Sender TsSKB - wischnew/pamela/internal/daq/ResursPamel… · Sender TsSKB Subject: Electro-Diagnostic Test of PAMELA RH Prot N° Year # of pages R1.d.1 377bis 03 103 Receiving data

Sender TsSKB

Subject: Electro-Diagnostic Test of PAMELA RH

Prot N° Year # of pages

R1.d.1 377bis 03 103

Receiving data Transmitting data 11/06/03

353П-46КС-27895-1105 1

APPROVED

TsSKB General Designer

First Deputy

____________ G.E. Fomin

"___"________ 2003

Electro-Diagnostic Test

Of “Pamela” RH in article 46КС

353П-46КС-27895-1105

Leading Designer

______________ V.N. Zjabchuk

"___"__________ 2003

Section 1107, Chief Section 1105, Chief

______________ Sh.Z Dusaev _____________ V.M. Federov

"___"__________ 2003 "___"_________ 2003

Section 1402, Chief

_______________ Ya.A. Mostovoy

"___"__________ 2003

Section 1405, Chief

_______________ S.A. Kustov

"___"___________ 2003

Section 1406, Chief

_______________ A.S. Kolpashikov

"___"___________ 2003

2003

353П-46КС-27895-1105 2

TABLE OF CONTENTS

Introduction………………………..………………………………

1. Indication of safety measures...…………………………………

2. Types of hardware testing …......…………….…………………

3. Tests of the hardware as part of the article ……………………

3.1 Purposes and tasks of the tests.………………………………...

3.2 Tests support .................……………………………………….

3.3 Evaluation of test results ...........……………………………….

3.4 GTE composition …………………………………………………….

4. Test activations of "Pamela" RH with support systems of the article

4.1 Procedure of PAM TA .................……………………………….

4.1.1 Procedure of PAM TA fragment 1 – "RH test"…......................

4.1.2 Procedure of PAM TA fragment 2 – "Technological opera-

tion"………………….............................................................…

4.1.3 Procedure of PAM TA fragments 3, 4 – "GS

test"...........................................………………………………………

4.2 Procedure of PAM/HSRL TA.………………………

4.2.1 Procedure of PAM/HSRL TA fragment 1 – "Nominal operation,

standby electronics test"………

4.2.2 Procedure of PAM/HSRL TA fragment 2 – "Test of HSRL communi-

cation channels"......................………………………………………….

5. Joint Operation of Pamela and HSRL .............................................

6. Integrated tests of Pamela ...............................................................

7. Amount of Pamela’s retesting after replacement of its components or

replacement of “Resource DK” SC...............................................

8. Estimation of operating time ……………………………………

9. Order of Pamela’s activation, deactivation and re-set......................………………………………………….…..

Annex 1. List of test programs.

353П-46КС-27895-1105 3

INTRODUCTION

The document on electro-diagnostic testing of "Pamela" RH summarizes

the scope and procedure of electrical testing of "Pamela" RH in article 46КС and is

the initial data for development of documentation on integrated electrical testing of

the article.

The present document was developed according to:

“Materials on "Pamela" RH control logic” (353П-46КС-26166-1105).

LIST OF ACRONYMS

RH – research hardware;

TA – testing activation;

JO – joint operation;

IT – integrated testing;

CD – computer data;

TM – telemetry;

SI – signaling information;

BCS – on-board computer system;

BTCS – on-board time-coordinate synchronizer;

CRPDS – command relay/power distribution system;

GV–global variable

PSS –power supply system;

OBE HSRL – on-board equipment of high speed radio link;

CMS – command measuring system;

BDTS – on-board data telemetry system;

FTD – flight time diagram

User – user (cosmodrome);

GTC – ground testing complex;

TP – technological prototype;

353П-46КС-27895-1105 4

FP – flight prototype;

Terminal – terminal;

PSCU – Pamela storage & control unit;

GSE – ground support equipment;

GTE – ground testing equipment;

RM –route marking;

TRD – transmission radiation detector;

MCMD – CC transmitted to the equipment by MCL;

GTE – ground testing equipment.

353П-46КС-27895-1105 5

1. INDICATION OF SAFETY MEASURES

Operation with "Pamela" RH is allowed to persons acquainted with mode

of functioning, structure of the article, operational documentation for the testing

equipment, trained in safety measures and entitled to work with electric facilities

of voltage below 1000 V in a group of 3 minimum and also entitled to work with

high-pressure vessels.

Operating personnel shall be acquainted with and observe the rules and

service instructions for instruments used for operations with the article and

also other rules and instructions in force at the manufacturing plant and at

the user’s.

353П-46КС-27895-1105 6

2. TYPES OF HARDWARE TESTING

At 46КС article manufacturing plant ("Progress" plant) electrical testing of

"Pamela" RH both for technological and flight prototypes are carried out in the fol-

lowing phases:

- prior installation on the article – incoming test using "Pamela" RH GSE

according to documentation developed in INFN.

- after installation on the article:

1. Test activations with the article’s support systems including:

a) equipment serviceability checkout;

b) test of communications with BCtS, CRPDS, BTMS, BTCS;

c) test of communications with HSRL OBE using technological output of

TDM commutator.

2. Joint operation with HSRL OBE.

3. Integrated testing (IT).

Measurement of interference level and slump of voltage in supply circuits

is carried out for the technological prototype.

The consequence of testing flight prototype of "Pamela" RH at the user’s is

the same.

Diagram of work with technological and flight prototypes of "Pamela" RH

at the “Progress” plant and at the user’s is given in Figure 0.

353П-46КС-27895-1105 7

Installation oftechnological prototype inSC PC

TA, JO, IT with technologi-cal prototype (2 cycles)

Activities on measuringmagnetic fields levels

Testing at the "Progress" plant

Incoming test oftechnological pro-totype

Incoming test of flightprototype

Dismounting oftechnological prototype

Instal. of flightprototype intoSC PC

TA, JO, IT with flight prototype (2 cycles)

Dismantling of flight prototype

Testing at the "Progress" plant

Instal. of flightprototype intoSC PC

TA, JO, IT with flight pro-totype (2 cycles)

Autonomous testing of flight proto-type within the scope of incoming test(external examination of RH and GSmono-units)

Test at the user’s

Meas interf level&volt slump

Figure 0. Diagram of work with TP and FP of "Pamela" RH at the "Progress" plant and at the user’s.

353П-46КС-27895-1105 8

3. TESTS OF THE HARDWARE AS PART OF THE ARTICLE

3.1 Purposes and tasks of the tests.

The purpose of electrical testing of "Pamela" RH as part of the article is to

confirm its serviceability as part of the article and availability for operation in ac-

cordance with its mission.

Tasks of the electrical testing of the hardware as part of the article are as

follows:

а) testing accuracy of hardware/46КС article systems connections;

б) testing the hardware serviceability including checkout of: PSCU, Termi-

nal, basic and standby protection units (PU) sets, basic and standby chan-

nels of basic and standby exchange adapter, basic and standby power sup-

ply, basic and standby electronics of the tracker, trigger, С4, ND, "I-DAQ"

system and also memory modules А and В;

в) testing electric interaction of the hardware with support systems of the

article: BCtS, CCIU, BTMS, CRPDS, HSRL OBE and also electric interac-

tion of communication lines with these systems.

To test communication lines between the hardware and support systems of

the article it is necessary to perform:

1. Two-way exchange of information (delivery of macro commands

(MCMD) to the hardware and receipt of service information from

the hardware) by line A and line B using the terminal – BCtS

communication test.

2. Issue of all necessary CC to the hardware under sequential dis-

connection of buses Еок1, Еок2 – CRPDS communication test.

3. Transmission of test information to HSRL OBE by the primary

and standby channel – HSRL communication test.

4. Issue of synchrosignals to the hardware by channel 1 and 2 -

CCIU communication test

353П-46КС-27895-1105 9

5. Assessment of TM for reference values – BTMS communication

test.

Functional scheme of communication between "Pamela" RH and GTS and

article’s systems is given in picture 1.

PSS

CRPDS BCtS CCIU

"Pamela" RH

HSRL OBE BTMS GTS

CMS

Figure 1 Functional scheme of communication between "Pam-

ela" RH and support systems of article 46КС and GTS.

353П-46КС-27895-1105 10

3.2 Tests support.

All kinds of testing of the hardware as part of article 46КС are carried out

using ground testing complex on the basis of the control computer and mathemati-

cal test support. Hardware control in the course of the test activations and joint op-

eration with HSRL OBE is carried out by nominal program A11 using RAM Pro-

gram. Hardware control in the course of IT is carried out by nominal program A11

initiated from OP.

Prior testing of "Pamela" RH as part of the article the following article’s

systems shall be activated and ready for operation: BVS, BDTS, BTCS, CRPDS,

PSS, CMS. HSRL OBE shall be activated and ready for operation prior the first

exchange session in the course of PAM TA with HSRL, JO and IT.

Pressurized container with "Pamela" RH shall be in transport condition

with the cover closed, "Pamela" RH normally joined with the article’s systems.

"Pamela" RH GSE shall be connected with "Pamela" RH through connector BCS

Х «ГН15Т.10» and connected with HSRL OBE GTE according to ИЭ17 part44. In

the course of all kinds of electrical testing of "Pamela" RH as part of the SC the

ground cooling system (353У.9152.001) is connected to "Pamela" RH cooling

loop hydraulic pipelines. Connection of the cooling loop and filling the working

fluid into the cooling loop are made according to Instructions 353У.9152.001 ПМ

2 and 353У.9152.001 ИЭ 2 during tests in “Progress” plant and in the launch site

accordingly. When the pressurized container is in operating position or in any in-

termediate position the tests shall not be carried out.

Power dump is allowed at any operational phase of "Pamela" RH. After

restoration of supply it is necessary to activate test program ЖР67 in input termi-

nal 10 to deactivate the hardware and to proceed with the nominal operation of

"Pamela" RH.

3.3 Evaluation of test results.

353П-46КС-27895-1105 11

Control of "Pamela" RH serviceability in the course of all electrical tests in

the article is executed by GTS using test programs ЖР67, ЖР68, ЖР69.

ЖР67 – program "Pamela" RH serviceability test in the course of TA with

support systems of the article";

ЖР68 – program "Control of "Pamela" RH/HSRL" JO;

ЖР69 – program "Test of "Pamela" RH serviceability in the course of IT".

To control serviceability of the hardware the following items are used by

GTS:

- nominal circuits of TM-control by channels of addressed TM selection;

- technological control circuits led to GTS through the signaling transmit-

ter (ST);

- Computer data (CD) transmitted from BCtS RAM through technologi-

cal channel "МТ".

Evaluation of tests results is carried out by ANP prints, tapes of open re-

cording of BTMS, testing scientific data.

3.4 GTE composition.

"Pamela" RH GSE (КБ7.101.00.000.00), GTE of HSRL OBE and ground

cooling system (353У.9152.001) are used in the course of testing of "Pamela" RH

as part of the article.

353П-46КС-27895-1105 12

4. TEST ACTIVATIONS OF "PAMELA" RH WITH

SUPPORT SYSTEMS OF THE ARTICLE

Test activations of "Pamela" RH with support systems are composed of

two parts: PAM TA and PAM TA with HSRL.

