SAFETY GUIDE · 2019-05-13 · 3-4 Drilling holes in shaped steel Drilling holes in steel Speedy, high precision hole drilling Speedy, high precision hole drilling 5 CONTENTS PORTABLE

JQA-2042 NITTO KOHKI CO.,LTD.Machine Tools Division

ISO 9001

JQA-EM4057NITTO KOHKI CO.,LTD.

HeadquartersResearch Center

ISO 14001

Cat.No. Tk103j

NITTO KOHKI CO.,LTD.

Safety Precautions

Be sure to read and understand all safety precautions mentioned below and to follow the instructions given to operate eachNitto Kohki brand tool as stated in the operator’s manual. Keep operators manual close by when operating machines or toolsfor reference of safe operation and precautions.

Failure to observe the following warnings may cause a potentially hazardous situation, which if not corrected could resultin serious injury or death. To prevent the risk of fire, electric shock, and/or personal injury, proper safety guidelines shouldbe followed at all times.

Warning for ALL Machines and Tools

Notice for Air ToolsNotice for Electric Tools• Air pressure at the inlet of the tool must not exceed 0.59 MPa (6 kgf/cm2).

SAFETY GUIDE

• Always keep the work area free from clutter and potentially dangerous conditions such as hanging power cords, working debris, air hoses, and garbage to prevent accidents from occurring.

• Consider proper working environments for each tool carefully. Do not expose tools to extreme amounts of moisture or direct contact with water or rain. Keep area well lit at all times to prevent hidden dangers and never operate the equipment near flammable liquids or in gaseous or explosive atmospheres.

• Keep all tools and tool accessories away from children and all unauthorized personnel. Serious injury or possible death may result from machines being handled by children.

• Properly store machines and accessories while not in use. They should be kept in a dry, locked-up location out of reach of children or unauthorized personnel.

• Improper or negligent use of tools will cause increased maintenance costs, and the amount of time in which to complete the job. Always let the tool do the work at the rate of which it was designed. Best performance is always achieved by reading and understanding the proper operation of each machine or tool.

• Always wear safety glasses and protective hand and foot wear during or around operating tools. Wear a protective hair covering to contain long hair. Do not wear loose clothing and/or accessories as they may be caught in moving parts and inflict serious injury or possible death.

• Wear respiratory protection when working in an environment where dust particles are generated during operation.

• Do not over-reach or allow yourself to become unstable during tool operation and always maintain a correct posture.

• Use clamps or a vise to secure the work piece tightly and eliminate vibration. Never hold the work piece with your hands, keep both hands on the tool for increased productivity.

• Use the right tool or machine that can complete the job within its specifications. Do not attempt to adapt smaller machines or tools to complete a job designed for heavy-duty equipment. Do not use the tools for other than what they were designed for. There is a right tool for each job, be aware of tool limitations and never overload.

• Make sure to inspect all external screws, nuts, bolts and attached accessories are fastened tightly and secure prior to each use. All moving parts should be free from obstruction and allowed to operate smoothly. Any damaged or missing parts should be repaired or replaced by the sales agent or distributor from which the tool was originally purchased. Do not use machines or tools which cannot be activated or stopped with a power switch or lever.

• The power source must be limited to the individual tools specifications as stated on the nameplate or instruction manual.

• Make sure that all machine and power tools are properly grounded at all times (excludes double-insulated tools). Always use a GFCI (Ground-Fault-Circuit-Interrupt) to protect the user and surrounding persons from electric shock.

• Be aware of low voltage situations. Improperly gauged extension cords or power cords used or shared with other electrical devices will cause all tools on the line to not run at optimal performance. This condition may result in damage to the machine and/or operator.

• Do not use any machine with a damaged, frayed, cut, or deteriorated power cords or air hoses. Always replace at the first sign of damage.

• Always remove all tools required to adjust, add, or remove parts from tools prior to use to prevent tool damage or user injury.

• Always avoid an unexpected start by having all power buttons or levers in the off position prior to attaching to a power or air supply. Never carry tools with your finger on the on/off switch or lever when the power or air supply is attached.

• Do not use the power or air supply lines to move, carry or support the tool during usage or transportation. Do not place the power or air line near a heat source, oil, water, or items with sharp edges.

• Never leave a machine or tool running unattended. Keep a firm grip on the designated areas of the machine or tool until it comes to a complete stop. Always turn the power switch or lever to the off position and disconnect from the power source when not in use.

• Do not disassemble or modify a tool to complete a job other than what it was designed for. This will void any warranty on the equipment and may cause serious personal injury or possible death.

• Maintenance is necessary for all machines and tools. Always maintain blades and cutters properly and replace when edges become damaged or are not sharp enough for safe operation. Follow the instruction manual for lubrication needs and adjustment points if applicable. Check the power and air supply lines periodically and change accordingly to safety regulations. If an extension line is adopted, always make sure that it meets or exceeds tool requirements for amperage or air supply before using and is rated for outdoor usage. Change supply lines whenever they are found to be defective or damaged. Keep the grip and handles dry and clean of grease or oil so that it will not disturb proper operation.

• Switch off and disconnect from power source before servicing equipment or changing accessories.

• Be alert and pay close attention to the work being performed at all times. Do not operate machines or tools when heavily fatigued. Users should be aware of all circumstances surrounding their application.

• Use only recommended parts and accessories as per individual machine or tool operator manuals. Use of improper accessories or attachments may result in serious injury or possible death.

• All repairs and services must be performed by authorized Nitto Kohki dealers or technicians.

• Do not deface or remove any label, warning indicator, or nameplate associated with each machine or tool.

1

Whether you just glance through this booklet or give it an intensive reading, we are sure you'll agree thatNITTO KOHKI's portable hydraulic and electric machines, couplers and pneumatic hand tools are amongthe finest precision engineered equipment to be found today.

PageManufacturing SteelFabricating

Welding Metal Casting &Forging

AUTOMOTIVE &SHIP BUILDING

Construction

3-4

Drilling holesin shapedsteel

Drillingholes in steel

Speedy, highprecisionhole drilling


5

CONTENTS

PORTABLE MAGNETIC BASE AUTOMATIC DRILLING MACHINE

ATRA ACEauto feed (WA-3500 / WA-5000)

BORING

11

On-sitepunchingholes onshaped steels

Punchingholes on shipframeworks

Punchingbolt holeson steelplates

Holepunching onsteel plates

PORTABLE DOUBLE-ACTING HYDRAULIC PUNCHER

SELFER ACEHS SERIES & HYDRAULIC PUMP

PUNCHING

12

On-sitepunchingholes onshaped steels

Punchingholes on shipframeworks

Punchingbolt holeson steelplates

Holepunching onsteel plates

PORTABLE SINGLE-ACTING HYDRAULIC PUNCHER

SELFERHA SERIES & HYDRAULIC PUMP

PUNCHING

13-14

On-sitesmall holepunching

Punchingholes onangles andchannels

Speedy, easyholepunching onsteel sheets

ELECTRICALLY OPERATED HYDRAULIC PUNCHER

HANDY SELFER ANDPUNCHES & DIES FOR SELFER

PUNCHING

15

Chamferingof colums

Chamferingof steel plates

Chamferingof largeworkpieces

PORTABLE CHAMFERING TOOLS

BEVELERHAND BEVELER

CHAMFERING

Chamferingof steel plate

15-16

Chamferingof steel plate

Chamferingof dies andmachine


CIRCUIT BEVELERCHAMFERING

Chamferingof cast molds

Surfacechamferingof pre-weldedshaped steelparts

15-16

Chamferingof steel plates

Chamferingof largeworkpieces


BEVELERMINI BEVELER

CHAMFERING

PORTABLE MAGNETIC BASE DRILLING MACHINE

ATRA ACEmanual feed (WOJ-3200 / W0-3200)

BORING

6

7

Drilling holesin shapedsteel

Drilling holesin steel




ATRA ACEmanual feed (AO-5575)

BORING


ATRA ACEquick auto & manual feed

BORING

9-10

Drilling oflarge andsmalldiameterholes in steel

Drilling holesDrilling holesin steel

Drilling oflarge andsmalldiameterholes in steel

ANNULAR CUTTERS

BROACH CUTTERS &BROACH HOLDERS

BORING

Home boringfor jigattachment

Initial boringfor sheetcutting bywelder

8

Bring ofshaped steel,drilling atelevated site

Variousboring

DrillingPrecisionboring offlanges

PORTABLE MAGNETIC DRILL STAND

ATRA MASTERBORING

Power Tools, delvo, Spring Balancer, Linear Motor Driven Free Piston System 17

CUPLA Series / Mini Cupla Super 18

2

Model WA-3500 Model WA-5000

High-performance mechanism & high-tech components

Mounting the cutter Removing the cutter

One-touch cutter replacementReplacement is quick and easy with ourunique push fit self-centeringcutter system.

