Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
Triple Wardrobe(Product Code AP06)
Step By Step Assembly Instructions
Pre-Assembly Preparation1. Please check the pack contents before attempting to assemble
this product.A full checklist of components is given in this
leaflet.If any components are missing,please contact the retailer
from whom you bought this product.
2. This product is HEAVY,it should be assembled as near as
possible to the point of use.TAKE CARE WHEN LIFTING to avoid
personal injury and(or)damage to the product.
3. This product takes approximately 1 HOUR to assemble with 3 PEOPLE.
4. The fitting pack contains SMALL ITEMS which should be KEPT AWAY
FROM YOUNG CHILDREN.
5. Read this leaflet in full before commencing assembly.
6. We recommend that you lay a protective cloth on your carpet
during assembly,to prevent marking.Page 1
A
B
CD
EL F
G
H
I
J
K
L
Door Frame
Plinth Base LH Side Panel
Top CorniceF1E1D
C 1B 11A RH Side Panel
Hanging Rail 1
G 1Back Panel ShelfH 1 I
J K L
M
Rail supports 4
2016mm Screw(3*16)6330mm CSK ScrewsShelf Pins 20
16mm Screw(4*16) 26
1
Hanging Rail 1 Shelf 4
N P
Q R 3
Upright panel
WedgeS 2Hinge
Page 2
T Middle Door 1
N x 17
N
A
-Locate the centre upright panel and the side panels onto the plinth base by
using six 30mm CSK screws firstly.Then keep the another three 30mm screws.
Step 1
-With the aid of an assistant,locate the door frame(D)onto the wardrobe
as shown.Secure using 30mm CSK screws.Then pull the frame tightly
against the side panels and center panel and secure the frame from the
bottom upwards,using the 30mm CSK screws per side inserted through the
wooden block,also secure the frame to the unit base using the angled
holes provided in the rear of the bottom rail.
Step 2
Page 3
Fittings
Fittings
N
A
B
C
IN x 6
N x 3
N x 11
N
N
N x 23
-Before attaching the back panel(G),move the wardrobe close to the position where
it will be used.With uneven floors you may need to lean the wardrobe slightly left
or slightly right to ensure that the doors remain squre.With the aid of an
assistant,hold the wardrobe in position and secure the back panel to the rear of
the wardrobe.Finally,tighten all twenty-three 30mm screws(N).
Step 3 -With the aid of an assistant,locate the top cornice (F)as shown.Secure using
eleven 30mm screws.Also keep the another three 30mm screws.
Step 4
Page 4
Fittings
Fittings
N x 3
P x 20
M x 20
Q x 8
H
E
M
K
J
-Push fit twenty shelf pins(N)and locate the shelves(H&K)as shown,noting
that they are "Notched"at the rear corners.Secure using twenty 16mm
screws(R) for each shelf pin to fix the shelf.Also locate the two hanging
rails(E&J) and the hanging rail supports(L).
Step 6
Step 5 -Firstly using the screws position the hinges onto the middle door as shown,then
locate the middle door onto the upright side panel.The assembly is now completed.
Page 5
Fittings
Fittings
Q
T
Q x 18
L
Q
L x 4
-If necessary,adjust the door hinges as shown.The assembly is now completed. Step 7
Page 6
90cm Bedstead(Product Code AP01)
135cm Bedstead(Product Code AP02)
150cm Bedstead(Product Code AP03)
Step By Step Assembly InstructionsPre-Assembly Preparation
1. Please check the pack contents before attempting to assemble
this product.A full checklist of components is given in this
leaflet.If any components are missing,please contact the retailer
from whom you bought this product.
2. This product is HEAVY,it should be assembled as near as possible
to the point of use.TAKE CARE WHEN LIFTING to avoid personal injury
and(or)damage to the product.
3. This product takes approximately 45 MINUTES to assemble with 2 PEOPLE.
4. The fitting pack contains SMALL ITEMS which should be KEPT AWAY
FROM YOUNG CHILDREN.
5. Read this leaflet in full before commencing assembly.
6. You will require a crosshead screwdriver,an open ended spanner.
Page 1
A
B
C
D
E
F
F
C
A 1 1B 2C
D 1 E 1 F
32
34
135cm bedstead
150/180cm bedstead
Slat
Side RailFootboardHeadboard
Centre Rail
ThreadG 8 8H Nut Washer I Plastic Cap
(Provided with slats)
68
135cm bedstead
150/180cm bedstead
64
Centre Rail Support
SpannerJ 1
Page 2
A
G x 8
B
G
H x 4
C
C
H
Step 1 -Screw the eight threads into the headboard and footboard and tighten
by hand.Ensuring that there is enough thread remaining for attachment
in step 2 and 3.
Fittings
Step 2
Fittings
-Locate the side rails onto the threads protruding from the
headboard.Locate the washer and nut onto the threads and secure
by hand at first.Tighten using the open ended sapnner.
Please note.
The holes in the slat support
rail should be facing upwards.
Page 3
H
H x 4
A
B
D
E
Step 3 -Locate the side rails onto the threads protruding from the
footboard.Locate the washers and nuts onto the threads and secure
by hand at first.Tighten using the open ended spanner.
Fittings
-Attach the centre rail support to the centre rail as follows.Step 4
Page 4
A
B
D
E
D
I
F
150/180cm bedstead I x 68
135cm bedstead I x 64
-Locate the centre rail into the bottom rail of headboard and
footboard.Also adjust the centre foot as shown.