4.1 Procedure of PAM TA.

PAM TA are obtained using RAM Program 42 "Pamela" RH control in

TA" and test program ЖР67. The hardware control is performed by nominal pro-

gram А11.

RAM Program 42 is intended for:

- generation of ID for program А11 and the hardware,

- initiation of А11 program inputs at the necessary moments of time (ac-

cording to the time diagram),

- on-board and ground software synchronization,

- gaining CD by the test program through route mark (“RM”) channel,

- debugging test of MCMD "Lock the transmitter" and MCMD "Unlock

the transmitter" by the Terminal.

Prior PAM TA it is necessary to put BTMS in operational mode "ЗАП4",

ПрБ1.

PAM TA consist of the following fragments: "RH test, "Operation in tech-

nological regime", "GS test ".

It is possible to debug each fragment separately. The point of fragment de-

bugging is determined by availability of "1" in the position corresponded with

fragment’s number, GV "VPAMTA" (variant of «Pamela» RH test activations).

The distribution of positions GV "VPAMTA" is given below:

23 … 6 5 4 3 2 1 0

fr.4 fr.3 fr.2 fr.1

353П-46КС-27895-1105 13

This variable is specified from the planning program КП6 prior ЖР67 ini-

tiation by input 1 and is transmitted to RAM Program42 by switching on and off

the "ПИ КТП", "ПИСУД" indicators from program ЖР67.

If necessary "Pamela" RH operation on a special program is provided in-

cluding "Pamela" RH dismantling from the article and testing by means of "Pam-

ela" RH GSE.

353П-46КС-27895-1105 14

4.1.1 Procedure of PAM TA fragment 1 – "RH test".

Time diagram of this fragment is given in fig. 1.

The following activities are performed on this fragment:

test of hardware/CRPDS communication (transmission of all CC provided

for "Pamela" RH by buses Еок1 and Еок2),

test of "Pamela" RH/BTSC communication (operation under alternate dis-

connection of primary and standby synchrosignals issue channels),

debugging test of MCMD "Lock the transmitter" and MCMD "Unlock the

transmitter" by the Terminal.

For this purpose four "Pamela" RH activations are performed: the first one

and the third one - with bus Еок2 being disconnected, the second one and the

fourth one – with bus Еок1 being disconnected. For it under the second activation

the first BTCS synchrosignals channel is active, under the third one - the second

BTCS synchrosignals channel is active.

Connection and disconnection of buses Еок1 and Еок2 and also connec-

tion/disconnection of BTCS channels are performed by program ЖР67.

In case of disconnection of channel 1 BTCS, channel 2 BTCS, connection

of channels (after debugging of input 1, 2, 3 of program Б76 respectively) attribute

"ABN BTCS" is analyzed by program ЖР67. When this attribute=1 "PAM ABN"

GV (abnormal completion of "Pamela" RH test activations) of value =1 is formed

and drift to line 50 is performed.

Program ЖР67 is initiated by input 1 from the planning program before the

beginning of fragment 1 and RAM Program 42 is initiated right after OP loading.

First program ЖР67 verifies temperature TM-parameters of "Pamela" RH

for compliance with allowed values. If there is no "ABN" then program ЖР67

executes board timing. For it ЖР67 sets indicator "ПИ КТП" to 0 ("ПИ КТП" is

on) and for two minutes it controls "МТ1" signal generated by RAM Terminal42

with the state of "ПИ КТП" indicator being changed from “on” to “off” ("ПИ

353П-46КС-27895-1105 15

КТП" indicator status poll is performed by RAM Program42 with a period of

Т=1sec).

If "МТ1" signal is generated in due time ЖР67 program’s actions are as

follows:

-Within 3 seconds after synchronization ЖР67 changes "ПИ КТП" indica-

tor state by issuing CC "Off ПИ КТП" or CC "On ПИ КТП" and also issues CC

"On ПИ СУД" or "Off ПИ СУД" depending on the first position of GV "V PAM

TA" (for unit position of GV "V PAM TA" CC "Off ПИ СУД" is issued and for it

"ПИ СУД" indicator value=1).

- in 3 seconds after synchronization RAM Program42 performs control of

"ПИ КТП" indicator state and in case of its change it inserts "1" in position 1 of

its working cell "ВРАБ" if "ПИ СУД"=1 or – 0 if "ПИ СУД"=0;

- after that the rest three positions of "ВРАБ" variable are generated with

a period of 3 sec similarly to the above. So within 12 seconds from the

moment of synchronization the transmission of data on PAM TA frag-

ments processing on board is completed.

Then program ЖР67 executes the second RAM Program 42 timing with

zeroing the on-board time scale (ТБШВ) and time counters in the GTC and

BTMS. This is performed as follows:

-RAM program records the value=525258 in GV «КДБСК1.КОД» and

ТБШВ=0 in GV «ВЯ БСУ»;

- RAM program enters the setting of the time interval УВИД=tбшв +3sec.

for reference to the mark of seconds for activation of program A40 by input 1.

- during 3 seconds program ЖР67 controls the generation of "МТ" signal

(140478), formed by A40 program.

After that, program ЖР67 (If "МТ" signal from program A40 is generated

in due time) executes clearance of time meters at GTS and BTMS and proceeds

with its work according to the timing diagram.

353П-46КС-27895-1105 16

Upon completion of the fragment debugging program ЖР67 executes dis-

connection of "ПИ КТП" indicator.

In abnormal completion of PAM TA (no "МТ1", abnormal temperature pa-

rameters, a unit value of GV "N BTCS", etc) program ЖР67 forms GV "PAM

ABN"=1.

In the process of its operation in this fragment RAM Program 42 executes

connection of program А11 inputs to carry out:

- test of "Pamela" RH/BCtS communication channel (DTL А),

- issue of MCMD "Time synchronization", "Mode selection" with an at-

tribute of TRD purge inhibition, "Pamela" RH test”,

- debugging test of MCMD "Lock the transmitter" and MCMD "Unlock

the transmitter" by the Terminal,

- request of the status word of the hardware after it was subjected to some

activities.

RAM Program 42 also forms the following signals:

"МТ1" – in case of “on” condition of "ПИ КТП" indicator during timing;

"МТ2" – in case of no “on” condition of "ПИ КТП" indicator during tim-

ing;

"МТ3" – if "Pamela" RH status word with zero positions is available;

"МТ4" – if "Pamela" RH status word with nonzero positions is available or

no exchange via MCL.

Debugging of MCMD "Lock/unlock the receiver-transmitter" is performed

by the Terminal in the following order:

1) MCMD "Lock the transmitter" is issued to the hardware through DTL A

and this command causes DTL B receiver-transmitter to be locked;

2) After that RAM Program 42 sets DTL A fault sign to "1" (GV

"КДСПЛ2" [1]=1) and activates input 16 of program А11 where MCL

exchange being executed. The exchange is started by DTL B and is not

353П-46КС-27895-1105 17

executed (no OS) as DTL B receiver-transmitter is locked. Program

A11 forms coded CD А11-0=448 and =638;

3) Then after zeroing the anomaly flag of DTL1 A (КДСПЛ2[1]=0) RAM

Program 42 issues MCMD "Unlock the transmitter" to Pamela through

DTL A, zeroes GV "НРЛПИБ" (70411[2]=0), sets КДСПЛ2[1] into

“1” and activates input 16 of program А11 where DTL B exchange is

completed normally and program А11 forms coded CD А11-0=0;

4) After that RAM Program 42 through DTL B it issues MCMD "Lock the

transmitter" to Pamela and the command causes DTL A transmitter to

be locked;

5) Then RAM Program 42 sets DTL A fault attribute to "0" (GV

"КДСПЛ2" [1]=0) and activates input 16 of program А11 where MCL

exchange being executed again. As DTL A receiver-transmitter is

locked, the exchange is not executed (no OS), program А11 forms

coded CD А11-0=208 and goes to DTL B where the exchange is com-

pleted nominally;

6) Then RAM Program 42 issues MCMD "Unlock the transmitter" by

DTL B;

7) After that RAM Program 42 zeroes DTL A exchange impossibility at-

tribute for program А11 (GV "НРЛПИА" (70412[9]=0) and activates

program А11 by entry 16. DTL A exchange is executed nominally

(coded CD А11-0=0).

Controlling the status word (StW) RAM Program 42 executes the follow-

ing: it issues MCMD “OFF GS” if "УНН" parameter (positions 1-4) =1 or 2, if the

value =1 for positions 11, 12, 13 it activates program А11 by input 13 for emer-

gency deactivation of "Pamela" RH.

In fragment 1 RAM Program 42 forms the following ID for program А11

and the hardware:

353П-46КС-27895-1105 18

- MCMD "Mode selection";

- MCMD "RH test".

MCMD data is given in table 2.

All commands sent to the hardware in the first fragment of PAM TA are

given in table 1.

Table 1

Command type Command name The command issue time The com-

mand issue

place

The first activation (in Еок1 and first BTCS channel)

СС Pamela power bus

on

t0 – time of on-board and

testing program synchro-

nization

ЖР67

СС "PSCU ON MAIN" 230 s +t0 ЖР67

MCMD СС request 350 s +t0 А11

CC "GAS ENABLE" 352 s +t0 ЖР67

"Interaction test of RH with BCtS via MCL"

MCMD Issue 32 words of

test info

355 s +t0 А11

MCMD read 32 words of

test info

А11

MCMD "Transmit StW" А11

MCMD StW request 357 s +t0 А11

MCMD Time Sync 365 s +t0 А11


MCMD "Select Mode" 375 s +t0 А11

1 data transmission line

353П-46КС-27895-1105 19


mand issue

place


CC "IPM1 ON" 385 s +t0 ЖР67

CC "IPM3 ON" 385 s 200 ms +t0 ЖР67

CC "IPM5 ON" 385 s 400 ms +t0 ЖР67



CC ND power bus on 10 min +t0 ЖР67

CC "ND ON" 11 min +t0 ЖР67

CC ND main low volt-

age

12 min +t0 ЖР67

CC ND main high volt-

age

13 min +t0 ЖР67

Nominal deactivation

MCMD "Select Mode" 14 min +t0 А11

MCMD СС request 14 min 1s +t0 А11

MCMD " Select Mode " 14 min 2s +t0 А11



CC "IPM 1,2 OFF" 14 min 4s +t0 А11

CC "IPM 3,4 OFF " А11

CC "IPM 5,6 OFF " А11

CC "PSCU OFF" А11

CC "ND OFF" А11

CC "GAS OFF" А11

CC "Waiting Mode On" А11

353П-46КС-27895-1105 20


mand issue

place

CC ND power bus off А11

CC Pamela power bus

off

А11

The second activation (in Еок2 and first BTCS channel)

CC Pamela power bus

on



nization

ЖР67

CC "PSCU ON MAIN" 230 s +t0 ЖР67


СС "GAS ENABLE" 352 s +t0 ЖР67

"Interaction test of RH and BCtS via MCL"

