Upload
trinhque
View
218
Download
0
Embed Size (px)
Citation preview
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-6656 1 - 1
TOOL MAINTENANCE & REPAIR INFORMATION
AMERICAN PNEUMATIC TOOL
Check BEFORE, DURING AND AFTER useof APT tools.
FIELD OPERATION:
Before:1. Fill the oil reservoir with Air Tool oil or 10W
equivalent.2. Tighten nuts on the side rod bolts.3. Check for play in fronthead with tool steel.
Replace hex bushing if worn.4. Check all nuts to ensure they are tight on the
tool.5. Replace retainer if worn6. Clean any water and/or dirt from air hose before
connecting it to the tool.
During:1. For your safety and that of others, keep tool
against work at all times!2. When moving from one work area to another,
shut off tool.3. Never run tool when steel bit is not against
work.4. Do not use tool as a wedge or prying instru-
ment.5. Refill oil reservoir approximately every two
hours.6. Check all nuts to ensure they are tight on the
tool.
After:1. Flush tool with cleaning solvent, then refill with
Air Tool oil or 10W grade equivalent.2. Do not leave tool in water or in dirt.
3. Check all nuts to ensure they are tight on thetool.
4. Store the tool well oiled.TROUBLE SHOOTING GUIDE
If the tool runs erratically:1. Check all nuts to ensure they are tight on the
tool.2. Flush cleaning solvent through the tool and then
refill immediately with Air Tool oil or 10W gradeequivalent.
3. If tool still runs erratically, disassemble andcheck the cleanliness of the valves. In addition,check for plugged cylinder ports.
If the tool has an air leakage around thebackhead:1. Disassemble and inspect the backhead to see if
the throttle valve or “o”ring seal is damaged.2. Tighten up all backhead nuts securely.
If the breaker is not hitting hard enough:1. Check all nuts to ensure they are tight on the
tool.2. If all nuts are tight, then check for wear on inter-
nal parts, if worn, parts should be replaced.3.Check clearances between piston and cylinder
very carefully.
If you cannot shut off the tool:1. Immediately turn off air source, then disconnect
air supply.2. Disassemble backhead and inspect the throttle
valve and “o” rings for damage.
APT
PAVING BREAKERS
REMEMBER: PREVENTIVE MAINTENANCEWILL ASSURE MAXIMUMPERFORMANCE FROM ALL OF YOUR APT TOOLS.
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-6656 1 - 3
AMERICAN PNEUMATIC TOOL
MODEL 117PAVING
BREAKERThis 30 lb. class Paving Breaker is an ideal tool forlight to medium demolition work as well as for usein confined areas. This lightweight tool can teardown concrete or brick walls, break up concretefloors, or be used in any other type of generaldemolition work.
FEATURES■ Automatic v alve■ Drop f orged allo y steel handle■ Built-in automatic oiler■ Replaceab le chuc k bushing■ Rubber handle grips■ Latc h type retainer■ Swivel hose connection■ Noise dampening m uffler a vailab le■ Four -bolt bac khead
SPECIFICATIONSPart Chuck Size Bore Stroke BPM CFM Weight Length Air Inlet
Number inches @ 90 PSI lbs. inches NPTinlet pressure
5199 7/8 x 3-1/4 1-3/4 3-3/8 1850 34-38 33 21-3/4 3/8 male5200 1 x 4-1/4 1-3/4 3-3/8 1850 34-38 33 21-3/4 3/8 male
rev 1/99APT
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-66561 - 4
AMERICAN PNEUMATIC TOOL
APT
193PISTON
194FRONTVALVE
195REARVALVE
197GUIDE
1556SPRING
199PIN
2332(4)NUT
196VALVE
6812(4)BOLT
*3571CYLINDER
9067(inc. 191)9068 (inc. 192)
CYLINDERASSY
6332CYLINDER 6333
CYLINDERASSY
3573BUSHING
FORMER CONSTRUCTION
207PLUNGER
6331CONE
6331CONE
WASHER
2949SPRING
6334BOLT
3134BOLT
3123HOUSING
6335WASHER 208
NUT
2332NUT
893RETAINER
191 (7/8" HEX x 31/4")192 (1" HEX x 41/4")
BUSHING
* FOR REFERENCE ONLY (THESE PARTS NOT SOLD SEPARATELY)