Coolant into the Heart of the cutCoolant is fed directly to the inside of thecut. The coolant system also features anauto shut-off.

Fail-Safe ProtectionBuilt-in motion sensorIf any lateral movement or excess vibration is detected, both the drill andthe feed motor stop instantly. Nitto Kohki is the first company toincorporate this feature into magnetic base drills.

Fail-safe restartThe drill will not re-start even if power is re-supplied after accidentalshutdown. Drilling can only be continued after turning on the drill switch.

Magnet open-circuit sensorThe drill will not start until the magnetic field is active.

237 mm

425 mm

613 mm

409 mm

237 mm

535 mm

Max. plate thickness 75 mm

Portable Magnetic Base Automatic Drilling MachineATRA ACE auto

3

JETBROACH One-touch Type35L


HI-BROACH One-touch Type25L

TB01507Cutting Oil

2 L per can


TB01507Cutting Oil

2 L per can

On-site hole-cuttingOn-site hole-cutting in steel plates,H-Beams shapes, shaped bars,framework, and other machinery,shipbuilding, bridges and structures,etc. steel reinfocements andconstruction materials.

Rod handle

ON

New drill control prevents cutters from breaking

Standard Accessories

• Pilot Pin 08035 A2 : 1 pc.• Chain Ass'y : 1 set• Side Handle Ass'y : 1 set• 3 mm Hex Socket Screw Key : 1 pc.• 8 x 10 mm Spanner : 1 pc.• Cutting Oil 0.5 L : 1 can• Plastic Case : 1 pc. • Guard Ass'y : 1 set

• Pilot Pin 08050 A3 : 1 pc.• Chain Ass'y : 1 set• Side Handle Ass'y : 1 set• 3 mm / 4 mm Hex Socket Screw Key : each 1 pc.• 8 x 10 mm Spanner : 1 pc.• Cutting Oil 0.5 L : 1 can• Plastic Case : 1 pc. • Guard Ass'y : 1 set

Optional Accessories

Always use genuine Nitto Kohkicutters & coolant.

JETBROACH One-touch Type25L,35L,50L

HI-BROACH One-touch Type25L,50L

Always use genuine Nitto Kohkicutters & coolant.

Specifications

ElectricDrill

Cutter

Model

Power Source (Single Phase)

Rated Power Consumption W

Rated Current A

No Load Speed min-1 (rpm)

Magnet Power Consumption W

Hole-cutting Capacity

One-touch type JETBROACH 25L




One-touch type HI-BROACH 25L


Magnet Holding Power N (kgf)

Magnet Dimensions mm

Mass (Weight) kg

WA-3500

1,100

950

34

7,056 (720)

92 x 216

20

WA-5000

1,150

350 / 650

75

9,800 (1,000)

101 x 201

23

110 - 120 V AC, 50/60 Hz

10.2

Hole Diameter

-

17.5 to 35 mm

17.5 to 35 mm

-

14 to 35 mm

-

220 - 240 V AC, 50/60 Hz

5.1

Plate Thickness

-

9 to 35 mm

9 to 35 mm

-

9 to 25 mm

-

110 - 120 V AC, 50/60 Hz

10.8

Hole Diameter

12 to 17 mm

17.5 to 40 mm

12 to 50 mm

17.5 to 50 mm

14 to 50 mm

14 to 50 mm

220 - 240 V AC, 50/60 Hz

5.4

Plate Thickness

9 to 25 mm

9 to 35 mm

9 to 50 mm

9 to 75 mm

9 to 25 mm

9 to 50 mm

Slow start mechanismThe feed speed is reduced for the first few seconds after boringbegins to ensure a smooth cut through the mill scale.

Auto-feedAutomatic control & feed are activated by simplypushing the rod handle to engage the gears.

Load sensorThe dual sensing system responds toboth drilling and feeding forces on thecutter for the optimum cutting condition.

Variable speedThe feed speed is continuously monitored andupdated proportionally to the load on the cutter.

Cycle stopAfter the cut has finished, a detector responds to the reduction inload and both the drill and the feed motor automatically stop.

Overload stopWhen an excessive load is applied to the cutter, both the drill and thefeed motor will stop automatically to prevent the cutter from breaking.

Portable Magnetic Base Automatic Drilling MachineATRA ACE auto

4

Designd to use Jetbroach Carbide Tipped Annular Cutters

Designd to use High Speed Steel Annular Cutters

Portable Magnetic Base Drilling MachineATRA ACE WOJ-3200/WO-3200

Manual feed

WOJ-3200Manual feed

WOJ-3200

Manual feed WO-3200

Standard Accessories • Pilot Pin 08050 : 1 pc.• 3 mm Hex Socket Screw Key : 1 pc.• 8 x 10 mm Spanner : 1 pc.• Side Handle Assy’s : 1 set• Safety Strap : 1 pc.• Guard Ass'y : 1 set

Specifications

ElectricDrill

Cutter

Model


Rated Power Consumption　

Rated Current　

No Load Speed　

Magnet Power Consumption　


　

Magnet Holding Power　

Magnet Dimensions　

Mass (Weight)　

W

A

min-1 (rpm)

W

　

One-touch type HI-BROACH

kN (kgf)

mm

kg

WO-3200

220 - 240 V AC, 50/60 Hz

950

4.3

530

70

9 (918)

99 x 177

13

Hole Diameter

12 to 32 mm

Plate Thickness

9 to 50 mm

Standard Accessories • Pilot Pin 08050 : 1 pc.• 3 mm Hex Socket Screw Key : 1 pc.• 6 mm Hex Socket Screw Key : 1 pc.• 8 x 10 mm Spanner : 1 pc.• Safety Strap : 1 pc.• Sub Handle : 1 pc.• Guard Ass'y : 1 set

Specifications

ElectricDrill

Cutter

Model


Rated Power Consumption　

Rated Current　

No Load Speed　

Magnet Power Consumption　


　

Magnet Holding Power　

Magnet Dimensions　

Mass (Weight)　

W

A

min-1 (rpm)

W

　

One-touch type JETBROACH

kN (kgf)

mm

kg

WOJ-3200

220 - 240 V AC, 50/60 Hz

950

4.3

870

70

9 (918)

99 x 177

13

Hole Diameter

12 to 32 mm

Plate Thickness

9 to 50 mm

318 mm99 mm

361 mm

Reversible Feed HandlesFeed handles can be positioned on the rightor left hand side for ease of drilling and mounting in confined spaces.

Optional One-Touch AdapterOptional one-touch adapter allowsthe use of up to 13 mm twistdrills to be used in theoriginal arbor.

Optional Jet Oiling SystemOptional jet oiling system for use with all drilling applications and types of cutters to extend cutter life and increase hole output.

Optional Chip BreakerOptional chip breaker helps prevent the cutter from plugging the hole with chip debris, causing some false overloadsand cutter life loss.

Body Height Adjustment

60 mm

The world's first manual feed with ''Smart-Stop / Rapid-Restart'' technology for WOJ-3200 / AO-5575

This new feature is a breakthrough in the Manual drill industry. Formerly only found on high end Nitto Kohki Automatic drills, this technology displays the current drill status via the LED Load Indicator. Customers will experience a cutting edge drill management system designed solely around saving time and money in replacement parts and cutters in addition to reducing user fatigue and downtime.

Model WOJ-3200 Model AO-5575

LoadIndicator

361 mm

Loosening the pillar clamp allows thecomplete frame to be lifted up to a maximum of 60 mm for specific drilling. The use of Hi-Broach cutters require the frame to be at the lowest position, while twist bit drilling required the appropriate amount of elevation to be adjusted for safe operation. The pillar clamp is required to be tightened before safe drilling may take place. Note: Always engage the magnet before adjusting the body height.

Newly developed Over-Load Shutdown, Magnet Open-Circuit Sensor, and Fail-Safe Restart technology formerly only found on high-end Nitto Automatics are incorporated on the machine.(Smart-Stop / Rapid-Restart feature is not included.)

318 mm99 mm

5

Portable Magnetic Base Drilling MachineATRA ACE WOJ-3200/AO-5575

Manual feed

AO-5575Manual feed

AO-5575

Standard Accessories• Pilot Pin 08050 A3 : 1 pc.• Chain Ass'y : 1 set• Side Handle Ass'y : 1 set

• 3 mm Hex Socket Screw Key : 1 pc.• 5 mm Hex Socket Screw Key : 1 pc.• 8 x 10 mm Spanner : 1 pc.