MCMD issue 32 words of

tests info

355 s +t0 А11


test info

А11








CC "IPM3 ON" 385 s 200 ms +t0 ЖР67

CC "IPM5 ON" 385 s 400 ms +t0 ЖР67

353П-46КС-27895-1105 21


mand issue

place





CC ND main low volt-

age

12 min +t0 ЖР67

CC ND main high volt-

age

13 min +t0 ЖР67

Nominal deactivation (see above)

The third activation of the hardware (in Еок1 and second BTCS channel)

CC Pamela power bus

on



nization

ЖР67

CC "PSCU ON

SPARE"

230 s +t0 ЖР67



"Interaction test of RH and BCtS via MCL"


test info

355 s +t0 А11

MCMD read 32 words test

info

А11




353П-46КС-27895-1105 22


mand issue

place





CC "IPM4 ON" 385 s 200 ms +t0 ЖР67

CC "IPM6 ON" 385 s 400 ms +t0 ЖР67





CC ND spare low volt-

age

12 min +t0 ЖР67

CC ND spare high volt-

age

13 min +t0 ЖР67


The fourth activation (in bus Еок2)

CC Pamela power bus

on



nization

ЖР67

CC "PSCU ON

SPARE"

230 s +t0 ЖР67



353П-46КС-27895-1105 23


mand issue

place

"Interaction test of RH with BCtS via MCL"


test info

355 s +t0 А11


test info

А11







CC "IPM 2 ON" 385 s +t0 ЖР67

CC " IPM 4 ON " 385 s 200 ms +t0 ЖР67

CC " IPM 6 ON " 385 s 400 ms +t0 ЖР67




CC "ND OFF" 11 min +t0 ЖР67

CC ND spare low volt-

age

12 min +t0 ЖР67

CC ND spare high volt-

age

13 min +t0 ЖР67

MCMD "RH test" 14 minutes +t0 А11


CC "RESET PSCU" 15 min +t0 ЖР67

353П-46КС-27895-1105 24


mand issue

place

CC "SAFE MODE

ON"

16 min +t0 ЖР67

CC "SAFE MODE

OFF"

17 min +t0 ЖР67

CC "Waiting Mode

Off"

18 min +t0 ЖР67

CC " Waiting Mode On

"

18 min 20s +t0 ЖР67

Еок1 ON, Еок2 OFF

CC "RESET PSCU" 20 min +t0 ЖР67

CC "SAFE MODE

ON"

21 min +t0 ЖР67

CC "SAFE MODE

OFF"

22 min +t0 ЖР67

CC "Waiting Mode

Off"

23 min +t0 ЖР67

CC " Waiting Mode On

"

23 min 20s +t0 ЖР67

Test of the terminal debugging of MCMD "Lock the transmitter",

"Unlock the transmitter".

MCMD "Lock the

transmitter" (on

DTL B)

25 min +t0 ПрОЗУ42

"Test of RH/BCtS interaction through MCL"

353П-46КС-27895-1105 25


mand issue

place

MCMD "Unlock the

transmitter" (on

DTL B)



MCMD "Lock the

transmitter"

(on DTL A)



MCMD "Unlock the trans-

mitter " (on DTL

A)




MCMD "Select Mode" 35 min +t0 А11


MCMD "Select Mode" 35 min 2s +t0 А11



СС "IPM1-2 Off" 35 min 4с +t0 А11

СС "IPM3-4 Off" А11

СС "IPM5-6 Off" А11

СС PSCU Off А11

СС ND Off А11

СС GAS Off А11

353П-46КС-27895-1105 26


mand issue

place

СС GS standby mode

on

А11

СС ND power bus off

А11

СС Pamela’s power bus off

А11

353П-46КС-27895-1105 27

Table 2 MCMD, formed by RAM Program 42 for fragment 1 of PAM TA.

MCMD "Select Mode"

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

counter MCMD = 0

0 code MCMD = 3316

length MCMD = ?

Time indicator (most significant bit) = 0

Time indicator (least significant bit) = 0

0 CW = 0

MCMD " Pamela’s test "

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

Counter MCMD = 0

0 Code MCMD = 8F16

Length MCMD = 7



0 CW = 0

For this fragment "Pamela" RH is activated by CC "ON MAIN PSCU")

from program ПР67, nominal purging of TRD is not executed.

"Select Mode"

MCMD data field

"RH" test” MCMD data field

353П-46КС-27895-1105 28

4.1.2 Procedure of PAM TA fragment 2 – "Technological operation".

For this fragment the hardware is activated nominally, the 2, 3 and 6-rd

protection unit, memory module А, standby sources of low and high ND voltage

are ON. A2 operational mode is debugged. The following MCMD are debugged by

the hardware: "PCSU S/W correction", "Memory unload", "History zone reboot".

The time diagram is given in figure 9. Time sync of ground and on-board software

operation is made in the same way as in item 4.1.1.

In this fragment CD2 shall be taken off with micro OP№*** being pre-

recorded for reading the data array off WM BCtS 510008 address of size 2048 16-

digit words.

RAM Program42 forms the following ID necessary for А11 program and

the hardware in this fragment:

- GV "ЗВРПК"=1;

- GV "БЛПГК"=0;

- GV "БЛПАМ"=0;

- GV "ВРБУЗП"=1;

- GV "КДБЗ"=468;

- GV "НРНД"=0;

- GV "ВРНИЗН"=1;

- GV "ВРВЫСН"=1;

- GV "ВРИСПП"=0;

- GV "СЧПРПО"=0;

- GV "КДМАСК"=0;

- 2 MCMD "DUMP";

- MCMD "PATCH";

- MCMD "Select Mode";

- MCMD " History zone reboot ".

These MCMD are given in fig. 3.

Table 3 ID, formed by RAM Program42 for fragment 2 of PAM TA.

353П-46КС-27895-1105 29

MCMD "Select Mode" 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

Counter MCMD=0

0 Code MCMD=3316

Length MCMD=?



0 CW

MCMD "DUMP" 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

Counter MCMD=0

0 Code MCMD = 2116

Length MCMD =9



CW

MCMD "PATCH" 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

Counter MCMD =0

0 Code MCMD = 2016

353П-46КС-27895-1105 30

Length MCMD = ?



КС

MCMD " History zone reboot " 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

Counter MCMD =0

0 Code КДМК = 2216

Length MCMD = 6



КС

Commands sent to the hardware in the second fragment of PAM TA are

given in table 4.

Table 4


mand is-

sue place

"Nominal activation"

CC Pamela’s power bus on

t0 – time of on-board and test-

ing program synchronization

А11

353П-46КС-27895-1105 31


mand is-

sue place

CC "PSCU ON

SPARE"

230 s + t0 А11

MCMD СС request 350 s + t0 А11

MCMD "RH/BCtS inter-

action test via

MCL" (see Ta-

ble 1)

351 s + t0

MCMD Time Sync 352 s + t0


CC "IPM 2 ON" 354 s + t0 А11

CC "IPM 3 ON" 354 s 250 мс + t0 А11

CC "IPM 6 ON" 354 s 500 мс + t0 А11

CC "GAS EN-

ABLE"

А11



MCMD "Select Mode" 508 s + t0 А11


CC ND power bus on

А11

CC "ND ON" А11

CC ND spare low

voltage

А11

CC ND spare high

voltage

А11

353П-46КС-27895-1105 32


mand is-

sue place

MCMD "Select Mode" 9 min + t0 А11

MCMD "DUMP" 10 min + t0 А11

MCMD Reset memory

dump into

RAM BCtS

12 min + t0 А11

MCMD "PATCH" 15 min + t0 А11

MCMD "DUMP" 18 min + t0 А11

MCMD Reset memory

dump into

RAM BCtS

19 min + t0 А11

MCMD Reset history

zone MCMD

into RAM BCtS

22 min + t0 А11

MCMD "RESET HIS-

TORYAREA"

23 min + t0 А11

MCMD Reset history

zone MCMD

into RAM BCtS

25 min + t0 А11

"Nominal OFF"

(see Table 1)

40 min + t0 А11

353П-46КС-27895-1105 33

4.1.3 Procedure of PAM TA fragments 3, 4 – "GS test".

The time diagram of the fragments is given in figures 9,10. Time sync of

ground and on-board software operation is made in the same way as in item 4.1.1.

Fragment 3 is executed both for technological and flight "Pamela" RH pro-

totype.

In this fragment GS is tested for what concerns TRD purging, release of

differential pressure from PC. Fragment 4 is executed with a flight prototype only.

A general nominal purging of TRD is carried out. The duration of this fragment is

about 7 hours. During these hours "Pamela" RH status is under control of nominal

program А11 input 11 (request of the hardware for a status word with 10 sec pe-

riod) and test program ЖР67 input 3 (schematic TM).

For debugging of fragments 3, 4 RAM Program 42 forms the following ID:





- GV "КДБЗ"=158;

- GV "НРНД"=0;






- MCMD "TRD purging";

- MCMD "Mode selection";

- MCMD "PC pressure release".

These MCMD are given in table 5.

Table 5 ID, formed by RAM Program 42 for fragments 3, 4 of PAM TA.

353П-46КС-27895-1105 34

MCMD "TRD purging" 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

Counter MCMD=0

0 MCMD= 3016

Length MCMD =7

Time indicator (most significant) = 0

Time indicator (least significant) = 0

CW

MCMD "PC pressure release" 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

Counter MCMD =0

0 MCMD = 3116

Length MCMD =7



CW

MCMD "Select Mode" 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

Counter MCMD =0

0 MCMD = 3316

Length MCMD =?



MCMD data area “Select Mode”

353П-46КС-27895-1105 35

CW

Commands sent to the hardware in the third fragment of PAM TA are

given in table 6.

Table 6


mand is-

sue place





А11

CC "PSCU ON

MAIN"

230 s + t0 А11



action test via

MCL" (see table

1)

351 s + t0


MCMD СС request 353s + t0 А11

CC "IPM 1 ON" 354 s + t0 А11

CC "IPM 3 ON" 354 s 250 мs + t0 А11

CC "IPM 5 ON" 354 s 500 мs + t0 А11

CC "GAS ENABLE" А11


353П-46КС-27895-1105 36


mand is-

sue place




CC ND power bus on

А11

CC "ND ON" А11

CC ND main low

voltage

А11

CC ND main high

voltage

А11

MCMD PURGE TRD 540 s + t0 А11


MCMD START CON-

TAINER PURG-

ING

724 s (7 h 662s)*+ t0 А11

"Nominal OFF"

(see table 1)

985 s (7 h 1083s )* + t0 А11

* Values in parentheses are given for fragment 4.

353П-46КС-27895-1105 37

Figure 1 Time diagram of PAM TA fragment 1 (beginning)

ЖР67 in.1

УВИД1=350s+tTSD

КП6 CC "Откл.

