VANS GYPLAST Wall Block Plaster
Types of hard surface
Brick Wall Cement Block wall Concrete Wall
VANS Gyplast can be applied directly in all of above hard surfaces
Types Of Block Plaster
Cement Based PlasterMade of white cement and dolomite with various additives. Such plasters are heavy by weight and can not meet the requirement of thick application. Also needs putty application of 1 to 2 mm before applying paint.
Gypsum Based PlasterMade of gypsum and lighter in weight. It gives ready surface for painting but some time it still needs some amount of smoothening plaster for hiding purpose. It all depends upon the skill of plasterer.
Introducing
Vans Gyplast™
• Vans Gyplast is a pure gypsum based plaster suitable for most internal wall & partition surfaces including brick, block and concrete.
• It consists essentially of pure gypsum hemihydrateformulated with special additives to control working and setting characteristic.
• It contains pure gypsum in natural form also eliminated from all impurities.
• It gives plaster an unmatched workability because of its smoothness, coverage and ease of application. It dries to provide super white, smooth and fine finish for painting.
OUR USPs
• Vans Gyplast is the only gypsum plaster which is very natural in its form and gives a ultra white and bright finish. It’s smoothness gives great coverage, workability and high productivity to the plasterer. Hence great wall finish with reduced time and cost to the customer. This is how we add value to our customer’s business.
• Lightweight
• Excellent strength on drying
• Thermal resistance
• Good coverage
• Affordable
• Humidity resistant
• Crack free
• No powdering
• Fungus Free
• Fire resistant
Other Features
• Can be directly applied, single coat application.• Free from shrinkage and crack and powdering• High coverage up to 92 m2/t• Ultra white and smooth finish• Enhanced light reflection, imparts true colour tone and gloss for
paint.• Compatible with any type of paint.• Highly moisture resistant• Hygienic -Does not allow bacteria or fungus getting formed on it.• Available in 25 Kg• Thickness can go up to 32 mm.• 6 months Shelf life.
Technical Details
Parameters Dry Bulk
Density
Wet Bulk
Density
Initial
Setting
Time
Final
Setting
Time
Compressive
Strengths
(24 Hours)
Compressive
Strengths
(48 Hours
Approx.
Coverage*
Units 667-695
Kg/m3
1.32 – 1.46
gm/cm3
14-18
Minutes
24-26
Minutes
43.80
kgf/cm2
44.12
kgf/cm2
87-92 m2/t
Physical Property
Chemical PropertyParameters Silicon
dioxide
(SIO2)
Aluminum
Oxide
( AI203)
Iron(III)
oxide
(Fe203)
Calcium
Oxide
(CaO)
Diphosporus
Pentoxide
(P205)
Manganese
oxide
(Mn0)
Sulfur
Trioxide
(So3)
Sodium
oxide
(Na2O)
Potassium
oxide
(K2O)
Loss On
Ignition
(L.O.I)
Units 0.07% n.d. n.d. 38.80% n.d. n.d. 54.60% 0.01% 0.01% 5.72%
n.d. = Less than distinguish limit
Recommended Application Methodology
Step 1:
The wall surface (Substrate)
to be plastered should be
thoroughly clean with a
brush to be free from all dust
and loose particles. If any
traces of mould oil must be
washed with detergent
water.
Recommended Application Methodology
Step 2:It is recommended to pre
wet the substrate before
application so as to get
the substrate fully
hydrated to achieve
strong adhesion, more
spread and better
coverage.
Recommended Application Methodology
Step 3:Measure the surfaceundulation with plumb threadand fix level mosaic (Tiki) in order to estimate amount ofplaster required and spread plaster on the wall to achieveabsolutely plain surface withzero undulation.
Recommended Application Methodology
Step 4:Mix Vans Gyplast to water (Notvise versa), using mixing rod to mixpaste thoroughly to get desiredconsistency.
Step 5 :Water to plaster ratio should be maintainedto have good cohesive workable mix (1 Part of water : 1 part of plaster by volume).
However this ratio can be adjusted by the applicator depending upon site climatic condition.
Recommended Application Methodology
Step 6:Prepare plaster mix asmuch as requireddepending uponimmediate scope ofwork.
# Precautiononce the mix has begun to set,additional dry material should not beadded, as performance parametersof plaster will get altered, thusaffecting applicability, consistency,adhesion & strength.
Recommended Application Methodology
Step 7:
Apply mixed plaster on the
substrate with a hand trowel
and level it with aluminium
bottom scale. Avoid using a
wet brush on the finished
surface, as that would leave
permanent brush marks and
spoil the surface.
Recommended Application Methodology
Step 8:
single coat should not exceed
12mm in thickness. If at all
thickness required more than
12 mm, plaster should be
applied in multiple coats.
Recommended Application Methodology
Step 9:
After the complete drying (which
usually takes 72 hrs dependingon
the thickness and whether
conditions) levelled Vans Gyplast
surface is ready for painting.
Safety Instruction
Vans Gyplast is absolutely
free from any lime and toxic
elements. In case it comes in
contact with eye or live
wound, needs to be cleaned
with fresh normal water.
Consult your doctor if
irritation continues
Product Comparison Chart
Products Comparision
Directapplication
Line &level
Smoothfinish
Timesaving
Qualityassurance
Watercuring
Shrinkagecracks
Sand cement Plaster
√ – – – – √ √
POP – √ √ – – Does not
require√
Gypsum Plaster √ √ √ √ √Does not
require
Do not
appear
Benefits to Builders
1. Green material
2. Quality offering to his customer - Shrinkage crack free surfaces - smooth finish
3. High productivity – faster work (Reducing plastering time by 70% when compared to conventional Sand cement plaster + POP method) so time saving and cost
4. No water curing required.
5. Performance – Durability, light weight (Reduces dead load on structure)
6. Cleaner sites - direct application bagged product
Benefits to Applicator
1. Easy to apply with smooth and consistent paste – Increased efficiency and saves time.
2. Enhanced coverage – better per day productivity.
3. Smooth and super white finish – customer appreciation & work satisfaction
4. 100% natural product without any lime content – safe, non hazardous to skin and health.
5. Also available in Quick setting formulation –efficient workability in cold and moist climatic condition.
Benefits to End User
1. No shrinkage cracks on walls and ceilings
2. Reduction in the time required for plastering and this helps in timely possession of homes
3. Perfectly lined, leveled, smooth walls
4. Saving on electricity used for air conditioning as gypsum has very low thermal conductivity
TEST CERTIFICATE
Packaging
VANS Gyplastis available in
25KG Bag
Thanking You !