Rosemount 8800D Series Vortex Flowmeter€¦ · Rosemount 8800D Series Vortex Flowmeter. ... Rosemount 8800D 8800D MULTIVARIABLE VORTEX REDUCES INSTALLATION COSTS, ... manufacturer

Product Data Sheet00813-0100-4004, Rev HAApril 2010 Rosemount 8800D

Rosemount 8800D Series Vortex Flowmeter

HART® AND FOUNDATION™ FIELDBUS PROTOCOLS

• Available with optional MultiVariable output and temperature compensated mass flow for saturated steam.

• Available in wafer, flanged, dual, reducer and high pressure designs.

• Available in Reducer™ Vortex which extends the measurable flow range, reduces installation costs, and minimizes project risk.

• All-welded, non-clog design eliminates ports and gaskets.

• Adaptive Digital Signal Processing (ADSP) provides vibration immunity and the ability to optimize the measurable flow range.

• With the unique isolated sensor design, the CriticalProcess™ Vortex allows for replacement without breaking the process seal.

• Simplified troubleshooting through device diagnostics and meter verification.

www.ros

Contents

Specifications........................................................................................................... page 6

Typical Flow Ranges................................................................................................ page 11

Product Certifications............................................................................................... page 22

Dimensional Drawings.............................................................................................. page 28

Ordering Information................................................................................................ page 44

emount.com

Product Data Sheet00813-0100-4004, Rev HA

April 2010Rosemount 8800D

2

THE ROSEMOUNT 8800D DELIVERS RELIABILITY

• Rosemount Reliability -The 8800D Vortex eliminates impulse lines, ports, and gaskets to improve reliability.

• Non-clog Design - Unique gasket-free construction which has no ports that can clog.

• Vibration Immunity - Mass Balancing of the sensor system, and Adaptive Digital Signal Processing (ADSP) provide Vibration immunity.

• Replaceable Sensor - The sensor is isolated from the process and can be replaced without breaking the process seals. All line sizes use the same sensor design allowing a single spare to serve every meter. The CriticalProcess Vortex enhances the ability to replace the sensor without shutting down the process.

• Simplified Troubleshooting - Device Diagnostics enable field verification of Meter Electronics and Sensor with no process shutdown.

THE ROSEMOUNT 8800D OFFERING

• The 8800D is available in wafer style meter bodies for 1/2 through 8-in. line sizes, and ASME B16.5 (ANSI), DIN, or JIS flanged style meter bodies for 1/2 through 12-in. line sizes.

• Alignment rings, provided with each wafer-style flowmeter, ensure that the meter body is properly centered with the adjacent piping.

• The wafer, flanged, and weld end style meter bodies are available in 316 stainless steel and nickel alloy materials of construction.

• Available up to ASME class 1500 for 1 through 8-in. (25 mm through 200 mm) and ASME class 900 for 1/2-in. (15 mm) through 8-in. (200 mm).

• Available with FOUNDATION fieldbus functionality which includes Device Diagnostics and PlantWeb Alerts.


3

THE ROSEMOUNT 8800DR REDUCER VORTEX EXTENDS THE MEASURABLE FLOW RANGE AT A REDUCED COST

• Rosemount Reliability - Designed with same electronics, sensor, and meter body as the 8800D.

• Reduced Cost - Eliminates field assembly and welding of separate reducers and piping reducing installed cost by as much as 50%.

• Extended Measurable Flow - Low-end flow range is doubled with the Rosemount 8800DR Reducer Vortex.

• Reduced Project Risk - Reducer Vortex and the Standard Vortex have the same face-to-face dimension. As a result either meter can be used without affecting pipe layout.

• Available as flanged meter for 1 through 12-in. stainless steel and nickel alloy materials of construction.

• Available with FOUNDATION fieldbus functionality.

THE DUAL-SENSOR VORTEX FLOWMETER

• Safety Integrated Systems (SIS) - Ideal solution where redundant flow signals are required.

• Rosemount Reliability - Designed with same electronics, sensor, and meter body as the 8800D.

• Redundant Flow Measurement - Dual Vortex meter is constructed of two complete vortex meters: sensor, electronics, and shedder bar(1). The meters are welded together and flow calibrated to provide an accurate single flowmeter with two independent flow measurements.

• Available as flanged meter for 1/2 through 12-in. stainless steel and nickel alloy materials of construction.

(1) All 6-in. (150 mm) through 12-in. (300 mm) dual style vortex meters have a single shedder bar.



4

8800D MULTIVARIABLE VORTEX REDUCES INSTALLATION COSTS, SIMPLIFIES INSTALLATION, AND IMPROVES PERFORMANCE IN SATURATED STEAM

• MultiVariable Vortex DesignIncorporates temperature sensor into the vortex meter using the shedder bar as a thermowell, which keeps the vortex and temperature sensors isolated from process for easy verification and replacement.

• Temperature Compensated Capability for Saturated SteamCalculates density from measured process temperature and uses the calculated density to provide a temperature compensated mass flow.

• Increased performance in Saturated SteamPerformance in saturated steam is improved due to the fact that the electronics will be compensating for changes in the process temperature.

• Reduces Installed CostsMultiVariable Vortex eliminates the need for an external thermowell and temperature sensor.

• Output OptionsCan map independent variables to analog output, pulse output, or HART burst variables.

• Available with Flow Computer for additional functionalityIntegrate the MultiVariable Vortex with a pressure transmitter for full pressure and temperature compensation of superheated steam and various gases.

• Remote Mount ElectronicsAlso available with remote mounted electronics up to 75 ft. (23 m).

When you integrate the MultiVariable Vortex with a Rosemount Flow Computer, you get:

• Remote Communications

• Heat Calculations

• Remote Totalization

• Peak Demand Calculation

• Datalogging Capabilities

Please see Product Data Sheet 00813-0100-4005 for more information on the Rosemount Flow Computer.


ROSEMOUNT 8800D VORTEX FLOWMETER WITH FOUNDATION FIELDBUS

The software for the 8800D Flowmeter with FOUNDATION fieldbus permits remote testing and configuration using any FOUNDATION fieldbus-compliant host, such as the DeltaV system from Emerson Process Management.

Transducer Block

The transducer block calculates flow from sensor frequency. The calculation includes information about damping, shedding frequency, K-factor, process fluid, pipe ID, and diagnostics.

Resource Block

The resource block contains physical transmitter information, including available memory, manufacturer identification, device type, software tag, and unique identification.

Backup Link Active Scheduler (LAS)

The transmitter is classified as a device link master. A device link master can function as a Link Active Scheduler (LAS) if the current link master device fails or is removed from the segment.

The host or other configuration tool is used to download the schedule for the application to the link master device. In the absence of a primary link master, the transmitter will claim the LAS and provide permanent control for the H1 segment.

Diagnostics

The transmitter automatically performs continuous self-diagnostics. The user can perform on-line testing of the transmitter digital signal. Advanced simulation diagnostics are available. This enables remote verification of the electronics via a flow signal generator built into the electronics. The sensor strength value can be used to view the process flow signal and provide information regarding filter settings.

FOUNDATION Fieldbus Function Blocks

Analog Input

The AI function block processes the measurement and makes it available to other function blocks. The AI function block also allows filtering, alarming, and engineering unit changes.

The 8800D Flowmeter with FOUNDATION fieldbus comes standard with three AI function blocks (1 block for flow, 1 block for signal strength, and one block for future use with the MTA option).

Proportional/Integral/Derivative

The optional PID function block provides a sophisticated implementation of the universal PID algorithm. The PID function block features input for feed forward control, alarms on the process variable, and control deviation. The PID type (series or Instrument Society of America [ISA]) is user-selectable on the derivative filter.

Integrator

The standard integrator block is available for totalization of flow.

Setup

Basic setup requires connecting the transmitter to a fieldbus network or Field Communicator. The FOUNDATION fieldbus-compliant host will automatically establish communication with the device.

The Rosemount 8800D Flowmeter can be easily configured using the DeltaV system. User-configurable parameters include: tag, scaling and units, process fluid type, damping, fixed process density, pipe inside diameter (ID)(1), and fixed process temperature(1).

Tagging information can be entered into the transmitter to allow identification and a physical description. 32-character tags are provided for identification of the transmitter and each function block.

(1) Process temperature and pipe ID have known effects on the K-factor. The 8800D software automatically accounts for these effects by compensating the K-factor.

5



Specifications

The following specifications are for the Rosemount 8800D, Rosemount 8800DR, and Rosemount 8800DD, except where noted.

FUNCTIONAL SPECIFICATIONS

Process Fluids

Liquid, gas, and steam applications. Fluids must be homogeneous and single-phase.

Line Sizes

Wafer1/2, 1, 11/2, 2, 3, 4, 6, and 8 inches(DN 15, 25, 40, 50, 80, 100, 150, and 200)

Flanged and Dual-Sensor Style1/2, 1, 11/2, 2, 3, 4, 6, 8, 10, and 12 inches(DN 15, 25, 40, 50, 80, 100, 150, 200, 250, and 300)

Reducer1, 11/2, 2, 3, 4, 6, 8, 10, and 12 inches(DN 25, 40, 50, 80, 100, 150, 200, 250, and 300)

Pipe Schedules

Process piping Schedules 10, 40, 80, and 160.

NOTEThe appropriate bore diameter of the process piping must be entered using the Field Communicator or AMS Device Manager. Meters will be shipped from the factory at the Schedule 40 default value unless otherwise specified.

Measurable Flow Rates

Capable of processing signals from flow applications which meet the sizing requirements below.

To determine the appropriate flowmeter size for an application, process conditions must be within the Reynolds number and velocity limitations for the desired line size provided in Table 1, Table 2, and Table 3.

NOTEConsult your local sales representative to obtain a computer sizing program that describes in greater detail how to specify the correct flowmeter size for an application.

The Reynolds number equation shown below combines the effects of density (�), viscosity (�cp), pipe inside diameter (D), and flow velocity (V).

Table 1. Minimum Measurable Meter Reynolds Numbers

Meter Sizes(Inches / DN) Reynolds Number Limitations

1/2 through 4/15 through 1005000 minimum

6 through 12/150 through 300

Table 2. Minimum Measurable Meter Velocities(1)

(1) Velocities are referenced to schedule 40 pipe.

Feet per Second Meters per Second

Liquids(2)

(2) This minimum measurable meter velocity is based on default filter settings.

Gases(2)

The is the process fluid density at flowing conditions in lb/ft3 for ft/s and kg/m3 for m/s

Table 3. Maximum Measurable Meter Velocities(1)

(Use the smaller of the two values)

(1) Velocities are referenced to schedule 40 pipe.

Feet per Second Meters per Second

Liquids

Gases(2)

(2) Accuracy limitations for gas and steam for Dual-style meters (1/2-in. to 4-in.): max velocity of 100 ft/s (30.5 m/s).

The is the process fluid density at flowing conditions in lb/ft3 for ft/s and kg/m3 for m/s

RDVDcp------------=

36/ 54/

36/ 54/

90,000/ or 25 134,000/ or 7.690,000/ or 250 134,000/ or 76

6


7

Process Temperature Limits

Standard–40 to 450 °F (–40 to 232 °C)

Extended–330 to 800 °F (–200 to 427 °C)

MultiVariable (MTA option)

–40 to 800 °F (–40 to 427 °C)

• Use above 450 °F (232 °C) requires Extended Sensor

Output Signals

4–20 mA Digital HART Signal Superimposed on 4–20 mA signal

Optional Scalable Pulse Output0 to 10000 Hz; transistor switch closure with adjustable scaling via HART communications; capable of switching up to 30 Vdc, 120 mA maximum

Digital FOUNDATION fieldbus signal Completely digital output with FOUNDATION fieldbus communication (ITK 5.1 compliant).

Analog Output Adjustment

Engineering units and lower and upper range values are user-selected. Output is automatically scaled to provide 4 mA at the selected lower range value, 20 mA at the selected upper range value. No frequency input is required to adjust the range values.

Scalable Frequency Adjustment

The scalable pulse output can be set to a specific velocity, volume, or mass (i.e. 1 pulse = 1 lb). The scalable pulse output can also be scaled to a specific rate of volume, mass, or velocity (i.e. 100 Hz = 500 lb/hr).

Ambient Temperature Limits

Operating–58 to 185 °F (–50 to 85 °C)–4 to 185 °F (–20 to 85 °C) for flowmeters with local indicator

Storage –58 to 250 °F (–50 to 121 °C)–50 to 185 °F (–46 to 85 °C) for flowmeters with local indicator

Pressure Limits

Flange Style Meter Rated for ASME B16.5 (ANSI) Class 150, 300, 600, 900, and 1500, DIN PN 10, 16, 25, 40, 64, 100, and 160, and JIS 10K, 20K, and 40K

Reducer Style Meter Rated for ASME B16.5 (ANSI) Class 150, 300, 600, and 900, DIN PN 10, 16, 25, 40, 64, 100, and 160.