Еок2"

ПрОЗУ42

t0=tCTS=0

МТ

t0+230s

PSC

U O

N M

AIN

(PSC

U O

N S

PAR

E)

УВИД2=355s+ tTSD А11 inp.16

(MCL tets)

GA

S EN

AB

LE

ПШПП

А36 initiation in input 26

УВИД3=357s+tTSD А11 in.p15

(СС)

МТ3

А11 inp.15

(СС)

МТ3

А11 inp. 6

(MCMD

"Synchr")

А11 inp. 6

(MCMD"Select Mode")

УВИД4=365s+tTSD

IPM

1 (2

) ON

IPM

3(4)

ON

IPM

5(6)

ON

t0+385s

УВИД6=375s+tTSD

А11 inp.15

(СС)

МТ3

УВИД5=367s+tTSD УВИД8=387s+tTSD

А11 inp.15

(СС)

МТ3

УВИД7=377s+tTSD

TRD purging inhibit in-

dicator is introduced

А11 inp. 15

(СС)

УВИД9=537s+tTSD

А11 in.p15

(СС)

МТ3

УВИД8=387s+tTSD

МТ3

t0+352s

МТ1

OP

CC

"O

N Еок

1"

CC

"O

FF Еок

2"

1-st "Pamela" RH activation

Б76 input1

УВИД10=14min+tо

А11 inp.2

deactivation

2s 2s

2s 2c

2s 2s

A40 in.1 УВИД=3s+tTSD

t0+10min… t0+14min

CC

" N

D p

ower

bus"

, "N

D O

n"

353П-46КС-27895-1105 38

Figure 2 Time diagram of PAM TA fragment 1 (continued)

УВИД10=14мин+tо

А11 inp.2

deactivation 2-nd activation of "Pamela" RH

БР76 input3 БР76 input 2

3-rd activation of "Pamela" RH

Бр76 input 3

УВИД10=14min+tо

А11 input 2

deactivation 4-th activation of "Pamela" RH

CC

"O

FF Еок

2"

CC

"O

N Еок

1"

t0+15min 60 sec 60 sec

60 sec

CC

"O

N Еок

2"

t0+15min

CC

"O

FF Еок

1"

t0+16min

t0+16min t0+18min t0+19min

t0+18min

353П-46КС-27895-1105 39

Figure 3 Time diagram of PAM TA fragment 1 (continued)

t0+23min t0+23 min 20s

УВИД13=25 минут +tTSD


CC

"R

ESET

PSC

U"

CC

"SA

FE M

OD

E O

N"

CC

"SA

FE M

OD

E O

FF"

УВИД14=27 min +tTSD УВИД15=29min+tTSD

А11 in.16

MCL Test

А11 in.16

MCL test

MC "Lock trans-

mitter"

MC "Unlock transmit-

ter"

Test of MCMD "Lock the transmitter", "Unlock the transmitter"

by bus А


CC

"R

ESET

PSC

U"

CC

"SA

FEM

OD

EO

N"

CC

"SA

FE M

OD

E O

FF"

t0+18min t0+18 min 20s

CC

"W

aitin

g m

ode

OFF

"

CC

"W

aitin

g m

ode

ON

"

КУ

"Вкл

. Еок

2"

КУ

"Откл.

Еок

1"

CC

"SA

FE M

OD

E O

N"

CC

"SA

FE M

OD

E O

FF"

CC

" Еок

2 O

N"

CC

"Еок1

OFF

"

353П-46КС-27895-1105 40

Figure 4 Time diagram of PAM TA fragment 1 (ending)

А11 in. 2

(OFF.)

УВИД16=31 min +tTSD УВИД17=35 min +tTSD

А11 in.16

MCL test А11 in. 16

MCL test

MC "Lock transmittre"

MC "Unlock transmit-

ter"

Test of MCMD "Locking", "Unlocking" in bus А

353П-46КС-27895-1105 41

Figure 5. Time diagram of PAM/HSRL TA fragment 1 (beginning).

УВИД4,i=760s+tTSD

i=1-200

t0=tcts=0

ЖР67 inp.5

А11 inp. 9

MCMD Orbital

information

ПрОЗУ 43

МТ

А11 inp.1

RH in mode.

В4


А11 inp.7

MCMD Inclina-

tion information

А11 inp.6

MCMD Time

Sync

А11 inp.15

ССА request

УВИД5=1360s+tTSD

МТ3


А11 inp.6

MCMD 1 main trig ON and

1 trig. ВЭ

УВИ7=2000s+tTSD

А11 inp.6


2 trig. ВЭ

УВИ8=2600s+tTSD

А11 inp.6

MCMD 1 spare trig ON and

3 trig. ВЭ

УВИ9=3200s+tTSD

А11 inp.6

MCMD 2 spare trig ON

УВИ10=3800s+tTSD

А11 inp.6

MCMD 1 trig RH ON OBE

УВИ11=4400s+tTSD

УВИД1=3s+tCTS

A40 inp.1

353П-46КС-27895-1105 42

Figure 5. Time diagram of PAM/HSRL TA fragment 1 (continued).

А11 inp.6

MCMD 1 main trig ON, 2 trig. UHE

And all 2 level triggers OFF

УВИ18=8400s+tTSD

А11 inp.6

MCMD "Trigger" ON 2 level

УВИ15=6800s+tTSD

А11 inp.6

MCMD 2 level " АС PROHIBITION"

ON

УВИ16=7200s+tTSD

А11 inp.6

MCMD 2 level "TOF" ON

УВИ17=7800s+tTSD

А11 inp.6

MCMD 2 trig. OBE ON

УВИ12=5000s+tTSD

А11 inp.6

MCMD 3 trig. OBE ON

УВИ13=5600s+tTSD

А11 inp.6

MCMD 1 main trig and trig

"Spectrometer" 2 level trig ON

УВИ14=6200s+tTSD

УВИ19=8500s+tTSD

ПрОЗУ13 inp.1

УВИ20=8800s+tTSD

А11 inp. 10

Тнм1= 8900s+ tCTS 1 session of exchange with HSRL OBE

УВИ21=9100s+tTSD

353П-46КС-27895-1105 43

Figure 5. Time diagram of PAM/HSRL TA fragment 1 (continued).

А11 inp. 2 (off)


А11 inp.6


MCMD "select

mode"

А11 inp.15

Request area ССА

УВИД24=9300с+tTSD

t0=tcts+9260s

А11 inp.1

RH in mode

В4

УВИД25=9900s+tTSD А11 inp.6

MCMD to initiate

standby electronics

А11 inp.6


1 trig. UHE

УВИ27=10600s+tTSD

А11 inp.6


2 trig. UHE


А11 inp.6

MCMD 1 spare trig ON and 3 trig. UHE


А11 inp.6

MCMD 2 spare trig ON


А11 inp.6

MCMD 1 trig OBE ON



353П-46КС-27895-1105 44

А11 inp 6

MCMD 1 main trig ON, 2 trig. UHE

And all triggers 2 level OFF


А11 inp.6

MCMD "Trigger" trig 2 level ON


А11 inp.6

MCMD trigger 2 level ON "АС PRO-

HIBITION"


А11 inp.6

MCMD trigger 2 level ON "TOF"


А11 inp.6

MCMD 2 trig OBE ON


А11 inp.6

MCMD 3 trig OBE ON


А11 in.p6


"Spectrometer" trig 2 level ON


А11 inp. 2 (off)

17740s+tTSD

Тнм2=17400s+ tTSD

2 session of exchange

with HSRL OBE

Figure 5 Time diagram of PAM/HSRL TA fragment 1 (ending).

353П-46КС-27895-1105 45

4.2 Procedure of PAM/HSRL TA.

Before PAM/HSRL TA start ЖР 67 program is activated by input 5 from

the planning program. RAM program 43 is activated immediately after loading the

operational program. Nominal A11 program controls Pamela.

Prior debugging this fragment it is necessary to re-activate HSRL without

warming-up and to initiate BDTS to mode "ЗАП8", ПрБ1. HSRL initiation is re-

corded by tapes of open TM recording.

PAM/HSRL TA consist of 2 fragments: “Nominal operation, checkout of

spare electronics” and “Checkout of connection with HSRL” .

It is possible to debug each fragment separately. The point of fragment de-

bugging is determined by availability of "1" in the position corresponded with

fragment’s number, GV "VPAMTA" (variant of «Pamela» RH test activa-

tions).The distribution of bits of this variable, its assignment and uplinking of in-

formation on the performance of PAM/HSRL TA fragments is analogous to the

described under 4.1 and 4.1.1.

4.2.1 Procedure of PAM/HSRL TA fragment 1 – "Nominal operation,

standby electronics test".

The diagram of debugging this fragment by the hardware is given in Fig 4.

Time sync of ground and on-board software operation is made in the same

way as in item 4.1.1.

"Pamela" RH GSE/HSRL GTE connection diagram is given in Fig 7.

For debugging this fragment of PAM TA it is necessary to connect per-

sonal computer (PC) of "Pamela" RH GSE and HSRL GTE and also to initiate

RAM Program 13 input 1 developed by department 1107 from RAM Program 43

to initiate HSRL OBE in due time (not less than 100 sec prior the first Тнм1-

exchange session). GSE is to be connected to "Pamela" RH (through connector of

BCS Х «ГН15Т.10»).

For this testing fragment "Pamela" RH is activated twice. The first activa-

tion of the hardware is executed by initiation of nominal program А11 in input 1

353П-46КС-27895-1105 46

from RAM Program 43. The 1, 4, 6-th protection units (PU), memory module А,

primary sources of low and high ND voltage are initiated. After nominal activation

the hardware is in В4 mode of operation.

After that by consequent initiations of program A11 in inputs 9, 6 RAM

Program 43 provides for issue of MCMD: "Orbit information (CMMP)", "Time

synchronization".

Then RAM Program 43 provides for transmission of AP arrays to the

hardware within 10 minutes with 3 sec period by repeated initiations of program

A11 in input 6 for simulation of similar conditions in the course of nominal opera-

tion of "Pamela" RH.

After that RAM Program 43 performs ССА zone query (by initiating pro-

gram А11 in input 15), rewrite of 12 ССА zone words to BCtS RAM and "МТ3"

signal transmission to GTS RAM via "МТ" channel in case all CCА zone parame-

ters are normal.

Then RAM Program 43 performs testing of trigger system of the first and

second level in the following way:

- MCMD are issued for activation of the first main trigger and the first

trigger for high-energy electrons (by initiating program А11 in input 6);

- in 10 minutes MCMD are issued to the hardware for activation of the

second main trigger and the second trigger for high-energy electrons;

- in 10 more minutes MCMD are issued for activation of the first standby

trigger and the third trigger of high-energy electrons;

- with a period of 10 minutes MCMD are issued for activation of the sec-

ond standby trigger, the first trigger for Brazilian anomaly, the second

trigger for Brazilian anomaly and the third trigger for Brazilian anom-

aly;

- in 10 more minutes MCMD are issued for activation of the first main

trigger and second level trigger "Spectrometer" of the trigger system;

353П-46КС-27895-1105 47

- in 10 minutes MCMD is issued for activation of second level trigger

"trigger";


"АС inhibition";


"TOF";

- in 10 more minutes MCMD are issued for activation of the first trigger

by default, the first trigger of high-energy electrons and for deactivation

of all second level triggers.

After that RAM Program 43 provides for HSRL exchange session for

transmission of the accumulated scientific data via HSRL OBE and HSRL GTE

relay to "Pamela" RH GSE for processing and making a conclusion. This exchange

session is carried out using the main exchange adapter in the main data transmis-

sion channel.