• Cutting Oil 0.5 L : 1 can• Guard Ass'y : 1 set

Optional Accessories

Specifications

ElectricDrill

Cutter

Model



Rated Current A




One-touch type JETBROACH

One-touch type HI-BROACH

Magnet Holding Power kN (kgf)


Mass (Weight) kg

AO-5575

220 - 240 V AC, 50/60 Hz

1,150

5.4

350 / 650

50

10 (1,020)

86 x 170

18

Hole Diameter

12 to 55 mm

12 to 50 mm

Plate Thickness

9 to 75 mm

9 to 50 mm

296 mm86 mm

611 mm

"Smart Stop"Fast Blinking Red

Slow Blinking Green

Green / Orange

RedOrangeGreen

Resume proper load

“Smart Stop” stalls motor when overloaded.

Proper load

LED load indicator

Overload

“Rapid-Start” resumes drilling operation

Drill motor shuts off

Drill motor will not turn on

Continued overload

Slow Blinking Red

Magnet malfunction

Load detector with “Smart-Stop/Rapid-Restart” technology

"SmFast



Safety mode

As the drilling load increases, the load indicator will change in color from green to orange to red. In addition, if excessive feeding force is applied, the load indicator will rapidly blink red and the rotation of the drill motor will slow down and temporarily stop. If the load is released while the load indicator is blinking red, the drill motor will resume its rotation.

Designd to use Jetbroach and Hi-broach Annular Cutters

HI-BROACH One-touch Type25 mm, 50 mm

JETBROACH One-touch Type25 mm, 35 mm,50 mm, 75 mm

TB01507Cutting Oil

2 L per canAlways use genuine NittoKohki cutters & coolant.

Low Speed

Optional Chip BreakerThis chip breaker prevents the cutter from becomingjammed with metal shavings.

Hi Speed

Coolant ValveAdjustable coolant flowdelivered to the centerof the cutter.

Speed selection (Change gear)

Reversible feed handle

Model AO-5575

MAX. 55 mm dia. x 75 mm deepLIGHT WEIGHT 18 kg

Built-in coolanttank preventsdamage

One-touch cutter replacementOur original self-centering tool-less chuck is quick and easyto change cutters with little downtime. (WOJ-3200)

Mounting the cutter Removing the cutter Mounting the twist drill

6

Specifications

ElectricDrill

Cutter

Model



Rated Current A






Side-Lock type JETBROACH 75L




Mass (Weight) kg

QA-4000

680

750

50

6,664 (680)

82 x 172

18.5

QA-6500

220 - 240 V AC, 50/60 Hz

1,010

4.5

400 / 750

75

9,800 (1,000)

100 x 200

26

115 V AC, 50/60 Hz

6.1

Hole Diameter

17.5 to 40 mm

-

-

14 to 15 mm

16 to 18 mm

220 - 240 V AC, 50/60 Hz

3.0

Plate Thickness

9 to 35 mm

-

-

9 to 12 mm

9 to 25 mm

Hole Diameter

17.5 to 40 mm

17.5 to 65 mm

-

18 to 35 mm

-

Plate Thickness

9 to 35 mm

9 to 50 mm

-

9 to 25 mm

-

A-100

220 - 240 V AC, 50/60 Hz

1,600

7.4

330

80

17,640 (1,800)

130 x 256

50

Hole Diameter

-

-

50 to 100 mm

-

-

Plate Thickness

-

-

13 to 75 mm

-

-


• Pilot Pin 08035 A2 : 1 pc. • Chain : 1 pc• 3 mm Hex Socket Screw Key : 1 pc.• 4 mm Hex Socket Screw Key : 1 pc.• 8 x 10 mm Spanner : 1 pc.• Cutting Oil 0.5 L : 1 can • Tool box : 1 pc.• Side Handle : 1 pc. • Oil Tank Ass'y : 1 set.

• Pilot Pin 08050 A3 : 1 pc. • Chain : 1 pc.• 3 mm Hex Socket Screw Key : 1 pc.• 4 mm Hex Socket Screw Key : 1 pc.• 8 x 10 mm Spanner : 1 pc.• Cutting Oil 0.5 L : 1 can • Tool box : 1 pc.• Chip Stopper : 1 pc. • Side Handle : 1 pc.• Oil Tank Ass'y : 1 set.

Nitto Kohki's Atra Ace boosts productivity in the holedrilling industry

One-touch Cutter Replacement

Max. Hole-cutting Capacity : 40 mm dia.Max. Plate Thickness : 35 mm


One-touch Cutter Replacement Side-lock Type Cutter


Self Feeding and Automatic Return

Load Detection

Built-in Motion Sensor

Automatic Step Feed

Restart Prevention

575 mm

318 mm 705 mm

73.5 mm

Portable Magnetic Base Drilling MachineATRA ACE quick auto & manual feed

• Pilot Pin 12075 : 1 pc. • Chain : 1 pc• 2 mm / 2.5 mm / 3 mm / 4 mm / 5 mm / 6 mm / 8 mm Hex Socket Screw Key : each 1 pc.• 7 x 8 mm Spanner : 1 pc.• Cutting Oil 0.5 L : 1 can • Tool box : 1 pc.• Oil Cap Ass'y : 1 set. • Rod Handle : 3 pcs.

535 mm

215 mm454.5 mm

49 mm

425 mm

215 mm 407 mm

49.5 mm

Built-in Motion Sensor

Self Feeding and Automatic Return

Load Detection

7

ATRA MASTER can mount on many drills in the market. The magnet bases of ATRA MASTER hold the drills perpendicular to steel plates even on non horizontal places.

Standard accessories

• 5 mm Hex. Socket Screw Key : 1 pc.• 2.5 mm Hex. Socket Screw Key : 1 pc.• 7 x 8 mm Spanner : 1 pc.• Retaining Bush E TP12556 : 1 pc.• Rod Handle : 2 pcs.

• 35 x 41 mm Spanner : 1 pc.• 6 mm Hex. Socket Screw Key : 1 pc.• 2.5 mm Hex. Socket Screw Key : 1 pc.• 7 x 8 mm Spanner : 1 pc.• Fixing A Ass'y TA99742 : 1 set• Chain : 1 pc.• Rod Handle : 3 pcs.

• 35 x 41 mm Spanner : 1 pc.• 6 mm Hex. Socket Screw Key : 1 pc.• 2.5 mm Hex. Socket Screw Key : 1 pc.• 7 x 8 mm Spanner : 1 pc.• Fixing D Ass'y TA99750 : 1 set• Chain : 1 pc.• Rod Handle : 3 pcs.

• 35 x 41 mm Spanner : 1 pc.• 6 mm Hex. Socket Screw Key : 1 pc.• 2.5 mm Hex. Socket Screw Key : 1 pc.• 7 x 8 mm Spanner : 1 pc.• Fixing D Ass'y TA99750 : 1 set• Chain : 1 pc.• Rod Handle : 3 pcs.

273 mm

236 mm

SpecificationsModel



Drilling Capacity (diameter) mm


Maximum Stroke mm


Height mm

Mass (Weight) kg

M-100

220 - 240 V AC, 50/60 Hz

35

10

3,430 (350)

100

105 dia.

273

6.2

M-130A

220 - 240 V AC, 50/60 Hz

35

13

5,880 (600)

175

141 dia.

397

16

M-250B

220 - 240 V AC, 50/60 Hz

80

25

14,700 (1,500)

230

110 x 243

528

25.5

M-320

220 - 240 V AC, 50/60 Hz

80

32

17,640 (1,800)

280

124 x 244

525

29

N.B. : The electric drill and drill mount fixture for it do not come with ATRA MASTER's.

Drilling Capacity : 10 mm

Max. Stroke : 100 mm

Mass (weight) : 6.2 kg

397 mm

377 mm



Mass (weight) : 16 kg

528 mm

461 mm



Mass (weight) : 25.5 kg

525 mm

514 mm



Mass (weight) : 29 kg

Swivel Angle Front and Rear Movement

28 mm330° 28 mm330° 20 mm

50°

Portable Magnetic Drill StandATRA MASTER

8

12131415161717.5181919.5202121.52222.52323.52424.525262728293031323334353637383940414243444546474849505152

25mm

mm50

TK00698TK00699TK00700TK00701TK00702TK00703TK00335TK00336TK00337TK00338TK00339TK00340TK00341TK00342TK00343TK00344TK00345TK00346TK00347TK00348TK00349TK00351TK00352TK00353TK00354TK00355TK00356TK00357TK00359TK00361TK00704TK00705TK00706TK00707TK00708TK00709TK00710TK00711TK00712TK00713TK00714TK00715TK00716TK00717TK00718TK00719TK00720

•••••••••••••••••••••••••••

••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••••••••••••••

••••••

•••••••••••••••••••••••

•••••••••••••••••••••••••••••••••••••••••••••

Depth PN WO

-320

0

AO-5

575

WA-

3500

WA-

5000

QA-

4000

QA-

6500

HI-BROACH

mmdia.

