PTO shaft grease

fitting

Figure 4.3f

Maintenance Section


4.4 PREVENTATIVE MAINTENANCE

The following are general preventative maintenance procedures for our stan-dard units. Any special or custom built units may have other preventativemaintenance procedures not directly mentioned in this manual. Please con-sult ODB before doing any preventative maintenance procedures not specifi-cally mentioned in this manual.

Proper preventative maintenance of your unit, just like lubrication, correlatesdirectly to how long your unit will last. A properly maintained unit will lastmuch longer than a unit that is not maintained properly.

Remove the negative battery terminal before attempting any mainte-nance procedures.

Thoroughly read and understand the safety and pre-operating sec-tions of this manual before performing any maintenance procedures.

Preventative Maintenance:

1.

2.

Engine Oil: Change the oil and oil filter according to schedules pro-vided in your engine's owner's manual (EOM). The engine oil levelshould be checked every day. The level should be checked after theengine has been stopped for a period of time. This will allow the oil todrain back into the oil pan, allowing a better indication of the true oillevel. If the level is low, see the engines owner's manual for the correcttype of oil.

Engine Coolant: Check the coolant level before starting the unit eachday. The coolant level should not be less than one inch below the topof the radiator.

NEVER check the engine coolant when the engine is hot. Allow theengine to cool at least one hour before checking the coolant. Checkthe engine owner's manual for instructions. ALWAYS wear eye andhand protection when working with the radiator.

Maintenance Section


4.4 PREVENTATIVE MAINTENANCE, continued;Preventative Maintenance, continued;

Engine Radiator: The engine radiator on a leaf vacuum becomesclogged with dust and debris frequently because of the nature of thejob. If the radiator is not cleaned properly it WILL cause impropercooling and WILL eventually cause serious damage to your engine.The debris accumulating on the radiator can be lessened by loweringthe RPM on the engine to a level just enough to vacuum the leaves.The higher the RPM the more dust that is put into the air. Also, it maybe necessary to put mesh or tarps on the top of the leaf box containerto reduce the debris and dust. If this is done, make sure there isenough air ventilation on the box so the box is not blown apart.Proper belt condition and coolant mix-ratio, as well as coolant condi-tioners, are all critical to proper engine cooling. See the enginesowner's manual for specifics on coolant mixture ratios and conditioners.The radiator should be inspected and cleaned with compressed air every-day at the very least.

Engine Air Cleaner: Due to the large amounts of dust generated incollection leaves, it is critical to your engine's life that the pre-cleanerand air filter be maintained properly. The pre-cleaner should be cleanedat least daily of any debris that has accumulated. If conditions warrantit should be cleaned more. The air filter should be checked daily andshould be replaced at the first sign of it being dirty. DO NOT attempt toclean the air filter, replace the dirty air filter. It is a good idea to cleanout the air filter housing once a week to clean any dust debris that mayhave accumulated.

Tires and Wheels: Tires and wheel lug nuts should be checked on adaily basis. Tires should be checked for excessive wear and proper airpressure. Check the side wall of the tire for proper inflation pressure.Torque all 1/2" diameter lug nuts from 90 to 120 foot pounds. Torqueall 5/8" diameter lug nuts from 175 to 225 foot pounds. Consult theaxle manufacturers owner's manual for more detailed information.

NEVER attempt to clean or inspect the radiator with the enginerunning or while the engine is HOT. Allow the engine to cool at leastone hour before mantaining the radiator. Check the engine owner'smanual for instructions. ALWAYS wear eye and hand protectionwhen working with the radiator.

3.

4.

5.

Maintenance Section



Trailer Brakes (if equipped): Most of the newer ODB leaf vacuumshave electric brakes on the axle(s). It is critical that these brakes workproperly. The trailer's brakes should be checked daily, before leavingthe equipment yard, for proper operation. The trailer brakes are de-signed to work in synchronization with your tow vehicles brakes. Neveruse your tow vehicle or trailer brakes alone to stop the combined load.The synchronization between the tow vehicle and the leaf vacuum isaccomplished through the brake controller and needs to be set cor-rectly. Please read the brake controllers manual and the axle owner'smanual for these procedures.

The brakes should be adjusted after the first 200 miles of operationwhen the brake shoes and drums have "seated" and at 3,000 mile inter-vals, or as use and performance requires. The adjustment procedures arebeyond the scope of this manual, please see the axle owners/servicemanual for specific instructions.

The trailer brakes should be inspected and serviced at yearly intervalsor more often as use and performance requires. Magnets and shoesmust be changed when they become worn or scored thereby prevent-ing adequate vehicle braking. Again, see the axle owner's/service manualfor specific procedures.

FUEL TANK: Fill the fuel tank at the beginning of the work shift leav-ing a gap of at the top of the tank for expansion of fuel. A full fuel tankwill reduce the possibility of condensation forming in the tank andmoisture entering the fuel lines. Check the fuel lines daily for cracks,holes or tightness.

6.

7.

DO NOT tow the leaf vacuum with damaged or non-operating brakes.Check the brakes daily for proper operation.

Maintenance Section



BATTERY: ODB's units are supplied with "maintenance free" batteriesso there is no need to check fluid levels but the battery terminals should bechecked daily for corrosion. Remove any corrosion with a wire brush andcoat the terminals with light grease or petroleum jelly to reduce the possi-bility of corrosion. Also check the battery cable for wear all cable connec-tions and battery tie downs to be certain that they are not loose.

DRIVE BELT (if equipped): The main drive belt should be checkeddaily for cracks and for proper tension. If the belt shows any sign of

cracking it should be replaced immediately. The proper tension of thebelt should be approximately 1/2" deflection when applying a 8 poundpull.

FASTENERS: Fasteners should be checked weekly for the first 30days and monthly thereafter. They must be in place at all times andproperly torqued. For general torque values see the torque chart at theend of this section.

INSTRUMENT PANEL AND CIRCUIT BOARD: The instrument paneland circuit board should be cleaned with compressed air daily. Alsothe circuit board connectors should be wiped clean and have nonconduc-tive grease applied weekly to help maintain solid connections.

BOOM HYDRAULIC PUMP: Check the fluid level daily. If fluid needsto be added, automatic transmission fluid (ATF) is recommended.Clean debris and oil off the solenoid and pump daily. A build up ofdebris can cause premature failure to the pump. Check and tighten allhydraulic fittings making sure there are no leaks.

8.

9.

10.

11.

12.

ALWAYS wear eye and hand protection when working with the bat-tery.

Remove the negative battery cable before opening the belt guard.

Maintenance Section


4.5 TORQUE VALUES

RECOMMENDED TORQUE IN FOOT POUNDS

TYPE

SAE GRADE

HEX HEAD CAP SCREWS

5 8

SIZE

1/4"

5/16"

3/8"

7/16"

1/2"

9/16"

5/8"

3/4"

7/8"

1"

9

18

33

52

80

115

160

280

450

675

9

18

33

52

80

115

160

280

450

675

HEAD MARK

DO NOT use these values if a different torque value or tightening procedure isgiven for a specific application. Torque values listed are for general use only.Check tightness of fasteners periodically.

Make sure fastener threads are clean and that you properly start thread engage-ment. This will prevent them from failing when tightening.

4.6 QUICK REFERENCE MAINTENANCE CHART:

Only properly trained personnel should perform maintenance orrepair on this equipment. Consult ODB before performing anymaintenance procedures that is not specificially covered in thismanual. Improper maintenance or repair may void any and all war-ranties on this equipment.

Improper maintenance or repair CAN result in equipment damageand/or personal injuries.

BEFORE CONTINUING, please read and understand the Safety, Pre-operating and Operating sections of this manual before doing anyprodcedures in this section.

ITEM

Fuel RequirementFuel CapacityLow / High Idle SpeedEngine Oil: Grade Viscocity

CapacityCoolant: Type Mixture Freezing Point AmountHoist Hydraulic Tank Type

Amount

Diesel fuel specified to EN 590 or ASTM D97530 gallons750 rpm / 2,600 rpm

API service classicfication; CG-4, CF-4SAE15W-40 / SAE10W-40, or SAE 5W-30 (see EOM manual for de-tails)9 US qt

Permanent type of antifreeze; green in color (see EOM manual)Water 50%; Antifreeze 50%; (1:1)-35 degrees C (-31 degrees F)2.5 US gallons

High Viscocity, Premium Hydraulic Fluid; Shell Tellus #68 recom-mended. (ISO 68 viscosity grade)8 US gallons

NOTE: THIS CHART IS FOR REFERENCE ONLY, CONSULT THE ENGINE’S OWNERSMANUAL FOR SPECIFIC DETAILS. FOR JOHN DEERE 4045D ENGINES ONLY.

Maintenance Section


THETHETHETHETHE

SERVICE SECTIONService and TroubleshootingWiring Diagrams

SE

RV

ICE

SE

CT

ION

800-446-9823

ODB COMPODB COMPODB COMPODB COMPODB COMPANYANYANYANYANY5118 Glen Alden DriveRichmond, VA 23231

THETHETHETHETHE

SERVICE AND TROUBLESHOOTING*Service and Repair*Lubrication and Maintenance*Engine Electrical Troubleshooting*Auto PTO Adjustment Guide*Hydraulic Boom Troubleshooting*Impeller Installation

SE

RV

ICE

AN

D T

RO

UB

LE S

HO

OT

ING

800-446-9823


LUBRICATION:We recommend that you check the fluid levels and lubricate your machine daily. If your create a schedule of daily mainte-nance you can avoid a lot of costly down time later in the machine's life.

Start by checking the engine fluid levels. It may be wise to consult your engine owner's manual for other recommendationsconcerning regular maintenance and specific intervals.