Dual Sensor Style MeterRated for ASME B16.5 (ANSI) Class 150, 300, 600, 900, and 1500, DIN PN 10, 16, 25, 40, 64, 100, and 160, and JIS 10K, 20K, and 40K

Wafer Style Meter Rated for ASME B16.5 (ANSI) Class 150, 300, and 600, DIN PN 10, 16, 25, 40, 64, and 100, and JIS 10K, 20K, and 40K

NOTE: All Wafer Style Meters are pressure rated and labeled at 1500 PSI / 10.34 MPa at 100 °F / 38 °C regardless of Alignment Ring Size code ordered.

Weld-End Style MeterW1 Welds to Schedule 10 mating pipe Max Working Pressure 720 psig (4.96 MPa-g)

W4 Welds to Schedule 40 mating pipe Max Working Pressure 1440 psig (9.93 MPa-g)

W8 Welds to Schedule 80 mating pipe Max Working Pressure 2160 psig (14.9 MPa-g)

W9 Welds to Schedule 160 mating pipe Max Working Pressure 3600 psig (24.8 Mpa-g)

NOTE:1-in. (25 mm), and 1.5-in. (40 mm) weld to Schedule 80 mating pipe

Power Supply

HART AnalogExternal power supply required. Flowmeter operates on 10.8 to 42 Vdc terminal voltage (with 250-ohm minimum load required for HART communications, 16.8 Vdc power supply is required)

FOUNDATION fieldbusExternal power supply required. Flowmeter operates on 9 to 32 Vdc, 18 mA maximum.



Power Consumption

One watt maximum

Load Limitations (HART Analog)

Maximum loop resistance is determined by the voltage level of the external power supply, as described by:

NOTEHART Communication requires a minimum loop resistance of 250 ohms.

Optional LCD Indicator

The optional LCD indicator is capable of displaying:

• Primary Variable

• Velocity Flow

• Volumetric Flow

• Mass Flow

• Percent of Range

• Analog Output (if applicable)

• Totalizer (Output Code “D” and “P” Only)

• Shedding Frequency

• Pulse Output Frequency (if applicable)

• Electronics Temperature (Output Code “D” and “P” Only)

• Process Temperature (MTA Option Only)

• Calculated Process Density (MTA Option Only)

If more than one item is selected, the display will scroll through all items selected.

Enclosure Rating

FM Type 4X; CSA Type 4X; IP66

Permanent Pressure Loss

The approximate permanent pressure loss (PPL) from the Rosemount 8800D flowmeter is calculated for each application in the Vortex sizing software available from your local Rosemount representative. The PPL is determined using the equation:

where:

Minimum Upstream Pressure (Liquids)

Flow metering conditions that would allow cavitation, the release of vapor from a liquid, should be avoided. This flow condition can be avoided by remaining within the proper flow range of the meter and by following appropriate system design.

For some liquid applications, incorporation of a back pressure valve should be considered. To prevent cavitation, the minimum upstream pressure should be:

Rmax = 41.7(Vps – 10.8)Vps = Power Supply Voltage (Volts)Rmax = Maximum Loop Resistance (Ohms)

Power Supply (Volts)

Lo

ad (

Oh

ms

)

OperatingRegion

1250

1000

500

010.8 42

PPL = Permanent Pressure loss (psi or kPa)

Where:

�f = Density at operating conditions (lb/ft3 or kg/m3)

Q = Actual volumetric flow rate (Gas = ft3/min or m3/hr; Liquid = gal/min or l/min)

D = Flowmeter bore diameter (in. or mm)

A = Constant depending on meter style, fluid type and flow units. Determined per following table:

Table 4. Determining the PPL

Meter Style

English Units SI Units

ALiquid AGas ALiquid AGas

8800DF/W 3.4 � 10-5 1.9 � 10-3 0.425 118

8800DR 3.91 � 10-5 2.19 � 10-3 0.489 136

8800DD(1)

(1) For all 6-in. thru 12-in. line sizes A is the same for 8800DD and 8800DF

6.12 � 10-5 3.42 � 10-3 0.765 212

P = 2.9P + 1.3pv or P = 2.9P + pv + 0.5 psia (3.45 kPa) (use the smaller of the two results)

P = Line pressure five pipe diameters downstream of the meter (psia or kPa abs)

P = Pressure loss across the meter (psi or kPa)pv = Liquid vapor pressure at operating conditions

(psia or kPa abs)

PPLA f Q2

D4------------------------------=

8


Failure Mode Alarm

HART AnalogIf self-diagnostics detect a gross flowmeter failure, the analog signal will be driven to the values below:

High or low alarm signal is user-selectable through the fail mode alarm jumper on the electronics. NAMUR-compliant alarm limits are available through the C4 or CN Option. Alarm type is field configurable also.

FOUNDATION fieldbusThe AI block allows the user to configure the alarm to HI-HI, HI, LO, or LO-LO with a variety of priority levels.

Saturation Output Values

When the operating flow is outside the range points, the analog output continues to track the operating flow until reaching the saturation value listed below; the output does not exceed the listed saturation value regardless of the operating flow. The NAMUR-Compliant Saturation Values are available through the C4 or CN option. Saturation type is field configurable.

Damping

Flow Damping adjustable between 0.2 and 255 seconds.

Process Temperature Damping adjustable between 0.4 and 32.0 seconds (MTA Option Only).

Response Time

Three vortex shedding cycles or 300 ms, whichever is greater, maximum required to reach 63.2% of actual input with the minimum damping (0.2 seconds).

Turn-on Time

HART AnalogLess than four (4) seconds plus the response time to rated accuracy from power up (less than 7 seconds with the MTA Option).

FOUNDATION fieldbusPerformance within specifications no greater than 10.0 seconds after power is applied.

Transient Protection

The optional transient terminal block prevents damage to the flowmeter from transients induced by lightning, welding, heavy electrical equipment, or switch gears. The transient protection electronics are located in the terminal block.

The transient terminal block meets the following specifications:ASME B16.5 (ANSI)/IEEE C62.41 - 1980 (IEEE 587) Categories A, B 3 kA crest (8 � 20 s)6 kV crest (1.2 � 50 s)6 kV/0.5 kA (0.5 s, 100 kHz, ring wave)

Security Lockout

When the security lockout jumper is enabled, the electronics will not allow you to modify parameters that affect flowmeter output.

Output Testing

Current SourceFlowmeter may be commanded to set the current to a specified value between 4 and 20 mA.

Frequency SourceFlowmeter may be commanded to set the frequency to a specified value between 0 and 10000 Hz.

Low Flow Cutoff

Adjustable over entire flow range. Below selected value, output is driven to 4 mA and zero pulse output frequency.

Humidity Limits

Operates in 0–95% relative humidity under noncondensing conditions (tested to IEC 60770, Section 6.2.11).

Overrange Capability

HART AnalogAnalog signal output continues to 105 percent of span, then remains constant with increasing flow. The digital and pulse outputs will continue to indicate flow up to the upper sensor limit of the flowmeter and a maximum pulse output frequency of 10400 Hz.

Low 3.75High 22.6NAMUR Low 3.60NAMUR High 22.6

Low 3.9High 20.8NAMUR Low 3.8NAMUR High 20.5

9



FOUNDATION fieldbusFor liquid process fluid type, the transducer block digital output will continue to a nominal value of 25 ft/s. After that, the status associated with the transducer block output will go to UNCERTAIN. Above a nominal value of 30 ft/s, the status will go to BAD.

For gas/steam service, the transducer block digital output will continue to a nominal value of 220 ft/s for 0.5 and 1.0-in. line sizes and a nominal value of 250 ft/s for 1.5–12-in. line sizes. After that, the status associated with the transducer block output will go to UNCERTAIN. Above a nominal value of 300 ft/s for all line sizes, the status will go to BAD.

Flow Calibration

Meter bodies are flow-calibrated and assigned a unique calibration factor (K-factor) at the factory. The calibration factor is entered into the electronics, enabling interchangeability of electronics and/or sensors without calculations or compromise in accuracy of the calibrated meter body.

Status (FOUNDATION fieldbus only)

If self-diagnostics detect a transmitter failure, the status of the measurement will inform the control system. Status may also set the PID output to a safe value.

Schedule Entries (FOUNDATION fieldbus only)

Six (6)

Links (FOUNDATION fieldbus only)

Twelve (12)

Virtual Communications Relationships (VCRs) (FOUNDATION fieldbus only)

Two (2) predefined (F6, F7)Four (4) configured (see Table 5)

Table 5. Block Information

Block Base IndexExecution Time (Milliseconds)

Resource (RB) 300 —

Transducer (TB) 400 —

Analog Input (AI) 1,000 20

Proportional/Integral/Derivative (PID)

10,000 30

Integrator (INT) 12,000 20

10


Typical Flow Ranges

Table 6 - Table 12 show typical flow ranges for some common process fluids with default filter settings. Consult your local sales representative to obtain a computer sizing program that describes in greater detail the flow range for an application.

Table 6. Typical pipe velocity ranges for 8800D and 8800DR(1)

(1) Table 6 is a reference of pipe velocities that can be measured for the standard Rosemount 8800D and the reducer Rosemount 8800DR Vortex Meters. It does not consider density limitations, as described in tables 2 and 3. Velocities are referenced in schedule 40 pipe.

Process Line Size Liquid Velocity Ranges Gas Velocity Ranges

(Inches/ DN) Vortex Meter (2)

(2) Velocity range of the Rosemount 8800DW is the same as Rosemount 8800DF.

(ft/s) (m/s) (ft/s) (m/s)

0.5/ 15 8800DF005 0.70 to 25.0 0.21 to 7.6 6.50 to 250.0 1.98 to 76.21/ 25 8800DF010 0.70 to 25.0 0.21 to 7.6 6.50 to 250.0 1.98 to 76.2

8800DR010 0.25 to 8.8 0.08 to 2.7 2.29 to 87.9 0.70 to 26.81.5/ 40 8800DF015 0.70 to 25.0 0.21 to 7.6 6.50 to 250.0 1.98 to 76.2

8800DR015 0.30 to 10.6 0.09 to 3.2 2.76 to 106.1 0.84 to 32.32/ 50 8800DF020 0.70 to 25.0 0.21 to 7.6 6.50 to 250.0 1.98 to 76.2







8800DR120 0.63 to 17.6 0.19 to 5.4 4.58 to 176.1 1.40 to 53.7

11



Table 7. Water Flow Rate Limits for the Rosemount 8800D and 8800DR(1)

Process Line Size

Vortex Meter (2)

Minimum and Maximum Measurable Water Flow Rates*

(Inches/ DN) Gallons/Minute Cubic Meters/Hour

0.5/ 15 8800DF005 1.76 to 23.7 0.40 to 5.4

1/ 25 8800DF010 2.96 to 67.3 0.67 to 15.3

8800DR010 1.76 to 23.7 0.40 to 5.4

1.5/ 40 8800DF015 4.83 to 158 1.10 to 35.9

8800DR015 2.96 to 67.3 0.67 to 15.3

2/ 50 8800DF020 7.96 to 261 1.81 to 59.4

8800DR020 4.83 to 158.0 1.10 to 35.9

3/ 80 8800DF030 17.5 to 576 4.00 to 130

8800DR030 7.96 to 261.0 1.81 to 59.3

4/ 100 8800DF040 30.2 to 992 6.86 to 225

8800DR040 17.5 to 576 4.00 to 130

6/ 150 8800DF060 68.5 to 2251 15.6 to 511

8800DR060 30.2 to 992 6.86 to 225

8/ 200 8800DF080 119 to 3898 27.0 to 885

8800DR080 68.5 to 2251 15.6 to 511

10/ 250 8800DF100 231 to 6144 52.2 to 1395

8800DR100 119 to 3898 27.0 to 885

12/ 300 8800DF120 391 to 8813 88.8 to 2002

8800DR120 231 to 6144 52.2 to 1395

*Conditions: 77 °F (25 °C) and 14.7 psia (1.01 bar absolute)

(1) Table 7 is a reference of flow rates that can be measured for the standard Rosemount 8800D and the reducer 8800DR Vortex Meters. It does not consider density limitations, as described in tables 2 and 3.

(2) Velocity range of the 8800DW is the same as 8800DF.

