Rosemount 8800D Series Vortex Flowmeter...1 About this guide This guide provides basic guidelines for the Rosemount 8800D Series Vortex Flowmeter. It does not provide instructions

Quick Start Guide00825-0100-4004, Rev FF

April 2019

Rosemount™ 8800D Series VortexFlowmeter

1 About this guide

This guide provides basic guidelines for the Rosemount™ 8800D SeriesVortex Flowmeter. It does not provide instructions for detailedconfiguration, diagnostics, maintenance, service, troubleshooting,Explosion-proof, Flameproof, or Intrinsically Safe (I.S.) installations. Refer tothe reference manual for more instruction. The manuals and this quick startguide are also available electronically on EmersonProcess.com/Rosemount.

WARNING

Explosions could result in death or serious injury.Installation of this transmitter in an explosive environment must be inaccordance with the appropriate local, national, and international standards,codes, and practices. Review the approvals section of thereference manualfor any restrictions associated with a safe installation.

• Before connecting a handheld communicator in an explosiveatmosphere, make sure the instruments in the loop are installed inaccordance with intrinsically safe or non-incendive field wiring practices.

• Verify the operating atmosphere of the flowmeter is consistent with theappropriate product certifications.

• In an Explosion-proof/Flameproof installation, do not remove theflowmeter covers when power is applied to the unit. Electrical shock canresult in death or serious injury.

WARNING

Electrical shock can result in death or serious injury.• Avoid contact with the leads and terminals. High voltage that may be

present on leads can cause electrical shock.

1.1 Return policyEmerson procedures must be followed when returning equipment. Theseprocedures ensure legal compliance with government transportationagencies and help provide a safe working environment for Emersonemployees. Failure to follow Emerson procedures will result in yourequipment being refused delivery.

Quick Start Guide April 2019

2 Rosemount™ 8800D Series Vortex Flowmeter

1.2 Emerson Flow customer serviceEmail:

• Worldwide: [email protected]

• Asia-Pacific: [email protected]

Telephone:

North and South America Europe and Middle East Asia Pacific

United States 800 522 6277 U.K. 0870 2401978

Australia 800 158 727

Canada +1 303 5275200

TheNetherlands

+31 (0) 704136 666

New Zealand 099 128 804

Mexico +41 (0) 417686 111

France 0800 917 901 India 800 440 1468

Argentina +54 11 48377000

Germany 0800 1825347

Pakistan 888 550 2682

Brazil +55 15 34138000

Italy 8008 77334 China +86 21 28929000

Venezuela +58 26 17313446

Central &Eastern

+41 (0) 417686 111

Japan +81 3 57696803

Russia/CIS +7 495 9819811

South Korea +82 2 34384600

Egypt 0800 0000015

Singapore +65 6 7778211

Oman 800 70101 Thailand 001 800 4416426

Qatar 431 0044 Malaysia 800 814 008

Kuwait 663 299 01

South Africa 800 991 390

Saudi Arabia 800 844 9564

UAE 800 04440684

April 2019 Quick Start Guide

Quick Start Guide 3

mailto:[email protected]

mailto:[email protected]

2 Installation

2.1 Mount the flowmeterDesign process piping so the meter body will remain full, with no entrappedair. The vortex flowmeter can be installed in any orientation withoutaffecting accuracy. However, the following are guidelines for certaininstallations.

2.1.1 Vertical mounting

If the vortex flowmeter will be installed in a vertical orientation:

• Install upward or downward flow for gas or steam.

• Install upward flow for liquids.

Figure 2-1: Vertical installation

BA

A. Gas flowB. Liquid or gas flow



2.1.2 Horizontal mounting

Figure 2-2: Horizontal installation

BA

A. Preferred installation—meter body installed with electronics to side ofpipe

B. Acceptable installation—meter body installed with electronics above pipe

For steam and fluids with small solids content, it is recommended to havethe flowmeter installed with the electronics to the side of the pipe. This willminimize potential measurement errors by allowing the condensate orsolids to flow under the shedder bar without interrupting the vortexshedding.

2.1.3 High temperature mounting

The maximum temperature for integral electronics is dependent on theambient temperature where the flowmeter is installed. The electronics mustnot exceed 185 °F (85 °C).

Figure 2-3 shows combinations of ambient and process temperaturesneeded to maintain a housing temperature of less than 185 °F (85 °C).