Next lubricate the power take off as recommended in the PTO owner's manual. Stein PTO anti-friction bearings should belubricated every 20 hours of operation with a short fiber, high grade, high temperature lithium #2 lubricant having anoperating temperature of 200 degrees F. Three to five pumps with a hand operated grease gun is sufficient. DO NOT MIXSODIUM OR CALCIUM BASE GREASE WITH LITHIUM GREASE. Levers and linkage should be lubricated withengine oil every 50 hours.

The impeller shaft bearings should be lubricated every 8 to 10 hours of operation. We have experimented with variouslubricants and have found the ALMAGARD 3751 lubricant offered by Lubrication Engineers to be a superior product. Youcan obtain this from us or you can contact Lubrication Engineers for a dealer in your area. More information on them islocated in the back of this manual. Other suitable lubricants include Amoco Rycon No.2 and Mobil's Mobilgrease 532.DO NOT OVERLUBRICATE the bearings. Approximately 2 strokes with the average automotive grease gun is sufficienteach time the bearing is lubricated.

AIR FILTER:Air filter service requirements will vary with the conditions under which your machine operates most often. In dustyweather the filter will need to be checked more often than in damp rainy weather. Air filters should be serviced byREPLACEMENT ONLY.

Two stage elements may need the primary element cleaned as often as twice daily, where the secondary element will onlyneed to be checked daily. Filters that become too dirty can cause poor fuel economy and a considerable loss of power.

BLOWER HOUSING:Daily cleaning of the blower housing through the clean out door is recommended to remove any small heavy objects thatmay become trapped in the bottom of the housing. BEFORE opening the inspection door disconnect a battery cable. Alimit safety switch is located on the clean out door but we recommend disconnecting a battery cable before opening thedoor. After cleaning the housing, take time to visually inspect the impeller and blower housing liners for excessive wear orcracking. This only takes a moment but could save extensive down time later.

At the end of every week we recommend that you remove the blower housing face and carefully inspect the impeller andblower housing liners to insure that there is no damage. Operating a unit with a damaged impeller, liner, or blower housingcan cause tremendous damage to the machine and may cause severe injury.

TRAILER:The trailer should only require yearly maintenance such as wheel bearing lubrication and lubrication of the parking jack.The wheel bolts should be checked for tightness EVERY time the leaf collector is used. They should be torqued to 95 ft.lbs.

The lights on the trailer should be checked daily by the driver to insure their proper operation.

SERVICE AND REPAIR SECTION

Periodic cleaning of the battery box and the hydraulic power pack is recommended to help insure reliable operation of thepump and to increase battery life. More information on the hydraulic unit is located in the back of the manual.

The parking jack that is supplied with the leaf vacuum is adequate for support of the unit. Periodic lubcrication of the jackis needed.

PTO:Some power take offs do not require adjustment. These units use a clutch similar to a car or light truck. Others use an overcenter engagement that requires more frequent adjustment. To determine the requirements of your particular unit wesuggest that you consult the manual for your PTO that was supplied with your machine.

BELT ADJUSTMENTS (For Belt Drive Units Only):The type of V belt arrangement supplied with the leaf vacuum is called a power band. Its one piece construction makes itstronger than multiple belts but its service requirements are very similar. Periodically check the band for cracks or signs ofextreme wear. If the band should become loose, it can easily be adjusted using the following method:

1) Turn the engine off and remove a battery cable2) Loosen the 4 bolts that fasten the engine to the adjustable motor mounts.3) Turn the adjusting bolt closest to the band clockwise until the band becomes tight.4) Using a straight edge to check the alignment across the face of the pulleys, turn the other adjusting bolt clockwise until the pulleys are back in line.5) You will notice that as you tighten the second adjuster the band becomes loose again. Repeat steps 3

and 4 until the band has about 1/4" of movement either way in the center of the pulley. It is important to keep the pulleys in line. If they are not, band life will be considerably shortened and vibration may occur.

6) When the band is properly adjusted, tighten the engine mounting bolts and replace all guards.

Hydraulic Hose Boom:Check the fluid level in the hydraulic pump resouvouir every day. If fluid needs to be added be sure to use Dextron IIhydraulic fluid. If the boom travels too fast or too slow adjust the fluid by using the brass fluid control valve located nearthe pump. Be sure to keep the pump clean of debris and check the wiring contacts regularly.

SERVICE AND REPAIR SECTIONPAGE 2

Engine Electrical Troubleshooting Guide

Z X

Make sure the PTO is disengaged.Take a look at the limit switch located at the inspectiondoor of the blower housing. Check to be sure that theinspection door closes completely and that the doorpresses in the limit switch. The limit switch is extremelysensitive and only needs to open 1/64” to shut the engineoff.If the inspection door closes properly and presses in thelimit switch properly, then disconnect the two wires fromthe back of the limit switch.Start the engine using the normal procedure then releasethe shut off button. If the engines continues to run thenthe problem lies in the limit switch or the limit switchwiring. If the engine still cuts off then the limit switch isnot the cause, go to Testing the shut off switch.TO TEST THE LIMIT SWITCH:

Murphy Switch

ENGINE RUNS ONLY WHEN OVERRIDEBUTTON IS DEPRESSED

1.2.

3.

4.

5.

6.7.

8.

9.

TypicalWiringDiagram

Fig. 3

Fig. 2

A

B

With an ohm meter check the resistance of the terminals A & B (Fig. 1) while the button is not depressed.There should be no resistance or continuity. With the button depressed there should be full continuity orinfinite resistance, if not the switch is bad and should be replaced.TESTING THE SHUT OFF (MURPHY) SWITCH:Pull out the ignition switch to the first position.Put a test light to terminal B (Fig. 3) to test for current. If there is no current at B, power is not getting tothe shut off switch. Then the problem is not the shut off switch.If there is current at terminal B, put a test light on the fuse at location Z (Fig. 3) above. If there is no currentthere the fuse is blown. Replace fuse.If there is current at B and Z, push the override button (letter X above, Fig. 3) in on the shut off switch.While the button is depressed place the test light on terminal C (Fig. 3). If there is current at terminal C thenthe shut off switch is functioning properly and the problem lies elsewhere. If there is no current at terminal Cthen the shut off switch is defective and needs to be replaced.Next locate the fuel solenoid valve located on the fuel injector pump (Letter C, Fig. 2). It has an orange wirerunning to it. Pull the ignition switch to the first position. Put a test light on the terminal of the fuel solenoidwhere the wire is attached. Test light should light up showing current, if not shut off switch is bad. Replace.If engine still cuts off after shut off button is released then test the water temperature switch (located on theengine block, Letter D, fig. 2) by removing the brown wire attached to the temperature switch. Start theengine using the normal procedure then release the shut off button. If the engine continues to run then thewater temperature switch is defective. Replace the switch. If the engine shuts off, do the same test on the oilpressure switch. If the engine continues to shut off after this test call ODB for additional service procedures.

C

D

LimitSwitchFig. 1

A

C

B

D

Auto PTO Linkage Adjustment

Adjusting the Auto PTO:Make sure the engine is OFF and remove the negative battery cable to ensure the unit can not accidently be started.Put the PTO in gear so that the PTO handle is at 90 degrees or pointing straight up.Locate the throwout arm which protrudes from the clutch housing (Fig. C).Remove the spring that is attached to the throwout arm and sheet metal.Grab the end of the throwout arm to check for movement or “play”. When properly adjusted the arm should move3/4” to 1” when in gear.If the arm does not move in this range, locate the PTO linkage (Fig. A), then turn the adjuster nut (Fig. B) clock-wise to increase tension, counter clockwise to decrease tension.If there is no adjustment left then the clutch disk most likely needs to be checked/replaced.After adjustment reapply the return spring and negative battery cable.

Units with Clutch Assist Cylinder:Check for movement in the throw out arm as described above.If there is not sufficient “play” in the throwout arm check the setting of the clutch assist cylinder. The cylinder maybe impairing the movement of the throwout arm if not properly adjusted.Adjust the cylinder by turning the adjusting nut (Fig. D) counter clockwise to around setting 7.Once the clutch assist cylinder is properly adjusted, adjust the PTO as described in the first section.

1.

2.3.4.

5.

6.7.

1.2.

3.4.

Hydraulic Boom Trouble Shooting Guideand Wiring Diagram

Boom goes down but not up

While depressing the upbutton is the White wire hot?

Solenoid defective,replace

Yes

Up/Down Switch hasshorts or is defective.

No

Boom goes up but not down

Press the down button, is therecurrent on the green wire?

Check black wire for looseconnections or short.

Check wire connections,electric valve is defective,replace.

Yes No

Black wire has badconnection orswitch is bad,replace switch

No

Is there current onthe black wirelocated at the downbutton

Boom doesn't go up or down

Is there current on Red wireat the solenoid?

Is there current on Blackwire(solenoid to up/downswitch)?

Check cable connection,replace solenoid.

Battery is low or wirehas loose connection

Up/down switch isdefective, replace

No

No

Yes

Yes

Boom moves slow in both directions

Check fluid level in reservoir,fill if necessary

Inspect pump motorreplace if necessary

Check all electricalfittings for loose connec-tions

Checks for leaks at allhoses and fittings

Turn fluid control valvecounter-clockwise to open

Yes

Black(4 ga.)