1213141516171819202122232425262728293031323334353637383940414243444546474849505152

TK00721TK00722TK00723TK00724TK00725TK00726TK00727TK00728TK00729TK00730TK00731TK00732TK00733TK00734TK00735TK00736TK00737TK00738TK00739TK00740TK00741TK00742TK00743TK00744TK00745TK00746TK00747TK00748TK00749TK00750TK00751TK00752TK00753TK00754TK00755TK00756TK00757TK00758TK00759TK00760TK00761

•••••••••••••••••••••

•••••••••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••••••••••

Depth PN WO

-320

0

AO-5

575

WA-

5000

mmdia.BROACH CUTTERS are far better than twist drills:

• No dead point• Peripheral cutting• Blade cutting resistance reduced by 50 %• Available diameter size: 12 - 100 mm

Test Drilling is very often the only way todetermine the machinability of difficultmaterials. Use a small size cutterwherever possible in order tominimize trial costs.

Industrial cutters for faster and better finished holes.• The Spring-loaded pilot pin picks up the hole location quickly, and ejects the slug automatically at the end of cut• Available with No. 2 - 4 Morse taper shanks• Oil cup complete Ass'y (PN TB00350) is available as an optional attachment which provides continuous and adjustable cutting oil flow to the cutting area

Morse Taper No.

M.T.No.2

M.T.No.3

M.T.No.4

BHM-02035TB00390

163 mm

BHM-03050TB00392

BHM-13075 TB00352

BHM-14075TB00354

Model Cutter

HBO-25L12-17 dia.

Optional

Optional

Optional

Standard

Standard

Standard

06025 (PN TK01167)

08025 (PN TJ12696)

08035 (PN TJ15859)

17.5-35 dia.

17.5-35 dia.

12-17 dia.

17.5-52 dia.

12-17 dia.

18-52 dia.

17.5-40 dia.

17.5-65 dia.18-35 dia.

06025 (PN TK01167)

08025 (PN TJ12696)

06050 (PN TK01166)

0850 (PN TK00802)

08050 (PN TJ16019)

08035 (PN TJ15859)

08050 (PN TJ16019)

JBO-35L

HBO-25L

HBO-50L

JBO-35L

JBO-50LJBO-50L(W)

JBS-75L 50-100 dia.12075

(PN TA9A207)

Cutter Diameter Pilot Pin Accessory

65 mm(12 - 19.5 dia.)

58 mm(20 - 52 dia.)

65 mm(25L)73 mm(35L)

95 mm(12-17x50L)90 mm(17.5-65x50L)

For stacked two plates.

156 mm

Hole-cuttingCapacity

Feed Speed mm/revCircumferential Speed m/min

HI-BROACHOne-touch Type / 25L

25L : 12 - 52 dia.---

25L : 25---

86 mm

HI-BROACHOne-touch Type / 50L

--

50L : 12 - 52 dia.---

50L : 50-

JETBROACHOne-touch Type / 25,35,50L

JETBROACHOne-touch Type / 50L(W)

25L : 2535L : 3550L : 50-

--

50L(W) : 18,22,24 - 26.5,28,32, and 35 dia.

- -

50L(W) : 50-

JETBROACHOne-touch Type / 75L

--

75L : 17.5 - 55 dia.----

75L : 75

JETBROACHSide lock Type / 75L

--

75L : 50 - 100 dia.----

75L : 75

117 mm90 mm

25L : 12 - 17 dia.35L : 17.5 - 40 dia.50L : 12 - 65 dia.

-

182 mm

248 mm

232 mm

One-touch TypeHI-BROACH

One-touch Type

Hole Diameter mm

Plate Thikness mm

0.02 - 0.115 - 35 (mild steel) 35 - 50 (mild steel)

9

JETBROACH CUTTERS & HI-BROACH CUTTERS

Combination of Pilot Pins & Broach Cutters

12075 PN : TA9A207 JBS 50 - 100 dia.Depth 75 mm

192 mm

08035 PN : TJ15859 JBO 17.5 - 40 dia.Depth 35 mm

91 mm8 dia.

08050 PN : TJ16019

112 mm8 dia.

6dia.

Annular CuttersJETBROACH CUTTERS & HI-BROACH CUTTERS

HBO 12 - 17 dia.Depth 25 mm

HBO 17.5 - 52 dia.Depth 25 mm

06025 PN : TK01167

08025 PN : TJ12696

Pilot Pin HI-BROACH Cutters Pilot Pin JETBROACH Cutters

Pilot Pin JETBROACH Cutters

81 mm

5 dia.

8 dia.76 mm



06050 PN : TK01166

0850 PN : TK00802

5dia.6.35 dia.

6.35 dia. 6.35 dia.

112 mm

06050 PN : TK01166

5dia.6.35 dia.

112 mm

7 dia.8 dia.

100 mm

JBO 12 - 17 dia.Depth 25 mm

JBO 12 - 17 dia.Depth 50 mm

06025 PN : TK01167

81 mm

5 dia.

JBO 17.5 - 65 dia.Depth 50 mm

08075 PN : TJ17436

133 mm

JBO(W) 18 - 35dia.Depth 50 mm for stacked two (=W) plates.

JBO 17.5 - 55 dia.Depth 75 mm

08050 PN : TJ16019

112 mm8 dia.

8 dia.

Pilot Pin JETBROACH Cutters

JETBROACH

One-touch Type

10

12131415161717.5181919.52020.52121.52222.52323.52424.5252626.5272829303132333435363738394041424344454647484950515253545556575859606162636465

TK01154TK01155TK01156TK01157TK01158TK01159TK00380TK00381TK00382TK00383TK00384TK00385TK00386TK00387TK00388TK00389TK00390TK00391TK00392TK00393TK00394TK00395TK00396TK00397TK00398TK00399TK00400TK00401TK00402TK00403TK00404TK00405TK00406TK00407TK00408TK00409TK00410TK00411TK00412TK00413TK00414TK00415TK00416TK00417TK00418TK00419TK00420TK00442TK00443TK00444TK00445TK00446TK00447TK00448TK00449TK00450TK00451TK00607TK00608TK00609TK00610TK00611

•••••••••••••••••••••••••••••

••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••••••••••••••••••

••••••••••••••••••••••••••••••••••••••••••••••••••••••••

••••••••••••••••••••••••••••••••••••••••••••••••••••

Depth PN WO

J-32

00

AO-5

575

WA-

3500

WA-

5000

QA-

6500

mmdia.

17.51819202122232425262728293031323334353637383940414243444546474849505152535455

TK01036TK01003TK01004TK01005TK01006TK01007TK01008TK01009TK01010TK01011TK01012TK01013TK01014TK01015TK01016TK01017TK01018TK01019TK01020TK01021TK01022TK01023TK01024TK01025TK01026TK01027TK01028TK01029TK01030TK01031TK01032TK01033TK01034TK01035TK01112TK01113TK01114TK01115TK01116

•••••••••••••••••••••••••••••••••••••••

••••••••••••••••••••••••••••••••••

Depth PN AO-5

575

WA-

5000

mmdia.

5051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100

TJ17709TJ16651TJ16652TJ16653TJ16654TJ16655TJ16656TJ16657TJ16658TJ16659TJ16660TJ16661TJ16662TJ16663TJ16664TJ16665TJ16666TJ16667TJ16668TJ16669TJ16670TJ16671TJ16672TJ16673TJ16674TJ16675TJ16676TJ16677TJ16678TJ16679TJ16680TJ16681TJ16682TJ16683TJ16684TJ16685TJ16686TJ16687TJ16688TJ16689TJ16690TJ16691TJ16692TJ16693TJ16694TJ16695TJ16696TJ16697TJ16698TJ16699TJ16700

•••••••••••••••••••••••••••••••••••••••••••••••••••

Depth PN A-10

0

mmdia.

12131415161717.5181919.52020.52121.52222.52323.52424.5252626.52728293031323334353637383940

TK01148TK01149TK01150TK01151TK01152TK01153TK00301TK00302TK00304TK00305TK00306TK00307TK00308TK00309TK00310TK00311TK00312TK00313TK00314TK00315TK00316TK00317TK00318TK00319TK00320TK00321TK00322TK00323TK00324TK00325TK00326TK00328TK00602TK00603TK00604TK00605TK00606

•••••••••••••••••••••••••••••

••••••••••••••••••••••••••

18222424.5252626.5283235

TK01068TK00622TK00623TK00631TK00624TK00625TK00632TK00626TK00627TK00628

••••••••••

••••••••••

Depth PN WO

J-32

00

AO-5

575

WA-

3500

WA-

5000

QA-

4000

QA-

6500

mmdia.