Quick Start Guide 5

Figure 2-3: Ambient/Process temperature limits

B

A C

200 (93)

180(82)

160 (71)

140 (60)

120 (49)

100 (38)

80 (27)

60 (16)0

200

(93)

300

(149

)

400

(204

)

500

(260

)

600

(316

)

700

(371

)

800

(427

)

900

(482

)

1000

(538

)

100

(38)

A. Ambient temperature °F (°C)B. Process temperature °F (°C)C. 185 °F (85 °C) Housing temperature limit.

NoteThe indicated limits are for horizontal pipe and vertical meter position, withmeter and pipe insulated with 3 in. (77 mm) of ceramic fiber insulation.

The following orientations are recommended for applications with highprocess temperatures.

• Install with electronics head beside or below process pipe.

• Insulation around pipe may be necessary to maintain ambienttemperature below 185 °F (85 °C).

NoteInsulate pipe and meter body only. Do not insulate support tube bracket ortransmitter so heat can be dissipated.

2.1.4 Steam installations

Avoid installation shown in Figure 2-4. Such conditions may cause a water-hammer condition at start-up due to trapped condensation.



Figure 2-4: Improper installation

2.1.5 Upstream/downstream requirements

The flowmeter may be installed with a minimum of ten straight pipediameters (D) upstream and five straight pipe diameters (D) downstream byfollowing the K-factor corrections as described in the 8800 InstallationEffects Technical Data Sheet (00816-0100-3250). No K-factor correction isrequired if 35 straight pipe diameters upstream (35D) and 10 straight pipediameters downstream (10D) are present.

2.1.6 External pressure/temperature transmitters

When using pressure and temperature transmitters in conjunction with theflowmeter for compensated mass flows, install the transmitters downstreamof the flowmeter as shown in Figure 2-5.


Quick Start Guide 7

Figure 2-5: Upstream/Downstream piping

A C

BD

A. Pressure transmitterB. Four straight pipe diameters downstreamC. Temperature transmitterD. Six straight pipe diameters downstream

2.1.7 Wafer style installation

Figure 2-6: Wafer style installation

C

A

B

B

D

A. Installation studs and nuts (supplied by customer)B. Alignment ringC. Gaskets (supplied by customer)D. Flow direction



2.1.8 Flanged style installation

Figure 2-7: Flanged style installation

C

A

B

A. Installation bolts and nuts (supplied by customer)B. Gaskets (supplied by customer)C. Flow direction

NoteThe required bolt load for sealing the gasket joint is affected by severalfactors, including operating pressure, gasket material, width, and condition.A number of factors also affect the actual bolt load resulting from ameasured torque, including condition of bolt threads, friction between thenut head and the flange, and parallelism of the flanges. Due to theseapplication-dependent factors, the required torque for each application maybe different. Follow the guidelines outlined in ASME PCC-1 for proper bolttightening. Make sure the flowmeter is centered between flanges of thesame nominal size as the flowmeter.

2.1.9 Insert integral temperature sensor (MTA option only)

NoteStep number of procedure corresponds with number in Figure 2-8.


Quick Start Guide 9

Figure 2-8: Thermocouple assembly

1. Slide the thermocouple bolt (1) over the thermocouple (TC).

2. Place the 2-part ferrule (2) over the end tip of the thermocouple (TC).

3. Insert the thermocouple in to the thermowell hole (TW) on thebottom side of the meter body.

ImportantCarefully push the thermocouple in to the thermowell completely.This is critical to get the proper insertion depth. Then thread thethermocouple bolt in to the hole.

4. When the thermocouple bolt is hand tight, mark the position of thebolt in relation to the meter body (the mark will help determinerotations). Using a ½-in. wrench turn the bolt clockwise ¾ turn toseat the ferrule.

NoteAfter completing Step 4, the ferrule and thermocouple bolt will bepermanently installed on the thermocouple.

5. Verify the rubber O-ring is installed on the electronics connectionend of the thermocouple.

6. Verify the 2.5 mm hex head screw is installed.

7. Insert the electronics end connector in to the transmitter housing.Tighten the screw with a 2.5 mm hex bit to secure the connection.

ImportantDo not over tighten hex screw.



