Sec 40 BSR Series Rakes Layout 1 - Bush Hog · 2020-02-20 · MODELS BSR8, BSR10 & BSR12. 40-1-7 BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018 Item Part No Description

PARTS MANUALSECTION 40

Published 08/15 - Revised 08/18 MATERIAL HANDLING PARTS MANUAL

BSR8 HAY RAKEBSR10 HAY RAKE BSR12 HAY RAKE

SUSPENSION RAKE

©2009 Alamo Group Inc.

PARTS ORDERING GUIDE

The following instructions are offered to help eliminate needless delay and error in pro-cessing purchase orders for the equipment in this section.

1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required.

2. The Purchase Order must include the name and address of the person or organiza-tion ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered.

3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part.

4. The Manufacturer reserves the right to substitute parts where applicable.

5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order.

6. The Manufacturer reserves the right to change prices without prior notice.

For maximum safety and to guarantee optimum product reliability, always use genuine BUSH HOG Parts. The use of inferior replacement parts may causepremature or catastrophic failure which could result in serious injury or death.Direct any questions regarding parts to:

BUSH HOG2501 Griffin Ave. Selma, AL 36703www.bushhog.comContact Us800-304-2836

To the Owner/Operator/Dealer

All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-mindedoperator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer hasdesigned this implement to be used with all its safety equipment properly attached to minimize the chance ofaccidents.

BEFORE YOU START! Read the safety messages on the implement and shown in your manual. Observe the rulesof safety and common sense!

WARRANTY INFORMATION:Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty RegistrationForm in full and return it to within 30 Days. Make certain the Serial Number of the Machine is recorded on theWarranty Card and on the Warranty Form that you retain.

LIMITED WARRANTY

Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized BushHog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year fornon-commercial, state and municipalities’ use and ninety (90) days for commercial use from date of retail sale. Theobligation of Bush Hog to the purchaser under this warranty is limited to the repair or replacement of defectiveparts.

Replacement or repair parts installed in the equipment covered by this limited warranty are warranted for ninety(90) days from the date of purchase of such part or to the expiration of the applicable new equipment warrantyperiod, whichever occurs later. Warranted parts shall be provided at no cost to the user at an authorized Bush Hogdealer during regular working hours. Bush Hog reserves the right to inspect any equipment or parts which areclaimed to have been defective in material or workmanship.

DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGESBush Hog’s obligation under this limited warranty, to the extent allowed by law, is in lieu of all warranties, implied orexpressed, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR APARTICULAR PURPOSE and any liability for incidental and consequential damages with respect to the sale oruse of the items warranted. Such incidental and consequential damages shall include but not be limited to:transportation charges other than normal freight charges; cost of installation other than cost approved by BushHog; duty; taxes; charges for normal service or adjustment; loss of crops or any other loss of income; rental ofsubstitute equipment, expenses due to loss, damage, detention or delay in the delivery of equipment or partsresulting from acts beyond the control of Bush Hog.

THIS LIMITED WARRANTY SHALL NOT APPLY:1. To vendor items which carry their own warranties, such as engines, tires, and tubes.

2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident.

3. If parts not made or supplied by Bush Hog have been used in connection with the unit, if, in the sole judgementof Bush Hog such use affects its performance, stability or reliability.

4. If the unit has been altered or repaired outside of an authorized Bush Hog dealership in a manner which, in thesole judgement of Bush Hog, affects its performance, stability or reliability.

5. To normal maintenance service and normal replacement items such as gearbox lubricant, hydraulic fluid, wornblades, or to normal deterioration of such things as belts and exterior finish due to use or exposure.

6. To expendable or wear items such as teeth, chains, sprockets, belts, springs and any other items that in thecompany’s sole judgement is a wear item.

NO EMPLOYEE OR REPRESENTATIVE OF BUSH HOG IS AUTHORIZED TO CHANGE THIS LIMITEDWARRANTY IN ANY WAY OR GRANT ANY OTHER WARRANTY UNLESS SUCH CHANGE IS MADE INWRITING AND SIGNED BY BUSH HOG’S SERVICE MANAGER, 2501 GRIFFIN AVE., SELMA, ALABAMA36703.

Record the model number, serial number and date

purchased. This information will be helpful to your

dealer if parts or service are required.