Then RAM Program 43 including program А11 in input 6 provides for is-

sue of MCMD "Mode selection" to the hardware, ССА zone query for transmis-

sion to GTS RAM and the following (in 20 sec) "Pamela" RH deactivation (by ini-

tiating program А11 in input 2).

After that the second hardware activation is executed in this fragment. It is

also executed by initiation of nominal program А11 in input 1 from RAM Program

43. After nominal activation the hardware is in В4 mode of operation.

Then RAM Program 43 provides for issue of MCMD for connection of

standby electronics of the tracker, trigger, С4 and system "I-DAQ".

After that the first and second level triggers are tested the way it’s specified

above.

After that RAM Program 43 provides for HSRL exchange session for

transmission of the accumulated scientific data via HSRL OBE and HSRL GTE

relay to "Pamela" RH GSE for processing and concluding.

353П-46КС-27895-1105 48

Then nominal "Pamela" RH deactivation is executed by initiating program

А11 in input 2.

For debugging PAM/HSRL TA fragment 1 RAM Program 43 forms the

following ID:










- GV "КДБЗ"=518 (for the first activation) and GV "КДБЗ"=268 (for the

second activation);

- GV "НРНД"=0;

- GV "ВРАДАП"=0;

- GV "ВРКАН"=0 for the 1-st exchange session, =1 for the second ex-

change session.

- MCMD "Orbit information (CMMP)";

- MCMD "Inclination data (AP)";

- MCMD "Time synchronization";

- MCMD "Mode selection".

These MCMD are given in table 7.

MCMD for activation/deactivation of triggers and initiation of standby

electronics of the tracker, trigger, С4 and system "I-DAQ" will be given below.

353П-46КС-27895-1105 49

Table 7 MCMD formed by RAM Program 43 for PAM/HSRL TA frag-

ment 2.

MCMD Orbital information

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

Counter MCMD = 0

0 Code MCMD = Е116

Length MCMD = 20



1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0

1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0

1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

0 CW

MCMD Inclination information

CM

MP

arra

y

353П-46КС-27895-1105 50

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

Counter MCMD = 0

0 Code MCMD = Е216

Length MCMD = 66



1 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0

0 1 1 0 0 0 0 1 1 1 0 0 0 0 0 0

0 1 1 1 0 0 1 1 1 0 0 0 0 0 0 0

0 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0

0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 0

0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 0

0 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0

0 0 1 1 0 0 1 1 1 0 0 0 0 0 0 0

1 1 1 0 0 0 0 1 1 1 0 0 0 0 0 0

1 1 0 0 0 0 0 0 1 1 1 0 0 0 0 0

ППО-2 = ППО-1

ППО-3 = ППО-1

ППО-4 = ППО-1

ППО-5 = ППО-1

ППО-6 = ППО-1

0 CW

MCMD Time Sync

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

Counter MCMD =0

0 Code MCMD = Е016

AP-

1 ar

ray

353П-46КС-27895-1105 51

Length MCMD = 8



ТBTS

ТBTS

CW

MCMD Select Mode

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

Counter MCMD =0

0 Code MCMD = 3316

Length MCMD = ?



CW

All controls issued to the hardware in the first fragment of PAM/HSRL TA

are given in table 4.

353П-46КС-27895-1105 52

Table 8

Control type Control name The control issue time The con-

trol issue

point


CC Pamela 's power bus on



А11

CC "PSCU ON

MAINE"

230 s + t0 А11



action test via

MCL" (see Ta-

ble. 1)

351 s + t0



CC "IPM 1 ON" 354 s + t0 А11

CC "IPM 4 ON" 354 s 250 мs + t0 А11

CC "IPM 6 ON" 354 s 500 мs + t0 А11

CC "GAS EN-

ABLE"

А11





353П-46КС-27895-1105 53


trol issue

point

CC ND power bus on

А11

CC "ND ON" А11

CC ND main low

voltage

А11

CC ND main high

voltage

А11

MCMD Orbital informa-

tion

600 sec + t0 А11

MCMD Time sync 660 sec + t0 А11

MCMD Inclination in-

formation

760 s + t0 and on with the pe-

riod of 3 sec during 10 min

А11

MCMD ССA request 1360 sec + t0 А11

MCMD activation 1

main trig and 1

trig. ВЭ

1400 sec + t0 А11

MCMD Activation 2

main trig and 2

trig ВЭ

2000 sec + t0 А11

MCMD Activation 1

spare trig and 3

trig ВЭ

2600 sec + t0 А11

MCMD Activation 2

spare trig

3200 sec + t0 А11

MCMD 1 trig OBE ON 3800 sec + t0 А11

353П-46КС-27895-1105 54


trol issue

point



MCMD 1main trig ON

and 2 level trig

"Spectrometer"

5600 sec + t0 А11

MCMD 2 level trig ON

"Trigger"

6200 sec + t0 А11


"АС Prohibit"

6800 sec + t0 А11


"TOF"

7800 sec + t0 А11

MCMD 1 main trig ac-

tivation, 2 trig

ВЭ ON and all

triggers of 2

level ON

8400 sec + t0 А11

First communication session

MCMD Time sync 8880 sec + t0 А11

MCMD Select Mode А11

MCMD "DOWNLOAD" А11

MCMD ССA request А11


MCMD Select Mode 9110 sec + t0 А11


353П-46КС-27895-1105 55


trol issue

point

Nominal OFF

(see Table 1)

9220 sec + t0 А11

Nominal switch ON (second)




А11

CC "PSCU ON

SPARE"

230 s + t0 А11



action test via

MCL" (see Ta-

ble 1)

351 s + t0

MCMD Time sync 352 s + t0


CC "IPM 2 ON" 354 s + t0 А11

CC "IPM 3 ON" 354 s 250 мs + t0 А11

CC "IPM 4 ON" 354 s 500 мs + t0 А11

CC "GAS EN-

ABLE"

А11





353П-46КС-27895-1105 56


trol issue

point

CC ND power bus on

А11

CC "ND ON" А11

CC ND spare low

voltage

А11

CC ND spare high

voltage

А11

MCMD Spare electron-

ics ON

9900 s + t0 А11

MCMD 1 main trig and

1 trig ВЭ ON

10000 s+ t0 А11


2 trig ВЭ ON

10600 s + t0 А11

MCMD 1 spare trig and

3 trig ВЭ ON

11200 s + t0 А11

MCMD 2 spare trig and

spare trig ON

11800 s + t0 А11

MCMD 1 trig OBE ON 12400 s+ t0 А11

MCMD 2 trig OBE ON 13000 s + t0 А11

MCMD 3 trig OBE ON 13600 s + t0 А11


2 level trig

"Spectrometer "

ON

14200 s + t0 А11

353П-46КС-27895-1105 57


trol issue

point

MCMD 2 level trig

"Trigger" ON

14800 s + t0 А11

MCMD 2 level trig

"АС Prohibi-

tion" ON

15400 s + t0 А11

MCMD 2 level trig

"TOF " ON

16000 s + t0 А11

MCMD 1 main trig , 2

trig ВЭ ON and

all 2 level trig-

gers OFF

16600 s + t0 А11

MCMD

MCMD " Time Sync 17380 s + t0 А11

MCMD Select mode " А11



MCMD ССA request 17603 s + t0 А11

Nominal switch

OFF (see Table

1)

17700 s + t0 А11

353П-46КС-27895-1105 58

МП2 array formed by RAM Program 43 to provide for two exchange ses-

sions is given in Fig 6.

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1

ТНОИ=0 2

КРСР КСН

ПМХСМ

НА

3

НА

2

НА

1 КМАР=2 3

НВ=1 4 ТНСН1 5

//////////////////////// ДЛСН1 6 ТНСН2 7

//////////////////////// ДЛСН2 8 ТНСН3 9

//////////////////////// ДЛСН3 10 ///////////////////////////////////// ПКАС ПД /////////// 11

КПЗВ КПЗН 12

//////////////////

ПРБ

А13

ПРБ

А23

СП3

ПРБ

А12

ПРБ

А22

СП2

ПРБ

А11

ПРБ

А21

СП1 ///// 13

//////////////////////////////////////////////////////////////// НЧК3 НЧК2 НЧК1 14 ПХМ1

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 00 /////////////////////////////// КМАРР=1 КРНА=1110 1

ДЛМ =200с 2 ТНМ=8900 sec 3

СДИ* 4 /////////////////////////////////////////////////////////////////////////////////////////////////////// 5

ДЛС 6 ДЛЗНП (ДЛАП2) 7

СПК2 НПК2 (НМП2) СПК1 НПК1 (НМП1) 8 СПК4 НПК4 (НМП4) СПК3 НПК3 (НМП3) 9

////////////////////////////////////////////

ПВКЗУ

ПС /////////// НМВ=1 10

00000 00 0 0 0000000 11

353П-46КС-27895-1105 59

0 0000000 0 0000000 12 С К МЭ Т1 Т2 Т3 /////////// РФСЧ ///////////////////////////////////// 13 КСНР1 КСНВ1 КСНН1 ///// НРЗ1 14 КСНР2 КСНВ2 КСНН2 ///// НРЗ2 15 КСНР3 КСНВ3 КСНН3 ///// НР33 16 КС1 КС2 КС3 /////////////////////////////// РВО 17

ПХМ2 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

00 /////////////////////////////// КМАРР=1 КРНА=1110 1 ДЛМ =200с 2

ТНМ=17400 sec 3 СДИ* 4

/////////////////////////////////////////////////////////////////////////////////////////////////////// 5 ДЛС 6

ДЛЗНП (ДЛАП2) 7 СПК2 НПК2 (НМП2) СПК1 НПК1 (НМП1) 8 СПК4 НПК4 (НМП4) СПК3 НПК3 (НМП3) 9

////////////////////////////////////////////

ПВКЗУ

ПС /////////// НМВ=2 10

00000 00 0 0 0000000 11


МХСМ

Figure 6

353П-46КС-27895-1105 60

4.2.1.1 Order of gaining information from HSRL GTE.

1) HSRL GTE records (to flight time diagram) information obtained

from technological output of HSRL OBE during PAM/HSRL TA

or from nominal output of HSRL OBE during JO and IT;

2) Information of each recorded route is conversed into a file;

3) After completing PAM TA fragment HSRL GTE converses in-

formation into the original form – information packets at HSRL

OBE input;

4) When the information is conversed HSRL GTE by request of

"Pamela" RH GSE issues information via ЛВС "FAST

EHERNET" at a rate of 100 Мbaud (real transmission rate – 2-5

MB/s). "Pamela" RH GSE request consists in the following:

"Pamela" RH operator opens "Pamela" directory (with conse-

quent opening of all embedded directories) in PC being part of

HSRL GTE and transfers necessary files to PC being part of

"Pamela" RH GSE.

The structure of the information in directory "Pamela" of HSRL GTE PC is

as follows:

- The directory with a number and date of the fragment –

"ФХУ_АБ_ВГ_ДЕ_ЖЗ", where: Ф - fragment,

Х – number of the fragment,

У – sequence number for the fragment

iteration,

АБ – month.

ВГ – date,

ДЕ – hours,

ЖЗ – minutes;

- "MN" directory with the number of the route in this PAM TA fragment,

353П-46КС-27895-1105 61

where М – route, N - № of the route in this fragment,

- "SFI.pam" data file containing packets with scientific information of

"Pamela" RH.