Step 5
E
Step 6 -Push fit two plastic caps onto either end of the slat.Push fit the slat into the
pre-drilled pilot holes.Please note that it may require a light tap with a soft
hammer to secure the plastic end caps into the holes.Repeat this step with the
remaining slats.The assembly is now completed.
Fittings
Page 5
Double Wardrobe(Product Code AP05)
Step By Step Assembly Instructions
Pre-Assembly Preparation
1. Please check the pack contents before attempting to assemble this product.A full
checklist of components is given in this leaflet.If any components are missing,please
contact the retailer from whom you bought this product.
2. This product is HEAVY,it should be assembled as near as possible to the point of
use.TAKE CARE WHEN LIFTING to avoid personal injury and(or)damage to the product.
3. This product takes approximately 1 HOUR to assemble with 3 PEOPLE.
4. The fitting pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
5. Read this leaflet in full before commencing assembly.
6. We recommend that you lay a protective cloth on your carpet during assembly,to
prevent marking.
Page 1
16mm Screw(4*16) 4
4 16mm Screw(3*16)
M
48 L30mm CSK ScrewsShelf Pins K4J
Rail supportsI 21H ShelfBack Panel 1G
1Hanging Rail
RH Side PanelA 1 1B 1C
D 1 E 1 F Top Cornice
LH Side PanelPlinth Base
Door Frame
面板
A
B
C
D
EIF
G
H
WedgeN 2
Page 2
L
K x 16
C
A
B
K x 6
D
-With the aid of an assistant,locate the side panels(B&C)into the plinth
base(A),noting that the battens on the side panels should be to the
rear.Secure using six 30mm screws.Inserted at an angle through the rear
edges of the panels.
Step 1
-With the aid of an assistant,locate the door frame(D)onto the wardrobe
as shown.Pull the frame tightly against the side panels and secure the
frame from the bottom upwards,using five 30mm screws(K) per side
inserted through the wooden block.Also Using the 30mm screws secure the
frame to the unit base using the angled holes provided in the rear of
the bottom rail.
Step 2
Fittings
Fittings
Page 3
L
K x 16
K x 10
K
K
-Before attaching the back panel(G),move the wardrobe close to the position
where it will be used.With uneven floors you may need to lean the wardrobe
slightly left or slightly right to ensure that the doors remain square.With
the aid of an assistant,hold the wardrobe in position and secure the back
panel to the rear of the wardrobe.Finally,tighten all sixteen 30mm screws(K).
Fittings
Step 4
Fittings
-With the aid of an assistant,locate the top cornice (F)as shown.Secure
using ten 30mm screws.
Step 3
Page 4
F
M x 4
J x 4
L x 4
H
E
J
IFittings
Step 5 -Push fit four shelf pins(J)and locate the shelves(H)as shown,noting that they are "Notched"at the rear corners.Secure using four 16mm
screws(L) for each shelf pin to fix the shelf.Also locate the hanging
rails(E) and the hanging rail supports(I).
Page 5
M
I x 2
90cm Bedstead(Product Code AP01)
135cm Bedstead(Product Code AP02)
150cm Bedstead(Product Code AP03)
Step By Step Assembly InstructionsPre-Assembly Preparation
1. Please check the pack contents before attempting to assemble
this product.A full checklist of components is given in this
leaflet.If any components are missing,please contact the retailer
from whom you bought this product.
2. This product is HEAVY,it should be assembled as near as possible
to the point of use.TAKE CARE WHEN LIFTING to avoid personal injury
and(or)damage to the product.
3. This product takes approximately 45 MINUTES to assemble with 2 PEOPLE.
4. The fitting pack contains SMALL ITEMS which should be KEPT AWAY
FROM YOUNG CHILDREN.
5. Read this leaflet in full before commencing assembly.
6. You will require a crosshead screwdriver,an open ended spanner.
Page 1
180cm Bedstead(Product Code AP04)
A
B
C
D
E
F
F
C
A 1 1B 2C
D 1 E 1 F
32
34
135cm bedstead
150/180cm bedstead
Slat
Side RailFootboardHeadboard
Centre Rail
ThreadG 8 8H Nut Washer I Plastic Cap
(Provided with slats)
68
135cm bedstead
150/180cm bedstead
64
Centre Rail Support
SpannerJ 1
Page 2
A
G x 8
B
G
H x 4
C
C
H
Step 1 -Screw the eight threads into the headboard and footboard and tighten
by hand.Ensuring that there is enough thread remaining for attachment
in step 2 and 3.
Fittings
Step 2
Fittings
-Locate the side rails onto the threads protruding from the
headboard.Locate the washer and nut onto the threads and secure
by hand at first.Tighten using the open ended sapnner.
Please note.
The holes in the slat support
rail should be facing upwards.
Page 3
H
H x 4
A
B
D
E
Step 3 -Locate the side rails onto the threads protruding from the
footboard.Locate the washers and nuts onto the threads and secure
by hand at first.Tighten using the open ended spanner.
Fittings
-Attach the centre rail support to the centre rail as follows.Step 4
Page 4
A
B
D
E
D
I
F
150/180cm bedstead I x 68
135cm bedstead I x 64
-Locate the centre rail into the bottom rail of headboard and
footboard.Also adjust the centre foot as shown.
Step 5
E
Step 6 -Push fit two plastic caps onto either end of the slat.Push fit the slat into the
pre-drilled pilot holes.Please note that it may require a light tap with a soft
hammer to secure the plastic end caps into the holes.Repeat this step with the
remaining slats.The assembly is now completed.
Fittings
Page 5