•••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••••••••

Depth PN

WO

J-32

00

AO-5

575

mmdia.

25

35

50

75

75

mm

mm

50mm

JETBROACH

One-touch Type

18222424.5252626.5283235


••••••••••

••••••••••

•••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••••••••

Depth PN

WO

J-32

00

AO-5

575

mmdia.

50mm

JETBROACH One-touch Type

18222424.5252626.5283235


••••••••••

••••••••••

•••••••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••

•••••••••••••••••••••••••••••••••••••

Depth PN WO

J-32

00

AO-5

575

mmdia.

50L for stacked two(=W) plates.

50mm

mm

mm

mm




JETBROACH Side-lock Type

Max. Punching Thickness : 13 mm

Max. Punching Diameter : 22 mm

Max. Throat Depth : 60 mm

New design adopted for punching stainless steel.Inching function (manual operation) is available.

SpecificationsModel


Max. Output Pressure MPa (kgf/cm2)

Output

At No Load L/min

At 68.65 MPa L/min

Motor

Reservoir Capacity L

Discharge Port

Electro-Magnetic Valve

Mass (Weight) kg

HPD-05

115 V / 230 V AC

68.65 (700)

0.4 kW 4P

4.0

Rc 3/8

4 way 3 position valve

32.5

50 Hz

1.20

0.55

60 Hz

1.44

0.66


• Hose Kit Ass'y : 1 set • Hose Cord Ass'y : 1 set• 4 mm / 5 mm Hex. Socket Screw Key : Each 1 pc.• Spanner : 1 pc. • Spanner 12 : 1 pc.• Sub Handle Ass'y : 1 set• Chip Guard Ass'y : 1 set • Tool Box : 1 pc.• D Punch / Die 22 mounted on machine



PNTB02506TP05184TB02390TP05777

Part NameHose Kit Ass'y 5 mUltra-high pressure hose 5 mSwitch Cord Ass'y 5 mUltra-high pressure hose 10 m

Unit1 set1 pc.1 set1 pc.

Model

HS series

PNTB02545TB02141TA92729TB02142

Part NameSwitch Cord Ass'y 10 mFoot Switch Ass'yOil Can Ass'yHook Clamp Ass'y

Unit1 set1 set1 set1 set

Model

HS seriesOptional Parts

323 mm

423 mm

for SELFER ACE

415 mm

426.4 mm




363 mm

430.5 mm




385 mm

462.5 mm

Double-Acting

24 mm

Dimension fromedge to PunchCenter

HS06, HS07, HS11

SpecificationsModel

Max. Throat Depth mm

Punching Capacity

Max. Punching Thickness mm

Max. Punching Diameter mm

Hole Making Time

Allowable Max. Pressure MPa (kgf/cm2)

Max.Output kN (tf)

Ram Stroke mm

Mass (Weight) kg

HS06-1322

60

Punching Time 7.9 sec.

Returning Time 3.4 sec.

68.65 (700)

367 (37)

21

20.5

for Mild Steel

13

22

for Stainless Steel

6

22

HS07-1624

70



68.65 (700)

464 (47)

25

25.5

for Mild Steel

16

24

for Stainless Steel

6

24

HS11-1624

110



68.65 (700)

464 (47)

25

30

for Mild Steel

16

24

for Stainless Steel

6

24

In case of mild steel maximum punching thickness must be decided based on the equation of 0.8 x punching diameter. For details see the instruction manual.

Portable Double-Acting Hydraulic PuncherSELFER ACE

11

Single-Acting




Punch, return, and reset operations are fully automatic.An emergency switch stops the punch instantly at any time.

SpecificationsModel


Max. Output Pressure MPa (kgf/cm2)

Output

At No Load L/min

At 68.65 MPa L/min

Motor

Reservoir Capacity L

Discharge Port

Mass (Weight) kg

SC-05

115 V / 230 V AC

68.65 (700)

0.4 kW 4P

4.0

Rc 3/8

27.5

50 Hz

1.20

0.55

60 Hz

1.44

0.66

381 mm

524.1 mm

324 mm

380 mm




418 mm

545.6 mm




436 mm

545.6 mm

24 mm

Dimentionfrom edgeto punch center

HA06, HA07,HA11


• Sub Handle Ass'y : 1 set• Hose Cord Ass'y : 1 set• 4 mm Hex. Socket Screw Key : 1 pc.• Spanner : 1 pc.• Tool box : 1 pc.• D Punch / Die 22 mounted on machine



SpecificationsModel


Punching Capacity



Hole Making Time

Allowable Max. Pressure MPa (kgf/cm2)

Max.Output kN (tf)

Ram Stroke mm

Mass (Weight) kg

HA06-1322

60

for Mild Steel

13

22

10.5 sec.

68.65 (700)

304 (31)

21

21.5

HA07-1624

70

for Mild Steel

16

24

16.5 sec.

68.65 (700)

431 (44)

25

28.5

HA11-1624

110

for Mild Steel

16

24

16.5 sec.

68.65 (700)

431 (44)

25

35.5

In case of mild steel maximum punching thickness must be decided based on the equation of 0.8 x punching diameter. For details see the instruction manual.

PNTA96534TP05184TA93778TA9B044TP05777

Part NameHose Kit Ass'y 5 mUltra-high pressure hose 5 mSwitch Cord Ass'y 5 mHose Kit Ass'y 10 mUltra-high pressure hose 10 m

Unit1 set1 pc.1 set1 set1 pc.

Model

HA series

PNTA95307TA94386TA92729

TA96342

Part NameSwitch Cord Ass'y 10 mFoot Switch Ass'yOil Can Ass'y

Hook Clamp Ass'y

Unit1 set1 set1 set

1 set

Model

HA series

HA07-1624HA11-1624

Optional Parts

Portable Single-Acting Hydraulic PuncherSELFER HA Type

12

Built-in hydraulic pump shows its power in making roundor elongated holes in flat bar, angle bar or channel iron

SpecificationsModel



Rated Current A




Punching Time sec (single pass)

Power Cord m

Mass (Weight) kg

E25-0615

220 - 240 V AC, 50/60 Hz

305

1.6

15

6

25

4

2.4

7.0

Motor

E55-0619

19

6

55

2

2.4

14

115 V AC, 50/60 Hz

670

6.0

220 - 240 V AC, 50/60 Hz

670

3.0


• E Punch 15 : 1 pc.• E Die 15A : 1 pc.• E Die 15B : 1 pc.• Spanner 8 : 1 pc.• 10 x 12 mm Spanner : 1 pc.• 2.5 mm Hex. Socket Screw Key : 1 pc.• 4 mm Hex. Socket Screw Key : 1 pc.• Auxiliary Oil : 1 pc.

• EL Punch 18 : 1 pc.• EL Die 18A : 1 pc.• EL Die 18B : 1 pc.• Spanner 10 x 12 mm : 1 pc.• 3 mm Hex. Socket Screw Key : 1 pc.• 4 mm Hex. Socket Screw Key : 1 pc.• 5 mm Hex. Socket Screw Key : 1 pc.• Stand Ass’y : 1set• Auxiliary Oil : 1 pc.

Optional AccessoryPN

TB00800

Part Name

Stand Ass'y

Sales Unit

1 set

Application

For thin sheets

For thick sheets

For thin sheets

For thick sheets

For channel iron

Type of Die

A

B

A

B

C

Model

E25-0615

E55-0619

Plate Thickness (mm)

Mild Steel

2 - 3.2

4 - 6

2 - 3.2

4 - 6

7 - 8

Stainless Steel

Max. 3

Max. 4

Max. 3

Max. 4

-

Selection of Dies

A= 7

5~12

5

t=Plate thickness

B=40~65

t1 B-t12

Punching Capacity in channel iron (E55-0619)

10 OD 11 OD 12 OD 13 OD 14 OD 15 OD 16 OD

75 x 40 t7

100 x 50 t7.5

125 x 65 t8

Punching Dia.

