Upload
hoangdt8
View
224
Download
0
Embed Size (px)
Citation preview
7/28/2019 X LiteConfig HiRes
1/11
X-Lite Soft Phone Configuration
Revision Revised By Date
Initial Tigran Avanesov 22 Apr 2005
Quadro variants: All Quadro2x models, Quadro4x,Quadro16x
valid forSW-version:
tested withSW version:
Filename: X-Lite soft phone configuration.doc
Version: 0.0.1
Template: SupportTemplate.dot
Last saved: 5/3/2005 2:35 by
Abstract:This document describes how to configure X-Lite soft SIP phoneto work with Quadro.
Please Note: This document contains confidential and proprietary information owned by Epygi Technologies Ltd. Any copying, use or disclosure of thedocument or the information contained herein without the written permission of Epygi Technologies Ltd. is strictly prohibited.
7/28/2019 X LiteConfig HiRes
2/11
X-Lite Soft Phone Configuratio
Table of Contents:
1 Introduction...........................................................................32 Scenario................................................................................4
2.1Requirements and Preparations ...............................................42.1.1 Software .....................................................................42.1.2 Hardware ....................................................................4
3 Configuring X-Lite as an IP Line Extension..................................53.1IP Lines Configuration on the Quadro........................................53.2IP Lines Configuration on X-Lite ...............................................6
4 Configuring X-Lite as Remote Extension .....................................84.1SIP Remote Extension Settings Configuration on Quadro .............84.2SIP Remote Extension Settings Configuration on X-Lite ...............9
5 Additional Information ...........................................................115.1How to find out SIP Proxy UDP Port of the Quadro....................115.2Connecting to Quadros management site................................11
10 Aug. 05 CONFIDENTAL
7/28/2019 X LiteConfig HiRes
3/11
X-Lite Soft Phone Configuratio
1 Introduction
This document describes how to configure X-Lite soft SIP phone to work with Quadro as RemoteExtension. At first be sure that you are using latest version of X-Lite SIP phone. Download the latest
version at http://www.xten.com/. Install X-Lite SIP phone on your workstation and tune up the
microphone and speakers.
Fig. 1: X-Lite Soft IP Phone
Additional documentation about X-Lite may be found at http://www.xten.com/.
Please Note: All described below is tested with X-Lite v2.0 Build 1103m version.
10 Aug. 05 CONFIDENTAL
http://www.xten.com/http://www.xten.com/http://www.xten.com/http://www.xten.com/7/28/2019 X LiteConfig HiRes
4/11
X-Lite Soft Phone Configuratio
2 Scenario
2.1 Requirements and Preparations
2.1.1 SoftwareMicrosoft Windows
Please Note:Be attentive with the platform version. Download the correct X-Lite version for your
platform (MS Windows).
2.1.2 Hardware
PC, Sound Card, Microphone, Speakers
10 Aug. 05 CONFIDENTAL
7/28/2019 X LiteConfig HiRes
5/11
X-Lite Soft Phone Configuratio
3 Configuring X-Lite as an IP Line Extension
Connect your computer to the LAN side of the Quadro if you are configuring X-Lite as an IP Line
Extension. For connecting your PC to the Quadro refer to the Installation Guide for Quadro.
Click on the Menu button (see Fig. 1). In the displayed windows select System Settings. Then select
Network.
3.1 IP Lines Configuration on the Quadro
Connect to the Quadros management site (see point 5.2 Connecting to Quadros management site),then go to Telephony->Line Settings, click on IP Line Settings. Select a line and activate it by
selecting the SIP Phone radio button (Fig. 2). Fill the Username and Password fields (for example
login:xlite, password: xlite11). Then click Save.
Please note: The username from this page must be entered as the Username and the Authorization
User on the X-Lite soft phone and the password from this page as the Password on X-Lite.
Fig. 2: Quadro's IP Line Settings Page
10 Aug. 05 CONFIDENTAL
7/28/2019 X LiteConfig HiRes
6/11
X-Lite Soft Phone Configuratio
3.2 IP Lines Configuration on X-Lite
Fig. 3: Menu 1
1. Disable Auto Detect IP and enter your IP Address into the Listen on IP field(you have to seteither dynamic IP received from Quadros DHCP or static IP on your PC).
2. Set Use X-NAT to Choose SIP/RTP Ports to Never.
3. Leave NAT Firewall IP empty.
4. Enter your Quadro's LAN IP address (default: 172.30.0.1) into the Out Bound SIP Proxy andPrimary DNS fields.
5. Clear Provider DNS Server, Primary STUN Server, Secondary STUN Server and NAT
Firewall IP fields.
6. Set the other values as described in Fig. 3 Click the Back button and select SIP Proxy, then
select [Default].
10 Aug. 05 CONFIDENTAL
7/28/2019 X LiteConfig HiRes
7/11
X-Lite Soft Phone Configuratio
Fig. 4: Menu 2
7. Set the Enabled field to Yes.
8. Enter your phone name (any text, for example your name) into the Display Name field.
9. Enter your Username and Authorization User as Quadros IP Line Username and
Password as Quadros IP Line password (see point4.1 IP Lines Configuration on Quadro).