MAKE CERTAIN THE WARRANTY

HAS BEEN FILED WITH BUSH HOG

SELMA, ALABAMA

MODEL NUMBER ________________________________

SERIAL NUMBER ________________________________

DATE OF RETAIL SALE ___________________________

BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018

TABLE OF CONTENTSBSR SUSPENSION RAKE

ITEM PAGE NUMBER

Center Frame & Related Parts - BSR8 & BSR10. . . . . . . . . . . . . . . . . . . .40-1-2, 40-1-3

Center Frame & Related Parts - BSR12 . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1-4, 40-1-5

RH Wheel Arm Assy, Short Arm Assy and Wing Frame . . . . . . . . . . . . . . .40-1-6, 40-1-7

LH Wheel Arm Assy, Short Arm Assy and Wing Frame . . . . . . . . . . . . . . .40-1-8, 40-1-9

Wheels & LH & RH Rake Arm Assembly . . . . . . . . . . . . . . . . . . . . . . . .40-1-10, 40-1-11

Rake Arm Hub & Spindle Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1-12

Hydraulic Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-1-13

Leveling Valve Kit (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1-13

Hydraulic Cylinder - Kicker Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1-14, 40-1-15

Hydraulic Cylinder - Wing Lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1-16

Kicker Wheel Kit (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1-17

Hydraulic Kit, Kicker Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1-18

Rake Wheel & Tire Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1-19

Led Light Kit (Rear Light Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1-20

Reduced Ground Pressure Cam Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1-21

Ground Pressure Cam Kit w/Dowel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1-22

Wing Set Plate Slotted Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-1-23

40-1-1

40-1-2


1816

1719

203

32

21

22

4

15

14

10

8

5

9

7

6

12

13

11

1E

NH

AN

CE

MO

DU

LE(L

ED

LIG

HT

KIT

)

23

25

2423

26

27

CENTER FRAMEAND RELATED PARTS

MODELS BSR8 & BSR10

40-1-3


Item Part No. Description Qty.

1 50072845 Center Frame Weldment 1

2 50073508 Decal, Haymaker 2

3 D617 Decal, Oil Leak High Pressure 2

4 50065309 Decal, Bush Hog 2

5 50078238 Tongue w/Decals, Modified 1

6 50073512 Decal, Important Chain 1

7 50073507 Decal, Warning Speed 1

8 D859 Decal, Genuine Parts Warning 1

9 50074260 Decal, Model - BSR Series 2

10 50072954 Hitch Weldment 1

11 50074816 Hitch Pin Assembly 2

12 20558BH Lynch Pin, 7/16” x 2” 2

13 ------- Capscrew, 5/8” x 2” Gr 5 4

14 9162000 Locknut, 5/8” Gr C 4

15 94359 Sign, SMV 1

16 2438621 Bracket, Spade - SMV Mounting 1

17 1160807 Capscrew, 1/4” x 7/8” Gr 5 2

18 15905 Lockwasher, 1/4” 2

19 15531BH Hex Nut, 1/4” 2

20 50035829 Tube, Owner’s Manual 1

21 50080009 Jackstand Assembly 1

22 ------- Machine Screw, Slt Pan Hd, #10 x 1 2

23 17020600 Flatwasher, #10 4

24 44520BH Locknut, #10 2

25 50074259 Decal, Made in USA 2

26 91074 Safety Tow Chain 1

27 D884 Decal, Warining - Jack Capacity 1

CENTER FRAME-MODIFIEDAND RELATED PARTS

MODELS BSR8 & BSR10

40-1-4


1816

1719

20

2425

2627

32

1

3

21

4

13

14

23

13

14

10

5

31

9

7

6

12

11

11

EN

CH

AN

CE

MO

DU

LE(L

ED

LIG

HT

KIT

)