3143HOUSING ASSY
9350GRIP
111PLUG108
PLUG
2000SPRING
6825O-RING
4357 Backhead Assy Includes:106 bushing (1), 111 plug (1), 112 felt (1), 4356 backhead (1).
105PIN
112FELT
132LEVER
9350GRIP 7526
HANDLE KIT
1815NUT
1814O-RING
1816SWIVELASSY
*2482SWIVEL
1817SPRING
106BUSHING6810
VALVE ASSY
7647O-RING
*6808VALVE
1827SCREEN
*4356BACKHEAD
•4357BACKHEAD
ASSY
APT MODEL 117PAVING BREAKER
PART NO. 5199 (7/8" HEX x 3-1/4")PART NO. 5200 (1" HEX x 4-1/4")
7526HANDLE KIT
566O-RING
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-6656 1 - 5
APT
The Model 140 is a rugged, yet lightweight, Paving Breakerdesigned for light to medium construction work. It is ideallysuited for plant maintenance work, such as light demolitionof floors, pavement, frozen ground and masonry walls. Thistool is also very popular for bridge deck jobs.
AMERICAN PNEUMATIC TOOL
MODEL 140PAVING
BREAKER
FEATURES■ Automatic v alve■ Drop f orged allo y steel handle■ Built-in automatic oiler■ Rubber handle grips■ Latc h type retainer■ Swivel hose connection■ Noise dampening m uffler a vailab le■ Four -bolt bac khead
SPECIFICATIONSPart Chuck Size Bore Stroke BPM CFM Weight Length Air Inlet
Number inches @ 90 PSI lbs. inches NPTinlet pressure
17923 1x 4-1/4 1-7/8 4-1/4 1500 48 43 21-1/8 1/2 male
1 - 6
AMERICAN PNEUMATIC TOOL
APT MODEL 140PAVING BREAKER
PART NO. 17923
17958GRIP (2)
17940THROTTLE LEVER
1380ROLL PIN (2)
17955NUT (4)
3508THROTTLE
VALVE ASSY 3528THROTTLE
VALVE
3224SEAL
3225RETAINING
RING
17954LOCK WASHER (4)
3215OIL PLUG
17975OIL PLUG
17928SPACER
17924VALVE ASSY
17950SEAL
17951AIR INLET
SWIVEL2225O-RING
10081O-RING
17944AIR INLET
NUT
17948PISTON
17952CYLINDER
17949BOLT
17935BOLT (2)
598SPRING
111PLUG
17925VALVE CASE
17957O-RING
17927VALVE
17926COVER
17934SPRING (2)
17933LOCK-NUT (2)17936
NUT (2)
6284PLUNGER 18228
BOLT
2897SPRING
205WASHER
6235RETAINER
LATCH
17930BUSHING
18226FRONTHEAD
208NUT
17942BACKHEAD
17946TAPPET BUSHING
17945TAPPET
17939BACKHEAD ASSY.
18227FRONTHEAD ASSY
178SCREEN
rev. 5-99
APT
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-6656 1 - 7
AMERICAN PNEUMATIC TOOL
MODEL140A
AIRGO-Line™
PAVINGBREAKER
The Model 140A Airgo-Line is a 40 lb. class PavingBreaker. The ergonomically designed handle absorbs theexcess harmful vibration to the hands and arms of theoperator. This versatile tool can be converted into a classic40 lb. Paving Breaker in minutes by just switching theergonomic handle for a standard one. This tool is excellentfor light to medium demolition work and concrete breaking.