Up/Down Switch

UPDown

Black

BlueGreen

Red

White

Purple(white bef. 2000)

Valve(down)

Solenoid (up)Red (to Battery)M259 PUMP

Green Wire - controls down modeWhite Wire - controls up modePurple (to housing) - groundBlue Wire (up switch to white wire) - up modeBlack Wire (to push button) - hot wireBlack Wire (solenoid to motor) - hot wireWhite Wire (solenoid to housing) -groundRed Wire (solenoid to battery) - hot wireRed Wire (electric valve to green wire) - down mode

Wiring Descriptions

IMPELLER INSTALLATION AND REMOVAL

REMOVAL

1. The blower housing face must be removed to gain access to theimpeller. Use an overhead crane or forklift to support the facewhile removing.2. Once the face has been removed, remove the shaft protector(Fig. 1 or 2).3. Saturate the shaft and bushing using a penetrating lubricant tohelp loosen the bushing. Clean any grease or debris from thebushing and shaft.4. Remove the 3 bolts attaching the bushing to the impeller.(Fig. 3)Being careful not to break the bolts. If a set screw is on the lip ofthe bushing, loosen it using an allen wrench.(Fig. 4)5. Using two of the bolts that were just removed screw those boltsinto the threaded holes on the bushing. Drive the two bolts intothe bushing.(Fig. 5) This will separate the bushing from the impel-ler. Alternate from one bolt to the other driving only about a 1/4”at a time to keep the bushing coming out straight. It is imperativeto keep the bushing straight to remove it.

Fig. 3

Fig. 4

Fig. 5

6. If the bushing does not come off using the two bolts, drill andtap several additional 3/8-16 holes around the bushing. UsingGrade 8, 3/8-16 - 2 inch bolts, alternately drive the bolts 1/4” at atime to remove the bushing. KEEP THE BUSHING STRAIGHTwhile removing.

IMPORTANT: Be sure to drive the bushing out evenly orit will get in a bind making removal much harder.

7. Once the bushing has been removed use an overhead crane orother suitable device to help lift the impeller out of the blowerhousing.8. At this point it would be a good idea to inspect the blowerhousing liners and blower housing for any damage or wear. Anydamage or wear to the liners should be fixed by replacing the linersimmediately.

IMPORTANT: If additional holes were drilled in thebushing, it can not be reused. It must be be replaced.

CAUTION: Before removing the blower housing faceremove the negative battery cable to ensure unit can notbe started.

!

Fig. 1

Fig. 2

BeltDrive

DirectDrive

IMPELLER INSTALLATION AND REMOVAL--Cont.

6. Tap the bushing onto the shaft aligning the keyways.7. BELT DRIVE UNITS: Align the bushing and key to be flushwith the end of the shaft (Fig 1). DIRECT DRIVE UNITS: The bushing and key should protrudefrom the shaft about 1/2 inch (Fig. 2).8. Put the 3 bolts into the non-threaded holes and drive them intothe impeller holes evenly. Alternate between the three bolts as youdrive the bolts in. Torque to 40 to 50 lbs/ft. There should be a gapof 3/8” to 1/2” between the bushing and the impeller.

1. Clean the shaft of any debris and remove any rust using a 120grit emory cloth.2. Put a generous coat of anti-sieze compound completely aroundthe shaft. This will aid in removing the bushing and impeller thenext time.

INSTALLATION

CAUTION: Before removing the blower housing faceremove the negative battery cable to ensure unit can notbe started.

!

3. Using an overhead crane or other suitable lifting device lift theimpeller on to the shaft. Turn the impeller to align the keyways ofthe shaft with the keyway in the impeller.4. Insert key into the keyway. A light sanding of the keyway maybe needed, as well as a few light blows with a rubber mallet.5. Apply a generous coat of anti-sieze compound to the outside ofthe bushing being sure to cover any area that will come in contactwith the impeller.

IMPORTANT: Use an anti-sieze compound on the shaftand bushing to keep the bushing from “welding” itselfto the shaft. This makes removal much easier.

9. If the bushing has a set screw on it, tighten the screw snug withan allen wrench (Fig. 3). This will help keep the key in place.10. Install the shaft protector on to the shaft (Fig. 4 or 5).

IMPORTANT: Slowly spin the impeller by hand makingsure that the back of the impeller is not hitting any ofthe bolt heads located at the back of the blower housing.

Fig. 1

Fig. 2

Fig. 3

BeltDrive

DirectDrive

Fig. 4

Fig. 5

WIRING DIAGRAMS

*Engine Wiring Diagram- overall diagram*Engine Main Harness Diagram - Enlarged*Auxillary Engine Harness - Enlarged*Engine Wiring Harness Descriptions*Engine Rocker Switch Wiring Diagrams

*Engine Wiring Diagram- overall diagram*Engine Main Harness Diagram - Enlarged*Auxillary Engine Harness - Enlarged*Engine Wiring Harness Descriptions*Engine Rocker Switch Wiring Diagrams

*Trailer Plug Wiring Diagram*Trailer Wiring Diagram*Boom Pump Wiring Diagram*Remote Throttle / Clutch Diagram (optional)

WIR

ING

DIA

GR

AM

S

800-446-9823


JOHN DEERE ENGINES

CATERPILLAR ENGINES

EITHER ENGINE

THETHETHETHETHE

JOHN DEERE WIRING DIAGRAMS*Engine Wiring Diagram- overall diagram*Engine Main Harness Diagram - Enlarged*Auxillary Engine Harness - Enlarged*Engine Wiring Harness Descriptions*Engine Rocker Switch Wiring Diagrams

WIR

ING

DIA

GR

AM

S

800-446-9823


Engine Main Harness

1Please see enlarged dia-grams on the following pages:

2

Engine Wiring Harness Diagram Aux Engine Harness

June 2005 and after

Note:The number in parentheses is the pin number the wire goes to. If there are two numbers the first number is the pin for the main harness, while the second number is the pin number of the smaller harness

Engine Main Harness - Enlarged

Engine Main Harness

June 2005 and after

Auxillary Engine Harness - EnlargedJune 2005 and after

Aux Engine Harness

Note:Not all wires will be installed in the small harnesses. If the unit wasn’t ordered with the factory installed option then the wiring to that option may not be included in the harness

"+" from Solenoid (battery)Starter SolenoidFuel Shutoff Solenoid"-" from Solenoid (battery)Alternator Engergize "+"Oil SenderTach Signal form AlternatorEmergency Stop Button (650 only); goes to Limit Switch Plug pin# 5Inspection Door on Blower Housing; goes to Limit Switch Plug pin# 3Fuel Sender; goes to Limit Switch Plug pin# 1Water Temperature Sender on Engine BlockWater Temperature Switch on Engine BlockOil Pressure Switch on Engine Block

RedRed w/ Blue StripeOrangeBlackPurpleWhite w/ Red StripeWhiteTan w/ Black StripeTanPinkBlueBlue w/ Black StripeRed w/ Black Stripe

Pin# Color Description

Engine Wiring Harness

123456789

10111213

Wire Diagram Descriptions June 2005 and afterENGINE MAIN HARNESS

"+" from Solenoid (battery)Aux "+" from Ignition; goes to Aux Plug Harness pin #5Aux "+" from Ignition; goes to Remote Clutch Harness pin #1Engine Heater Switch "+"; goes to Aux Plug Harness pin#7(Cat engine only)Engine Heater Aux; goes to Aux Plug Harness pin#8 (Cat engine only)Clutch Engage; goes to Remote Clutch Harness pin# 3

Clutch Disengage; goes to Remote Clutch Harness pin#4Throttle Fast; goes to Remote Clutch Harness pin# 7

Throttle Slow; goes to Remote Clutch Harnss pin# 8Strobe Light "+"; goes to Strobe Light Harness pin# 1Strobe Light Aux; goes to Strobe Light Harness pin# 3Aux "+" from Ignition; goes to Aux Plug Harness pin# 1"-" from Solenoid (Battery)Aux "+" from Igntion; goes to Aux Plug Harness pin# 3

Red 10 gaugeYellowYellowYellow w/ Orange StripeOrange w/ Yellow StripeYellow w/ Green Stripe[EMPTY]Green w/ Yellow StripeYellow w/ Blue Stripe[EMPTY]Blue w/ Yellow StripeYellow w/ Purple StripePurple w/ Yellow StripeYellowBlack 10 gaugeYellow

123456789

10111213141516

AUXILLARY ENGINE HARNESS

Strobe Light "+"; came from Aux Engine Harness pin# 12Strobe Light "-"; came from ground on SolenoidStrobe Switch Aux "+"; came from Aux Engine Harness pin#13Strobe Switch Aux "-"; came from ground on Solenoid

Fuel Sender "+"; came from Engine Main Harness pin# 10Fuel Sender "-"; came from ground on SolenoidInspection Door "+"; came from Engine Main Harness pin# 9Inspection Door "-"; came from ground on SolenoidEmergency Stop Button "NO"; came from Engine Main Harness# 8Emergency Stop Button "COM"; came from ground on Solenoid

"+" from Ignition; came from Aux Engine Harness pin# 3"-" from Ignition; came from ground on SolenoidClutch Engage; came from Aux Engine Harness pin# 6Clutch Disengage; came from Aux Engine Harness pin# 4

Throttle Fast; came from Aux Engine Harness pin# 9Throttle Slow; came from Aux Engine Harness pin# 11

"+" from Ignition; came from Aux Engine Harness pin# 14"-" from Ignition; came from ground on Solenoid"+" from Ignition; came from Aux Engine Harness pin# 16"-" from Ignition; came from ground on Solenoid"+" from ignition; came form Aux Engine Harness pin# 2"-" from ignition; came from ground on solenoid

Rocker Switch; came from Aux Engine Harness pin# 5

Yellow w/ Purple StripeBlackPurple w/ Yellow StripeBlack

PinkBlackTanBlackTan w/ Black StripeBlack[EMPTY]

YellowBlackYellow w/ Green StripeGreen w/ Yellow Stripe[EMPTY][EMPTY]Yellow w/ Blue StripeBlue w/ Yellow Stripe[EMPTY]

YellowBlackYellowBlackYellowBlack[EMPTY]Orange w/ Yellow Stripe[EMPTY]