10.Enter your Quadro's IP address into the Domain/Realm, SIP Proxy, Out Bound Proxy fields(y default 172.30.0.1) and close configuration menu.
Now, your X-Lite soft IP Phone will register on the Quadro as an IP Line.
Please Note:Quadros default LAN IP address is 172.30.0.1 and the default SIP listen udp port is5060. If they differ on your Quadro from the default, you should enter the correct IP address and the
correct SIP listen udp-port of your Quadro. To view the SIP Proxy UDP port see point 5.1 How to findout SIP Proxy UDP Port of the Quadro
If your LAN IP address is for example 172.30.0.50 and your SIP Proxy UDP port is 3344, you need to
enter 172.30.0.50 into the Domain/Realm field, 172.30.0.50:3344into theSIP Proxy field andinto the Out Bound Proxy field.
10 Aug. 05 CONFIDENTAL
7/28/2019 X LiteConfig HiRes
8/11
X-Lite Soft Phone Configuratio
4 Configuring X-Lite as Remote Extension
4.1 SIP Remote Extension Settings Configuration on Quadro
Connect to Quadros management site (see point 5.2 Connecting to Quadros management site), then
go to Users->User Management and Extension Settings.
Select an extension and edit it.
On the User Management - Edit Entry page enable the SIP Remote Extension feature by checking
the Enable checkbox (Fig. 5).
Enter the Username and the Password into the corresponding fields (for example login:xlite,password: xlite11). Then click on the Save button.
Open your Internet browser and connect to Quadro's management site by entering Quadros IP address
as web URL. Enter admin login and password. Then go to Telephony->Line Settings and click on IPLine Settings. Select a line and activate it by selecting SIP Phone radio button (Fig. 4).
Please Note: The Username entered here must be used as Username and Authorization User onthe X-Lite soft phone, too, and the Password entered here as the Password on the X-Lite softphone.
You my also enable the Enable RTP proxy checkbox if needed.
Fig. 5: User Management - Edit Entry page
10 Aug. 05 CONFIDENTAL
7/28/2019 X LiteConfig HiRes
9/11
X-Lite Soft Phone Configuratio
4.2 SIP Remote Extension Settings Configuration on X-Lite
Fig. 6: Menu 1
1. Disable Auto Detect IP and enter your IP Address into the Listen on IP field (you have to set
either dynamic IP received from Quadros DHCP or static IP on your PC.2. Set Use X-NAT to Choose SIP/RTP Ports to Never.
3. Leave NAT Firewall IP empty or ask your network administrator what has to be filled in.
4. Set the Primary DNS field to your subnet DNS server IP address (ask your network
administrator if you don't know this IP address)
5. Clear Provider DNS Server, Secondary STUN Server and NAT Firewall IP fields.
6. Also fill any STUN server name and port number (for example stun.epygi.com:3478) into the
Primary STUN Server field. Be sure that NAT is enabled on your default gateway (ask yournetwork administrator). If your computer is behind a firewall be sure that the Listen SIP Port
and Listen RTP port features are enabled by network administrator.
7. Set the other values as described in Fig. 6. Click the Back button and select SIP Proxy, thenselect [Default].
10 Aug. 05 CONFIDENTAL
7/28/2019 X LiteConfig HiRes
10/11
X-Lite Soft Phone Configuratio
Fig. 7: Menu 2
8. Set the Enabled field to Yes.
9. Enter your phone name (any text, for example your name) into the Display Name field.
10.Enter your Username and Authorization User as Quadros Username, and Password asQuadros Password (see point4.1 SIP Remote Extension Settings Configuration on Quadro).
11.Enter your Quadro's IP address into the Domain/Realm, SIP Proxy, Out Bound Proxy fieldsand close configuration menu.
Now, your X-Lite soft IP Phone will register on the Quadro as a SIP IP Line/Remote Extension.
Please note: Quadros default SIP Listen udp-port is 5060. If they differ from the default on your
Quadro, you should enter the correct IP address and the correct SIP listen udp-port of your Quadro. Toview the SIP Proxy UDP port, see point 5.1 How to find out SIP Proxy UDP Port of the Quadro.
If your WAN IP address is for example 212.30.0.50 and your SIP Proxy UDP port is 3344, you need to
enter 212.30.0.50 into the Domain/Realm fieldand 212.30.0.50:3344 into the SIP Proxy field.
10 Aug. 05 CONFIDENTAL 1
7/28/2019 X LiteConfig HiRes
11/11
X-Lite Soft Phone Configuratio
5 Additional Information
5.1 How to find out SIP Proxy UDP Port of the Quadro
Connect to the Quadro management site by entering Quadros LAN IP address as web URL. Enter the
administrator login and the password. To see the SIP Proxy UDP portclick the SIP Settings menu itemof the Telephony menu.
5.2 Connecting to Quadros management site
Open your Internet browser and connect to Quadro's management site by entering Quadros IP addressas web URL. Enter admin login and password.
10 Aug 05 CONFIDENTAL 1