VANS GYPLAST Wall Block Plaster€¦ · Also needs putty application of 1 to 2 mm before applying paint. Gypsum Based Plaster Made of gypsum and lighter in weight. It gives ready

VANS GYPLAST Wall Block Plaster

Types of hard surface

Brick Wall Cement Block wall Concrete Wall

VANS Gyplast can be applied directly in all of above hard surfaces

Types Of Block Plaster

Cement Based PlasterMade of white cement and dolomite with various additives. Such plasters are heavy by weight and can not meet the requirement of thick application. Also needs putty application of 1 to 2 mm before applying paint.

Gypsum Based PlasterMade of gypsum and lighter in weight. It gives ready surface for painting but some time it still needs some amount of smoothening plaster for hiding purpose. It all depends upon the skill of plasterer.

Introducing

Vans Gyplast™

• Vans Gyplast is a pure gypsum based plaster suitable for most internal wall & partition surfaces including brick, block and concrete.

• It consists essentially of pure gypsum hemihydrateformulated with special additives to control working and setting characteristic.

• It contains pure gypsum in natural form also eliminated from all impurities.

• It gives plaster an unmatched workability because of its smoothness, coverage and ease of application. It dries to provide super white, smooth and fine finish for painting.

OUR USPs

• Vans Gyplast is the only gypsum plaster which is very natural in its form and gives a ultra white and bright finish. It’s smoothness gives great coverage, workability and high productivity to the plasterer. Hence great wall finish with reduced time and cost to the customer. This is how we add value to our customer’s business.

• Lightweight

• Excellent strength on drying

• Thermal resistance

• Good coverage

• Affordable

• Humidity resistant

• Crack free

• No powdering

• Fungus Free

• Fire resistant

Other Features

• Can be directly applied, single coat application.• Free from shrinkage and crack and powdering• High coverage up to 92 m2/t• Ultra white and smooth finish• Enhanced light reflection, imparts true colour tone and gloss for

paint.• Compatible with any type of paint.• Highly moisture resistant• Hygienic -Does not allow bacteria or fungus getting formed on it.• Available in 25 Kg• Thickness can go up to 32 mm.• 6 months Shelf life.

Technical Details

Parameters Dry Bulk

Density

Wet Bulk

Density

Initial

Setting

Time

Final

Setting

Time

Compressive

Strengths

(24 Hours)

Compressive

Strengths

(48 Hours

Approx.

Coverage*

Units 667-695

Kg/m3

1.32 – 1.46

gm/cm3

14-18

Minutes

24-26

Minutes

43.80

kgf/cm2

44.12

kgf/cm2

87-92 m2/t

Physical Property

Chemical PropertyParameters Silicon

dioxide

(SIO2)

Aluminum

Oxide

( AI203)

Iron(III)

oxide

(Fe203)

Calcium

Oxide

(CaO)

Diphosporus

Pentoxide

(P205)

Manganese

oxide

(Mn0)

Sulfur

Trioxide

(So3)

Sodium

oxide

(Na2O)

Potassium

oxide

(K2O)

Loss On

Ignition

(L.O.I)

Units 0.07% n.d. n.d. 38.80% n.d. n.d. 54.60% 0.01% 0.01% 5.72%

n.d. = Less than distinguish limit

Recommended Application Methodology

Step 1:

The wall surface (Substrate)

to be plastered should be

thoroughly clean with a

brush to be free from all dust

and loose particles. If any

traces of mould oil must be

washed with detergent

water.


Step 2:It is recommended to pre

wet the substrate before

application so as to get

the substrate fully

hydrated to achieve

strong adhesion, more

spread and better

coverage.


Step 3:Measure the surfaceundulation with plumb threadand fix level mosaic (Tiki) in order to estimate amount ofplaster required and spread plaster on the wall to achieveabsolutely plain surface withzero undulation.


Step 4:Mix Vans Gyplast to water (Notvise versa), using mixing rod to mixpaste thoroughly to get desiredconsistency.

Step 5 :Water to plaster ratio should be maintainedto have good cohesive workable mix (1 Part of water : 1 part of plaster by volume).

However this ratio can be adjusted by the applicator depending upon site climatic condition.


Step 6:Prepare plaster mix asmuch as requireddepending uponimmediate scope ofwork.

# Precautiononce the mix has begun to set,additional dry material should not beadded, as performance parametersof plaster will get altered, thusaffecting applicability, consistency,adhesion & strength.


Step 7:

Apply mixed plaster on the

substrate with a hand trowel

and level it with aluminium

bottom scale. Avoid using a

wet brush on the finished

surface, as that would leave

permanent brush marks and

spoil the surface.


Step 8:

single coat should not exceed

12mm in thickness. If at all

thickness required more than

12 mm, plaster should be

applied in multiple coats.


Step 9:

After the complete drying (which

usually takes 72 hrs dependingon

the thickness and whether

conditions) levelled Vans Gyplast

surface is ready for painting.

Safety Instruction

Vans Gyplast is absolutely

free from any lime and toxic

elements. In case it comes in

contact with eye or live

wound, needs to be cleaned

with fresh normal water.

Consult your doctor if

irritation continues

Product Comparison Chart

Products Comparision

Directapplication

Line &level

Smoothfinish

Timesaving

Qualityassurance

Watercuring

Shrinkagecracks

Sand cement Plaster

√ – – – – √ √

POP – √ √ – – Does not

require√

Gypsum Plaster √ √ √ √ √Does not

require

Do not

appear

Benefits to Builders

1. Green material

2. Quality offering to his customer - Shrinkage crack free surfaces - smooth finish

3. High productivity – faster work (Reducing plastering time by 70% when compared to conventional Sand cement plaster + POP method) so time saving and cost

4. No water curing required.

5. Performance – Durability, light weight (Reduces dead load on structure)

6. Cleaner sites - direct application bagged product

Benefits to Applicator

1. Easy to apply with smooth and consistent paste – Increased efficiency and saves time.

2. Enhanced coverage – better per day productivity.

3. Smooth and super white finish – customer appreciation & work satisfaction

4. 100% natural product without any lime content – safe, non hazardous to skin and health.

5. Also available in Quick setting formulation –efficient workability in cold and moist climatic condition.

Benefits to End User

1. No shrinkage cracks on walls and ceilings

2. Reduction in the time required for plastering and this helps in timely possession of homes

3. Perfectly lined, leveled, smooth walls

4. Saving on electricity used for air conditioning as gypsum has very low thermal conductivity

TEST CERTIFICATE

Packaging

VANS Gyplastis available in

25KG Bag

Thanking You !

Documents

VANS GYPLAST Wall Block Plaster€¦ · Also needs putty application of 1 to 2 mm before applying paint. Gypsum Based Plaster Made of gypsum and lighter in weight. It gives ready