2.2 Install remote electronicsIf you order one of the remote electronics options (options R10, R20, R30, orRXX), the flowmeter assembly ships in two parts:

1. The meter body with an adapter installed in the support tube and aninterconnecting coaxial cable attached to it.

2. The electronics housing installed on a mounting bracket.

If you ordered the armored remote electronics options, follow the sameinstructions as for the standard remote cable connection with the exceptionthat the cable may not need to be run through conduit. Armored includesthe glands.

1. Mount the meter body in the process flow line as described in Mountthe flowmeter.

2. Mount the bracket and electronics housing in the desired location.The housing can be repositioned on the bracket to facilitate fieldwiring and conduit routing.

Refer to Figure 2-9 and these steps to connect the loose end of the coaxialcable to the electronics housing.


Quick Start Guide 11

Figure 2-9: Remote electronics installation

AB

C

ED

FG

H

I

J

K

L

M

N

O

P

A. 1/2 NPT conduit adapter or cable gland (supplied by customer)B. Coaxial cableC. Meter adapterD. UnionE. WasherF. NutG. Sensor cable nutH. Support tube

I. Meter bodyJ. Electronics housing

K. Coaxial cable nutL. Conduit adapter (optional-supplied by customer)

M. Housing adapter screwsN. Housing adapterO. Housing base screwP. Ground connection

1. If you plan to run the coaxial cable in conduit, carefully cut theconduit to the desired length to provide for proper assembly at thehousing. A junction box may be placed in the conduit run to provide aspace for extra coaxial cable length.



CAUTION

The coaxial remote cable cannot be field terminated or cut to length.Coil any extra coaxial cable with no less than a 2-in. (51 mm) radius.

2. Slide the conduit adapter or cable gland over the loose end of thecoaxial cable and fasten it to the adapter on the meter body supporttube.

3. If using conduit, route the coaxial cable through the conduit.

4. Place a conduit adapter or cable gland over the end of the coaxialcable.

5. Remove the housing adapter from the electronics housing.

6. Slide the housing adapter over the coaxial cable.

7. Remove one of the four housing base screws.

8. Attach and securely tighten the coaxial cable nut to the connectionon the electronics housing.

9. Attach the coaxial cable ground wire to the housing via the housingbase ground screw.

10. Align the housing adapter with the housing and attach with twoscrews.

11. Tighten the conduit adapter or cable gland to the housing adapter.

CAUTION

To prevent moisture from entering the coaxial cable connections,install the interconnecting coaxial cable in a single dedicated conduitrun or use sealed cable glands at both ends of the cable.

NoteRefer to the reference manual for details for the CPA option.



3 Consider housing rotation

The entire electronics housing may be rotated in 90° increments for easyviewing. Use the following steps to change the housing orientation,

1. Loosen the three housing rotation set screws at the base of theelectronics housing with a 5/32” hex wrench by turning the screwsclockwise (inward) until they clear the support tube.

2. Slowly pull the electronics housing out of the support tube.

CAUTION

Do not pull the housing more than 1.5 in. (40 mm) from the top ofthe support tube until the sensor cable is disconnected. Damage tothe sensor may occur if this sensor cable is stressed.

3. Unscrew the sensor cable from the housing with a 5/16” open endwrench.

4. Rotate the housing to the desired orientation.

5. Hold it in this orientation while you screw the sensor cable onto thebase of the housing.

CAUTION

Do not rotate the housing while the sensor cable is attached to thebase of the housing. This will stress the cable and may damage thesensor.

6. Place the electronics housing into the top of the support tube.

7. Use a hex wrench to turn the three housing rotation screws counter-clockwise (outward) to engage the support tube.



4 Set jumpers

Adjust jumpers to desired settings.

4.1 HART jumpersIf alarm and security jumpers are not installed, the flowmeter will operatenormally with the default alarm condition alarm high and the security off.

Figure 4-1: HART jumpers and LCD display

ALARM

HI LO

ON OFF

SECURITY

4.2 Foundation fieldbusIf security and simulate enable jumpers are not installed, the flowmeter willoperate normally with the default security “OFF” and simulate enable “OFF”.

Figure 4-2: Foundation fieldbus jumpers and LCD display

SIMULATE ENABLEOFF ON

ON OFFSECURITY



5 Connect wiring and power up

5.1 Power supply (HART)The dc power supply should provide power with less than two percent ripple.The total resistance load is the sum of the resistance of the signal leads andthe load resistance of the controller, indicator, and related pieces. Note thatthe resistance of intrinsic safety barriers, if used, must be included.