Size

Max.Punching Thickness : 6mm

Max.Punching Diameter : 15 mm

Max.Throat Depth : 25 mm

340.5 mm

357 mm

Max.Punching Thickness : 6mm

Max.Punching Diameter : 19 mm

Max.Throat Depth : 55 mm

420 mm

368 mm

Electrically Operated Hydraulic PuncherHANDY SELFER

13

Elongatedhole Punch

Roll Pin

Jig

Elongatedhole Die

Punches & Dies for SELFER Puncher

FOR HS06-1624/HS07-1624/HS11-1624/HA06-1624/HA07-1624/HA11-1624

PNTJ10778TJ11088TJ06700TJ06698TJ06696TJ06694TJ06692TJ06611TJ06690TJ06688TJ06686TJ06609TJ06684TJ06682TJ06680TJ06607TJ06678TJ07979TJ06676TJ06674TJ06566TJ07748TJ10061

Round hole D Punch

SizeD Punch 8D Punch 9D Punch 10D Punch 11D Punch 12D Punch 13D Punch 14D Punch 14.5D Punch 15D Punch 16D Punch 17D Punch 17.5D Punch 18D Punch 19D Punch 20D Punch 20.5D Punch 21D Punch 21.5D Punch 22D Punch 23D Punch 23.5D Punch 24D Punch 25

PNTK00242TK00243TK00244TK00245TK00246TK00247TK00248TK00249TK00250TK00251TK00252TK00253

Elongated hole E Punch

SizeEL Punch 10 x 6.5EL Punch 13 x 6.5EL Punch 13 x 8.5EL Punch 13.5 x 9EL Punch 15 x 10EL Punch 16.5 x 11EL Punch 17 x 8.5EL Punch 18 x 9EL Punch 18 x 12EL Punch 19.5 x 13EL Punch 20 x 10EL Punch 21 x 14


Elongated hole E Die(Type A for thin sheets)

SizeEL Die 10 x 6.5AEL Die 13 x 6.5AEL Die 13 x 8.5AEL Die 13.5 x 9AEL Die 15 x 10AEL Die 16.5 x 11AEL Die 17 x 8.5AEL Die 18 x 9AEL Die 18 x 12AEL Die 19.5 x 13AEL Die 20 x 10AEL Die 21 x 14A


Elongated hole E Die(Type B for thick sheets)

SizeEL Die 10 x 6.5BEL Die 13 x 6.5BEL Die 13 x 8.5BEL Die 13.5 x 9BEL Die 15 x 10BEL Die 16.5 x 11BEL Die 17 x 8.5BEL Die 18 x 9BEL Die 18 x 12BEL Die 19.5 x 13BEL Die 20 x 10BEL Die 21 x 14B

PNTJ10779TJ11089TJ06701TJ06699TJ06697TJ06695TJ06693TJ06612TJ06691TJ06689TJ06687TJ06610TJ06685TJ06683TJ06681TJ06608TJ06679TJ07980TJ06677TJ06675TJ06569TJ07749TJ10062

Round hole D Die

SizeD Die 8D Die 9D Die 10D Die 11D Die 12D Die 13D Die 14D Die 14.5D Die 15D Die 16D Die 17D Die 17.5D Die 18D Die 19D Die 20D Die 20.5D Die 21D Die 21.5D Die 22D Die 23D Die 23.5D Die 24D Die 25

•TA99037 Lock Nut Ass'y is reguired for D Punch 25

30

60

D Punch

42

16.5

D Dies

FOR E25-0615

PNTK00100TK00102TK00143TK00105TK00146TK00111TK00149TK00117TK00120TK00123TK00097TK00167TK00428

Round hole E Punch

SizeE Punch 4E Punch 5E Punch 5.5E Punch 6E Punch 6.5E Punch 8E Punch 8.5E Punch 10E Punch 11E Punch 12E Punch 13E Punch 14E Punch 15

PNTK00101TK00103TK00144TK00106TK00147TK00112TK00150TK00118TK00121TK00124TK00098TK00168TK00288

Round hole E Die(Type A for thin sheets)

SizeE Die 4AE Die 5AE Die 5.5AE Die 6AE Die 6.5AE Die 8AE Die 8.5AE Die 10AE Die 11AE Die 12AE Die 13AE Die 14AE Die 15A

PN-

TK00104TK00145TK00107TK00148TK00113TK00151TK00119TK00122TK00125TK00099TK00169TK00429

E Die(Type B for thick sheets)

Size -E Die 5BE Die 5.5BE Die 6BE Die 6.5BE Die 8BE Die 8.5BE Die 10BE Die 11BE Die 12BE Die 13BE Die 14BE Die 15B

PNTK00126TK00158TK00129TK00152TK00155

Elongated hole E Punch

SizeE Punch 10 x 5E Punch 10 x 6.5E Punch 12 x 6E Punch 13 x 6.5E Punch 13 x 8.5

PNTK00127TK00159TK00130TK00153TK00156


SizeE Die 10 x 5AE Die 10 x 6.5AE Die 12 x 6AE Die 13 x 6.5AE Die 13 x 8.5A

PNTK00128TK00160TK00131TK00154TK00157


SizeE Die 10 x 5BE Die 10 x 6.5BE Die 12 x 6BE Die 13 x 6.5BE Die 13 x 8.5B

16

30.5

E Punches

35

Front view ofE Dies Type A

35

Front view ofE Dies Type B

24

Side face ofE Dies Type A

21 : over or equal 8 dia.(19 : under 8 dia.)

27

Side face ofE Dies Type B

21 : over or equal 8 dia.(19 : under 8 dia.)

FOR E55-0619

PNTJ13229TJ13230TJ13231TJ13232TJ13233TJ13234TJ13235TJ13236TJ13237

Elongated hole D Punch

SizeD Punch 16 x 8D Punch 18 x 9D Punch 20 x 10D Punch 22 x 11D Punch 24 x 12D Punch 25 x 9D Punch 25 x 12D Punch 25 x 14D Punch 25 x 18

PNTJ13238TJ13239TJ13240TJ13241TJ13242TJ13243TJ13244TJ13245TJ13246

Elongated hole D Die

SizeD Die 16 x 8D Die 18 x 9D Die 20 x 10D Die 22 x 11D Die 24 x 12D Die 25 x 9D Die 25 x 12D Die 25 x 14D Die 25 x 18

PNTK00455TK00456TK00457TK00458TK00459TK00460TK00461TK00462TK00463

Elongated hole Jig

SizeJig 16 x 8Jig 18 x 9Jig 20 x 10Jig 22 x 11Jig 24 x 12Jig 25 x 9Jig 25 x 12Jig 25 x 14Jig 25 x 18

FOR HS06-1624/HS07-1624/HS11-1624/HA06-1624/HA07-1624/HA11-1624 Optional•TA99037 Lock Nut Ass'y is reguired for Elongated hole D Punch 25 x 9/12/14/18

PNTK00193TK00194TK00195TK00196TK00197TK00198TK00199TK00200TK00201TK00202TK00203TK00204TK00205TK00278TK00180

Round hole EL Punch

SizeEL Punch 6EL Punch 6.5EL Punch 8EL Punch 8.5EL Punch 10EL Punch 11EL Punch 12EL Punch 13EL Punch 14EL Punch 15EL Punch 16EL Punch 17EL Punch 18EL Punch 18.5EL Punch 19


Round hole EL Die(Type A for thin sheets)

SizeEL Die 6AEL Die 6.5AEL Die 8AEL Die 8.5AEL Die 10AEL Die 11AEL Die 12AEL Die 13AEL Die 14AEL Die 15AEL Die 16AEL Die 17AEL Die 18AEL Die 18.5AEL Die 19A


Round hole EL Die(Type B for thick sheets)

SizeEL Die 6BEL Die 6.5BEL Die 8BEL Die 8.5BEL Die 10BEL Die 11BEL Die 12BEL Die 13BEL Die 14BEL Die 15BEL Die 16BEL Die 17BEL Die 18BEL Die 18.5BEL Die 19B

PN----

TK00235TK00236TK00237TK00238TK00239TK00240TK00241----

Round hole EL Die(Type C for channel iron)

Size - - - -EL Die 10CEL Die 11CEL Die 12CEL Die 13CEL Die 14CEL Die 15CEL Die 16C - - - -

22

30.5

EL Punches

40

Front view ofEL Dies Type A, B & C

32

22.5

Side face ofEL Dies Type A, B & C

Sales Unit : 1 Piece

PN

TQ01279

TA99037

Part Name

Hex. Setscrew 8 x 14 for Elongated hole Die

Lock Nut Ass'y for D Punch 25

PUNCHES & DIES

14

Compact portable models meetyour versatile chamfering jobs

15CMild Steel

3C

2R, 3R

Mild Steel


• 4 / 5 / 6 mm Hex. Socket Screw Key : each 1 pc. • Spanner 24 x 27 : 1 pc. • Hook spanner 25-28 : 1 pc. • 3 mm T Wrench Key : 1 pc. • TA9A093 Insert 12.7 Ass'y (12 pcs./set ) : 1 set

• Carbon Brush Ass'y : 1 pc.• 4 mm Hex. Wrench Key : 1 pc.• Insert 12.7 with hole : 1 pc.• Insert Set Screw 4 x 7 : 1 pc.• Hex Nut M8 : 2 pcs.• 8 x 25 mm Hex. Socket Set Screw : 2 pcs.• Spanner T-15D : 1 pc.