1234

1234567

123456789

123456789

STROBE LIGHT HARNESS

FUEL & LIMIT SWITCH HARNESS

REMOTE THROTTLE AND CLUTCH HARNESS

AUX PLUG IN HARNESS

Engine Rocker Switch Wiring DiagramsJune 2005 and after

Strobe Light Rocker Switch

Yellow

Yellow with Purple Stripe

Purple with Yellow Stripe

Black

Yellow

Yellow with Purple Stripe

PlugsintoCircuitBoard

Yel

low

with

Pur

ple

Str

ipe

Yel

low

with

Pur

ple

Str

ipe

Bla

ck

Bla

ck

Yel

low

with

Pur

ple

Str

ipe

Yel

low

with

Pur

ple

Str

ipe

Yel

low

Pur

ple

with

Yel

low

Str

ipe

Pur

ple

with

Yel

low

Str

ipe

12345678910

Purple w/ Yellow StripeYellowYellow w/Purple StripeYellow w/Purple StripeYellow

BlackPurple w/Yellow StripeBlackYellow w/ Purple Stripe

“+” Aux from Switch“+” from Circuit Board“+” from Strobe LightLooped from #3Looped from #2

“-” from Circuit BoardLooped from #1Looped from #7Looped from #4


Remote Throttle and Remote Clutch Rocker Switch12345678910

Yellow w/ Blue StripeYellowYellow w/ Green Stripe

Black

BlackYellowBlackYellow

Throttle Fast / Clutch Engage“+” from Circuit BoardThrottle Slow / Clutch Disengage

“-” from Circuit Board

Looped from #9Looped from #10Looped from #5Looped from $2


Caterpiilar Engine Heater Rocker Switch12345678910

Orange w/ Yellow StripeYellowYellow w/Orange Stripe

Yellow

BlackOrange w/Yellow StripeBlackYellow w/Orange Stripe

“+” Aux from Switch“+” from Circuit Board“+” to Engine Heater

Looped from #2

“-” from Circuit BoardLooped from #1Looped from #7Looped from #3


Black

Yellow with Blue Stripe

Yellow with Green Stripe

Yellow

Yel

low

Bla

ck

Bla

ck

Yel

low

with

Blu

e S

trip

e

Bla

ck

Yel

low

Yel

low

with

Blu

e S

trip

e

Yellow with Blue Stripe

Yellow with Green StripeYel

low

with

Gre

en S

trip

e

Yellow

Yel

low Plugs

intoCircuitBoard

This plug is used for the Remote Throttle and theRemote Clutch Rocker Switches.

PlugsintoCircuitBoard

Yel

low

Yellow

Yel

low

with

Ora

nge

Str

ipe

Yellow with Orange Stripe

Orange with Yellow Stripe

Ora

nge

with

Yel

low

Str

ipe

Ora

nge

with

Yel

low

Str

ipe

Bla

ck

Bla

ckYel

low

Yellow

Orange w/ Yellow Stripe

Yellow with Orange Stripe

Black

Ora

nge

with

Yel

low

Str

ipe

Yel

low

with

Ora

nge

Str

ipe Yellow

CATERPILLAR WIRING DIAGRAMS*Engine Wiring Diagram- overall diagram*Engine Main Harness Diagram - Enlarged*Auxillary Engine Harness - Enlarged*Engine Wiring Harness Descriptions*Engine Rocker Switch Wiring Diagrams

WIR

ING

DIA

GR

AM

S

800-446-9823


Please see enlarged diagrams on the following pages:

Engine Wiring Harness DiagramCATERPILLAR - June 2005

Note:The number in parentheses is the pin number the wire goes to. If there are two numbers the first number is the pin for the main harness, while the second number is the pin number of the smaller harness

Engine Main Harness

Aux Engine Harness

Engine Main Harness - Caterpillar - EnlargedJune 2005 and after

Auxillary Engine Harness - Caterpillar - EnlargedJune 2005 and after

Note:Not all wires will be installed in the small harnesses. If the unit wasn’t ordered with the factory installed option then the wiring to that option may not be included in the harness

"+" from Solenoid (battery)Starter SolenoidFuel Shutoff Solenoid"-" from Solenoid (battery)Alternator Engergize "+"Oil SenderTach Signal form AlternatorEmergency Stop Button (650 only); goes to Limit Switch Plug pin# 5Inspection Door on Blower Housing; goes to Limit Switch Plug pin# 3Fuel Sender; goes to Limit Switch Plug pin# 1Water Temperature Sender on Engine BlockWater Temperature Switch on Engine BlockOil Pressure Switch on Engine Block

RedRed w/ Blue StripeOrangeBlackPurpleWhite w/ Red StripeWhiteTan w/ Black StripeTanPinkBlueBlue w/ Black StripeRed w/ Black Stripe


Engine Wiring Harness - Caterpillar

123456789

10111213

Wire Diagram Descriptions June 2005 and afterENGINE MAIN HARNESS

"+" from Solenoid (battery)Aux "+" from Ignition; goes to Remote Clutch Harness pin #1Aux "+" from Ignition; goes to Electric Lift Pump Plug and jumps to Cat Water Temp SwitchEngine Heater Switch "+"; goes to Cold Start Relay(Cat engine only)Engine Heater Aux; goes to Aux Plug Harness pin#8 (Cat engine only)Clutch Engage; goes to Remote Clutch Harness pin# 3

Clutch Disengage; goes to Remote Clutch Harness pin#4Throttle Fast; goes to Remote Clutch Harness pin# 7

Throttle Slow; goes to Remote Clutch Harnss pin# 8Strobe Light "+"; goes to Strobe Light Harness pin# 1Strobe Light Aux; goes to Strobe Light Harness pin# 3Aux "+" from Ignition; goes to Aux Plug Harness pin# 1"-" from Solenoid (Battery)Aux "+" from Igntion; goes to Aux Plug Harness pin# 3

Red 10 gaugeYellowYellowYellow w/ Orange StripeOrange w/ Yellow StripeYellow w/ Green Stripe[EMPTY]Green w/ Yellow StripeYellow w/ Blue Stripe[EMPTY]Blue w/ Yellow StripeYellow w/ Purple StripePurple w/ Yellow StripeYellowBlack 10 gaugeYellow

123456789

10111213141516

AUXILLARY ENGINE HARNESS

Strobe Light "+"; came from Aux Engine Harness pin# 12Strobe Light "-"; came from ground on SolenoidStrobe Switch Aux "+"; came from Aux Engine Harness pin#13Strobe Switch Aux "-"; came from ground on Solenoid

Fuel Sender "+"; came from Engine Main Harness pin# 10Fuel Sender "-"; came from ground on SolenoidInspection Door "+"; came from Engine Main Harness pin# 9Inspection Door "-"; came from ground on SolenoidEmergency Stop Button "NO"; came from Engine Main Harness# 8Emergency Stop Button "COM"; came from ground on Solenoid

"+" from Ignition; came from Aux Engine Harness pin# 2"-" from Ignition; came from ground on SolenoidClutch Engage; came from Aux Engine Harness pin# 6Clutch Disengage; came from Aux Engine Harness pin# 4

Throttle Fast; came from Aux Engine Harness pin# 9Throttle Slow; came from Aux Engine Harness pin# 11

"+" from Ignition; came from Aux Engine Harness pin# 14"-" from Ignition; came from ground on Solenoid"+" from Ignition; came from Aux Engine Harness pin# 16"-" from Ignition; came from ground on Solenoid

Rocker Switch; came from Aux Engine Harness pin# 5

Yellow w/ Purple StripeBlackPurple w/ Yellow StripeBlack

PinkBlackTanBlackTan w/ Black StripeBlack[EMPTY]

YellowBlackYellow w/ Green StripeGreen w/ Yellow Stripe[EMPTY][EMPTY]Yellow w/ Blue StripeBlue w/ Yellow Stripe[EMPTY]

YellowBlackYellowBlack[EMPTY[EMPTY][EMPTY]Orange w/ Yellow Stripe[EMPTY]

1234

1234567

123456789

123456789

STROBE LIGHT HARNESS

FUEL & LIMIT SWITCH HARNESS

REMOTE THROTTLE AND CLUTCH HARNESS

AUX PLUG IN HARNESS

Main Circuit BoardJune 2005 and after

A

OilS +

The circuit board has traces on 2 layers - the top and bottom.

TOP LAYER

BOTTOM LAYER(looking from the back

Oil S+Gauge light

Gauge light

10 a

mp

circ

. bre

aker

TempS + Gauge light

Gauge light Tach

+(-)Sig

VoltS + Gauge light

Strobe Light

+(+) s s (-) 1234

Main Plug Wire ID’s1 + from Battery (Red)

2 Starter + (Red/Blue)

3 Fuel Sol./Col + (Orange)

4 Ground (Black)

5 Alt Energize + (Purple)

6 Oil Signal (White/Red)

7 Tach Signal (White)

8 E Stop Sig. (Tan/Black)

9 Insp. Door Sig. (Tan)

10 Fuel Level Sig. (Pink)

11 Temp Sig. (Blue)

12 Temp Shtdwn Sig (Blue/Blk)

13 Oil Shutdown Sig. (Red/Blk)

56789

10111213

Rem. Clutch

Eng. Heat

(+) s s (-)

(+) s s (-)

(+) s s (-)

10 amp Circ. Brk

10 amp Circ. Brk

10 amp Circ. Brk

10 amp Circ. Brk

+

+

+

30 a

mp

circ

. bre

aker

FuelS Gauge light

Yellow/Red

Yellow/Red

Yellow/RedYellow/Red

(-) (-) (-)