32

29

30

28

22

15

28

8


MODELS BSR12

40-1-5



MODELS BSR12


1 50072845 Center Frame Weldment 1

2 50073508 Decal, Haymaker 2

3 D617 Decal, Oil Leak High Pressure 2

4 50065309 Decal, Bush Hog 2

5 50078238 Tongue w/Decals, Modified 1

6 50073512 Decal, Important Chain 1

7 50073507 Decal, Warning Speed 1

8 D859 Decal, Genuine Parts Warning 1

9 50074260 Decal, Model - BSR Series 2

10 50072954 Hitch Weldment 1

11 50074816 Hitch Pin Assembly 2

12 20558BH Lynch Pin, 7/16” x 2” 2

13 ------- Capscrew, 5/8” x 2” Gr 5 8

14 9162000 Locknut, 5/8” Gr C 8

15 94359 Sign, SMV 1

16 2438621 Bracket, Spade - SMV Mounting 1

17 1160807 Capscrew, 1/4” x 7/8” Gr 5 2

18 15905 Lockwasher, 1/4” 2

19 15531BH Hex Nut, 1/4” 2

20 50035829 Tube, Owner’s Manual 1

21 50080009 Jackstand Assembly 1

22 50073481 Assembly, Tongue Extension 1

23 50074146 Plate, Cylinder Lug 1

24 20103 Capscrew, 1” x 3” Gr 5 4

25 ------- Spacer, Cylinder 2

26 9163200 Locknut, 1” Gr C 4

27 ------- Machine Screw, Slt Pan Hd, #10 x 1 2

28 17020600 Flatwasher, #10 4

29 44520BH Locknut, #10 2

30 50074259 Decal, Made in USA 2

31 91074 Safety Tow Chain 1

32 D884 Decal, Warning - Jack Capacity 1

40-1-6


4912

1310

46

247 R

ight

Sid

e D

ual L

ED

Lam

p(L

ED

Lig

ht K

it)