Figure 5-1: Load limitation

CA

B

B

D

1500

1250

1000

750

500

250

010.8 16.8 22.8 28.8 34.8 42

A. Rloop in ohmsB. Power supply voltage

Maximum Loop Resistance = 41.7 (Power Supply Voltage - 10.8) The FieldCommunicator requires a minimum loop resistance of 250 ohms.

5.2 Power supply (Foundation fieldbus)The flowmeter requires 9-32 Vdc at the power terminals. Each fieldbuspower supply requires a power conditioner to decouple the power supplyoutput from the fieldbus wiring segment.

5.3 Conduit installationPrevent condensation in any conduit from flowing into the housing bymounting the flowmeter at a high point in the conduit run. If the flowmeteris mounted at a low point in the conduit run, the terminal compartmentcould fill with fluid.

If the conduit originates above the flowmeter, route conduit below theflowmeter before entry. In some cases a drain seal may need to be installed.



Figure 5-2: Proper conduit installation

C

B

D

A A

A. Conduit line

5.4 Wire the flowmeterUse the following figures and steps to wire the flowmeter:

Figure 5-3: 4–20 mA wiring

A

+

-

RL ≥ 250 Ω

A. Power supply

Figure 5-4: 4–20 mA and pulse wiring with electronic totalizer/counter

+

-

RL ≥250 Ω

+

-

100 Ω ≤ RL ≤ 100 kΩ

A B

A. Power supplyB. Power supply with counter



Figure 5-5: Flowmeter field wiring for Foundation fieldbus protocol

A

B CD

FE G G

H

A. 6234 ft (1900 m) max, depending upon cable characterisitcsB. Integrated power conditioner and filterC. TerminatorsD. Fieldbus segmentE. Power supplyF. (Trunk)

G. (Spur)H. Devices 1 through 16(1)

NoteThe power supply, filter, first terminator, and configuration tool are typicallylocated in the control room.

1. Remove the housing cover on the side marked FIELD TERMINALS.

2. Connect the positive lead to the “+” terminal and the negative leadto the “−” terminal as shown in Figure 5-3 for HART installations andFigure 5-5 for Foundation fieldbus installations.

NoteFoundation fieldbus terminals are not polarity sensitive.

3. For HART installations utilizing the pulse output, connect the positivelead to the “+” terminal of the pulse output and the negative lead tothe “−” terminal of the pulse output as shown in Figure 5-4. A

(1) Intrinsically safe installations may allow fewer devices per I.S. barrier.



separate 5 to 30 Vdc power supply is required for the pulse output.Maximum switching current for the pulse output is 120 mA.

CAUTION

Do not connect the powered signal wiring to the test terminals.Power could damage the test diode in the test connection. Twistedpairs are required to minimize noise pick up in the 4–20 mA signaland digital communication signal. For high EMI/RFI environments,shielded signal wire is required and preferred in all other installations.Use 24 AWG or larger wire and do not exceed 5,000 feet (1,500meters). For ambient temperatures above 140 °F (60 °C) use wirerated to 176 °F (80 °C) or higher.

Figure 5-3 and Figure 5-4 show wiring connections necessary topower a transmitter and enable communications with a hand-heldField Communicator.

Figure 5-5 shows wiring connections necessary to power atransmitter with Foundation fieldbus.

4. Plug and seal unused conduit connections. Use pipe sealing tape orpaste on threads to ensure a moisture-tight seal. Housing conduitentries marked with M20 will require M20 x 1.5 blanking plug thread.Unmarked conduit entries will require a ½–14 NPT blanking plugthread.

NoteStraight threads require a minimum of three wraps of tape to obtaina tight seal.

5. If applicable, install wiring with a drip loop. Arrange the drip loop sothe bottom is lower than the conduit connections and the flowmeterhousing.

NoteInstallation of the transient protection terminal block does notprovide transient protection unless the transmitter case is properlygrounded.

CAUTION

Flowmeters ordered with painted meter body may be subject toelectrostatic discharge. To avoid electrostatic charge build-up, donot rub the meter body with a dry cloth or clean with solvents.