Table 8. Air Flow Rate Limits at 59 °F (15 °C)

Process Pressure

Flow Rate

Limits

Minimum and Maximum Air Flow Ratesfor line sizes 1/2-in./DN 15 through 1-in./DN 25

1/2-in./DN 15 1-in./DN 25

Rosemount 8800D Rosemount 8800DR Rosemount 8800D Rosemount 8800DR

ACFM ACMH ACFM ACMH ACFM ACMH ACFM ACMH

0 psig(0 bar G)

maxmin

27.93.86

47.36.56

Not Available

Not Available

79.27.81

13413.3

27.93.86

47.36.56

50 psig(3,45 bar G)

maxmin

27.91.31

47.32.22

Not Available

Not Available

79.23.72

1346.32

27.91.31

47.32.22

100 psig(6,89 bar G)

maxmin

27.90.98

47.31.66

Not Available

Not Available

79.22.80

1344.75

27.90.98

47.31.66


maxmin

27.90.82

47.31.41

Not Available

Not Available

79.22.34

1343.98

27.90.82

47.31.41


maxmin

27.90.82

47.31.41

Not Available

Not Available

79.22.34

1343.98

27.90.82

47.31.41


maxmin

27.90.82

47.31.41

Not Available

Not Available

79.22.34

1343.98

27.90.82

47.31.41


maxmin

25.70.82

43.91.41

Not Available

Not Available

73.02.34

1243.98

25.70.82

43.91.41


maxmin

23.00.82

39.41.41

Not Available

Not Available

66.02.34

1123.98

23.00.82

39.41.41

12



Process Pressure

Flow Rate

Limits

Minimum and Maximum Air Flow Ratesfor line sizes 11/2-in./DN 40 through 2-in./DN 50

1½-in./DN 40 2-in./DN 50



0 psig(0 bar G)

maxmin

21218.4

36031.2

79.27.81

13413.3

34930.3

59351.5

21218.4

36031.2

50 psig(3,45 bar G)

maxmin

2128.76

36014.9

79.23.72

1346.32

34914.5

59324.6

2128.76

36014.9


maxmin

2126.58

36011.2

79.22.80

1344.75

34910.8

59318.3

2126.58

36011.2


maxmin

2125.51

3609.36

79.22.34

1343.98

3499.09

59315.4

2125.51

3609.36


maxmin

2125.51

3609.36

79.22.34

1343.98

3499.09

59315.4

2125.51

3609.36


maxmin

1985.51

3379.36

79.22.34

1343.98

3269.09

55415.4

1985.51

3379.36


maxmin

1725.51

2939.36

73.02.34

1243.98

2849.09

48315.4

1725.51

2939.36


maxmin

1545.51

2629.36

66.02.34

1123.98

2549.09

43215.4

1545.51

2629.36


Process Pressure

Flow Rate

Limits

Minimum and Maximum Air Flow Ratesfor line sizes 3-in./DN 80 through 4-in./DN 100

3-in./DN 80 4-in./DN 100



0 psig(0 bar G)

maxmin

77066.8

1308114

34930.3

59351.5

1326115

2253195

77066.8

1308114

50 psig(3,45 bar G)

maxmin

77031.8

130854.1

34914.5

59324.6

132654.8

225393.2

77031.8

130854.1


maxmin

77023.9

130840.6

34910.8

59318.3

132641.1

225369.8

77023.9

130840.6


maxmin

77020.0

130834.0

3499.09

59315.4

132634.5

225358.6

77020.0

130834.0


maxmin

77020.0

130834.0

3499.09

59315.4

132634.5

225358.6

77020.0

130834.0


maxmin

71820.0

122034.0

3269.09

55415.4

123734.5

210258.6

71820.0

122034.0


maxmin

62520.0

106234.0

2849.09

48315.4

107634.5

182858.6

62520.0

106234.0


maxmin

56020.0

95134.0

2549.09

43215.4

96434.5

163858.6

56020.0

95134.0

13



14

NOTESThe Rosemount 8800D measures the volumetric flow under operating conditions (i.e. the actual volume at the operating pressure and temperature–acfm or acmh), as shown above. However, gas volumes are strongly dependent on pressure and temperature. Therefore, gas quantities are typically stated in standard or normal conditions (e.g. SCFM or NCMH). (Standard conditions are typically 59 °F and 14.7 psia. Normal conditions are typically 0 °C and 1 bar abs.) The flow rate limits in standard conditions are found using the equations below: Standard Flow Rate = Actual Flow Rate X Density Ratio Density Ratio = Density at Actual (Operating) Conditions / Density at Standard Conditions


Process Pressure

Flow Rate

Limits


6-in./DN 150 8-in./DN 200



0 psig(0 bar G)

maxmin

3009261

5112443

1326115

2253195

5211452

8853768

3009261

5112443

50 psig(3,45 bar G)

maxmin

3009124

5112211

132654.8

225393.2

5211215

8853365

3009124

5112211


maxmin

300993.3

5112159

132641.1

225369.8

5211162

8853276

300993.3

5112159


maxmin

300978.2

5112133

132634.5

225358.6

5211135

8853229

300978.2

5112133


maxmin

300978.2

5112133

132634.5

225358.6

5211135

8853229

300978.2

5112133


maxmin

280778.2

4769133

123734.5

210258.6

4862135

8260229

280778.2

4769133


maxmin

244278.2

4149133

107634.5

182858.6

4228136

7183229

244278.2

4149133


maxmin

218878.2

3717133

96434.5

163858.6

3789136

6437229

218878.2

3717133


Process Pressure

Flow Rate

Limits


10-in./DN 250 12-in./DN 300



0 psig(0 bar G)

maxmin

8214712.9

139561211

5211452

8853768

117811022

200161736

8214712.9

139561211

50 psig(3,45 bar G)

maxmin

8214339.5

13956577

5211215

8853365

11781486.9

20016827

8214339.5

13956577


maxmin

8214254.7

13956433

5211162

8853276

11781365.4

20016621

8214254.7

13956433


maxmin

8214213.6

13956363

5211135

8853229

11781306.3

20016520

8214213.6

13956363


maxmin

8214213.6

13956363

5211135

8853229

11781306.3

20016520

8214213.6

13956363


maxmin

7664213.6

13021363

4862135

8260229

10992306.3

18675520

7664213.6

13021363


maxmin

6664213.6

11322363

4228136

7183229

9559306.3

16241520

6664213.6

11322363


maxmin

5972213.6

10146363

3789136

6437229

8565306.3

14552520

5972213.6

10146363


Table 13. Saturated Steam Flow Rate Limits (Assumes Steam Quality is 100%)

Process Pressure

Flow Rate Limits

Minimum and Maximum Saturated Steam Flow Rates for line sizes 1/2-in./DN 15 through 1-in./DN 25

½-in./DN 15 1-in./DN 25


lb/hr kg/hr lb/hr kg/hr lb/hr kg/hr lb/hr kg/hr

15 psig(1,03 bar G)

maxmin

12012.8

54.65.81

Not Available

Not Available

34234.8

15515.8

12012.8

54.65.81

25 psig(1,72 bar G)

maxmin

15814.0

71.76.35

Not Available

Not Available

44939.9

20318.1

15814.0

71.76.35

50 psig(3,45 bar G)

maxmin

25017.6

1138.00

Not Available

Not Available

71150.1

32222.7

25017.6

1138.00


maxmin

42923.1

19410.5

Not Available

Not Available

122165.7

55429.8

42923.1

19410.5


maxmin

60627.4

27512.5

Not Available

Not Available

172478.1

78235.4

60627.4

27512.5


maxmin

78231.2

35414.1

Not Available

Not Available

222588.7

100940.2

78231.2

35414.1


maxmin

113537.6

51517.0

Not Available

Not Available

3229107

146448.5

113537.6

51517.0


maxmin

149244.1

67620.0

Not Available

Not Available

4244125

192556.7

149244.1

67620.0


maxmin

185554.8

84124.9

Not Available

Not Available

5277156

239370.7

185554.8

84124.9


Process Pressure

Flow Rate Limits

Minimum and Maximum Saturated Steam Flow Rates for line sizes 11/2-in./DN 40 through 2-in./DN 50

1½-in./DN 40 2-in./DN 50



15 psig(1,03 bar G)

maxmin

91782.0

41637.2

34234.8

15515.8

1511135

68561.2

91782.0

41637.2

25 psig(1,72 bar G)

maxmin

120493.9

54642.6

44939.9

20318.1

1983155

89970.2

120493.9

54642.6

50 psig(3,45 bar G)

maxmin

1904118

86453.4

71150.1

32222.7

3138195

142388.3

1904118

86453.4


maxmin

3270155

148370.1

122165.7

55429.8

5389255

2444116

3270155

148370.1


maxmin

4616184

209483.2

172478.1

78235.4

7609303

3451137

4616184

209483.2


maxmin

5956209

270294.5

222588.7

100940.2

9818344

4453156

5956209

270294.5


maxmin

8644252

3921114

3229107

146448.5

14248415

6463189

8644252

3921114


maxmin

11362295

5154134

4244125

192556.7

18727487

8494221

11362295

5154134


maxmin

14126367

6407167

5277156

239370.7

23284605

10561274

14126367

6407167

15




Process Pressure

Flow Rate Limits

Minimum and Maximum Saturated Steam Flow Rates for line sizes 3-in./DN 80 through 4-in./DN 100

3-in./DN 80 4-in./DN 100



15 psig(1,03 bar G)

maxmin

3330298

1510135

1511135

68561.2

5734513

2601233

3330298

1510135

25 psig(1,72 bar G)

maxmin

4370341

1982155

1983155

89970.2

7526587

3414267

4370341

1982155

50 psig(3,45 bar G)

maxmin

6914429

3136195

3138195

142388.3

11905739

5400335

6914429

3136195


maxmin

11874562

5386255

5389255

2444116

20448968

9275439

11874562

5386255


maxmin

16763668

7603303

7609303

3451137

288661150

13093522

16763668

7603303


maxmin

21630759

9811344

9818344

4453156

372471307

16895593

21630759

9811344


maxmin

31389914

14237415

14248415

6463189

540521574

24517714

31389914

14237415


maxmin

412581073

18714487

18727487

8494221

710471847

32226838

412581073

18714487


maxmin

512971334

23267605

23284605

10561274

883342297

400681042

512971334

23267605


Process Pressure

Flow Rate Limits


6-in./DN 150 8-in./DN 200



15 psig(1,03 bar G)

maxmin

130131163

5903528

5734513

2601233

225342015

10221914

130131163

5903528

25 psig(1,72 bar G)

maxmin

170801333

7747605

7526587

3414267

295752308

134151047

170801333

7747605

50 psig(3,45 bar G)

maxmin

270191676

12255760

11905739

5400335

467872903

212221317

270191676

12255760


maxmin

464052197

21049996

20448968

9275439

803563804

364491725

464052197

21049996


maxmin

656112610

297611184

288661150

13093522

1134404520

514552050

656112610

297611184


maxmin

845302965

383421345

372471307

16895593

1463755134

663952329

845302965

383421345


maxmin

1226663572

556401620

540521574

24517714

2124116185

963482805

1226663572

556401620


maxmin

1612364192

731351901

710471847

32226838

2792007259

1266433293

1612364192

731351901


maxmin

2004685212

909312364

883342297

400681042

3471349025

1574574094

2004685212

909312364

16



Process Pressure

Flow Rate Limits


10-in./DN 250 12-in./DN 300



15 psig(1,03 bar G)

maxmin

355193175

161111440

225342015

10221914

509944554

231302066

355193175

161111440

25 psig(1,72 bar G)

maxmin

466184570

211462073

295752308

134151047

668625218

303282367

466184570

211462073

50 psig(3,45 bar G)

maxmin

737484575

334522075

467872903

212221317

1057746562

479782976

737484575

334522075


maxmin

1266605996

574522720

803563804

364491725

1816638600

824013901

1266605996

574522720


maxmin

1788087125

811063232

1134404520

514552050

25645710218

1163274635

1788087125

811063232


maxmin

2307228092

1046543670

1463755134

663952329

33091511607

1501015265

2307228092

1046543670


maxmin

3348109749

1518674422

2124116185

963482805

48020313983

2178166343

3348109749

1518674422


maxmin

44008511442

1996195190

2792007259

1266433293

63119516411

2863057444

44008511442

1996195190


maxmin

54716514226

2481906453

3471349025

1574574094

78477520404

3559689255

54716514226

2481906453

17



18

PERFORMANCE SPECIFICATIONSThe following performance specifications are for all Rosemount models except where noted. Digital performance specifications applicable to both Digital HART and FOUNDATION fieldbus output.

Flow Accuracy

Includes linearity, hysteresis, and repeatability.

Liquids - for Reynolds Numbers over 20000

Digital and Pulse Output±0.65% of rate

Note: The accuracy for the 8800DR, line sizes 6 to 12-in. (150 to 300mm), is ±1.0% of rate.

Analog OutputSame as pulse output plus an additional 0.025% of span

Gas and Steam - for Reynolds Numbers over 15,000

Digital and Pulse Output±1.0% of rate

Note: The accuracy for the 8800DR, line sizes 6 to 12-in. (150 to 300mm), is ±1.35% of rate.


Accuracy limitations for gas and steam:

For 1/2 and 1-in. (DN 15 and DN 25): max velocity of 220 ft/s (67.06 m/s)

For 1/2 to 4-in. (DN 15 to DN 200) Dual-style meters: max velocity of 100 ft/s (30.5 m/s)

NOTEAs the meter Reynolds Numbers decreases below the stated limit to 10,000 the accuracy error band will increase linearly to +/-2.0%. For Reynolds Numbers down to 5,000 the accuracy error band will increase linearly from +/-2.0% to +/-6.0%.

Process Temperature Accuracy

2.2 °F (1.2 °C) or 0.4% of reading (in °C), whichever is greater.