11

1

3233

3231

45

14

2

1626

15

36

7

37

47 48

47

4836

415

2135

20

19

2927

1724

23

25

26

2230 18

5

38

34

39

9

38

40

50

1533

43

2826

26341

42

26

26

44

31

52

51Sp

ring

Mou

nt P

atch

Kit

Req

uire

d on

ly fo

r H

igh

Hou

r Rak

es8

RIGHT HAND WHEEL ARM ASSEMBLY, SHORT ARM ASSEMBLYAND WING FRAME w/RELATED PARTS

MODELS BSR8, BSR10 & BSR12

40-1-7


Item Part No Description Qty

1 50078208 Wheel Arm Weldment, RH 1

2 50073080 Bushing, Rake Pivot 2

3 50031212 Reflector, Amber, 2” x 9” 2

4 50031214 Reflector, Red 1

5 50073078 Hub & Spindle Assy, Rake Wheel 1

6 45187BH Capscrew, 1/2” x 3-1/2” Gr 5 1

7 15554 Locknut, 1/2” 1

8 50073496 Decal, Ground Pressure- RH 1

9 50073077 Wheel & Tire Assembly, Rake 1

10 50078206 Cam Assembly, RH 1

11 50017304 Pin, Lynch 1

12 50078203 Pin, Dowel 3/8” x 2-1/2” 1

13 50073510 Decal, RH 1

14 50076440 Pin Assembly, Pivot 1

15 1273BH Pin, Presto 9 Ga x 3” D Plated 3

16 50072918 Pin Assembly, Pivot Arm Lock 1

17 7977 Hub Assembly 1

18 50073BH Bearing, Cone Roller 1


20 7967 Seal, Triple Lip 1

21 50072962 Spindle, Single - Rake 1

22 15920 Flatwasher, 3/4” 1

23 120BH Hex Nut, Slotted 3/4”-16 UNF 1

24 121BH Cap, Hub 1

25 296 Pin, Cotter 1/8” x 1-1/2” 1

26 449BH Grease Fitting 6

27 15445 Bolt 1/2”-20UNF x 1-5/8” 5

28 15515BH Nut 1/2” -20UNF 5


29 14-6-197 Bearing Cup 1


31 20063 Capscrew, 1” x 6-1/2” Gr 5 3

32 15908BH Flatwasher, 1” Hard 4

33 9163200 Locknut, 1” Gr C 3

34 50073519 Short Arm Assy, RH w/Decals 1

35 D628 Decal, Crushing Hazard 1

36 50073511 Decal, Important Transport Latch 1

37 50076179 Roll Pin, 1/2” x 3” 1

38 50072951 Pin Assembly, Wing Angle 2

39 50072895 Wing Arm Adjustment Assembly 1

40 45328BH Capscrew, 3/4” x 6” Gr 8 2

41 15921 Flatwasher, 3/4” SAE 2

42 19517 Hex Nut, 3/4” 2

43 50078204 Wing Set Plate Weldment 1

44 50073504 Wing Frame Weldment - RH 1

45 50073087 Cylinder, Hyd. 2.5” Bore x 12” Str. 1

46 44186BH Capscrew, 1/4” x 1” Gr 5 4

47 15918BH Flatwasher, 1/4” 8

48 15608 Locknut, 1/4” 4

49 50074735 Cable Clamp 2

50 50077995 Nord Washer 1

51 50078220 Spring Mount Patch Kit 8 Wheel 1

50078221 Spring Mount Patch Kit 10 Wheel 1


52 50078219 Spring Pad Gusset 1

RIGHT HAND WHEEL ARM ASSEMBLY, SHORT ARM ASSEMBLYAND WING FRAME w/RELATED PARTS


40-1-8


52

51Sp

ring

Mou

nt P

atch

Kit

Req

uire

d on

ly fo

r H

igh

Hou

r Rak

es

928

24

25

2318 30

1727

2919

205

26

1012 132

15

3536

3831

26

40

33

5015

43

3938

26

44

3

42

41

2626

45

14

211

3437 48

47 26

156

213 7

16 49

498

4

47

46

32

33

3132

1

Left

Sid

e D

ual L

ED

Lam

p(L

ED

Lig

ht K

it)