Rem. Throttle

ShutdownIndicator Lights

Oil

Temp

Trp Door

E Stop

(+) (+) unfused Battery

(+) (-) Red Black

+ from ignition Yellow

14 15

16 17

18 19

20 21

Relay

Aux Plug Wire ID’s

14 Eng Heat (+) (Yellow/Orange)

15 Eng. Heat Aux (Orange/Yellow)

16 Clutch Engage (Yellow/Green)

17 Clutch Disengage (Green/Yel)

18 Throttle Fast (Yellow/Blue)

19 Throttle Slow (Blue/Yellow)

20 Strobe Light + (Yellow/Purple)

21 Aux Light + (Purple/Yellow)

Temp+ S

Fuel Volt S++ SGauge light

Gauge light

Tach+ Sig

(-)

ShutdownIndicator Lights

Oil

Temp

Trp Door

E Stop

Strobe Light

Rem. Clutch

Eng. Heat

Rem. Throttle

(+) (-) s s

BSC

BSC

10 amp Circ. Brk

10 amp Circ. Brk

10 amp Circ. Brk

10 amp Circ. Brk

(+) (-) s s

10 a

mp

circ

. bre

aker

(-) (-) (-) Battery (+) (-) (+) (+)

unfused

30 a

mp

circ

. bre

aker

(+) (-) s s

(+) (-) s s 1234

56789

10111213

15

17

19

21

14

16

18

20

Aux Wire

Relay

+ from ignition Yellow

diode

diode

diode

diode

Igni

tion

Switc

h

ISBM

urph

y Sw

itch

Mur

phy

Switc

h

A

Igni

tion

Switc

h

ISB

Main Wire

Aux Wire

Main Wire

Main Circuit Board Plug DiagramsJune 2005 and after

1 Red + from battery

2 Red / Blue stripe - starter +

3 Orange - Fuel Sol./Col +

4 Black - Ground

5 Purple Alt Energize +

6 White / Red stripe Oil Signal

7 White - Tach Signal

8 Tan / Black stripeE Stop Sig.

9 Tan - Insp. Door Signal

10 Pink - Fuel Level Signal

11 Blue - Temp Signal

12 Blue/Black Temp Shtdwn Sig

13 Red/Black Oil Shutdown Sig.

14 Empty

15 Empty

16 Empty

Pin# Description

1 Red + from battery

2 Yellow - Aux Plug harness

3 Yellow - Remote Throttle Har

4 Yellow / Orange stripe-Aux har

5 Orange / Yellow stripe-Aux har

6 Yellow / Green stripe-Clutch Eng

7 Empty

8 Green / Yellow stripe-Clutch Diseng

9 Yellow / Blue stripe-Throttle Fast

10 Empty

11 Blue / Yellow stripe-Throttle Slow

12 Yellow / Blue stripe-Strobe +

13 Purple / Yellow stripe-Strobe Sw+

14 Yellow - Aux Harness

15 Black - battery

16 Yellow - Aux Harness

Pin# Description

Main Harness Plug

Aux. Harness Plug

Remote Throttle / Clutch Wiring HarnessJune 2005 and after

THETHETHETHETHE

PARTS BREAKDOWNSSECTION

Engine GroupClutch GroupBlower Housing GroupTrailer GroupHose Boom Group

PAR

TS

BR

EA

KD

OW

N S

EC

TIO

N

800-446-9823


THETHETHETHETHE

ENGINE GROUP*Instrument Panel*Strobe Light Group*Air Cleaner*Engine Sheet Metal*Engine Mount*Engine Exhaust*Radiator Assembly*Engine Sender and Switch Group*Remote Throttle / Clutch Assembly (optional)*Remote Throttle / Clutch Circuit Board Assembly (optional)*Chaffe Eliminator (optional)*Engine Miscellaneous Parts (throttle connector, startersolenoid, door grommet, fuel line bracket)

EN

GIN

E G

RO

UP

800-446-9823


Instrument Panel Complete Instrument Panel Housing, with 2 LatchesLatchLatch HookCircuit BoardTachometer Circuit BoardMurphy Switch Harness PlugIgnition Switch Harness PlugCircuit Board Support Bracket LHCircuit Board Support Bracket RHCircuit Breaker, 10 ampCircuit Breaker, 30 ampRelayMurphy SwitchIgnition Switch Nov 2008 and afterTachometer / Hour Meter

STD.6300STD.6301STD.6308STD.6309STD.2005STD.2006400022400021STD.6303STD.6302100014.1030410.300.332.209.151MO-P8150531.25363524

ITEMNO.


Instrument Panel Group

1.2.3.4.5.6.7.8.9.

10.11.12.13.14.15.

Standard units Nov 2008 and after

2

1

4

6

5

7

10

9

8

1112

13

14

15

16

Temperature GaugeOil Pressure GaugeFuel Gauge (if equipped)Blank Gauge (non-electric fuel gauge)Volt MeterRocker Switch, Safety LightRocker Switch, Remote ThrottleRocker Switch, Remote PTORocker Switch, Cold Start(Cat eng)Switch Harness, Safety LightSwitch Harness, Remote ThrottleSwitch Harness, Remote PTOSwitch Harness, Cold Start (Cat eng)L.E.D. Light AssemblyThrottle Cable

62540625426255159414625554045.0021B4045.0021A4045.00253054.0028STD.2003STD.2004STD.2004STD.2002STD.1502BLCT623.001A

ITEMNO.


16.17.18.

19.20.21.22.23.24.25.26.27.28.29.

17

18

24

25

26

27

28

3

10

19

20

21

22

23

29

Instrument Panel Complete Instrument Panel Housing, with 2 LatchesLatchLatch HookCircuit BoardTachometer Circuit BoardMurphy Switch Harness PlugIgnition Switch Harness PlugCircuit Board Support Bracket LHCircuit Board Support Bracket RHCircuit Breaker, 10 ampCircuit Breaker, 30 ampRelayMurphy SwitchIgnition Switch, thru Oct 2008Tachometer / Hour Meter

STD.6300STD.6301STD.6308STD.6309STD.2005STD.2006400022400021STD.6303STD.6302100014.1030410.300.332.209.151MO-P81505957663524

ITEMNO.


Instrument Panel Group

1.2.3.4.5.6.7.8.9.

10.11.12.13.14.15.

Standard units June 2005 - Oct 2008

2

1

4

6

5

7

10

9

8

1112

13

14

15

16

Temperature GaugeOil Pressure GaugeFuel Gauge (if equipped)Blank Gauge (non-electric fuel gauge)Volt MeterRocker Switch, Safety LightRocker Switch, Remote ThrottleRocker Switch, Remote PTORocker Switch, Cold Start(Cat eng)Switch Harness, Safety LightSwitch Harness, Remote ThrottleSwitch Harness, Remote PTOSwitch Harness, Cold Start (Cat eng)L.E.D. Light AssemblyThrottle Cable

62540625426255159414625554045.0021B4045.0021A4045.00253054.0028STD.2003STD.2004STD.2004STD.2002STD.1502BLCT623.001A

ITEMNO.


16.17.18.

19.20.21.22.23.24.25.26.27.28.29.

17

18

24

25

26

27

28

3

10

19

20

21

22

23

29

Strobe Light Parts Group

L.E.D. Strobe Light with internal flash module, 2004 and afterL.E.D. Light only, through 12/2003GrommetRocker SwitchSwitch Wiring HarnessStrobe Module (makes the light flash), LCT650, through 12/2003Strobe Module with 4 prong connector on LCT60C and LCT600/6000 only, through 12/2003Wiring Harness, rocker switch to light, 2004 and after

STD.221360094Y607004045.0021B4045.0024B9725197251.WH

STD.2214

1.

2.3.4.5.6.

ITEMNO.


John Deere Engines 2002 and after

NOTE: 01/01/04 we changed to a new style strobe light that has an internal flash module, thus a separte flash module is not needed.

2

1

3 54

LCT600/6000 and LCT60C only

6

AIR CLEANER GROUP

Air Cleaner Assembly w/filter Filter Element Clamp Rubber Baffle Dust Cap Wing Nut Vacuator Valve (rubber) Mounting Bands (to sheet metal)Pre-Cleaner Assembly Bowl Cover Bowl

OD-G065012 P18.1052 P002940 P102510 P102805 P101870 P103198 P007191H001251 P020648 P020227

1.2.3.4.5.6.7.8.9.10.11.

John Deere

Ford,(4 cyl. regular)

only used bef. 04/04

JD 4 cyl. Turbo**,JD 6 cyl.

UU-G080023 P18105.4 P003951 P102980 P103113 P101870 N/A P004307H001249 P020648 P020227

*

* Before July 1999, LCT650 with John Deere engines used G080023 (8" diam,)air cleaners andH001249 pre-cleaners.

8 7

Approx. 08/96 and after

6.5" Diam. 8" Diam.

** May 2004 and after all ODB LCT's and SCL's use UU-G080023 8" diameter fiters as standard.

1

2

3

4

56

7

11

16

1314

6

15

15

8

17

6

18

19

28

20

20

20

20

30

30

30

10

29

26

27

9

812

30

30

30

21

22

23

24

Exploded View of #20

24

25

John Deere 4045D July 2001 and afterLCT650 Sheet Metal Group

1.2.3.4.5.6.7.8.9.

10.11.12.13.14.15.16.

650.21014045.0018LCT650.114650.2101LCT650.667ALCT60.624ALCT650.668650.2111650.2114650.2109650.2105650.2116LCT650.134LCT650.135LCT650.108650.2105

17.18.19.20.21.22.23.24.25.26.27.28.29.30.31.

Door Center, RHDoor Rear, RH, inst. panelDoor Guide Rail, topGuide Roller Assembly Roller Roller Carriage Set Collar Bolt Carriage PinDoor StopDoor Stop RubberDoor Guide Rail BottomEnd Plate, LHHingeEmergency Stop Button

650.2113650.2115650.2121650.2123AS 650.2123 650.2124 650.2126 650.2127 650.2125650.2130650.2131650.2122650.2108650.2128800T

PARTNUMBER

DESCRIPTIONITEMNO.