• 3 & 4 mm Hex. Socket Screw Key : each 1 pc.• Spanner T-9F : 1 pc.• Hex. Nut M8 : 2 pcs.• 8 x 25 mm Hex. Socket Set Screw : 2 pcs.

• Insert 12.7 with hole : 1 pc.• Insert set screw 4 x 7 : 1 pc.• 5 mm Hex. Socket Screw Key : 1 pc.• Spanner 8 x 10 : 1 pc.• Spanner T-15D : 1 pc.• Adjustment gauge : 1 pc.

SpecificationsModel (Electric Tool)



Rated Current A

Rated Duty min

No-load Speed min-1 (rpm)

Chamfering Capacity

Chamfer Angle

Power Cord m

Mass (Weight) kg

HB-15B

Continuous

0C - 15C (7C per chamfering)

-

15˚ - 45˚

5

15

EMB-0307B

220 - 240 V AC, 50/60 Hz

1,010

4.6

Continuous

11,000

0C - 7C, 2R, 3R, 4R

0C - 3C, 2R, 3R, 4R

15˚ - 45˚

4

3.9

MB-03A

230 V or 115 V AC, 50/60 Hz

430

2 / 4.5

30

11,000

0C - 3C, 2R, 3R

-

45˚

2.5

2.5

ECB-0203

220 - 240 V AC, 50/60 Hz

450

2.1

30

11,000

0C - 3C, 2R, 3R

0C - 1.5C, 2R

45˚

2.5

2.5

115 V AC

910

10.5

3,340

230 V AC

910

4

2,750

Mild Steel

Stainless Steel

In case of chamfering 3R, an optional insert for 3R is necessary, and chamfering 2R, an optional guide sleeve 24 mm dia. and insert for 2R are necessary.

ECB-0203

A

CB

The limit of beveling width thatdepends on a chamfer angle.

Chamfering range of operationCB-02

Min. Diameter Min. Radius Min. Depth

Min. Diameter Min. Radius Min. Depth Min. Thickness

Chamferangle

Mild Steel(mm)

Stainless Steel(mm)

Mild Steel(mm)

Stainless Steel(mm)

45˚

30˚

15˚

A

7

3.8

1.5

B

7

6.6

5.6

A

3

2.2

1

A

3

2.2

1

B

3

3.8

3.8

C

4.2

4.4

3.9

B

3

3.8

3.8

C

4.2

4.4

3.9

C

9.9

7.6

5.8

A

7

4

2.2

B

7

7

8

C

9.9

8.1

8.3

EMB-0307B AMBL-0307 / AMB-0307

Finish a surface so fine thatpost-sanding is unnecessary

Column R-section can be chamferedwith optional attachment

Insert with 4-side blades per piecepractices good economy

Applicable to stainless steel andmild steel chamfering

Pipe outer edge can be alsoprocessed with standard accessories

Dust box collects swarf and chipseffectively

EMB-0307B

3C 7C

4R4R

179 mm 316.4 mm

189.6 mm

Stainless Steel Mild Steel

An outer R-part attachment allowschamfering of outer diameters witha radius greater than 170 mm

An optional inner head ass’y allowschamfering a pipe of inner diameterlarger than 100 mm (50R)

Applicable to stainless steel andmild steel chamfering

Minimum chamfering plate thicknessis 2 mm (Max.0.5C)

An optional straight plate allowschamfering a straight edge shoulder

1.5C

2R

Stainless Steel 3C

3R

Mild Steel

396 mm

220 mm

150 mm 278 mm

107.5 mm400 mm

136.4 mm

Portable Chamfering ToolsBEVELER

15

Select the suitable BEVELER model inaccordance with your applications

Applicable to stainless steel and mild steel chamfering

Simple to adjust chamfering depth and replace insert

Pipe outer edge can be also processed with standard accessories

180 mm

3C

7C

4R

Precisely adjust chamfer dimensions with accessory gauge

Versatility chamfer either inner or outer edges

2C

2R

136 mm

RingType

LeverType

Stainless Steel

Mild Steel

Mild Steel126 mm

202 mm

Optional

116 mm

180 mm

126 mm

177 mm

Standard Accessories• 3 & 4 mm Hex. Socket Screw Key : each 1 pc. • Spanner T-15F : 1 pc. • Hex Nut M8 : 2 pcs.

• 8 x 25 mm Hex. Socket Set Screw : 2 pcs.• Insert Set Screw 4 x 7 : 1 pc.

• Insert 9.525 with hole : 1 pc.• Adjustment gauge : 1 pc.• Spanner T-9F : 1 pc.

• Protective cap : 1 pc.• Hook Spanner 58-65 : 1 pc.

SpecificationsModel (Pneumatic Tool)

Air Pressure MPa (kgf/cm2)

Air Comsumption m3/min

No-load Speed min-1 (rpm)

Chamfering Capacity

Chamfer Angle

Mass (Weight) kg

AMBL-0307 / AMB-0307

0.59 (6)

0.9

14,000

0C - 7C, 2R, 3R, 4R

0C - 3C, 2R, 3R, 4R

15˚ - 45˚

2.9

CB-02

0.59 (6)

0.4

13,000

0C - 2C, 2R

-

45˚

1.8

Mild Steel

Stainless Steel

Portable Chamfering ToolsBEVELER

16

PN

TA9A093

TA9A896

TB01159

TB01791

TB01651

TB01790

TA9A386

TA9A592

TA9A638

TA9A728

TB02539

TA9A594

TB02857

TB03097

TB02862

TB03424

TQ01683

Indexable Insert 12.7 Ass'y

Indexable Insert 12.7 with hole Ass'y


Indexable Insert 12.7 Ass'y R2






Plate Ass'y for pipe

Attachment for small dia. pipe

Inner head Ass'y

Guide sleeve 24 mm dia. Ass'y

Plate Ass'y for straight line use

Dust Box Ass'y

Spanner T-9D

Spanner T-15D

Sales Unit

12 pcs./set

10 pcs./set

10 pcs./set

10 pcs./set

10 pcs./set

10 pcs./set

10 pcs./set

10 pcs./set

10 pcs./set

1 set

1 set

1 set

1 set

1 set

1 set

1 pc.

1 pc.

Application model

HB-15B

AMB-07

EMB-0307B, AMB-0307, AMBL-0307, ECB-0203

EMB-0307B, AMB-0307, AMBL-0307, ECB-0203

EMB-0307B, AMB-0307, AMBL-0307, ECB-0203

EMB-0307B, AMB-0307, AMBL-0307

MB-03A, CB-02

MB-03A, CB-02

MB-03A

HB-15B

EMB-0307B, AMB-0307, AMBL-0307

MB-03A

ECB-0203

ECB-0203

ECB-0203

MB-03A, CB-02

EMB-0307B, AMB-0307, AMBL-0307, ECB-0203

Remarks

For pipe 125 - 800 mm dia.

For pipe 80 - 200 mm dia.

For min. 100 mm dia.

For chamfering R2

Used with Plate Ass'y for straight line use

Description

Model SH-100A

SUPER HANDFILING

Pneumatic & Electric Power Tools,Labor-saving plus Improved Work Efficiency

OTHER PRODUCT LINES

A wide range of unique tools for boring and punching

Model JT-20

JET CHISELNEEDLE SCALER

Model S-250/S-500/S-1000

SUPER KELENPNEUMATIC SCALER

Model JEX-2800A

JET CHISELNEEDLE SCALER

Model A-300

AUTO CHISELAIR HAMMER

Model B-10N

BELTONPNEUMATIC BELT SANDER

Model ADR-100

AIR DRILLPNEUMATIC HAND DRILL

Model B-20N

BELTONPNEUMATIC BELT SANDER

Model MLG-70

MYTONPNEUMATIC GRINDER

Model L-25B

AIR SONICPNEUMATIC DIE GRINDER

Model MAS-40

MYTONPNEUMATIC SANDER

Model APS-150

PALM ORBITAL SANDERPNEUMATIC COMPACT SANDER

Model ACH-16

AIR CHIPPERSCALING

Model MAGW-40


Model CH-24

AIR CHIPPERSCALING

Model MLG-25


Professional Tools for High Technology

DLV7300 SeriesDLV7500/8500 SeriesDLV7000/8000 SeriesDLV7100/7200/8100/8200 SeriesDLV3100/3300 SeriesDLV5720/5720H/5740/5740H/5750 SeriesDLV5800 SeriesDLV30SP/30HP-MKG (with built-in brushless motors)

Models

NITTO KOHKI "delvo" Electric Screwdrivers are high-quality tools for professional use,with special emphasis on precise control of torque and long life. They apply just thecorrect amount of torque –with sure, positive control always at your fingertips.They're smooth and shockless in operation, too. NITTO KOHKI's customer-orientedservice system is directly connected to sales agents to ensure thatyou can use "delvo" Electric Screwdrivers with confidence.