LEFT HAND WHEEL ARM ASSEMBLY, SHORT ARM ASSEMBLYAND WING FRAME w/RELATED PARTS


40-1-9



1 50078209 Wheel Arm Weldment, LH 1

2 50073080 Bushing, Rake Pivot 2

3 50031212 Reflector, Amber, 2” x 9” 2

4 50031214 Reflector, Red 1

5 50073078 Hub & Spindle Assy, Rake Wheel 1

6 45187BH Capscrew, 1/2” x 3-1/2” Gr 5 1

7 15554 Locknut, 1/2” 1

8 50073497 Decal, Ground Pressure- LH 1

9 50073077 Wheel & Tire Assembly, Rake 1

10 50078207 Cam Assembly, LH 1

11 50017304 Pin, Lynch 1

12 50078203 Pin, Dowel 3/8” x 2-1/2” 1

13 50073509 Decal, LH 1

14 50076440 Pin Assembly, Pivot 1

15 1273BH Pin, Presto 9 Ga x 3” D Plated 3

16 50072918 Pin Assembly, Pivot Arm Lock 1

17 7977 Hub Assembly 1



20 7967 Seal, Triple Lip 1


22 15920 Flatwasher, 3/4” 1

23 120BH Hex Nut, Slotted 3/4”-16 UNF 1

24 121BH Cap, Hub 1

25 296 Pin, Cotter 1/8” x 1-1/2” 1

26 449BH Grease Fitting 6

27 15445 Bolt 1/2” -20UNF x 1-5/8” 5


28 15515BH Nut, 1/2”-20UNF 5



31 20063 Capscrew, 1” x 6-1/2” Gr 5 3


33 9163200 Locknut, 1” Gr C 3

34 50073518 Short Arm Assy, LH w/Decals 1

35 D628 Decal, Crushing Hazard 1

36 50073511 Decal, Important Transport Latch 1

37 50076179 Roll Pin, 1/2” x 3” 1

38 50072951 Pin Assembly, Wing Angle 2

39 50072895 Wing Arm Adjustment Assembly 1

40 45328BH Capscrew, 3/4” x 6” Gr 8 2

41 15921 Flatwasher, 3/4” SAE 2

42 19517 Hex Nut, 3/4” 2

43 50078204 Wing Set Plate Weldment 1

44 50073503 Wing Frame Weldment - LH 1

45 50073087 Cylinder, Hyd. 2.5” Bore x 12” Str. 1

46 44186BH Capscrew, 1/4” x 1” Gr 5 4


48 15608 Locknut, 1/4” 4

49 50074735 Cable Clamp 2

50 50077995 Nord Washer 1

51 50078220 Spring Mount Patch Kit 8 Wheel 1



52 50078219 Spring Pad Gusset 1

LEFT HAND WHEEL ARM ASSEMBLY, SHORT ARM ASSEMBLYAND WING FRAME w/RELATED PARTS


40-1-10


18

15, 1

6

1921

17

22

20

30

2716

5

2

3

264 27 28 29

LH

WIN

G

FR

AM

E

RH

WIN

G

FR

AM

E

10A

4 712

24

23

2510

B,

10C

9

14

2423

2510

B,

10C

9

13

8 10B

,10

C25

23

2410

B,

10C

811

25

23

24610

A4

15

1

5

34

26

2729 28

6

10A

10A

7

WHEELS & LH & RH RAKE ARMASSEMBLY w/RELATED PARTSMODELS BSR8, BSR10 & BSR12

40-1-11


WHEELS & LH & RH RAKE ARMASSEMBLY w/RELATED PARTSMODELS BSR8, BSR10 & BSR12

Item Part No. Description Qty Qty Qty

BSR8 BSR10 BSR12

1 50075265 Assembly, Rake Arm - RH 4 5 6

2 50075266 Assembly, Rake Arm - LH 4 5 6

3 50073514 Rake Wheel Hub & Spindle Assembly 8 10 12

4 50073061 Bushing, Rake Arm 16 20 24

5 50073485 Spring, Rake Arm 8 10 12

6 50072964 Arm Stop Assembly, RH 4 4 5

7 50072978 Arm Stop Assembly, LH 4 4 5

8 50072973 Lock Pin Assembly, Front Stop - RH - 1 1

9 50072976 Lock Pin Assembly, Front Stop - LH - 1 1

10A 53065 Spiral Pin, 3/8” x 2-1/2” 8 8 10

10B 20327 (OUTER) Roll Pin, 3/8” x 2-1/2” - 2 2

10C 45325BH (INNER) Roll Pin, 7/32” x 2-1/2” - 2 2

11 50072905 Weldment, RH Wing Frame - BSR10 - 1 -