5.5 Secure cover jam screwFor transmitter housings shipped with a cover jam screw, the screw shouldbe properly installed once the transmitter has been wired and powered up.The cover jam screw is intended to disallow the removal of the transmittercover in flameproof environments without the use of tooling.

1. Verify the cover jam screw is completely threaded into the housing.

2. Install the transmitter housing cover and verify that the cover is tightagainst the housing.

3. Using an M4 hex wrench, loosen the jam screw until it contacts thetransmitter cover.

4. Turn the jam screw an additional ½ turn counterclockwise to securethe cover.

CAUTION

Application of excessive torque may strip the threads.

5. Verify that the cover cannot be removed.



6 Verify configuration

Before operating the flowmeter in an installation, you should review theconfiguration data to ensure that it reflects the current application. In mostcases, all of these variables are pre-configured at the factory. Configurationmay be required if your flowmeter is not configured or if the configurationvariables need revision. Rosemount recommends the following variables arereviewed before startup.

HART

• Tag

• Transmitter Mode

• Process Fluid

• Reference K-Factor

• Flange Type

• Mating Pipe ID

• PV Units

• PV Damping

• Process Temperature Damping

• Fixed Process Temperature

• Auto Adjust Filter

• LCD Display Configuration (For units with a display only)

• Density Ratio (For Standard or Normal flow units only)

• Process Density and Density Units (For mass flow units only)

• Variable Mapping

• Range Values

• Pulse Output Configuration (For units with a pulse output only)

Foundation fieldbus configuration

• Tag

• Transmitter Mode

• Process Fluid

• Reference K-Factor

• Flange Type



• Mating Pipe ID

• PV Units (configured in the AI block)

• Flow Damping

• Process Temperature Damping

• Fixed Process Temperature

• Auto Adjust Filter

• LCD Display Configuration (for units with a display only)

• Density Ratio (for Standard or Normal flow units only)

• Process Density and Density Units (for mass flow units only)

Table 6-1: Fast Keys for Rosemount 8800D Device Revision 1 DD Revision2 and Device Revision 2 DD Revision 1

Function HART Fast Keys Function HART Fast Keys

Alarm Jumpers 1, 4, 2, 1, 3 Meter BodyNumber

1, 4, 1, 5

Analog Output 1, 4, 2, 1 Minimum Span 1, 3, 8, 3

Auto Adjust Filter 1, 4, 3, 1, 4 Num Req Preams 1, 4, 2, 3, 2

Base Time Unit 1, 1, 4, 1, 3, 2 Poll Address 1, 4, 2, 3, 1

Base Volume Unit 1, 1, 4, 1, 3, 1 Process Fluid Type 1, 3, 2, 2

Burst Mode 1, 4, 2, 3, 4 Process Variables 1, 1

Burst Option 1, 4, 2, 3, 5 Pulse Output 1, 4, 2, 2, 1

Burst Variable 1 1, 4, 2, 3, 6, 1 Pulse Output Test 1, 4, 2, 2, 2

Burst Variable 2 1, 4, 2, 3, 6, 2 PV Damping 1, 3, 9

Burst Variable 3 1, 4, 2, 3, 6, 3 PV Mapping 1, 3, 6, 1

Burst Variable 4 1, 4, 2, 3, 6, 4 PV Percent Range 1, 1, 2

Burst XmtrVariables

1, 4, 2, 3, 6 QV Mapping 1, 3, 6, 4

ConversionNumber

1, 1, 4, 1, 3, 4 Range Values 1, 3, 8

D/A Trim 1, 2, 5 Review 1, 5

Date 1, 4, 4, 5 Revision Numbers 1, 4, 4, 7

Descriptor 1, 4, 4, 3 Scaled D/A Trim 1, 2, 6

Density Ratio 1, 3, 2, 4, 1, 1 Self Test 1, 2, 1, 5



Table 6-1: Fast Keys for Rosemount 8800D Device Revision 1 DDRevision 2 and Device Revision 2 DD Revision 1 (continued)