TW-00/TW-0/TW-3/TW-5/TW-9/TW-15/TW-22/TW-30/TW-40/TW-50/TW-60/TW-70

TIGON Spring Balancer ImprovesWork Safety & Efficiency

Models

MEDO pumps are unique products featuring a Linear-motor-driven Free Piston System.NITTO KOHKI has made available a complete series of air compressors and suction pumps that incorporate this revolutionary mechanism.These are quite appropriate as air sources or suction power units for various pneumatically operated equipmentand apparatus in advanced industries.

DLV5720/5720H/5740 Series

DLV30SP-MKG

DLV30HP-MKG

Capacities ranging from 0.5 - 70 kg.

17

Quick Connecting Fluid Couplings are The World'sBest for both Quality and Quantity

HI CUPLA &HI CUPLA 200• One-way shut-off coupling with an automatic shut-off valve in the socket.• Important pars are hardened for excellent wear resistance and durability.

PlugFor hose connection17PH20PH30PH

For 1/4" hoseFor 1/4" hoseFor 3/8" hose

10PM20PM30PM

20PF30PF40PF

For Rc 1/8"For Rc 1/4"For Rc 3/8"

For R 1/4"For R 3/8"For R 1/2"

20PFF For G 1/4"

40PH400PH600PH800PH

For 1/2" hoseFor 1/2" hoseFor 3/4" hoseFor 1" hose

17SH20SH30SH


40SH400SH600SH800SH

For 1/2" hoseFor 1/2" hoseFor 3/4" hoseFor 1" hose

40PM400PM600PM800PM

400PF600PF800PF

For Rc 1/2"For Rc 1/2"For Rc 3/4"For Rc 1"

10SM20SM30SM


40SM400SM600SM800SM

For Rc 1/2"For Rc 1/2"For Rc 3/4"For Rc 1"

For R 1/2"For R 3/4"For R 1"

20SF30SF40SF


400SF600SF800SF

For R 1/2"For R 3/4"For R 1"

For hose connection

For female thread connection For female thread connection

For male thread connection For male thread connection

200-17SH200-20SH200-30SH


200-40SH For 1/2" hose

200-20SM200-30SM200-40SM


200-20SF200-30SF200-40SF


For hose connection

For female thread connection

For male thread connection

For male thread connection (parallel thread)

SocketP S

TypeBody material SizeWorking pressurePressure resistanceSeal materialWorking temperature range

SpecificationsHi Cupla

Steel (chrome-plated)1/8", 1/4", 3/8", 1/2", 3/4", 1"

1.5 MPa2.0 MPa

NBR-20˚C - +80˚C

Hi Cupla 200 Steel (chrome-plated)

1/8", 1/4", 3/8", 1/2"1.0 MPa1.5 MPa

NBR-5˚C - +60˚C

Plug

S22PHS33PHS32PH*

For OxygenFor Fuel GasFor Fuel Gas

For 1/4" , 5/16"For 5/16" , 3/8"For 1/4" , 5/16"

PH type (Hose barb)

S225PHS335PH

For OxygenFor Fuel Gas

For 5 mm IDFor 5 mm ID

PH type (Hose barb of smaller diameters)

S22PNS33PN



PN type (Nut type for small diameter hose)

S22PFS33PF


For oxygen torch sideFox fuel gas torch side

PF type (Female thread for torch connection)

S23PFB-2*S33PFB-2*


For oxygen torch sideFox fuel gas torch side

PFB type (Female thread with backflow stop valve)

S22SHS33SHS32SH*

For OxygenFor Fuel GasFor Fuel Gas

For 1/4" , 5/16"For 5/16" , 3/8"For 1/4" , 5/16"

SH type (Hose barb)

S225SHS335SH



SH type (Hose barb of smaller diameters)

S22SNS33SN



SN type (Nut type for small diameter hose)

S22SFS33SFS23SF*S33SF*

For OxygenFor Fuel GasFor OxygenFor Fuel Gas

For oxygen gauge sideFor fuel gas gauge sideFor oxygen gauge sideFor fuel gas gauge side

SF type (Female thread for torch connection)

S22SMS33SM


For Rc 1/4For Rc 3/8

SM type (Male thread)

SocketP S

Body material SizeWorking pressurePressure resistanceSeal materialWorking temperature range

SpecificationsSocket : Brass (chrome-plated) Plug : Steel (chrome-plated)

1/4", 5/16", 3/8"0.7 MPa1.0 MPa

NBR-20˚C - +80˚C

Full line-up consisting of 3,000 series, 20,000 type variations. The couplings eliminate inconvenience of thread-in orbolted flange connections, fluid leakage, or hose kinking but provide speedy control and maintenance of fluid piping.

HI CUPLA ACE• Plastic Cuplas with a bult-in locking mechanism.• Pressure ratings comprable to steel Cuplas.

LINE CUPLA 200• Enables several air lines to be taken simultaneously from one supply line.• Gives speedy branching of Hi Cupla.

OTHER PRODUCT LINES

*Made-to-order item. • Available hose sizes are ø5 mm x ø11.2 mm, ø5 mm x ø11.5 mm and ø5 mm x ø11.8 mm.

Male thread For regulator For extension hose For torch

Select the combination in accordance with your own application.

Suggested combinationSM x PH

Suggested combinationSF x PH

Suggested combinationSH x PH

Suggested combinationSH x PF

For Oxygen / Fuel Gas

Heavy-duty push-to-connect typeor oxyacetylene piping

Mini Cupla Super

Exclusively for weldingand cutting equipment.• From cylinders to torches, all piping connections associated with welding and cutting equipment are now in push-to- connect configurations.• Chrome-plated body for better corrosion resistance.• Heat-treated plugs for better durability.• Oxygen and fuel gas couplings have different configuration sizes with sleeves in different appearances, chrome plating for oxygen and copper plating for fuel gas, to prevent accidental interconnection.• Smaller diameter design enables wider range of applications.• Various types of end configurations have been standardized to comply with a wide range of welding and cutting equipment applications. Interchangeable with Mini Cupla.

18

Overseas Affiliates/Offices

NITTO KOHKI U.S.A. INC.TEL:+1-630-924-9393 FAX:+1-630-924-0303

NITTO KOHKI EUROPE CO., LTD.(UK)TEL:+44-1923-239-668 FAX:+44-1923-248-815

NITTO KOHKI DEUTSCHLAND GMBHTEL:+49-7157-22436 FAX:+49-7157-22437

NITTO KOHKI AUSTRALIA PTY. LTD.TEL:+61-7-3340-4600 FAX:+61-73340-4640

NITTO KOHKI CO., LTD. SINGAPOREBRANCHTEL:+65-6227-5360 FAX:+65-6227-0192

NITTO KOHKI CO., LTD. BANGKOKREPRESENTATIVE OFFICETEL:+66-2-632-0307 FAX:+66-2-632-0308

NITTO KOHKI CO., LTD. SHANGHAIREPRESENTATIVE OFFICETEL:+86-21-6415-3935 FAX:+86-21-6472-6957

NITTO KOHKI CO., LTD. SHENZHENREPRESENTATIVE OFFICETEL:+86-755-8375-2185 FAX:+86-755-8375-2187

DISTRIBUTED BY

Printed in Japan 10HW05- 1

NITTO KOHKI CO.,LTD.

Head Office 9-4, Nakaikegami 2-chome, Ohta-ku, Tokyo 146-8555 JapanPhone : +81-3-3755-1111 Fax : +81-3-3753-8791

E-mail : [email protected] : www.nitto-kohki.co.jp/e/

Specifications and designs are subject to change at any time without notice.

For environmental conservation, this print is made of the pulp blended with waste paper and printed with soy-based inks.

Documents

SAFETY GUIDE · 2019-05-13 · 3-4 Drilling holes in shaped steel Drilling holes in steel Speedy, high precision hole drilling Speedy, high precision hole drilling 5 CONTENTS PORTABLE