FEATURES■ AIRGO-Line TM Ergonomic bac khead
(inter chang eable with standar d handle)
■ Less vibration doesn’t mean less power, it deliver s the same hitting power as the standar d Model
■ By reducing operator fatigue ,efficienc y and output is increased
■ Automatic v alve■ Built-in automatic oiler■ Latc h type retainer
SPECIFICATIONSPart Chuck Size Bore Stroke BPM CFM Weight Length Air Inlet
Number inches @ 90 PSI lbs. inches NPTinlet pressure
18041 1x 4-1/4 1-7/8 4-1/4 1500 48 43 21-1/8 1/2 male
rev 1/99
APT
APT MODEL 140A AIRGO-Line PAVING BREAKER TM
PART NO. 18041
17928 SPACER
17924 VALVE ASSY
17951 AIR INLET SWIVEL2225
O-RING
10081 O-RING
17944 AIR INLET
NUT
17948 PISTON
17952 CYLINDER
17949 BOLT
17935 BOLT (2)
111 PLUG
17925 VALVE CASE
17957 O-RING
17927 VALVE
17926 COVER
17934 SPRING (2)
17933 LOCK-NUT (2)17936
NUT (2)
6284 PLUNGER
2897 SPRING
17937 ROLL PIN (OUTER)
6235 RETAINER
LATCH
17930 BUSHING
17931 FRONTHEAD
17938 ROLL PIN (INNER)
17946 TAPPET
BUSHING
17945 TAPPET
17929 FRONTHEAD ASSY
178 SCREEN
18034 AIRGO-NOMIC™
BACKHEAD ASSY
102 (4) WASHER
121 (4) NUT
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-66561 - 8
AMERICAN PNEUMATIC TOOL
APTrev 1/99
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-6656 1 - 9
APT
The model 160, a 60 lb. class Paving Breaker,is a hard-hitting tool that can be used for mediumto heavy demolition work and concrete breaking.The 160 is the perfect all-around breaker and oneof the best tools on the market for asphalt cuttingapplications.
AMERICAN PNEUMATIC TOOL
MODEL 160PAVING
BREAKER
FEATURES■ Automatic v alve■ Drop f orged allo y steel handle■ Built-in automatic oiler■ Replaceab le chuc k bushing■ Rubber handle grips■ Latc h type retainer■ Swivel hose connection■ Noise dampening m uffler a vailab le■ Four -bolt bac khead
SPECIFICATIONSPart Chuck Size Bore Stroke BPM CFM Weight Length Air Inlet
Number inches @ 90 PSI lbs. inches NPTinlet pressure
5235 1-1/8 x 6 2-1/4 4-1/8 1680 60-65 68 25-3/4 1/2 male5236 1-1/4 x 6 2-1/4 4-1/8 1680 60-65 68 25-3/4 1/2 male
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-66561 - 10
AMERICAN PNEUMATIC TOOL
APT
APT MODEL 160PAVING BREAKER
PART NO. 5235 (1-1/8"HEX)PART NO. 5236 (1-1/4" HEX)
*167 NUT
3414NUT ASSY
3307O-RING
*1107SWIVEL
179SWIVELASSY
1269O-RING
178SCREEN
170FRONTVALVE
239 (4)BOLT
171REARVALVE
169GUIDE
113PLUNGER
160GRIP
106BUSHING
6275SEAL
102 (4)WASHER
121 (4)NUT
6810VALVEASSY
7647O-RING
*6808VALVE
107SPRING
114SPRING
6290BACKHEAD
6176BACKHEAD
ASSY160
GRIP
108PLUG
105PIN
132LEVER
111PLUG
112FELT
6176 Backhead Assy includes:106 Bushing, 111 Plug, 112 Felt, 6290 Backhead
174PISTON
1124 (2)BOLT
1777 (3)PLUG
*773CYLINDER
173CYLINDER
ASSY
104VALVE
115PIN
566O-RING
129NUT 101
WASHER
127CONE
126PLUNGER
125SPRING
130RETAINER
625 (1-1/8" HEX x 6")1912 (1-1/4" HEX x 6")
BUSHING
* 3017HEAD
127CONE
180 (1-1/8" HEX x 6")181 (1-1/4" HEX x 6")
HEAD ASSY
619BOLT
110 (2)NUT
138(2)WASHER
109 (2)SPRING
262TAPPET
175BUSHING
* FOR REFERENCE ONLY(THESE PARTS NOT SOLD SEPARATELY)
182 (1-1/8" HEX x 6")183 (1-1/4" HEX x 6")FRONTHEAD ASSY
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-6656 1 - 11
The Model 160 Airgo-Line is a 60 lb. class Paving Breaker.The ergonomically designed handle absorbs the excessharmful vibration to the hands and arms of the operator.This versatile tool can be converted into a classic 60 lb.Paving Breaker in minutes by just switching the ergonomichandle for a standard one. This tool is excellent for mediumto heavy demolition work and concrete breaking.
