Vehicle Classification by means of Inductive Loop Detectors and Light Detection and Ranging Technology

Dan BrandeskyNEXTRANS Intern, Ohio State University

Internship Overview

Internship focused on vehicle classification Use of new techniques applied to existing

technologies– Precise vehicle classification through LIDAR imaging

process– Length-based classification through use of freeway

loop detector impulse data Internship only partially completed due to later

start date (OSU still on quarter system)

LIDAR Overview

LIDAR = Light Detection and Ranging Works on same principle as radar, but uses

ultraviolet or infrared light– Shorter wavelengths of light provide much greater

accuracy than radar LIDAR units can be used to produce a data

“image” of an object Units scan in single axis (horizontal or vertical)

LIDAR Animation LIDAR unit contains a

laser, reflected outward by a rotating mirror, shown in the top box

Unit detects obstructions in the laser’s path, shown in the middle box

Processed data is shown in the bottom box (converted from polar to Cartesian coordinates)

Image Source: http://en.wikipedia.org/wiki/File:LIDAR-scanned-SICK-LMS-animation.gif

LIDAR-Equipped Van

Honda Odyssey minivan outfitted with one front and one rear LIDAR unit, and two driver’s side LIDAR units– Front LIDAR scan horizontally, side LIDAR scan

vertically Van also has one front and one rear camera, and a

driver’s side view camera– Video data is then synchronized and cross-referenced

with LIDAR data during processing to develop algorithms for vehicle classification

LIDAR-Equipped Van

LIDAR Research Currently working with MATLAB-based software

tool to classify vehicular LIDAR detector data by category:

•Cars

•Small SUVs

•SUVs

•Pickups

•Buses

•Small/Large Single Unit Trucks

•Small/Large Dual Unit Trucks

•Motorcycles/Bicycles

Use of LIDAR allows for more specific vehicle classification than normal FHWA “axle count” methods– Finer resolution of data– More accurate data for traffic surveys, etc.

LIDAR Data Collection

Data is collected while van is being driven– Several pre-defined routes are used to give multiple

data sets for single routes– As van is driven, differential GPS unit logs van’s

location so that video and LIDAR data can be synced with a map of the route during processing

At termination of a route, data is downloaded from the van computer and transferred to the campus server

LIDAR Data Processing

MATLAB-based processing tool Two modes of operation:

– Ground Truth Manually compare video and corresponding LIDAR data to

determine if detected objects are indeed vehicles, or if they are other objects (e.g. pedestrians)

– Vehicle Classification Manually re-process objects defined in earlier step as vehicles

into more specific categories mentioned in previous slide

LIDAR Data ProcessingGround Truth Mode

LIDAR Data ProcessingVehicle Classification Mode

LIDAR Detection•Top image is stock photo of very similar vehicle to the one shown in the LIDAR image

•LIDAR figure is clear enough to discern axles and vehicle’s windows, and height and depth measurements (Y and Z axes, in meters) give even more information about detected vehicle

•From LIDAR data alone, it is clear that this is not just a conventional pickup truck

•Allows for more accurate data with fine resolution

Image Source: http://isuzu.sqserver.com/nprhd_vs_gm_c4500_16500.htm

Inductive Loop Detector Overview

Inductive loops are wire loops buried in pavement, connected to an inductive loop detector in the controller cabinet

Detector is “tuned” to normal inductance of loop, and when a vehicle passes over the loop, the loop inductance changes, and the detector sends and impulse to the controller

Single loop detector stations (one per lane) are typically deployed on freeways for real time traffic monitoring

Inductive Loop Detectors in Vehicle Classification

Currently, only dual-loop detector stations (meaning a station with two loops per lane, one after the other) are used for classifying vehicles and measuring speed

Single loop detectors normally cannot classify vehicles because of differences in vehicle speeds and lengths– A long vehicle moving quickly could appear the same as a

shorter vehicle moving slowly Developing the ability to use single loop detectors for

vehicle classification is significant because there are many more single loops than dual loops, so it provides useful data from existing detectors– Less implementation cost to municipalities

Single-Loop Vehicle Classification Research

Developing software algorithms for single loop detectors to classify vehicles by vehicle length

Working to refine accuracy of algorithm– Began with simple categories: short, medium, and long

Currently working with software tool to develop more specific categories by comparing loop detector impulse data from specific stations with video from adjacent traffic cameras– Measure vehicle length in pixels with software tool, which matches loop

detector impulses with correct video frames Loop data is not always accurate due to various erroneous

detections– Vehicles changing lanes cause impulses in two detectors by one vehicle– Incorrectly operating detectors may detect vehicles in adjacent lanes as

well as their own lanes

Single-Loop Vehicle Classification Data Processing

Work In Progress

Continue to process LIDAR data Work more with inductive loop vehicle

classification Learn more about programming of

MATLAB software tools Continue to collect data for analysis to

improve precision of classification algorithms