DESCRIPTIONPARTNUMBER

ITEMNO.

Nose ConeRadiator ScreenRad. Screen LatchTop PanelBearing Access DoorLift and Turn LatchRadiator Access DoorDoor Front, RHDoor Center, LHEnd Plate, RHSide Panel, RHDoor Rear, LH stop switchBack Plate, LHBack Plate, RHNose Cone HandleSide Panel, LH

John Deere 4045D, 4045T and 6068D after 08/96Ford BSD444 & 666 Diesel after 09/97

Sheet Metal Group, except LCT650

1.

2.3.4.5.6.7.8.9.

4045.21024045T.21026068.21024045.2102S4045T.2102S6068.2102S4045.2102A4045.2102CLCT60.624A4045.2102B4045.21014045.0018LCT650.1144045.21096068.2109

10.

11.

12.

13.

14.15.

Upper Side Panel, LHUpper Side Panel, LH-turboUpper Side Panel, LH- 6cyl dieselRear Panel, J/D natural and J/D turbo noton SCL's; Ford engines not on SCLRear Panel, SCL's with JD turboRear Panel, Ford SCL'sUpper Side Panel, RH -02/01Upper Side Panel, RH 03/01-Upper Side Panel, RH 6 cyl dieselPanel Door, RHPanel Door, RH 6 cyl. dieselLift and Turn LatchOvercenter Latch

4045.21064045.2106A6068.21064045.2112

4045.2112T4045.2112S4045.21054045.2105A6068.21054045.21086068.2108LCT60.624ALCT609.602

PARTNUMBER

DESCRIPTIONITEMNO.

DESCRIPTIONPARTNUMBER

ITEMNO.

Hood, except SCL800Hood, JD Turbo, exc. SCLHood, 6 cyl. diesel, exc. SCLHood, SCL800 JD naturalHood, SCL800, JD TurboHood, SCL800, JD 6 cyl. dieselRadiator Access DoorRad. Access Door HingeLift And Turn LatchOil Fill Access DoorFront PanelRadiator ScreenRadiator Screen ClampPanel Door, LHPanel Door, LH 6 cyl. diesel

1

23

4

5

4 3

6

7

8

15

9

10

11

12

13

14

John Deere 4045D, 4045T and 6068D after 08/96, Caterpillar 2005 and afterEngine Mount Group

1.

2.

3.

4.

5.6.7.8.9.

4045.21513054.21514045.21523054.21524045.21544045.21566068.21544045.21534045.2153B6068.2153LCT604.603.1LCT604.603.1ALCT604.603.2LCT604.603.B4045.2155

PARTNUMBER

DESCRIPTIONITEMNO.

Engine Mount, FrontEngine Mount, Front, CaterpillarEngine Mount, RearEngine Mount, Rear, CaterpillarSide Rail, LH, except LCT650Side Rail, LH - LCT650 onlySide Rail, LH, J/D 6 cyl. dieselSide Rail, RHSide Rail, RH, LCT650 onlySide Rail, RH, J/D 6 cyl. dieselEngine Adjuster Nut, belt drive units onlyEngine Adjuster Bracket, belt drive units onlyAdjustable Motor Mount, belt drive units onlyEngine Base Adjuster (LCT600/6000 only)Wire Harnesses Bracket, June 2005 and after

3

1

2

3

4

5

6

7

8

8

9

Radiator Side

LCT650 rail

Muffler (Exhaust) AssemblyLCT's only (not SCL's) May 2004 and after

1.2.3.

JD-R123171STD.2702650.2701

PARTNUMBER

DESCRIPTIONITEMNO.

Exhaust Manifold, LCT's with turbo onlyClamp, mufflerMuffler, LCT600 /6000/60C/650

Notes: The above parts are only for John Deere TURBO engines only. May 2004 and after, all ODB unitsuse Turbos as standard. ODB serial numbers 3897, 3900 and after have John Deere Turbo engines.

1

2

3

1

2

3

4

5 6

7

8

9

10

10

1112

13

Radiator Assembly Group

Radiator, 4 cyl.Radiator, turbo and 6 cyl.Front Fan ShroudRear Fan ShroudRadiator FanFan SpacerSpacer Bolts, 4 req.

4045.95004045.95014045.2190B4045.2190AAT35158R128443G8M8X090

1.

2.3.4.5.6.

ITEMNO.


John Deere after August 1996

Upper Radiator HoseRadiator CapLower Radiator HoseRadiator ShimRadiator GrommetRadiator Bolt BracketShoulder Bolt

81331C.89C.022.50104045.96814045.2151E2651.260124045.2151FZSB.500.750

7.8.9.

10.11.12.13.

ITEMNO.


Battery, not shippableJ-Hook Battery Hold Down BarBattery Tray, all but SCL'sBattery Tray, SCLPositive Battery Cable, Battery to Solenoid - SCL (standard)/650/60C - 42" longPositive Battery Cable, Battery to Solenoid - SCL (Belt-Drive)/LCT600/6000 - 84" longNegative Battery Cable, all - 15" longTerminal Cover, Red, allTerminal Cover, Black, allRed Cable to Hydraulic Boom Pump, SCL/600/6000 - 72" longRed Cable to Hydraulic Boom Pump, LCT650 - 60" longRed Cable to Hydraulic Boom Pump, LCT60C - 153" longGround (Black) Cable to Chassis, 600/6000/60C - 24"

STD.2200BHB10JBHCBBTS1BTSCLSCL.42BLCT600.84BLCT60.15BBTC.RBTCLCT600.72SSMET.60SSLCT60C.153SSLCT600.24SS

ITEMNO.


Battery Group

1.2.3.4.5.6.

7.8.9.

10.

11.

Standard units 2001 and after

Remote Clutch / Throttle Circuit Board Assembly October 2005 and after with remote throttle / clutch option

Entire AssemblyBox and CoverBacking PlateSpacer, requires 4Circuit BoardActuator Wiring HarnessInstrument Panel and Nozzle Wiring Harness

STD.3000STD.3000DSTD.3000ASTD.3000BSTD.3000CSTD.3000ESTD.3000F

*1.2.3.4.5.6.

ITEMNO.


Note: This assembly is only used if the unit is equipped with the OPTIONAL remote clutch or remote throttleconfiguration.

Remote Clutch and Remote Throttle Assembly after March 2002- ver. 2

Entire Assembly (see note)Entire Assemby (see note)Mounting BaseMounting Base Thick SpacerMounting Base Thin SpacerWiring HarnessLimit Switch (thru 2005)Clutch Cable- direct driveClutch Cable- belt drive 800Clutch Actuator (top)Cable Adaptor- clutchThrottle Cable-direct driveThrottle Cable-belt drive 800Throttle Actuator (bottom)

STD.6550STD.6550BSTD.6551ASTD.6551A.01STD.6551A.02STD.6566STD.6555STD.6554STD.6554BSTD.6556STD.6559STD.6553STD.6553BSTD.6557

**1.2.3.4.5.6.

7.8.9.

10.

ITEMNO.


Cable Adaptor- throttleCoverThrottle Cable BracketClutch Cable BracketTorque CouplingTorque Coupling SleevePTO Cable AdaptorRoller BearingSpacing Washer

Collar CamLimit SwitchCoverLimit Switch Bracket

STD.6558STD.6552A4045.65654045.6564STD.6563STD.6562STD.6560STD.6561STD.6568

STD.6569800.434STD.6571STD.6570

11.12.13.14.15.16.17.18.19.

20.21.22.23.

ITEMNO.


Parts Below used on SCL8003X Computer Models only

Note: STD.6550 Assembly has item #5 switches installed. These were used up to 2005. STD.6550B Assembly does not have item #5 switches installed and used from 2006 and after. The STD.6550B uses the item #21 switches to activate the indicator lights.

Chaffe Eliminator Assembly, hinged

1.2.3.4.5.6.7.8.9.10.11.12.13.14.

15.

RAS.102RAS.103RAS.104RAS.105RAS.106RAS.107RAS.108RAS.101RAS.109RAS.110RAS.111RAS.112RAS.113LCT609.602LCT650.114RAS.114

PARTNUMBER

DESCRIPTIONITEMNO.

Base FrameBarrell AsssemblySupport FrameShaftMesh ScreenScreen HolderFlange BearingFanStrip BrushBrush HolderAir DeflectorHingeShaft BracketOvercenter Latch, all but LCT650Destaco Latch, not shown, LCT650 onlyAngle Frame, LCT650 only

1

2

3

4

6

7

7

11

10

9

8

5

12

13

14

15

THETHETHETHETHE

CLUTCH GROUP*Clutch Breakdown*Auto PTO Breakdown*Auto PTO Linkage*Clutch Assist Breakdown

CLU

TCH

GR

OU

P

800-446-9823


AutoHD PTO Clutch GroupFebruary 2006 - Present

*Complete PTO and Clutch Assembly 02/06-02/08 *Complete PTO and Clutch Assembly 03/08 - Pilot Bearing, JDClutch DiskPressure Plate, 02/06-02/08Pressure Plate, 03/08 -Throw out Bearing,02/06-02/08Throw out Bearing,03/08 -Clutch CoverBolt, 3/18-16 x 1"Lock Washer, 3/8"Bolt, M10-1.50 x 35MM Lock Washer, M10Decal, Diesel Clutch

OD-48080050OD-48080050.8OFOD-41500217OD-41500237OD-41500209OD-41500060OD-41500003OD-41500248OD-41500172OD-45000054OD-45000063OD-45000226OD-45000046OD-41500216

**1.2.3.3.4.

5.6.7.8.9.

10.

ITEMNO.