Device ID 1, 4, 4, 7, 6 Signal to TriggerRatio

1, 4, 3, 2, 2

Electronics Temp 1, 1, 4, 7, 1 STD/ Nor FlowUnits

1, 1, 4, 1, 2

Electronics TempUnits

1, 1, 4, 7, 2 Special Units 1, 1, 4, 1, 3

Filter Restore 1, 4, 3, 3 Status 1, 2, 1, 1

Final AssemblyNumber

1, 4, 4, 7, 5 SV Mapping 1, 3, 6, 2

Fixed ProcessDensity

1, 3, 2, 4, 2 Tag 1, 3, 1

Fixed ProcessTemperature

1, 3, 2, 3 Total 1, 1, 4, 4, 1

Flange Type 1, 3, 4 Totalizer Control 1, 1, 4, 4

Flow Simulation 1, 2, 4 Transmitter Mode 1, 3, 2, 1

Installation Effects 1, 4, 1, 6 TV Mapping 1, 3, 6, 3

K-factor(Reference)

1, 3, 3 Trigger Level 1, 4, 3, 2, 5

Local Display 1, 4, 2, 4 URV 1, 3, 8, 1

Loop Test 1, 2, 2 User Defined Units 1, 1, 4, 1, 3, 3

Low Flow Cutoff 1, 4, 3, 2, 3 USL 1, 3, 8, 4

Low Pass Filter 1, 4, 3, 2, 4 SheddingFrequency

1, 1, 4, 6

LRV 1, 3, 8, 2 Variable Mapping 1, 3, 6

LSL 1, 3, 8, 5 Velocity Flow 1, 1, 4, 3

Manufacturer 1, 4, 4, 1 Velocity Flow Base 1, 1, 4, 3, 3

Mass Flow 1, 1, 4, 2, 1 Volumetric Flow 1, 1, 4, 1

Mass Flow Units 1, 1, 4, 2, 2 Wetted Material 1, 4, 1, 4

Mating Pipe ID(Inside Diameter)

1, 3, 5 Write Protect 1, 4, 4, 6

Message 1, 4, 4, 4



Table 6-2: Fast Keys for Rosemount 8800D Device Revision 2 DD Revision3


Alarm Direction 1, 3, 1, 3, 2 Percent of Range 3, 4, 3, 2

Analog Output 3, 4, 3, 1 Polling Address 2, 2, 7, 1

Analog Trim 3, 4, 3, 6 Primary VariableDamping

2, 1, 4, 1

Base Time Unit 2, 2, 2, 3, 2 Primary Variable 2, 2, 2, 1, 1

Base Volume Unit 2, 2, 2, 3, 1 Process DensityUnits

2, 2, 2, 2, 6

Burst Mode 2, 2, 7, 2 Process Fluid Type 2, 2, 1, 1, 2

Burst Option 2, 2, 7, 3 Process Temp Units 2, 2, 3, 1, 2

Burst Slot 0 2, 2, 7, 4, 1 Process Variables 3, 2, 1

Burst Slot 1 2, 2, 7, 4, 2 Pulse Output 3, 2, 4, 4

Burst Slot 2 2, 2, 7, 4, 3 Pulse Output Test 3, 5, 3, 4

Burst Slot 3 2, 2, 7, 4, 4 Recall FactoryCalibration

3, 4, 3, 8

Burst VariableMapping

2, 2, 7, 4, 5 Reference K-Factor 2, 2, 1, 2, 1

Compensated K-Factor

2, 2, 1, 2, 2 Reset Transmitter 3, 4, 1, 2

ConversionNumber

2, 2, 2, 3, 4 Restore DefaultFilters

2, 1, 4, 6

Date 2, 2, 8, 2, 1 Revision Numbers 2, 2, 8, 3

Descriptor 2, 2, 8, 2, 2 Scaled Analog Trim 3, 4, 3, 7

Density Ratio 2, 2, 3, 3, 2 2nd Variable 2, 2, 2, 1, 2

Device ID 2, 2, 8, 1, 5 Self Test 3, 4, 1, 1

Display 2, 1, 1, 2 Set VariableMapping

2, 2, 2, 1, 5

Electronics Temp 3, 2, 5, 4 SheddingFrequency

3, 2, 4, 2


2, 2, 2, 2, 5 Signal Strength 3, 2, 5, 2


2, 2, 8, 1, 4 Special Flow Unit 2, 2, 2, 3, 5



Table 6-2: Fast Keys for Rosemount 8800D Device Revision 2 DDRevision 3 (continued)