NOTEFor remote mount installations, add ±0.018 °F/ft. (±0.03 °C/m) of uncertainty to the temperature measurement.

Mass Flow Accuracy for Temperature Compensated Mass Flow

Digital and Pulse Output± 2.0% of rate (Nominal)

Nominal conditions include temperature variation in saturation and superheat at 150 psig (10 bar-g) and above.

For pressure below 150 psig (10 bar-g), add 0.08% of uncertainty for every 15 psi (1 bar) below 150 psig (10 bar-g).


Repeatability

± 0.1% of actual flow rate

Stability

± 0.1% of rate over one year

Process Temperature Effect

Automatic K-factor correction with user-entered process temperature.

Table 18 indicates the percent change in K-factor per 100 °F (55.5 °C) in process temperature from reference temperature of 77 °F (25 °C).

Ambient Temperature Effect

Digital and Pulse OutputsNo effect

Analog Output±0.1% of span from –58 to 185 °F (–50 to 85 °C)

Table 18. Process Temperature Effect

MaterialPercent Change in

K-Factor per 100 °F (55.5 °C)

316L @ < 77 °F (25 °C) + 0.23316L @ > 77 °F (25 °C) - 0.27

Nickel Alloy C < 77 °F (25 °C) + 0.22Nickel Alloy C > 77 °F (25 °C) - 0.22


Vibration Effect

An output with no process flow may be detected if sufficiently high vibration is present.

The meter design will minimize this effect, and the factory settings for signal processing are selected to eliminate these errors for most applications.

If an output error at zero flow is still detected, it can be eliminated by adjusting the low flow cutoff, trigger level, or low-pass filter.

As the process begins to flow through the meter, most vibration effects are quickly overcome by the flow signal.

Vibration Specifications

Integral Aluminum Housings, Remote Aluminum Housings, and Remote SST HousingsAt or near the minimum liquid flow rate in a normal pipe mounted installation, the maximum vibration should be 0.087-in. (2,21 mm) double amplitude displacement or 1 g acceleration, whichever is smaller. At or near the minimum gas flow rate in a normal pipe mounted installation, the maximum vibration should be 0.043-in. (1,09 mm) double amplitude displacement or 1/2 g acceleration, whichever is smaller.

Integral SST HousingAt or near the minimum liquid flow rate in a normal pipe mounted installation, the maximum vibration should be 0.044-in. (1,11 mm) double amplitude displacement or 1/3 g acceleration, whichever is smaller. At or near the minimum gas flow rate in a normal pipe mounted installation, the maximum vibration should be 0.022-in. (0,55 mm) double amplitude displacement or 1/6 g acceleration, whichever is smaller.

Mounting Position Effect

Meter will meet accuracy specifications when mounted in horizontal, vertical, or inclined pipelines. Best practice for mounting in a horizontal pipe is to orient the shedder bar in the horizontal plane. This will prevent solids in liquid applications and liquid in gas/steam applications from disrupting the shedding frequency.

EMI/RFI Effect

Meets EMC requirements to EU Directive 2004/108/EC.

HART AnalogOutput error less than ±0.025% of span with twisted pair from 80-1000 MHz for radiated field strength of 10 V/m. Tested per EN61326.

FOUNDATION fieldbus and Digital HARTNo affect on the values that are being given if using HART digital signal or FOUNDATION fieldbus. Tested per EN61326.

Magnetic-Field Interference

HART AnalogOutput error less than ±0.025% of span at 30 A/m (rms).

FOUNDATION fieldbusNo effect on digital output accuracy at 30 A/m (rms). Tested per EN 61326.

Series Mode Noise Rejection

HART AnalogOutput error less than ±0.025% of span at 1 V rms, 60 Hz.

FOUNDATION fieldbusNo effect on digital output accuracy at 1 V rms, 60 Hz.

Common Mode Noise Rejection

HART AnalogOutput error less than ±0.025% of span at 30 V rms, 60 Hz.

FOUNDATION fieldbusNo effect on digital output accuracy at 250 V rms, 60 Hz.

Power Supply Effect

HART AnalogLess than 0.005% of span per volt

FOUNDATION fieldbusNo effect on accuracy.

19



PHYSICAL SPECIFICATIONS

NACE Compliance

Materials of Construction meet NACE material recommendations per MR0175/ISO15156 for use in H2S containing environments in oil field production. Materials of construction also meet NACE recommendations per MR0103-2003 for corrosive petroleum refining environments. MR0103 compliance requires Q25 option in model code.

NOTE:Certificate of compliance for MR0175/ISO15156 requires Q15 as a separate line item.

Electrical Connections

1/2 –14 NPT, PG 13.5, or M20 � 1.5 conduit threads; screw terminals provided for 4–20 mA and pulse output connections; communicator connections permanently fixed to terminal block.

Non-Wetted Materials

HousingLow-copper aluminum (FM Type 4X, CSA Type 4X, IP66)Optional SST housing

PaintPolyurethane

Cover O-ringsBuna-N

Flanges316/316L lap joint

Temperature Sensor (MTA Option)Type-N Thermocouple

Process-Wetted Materials

Meter Body316L wrought stainless and CF-3M cast stainless or N06022 wrought Nickel Alloy and CW2M cast Nickel Alloy. Other material grades available. Consult factory for other materials of construction.

Flanges 316/316L stainless steelNickel Alloy N06022 Weld Neck

CollarsNickel Alloy N06022316/316L Stainless Steel

Process Connections

Mounts between the following flange configurations:

ASME B16.5 (ANSI): Class 150, 300, 600, 900, 1500

DIN: PN 10, 16, 25, 40, 64, 100, 160

JIS: 10K, 20K, and 40K

Weld-end: Schedule 10, Schedule 40, Schedule 80, Schedule 160

Mounting

Integral (Standard)Electronics are mounted on meter body.

Remote (Optional)Electronics may be mounted remote from the meter body. Interconnecting coaxial cable available in nonadjustable 10, 20, and 30 ft (3,0, 6,1, and 9,1 m) lengths. Consult factory for non-standard lengths up to 75 ft (22,9 m). Remote mounting hardware includes a pipe mount bracket with one u-bolt.

Surface Finish of Flanges and CollarsStandard: To the requirements of the applicable flange standard.Smooth: 63 to 125 inches(1.6 to 3.1 meters) Ra roughness

20


21

Temperature Limitations for Integral MountingThe maximum process temperature for integral mount electronics is dependent on the ambient temperature where the meter is installed. The electronics must not exceed 185°F (85°C). The following is for reference, please note that the pipe was insulated with 3 inches of ceramic fiber insulator.

Pipe Length Requirements

The vortex meter may be installed with a minimum of ten diameters (D) of straight pipe length upstream and five diameters (D) of straight pipe length downstream.

Rated Accuracy is based on the number of pipe diameter from an upstream disturbance. No K-factor correction is required if the meter is installed with 35 D upstream and 10 D downstream. The value of the K-factor may shift up to 0.5% when the upstream straight pipe length is between 10D and 35D. Please see Technical Data Sheet (00816-0100-3250) on Installation Effects for optional K-factor corrections. This effect can be corrected in the electronics. Tagging

The flowmeter will be tagged at no charge, according to customer requirements. All tags are stainless steel. The standard tag is permanently attached to the flowmeter. Character height is 1/16-in. (1,6 mm). A wired-on tag is available on request. Wire on tags can contain five lines with up to 28 characters per line.

Flow Calibration Information

Flowmeter calibration and configuration information is provided with every flowmeter. For a certified copy of flow calibration data, Option Q4 must be ordered in the model number.

Figure 1. Rosemount 8800 Vortex Flowmeter Ambient/process temperature limits

Shows combinations of ambient and process temperatures needed to remain at or below 185°F (85°C) housing

temperature

200 (93)

180 (82)

160 (71)

140 (60)

120 (49)

100 (38)

80 (27)

60 (16)

0

200

(93)

300

(149

)

400

(204

)

500

(260

)

600

(316

)

700

(371

)

800

(427

)

900

(482

)

1000

(53

8)

100

(38)

Am

bie

nt

Tem

per

atu

re °

F (

°C)

Process Temperature °F (°C)

185°F Housing Temperature Limit

Meter and pipe insulated with 3 inches of ceramic fiber insulation. Horizontal Pipe and Vertical meter position.



22

Product Certifications

Approved Manufacturing LocationsRosemount Inc. — Eden Prairie, Minnesota, USA

Emerson Process Management BV - Ede, The Netherlands

Emerson Process Management Flow Technologies Company, Ltd - Nanjing, Jiangsu Province, P.R. China

EUROPEAN DIRECTIVE INFORMATIONThe CE Declaration of Conformity for all applicable European directives for this product can be found on our website at www.rosemount.com. A hard copy may be obtained by contacting our local sales office.

ATEX DirectiveRosemount Inc. complies with the ATEX Directive.

Flameproof enclosure EEx d protection type in accordance with EN50018

• Transmitters with Flameproof enclosure type protection shall only be opened when power is removed.

• Closing of entries in the device must be carried out using the appropriate EEx d metal cable gland or metal blanking plug.

• Do not exceed the energy level, which is stated on the approval label.

Type n protection type in accordance with EN60079-15Closing of entries in the device must be carried out using the appropriate EExe or EExn metal cable gland and metal blanking plug or any appropriate ATEX approved cable gland and blanking plug with IP66 rating certified by an EU approved certification body.

EUROPEAN PRESSURE EQUIPMENT DIRECTIVE (PED)

Rosemount 8800 Vortex Flowmeter Line Size 40 mm to 300 mmCertificate Number PED-H-100

0575

Module H Conformity Assessment

Mandatory CE-marking for flowmeters in accordance with Article 15 of the PED can be found on the flowtube body.

Flowmeter categories I – IV, use module H for conformity assessment procedures.

Rosemount 8800 Vortex Flowmeter Line Size 15 mm and 25 mm

Sound Engineering PracticeFlowmeters that are SEP are outside the scope of PED and cannot be marked for compliance with PED.

HAZARDOUS LOCATION CERTIFICATIONS

Rosemount 8800D with HART Protocol

North American Certifications

Factory Mutual (FM)E5 Explosion-proof for Class I, Division 1, Groups B, C, and D;

Dust Ignition-proof for Class II/III, Division 1, Groups E, F, and G; Temp Code T6 (-50°C Ta 70°C)Factory SealedEnclosure Type 4X.

I5 Intrinsically safe for use in Class I, II, III Division 1, Groups A, B, C, D, E, F, G; Class I, Zone 0, AEx ia IIC T4Non-incendive for Class I, Division 2, Groups A, B, C, and D. NIFW (Non-incendive Field Wiring) when installed per Rosemount Drawing 08800-0112T4 (-50°C to 70°C)Enclosure Type 4X.

K5 E5 and I5 Combination

Canadian Standards Association (CSA)E6 Dust Ignition-proof for Class II and Class III, Division 1,

Groups E, F, and G;Class I, Zone 1, Ex d[ia] IIC CSA 06.1674267T6 (-50°C to 70°C)Factory SealedSingle Seal.Enclosure Type 4X.

I6 Intrinsically safe for use in Class I, II, III Division 1, Groups A, B, C, D, E, F, G;Non-incendive for Class I, Division 2, Groups A, B, C and DT4 (-50°C to 70°C)Single Seal.Enclosure Type 4X.

K6 E6 and I6 Combination

Combination CertificationsKB E5, I5, E6, and I6 Combination


European Certifications

ATEX Intrinsic Safety I1 Certification No. Baseefa05ATEX0084X

ATEX Marking II 1 GEEx ia IIC T5 (-60°C Ta 40°C)EEx ia IIC T4 (-60°C Ta 70°C)

Input Parameters:Ui = 30 VdcIi

(1) = 185 mAPi

(1) = 1.0 WCi = 0 FLi = 0.97 mH

0575

SPECIAL CONDITIONSWhen fitted with 90V transient suppressors (T1 Option), the equipment is not capable of passing the 500V isolation test. This must be taken into account upon installation.

ATEX Type N CertificationN1 Certification No. Baseefa05ATEX0085X

ATEX Marking II 3 GEEx nAnL II T5 (-40°C Ta 70°C)Input Parameters:

Ui = 42 V dc MaxCi = 0 FLi = 0.97 mH


ATEX Flameproof CertificationE1 Certification No. KEMA99ATEX3852X

ATEX Marking Remote Mount:Transmitter: II 2(1) G

EEx d [ia] IIC T6 (-50°C Ta 70°C)Meter Body: II 1 G

EEx ia IIC T6 (-50°C Ta 70°C)ATEX Marking Integral Mount: II 1/2 G

EEx d [ia] IIC T6 (-50°C Ta 70°C) 0575

V = 42 Vdc MaxUm = 250V

SPECIAL CONDITIONSWhen the equipment is installed, precautions must be taken to ensure, taking into account the effect of the fluid temperature, that the ambient temperature of the electrical parts of the equipment is comprised between -50°C and 70°C. The remote mounted sensor may only be connected to the transmitter with the associated cable, supplied by the manufacturer.