Note: *48080050 and 48080050.8OF includes the everything on this page, the AutoHD PTO page and the AutoHD linkage page. This is the complete PTO/Clutch assembly. It does not include the clutch assist assembly.

Complete PTO Assembly (items 1 -11,13)**Complete PTO & Clutch AssemblyBolt, 5/16-18 x 1-1/4" HD modelBearing Retainer CoverPTO Bearing, RearKey, Stepdown--direct drive units onlyKey, belt drive units onlyPTO shaftBolt, 9/16-12 x 1- 3/4"Bolt, 9/16-12 x 3"Lock Washer, 9/16"PTO HousingPTO Collar, 03/08 - presentPTO Collar thru 02/08PTO Bearing, Front

* **1.2.3.4.

5.6.7.8.9.

10.

11.

ITEMNO. DESCRIPTION

OD-41500252OD-48080050.8OFOD-45000212OD-41500205OD-41500206OD-LCT650.601KOD-LCT650.601FOD-41500203OD-45000105OD-45000177OD-45000103OD-41500204OD-41500242OD-41500202OD-41500207

PARTNUMBER

The AutoHD end cap is 6-sided, the older Auto is round. They are not interchangeable! Some units in the time period above used the standard Auto PTO. Please verify.

AutoHD PTO Assembly GroupFebruary 2006 - Present

AutoHD PTO Linkage GroupFebruary 2006 - Present

Fork, 02/06-02/08Fork, 03/08-Clip Spring in ForkReturn SpringLinkage BracketLinkage BracketLinkage RodLinkage RodLinkage Rod EndShaft, LeverShaft Housing, AutoHDGrease ZerkClutch HandleShaft Bushing

415000634150025141500174415009994150009541500241415000654150006641500019see below41500042.HD415000434150004441500045

1.1.

NS NS 2.3.4.5.6.7.8.9.

10.11.

ITEMNO.

PARTNUMBER DESCRIPTION ITEM

NO.PART

NUMBER DESCRIPTION

12.13.14.15.

16.17.18.19.20.21.22.23.24.

4150004641500030450000504150000141500072450001774500006345000064450000124500001545000044450001754150016441500103

Shaft CollarRocker BallNut, 3/8 - 16Pivot Ball,02/06-02/08Pivot Ball 03/08-Bolt, 3/8 - 16 x 1 3/4"Lock Washer, 3/8"Flat Washer, 3/8"Bolt, 1/4 - 28 x 2"Locknut, 1/4 - 28HandleBootAlignment ToolAlignment Tool

Unit Auto HDLCT600/6000 41500041.HDSCL800/60C 41500041A.HDLCT650 41500041B.HD

Item #7

Clip spring goes here

Clutch Assist Group

Clutch CylinderCylinder Support Bracket, JDCylinder Support Bracket, CaterpillarClutch Bracket ArmClutch Bracket Arm, Auto HDLinkage, Rod endLinkage, Threaded insertBearingPivot Shaft TubePivot Shaft Turb, Auto HDPivot Shaft, LCT600Pivot Shaft, LCT600, Auto HDPivot Shaft, SCL800 & LCT60CPivot Shaft, SCL800 & LCT60C, Auto HDPivot Shaft, LCT650PIvot Shaft, LCT650, Auto HDSpacer

400050.A400054.C3054.2160400054.A415000954150001941500019A400050.C14150004241500042.HD4150004141500041.HD41500041A41500041A.HD41500041B41500041B.HD400050.C2

1.2.

3.

4.

5.6.

7.

8.

ITEMNO.


Auto PTO- John Deere 4045D/T (11/00 - ); Caterpillar 2005 and after

Cat

Note: Auto HD is used on engines with 99HP or greater and other engines as an option. Started 08/22/05

THETHETHETHETHE

BLOWER HOUSING GROUP*Impeller & Blower Breakdown*Pedestal & Bearing Assembly*Exhaust Duct Assembly

BLO

WE

R H

OU

SIN

G G

RO

UP

800-446-9823


SKB700 BLOWER AND IMPELLER GROUP

1.2.3.4.5.6.7.

DESCRIPTIONITEMNO.

*Blower Housing BackLiner SetBearing PlateBolt-In LinerBoltNutRubber Seal

PARTNUMBER

SKB700.006*LCT620.602SCL800.201LCT620.602ALCT620.603LCT620.603NSCL800.202

8.9.10.11.12.13.14.

DESCRIPTIONITEMNO.

Impeller BushingBushing Key-Shaft ProtectorImpellerStraight Liner after 03/02Bolt, after 03/02Nut, after 03/02

PARTNUMBER

LCT650.601LCT650.601KLCT60.652LCT60.33LCT620.604LCT620.605LCT620.605N

*Please call ODB for part number as SKB's can have many different types of blower housings

1

2

3

4

5 6

7

8

910

11

12

1314

6

11

1211

SKB700 90 DEGREE Blower Housing Group2002 and after

Blower Housing Back, Belt drive onlyLiner SetBearing PlateCurved LinerLiner Bolt, 1/2-13 x 1-1/4 flat headLiner Nut, 1/2-13 ESN

SCL620.601.BDLCT620.602LCT600.602LCT620.602ALCT620.603LCT620.603N

1.2.3.4.5.6.

ITEMNO.


Note:

ImpellerBushing with boltsKey, straight 11/16" x 1/2 x 4"LShaft ProtectorBolt Straight Liner

LCT60.33LCT650.601LCT650.601FLCT600.6155CZ.500.750LCT620.604

7.8.9.

10.11.12.

ITEMNO.


3

4

56

710

1

2

9

8

5

SKB700 90 Degree Blower Housing Face GroupSingle Axis Units only, 2002 and after

Blower Housing 90 DegFace, single axis

Intake Swivel ElbowBearing for Swivel ElbowSupport BarSupport Bar BracketInspection DoorLimit SwitchHinge, Inspection Door

SCL621.601BDSCL875.001ASCL875.001SCL621.603SCL621.604SCL621.602LCT690.601.ALCT621.603

1.2.3.4.5.6.7.8.

ITEMNO.


Note: This assembly is for belt drive, single axis units only. Multiaxis belt drive units have a different face and no barrell assembly.

Boom BearingBoom BearingStop Pin Handle Assembly Pin Spring Handle Rod Grip End Cap

LCT616.801LCT616.801SCL670.2 SCL670.1 SCL670.3 SCL670.4 SCL670.5 SCL670.6

9.10.11.12.13.14.15.16.

ITEMNO.


3

4

5

6

8

7

11

10

1

2

12

13

16

14

159

SKB700 FUEL TANK GROUP

1.2.3.4.5.6.7.8.9.

DESCRIPTIONITEMNO.

Fuel Tank, all yearsFuel Cap and Gauge 07/1999 and after -Plastic tanksFuel Pick Up Tubes- plastics tanksGasket- plastic tanksFuel Strainer - plastic tanksFuel Tank Hold Down - Top - plastic tanksFuel Tank Hold Down - Bottom- plastic tanksFuel Tank Hold Down - Side - plastic tanksBolt-on Fuel Tank Frame Assembly

PARTNUMBER

SCL833.601P2SCL833.604ASCL833.606SCL833.607LCT633.617SCL833.631PSCL833.611PSCL833.621PSKB700.702

All Years - non-electric fuel gauge

*Units made before 7/1999 had steel tanks. These tanks are no longer available. A conversion kit must be purchased.

SKB700 90 DEGREE Exhaust Ducts Group2002 and after

Duct, 45 degree, approximately 45" long, 16.5"T x 14"WDuct,Straight, 96"Long x 16.5"T x 14"W(see note #2)Duct, 45 degree, approximately 29" long x 16"T x 14"W

SKB621.615SKB621.614SKB621.616

1.2.3.

ITEMNO.


Note: 1. Please measure your duct because we may have made one or more of the duct work specially for you. 2. One flange is only "tack" welded so that it can be custom placed in the field. Weld thoroughly once the flanged has been placed in the correct position for your application.

3

1

2

SKB700 Belt Drive Pedestal Group

1.2.3.4.5.6.7.8.9.10.11.12.

LCT609.602BLCT650.602.ALCT600.610LCT650.504LCT650.603.11LCT650.604LCT650.601KSCL850.606SKB700.003SKB700.005LCT609.602LCT650.602.C

PARTNUMBER

DESCRIPTIONITEMNO.

PedestalFlange BearingBearing PlateShaftPulleyBushingStep down KeyPower BandBelt GuardPedestal LidOvercenter LatchBearing Collar

BELT DRIVE UNITS ONLY

1

2

34 5

5

6

67

8

9

10

11

12

12

1

8

24

6

5

5

3

7

Single Axis units after April 1999Blower Housing Face Group - SKB700

1.2.3.4.5.6.7.8.

SCL700.007ASCL621.602LCT621.603LCT690.601.ALCT616.801LCT690.602SKB875.001ASCL875.001

PARTNUMBER

DESCRIPTIONITEMNO.

Blower Housing FaceInspection DoorInspection Door HingeLimit SwitchBoom BearingLimit Switch WireIntake Swivel Elbow, LHElbow Bearing

THETHETHETHETHE

HOSE BOOM GROUP*Hose Boom Assembly*Intake Hose Assembly*Hydraulic Pump Assembly

HO

SE

BO

OM

GR

OU

P

800-446-9823


LCT600/6000 Boom Group

Boom ArmBoom MastBoom CylinderBoom Mast BearingsUp/Down Switch AssemblyWiring Harness(w/ pushbuttons)

Push Buttons only SS Button Hold DownCylinder SleeveHold Down BracketBolt, 5/8" x 4"Hydraulic Hose, 64"Power Cord

LCT616.606ALCT616.605AMP-CS.150.12LCT616.801STD.2320STD.2321C*LCT616.611B*STD.2322LCT617.602LCT616.615DOD-5CZ.625.4.0LCT617.608600.2322

1.2.3.4.5.6.6a7.8.9.