2, 2, 1, 1, 5 Special VolumeUnit

2, 2, 2, 3, 3


2, 2, 1, 1, 4 Status 1, 1, 1

Flange Type 2, 2, 1, 4, 2 Tag 2, 2, 8, 1, 1

Flow Simulation 3, 5, 1 3rd Variable 2, 2, 2, 1, 3

4th Variable 2, 2, 2, 1, 4 Total 1, 3, 6, 1

Installation Effects 2, 2, 1, 1, 7 TotalizerConfiguration

1, 3, 6, 3

Lower Range Value 2, 2, 4, 1, 4 Totalizer Control 1, 3, 6, 2

Lower Sensor Limit 2, 2, 4, 1, 5, 2 Transmitter Mode 2, 2, 1, 1, 1

Loop Test 3, 5, 2, 6 Trigger Level 2, 1, 4, 5

Low Flow Cutoff 2, 1, 4, 3 Upper Range Value 2, 2, 4, 1, 3

Low-pass CornerFrequency

2, 1, 4, 4 Upper Sensor Limit 2, 2, 4, 1, 5, 1

Manufacturer 2, 2, 8, 1, 2 Velocity Flow 3, 2, 3, 4

Mass Flow 3, 2, 3, 6 Velocity Flow Units 2, 2, 2, 2, 2

Mass Flow Units 2, 2, 2, 2, 4 VelocityMeasurement Base

2, 2, 2, 2, 3

Mating Pipe ID(Inside Diameter)

2, 2, 1, 1, 6 Volume Flow 3, 2, 3, 2

Message 2, 2, 8, 2, 3 Volume Flow Units 2, 2, 2, 2, 1

Meter BodyNumber

2, 2, 1, 4, 5 Wetted Material 2, 2, 1, 4, 1

Minimum Span 2, 2, 4, 1, 6 Write Protect 2, 2, 8, 1, 6

Optimize DSP 2, 1, 1, 3

Table 6-3: Fast Keys for Rosemount 8800D HART 7 Device Revision 2 (DDRevision 1)/ HART 5 Device Revision 3 (DD Revision 1)

Function Fast Key Function Fast Key

Analog Output 3, 4, 3, 1 Polling Address 2, 2, –(1), 2, 1

Analog Trim 3, 4, 3, 7 Primary Variable 2, 2, 2, 1



Table 6-3: Fast Keys for Rosemount 8800D HART 7 Device Revision 2 (DDRevision 1)/ HART 5 Device Revision 3 (DD Revision 1) (continued)


Base Mass Unit(MF)

2, 2, 2, 8, 1 Process Fluid Type 2, 2, 1, 1, 3

Base ProcessDensity

2, 2, 3, 2, 1 Process Variables 3, 2, 3

Base Time Unit(CVF)

2, 2, 2, 9, 4 Pulse Output 3, 2, 5, 3

Base Time Unit(MF)

2, 2, 2, 8, 4 Pulse Output Test 3, 5, 3, 4

Base Time Unit (VF) 2, 2, 2, 7, 4 Reference K-Factor 2, 2, 1, 2, 1

Base Volume Unit(CVF)

2, 2, 2, 9, 1 Reset Transmitter 3, 4, 4, 1, 2

Base Volume Unit(VF)

2, 2, 2, 7, 1 Restore DefaultFilters

2, 1, 4, 6

Compensated K-Factor

2, 2, 1, 2, 2 Restore FactoryCalibration

3, 4, 3, 9

Conversion Factor(CVF)

2, 2, 2, 9, 2 Revision Numbers 2, 2, –(1), 2

Conversion Factor(MF)

2, 2, 2, 8, 2 Scaled Analog Trim 3, 4, 3, 8

Conversion Factor(VF)

2, 2, 2, 7, 2 Second Variable 2, 2, 2, 2

Date 2, 2, –(1), 1, 5 Self Test 3, 4, 4, 1, 1

CorrectedVolumetric Flow

3,2,1 Set Damping 2, 1, 4, 1

CorrectedVolumetric FlowUnits

2,2,2,6,2 Set Low FlowCutoff

2, 1, 4, 3

Density Ratio 2, 2, 3, 4 Set Low-passCorner Frequency

2, 1, 4, 4

Descriptor 2, 2, –(1), 1, 6 Set Trigger Level 2, 1, 4, 5

Device ID 2, 2, –(1), 1 SheddingFrequency

3, 2, 5, 1

Device Status 1, 1 Signal Strength 3, 4, 2, 1, 4

Display 2, 1, 1, 2 Special Flow Unit(CVF)