353П-46КС-27895-1105 62

4.2.2 Procedure of PAM/HSRL TA fragment 2 – "Test of HSRL com-munication channels". The time diagram of this fragment is given in Figure 7.



"Pamela" RH GSE/HSRL GTE connection diagram is given in Fig 6.

In this fragment RAM Program 43 provides the following activities:

- timely (not less than 100 sec before the beginning of the first Тнм1-

exchange session) initiation of RAM Program 13 input 1 for activation

of HSRL OBE,

- the hardware change over to operational mode А0 (by initiating program

А11 in input 6),

- issue of MCMD "BITE" with a test 16-digit word to fill RH memory

with test information (by initiating program А11 in input 6),

- issue of MCMD "Mode selection" to memorize "prototype" in "Pamela"

RH and to set no-file read mode (by initiating program А11 in input 6),

- managing four HSRL exchange sessions (by successive fourfold refer-

ence to program А11 in input 10),

- the hardware change over to operational mode А0 (by initiating pro-

gram А11 in input 6),

- issue of MCMD "Memory packing" to activate memory module В (by

initiating program А11 in input 6),

- issue of MCMD "BITE" with a test 16-digit word to fill RH memory

with test information (by initiating program А11 in input 6),

- issue of MCMD "Mode selection" to memorize "prototype" in "Pamela"

RH (by initiating program А11 in input 6),

- managing the fifth HSRL exchange session (by initiating program А11

in input 10),

353П-46КС-27895-1105 63

- issue of MCMD "Memory packing" to activate memory module A (by

initiating program А11 in input 6),

- "Pamela" RH deactivation by initiating program А11 in input 2.

In the third fragment five exchange sessions are provided: with a main ex-

change adapter in the primary and standby sub-channel №19, with a standby ex-

change adapter in the primary and standby sub-channel №19, the fifth exchange

session is executed with a main adapter in the primary exchange channel.

In this fragment memory module A is active during sessions 1, 2, 3 and

memory module B – during session 5.

To perform this test assembly program ПрБ1 and operational mode

"ЗАП8" of BDTS are initiated not late than 1minute prior the first activation of

HSRL.

For debugging of fragment 3 RAM Program 42 forms the following ID:










- GV "КДБЗ"=528;

- GV "ВРКАН"=0 for exchange sessions 1,3 and 5, =1 for sessions 2 and

4;

- GV "ВРАДАП"=0 for exchange sessions 1, 2 and 5, =1 for sessions 3

and 4;

- GV "ВРИОК=1";

- MCMD "Memory packing";

353П-46КС-27895-1105 64

- MCMD "Mode selection"(2 types – for change over to mode А0 and for

making the prototype);

- MCMD "BITE";

- МП2 array.

MCMD: "BITE", "Memory packing", "Mode selection" are given in table

9.

МП2 array including 5 sub-arrays with route characteristics (one for each

exchange session) is given in Fig 7.

"Pamela" RH

ХР5 ХР6

Input com-

mutator

HSRLOB

FTD

(Volume = 20

Gb)

FAST ETHERNET(100 м)

"Pamela" RH

GSE

HSRL GTE

Figure 6 "Pamela" RH GSE/HSRL OBE GTE connection diagram

Cable type –

STR (кат.5)

353П-46КС-27895-1105 65

Table 9 MCMD, formed by RAM program 43 for fragment 2 of Pamela/

HSRL test activations.

MCMD EXE_MEM_CONF 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

Counter MCMD =0

0 Code MCMD =2916

Length MCMD =7



ПВВМ ПВМП

CW

ПВМП – memory module selection flag =0, if memory module A is selected, and

=1 if memory module B is selected

ПВВМ – flag of activation/ deactivation of the selected memory module.

Table 9 cont’d.

MCMD "BITE" 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

Counter MCMD =0

0 Code MCMD =8016

Length MCMD =7



1 1 1 0 0 0 1 1 1 0 0 0 1 1 1

CW

Table 9 cont’d

MCMD Select Mode

353П-46КС-27895-1105 66

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

Counter MCMD =0

0 Code MCMD = 3316

Length MCMD = ?



CW=0

Table 9 cont’d 9.

MCMD Select Mode

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

Counter MCMD К=0

0 Code MCMD = 3316

Length MCMD = ?



CW=0

Data field

Data field

353П-46КС-27895-1105 67

МП2 (1) 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1

ТНОИ=0 2

КРСР КСН

ПМХСМ

НА

3

НА

2

НА

1 КМАР=2 3


//////////////////////// ДЛСН1 6 ТНСН2 7

//////////////////////// ДЛСН2 8 ТНСН3 9

//////////////////////// ДЛСН3 10 ///////////////////////////////////// ПКАС ПД /////////// 11


//////////////////

ПРБ

А13

ПРБ

А23

СП3

ПРБ

А12

ПРБ

А22

СП2

ПРБ

А11

ПРБ

А21

СП1 ///// 13

//////////////////////////////////////////////////////////////// НЧК3 НЧК2 НЧК1 14 ПХМ1

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 00 /////////////////////////////// КМАРР=1 КРНА=1110 1

ДЛМ =200с 2 ТНМ=20 min 3

СДИ* 4 /////////////////////////////////////////////////////////////////////////////////////////////////////// 5



////////////////////////////////////////////

ПВКЗУ

ПС /////////// НМВ=1 10

00000 00 0 0 0000000 11

0 0000000 0 0000000 12

353П-46КС-27895-1105 68

С К МЭ Т1 Т2 Т3 /////////// РФСЧ ///////////////////////////////////// 13 КСНР1 КСНВ1 КСНН1 ///// НРЗ1 14 КСНР2 КСНВ2 КСНН2 ///// НРЗ2 15 КСНР3 КСНВ3 КСНН3 ///// НР33 16 КС1 КС2 КС3 /////////////////////////////// РВО 17

ПХМ2 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

00 /////////////////////////////// КМАРР=1 КРНА=1110 1 ДЛМ =200с 2 ТНМ=30 min 3

СДИ* 4 /////////////////////////////////////////////////////////////////////////////////////////////////////// 5



////////////////////////////////////////////

ПВКЗУ

ПС /////////// НМВ=2 10

00000 00 0 0 0000000 11


МХСМ

МП2 (2)

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1

ТНОИ=0 2

КРСР КСН

ПМХСМ

НА

3

НА

2

НА

1 КМАР=2 3


//////////////////////// ДЛСН1 6

353П-46КС-27895-1105 69

ТНСН2 7 //////////////////////// ДЛСН2 8

ТНСН3 9 //////////////////////// ДЛСН3 10 ///////////////////////////////////// ПКАС ПД /////////// 11


////////////////// ПРБ

А13

ПРБ

А23

СП3

ПРБ

А12

ПРБ

А22

СП2

ПРБ

А11

ПРБ

А21

СП1 ///// 13

//////////////////////////////////////////////////////////////// НЧК3 НЧК2 НЧК1 14 ПХМ1

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 00 /////////////////////////////// КМАРР=1 КРНА=1110 1

ДЛМ =200с 2 ТНМ=40 min 3

СДИ* 4 /////////////////////////////////////////////////////////////////////////////////////////////////////// 5



////////////////////////////////////////////

ПВКЗУ

ПС /////////// НМВ=1 10

00000 00 0 0 0000000 11


ПХМ2 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1


СДИ* 4 /////////////////////////////////////////////////////////////////////////////////////////////////////// 5

ДЛС 6

353П-46КС-27895-1105 70

ДЛЗНП (ДЛАП2) 7 СПК2 НПК2 (НМП2) СПК1 НПК1 (НМП1) 8 СПК4 НПК4 (НМП4) СПК3 НПК3 (НМП3) 9

////////////////////////////////////////////

ПВКЗУ

ПС /////////// НМВ=2 10

00000 00 0 0 0000000 11


МХСМ

МП2 (3)

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1

ТНОИ=0 2

КРСР КСН

ПМХСМ

НА

3

НА

2

НА

1 КМАР=1 3


//////////////////////// ДЛСН1 6 ТНСН2 7

//////////////////////// ДЛСН2 8 ТНСН3 9

//////////////////////// ДЛСН3 10 ///////////////////////////////////// ПКАС ПД /////////// 11


//////////////////

ПРБ

А13

ПРБ

А23

СП3

ПРБ

А12

ПРБ

А22

СП2

ПРБ

А11

ПРБ

А21

СП1 ///// 13

//////////////////////////////////////////////////////////////// НЧК3 НЧК2 НЧК1 14 ПХМ1

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

353П-46КС-27895-1105 71


СДИ* 4 /////////////////////////////////////////////////////////////////////////////////////////////////////// 5



////////////////////////////////////////////

ПВКЗУ

ПС /////////// НМВ=1 10

00000 00 0 0 0000000 11


МХСМ

Figure 7 Memory array 2 for fragment 2 of Pamela/HSRL testing activation.

Note: Parameters, used by Pamela and HSRL are marked in thick print.

The other parameters will be assigned as zero.

All commands, sent to Pamela during the second fragment of Pam-

ela/HSRL testing activation, are given in Table 2.

Table 10

Type of com-

mand

Name of com-

mand

Time of the command issue Place from

which the

command

is issued.


353П-46КС-27895-1105 72

Type of com-

mand

Name of com-

mand


which the

command

is issued.




А11

CC "PSCU ON

SPARE"

230 s + t0 А11



action test via

MCL" (ses Ta-

ble 1)

351 s + t0



CC "IPM 2 ON" 354 s + t0 А11

CC "IPM 4 ON" 354 s 250 мs + t0 А11

CC "IPM 6 ON" 354 s 500 мs + t0 А11

CC "GAS EN-

ABLE"

А11





CC ND power bus on

А11

CC "ND ON" А11

353П-46КС-27895-1105 73

Type of com-

mand

Name of com-

mand


which the

command

is issued.

CC ND spare low

voltage

А11

CC ND spare high

voltage

А11


MCMD "BITE" 570 s + t0 А11



MCMD Time Sync 1180 s + t0 А11

MCMD "Select Mode" А11




MCMD






Third communication session




353П-46КС-27895-1105 74

Type of com-

mand

Name of com-

mand


which the

command

is issued.

MCMD СCA request А11


Fourth communication session







MCMD EXE_MEM_CO

NF

3630 s + t0 А11



Fifth communication session




MCMD ССА request А11


MCMD EXE_MEM_CO

NF

4620 s + t0 А11

"Nominal switch

OFF " (see Ta-

ble 1)

4800 s + t0 А11

353П-46КС-27895-1105 75

Research data are received by Pamela’s GSE according to 4.1.2.1.

353П-46КС-27895-1105 76

Thus during Pamela’s testing activation the following Pamela’s links are

checked: with Resource on-board computer system (by sending MCMD to Pamela

both via MCL line A and line B), with HSRL on-board equipment (by performing

five download sessions with the main and spare channels), with BTMS (by check-

ing TM-parameters with reference values), with BTCS (by sending synchro sig-

nals via channels 1 and 2), with CRPDS (by sending CC via buses Еок1 and

Еок2).