ATEX Dust Certification ND Certification No. Baseefa05ATEX0086

ATEX Marking Ex tD A20 IP66 T90°C

(-20°C Ta 70°C)

Ui = 42 Vdc

0575

K1 E1, I1, N1 and ND Combination

(1) Total for transmitter

23



International IECEx Certifications

Intrinsic SafetyI7 Certification No. IECEx BAS05.0028X

Ex ia IIC T5 (-60°C Ta 40°C)

Ex ia IIC T4 (-60°C Ta 70°C)Input Parameters:

Ui = 30 VdcIi = 185 mAPi = 1.0 WCi = 0 FLi = 0.97 mH


Type N CertificationN7 Certification No. IECEx BAS05.0029X

Ex nC IIC T5 (-40°C Ta 70°C)

Ui = 42 V dc


Flameproof CertificationE7 Certification No. IECEx KEM05.0017X

Marking Remote Mount:Transmitter: Ex d [ia] IIC T6 (-50°C Ta 70°C)Meter Body: Ex ia IIC T6 (-50°C Ta 70°C)

Marking Integral Mount: Ex d [ia] IIC T6(-50°C Ta 70°C)


SPECIAL CONDITIONSWhen the equipment is installed, particular precautions must be taken to ensure, taking into account the effect of the process fluid temperature, that the ambient temperature of the electrical parts of the equipment is comprised between -50°C and 70°C.The remote mounted sensor shall only be connected to the transmitter with the associated cable, supplied by the manufacturer.

K7 E7, I7, and N7 Combination

Chinese Certifications (NEPSI)

Flameproof CertificationE3 Certification No. GYJ071327X

Ex d [ia] IIC T6 (-50°C to 70°C)

Intrinsic SafetyI3 Certification No. GYJ071171X

Ex ia IIC T4/T5T4: (-60°C to 70°C)T5: (-60°C to 40°C)Input Parameters:

Ui = 30 VdcIi = 185 mA Pi = 1.0 WCi = 0 FLi = 0.97 mH

Type N CertificationN3 Certification No. GYJ071193X

Ex nAnL IIC T5 (-40°C to70°C)

42 Vdc Max


Japanese Certifications (TIIS)

Flameproof CertificationE4 Transmitter - Ex d [ia] T6

Remote Sensor - Ex ia IIC T6

Certificate DescriptionTC17816 8800D with display, without MTA optionTC17817 8800D without display, without MTA option

TC17905 8800D with display, with MTA optionTC17906 8800D without display, with MTA option

24


Rosemount 8800D With FOUNDATION™ Fieldbus Protocol

North American Certifications

Factory Mutual (FM) Approvals E5 Explosion-proof for Class I, Division 1, Groups B, C, and D.

Dust Ignition-proof for Class II/III, Division 1, Groups E, F, and G.Temperature Code T6 (-50°C Ta 70°C)Factory SealedEnclosure Type 4X

I5 Intrinsically safe for use in Class I, II, III Division 1, Groups A, B, C, D, E, F, G; Class I, Zone 0, AEx ia IIC T4Non-incendive for Class I, Division 2, Groups A, B, C, and D. NIFW (Non-incendive Field Wiring) when installed per Rosemount Drawing 08800-0112T4 (-50°C to 60°C)Enclosure Type 4X.

IE FISCO/FNICO for Class I, Division 1, Groups A, B, C, and D. Class II/III, Division 1,Groups E, F, and G. T4 (-50°C to 60°C)when installed per Rosemount control drawing 08800-0116.

K5 E5 and I5 combination

Canadian Standards Association (CSA) ApprovalsSingle Seal

E6 Dust Ignition-proof for Class II and Class III, Division 1, Groups E, F, and G;Class I, Zone 1, Ex d[ia] IIC CSA 06.1674267T6 (-50°C to 70°C)Factory SealedSingle Seal.Enclosure Type 4X.

I6 Intrinsically safe for use in Class I, II, III Division 1, Groups A, B, C, D, E, F, G;Non-incendive for Class I, Division 2, Groups A, B, C and DT4 (-50°C to 60°C)Single Seal.Enclosure Type 4X.

IF FISCO/FNICO for Class I, Division 1, Groups A, B, C, and D;T4 (-50°C to 60°C)When installed per Rosemount drawing 08800-0112Enclosure Type 4X

K6 E6 and I6 combination.

Combination CertificationsKB E5, I5, E6, and I6 Combination

European Certifications

ATEX Intrinsic Safety CertificationI1 Certification No. Baseefa05ATEX0084X

ATEX Marking II 1 GEEx ia IIC T4 (-60°C Ta 60°C)

0575Input Parameters:Ui = 30 VdcIi = 300 mAPi = 1.3 WCi = 0 FLi = 20 H

SPECIAL CONDITIONS FOR SAFE USE (X)When fitted with 90V transient suppressors (T1 Option), the equipment is not capable of passing the 500V isolation test. This must be taken into account upon installation.

ATEX FISCO/FNICOIA Certification No. Baseefa05ATEX0084X

ATEX Marking II 1 G EEx ia IIC T4 (-60°C Ta 60°C)

0575Input Parameters:Ui = 17.5 VdcIi = 380 mAPi = 5.32 WCi = 0 FLi < 10 H


ATEX Type N CertificationN1 Certification No. Baseefa05ATEX0085X

ATEX Marking II 3 GEEx nAnL IIC T5 (-40°C Ta 70°C)Input Parameters:Ui = 32 Vdc MAXCi = 0 FLi = 20 H


25



ATEX Flameproof CertificationsE1 Certification No. KEMA 99ATEX3852X

ATEX Marking Remote Mount:Transmitter: II 2(1) G

EEx d [ia]IIC T6 (-50°C Ta 70°C)Meter Body: II 1 G

EEx ia IIC T6 (-50°C Ta 70°C)ATEX Marking Integral Mount: II 1/2 GEEx d [ia] IIC T6 (-50°C Ta 70°C)

0575V = 42 Vdc MaxUm = 250V


ATEX Dust CertificationND Certification No. Baseefa05ATEX0086

ATEX Marking II 1 D T90°C (-20°C Ta 70°C) Ui = 42 Vdc

0575

K1 E1, I1, N1 and ND Combination

International IECEx Certifications

Intrinsic SafetyI7 Certification No. IECEx BAS 05.0028X


Ui = 30 VdcIi = 300 mAPi = 1.3 WCi = 0 FLi = 20 H


FISCO/FNICOIG Certification No. IECEx BAS 05.0028X


Ui = 17.5 VdcIi = 380 mAPi = 5.32 WCi = 0 FLi 10H

Type N CertificationN7 Certification No. IECEx BAS 05.0029X

Ex nC IIC T5 (-40°C Ta 70°C)

Ui = 32 Vdc Max

Flameproof CertificationE7 Certification No. IECEx KEM 05.0017X

Marking Remote Mount:Transmitter: Ex d [ia] IIC T6 (-50°C Ta 70°C)Meter Body: Ex ia IIC T6 (-50°C Ta 70°C)

Marking Integral Mount: Ex d [ia] IIC T6(-50°C Ta 70°C)




26


Chinese Certifications (NEPSI)

Flameproof CertificationE3 Certification No. GYJ071327X

Ex d [ia] IIC T6 (-50°C to 70°C)

Intrinsic SafetyI3 Certification No. GYJ071171X

Ex ia IIC T6 (-60°C to 60°C)

Input Parameters:Ui = 30 VdcIi = 300 mAPi = 1.3 WCi = 0 FLi = 20H

FISCO/FNICOIH For FISCO:

Certification No. GYJ071171XEx ia IIC T4 (-60°C to 60°C)

Input Parameters:Ui = 17.5 VdcIi = 380 mAPi = 5.32 WCi = 0 FLi 10H

For FNICO:

Certification No. GYJ071193XEx nAnL IIC T5 (-40°C to 70°C)

17.5 Vdc Max

Type N CertificationN3 Certification No. GYJ071193X

Ex nAnL IIC T5 (-40°C to70°C)

32 Vdc Max


Japanese Certifications (TIIS)

Flameproof Certification

E4 TIIS FlameproofTransmitter - Ex d [ia] T6

Remote Sensor - Ex ia IIC T6

Certificate Description

TC17816 8800D with display, without MTA option

TC17817 8800D without display, without MTA option

TC17905 8800D with display, with MTA option

TC17906 8800D without display, with MTA option

27



Dimensional Drawings

Figure 2. Flanged-Style Flowmeter Dimensional Drawings (1/2-through 12-in./15 through 300 mm Line Sizes)

Terminal Cover

Display Option

Diameter3.06 (78)

Diameter B

3.20 (81)2.56 (65)

2.85 (72)

1.10(28)

1.00 (25.4)

C

A

2.00 (51)

NOTEDimensions are in inches (millimeters)

2.00 (51)

A

C

D

Diagram illustrated without MTA Option Diagram illustrated with MTA Option

28


Table 19. Flanged-Style Flowmeter (1/2-through 2-in./15 through 50 mm Line Sizes)

Nominal Size in. (mm)

Flange Rating

Face-to-face A in. (mm)

A-ANSI RTJ in. (mm)

Diameter B in. (mm)

C in. (mm)

Din. (mm)

Weight(1) lb (kg)

½ (15) Class 150Class 300Class 600Class 900

6.8 (173)7.2 (183)7.7 (196)8.3 (211)

–7.6 (193)7.6 (193)8.3 (211)

0.54 (13,7)0.54 (13,7)0.54 (13,7)0.54 (13,7)

7.6 (193)7.6 (193)7.6 (193)7.6 (193)

––––

9.1 (4,1)10.4 (4,7)10.8 (4,9)15.6 (7,1)

PN 16/40PN 100PN 160

6.1 (155)6.6 (168)6.6 (168)

–––

0.54 (13,7)0.54 (13,7)0.54 (13,7)

7.6 (193)7.6 (193)7.6 (193)

–––

10.4 (4,7)12.4 (5,6)12.4 (5,6)

JIS 10K/20KJIS 40K

6.3 (160)7.3 (185)

––

0.54 (13,7)0.54 (13,7)

7.6 (193)7.6 (193)

––

10.2 (4,6)13.7 (6,2)

1 (25) Class 150Class 300Class 600Class 900Class 1500

7.5 (191)8.0 (203)8.5 (216)9.4 (239)9.4 (239)

8.0 (203)8.5 (216)8.5 (216)9.4 (239)9.4 (239)

0.95 (24,1)0.95 (24,1)0.95 (24,1)0.95 (24,1)0.95 (24,1)

7.7 (196)7.7 (196)7.7 (196)7.7 (196)7.7 (196)

–––––

12.3 (5,6)15.0 (6,8)15.8 (7,2)24.4 (11,1)24.4 (11,1)

PN 16/40PN 100PN 160PN 250

6.2 (157)7.7 (195)7.7 (195)7.8 (198)

––––

0.95 (24,1)0.95 (24,1)0.95 (24,1)0.95 (24,1)

7.7 (196)7.7 (196)7.7 (196)7.7 (196)

––––

13.6 (6,2)19.6 (8,9)19.6 (8,9)

23.7 (10,7)JIS 10K/20K

JIS 40K6.5 (165)7.8 (198)

––

0.95 (24,1)0.95 (24,1)

7.7 (196)7.7 (196)

––

14.0 (6,3)17.7 (7,9)

1 ½ (40) Class 150Class 300Class 600Class 900Class 1500

8.2 (208)8.7 (221)9.3 (236)

10.3 (262)10.3 (262)

8.7 (221)9.2 (234)9.3 (236)

10.3 (262)10.3 (262)

1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)

8.1 (206)8.1 (206)8.1 (206)8.1 (206)8.1 (206)

–––––

17.6 (8,0)23.0 (10,5)25.5 (11,6)36.6 (16,6)36.6 (16,6)

PN 16/40PN 100PN 160PN 250

6.9 (175)8.2 (208)8.4 (213)9.6 (244)

––––

1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)

8.1 (206)8.1 (206)8.1 (206)8.1 (206)

––––

19,4 (8,8)28.0 (12,7)29.5 (13,4)39.2 (17,8)

JIS 10K/20KJIS 40K

7.3 (185)8.4 (213)

––

1.49 (37,8)1.49 (37,8)

8.1 (206)8.1 (206)

––

18.6 (8,4)25.5 (11,6)


9.2 (234)9.7 (246)

10.5 (267)12.7 (323)12.7 (323)

9.7 (246)10.4 (264)10.7 (271)12.9 (328)12.9 (328)

1.92 (48,8)1.92 (48,8)1.92 (48,8)1.92 (48,8)1.67 (42,4)

8.5 (216)8.5 (216)8.5 (216)8.5 (216)8.5 (216)

4.7 (119)4.7 (119)4.7 (119)4.7 (119)4.7 (119)

22.0 (10,1)26.1 (11,8)29.8 (13,5)59.5 (27,0)61.9 (28,1)

PN 16/40PN 64PN 100PN 160PN 250

8.0 (203)9.1 (231)9.6 (244)

10.2 (259)10.9 (277)

–––––

1.92 (48,8)1.92 (48,8)1.92 (48,8)1.92 (48,8)1.67 (42,4)

8.5 (216)8.5 (216)8.5 (216)8.5 (216)8.5 (216)

4.7 (119)4.7 (119)4.7 (119)4.7 (119)4.7 (119)

23.2 (10,5)30.8 (13,9)36.5 (16,6)38.8 (17,6)47.4 (21,5)

JIS 10KJIS 20KJIS 40K

7.7 (195)8.2 (208)9.8 (249)

–––

1.92 (48,8)1.92 (48,8)1.92 (48,8)

8.5 (216)8.5 (216)8.5 (216)

4.7 (119)4.7 (119)4.7 (119)

19.5 (8,8)20.4 (9,3)

28.5 (12,9)

(1) Add 0.2 lb (0,1 kg) for display option.