2, 2, 2, 9, 5



Table 6-3: Fast Keys for Rosemount 8800D HART 7 Device Revision 2 (DDRevision 1)/ HART 5 Device Revision 3 (DD Revision 1) (continued)


Electronics Temp 3, 2, 6 Special Flow Unit(MF)

2, 2, 2, 8, 5


2, 2, 2, 6, 7 Special Flow Unit(VF)

2, 2, 2, 7, 5


2, 2, 1, 4, 3 Special VolumeUnit

2, 2, 2, 7, 3


2, 2, 1, 1, 5 Tag 2, 2, –(1), 1, 1


2, 2, 1, 1, 4 Third Variable 2, 2, 2, 3

Flange Type 2, 2, 1, 4, 2 Total 2, 2, 4, 3, 1

Flow Simulation 3, 5, 1, 2, 1 TotalizerConfiguration

2, 2, 4, 3, 3

Fourth Variable 2, 2, 2, 4 Totalizer Control 2, 2, 4, 3, 2

Loop Test 3, 5, 2, 7 Transmitter Mode 2, 2, 1, 1, 1

Lower Range Value 2, 2, 4, 1, 4 Upper Range Value 2, 2, 4, 1, 3

Lower Sensor Limit 2, 2, 4, 1, 6 Upper Sensor Limit 2, 2, 4, 1, 5

Mass Flow 3, 2, 1 Variable Mapping 2, 2, 2, 5

Mass Flow Units 2, 2, 2, 6, 5 Velocity Flow 3, 2, 1

Message 2, 2, –(1), 1, 7 Velocity Flow Units 2, 2, 2, 6, 3

Meter Factor 2, 2, 1, 1, 7 VelocityMeasurement Base

2, 2, 2, 6, 4

Minimum Span 2, 2, 4, 1, 7 Volume Flow 3, 2, 1

Optimize DSP 2, 1, 1, 3 Volume Flow Units 2, 2, 2, 6, 1

Percent of Range 3, 4, 3, 2 Wetted Material 2, 2, 1, 4, 1

Pipe InsideDiameter

2, 2, 1, 1, 6 Write Protect 2, 2, 4, 1

(1) These items are in a list format without numeric labels. To access these features,you must scroll to this option in the HART Communicator.

NoteFor detailed configuration information, refer to the product referencemanual.



7 Safety instrumented systems installation

For safety certified installations, refer to the Rosemount 8800D SafetyManual (Document # 00809-0200-4004) for installation procedure andsystem requirements.



8 Product certifications

For information about product certifications, refer to Rosemount™ 8800DSeries Vortex Flowmeter Approval Document (00825-VA00-0001). You can findit at emerson.com or contact our Customer Service Center (see contactinformation on the last page of this document).



http://www.emerson.com





*00825-0100-4004*Quick Start Guide

00825-0100-4004, Rev. FFApril 2019

Emerson Automation Solutions USA7070 Winchester CircleBoulder, Colorado USA 80301T +1 303-527-5200T +1 800-522-6277F +1 303-530-8459www.emerson.com

Emerson Automation Solutions Asia1 Pandan CrescentSingapore 128461Republic of SingaporeT +65 6363-7766F +65 6770-8003

Emerson Automation Solutions EuropeNeonstraat 16718 WX EdeThe NetherlandsT +31 (0) 70 413 6666F +31 (0) 318 495 556www.micromotion.nl

Emerson Automation Solutions UnitedKingdomEmerson Process Management LimitedHorsfield WayBredbury Industrial EstateStockport SK6 2SU U.K.T +44 0870 240 1978F +44 0800 966 181

©2019 Rosemount, Inc. All rights reserved.

The Emerson logo is a trademark and service mark of Emerson Electric Co.Rosemount, 8600, 8700, 8800 marks are marks of one of the EmersonAutomation Solutions family of companies. All other marks are propertyof their respective owners.

http://www.emerson.com

http://www.micromotion.nl

Documents

Rosemount 8800D Series Vortex Flowmeter...1 About this guide This guide provides basic guidelines for the Rosemount 8800D Series Vortex Flowmeter. It does not provide instructions