Table 11 gives the order of switching between redundant communication

channels of Pamela and BTCS, CRPDS, HSRL on-board equipment.

Table 11

CC name Check in bus Еок1

Check in bus Еок2

Exchange via MCL

bus A

Exchange via MCL

bus В

Cha

nnel

1

of .

BTC

S

Cha

nnel

2

of

BTC

S

1. Main PSCU on

frag.1 PAM TA

frag.1 PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

2. PSCU off frag.1 of

PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

3. Spare PSCU on

frag.1 of

PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

4. PSCU reset frag.1 of

PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

5. IPM 1 on frag.1 of

PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

6. IPM1-2 off frag.1 of

PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\


PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\


PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

9. IPM 3-4 off frag.1 of

PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

353П-46КС-27895-1105 77



Exchange via MCL

bus A

Exchange via MCL

bus В

Cha

nnel

1

of .

BTC

S

Cha

nnel

2

of

BTC

S


PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\


PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

12. IPM 5-6 off frag.1 of

PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\


PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

14. Safe mode on

frag.1 of

PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

15. Safe mode off

frag.1 of

PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

16. ND on frag.1 of

PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

17. ND off frag.1 of

PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

18. ND main high voltage

frag.1 of

PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

19. ND spare high voltage

frag.1 of

PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

20. ND main low voltage

frag.1 of

PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

21. ND spare low voltage

frag.1 of

PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

22. GS on frag.1 of

PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

23. GS off frag.1 of

PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

24. GS enable frag.1 of

PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

353П-46КС-27895-1105 78



Exchange via MCL

bus A

Exchange via MCL

bus В

Cha

nnel

1

of .

BTC

S

Cha

nnel

2

of

BTC

S

25.GS disable frag.1 of

PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

26. Pamela power bus on

frag.1 of

PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

27.Pamela power bus off

frag.1 of

PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

28.ND power bus on

frag.1 of

PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

29.ND power bus off

frag.1 of

PAM TA

frag.1 of

PAM TA

\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\\\\ \\\\\\\\

MCDM \\\\\\\\\\\\\\ \\\\\\\\\\\\\\ frag. 1 of PAM TA2

frag. 1, 2 of PAM

TA

\\\\\\\\\\\\ \\\\\\\\

Synchro signals \\\\\\\\\\\\\\ \\\\\\\\\\\\\\ \\\\\\\\\\ \\\\\\\\\\\ frag.1 of PAM TA

frag.1,2of

PAM TA

2 TA=Testing activation

353П-46КС-27895-1105 79

CD-computer data

inp.- input

ms-marshrut (route start)

TSD-time scale digitization

Figure 7. Time diagram of fragment 2 of Pamela/HSRL testing switch (beginning)

2 com.sess.

УВИД8=33min20s+ tTSD УВИД9=43min20s+ tTSD

4 comm.sess УВИД10=53min20s+ tTSD

CDА11-

УВИД7=23min20s+tTSD

ЖР67 inp.7

УВИД1=3s+tTSD

А11 inp.1 (on.) ПрОЗУ13

inp.1

УВИД2=8min 30s+ tTSD

ИОК

А11-2

УВИД3=9min10s+ tTSD А11in.6 MCMC

("select mode")

УВИД4=9min 30s+ tTSD

A40 inp.

ИОК

А11-2

А11

МТ

t0+20min Тнм2

t0+21min

Тms3

t0+30min

Тнм4

t0+50min

t0=tTSD=0

А11 inp.6 (MCMD

"BITE")

УВИД5=10min+tTSD УВИД6=15min+ tTSD А11inp.6 (MCMD

"Select mode") Тms1

3 comm.sess.

t0+40min

Transfer into mode А0

Making "imitating model"

ИОК

А11-2

353П-46КС-27895-1105 80

ИОК

А11-2

А11 inp.6 (MCMD

"memory packing")

УВИД16=77min+ tTSD

Memory module В.

А11 inp.6 (MCMD "se-

lect mode")

А11 inp.6 (MCMD

"BITE")

УВИД12=60min30s+tTSD УВИД13=61min+ tTSD УВИ11=60min+ tTSD

А11 inp.6 (MCMD "Se-

lect Mode") А11 inp.6 (MCMD

"memory packing.")

RH transfer into AF mode

УВИД14=61min30с+ tTSD

Create "simulation sample"

УВИД15=75min20s+ tTSD

5 comm.sess.

Тнм5

t0+72 min

Memory module А

А11 inp.2

(0ff)

УВИД17=80min+ tTSD

Figure 7 Time diagram of fragment 2 of Pamela/HSRL testing switch (end).

353П-46КС-27895-1105 81

353П-46КС-27895-1105 82

5. Joint Operation of Pamela and HSRL

During this testing phase operation of Pamela and HSRL on-board equip-

ment will be checked when research data (test data) are being downloaded from

Pamela’s memory into the target data memory of HSRL on-board equipment.

Before joint operation HSRL should be re-activated without warming-up.

Joint operation is performed using RAM program 45 " Pamela ‘s control

during download session", ЖP68, RAM program 13 " HSRL on-board equipment

control during download session " and testing program ОР63 of department 1107.

Pamela’s GSE/HSRL testing equipment is given in Fig.12.

Time diagram is given in Materials of electric and diagnostic tests of HSRL

(353П-46КС-23286-1107).



Pamela is planned to be switched on by A11 program activation via input

1. After four download sessions Pamela is planned to be switched off by A11 pro-

gram activation via input 2.

The first download session is performed with the main adapter in the main

sub-channel #19, the second one is performed with the main adapter in the spare

sub-channel #19, the third one is with the spare adapter in the main sub-channel

#19, the fourth is with the spare adapter in the spare sub-channel #19.

Before each download session (at least 3 minutes before it starts) RAM

program 43 arranges the issue of "BITE” MCMD with the test 16-bit word by acti-

vation of A11 program via input 6. During joint operation with Pamela RAM pro-

gram 43 forms the following initial data for A11 program:




- GV "ВРБУЗП"=0

- GV "ВРНИЗН"=0

353П-46КС-27895-1105 83

- GV "ВРВЫСН"=0




- GV "КДБЗ"=258;

- GV "НРНД"=0;

- GV "ВРКАН"=0 for download sessions 1 and 3, =1 for download ses-

sions 2 and 4;

- GV П "ВРАДАП=0 for download sessions 1 and 2, =1 for download

sessions 3 and 4;

- GV GV "ВРИОК=1";

- “Select mode” MCMD (to transfer Pamela into the standby mode);

- "BITE" MCMD.

"BITE" MCMD is given in Table 8.

Table 8.

MCMD "BITE" 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

Counter MCMD =0

0 Code MCMD =8016

Length MCMD =7



CW=0

TW1=**********;

TW2=**********;

TW3=**********;

TW4=**********.

Test word (TWi)

353П-46КС-27895-1105 84

RAM program 43 forms Memory array 2 for joint operation.

Fig. 3 shows memory arrays 2 for joint operation of Pamela and HSRL.

МП2 (1) 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1

ТНОИ=0 2

КРСР КСН

ПМХСМ

НА

3

НА

2

НА

1 КМАР=2 3


//////////////////////// ДЛСН1 6 ТНСН2 7

//////////////////////// ДЛСН2 8 ТНСН3 9

//////////////////////// ДЛСН3 10 ///////////////////////////////////// ПКАС ПД /////////// 11


//////////////////

ПРБ

А13

ПРБ

А23

СП3

ПРБ

А12

ПРБ

А22

СП2

ПРБ

А11

ПРБ

А21

СП1 ///// 13

//////////////////////////////////////////////////////////////// НЧК3 НЧК2 НЧК1 14 ПХМ1

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 00 /////////////////////////////// КМАРР КРНА=1110 1

ДЛМ =200с 2 ТНМ=900с 3

СДИ* 4 /////////////////////////////////////////////////////////////////////////////////////////////////////// 5



////////////////////////////////////////////

ПВКЗУ

ПС /////////// НМВ=1 10

00000 00 0 0 0000000 11

353П-46КС-27895-1105 85


ПХМ2 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

00 /////////////////////////////// КМАРР КРНА=1110 1 ДЛМ =200с 2 ТНМ=1400с 3

СДИ* 4 /////////////////////////////////////////////////////////////////////////////////////////////////////// 5



////////////////////////////////////////////

ПВКЗУ

ПС /////////// НМВ=2 10

00000 00 0 0 0000000 11


МХСМ

МП2 (2)

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1

ТНОИ=0 2

КРСР КСН

ПМХСМ

НА

3

НА

2

НА

1 КМАР=2 3


353П-46КС-27895-1105 86

//////////////////////// ДЛСН1 6 ТНСН2 7

//////////////////////// ДЛСН2 8 ТНСН3 9

//////////////////////// ДЛСН3 10 ///////////////////////////////////// ПКАС ПД /////////// 11


//////////////////

ПРБ

А13

ПРБ

А23

СП3

ПРБ

А12

ПРБ

А22

СП2

ПРБ

А11

ПРБ

А21

СП1 ///// 13

//////////////////////////////////////////////////////////////// НЧК3 НЧК2 НЧК1 14 ПХМ1

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 00 /////////////////////////////// КМАРР КРНА=1110 1

ДЛМ =200с 2 ТНМ=1900с 3

СДИ* 4 /////////////////////////////////////////////////////////////////////////////////////////////////////// 5



////////////////////////////////////////////

ПВКЗУ

ПС /////////// НМВ=1 10

00000 00 0 0 0000000 11


ПХМ2 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

00 /////////////////////////////// КМАРР КРНА=1110 1 ДЛМ =200с 2 ТНМ=2400с 3

СДИ* 4 /////////////////////////////////////////////////////////////////////////////////////////////////////// 5

353П-46КС-27895-1105 87



////////////////////////////////////////////

ПВКЗУ

ПС /////////// НМВ=2 10

00000 00 0 0 0000000 11


МХСМ

Figure 8 Memory array 2 for joint operation.

Note: Parameters, used by Pamela and HSRL, are marked in thick print.

The other parameters will be assigned as “zero”.

All commands, sent to Pamela during joint operation, are given in Table 4.

Table 12 Commands, sent to Pamela during joint operation.

Type of com-

mand

Name of com-

mand


where the

command

is issued





А11

353П-46КС-27895-1105 88

Type of com-

mand

Name of com-

mand


where the

command

is issued

CC "PSCU ON

MAINE"

230 s + t0 А11

MCMD CC request 350 s + t0 А11


action test via

MCL" (see Ta-

ble. 1)

351 s + t0

MCMD Time sync 352 s + t0

MCMD CC request 353s + t0 А11

CC "IPM 1 ON" 354 s + t0 А11

CC "IPM 3 ON" 354 s 250 мs + t0 А11

CC "IPM 5 ON" 354 s 500 мs + t0 А11

CC "GAS EN-

ABLE"

А11





CC ND power bus on

А11

CC "ND ON" А11

CC ND main low

voltage

А11

353П-46КС-27895-1105 89

Type of com-

mand

Name of com-

mand


where the

command

is issued

CC ND main high

voltage

А11

MCMD "Select Mode"" 550 s + t0 А11




MCMD "Time sync" 880 s + t0 А11



MCMD CCA request А11

MCMD CCA request 1103 s + t0 А11


Second communication session







Third comunication session



353П-46КС-27895-1105 90

Type of com-

mand

Name of com-

mand


where the

command

is issued





Fourth communication session






"Nominal switch

off" (см табл. 1)

4800 s + t0 А11

Research data are received by Pamela’s GSE according to 4.2.1.1, but

HSRL testing equipment takes data from the nominal output of HSRL on-board

equipment.