29



Table 20. Flanged-Style Flowmeter (3-through 6-in./80 through 150 mm Line Sizes) (Refer to previous drawing)

Nominal Size in. (mm) Flange Rating


A ANSI RTJ in. (mm)

Diameter B in. (mm) C in. (mm)

Din. (mm) Weight(1) lb (kg)


9.9 (251)10.6 (269)11.4 (290)12.9 (328)14.1 (358)

10.4 (264)11.2 (284)11.5 (292)13.0 (330)14.2 (361)

2.87 (72,9)2.87 (72,9)2.87 (72,9)2.87 (72,9)2.66 (67,6)

9.1 (231)9.1 (231)9.1 (231)9.1 (231)9.1 (231)

5.3 (135)5.3 (135)5.3 (135)5.3 (135)5.3 (135)

37.2 (16,9)46.5 (21,1)52.6 (23,8)76.1 (34,5)

108.9 (49,4)PN 16/40

PN 64PN 100PN 160PN 250

8.9 (226)10.0 (254)10.5 (267)11.1 (282)12.4 (315)

–––––

2.87 (72,9)2.87 (72,9)2.87 (72,9)2.87 (72,9)2.60 (66.0)

9.1 (231)9.1 (231)9.1 (231)9.1 (231)9.1 (231)

5.3 (135)5.3 (135)5.3 (135)5.3 (135)5.3 (135)

36.6 (16,6)45.3 (20,6)54.7 (24,8)59.6 (27,0)90.1 (40,9)


7.9 (200)9.3 (235)11.0 (280)

–––

2.87 (72,9)2.87 (72,9)2.87 (72,9)

9.1 (231)9.1 (231)9.1 (231)

5.3 (135)5.3 (135)5.3 (135)

28.0 (12,7)35.4 (16,1)50.3 (22,8)


10.3 (262)11.0 (279)12.8 (325)13.8 (351)14.5 (368)

10.8 (274)11.6 (295)12.9 (328)13.9 (353)14.6 (371)

3.79 (96,3)3.79 (96,3)3.79 (96,3)3.79 (96,3)3.40 (86,4)

9.6 (244)9.6 (244)9.6 (244)9.6 (244)9.6 (244)

5.9 (150)5.9 (150)5.9 (150)5.9 (150)5.9 (150)

51.3 (23,3)71.5 (32,4)97.5 (44,2)

120.8 (54,8)162.6 (73,8)

PN 16PN 40PN 64

PN 100PN 160PN 250

8.4 (213)9.4 (239)

10.4 (264)11.3 (287)12.1 (307)13.7 (348)

––––––

3.79 (96,3)3.79 (96,3)3.79 (96,3)3.79 (96,3)3.79 (96,3)3.40 (86,4)

9.6 (244)9.6 (244)9.6 (244)9.6 (244)9.6 (244)9.6 (244)

5.9 (150)5.9 (150)5.9 (150)5.9 (150)5.9 (150)5.9 (150)

40.4 (18,2)49.5 (22,4)62.5 (28,3)78.9 (35,8)86.2 (39,1)

143.4 (65,0)JIS 10KJIS 20KJIS 40K

8.7 (220)8.7 (220)11.8 (300)

–––

3.79 (96,3)3.79 (96,3)3.79 (96,3)

9.6 (244)9.6 (244)9.6 (244)

5.9 (150)5.9 (150)5.9 (150)

37.5 (17,0)45.4 (20,6)75.8 (34,4)


11.6 (295)12.3 (315)14.3 (363)16.1 (409)18.6 (472)

12.1 (307)13.0 (330)14.5 (368)16.2 (411)18.8 (478)

5.7 (144,8)5.7 (144,8)5.7 (144,8)

5.14 (130,6)5.14 (130,6)

10.8 (274)10.8 (274)10.8 (274)10.8 (274)10.8 (274)

7.4 (188)7.4 (188)7.4 (188)7.4 (188)7.4 (188)

81 (37)120 (55)187 (85)

277.9 (126,0)375.8 (170,4)

PN 16PN 40PN 64

PN 100PN 160PN 250

8.9 (226)10.5 (267)12.1 (307)13.6 (345)14.7 (373)17.2 (437)

––––––

5.7 (144,8)5.7 (144,8)5.7 (144,8)5.7 (144,8)

5.14 (130,6)5.14 (130,6)

10.8 (274)10.8 (274)10.8 (274)10.8 (274)10.8 (274)10.8 (274)

7.4 (188)7.4 (188)7.4 (188)7.4 (188)7.4 (188)7.4 (188)

66 (30)86 (39)

130 (59)160 (73)

202.2 (91.7)312 (141,6)


10.6 (270)10.6 (270)14.2 (360)

–––

5.7 (144,8)5.7 (144,8)5.7 (144,8)

10.8 (274)10.8 (274)10.8 (274)

7.4 (188)7.4 (188)7.4 (188)

70 (32)88 (40)

166 (75)


30


Table 21. Flanged-Style Flowmeter (8-through 12-in./200 through 300 mm Line Sizes) (Refer to previous drawing)


Flange Rating


A ANSI RTJ in. (mm)

Diameter B in. (mm) C in. (mm)

Din. (mm) Weight(1) lb (kg)


13.5 (343)14.3 (363)16.5 (419)18.8 (478)22.8 (579)

14.0 (356)14.9 (378)16.7 (424)18.9 (480)23.2 (589)

7.55 (191,8)7.55 (191,8)7.55 (191,8)6.62 (168,1)6.62 (168,1)

11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)

8.3 (211)8.3 (211)8.3 (211)8.3 (211)8.3 (211)

141.6 (64,2)198.7 (90,1)

298.6 (135,2)479.2 (217,4)652.4 (259,9)

PN 10PN 16PN 25PN 40PN 64PN 100PN 160PN250

10.4 (264)10.4 (264)11.8 (300)12.5 (318)14.2 (361)15.8 (401)16.6 (422)20.5 (521)

––––––––

7.55 (191,8)7.55 (191,8)7.55 (191,8)7.55 (191,8)7.55 (191,8)7.55 (191,8)6.62 (168,1)6.62 (168,1)

11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)

8.3 (211)8.3 (211)8.3 (211)8.3 (211)8.3 (211)8.3 (211)8.3 (211)8.3 (211)

110.5 (50,1)109.4 (49,6)137.7 (62,5)156.5 (71,0)217.1 (98,5)

282.7 (128,2)346.6 (157,2)570.5 (258,8)


12.2 (310)12.2 (310)16.5 (419)

–––

7.55 (191,8)7.55 (191,8)7.55 (191,8)

11.7 (297)11.7 (297)11.7 (297)

8.3 (211)8.3 (211)8.3 (211)

110.1 (49,9)134.5 (61,0)255.7 (116,0)

10 (250) Class 150Class 300Class 600

14.5 (368)15.8 (401)19.0 (483)

15.0 (381)16.4 (417)19.2 (488)

9.56 (242,8)9.56 (242,8)9.56 (242,8)

12.8 (325)12.8 (325)12.8 (325)

9.3 (236)9.3 (236)9.3 (236)

197.7 (89,7)286.2 (129,8)477.9 (216,9)

PN 10PN 16PN 25PN 40PN 64PN 100

11.9 (302)12.0 (307)13.5 (343)14.8 (376)16.4 (417)18.9 (480)

––––––

9.56 (242,8)9.56 (242,8)9.56 (242,8)9.56 (242,8)9.56 (242,8)9.56 (242,8)

12.8 (325)12.8 (325)12.8 (325)12.8 (325)12.8 (325)12.8 (325)

9.3 (236)9.3 (236)9.3 (236)9.3 (236)9.3 (236)9.3 (236)

157.1 (71,3)161.9 (73,5)198.6 (90,1)246.8 (111,9)308.2 (139,8)445.2 (201,9)


14.5 (368)14.5 (368)18.1 (460)

–––

9.56 (242,8)9.56 (242,8)9.56 (242,8)

12.8 (325)12.8 (325)12.8 (325)

9.3 (236)9.3 (236)9.3 (236)

174.5 (79,1)221.8 (100,6)378.5 (171,7)


16.8 (427)18.0 (457)20.5 (521)

17.3 (439)18.6 (472)20.6 (523)

11.38 (289,0)11.38 (289,0)11.38 (289,0)

13.7 (348)13.7 (348)13.7 (348)

10.1 (256)10.1 (256)10.1 (256)

297.5 (134,9)415.7 (188,6)595.4 (270,1)

PN 10PN 16PN 25PN 40PN 64PN 100

13.1 (333)13.9 (353)15.0 (381)16.8 (427)18.8 (478)21.2 (538)

––––––

11.38 (289,0)11.38 (289,0)11.38 (289,0)11.38 (289,0)11.38 (289,0)11.38 (289,0)

13.7 (348)13.7 (348)13.7 (348)13.7 (348)13.7 (348)13.7 (348)

10.1 (256)10.1 (256)10.1 (256)10.1 (256)10.1 (256)10.1 (256)

204.1 (92,6)224.6 (101,9)269.4 (122,2)347.9 (157,8)431.2 (195,6)644.1 (292,2)


15.7 (399)15.7 (399)19.6 (498)

–––

11.38 (289,0)11.38 (289,0)11.38 (289,0)

13.7 (348)13.7 (348)13.7 (348)

10.1 (256)10.1 (256)10.1 (256)

222.9 (101,1)284.2 (128,9)493.8 (224,0)


31



Figure 3. Rosemount 8800DR Reducer Flowmeter Dimensional Drawings (1-through 12-in./25 through 300 mm Line Sizes)

Diameter B

DisplayOption

1.00 (25)

3.20 (81) 2.85

(72)2.56 (65)

1.10(28)

Diameter3.06 (78)

Terminal Cover


2.00 (51)

A

C C

A

2.00 (51)

D

Diagram illustrated without MTA Option Diagram illustrated with MTA Option

32


TABLE 22. Reducer Flowmeter (1-through 3-in./25 through 80 mm Line Sizes)


Flange Rating


A-ANSI RTJ in. (mm)

Diameter B in. (mm)

C in. (mm) D in. (mm)

Weight(1) lb (kg)

1 (25) Class 150 7.5 (191) 8.0 (203) 0.54 (13,7) 7.6 (193) – 11.6 (5,2)Class 300 8.0 (203) 8.5 (216) 0.54 (13,7) 7.6 (193) – 14.2 (6,4)Class 600 8.5 (216) 8.5 (216) 0.54 (13,7) 7.6 (193) – 15.1 (6,9)Class 900 9.4 (239) 9.4 (239) 0.54 (13,7) 7.6 (193) – 20.7 (9.4)PN 16/40 6.2 (157) – 0.54 (13,7) 7.6 (193) – 12.6 (5,7)PN 100 7.7 (195) – 0.54 (13,7) 7.6 (193) – 18.4 (8,4)

1 ½ (40) Class 150 8.2 (208) 8.7 (221) 0.95 (24,1) 7.7 (196) – 15.8 (7,20)Class 300 8.7 (221) 9.2 (234) 0.95 (24,1) 7.7 (196) – 21.2 (9,6)Class 600 9.3 (236) 9.3 (236) 0.95 (24,1) 7.7 (196) – 23.8 (10,8)Class 900 10.3 (262) 10.3 (262) 0.95 (24,1) 7.7 (196) – 35.0 (15,9)PN 16/40 6.9 (175) – 0.95 (24,1) 7.7 (196) – 17.5 (7,9)PN 100 8.2 (208) – 0.95 (24,1) 7.7 (196) – 26.2 (11,9)PN 160 8.4 (213) – 0.95 (24,1) 7.7 (196) – 27.7 (12,6)

2 (50) Class 150 9.2 (236) 9.7 (249) 1.49 (37,8) 8.1 (206) 4.7 (119) 22.6 (10,3)Class 300 9.7 (249) 10.4 (264) 1.49 (37,8) 8.1 (206) 4.7 (119) 26.8 (12,1)Class 600 10.5 (267) 10.6 (269) 1.49 (37,8) 8.1 (206) 4.7 (119) 30.6 (13,9)Class 900 12.7 (323) 12.9 (328) 1.49 (37,8) 8.1 (206) 4.7 (119) 60.8 (27,6)PN 16/40 8.0 (203) – 1.49 (37,8) 8.1 (206) 4.7 (119) 23.5 (10,7)