10.11.12.

ITEMNO.


October 2009 - present

Brass BushingHydraulic PumpPump CoverPump SpacerFlow Control Valve90 degree fittingStraight FittingNutRocker Switch Push Button BoxHole CoverCover Plate,no cutoutHose Support BarCover Plate,cutout

RMB531MP-M259OD-259PCOD-200022LCT617.604OD-9405.4.4OD-9205.4.4OD-ZESNC.6254045.0021ASTD.2320STD.2323STD.2320ELCT616.607STD.2320D

13.14.15.16.17.18.19.20.21.22.23.24.25. 26.

ITEMNO.


Notes: * #6 includes #6a also. You can purchase just #6a however, if needed.

Intake Hose Group

1.

2.3.

4.5.

LC-MDH.16.120LC-MDH.16.100LCT616.601LCT616.616LCT60.645LCT616.603ULCT60.642

PARTNUMBER

(LCT60C, LCT600,LCT650, SCL800TM)

DESCRIPTIONITEMNO.

Intake Hose, except SCLIntake Hose, SCL800Intake NozzleHose Clamp, Bolt StyleHose Clamp, Quick Release (not shown)Hose SupportSupport Chain

1

2

3

3

4

5

PARTNUMBER(LCT6000)

LC-MDH.18.120

LCT616.601.18LCT616.618LCT60.645.18LCT616.603U.18LCT60.642

M259 Hydraulic Boom Pump

ITEM NO.2.

2a.2a.6.6.

23.27.31.32.

PART NUMBERMP-08053MP-08684MP-08711MP-03335MP-17744MP-03773MP-06231MP-00488MP-00496

Electric Motor, 12VBrush Set, 3 brushes & end cap 2001 and beforeBrush Set, 3 brushes & end cap 2002 and afterSolenoid Switch, 4 post, curved (controls up movement)Solenoid Switch, heavy dutyCord, Harness, 144" LongPlastic ReservoirElectric Valve, (controls down movement)Coil, 2 way- 2 position

*Call ODB for any part not listed.

DESCRIPTION

2a

SKB700 2 Axis Boom Assembly(March 2002 thru present)

Boom ArmBoom MastBearing, 2 requiredHydraulic Cylinder, In/OutPinHydraulic Cylinder,Up/Down90 Degree Hydraulic FittingFlow Control ValveBolt, 3/4-16 x 4.5" LongNut, 3/4"Hose Support Tube, 18"Intake NozzleHose BandHose Support

LCT616.606A2LCT616.605MA450.1406SCL816.810SCL816.814SCL816.812SCL816.502LCT617.504800.708800.712SCL816.813LCT616.601LCT616.616LCT616.603U

1.2.3.4.5.6.7.8.9.10.11.12.13.14.

ITEMNO.


Intake FlangeIntake Hose, standard dutyIntake Hose, medium dutyBolt, 3/4-16 x 7.5" LongNut, 3/4"Bolt, 3/4-16 x 5" LongNut, 3/4"Bolt, 5/8-11 x 4.5" LongNut, 5/8"Bushing, .75"IDx1"ODx1Bushing, .625"IDx.875"ODx1Bushing, .625"IDx.75"ODx.5Bushing, 1"IDx.375"ODx1

SCL875.002SDH.16.120.UCMDH.16.120800.710800.712800.709800.712800.711800.7138X.002E8X.002F8X.002D8X.002G

15.16.

17.18.19.20.21.22.23.24.25.26.

ITEMNO.


*All units are custom made, use numbers as a reference only.

2 Axis Boom Assembly - Geared Style (2005 thru present)

Boom Arm, Up/Down

Chain, specify # of linksStop BracketBoom MastFlange Bearing, topSprocket, 72 toothBushingHydraulic MotorSprocket, 24 toothFlange Bearing, bottomHydr. Cylinder, up/down90 Degree FittingFlow Control ValveCrossover Relief ValveChain. specify # of linksHose Nozzle, straightHose Nozzle, 90 degr.Hose Clamp

LCT616.606A2

No NumberSCL816.503800.707SCL816.501800.703SCL816.506800.701800.702SCL816.502SCL816.812HYF.1028LCT617.604800.705No Number6000.24076000.2408LCT616.618

1.2.3.5.6.7.8.9.

10.11.12.13.14.15.16.17.18.

18a.19.

ITEM # PART No. DESCRIPTIONHose Support BandIntake Hose, 10' LongHose Flange, straightHose Flange, 45 degreeGear CoverBearing BlockGasketBushing, .625"IDx.75"Dx.5Bushing, .75"IDx1"ODx1Bushing, .625"IDx.875"ODx1Bushing, 1"IDx.375"ODx1Bolt, 3/4-16 x 4.5"LongBolt, 3/4-16 x 5" LongBolt, 3/4-16 x 7.5" LongBolt, 5/8-11 x 4.5" LongNut, 3/4Nut, 5/8Lock Rod

LCT616.603U.18MDH.18.120LCT616.604.186000.2306800.706800.704800.704G8X.002D8X.002E8X.002F8X.002G800.708800.709800.710800.711800.712800.713LCT600.635.1

20.21.22.

22a.23.24.25.26.27.28.29.30.31.32.33.34.35.36.

ITEM #. PART No. DESCRIPTION*All units are custom made, use numbers as a reference only.

SKB700 3 Axis Boom Assembly - Geared Style (March 2002 thru present)

Boom Arm, Up/DownBoom Arm, In/OutHydraulic Cylinder, In/OutPinStop BracketBoom MastFlange Bearing, topSprocket, 72 toothBushingHydraulic MotorSprocket, 24 toothFlange Bearing, bottomHydr. Cylinder, up/down90 Degree FittingFlow Control ValveCrossover Relief ValveHose Support Tube, 18"Hose Support Tube, 24"Hose NozzleHose Clamp

LCT616.606MA.2LCT616.606MA.1SCL816.810SCL816.814SCL816.503800.707SCL816.501800.703SCL816.506800.701800.702SCL816.502SCL816.812HYF.1028LCT617.604800.705SCL816.813SCL816.813.24LCT616.601.MASCL816.604

1.2.3.4.5.6.7.8.9.

10.11.12.13.14.15.16.17.

18.19.

ITEMNO.


Hose Support BandIntake Hose, 10' LongIntake Hose, 12' LongHose FlangeGear CoverBearing BlockGasketBushing, .625"IDx.75"Dx.5Bushing, .75"IDx1"ODx1Bushing, .625"IDx.875"ODx1Bushing, 1"IDx.375"ODx1Bolt, 3/4-16 x 4.5"LongBolt, 3/4-16 x 5" LongBolt, 3/4-16 x 7.5" LongBolt, 5/8-11 x 4.5" LongNut, 3/4Nut, 5/8

LCT616.603U.BSDH.16.120.UCSDH.16.144.UCSCL875.002800.706800.704800.704G8X.002D8X.002E8X.002F8X.002G800.708800.709800.710800.711800.712800.713

20.21.

22.23.24.25.26.27.28.29.30.31.32.33.34.35.

ITEMNO.


*All units are custom made, use numbers as a reference only.

Hydraulic TankFiller CapHydraulic Filter Assembly Filter OnlyStraight Fitting to tank90 Degree FittingValve Body - complete Valve Body only Dead Man Cartridge Pressure Relief Valve Flow Control

LCT600.681TFCS.437W800.2003 800.2004

800.500B 800.500HF 800.502B 800.501B 800.506B

ITEMNO.


2 or 3X Hydraulic Tank - Valve Body Group

1.2.3.4.5.6.7.8.9.

10.11.

SKB700 multi-axis units - January 2006 and after

800.503B800.504B800.505B800.518B800.517B800.500W800.807STD.9015

ITEMNO.


12.13.14.15.16.17.18.19.20.

Cartridge AssemblySolenoid OnlyCartridge OnlyValve CoverValve Mounting FrameCartridge Wiring HarnessValve Body HarnessHydraulic Pump, 2XFitting, 90 degree

3X Hinged Boom Frame Assembly3 Axis units July 2005 and after

1.2.3.4.5.6.

ITEMNO.


This is the new "hinged - style" boom assembly. The units before July 2005 had a telescoping boom assembly. They are not interchangeable.

Upright FrameFrame Arm, rearFrame Arm, frontHinge PinBushing, uses 3Center Bracket

800.602A800.601A.R800.601A.L800.607800.608800.603A

4

3

1

2

5

6

800-446-9823


IMPROPER USE OF ANY MACHINE CANRESULT IN SERIOUS INJURY!

STUDY AND FOLLOW ALL SAFETYPRECAUTIONS BEFORE OPERATING OR

REPAIRING UNIT

5118 Glen Alden DriveRichmond, VA 23231

DO NOT ATTEMPT TO OPERATEOR REPAIR

THE LEAF COLLECTOR WITHOUT FIRSTREADING AND UNDERSTANDING THIS

MANUAL

IF YOU HAVE ANY QUESTIONS CONCERNING THEINSTALLATION OR OPERATION OF THIS UNIT, PLEASE CALL

ODB FOR ASSISTANCE BEFORE ATTEMPTING TO REPAIR OROPERATE THE UNIT.

THIS MANUAL IS AN INTEGRAL PART OF THE LEAF COLLECTOR ANDSHOULD BE KEPT WITH THE UNIT WHEN IT IS SOLD.

Documents

Xtreme cover1 - 165.22.183.63165.22.183.63/media/assets/manuals/SKB650-2009.pdf · Belt Driven Leaf Collector SKB700/650SKB700/650 ODB Company 5118 Glen Alden Drive Richmond, VA 23231