AMERICAN PNEUMATIC TOOL
MODEL 160AAIRGO-Line™
PAVINGBREAKER
FEATURES■ AIRGO-Line TM Ergonomic bac khead
(inter chang eable with standar d handle)
■ Less vibration doesn’t mean less power, it deliver s the same hitting power as the standar d Model
■ By reducing operator fatigue ,efficienc y and output is increased
■ Automatic v alve■ Built-in automatic oiler■ Latc h type retainer
SPECIFICATIONSPart Chuck Size Bore Stroke BPM CFM Weight Length Air Inlet
Number inches @ 90 PSI lbs. inches NPTinlet pressure
17746 1-1/8 x 6 2-1/4 4-1/8 1680 60-65 87 28-1/4 1/2 male17747 1-1/4 x 6 2-1/4 4-1/8 1680 60-65 87 28-1/4 1/2 male
rev 1/99APT
rev 1/99
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-66561 - 12
AMERICAN PNEUMATIC TOOL
APT
APT MODEL 160AAirgo-Line™
PAVING BREAKER
PART NO. 17746 (1-1/8"HEX)PART NO. 17747 (1-1/4" HEX)
*167 NUT
3414NUT ASSY
3307O-RING
*1107SWIVEL
179SWIVELASSY
1269O-RING
178SCREEN
170FRONTVALVE
17750 (4)BOLT
171REARVALVE
169GUIDE
113PLUNGER
6275SEAL
102 (4)WASHER
121 (4)NUT
114SPRING
174PISTON
1124 (2)BOLT
1777 (3)PLUG
*773CYLINDER
173CYLINDER
ASSY
104VALVE
115PIN
566O-RING
127CONE
262TAPPET
175BUSHING
129NUT 101
WASHER
126PLUNGER
125SPRING
130RETAINER
625 (1-1/8" HEX x 6")1912 (1-1/4" HEX x 6")
BUSHING
* 3017HEAD
127CONE
180 (1-1/8" HEX x 6")181 (1-1/4" HEX x 6")
HEAD ASSY
619BOLT
110 (2)NUT
138(2)WASHER
109 (2)SPRING
* FOR REFERENCE ONLY(THESE PARTS NOT SOLD SEPARATELY)
182 (1-1/8" HEX x 6")183 (1-1/4" HEX x 6")FRONTHEAD ASSY
17684AIRGO-Line™
BACKHEAD ASSY
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-6656 1 -13
APT
Tough and dependable, the high performancemodel 180 is the most powerful air tool APTmakes. It is designed for big jobs such as heavydemolition and concrete breaking. Since themodel 180 has the ability to penetrate the hardestconcrete it is the tool of choice for road buildingand foundation removal.