PN 64 9.1 (231) – 1.49 (37,8) 8.1 (206) 4.7 (119) 31.3 (14,2)PN 100 9.6 (244) – 1.49 (37,8) 8.1 (206) 4.7 (119) 37.2 (16,9)PN 160 10.2 (259) – 1.49 (37,8) 8.1 (206) 4.7 (119) 39.6 (18,0)

3 (80) Class 150 9.9 (251) 10.4 (264) 1.92 (48,8) 8.5 (216) 5.3 (134) 33.2 (15,0)Class 300 10.6 (269) 11.2 (284) 1.92 (48,8) 8.5 (216) 5.3 (134) 42.7 (19,4)Class 600 11.4 (290) 11.5 (292) 1.92 (48,8) 8.5 (216) 5.3 (134) 49.5 (22,4)Class 900 12.9 (328) 13.0 (330) 1.92 (48,8) 8.5 (216) 5.3 (134) 73.3 (33,2)PN 16/40 8.9 (226) – 1.92 (48,8) 8.5 (216) 5.3 (134) 33.3 (15,1)

PN 64 10.0 (254) – 1.92 (48,8) 8.5 (216) 5.3 (134) 42.4 (19,3)PN 100 10.5 (267) – 1.92 (48,8) 8.5 (216) 5.3 (134) 52.2 (23,7)PN 160 11.1 (282) – 1.92 (48,8) 8.5 (216) 5.3 (134) 57.9 (26,3)


33



TABLE 23. Reducer Flowmeter (4-through 12-in./100 through 300mm Line Sizes) (Refer to previous drawing)


Flange Rating


A ANSI RTJ in. (mm)

Diameter B in. (mm) C in. (mm) D in. (mm) Weight(1) lb (kg)

4 (100) Class 150 10.3 (262) 10.8 (274) 2.87 (72,9) 9.1 (231) 5.9 (149) 46.3 (21,0)Class 300 11.0 (279) 11.6 (295) 2.87 (72,9) 9.1 (231) 5.9 (149) 67.0 (30,4)Class 600 12.8 (325) 12.9 (328) 2.87 (72,9) 9.1 (231) 5.9 (149) 94.3 (42,8)Class 900 13.8 (351) 13.9 (353) 2.87 (72,9) 9.1 (231) 5.9 (149) 118.0 (53,5)

PN 16 8.4 (213) – 2.87 (72,9) 9.1 (231) 5.9 (149) 36.4 (16,5)PN 40 9.4 (239) – 2.87 (72,9) 9.1 (231) 5.9 (149) 45.9 (20,8)PN 64 10.4 (264) – 2.87 (72,9) 9.1 (231) 5.9 (149) 59.7 (27,1)

PN 100 11.3 (287) – 2.87 (72,9) 9.1 (231) 5.9 (149) 76.7 (34,8)PN 160 12.1 (307) – 2.87 (72,9) 9.1 (231) – 84.7 (38,4)

6 (150) Class 150 11.6 (295) 12.1 (307) 3.79 (96,3) 9.6 (244) 7.4 (187) 70.3 (31,9)Class 300 12.3 (312) 13.0 (330) 3.79 (96,3) 9.6 (244) 7.4 (187) 113.1 (51,3)Class 600 14.3 (363) 14.4 (366) 3.79 (96,3) 9.6 (244) 7.4 (187) 185.1 (84,0)Class 900 16.1 (409) 16.2 (411) 3.79 (96,3) 9.6 (244) 7.4 (187) 246.3 (111,7)

PN 16 8.9 (226) – 3.79 (96,3) 9.6 (244) 7.4 (187) 59.2 (26,9)PN 40 10.5 (267) – 3.79 (96,3) 9.6 (244) 7.4 (187) 81.9 (37,2)PN 64 12.1 (307) – 3.79 (96,3) 9.6 (244) 7.4 (187) 125.4 (56,9)

PN 100 13.6 (345) – 3.79 (96,3) 9.6 (244) 7.4 (187) 162.3 (73,6)PN 160 14.7 (373) – 3.79 (96,3) 9.6 (244) 7.4 (187) 187.9 (85,2)

8 (200) Class 150 13.5 (343) 14.0 (356) 5.70 (144,8) 10.8 (274) 8.3 (210) 124 (56)Class 300 14.3 (363) 14.9 (378) 5.70 (144,8) 10.8 (274) 8.3 (210) 186 (84)Class 600 16.5 (419) 16.7 (424) 5.70 (144,8) 10.8 (274) 8.3 (210) 295 (134)

PN 10 10.4 (264) – 5.70 (144,8) 10.8 (274) 8.3 (210) 91 (41)PN 16 10.4 (264) – 5.70 (144,8) 10.8 (274) 8.3 (210) 91 (41)PN 25 11.8 (300) – 5.70 (144,8) 10.8 (274) 8.3 (210) 124 (56)PN 40 12.5 (318) – 5.70 (144,8) 10.8 (274) 8.3 (210) 145 (66)PN 64 14.2 (361) – 5.70 (144,8) 10.8 (274) 8.3 (210) 211 (96)

PN 100 15.8 (401) – 5.70 (144,8) 10.8 (274) 8.3 (210) 283 (128)10 (250) Class 150 14.5 (368) 15.0 (381) 7.55 (191,8) 11.7 (297) 9.3 (236) 182.4 (82,8)

Class 300 15.8 (401) 16.4 (417) 7.55 (191,8) 11.7 (297) 9.3 (236) 281.7 (127,8)Class 600 19.0 (483) 19.2 (488) 7.55 (191,8) 11.7 (297) 9.3 (236) 489.9 (222,2)

PN 10 11.9 (302) – 7.55 (191,8) 11.7 (297) 9.3 (236) 138.6 (62,9)PN 16 12.0 (305) – 7.55 (191,8) 11.7 (297) 9.3 (236) 148.6 (67,4)PN 25 13.5 (343) – 7.55 (191,8) 11.7 (297) 9.3 (236) 191.0 (86,6)PN 40 14.8 (376) – 7.55 (191,8) 11.7 (297) 9.3 (236) 245.8 (111,5)PN 64 16.4 (417) – 7.55 (191,8) 11.7 (297) 9.3 (236) 314.1 (142,5)

PN 100 18.9 (480) – 7.55 (191,8) 11.7 (297) 9.3 (236) 463.5 (210,2)12 (300) Class 150 16.8 (427) 17.3 (439) 9.56 (242,8) 12.8 (325) 10.1 (256) 282.0 (127,9)

Class 300 18.0 (457) 18.6 (472) 9.56 (242,8) 12.8 (325) 10.1 (256) 412.2 (187,0)Class 600 20.5 (521) 20.6 (523) 9.56 (242,8) 12.8 (325) 10.1 (256) 609.9 (276,6)

PN 10 13.1 (333) – 9.56 (242,8) 12.8 (325) 10.1 (256) 188.3 (85,4)PN 16 13.9 (353) – 9.56 (242,8) 12.8 (325) 10.1 (256) 211.8 (96,1)PN 25 15.0 (381) – 9.56 (242,8) 12.8 (325) 10.1 (256) 262.4 (119,1)PN 40 16.8 (427) – 9.56 (242,8) 12.8 (325) 10.1 (256) 349.9 (158,7)PN 64 18.8 (478) – 9.56 (242,8) 12.8 (325) 10.1 (256) 444.2 (201,5)

PN 100 21.2 (538) – 9.56 (242,8) 12.8 (325) 10.1 (256) 672.1 (304,8)


34


35

Figure 4. Wafer-Style Dimensional Drawings (1/2-through 8-in./15 through 200 mm Line Sizes)

2.00 (51)

E

A

Diameter D

NOTEDimensions are in inches (millimeters)Electronics housing may be rotated in 90 degree increments

2.00 (51)

Terminal Cover

Diameter B

DisplayOption

1.00 (25)

3.20 (81)

2.85 (72)

2.56 (65)

1.10 (28)

C

Diameter3.06 (78)

Table 24. Rosemount 8800D Wafer-Style Meter

Nominal Sizein. (mm)

Face-to-face Ain. (mm)

Diameter Bin. (mm)

Cin. (mm)

Diameter Din. (mm)

Ein. (mm)

Weightlb (kg)(1)

½ (15) 2.56 (65) 0.52 (13,2) 7.63 (194) 1.38 (35,1) 0.17 (4,3) 6.8 (3,1)1 (25) 2.56 (65) 0.95 (24,1) 7.74 (197) 1.98 (50,3) 0.23 (5,9) 7.4 (3,4)

1½ (40) 2.56 (65) 1.49 (37,8) 8.14 (206) 2.87 (72,9) 0.18 (4,5) 10.0 (6,2)2 (50) 2.56 (65) 1.92 (48,8) 8.85 (224,8) 3.86 (98) 0.12 (3) 10.6 (4,8)3 (80) 2.56 (65) 2.87 (72,9) 9.62 (244,4) 5.00 (127) 0.25 (6,4) 13.6 (6,2)

4 (100) 3.42 (87) 3.79 (96,3) 10.48 (266,2) 6.20 (157,5) 0.44 (11,2) 21.4 (9,7)6 (150) 5.00 (127) 5.70 (144,8) 10.29 (261) 8.50 (216) 0.30 (7,6) 36 (16,3)8 (200) 6.60 (168) 7.55 (192) 11.22 (285) 10.62 (270) 0.70 (17,8) 62 (28)




36

Figure 5. Vortex Dual-Sensor Style Flowmeter Dimensional Drawings (1/2-in (15 mm) through 4-in. (100 mm) line sizes)

Figure 6. Vortex Dual-Sensor Style Flowmeter Dimensional Drawings (6-in. (150 mm) through 12-in. (300 mm) line sizes)

3.20 (81)

2.56 (65)

1.10 (28)

3.06 (78)

2.85 (72)

NOTE Dimensions are in inches (millimeters)

Diameter B

1.00 (25)

Display Option

Terminal Cover 2.00 (51)

2.00 (51)

C

C

A

NOTE Dimensions are in inches (millimeters)

A

C

C

Diameter B


37

Table 25. Vortex Dual-Sensor Style Flowmeter (1/2-through 3-in./15 through 80 mm Line Sizes)


FlangeRating


A ANSI RTJin. (mm)

Diameter B in. (mm)

C in. (mm)

Weightlb (kg)(1)

½ (15) Class 150Class 300Class 600Class 900

11.9 (302)12.3 (312)12.8 (325)13.4 (340)

–12.7 (323)12.7 (323)13.4 (340)

0.54 (13,7)0.54 (13,7)0.54 (13,7)0.54 (13,7)

7.6 (193)7.6 (193)7.6 (193)7.6 (193)

16.2 (7,4)17.4 (7,9)17.9 (8,1)

22.7 (10,3)PN 16/40PN 100PN 160

11.2 (284)11.7 (297)11.7 (297)

–––

0.54 (13,7)0.54 (13,7)0.54 (13,7)

7.6 (193)7.6 (193)7.6 (193)

17.4 (7,9)19.4 (8,8)19.4 (8,8)

JIS 10K/20KJIS 40K

11.4 (290)12.4 (315)

––

0.54 (13,7)0.54 (13,7)

7.6 (193)7.6 (193)

17.3 (7,8)20.8 (9,4)

1 (25) Class 150Class 300Class 600Class 900

Class 1500

15.0 (381)15.6 (396)16.1 (409)16.9 (429)16.9 (429)

15.6 (396)16.1 (409)16.1 (409)16.9 (429)16.9 (429)

0.95 (24,1)0.95 (24,1)0.95 (24,1)0.95 (24,1)0.95 (24,1)

7.7 (196)7.7 (196)7.7 (196)7.7 (196)7.7 (196)

20.7 (9,4)23.3 (10,6)24.2 (11,0)32.8 (14,9)32.8 (14,9)

PN 16/40PN 100PN 160PN 250

13.8 (351)15.3 (389)15.3 (389)15.4 (391)

––––

0.95 (24,1)0.95 (24,1)0.95 (24,1)0.95 (24,1)

7.7 (196)7.7 (196)7.7 (196)7.7 (196)

21.9 (9,9)28.0 (12,7)28.0 (12,7)32.0 (14,5)

JIS 10K/20KJIS 40K

14.0 (356)15.4 (391)

––

0.95 (24,1)0.95 (24,1)

7.7 (196)7.7 (196)

22.3 (10,1)26.0 (11,8)

1 ½ (40) Class 150Class 300Class 600Class 900

Class 1500

11.3 (287)11.8 (300)12.4 (315)13.4 (340)13.4 (340)

11.8 (300)12.3 (312)12.4 (315)13.4 (340)13.4 (340)

1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)

8.1 (206)8.1 (206)8.1 (206)8.1 (206)8.1 (206)