12 50072969 Weldment, LH Wing Frame - BSR10 - 1 -

13 50072970 Weldment, RH Wing Frame - BSR12 - - 1

14 50072908 Weldment, LH Wing Frame - BSR12 - - 1

15 50075555 Assy, Rake Wheel - RH 4 5 6

S/N 1HCKR1171500069 & Below

50075253 Assy, Rake Wheel - RH 4 5 6

S/N 1HCKR1171500070 & Above

16 50075554 Assy, Rake Wheel - LH 4 5 6


50075252 Assembly, Rake Wheel - LH 4 5 6


17 50074099 Flange, Rake Wheel 8 10 12


50075254 Flange, Rake Wheel 8 10 12


18 50074098 Ring, Rake Wheel 8 10 12


50075255 Ring, Rake Wheel 8 10 12


19 50074097 Finger, Rake Wheel (Set of 40) 320 400 480


50075256 Finger, Rake Wheel (Set of 40) 320 400 480


20 50074096 Plate, Clamp - Rake Wheel 80 100 120


50075257 Plate, Clamp - Rake Wheel 80 100 120


21 70631C4 Bolt, M10 x 1.5 x 25 160 200 240

22 50075259 Nut, M10 160 200 240

23 50072980 Assembly, Front Stop Lock Pin - 2 2

24 1273BH Pin, Presto 9 GA x 3” D Plated - 2 2

25 50031212 Reflector, Amber 2” x 9” - 2 2

26 1161010 Capscrew, 5/16” x 1” Gr 5 8 10 12

27 15915BH Flatwasher, 3/8” 56 70 84

28 15907BH Flatwasher, 5/16” 8 10 12

29 15528 Hex Nut, 5/16” 8 10 12

30 8151200 Hex Nut, 3/8” 48 60 72

40-1-12


RAKE ARM HUB & SPINDLE ASSEMBLY


50073514 Rake Arm Hub & Spindle Assy 1

1 50074256 Seal, Hub (N906282) 1


3 21020416 Pin, Cotter 1/8” x 1-3/4” 1

4 50074101 Washer 1

5 50074102 Hub Cap 1

6 50074103 Nut, Slotted 3/4”-16UNF 1

7 50074104 Bearing Cone (L44649) 2

8 50074100 Protector, Seal 1

9 50074257 Hub w/Studs & Cups 1

10 50074276 Rake Stud, 3/8”-16UNC x 1.25 6

11 170BH Bearing Cone, 1” Bore x .5 2

40-1-13


CYL ROD END

CYL BASEEND

1

2

2

1

3

3

4

4

5

5

6

6

HYDRAULIC KIT50073523


1 14-40-98 Elbow, 90° 4

2 50068458 Restrictor 2

3 53330BH Assembly, Hydraulic Hose, 42” 4

4 53339BH Tee, G-Flare 2

5 24-6-434 Adapter, Hyd. Str. 1/2” Male NPT x 9/16” M JIC 2

6 50015063 Assembly, Hydraulic Hose, 196” 2


1 50077055 Leveling Valve Assembly 1

2 50077057 Cartridge Assembly 2

3 53340BH Hydraulic Adapter 3

4 14-40-98 90º Elbow 1

5 6050072 Swivel Nut Tee 1

6 97339 Swivel Nut Branch Tee 1

7 ------- Instruction Sheet (50077046) 1

8 50077041 Leveling Valve Kit 1

qww

e

e

r

t

yi LEVELING VALVE KIT (Optional)

(Use to raise both arms at the same time)

40-1-14


2

98

14

1213

46 7

3

12

5

10

11

9

8

15

1

HYDRAULIC CYLINDER - KICKER WHEELBailey

(Replaced by Monarch)


1 50074129 Assembly, Hydraulic Cylinder 1

2 ------- Clevis Cap 1

3 ------- Rod Cap 1

4 ------- Piston 1

5 ------- Rod, 1.125” Dia 1

6 ------- Cylinder Tube 1

7 ------- Tie Rod 4

8 ------- Pin, 1” Dia 2

9 ------- Cotter Pin, 3/16” x 1-1/2” 4

10 ------- Rod Clevis 1

11 ------- Set Screw 1

12 ------- Hex Nut 8

13 ------- Hex Nut 1

14 ------- Plug, 3/4” 1

15 50074138 Seal Kit 1

40-1-15


2

98

14

1213

46 7

3

12

5

10

11

9

8

15

1

916

HYDRAULIC CYLINDER - KICKER WHEELMonarch

(Replaces Bailey)