AMERICAN PNEUMATIC TOOL
MODEL 180PAVING
BREAKER
FEATURES■ Automatic v alve■ Drop f orged allo y steel handle■ Built-in automatic oiler■ Replaceab le chuc k bushing■ Rubber handle grips■ Latc h type retainer■ Swivel hose connection■ Noise dampening m uffler a vailab le■ Four -bolt bac khead
SPECIFICATIONSPart Chuck Size Bore Stroke BPM CFM Weight Length Air Inlet
Number inches @ 90 PSI lbs. inches NPTinlet pressure
5237 1-1/8 x 6 2-5/8 6-1/8 1350 75-80 93 29 3/4 male5238 1-1/4 x 6 2-5/8 6-1/8 1350 75-80 93 29 3/4 male
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-66561 - 14
AMERICAN PNEUMATIC TOOL
APTrev. 11-98
APT MODEL 180PAVING BREAKER
PART NO. 5237 (1-1/8"HEX)PART NO. 5238 (1-1/4" HEX)
*103 NUT
3373NUT ASSY
1188O-RING
* 323SWIVEL
124SWIVELASSY
151O-RING
123SCREEN
141FRONTVALVE
239 (4)BOLT
117REARVALVE
116GUIDE
113PLUNGER
160GRIP
106BUSHING
6180SEAL
102 (4)WASHER
121 (4)NUT
6810VALVEASSY
7647O-RING
*6808VALVE
107SPRING
114SPRING
6280BACKHEAD
6187BACKHEAD
ASSY160
GRIP
108PLUG
105PIN
132LEVER
111PLUG
112FELT
6187Backhead Assy includes:106 Bushing, 111 Plug, 112 Felt, 6280 Backhead
118PISTON
1124 (2)BOLT
1743 (3)PLUG
*755CYLINDER
140CYLINDER
ASSY
104VALVE
115PIN
129NUT 101
WASHER
127CONE
126PLUNGER
125SPRING
130RETAINER
625 (1-1/8" HEX x 6")1912 (1-1/4" HEX x 6")
BUSHING
* 2996HEAD
127CONE
163 (1-1/8" HEX x 6")164 (1-1/4" HEX x 6")
HEAD ASSY
619BOLT
110 (2)NUT
138 (2WASHER
109 (2)SPRING
1381TAPPET
1382BUSHING
* FOR REFERENCE ONLY(THESE PARTS NOT SOLD SEPARATELY)
165 (1-1/8" HEX x 6")166 (1-1/4" HEX x 6")FRONTHEAD ASSY
566O-RING
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-6656 1 - 15
The Model 180A Airgo-Line is a 80 lb. class PavingBreaker. The ergonomically designed handle absorbs theexcess harmful vibration to the hands and arms of theoperator. This versatile tool can be converted into a classic80 lb. Paving Breaker in minutes by just switching theergonomic handle for a standard one. This tool is excellentheavy demolition work and concrete breaking.
AMERICAN PNEUMATIC TOOL
MODEL 180AAIRGO-Line™
PAVINGBREAKER
FEATURES■ AIRGO-Line TM Ergonomic bac khead
(inter chang eable with standar d handle)
■ Less vibration doesn’t mean less power, it deliver s the same hitting power as the standar d Model
■ By reducing operator fatigue ,efficienc y and output is increased
■ Automatic v alve■ Built-in automatic oiler■ Latc h type retainer
SPECIFICATIONSPart Chuck Size Bore Stroke BPM CFM Weight Length Air Inlet
Number inches @ 90 PSI lbs. inches NPTinlet pressure
18160 1-1/8 x 6 2-5/8 6-1/8 1350 75-80 90 31 3/4 male18161 1-1/4 x 6 2-5/8 6-1/8 1350 75-80 90 31 3/4 male
rev 1/99
APT
rev 1/99
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-66561 - 16
AMERICAN PNEUMATIC TOOL
APT
APT MODEL 180AAIRGO-LineTM
PAVING BREAKER PART NO. 18160 (1-1/8"HEX)
PART NO. 18161 (1-1/4" HEX)
*103 NUT
3373NUT ASSY
1188O-RING
* 323SWIVEL
124SWIVELASSY
151O-RING
123SCREEN
141FRONTVALVE
239 (4)BOLT
117REARVALVE
116GUIDE
113PLUNGER
114SPRING
118PISTON
1124 (2)BOLT
1743 (3)PLUG
*755CYLINDER
140CYLINDER
ASSY
104VALVE
115PIN
129NUT 101
WASHER
127CONE
126PLUNGER
125SPRING
130RETAINER
625 (1-1/8" HEX x 6")1912 (1-1/4" HEX x 6")
BUSHING
* 2996HEAD
127CONE
163 (1-1/8" HEX x 6")164 (1-1/4" HEX x 6")
HEAD ASSY
619BOLT
110 (2)NUT
138 (2WASHER
109 (2)SPRING
1381TAPPET
1382BUSHING
* FOR REFERENCE ONLY(THESE PARTS NOT SOLD SEPARATELY)
165 (1-1/8" HEX x 6")166 (1-1/4" HEX x 6")FRONTHEAD ASSY
REF6180SEAL
102 (4)WASHER
121 (4)NUT
17720 AIRGO-Line™BACKHEAD ASSY
rev 1/99
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-6656 1 - 17
The Model Airgo-Line handle assembly is designedto be a vibration dampening handle. The ergonomi-cally designed handle absorbs at least 50% of theharmful vibration to the hands and arms of theoperator. These versatile handle assemblies caneasily be adapted to the standard APT Model 140,160, and 180 Paving Breakers by removing andreinstalling the four backhead nuts and bolts.
