Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
[email protected] | www.key.net
The Small Piece Remover (SPR) is
an open-bed design machine with
integral frame and endless sizing belt,
used to separate smaller pieces of
product from line flow.
The machine is factory set at a six-
degree slope from infeed to discharge.
The belt uses molded, food-grade
plastic slats with pockets to perform
sizing. Running at a right angle to
product flow, the sizing belt forms
a trough where product travels
through the machine. The rolling
cross-flow movement gently mixes and
encourages product transfer.
Small pieces settle into the plastic
pockets in the belt, are lifted out of
the main product stream, and are
then discharged over the side of the
machine.
Small Piece RemoverApplications• Manufactured baby whole carrots, sugar snap peas,
edamame \ soy beans, and frozen green beans.
• Applications currently using a rotary separator.
• Small to medium size product that can be sized when
two of three dimensions fit into a sizing pocket and
can be lifted away from line flow.
98 Percent EffectiveThe mixing action ensures that target-size pieces contact
the sizing slats and are removed. Field operation has
resulted in 98% removal of target size pieces. Almost no
large pieces are removed with the targeted pieces.
Lower CostsThe SPR’s streamlined design can trim operating costs and
increase profit over alternative rotary-style separators. Its
carefully designed pockets are self-cleaning, eliminating
the need for high-pressure water and a motor to
continuously clean pockets. The simple, open framework
dramatically reduces clean-up and service time and
complexity. The compact design trims installation costs by
using less plant area and simplifying installation.
Sizing Pockets Side Discharge
[email protected] | www.key.net
Specifications and InformationCapacity:
Varies with product and specific requirements;
typical ranges between 8,800 to 20,000 lb/hr
(4,000 to 9,075 kg/hr)
Target Size:
Varies with product. Standard pocket size for
baby whole carrots is for separation of pieces
less than 1-1/2” (38 mm) in length and less than
1” (25.4 mm) in diameter.
Efficiency:
Capable of 98% or greater
Style:
Open frame with legs
Construction:
Stainless steel, food grade
Motor/Gearbox:
1 HP (0.75 kW)
FLOW
621.3 24 716 "
GRADED PRODUCTDISCHARGE HEIGHT
2605.1 102 916 "
991.1 39"INFEED HEIGHT REF
6° DOWNSLOPE
1495.6 58 78 "
OVERALL HEIGHT
1098.6 43 14 "
485.1 19 18 "
INFEED WIDTHMOTOR AND GEARBOX
2904.9 114 38 "
OVERALL LENGTH
2420.3 95 516 "
SMALL PIECE DISCHARGE
1252.4 49 516 "
OVERALL WIDTH
31.8 1 14 "
40.6 1 58 "
A
A
19.1 34 "
SECTION A-ATYPICAL POCKET GEOMETRY
REV. DESCRIPTIONREVISIONS
A LAYOUT
C
D
E
FF
E
D
C
54321
1 2 3 4 5 6 7 8
B
A
B
A
86 7
HANDLINGDRAWING TO BE INTERPRETED PER ASME Y14.5
This drawing, including the principles of design, is submitted with the agreement that it is not to be reproduced, copied or loaned in part or whole. It is not to be used in any manner that may constitute a detriment directly or indirectly to Key Technology, Inc.
FARMCO SPR SMALL PIECE REMOVER RH DIS
DESIGNER DESIGN-1STATUS:
SPR_RH SPR1-032969
2018-03-29
SPR_RH_MarketingSHEET 1 OF 1SCALE: 1:8
DOC NO.
DESCRIPTION:
FARMCO
ITEM NUMBER:
JLINDSAY
--
REVREF MODEL:
MODIFIED
DCHECKED
APPROVED
mm/kg
MFG ENG
EQP CATEGORY:
UNITS:
WHEN PRINTED FULL SCALE
DOC CTRL
DRAFTER JLINDSAY 2018-03-29
MASS: 520.2kg
x: ±2 x.x: ±1.5 x.xx: ±1.00 x.xxx: ±0.250 ANGLES: ±1
GENERAL TOLERANCESUNLESS OTHERWISE SPECIFIED
31.8 (1-1/4”)
40.6 (1-5/8”)
19.1 (3/4”)
1098.6 (43-1/4”) 2605.1 (102-9/16”)
6º Downslope
Motor and Gearbox485.1 (19-1/8”) Infeed Width
1252.4 (49-5/16”) Overall Width
2904.9 (114-3/8”) Overall Length
2420.3 (95-5/16”) Small Piece Discharge
991.1 (39”) Infeed Height Ref 621.3 (24-7/16”)
Graded Product Discharge Height
1495.6 (58-7/8”) Overall Height
REV 200410