3 ------- Rod Cap 1

4 ------- Piston 1

5 ------- Rod, 1.125” Dia 1


7 ------- Tie Rod 4

8 ------- Pin, 1” Dia 2

9 ------- Cotter Pin, 3/16” x 1-1/2” 4

10 ------- Rod Clevis 1

11 ------- Bolt 1

12 ------- Hex Nut 8

13 ------- Hex Nut 1

14 ------- Plug, 3/4” 1

15 ------- Hex Nut 1

16 50079046 Seal Kit 1

40-1-16


2

98

14

1213

4

6 7

3

12

5

10119 8

15

1

HYDRAULIC CYLINDER - WING LIFT




3 ------- Rod Cap 1

4 ------- Piston 1

5 ------- Rod, 1.125” Dia 1


7 ------- Tie Rod 4

8 95425 Pin, 1” Dia 2

9 ------- Cotter Pin, 3/16” x 1-1/2” 4

10 50077191 Rod Clevis 1

11 ------- Set Screw 1

12 ------- Hex Nut 8

13 ------- Hex Nut 1

14 ------- Plug, 3/4” 1

15 50073528 Seal Kit 1

40-1-17


KICKER WHEEL KIT (OPTIONAL) - (Includes 50074130 Hyd. Kit)50074095

19

18

13

14

815

212

1411

7

754

4

7

9

6

1 10

13

13

3

16

17


1 50074105 Weldment, Kicker Main 1

2 50074113 Bracket, Kicker Slide 1

3 50074118 Carrier, Rake Wheel 1

4 50073061 Bushing, Rake Arm 2

5 20570 Flatwasher, 1-1/4” SAE 1

6 53065 Pin, Spirol 3/8” x 2-1/2” 1

7 449BH Fitting, Grease 1/4-28 UNF Str. 3


9 45196BH Capscrew, 1/2” x 4” Gr 5 2

10 45104 Locknut, 1/2” Gr C 2

11 50079045 Cylinder, Tie Rod, 2” Bore x 8” Stroke x 1.125” Rod 1

12 1273BH Pin, Presto 9 Ga x 3” D 1

13 50074125 Shackle, Anchor 3

14 50074127 Stay, Spring 2

15 50074128 Spring, Kicker 1

16 50074126 Turn Buckle (5/16” x 18”), 9” Closed x 4.5” Adjust. 1

17 50075555 Assembly, Rake Wheel - RH 1


50075253 Assembly, Rake Wheel - RH 1


18 45063 Flatwasher, 3/8” 6

19 45073 Hex Nut, 3/8” 6

20 ------- Hyd. Kit, Kicker Wheel (50074130) [Not Shown] 1

2

1

3

5

6

4

40-1-18


HYDRAULIC KIT, KICKER WHEEL50074130


1 25H46118 Hose Assembly, Hydraulic - 25” Lg 1

2 25H41146 Hose Assembly, Hydraulic - 31” Lg 1

3 50074133 Tee, Male Branch, 9/16”-18 MJIC x 9/16”-18 MJIC x 3/4”-16 MORB 1

4 50074134 Tee, Male Branch, 9/16”-18 MJIC x 9/16”-18 MJIC x 3/8” NPT 1

5 50074132 Valve, Hydraulic Ball 1

6 50074135 Adaptor, 3/4”-16 MORB x 3/8” NPT 1

BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL March, 2014

RAKE WHEEL & TIRE ASSEMBLY


1 50073077 Assembly, Rake Wheel & Tire 1

2 50073075 Rim, 15 x 5.0 BW Rolled 5-0.53” 1

3 50073076 Tire, ST205/75 D15 K550 6P TL 1

2

3

1

40-1-19


LED LIGHT KIT (REAR LIGHTS ONLY)50074720


50074720 LED Light Kit 11 50072057 Module, Enhance 1

2 50074721 Main Harness (7 Pin, 16’ Long) 1

3 50074725 Wishbone Harness (8’ Long) 2

4 50074723 Dual LED Ag Lamp, Left Side, Amber/Red 1

5 50074724 Dual LED Ag Lamp, Right Side, Red/Amber 1

6 50072062 Lens, Red Replacement 2

7 50072063 Lens, Amber Replacement 2

8 50072064 Cover, Black Replacement Lens 4

9 ------- Slt Pn Hd Mach Screw, #10 x 1” 2

10 17020600 Flatwasher, #10 3

11 44520BH Locknut, #10 2

12 44186BH Capscrew, 1/4” x 1” Gr. 5 8


14 15608 Locknut, 1/4” Gr. C 8

15 50074735 Clamp 4

40-1-20

7

815

1312

4 13

6

14

1

9

10

10

11

2

3

13

1215

8

7

5

6

13

14

Left Side

Right Side

Wiring Harnesses

40-1-21


REDUCED GROUND PRESSURE CAM KIT(For Earlier Models w/Too Much Ground Pressure)


50074277 Reduced Ground Pressure Cam Kit, Ø4.75” 1

1 50074273 Cam Assembly, Ø4.75”, RH 1

50074274 Cam Assembly, Ø4.75”, LH 1

2 ------- Down Pressure Cam, Ø4.75” 1

3 50073510 Decal, RH 1

50073509 Decal, LH 1

4 20327 Roll Pin, 3/8” x 2-1/2” 1

5 45325BH Roll Pin, 7/32” x 2-1/2” 1

2

3

45

1

40-1-22


GROUND PRESSURE CAM ASSEMBLY KIT w/DOWEL


50080677 Ground Pressure Cam Assembly Kit w/Dowel 1

1 50078206 Cam Assembly, RH 1

50078207 Cam Assembly, LH 1

2 ------- Down Pressure Cam, Dowel Pin 1

3 50073510 Decal, RH 1

50073509 Decal, LH 1

4 50078203 Dowel Pin, 3/8” x 2-1/2” 1

2

3

4

1

40-1-23


WING SET PLATE SLOTTED KIT(For Earlier Models Having Trouble Leveling Rake Arms)


1 50078622 Wing Set Plate Slotted Kit 1

2 50078204 Wing Set Plate Weldment, Slotted 2

3 50077995 Nord-Lock, 3/4” 2

2

3

1

Documents

Sec 40 BSR Series Rakes Layout 1 - Bush Hog · 2020-02-20 · MODELS BSR8, BSR10 & BSR12. 40-1-7 BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL August, 2018 Item Part No Description