AMERICAN PNEUMATIC TOOL
MODELS140A/160A/180A
PAVING BREAKER
AIRGO-Line™
HANDLE
FEATURES■ Vibration dampening
ergonomic handledesigned to absorb theshoc k to the operator
■ Handles areinter chang eable withAPT Models 140, 160,and 180; now you canconver t your standar dAPT tool into anergonomic model inmin utes
160GRIP
17689RIGHT
HANDLE
17688RIGHT HANDLE
ASSY
17685BUSHING
17709 (2)SPIRAL PIN
17696SPRING17699
VALVE
17705THROTTLE
VALVEASSY
17698DOWEL PIN
17716BUSHING 17708
GASKET
17693THROTTLE
LEVER
17691LEFT HANDLE
ASSY
17711(2)THROTTLE STOP
17710 (2)SPIRAL
PIN
17692LEFT
HANDLE
160GRIP
16189 (2)PIPE PLUG
112FELT
17697SPRING
18032BACKHEAD
17685BUSHING
17707COVER
2129O-RING
17695OIL PLUG
17712 (4)CAP SCREW
6414 (4)LOCK WASHER
1980PLUG
18033BACKHEAD ASSY
(INCLUDES:18032 BACKHEAD,
17716 BUSHING)
APT MODEL 140AAirgo-Line
PART NO. 18034BACKHEAD ASSY
160GRIP
17689RIGHT
HANDLE
17688RIGHT HANDLE
ASSY
17685BUSHING
17709 (2)SPIRAL PIN
17696SPRING17699
VALVE
17705THROTTLE
VALVEASSY
17698DOWEL PIN
17716BUSHING 17708
GASKET
17693THROTTLE
LEVER
17691LEFT HANDLE
ASSY
17711 (2)THROTTLE STOP
17710 (2)SPIRAL
PIN
17692LEFT
HANDLE
160GRIP
16189 (2)PIPE PLUG
112FELT
17697SPRING
18094BACKHEAD
17685BUSHING
17707COVER
2129O-RING
17695OIL PLUG
17712 (4)CAP SCREW
6414 (4)LOCK WASHER
1980PLUG
17719BACKHEAD ASSY
(INCLUDES:18094 BACKHEAD,
17716 BUSHING)
6275SEAL
APT MODEL 180AAirgo-LineTM
PART NO. 17720BACKHEAD ASSY
160GRIP
17689RIGHT
HANDLE
17688RIGHT HANDLE
ASSY
17685BUSHING
17709 (2)SPIRAL PIN
17696SPRING17699
VALVE
17705THROTTLE
VALVEASSY
17698DOWEL PIN
17716BUSHING 17708
GASKET
17693THROTTLE
LEVER
17691LEFT HANDLE
ASSY
17711 (2)THROTTLE STOP
17710 (2)SPIRAL
PIN
17692LEFT
HANDLE
160GRIP
16189 (2)PIPE PLUG
112FELT
17697SPRING
17714BACKHEAD
17685BUSHING
17707COVER
2129O-RING
17695OIL PLUG
17712 (4)CAP SCREW
6414 (4)LOCK WASHER
1980PLUG
17715BACKHEAD ASSY
(INCLUDES:17714 BACKHEAD,
17716 BUSHING)
6275SEAL
APT MODEL 160AAirgo-LineTM
PART NO. 17684BACKHEAD ASSY
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-6656
AMERICAN PNEUMATIC TOOL
APT