353П-46КС-27895-1105 91

Pamela

ХР5 ХР6

HSRL OBE FTD

(Size = 20

Gbyte)

100 m

Pamela’s

GSE

HSRL GTE

Figure 9 Layout of Pamela’s GSE and HSRL GTE

during joint operation.

353П-46КС-27895-1105 92

6. INTEGRATED TESTS OF PAMELA

During integrated tests all initial data for Pamela are assigned in the opera-

tional program.

Pamela’s participation in the integrated tests of “Resource-DK” SC implies

the following items:

1) Before the beginning of the first mode Р10 Pamela is switched on

nominally (by activation of A11 program via input 1 from the operational pro-

gram);

2) After finishing the activation process (at least 550 seconds after A11 ac-

tivation via input 1) the following MCMDs are sent to Pamela:

- MCMD “Select Mode” (1) to transfer Pamela into the stand –by mode

(for this purpose MCMD “Select Mode” should be included into RAM area of

A11 program, starting with the GV”MCMD.CODE5”, A11 program should be

activated by input 6),

- “BITE”MCMD to fill Pamela’s memory with test data (for this pur-

pose MCMD "BITE" should be included into RAM area of A11 program, start-

ing with the GV ”MCMD.CODE5”, A11 program should be activated by input

6).

- 10 seconds later MCMD “Select Mode” (2) to make the imitating

model in Pamela’s memory (for this purpose MCMD “Select Mode” should be

included into RAM area of A11 program, starting with the GV

”MCMD.CODE5”, A11 program should be activated by input 6).

3) Between 5 and 6 min later Pamela participates in the first download ses-

sion with HSRL OBE in the first mode P10 (by activation of program A11via input

10 from program Р10), download session lasts 200 seconds;

4) When the first download session is finished (10 seconds later), the fol-

lowing MCMD are sent to Pamela:

- MCMD “Select Mode” (3) to make the imitating model in Pamela’s

memory (for this purpose MCMD “Select Mode” should be included into

353П-46КС-27895-1105 93

RAM area of A11 program, starting with the GV ”MCMD.CODE5”, A11 pro-

gram should be activated by input 6).

- 2 to 5 minutes after issue of MCMD according to item 4) MCMD “Se-

lect Mode” (4) is issued with the initial data to calibrate Pamela (for this pur-

pose MCMD “Select Mode” should be included into RAM area of A11 pro-

gram, starting with the GV ”MCMD.CODE5”, A11 program should be acti-

vated by input 6).

- 10 seconds later “Calibrate” MCMD is issued (by activation of A11

program via input 37)

- 3 minutes after “Calibrate” MCMD issue, MCMD “Select Mode” (5)

is issued to transfer Pamela into the mode of particle counting (for this purpose

MCMD “Select Mode” should be included into RAM area of A11 program,

starting with the GV ”MCMD.CODE5”, A11 program should be activated by

input 6).

5) Between 1 and 2 hours later Pamela participates in the second

download session with HSRL OBE (in the 3d mode P10), download session

lasts 200 seconds.

6) Pamela is switched off nominally (by activation of program

A11 via input 2 from the operational program).

The following initial data should be formed before A11 program activation

via input 1:

-GV "ЗВРПК"=1;


- GV "КДБЗ"=258;






353П-46КС-27895-1105 94

- GV "НРНД"=0.

5 “Select Mode” MCMDs, “BITE” MCMD , formed for Pamela with

checking information, are given in Table 5.

Table 13

MCMD "Select Mode" (1) 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

Counter MCMD=0

0 Code MCMD= 3316

Length MCMD=?



CW

MCMD "Select Mode" (2) 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

Counter MCMD =0

0 Code MCMD= 3316

Length MCMD=?



CW

MCMD "Select Mode" (3) 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

353П-46КС-27895-1105 95

Counter MCMD=0

0 Code MCMD= 3316

Length MCMD=?



CW

MCMD "Select Mode" (4) 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

Counter MCMD=0

0 Code MCMD= 3316

Length MCMD=?



CW

MCMD "Select Mode" (5) 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

Counter MCMD=0

0 Code MCMD= 3316

Length MCMD=?



353П-46КС-27895-1105 96

CW=0

MCMD"BITE" 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

Counter MCMD=0

0 Code MCMD=8016

Length MCMD=7



CW

The following initial data should be formed before activation of A11 pro-

gram via input 10 (in the first and the third modes P10):

- GV "ВРКАН"=0;

- GV "ВРАДАП"=0;

- GV "ВРИОК=1".

Subarrays of route (marshrut) characteristics should be formed too with

КРНА (code of Pamela’s operation)=168, marshrut length=200s, time of marshrut

start, number of marshrut in orbit.

Additions will be put to data of table 5.

ЖР69 testing program should be activated by inputs:

- by input 1 to check Pamela’s temperature parameters. In case of anom-

aly in any of these parameters ЖР69 program forms GV

"ННТМПП"=1 (anomaly in Pamela’s temperature parameters) for the

planning program КР18. Time of ЖР69 program operation by input 1

does not exceed 3 minutes.

Test word

353П-46КС-27895-1105 97

- by input 2 and 3 to control Pamela’s switching on and off. Time of

ЖР69 program operation by input 2 does not exceed 10 minutes. Time

of ЖР69 program operation by input 3 does not exceed 1 minute.

- by input 4 for periodic control of Pamela’s status throughout the whole

activation (between P10). Time of ЖР69 program operation by input 4

does not exceed 4 minutes.

Pamela’s GSE receives research data according to 4.2.1.1, but HSRL GTE

takes data from the nominal HSRL output.

353П-46КС-27895-1105 98

7. AMOUNT OF PAMELA’S RETESTING AFTER REPLACEMENT OF

ITS COMPONENTS OR REPLACEMENT OF “RESOURCE DK” SC

SUPPORT SYSTEMS

After replacement of Pamela’s components as well as “Resource DK” SC

systems or units connected with Pamela, test activation using “Resource DK” SC

support systems should be repeated within the following amount:

- for replacement of on-board computer system, CRPDS, BDTS, BTCS –

fragment 1 of Pamela’s test activation;

- for replacement of HSRL – fragment 2 of Pamela’s test activation with

HSRL;

- for replacement of Pamela’s components – full Pamela’s test activation

and full Pamela’s test activation with HSRL;

353П-46КС-27895-1105 99

8. Estimation of operating time

Automated estimation of Pamela’s operating time in hours is made by signalling

parameter "ПИТ ПАМ" (Pamela’s power supply) by summation of times when

this parameter is in the closed status.

Estimation of the number of Pamela’s activations is also made by signaling

parameter "ПИТ ПАМ" (Pamela’s power supply) by summation of the number of

closures of this parameter.

353П-46КС-27895-1105 100

9. ORDER OF PAMELA’S ACTIVATION, DEACTIVATION AND RE-

SET

Before Pamela’s activation, make sure that all Pamela’s connectors are

mated nominally, besides display "PAM CMC" shall be highlighted on digital

typewriter.

Activation of the hardware during TA with support systems of the article

(PAM TA and PAM/HSRL TA) and also during JO and IT is executed by nominal

program А11 (except PAM TA fragment 1). Prior activation of the hardware the

following support systems of the article shall be connected and ready for work:

BCtS, CRPDS, BDTS in modes ЗАП4, ПрБ1, BTCS, HSRL OBE (if necessary).

The hardware is completely deactivated during nominal operation under

CC "OFF PSCU", issued by program А11.

If emergent deactivation of the hardware is necessary the following CC se-

quence shall be issued:

"IPM 1-2 off", " IPM 3-4 off", " IPM 5-6 off", "PSCU off", "ND off", "GS

off", "GS stand-by", "ND power bus off", "Pamela’s power bus off".

In emergent power cut off from the article it is necessary to initiate test

program ЖР67 in input 6 after power restoration to issue the above commands.

Then work with "Pamela" RH in normal mode of operation.

Initial condition of "Pamela" RH is regarded as its deactivated condition it

is in after nominal deactivation of the hardware. Initial condition of "Pamela" RH

ПС-parameters is as follows:

"PAM P"=0, "ND"=0.

353П-46КС-27895-1105 101

353П-46КС-27895-1105 102

Figure 9 Time diagram of fragment 2 of Pamela’s test activation.

А11 inp. 6

ЖР67 inp.1 ПрОЗУ t0=tCTS=0

MC

MD

"Se

lect

Mod

e"(А

2)

ЖР67 inp.2

ПрОЗУ 42

МТ

А11 inp.1

RH in В4

mode

А11 inp. 6

УВИД1=9 min+tTSD УВИД2=10min+ttsdУВИД4=15min+tTSD

MC

MD

"D

UM

P"

MCMD "PATCH"

УВИД3=12min+ttsd

MCMD "DUMP"

УВИД5=18 min +tTSD УВИД6=19 min +tTSD УВИД7=20 min +tTSD

RAM dump

А11in.15

MC

MD

"R

ESET

HIS

TOR

Y

AR

EA"

А11 inp. 2(0ff)

History area

read

УВИД8=22 min +tTSD УВИД9=23 min +tTSD

History area read

А11 inp. 6А11 inp. 15

А11 inp.6 А11 inp.6 А11 inp.15 А11 inp15

УВИД10=25 min +tTSD А11 inp.6

А11 inp.15

УВИД11=40 min +tTSD

РР84 inp.4

t0+18 min ON CF and

establish-

ment of

t0+22min. с/с OFF

РР84 inp.5

СРК62 СРК112

УВИД=3s+tTSD A40 inp.1

353П-46КС-27895-1105 103


ЖР67 inp.3 А11 inp.1 (On)

ПрОЗУ42

МТ УВИД1=3s+tTSD

УВИД2=540s+tTSD УВИД3=662s+tTSD УВИД4=7ч 662s+tTSD

А11 inp.6 А11 inp.6

TRD purg-

ing

30s 120s

А0 mode

А11 inp.2

(Off)

PC

purging

А11 inp.6 420s

УВИД5=7ч1083s+ tTSD

ЖР67 inp.3

А11 inp.1 (On)A40 inp.1

МТ

t0=tTSD=0


А11 inp.2

(Off)

УВИД4=724s+tTSD

А11 inp.6 А11 inp.6

TRD

purging

PC jettison-

ing

30s 120s

Mode А0

А11 inp.6

420s

60s

УВИД5=1145s+ tTSD


УВИД=3s+tTSD

ЖР67 inp.1

A40 inp.1

t0=tTSD=0

ПрОЗУ 42 ЖР67 inp.1

Documents

Sender TsSKB - wischnew/pamela/internal/daq/ResursPamel… · Sender TsSKB Subject: Electro-Diagnostic Test of PAMELA RH Prot N° Year # of pages R1.d.1 377bis 03 103 Receiving data