27.0 (12,2)32.4 (14,7)34.8 (15,8)45.9 (20,8)45.9 (20,8)

PN 16/40PN 100PN 160PN 250

9.9 (251)11.3 (287)11.4 (290)12.7 (323)

––––

1.49 (37,8)1.49 (37,8)1.49 (37,8)1.49 (37,8)

8.1 (206)8.1 (206)8.1 (206)8.1 (206)

28.7 (13,0)37.4 (16,9)38.8 (17,6)48.5 (22,0)

JIS 10K/20KJIS 40K

10.3 (262)11.5 (292)

––

1.49 (37,8)1.49 (37,8)

8.1 (206)8.1 (206)

27.9 (12,7)34.9 (15,8)


Class 1500

13.0 (330)13.5 (343)14.3 (363)16.5 (419)15.6 (396)

13.5 (343)14.0 (356)14.3 (363)16.7 (424)15.7 (399)

1.92 (48,8)1.92 (48,8)1.92 (48,8)1.92 (48,8)1.67 (42.4)

8.5 (216)8.5 (216)8.5 (216)8.5 (216)8.5 (216)

31.9 (14,5)35.7 (16,2)39.4 (17,9)69.1 (31,4)72.4 (32,9)

PN 16/40PN 64

PN 100PN 160PN 250

11.8 (300)12.9 (328)13.4 (340)13.9 (353)13.8 (351)

–––––

1.92 (48,8)1.92 (48,8)1.92 (48,8)1.92 (48,8)1.92 (48,8)

8.5 (216)8.5 (216)8.5 (216)8.5 (216)8.5 (216)

32.8 (14,9)40.4 (18,3)46.2 (20,9)48.4 (21,9)57.1 (25,9)


11.5 (292)12.0 (305)13.6 (345)

–––

1.92 (48,8)1.92 (48,8)1.92 (48,8)

8.5 (216)8.5 (216)8.5 (216)

29.1 (13,2)30.0 (13,6)38.1 (17,3)


Class 1500

14.3 (363)15.0 (381)15.8 (401)17.3 (439)18.5 (470)

14.8 (376)15.7 (399)15.9 (404)17.4 (442)18.7 (475)

2.87 (72,9)2.87 (72,9)2.87 (72,9)2.87 (72,9)2.60 (66.0)

9.1 (231)9.1 (231)9.1 (231)9.1 (231)9.1 (232)

50.6 (23.0)59.9 (27.2)65.9 (29.9)88.4 (40.8)

123.8 (56.2)PN 16/40

PN 64PN 100PN 160PN 250

13.4 (340)14.5 (368)14.9 (378)15.6 (396)16.8 (427)

–––––

2.87 (72,9)2.87 (72,9)2.87 (72,9)2.87 (72,9)2.60 (66.0)

9.1 (231)9.1 (231)9.1 (231)9.1 (231)9.1 (231)

50.0 (22.7)58.7 (26.6)68.0 (30.9)73.4 (33.3)103 (46.9)


12.3 (312)13.7 (348)15.5 (394)

–––

2.87 (72,9)2.87 (72,9)2.87 (72,9)

9.1 (231)9.1 (231)9.1 (231)

41.4 (18.8)48.8 (22.1)63.7 (28.9)



Table 26. Vortex Dual-Sensor Style Flowmeter (4- through 12-in./100 through 300 mm Line Sizes)

FlangeRating


A ANSI RTJin. (mm)

Diameter B in. (mm)

C in. (mm)

Weightlb (kg)(1)


Class 1500

15.2 (386)16.0 (406)17.7 (450)18.7 (475)20.0 (509)

15.7 (399)16.6 (422)17.9 (455)18.9 (480)20.2 (512)

3.79 (96,3)3.79 (96,3)3.79 (96,3)3.79 (96,3)3.40 (86.4)

9.6 (244)9.6 (244)9.6 (244)9.6 (244)9.6 (244)

69.7 (31,6)88.9 (40,8)116 (52,5)139 (63,1)184 (83,3)

PN 16PN 40PN 64

PN 100PN 160PN 250

13.3 (338)14.4 (366)15.4 (391)16.3 (414)17.1 (434)19.2 (488)

––––––

3.79 (96,3)3.79 (96,3)3.79 (96,3)3.79 (96,3)3.79 (96,3)3.40 (86.4)

9.6 (244)9.6 (244)9.6 (244)9.6 (244)9.6 (244)9.6 (244)

58.7 (26,6)67.8 (30,8)80.8 (36,7)97.2 (44,1)104 (47,4)162 (73,4)


13.6 (345)13.6 (345)16.8 (427)

–––

3.79 (96,3)3.79 (96,3)3.79 (96,3)

9.6 (244)9.6 (244)9.6 (244)

55.8 (25,3)63.8 (28,9)94.2 (42,7)


Class 1500

11.6 (295)12.3 (312)14.3 (363)16.1 (409)18.6 (472)

12.1 (307)13.0 (330)14.4 (366)16.2 (411)18.8 (478)

5.7 (144,8)5.7 (144,8)5.7 (144,8)

5.14 (130.6)5.14 (130.6)

10.8 (274)10.8 (274)10.8 (274)10.8 (274)10.8 (274)

85 (39)124 (57)191 (87)

282 (128)380 (173)

PN 16PN 40PN 64

PN 100PN 160PN 250

8.9 (226)10.5 (267)12.1 (307)13.6 (345)14.7 (373)17.2 (437)

––––––

5.7 (144,8)5.7 (144,8)5.7 (144,8)5.7 (144,8)

5.14 (130.6)5.14 (130.6)

10.8 (274)10.8 (274)10.8 (274)10.8 (274)10.8 (274)10.8 (274)

70 (32)90 (41)

134 (61)164 (75)207 (94)

316 (144)JIS 10KJIS 20KJIS 40K

10.6 (269)10.6 (269)14.2 (361)

–––

5.7 (144,8)5.7 (144,8)5.7 (144,8)

10.8 (274)10.8 (274)10.8 (274)

74 (34)92 (142)170 (77)


Class 1500

13.5 (343)14.3 (363)16.5 (419)18.8 (478)22.8 (579)

14.0 (356)14.9 (378)16.7 (424)18.9 (480)23.2 (589)

7.55 (191,8)7.55 (191,8)7.55 (191,8)6.62 (168,1)6.62 (168,1)

11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)

146 (66)203 (92)

303 (138)484 (220)657 (299)

PN 10PN 16PN 25PN 40PN 64

PN 100PN 160PN 250

10.4 (264)10.4 (264)11.8 (300)12.5 (318)14.2 (361)15.8 (401)16.6 (422)20.5 (521)

––––––––

7.55 (191,8)7.55 (191,8)7.55 (191,8)7.55 (191,8)7.55 (191,8)7.55 (191,8)6.62 (168,1)6.62 (168,1)

11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)11.7 (297)

115 (52)114 (52)142 (65)161 (73)

221 (101)287 (130)351 (160)575 (261)


12.2 (310)12.2 (310)16.5 (419)

–––

7.55 (191,8)7.55 (191,8)7.55 (191,8)

11.7 (297)11.7 (297)11.7 (297)

114 (52)139 (63)260 (118)

38



14.5 (368)15.8 (401)19.0 (483)

15.0 (381)16.4 (417)19.2 (488)

9.56 (243)9.56 (243)9.56 (243)

12.8 (325)12.8 (325)12.8 (325)

202 (91,6)290 (132)482 (219)


PN 100

11.9 (302)12.0 (305)13.5 (343)14.8 (376)16.4 (417)18.9 (480)

––––––

9.56 (243)9.56 (243)9.56 (243)9.56 (243)9.56 (243)9.56 (243)

12.8 (325)12.8 (325)12.8 (325)12.8 (325)12.8 (325)12.8 (325)

161 (73,2)166 (75,4)203 (92,0)251 (11,4)312 (142)450 (204)


14.5 (368)14.5 (368)18.1 (460)

–––

9.56 (243)9.56 (243)9.56 (243)

12.8 (325)12.8 (325)12.8 (325)

179 (81,4)226 (103)383 (174)


16.8 (427)18.0 (457)20.5 (521)

17.3 (439)18.6 (472)20.6 (523)

11.38 (289)11.38 (289)11.38 (289)

13.7 (348)13.7 (348)13.7 (348)

302 (137)420 (191)600 (272)


PN 100

13.1 (333)13.9 (353)15.0 (381)16.8 (427)18.8 (478)21.2 (538)

––––––

11.38 (289)11.38 (289)11.38 (289)11.38 (289)11.38 (289)11.38 (289)

13.7 (348)13.7 (348)13.7 (348)13.7 (348)13.7 (348)13.7 (348)

208 (94,5)229 (104)274 (124)352 (160)435 (198)648 (294)


15.7 (399)15.7 (399)19.6 (498)

–––

11.38 (289)11.38 (289)11.38 (289)

13.7 (348)13.7 (348)13.7 (348)

227 (103)288 (131)498 (226)

(1) Add 0.4 Lb (0,2 kg) for display option.

Table 26. Vortex Dual-Sensor Style Flowmeter (4- through 12-in./100 through 300 mm Line Sizes)

39



40

Figure 7. Vortex weld-end style flowmeter dimensional drawings (1/2 - 4-in. (15 - 100 mm) line sizes)

DisplayOption

3.06(78)

3.20(81)

2.56(65)

2.85(72)

Terminal Cover

C

1.00 (25.4)

Electrical Connection

2.00 (51)

2.00 (51)

B

A

D

1.10(28)

Table 27. Vortex weld-end style flowmeter (1/2 - 4-in. (15 - 100 mm) line sizes)

Nominal Size in. (mm) A in. (mm) B in. (mm) C ± 0.20 in. (5.1 mm)Diameter D ± 0.031 in.

(0.79 mm)

0.5 16.0 (406) 8.0 (203) 7.63 (194) .840 (21.34)1 16.0 (406) 8.0 (203) 7.74 (197) 1.315 (33.40)

1.5 16.0 (406) 8.0 (203) 8.14 (207) 1.900 (48.26)2 16.0 (406) 8.0 (203) 8.49 (216) 2.375 (60.33)3 16.0 (406) 8.0 (203) 9.05 (230) 3.500 (88.90)4 16.0 (406) 8.0 (203) 9.60 (244) 4.500 (114.30)


41

Figure 8. Dimensional Drawings for Remote Mount Transmitters

3.20 (81)

2.56 (65)

1.10 (28)

2.85 (72)

1.00 (25,4)

4.35 (110)

3.06 (78)

Display Option

Terminal Cover

NOTEConsult factory for SST installationDimensions are in inches (millimeters)

5.77 (147)

1/2-14 NPT (For RemoteCable Conduit)

2.00 (51)

3.12 (80)

6.77(172)

2.44 (62)


Figure 9. Dimensional Drawings for Remote Mount Wafer-Style Flowmeters (1/2-through 8-in./15 through 200 mm Line Sizes)
E


1/2-14 NPT (For Remote Cable Conduit)

Table 28. Rosemount 8800D Wafer-Style Meter

Nominal Size in. (mm) E Wafer Style in. (mm)

½ (15) 6.4 (163)1 (25) 6.5 (165)

1½ (40) 6.9 (175)2 (50) 7.6 (193)3 (80) 8.3 (211)

4 (100) 9.2 (234)6 (150) 9.5 (241)8 (200) 10.4 (264)

42


43

Figure 10. Dimensional Drawings for Flanged-and Dual Sensor Flanged-Style Remote Mount Flowmeters (1/2-through 12-in./15 through 300 mm Line Sizes)


Flanged Flowmeter


E


Dual-Sensor Style Flowmeter

E

E

Table 29. Remote Mount, Flanged-and Dual Sensor Flowmeter Dimensions

Nominal Size in. (mm) E Flange Style in. (mm)

½ (15) 6.4 (162)1 (25) 6.5 (165)

1½ (40) 6.8 (173)2 (50) 7.2 (183)3 (80) 7.8 (198)

4 (100) 8.3 (211)6 (150) 9.5 (241)8 (200) 10.4 (264)

10 (250) 11.4 (290)12 (300) 12.3 (313)



Ordering Information Table 30. Rosemount 8800D Vortex Flowmeter★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.__The Expanded offering is subject to additional delivery lead time.

Model Product Description

8800D Vortex Flowmeter

Meter Style

Standard Standard

F Flanged style ★

W Wafer style ★

R Reducer Style (Flanged style only) ★

Expanded

D Dual-sensor style (Flanged style only)

Line Size

Standard Standard

005 1/2-in. (15 mm) (Not available for Rosemount 8800DR) ★

010 1-in. (25 mm) ★

015 11/2-in. (40 mm) ★

020 2-in. (50 mm) ★

030 3-in. (80 mm) ★

040 4-in. (100 mm) ★

Expanded

060 6-in. (150 mm)

080 8-in. (200 mm)

100 10-in. (250mm)

120 12-in. (300mm)

Wetted Materials

Standard Standard

S 316 wrought stainless and CF-3M cast stainlessNote: Material of construction is 316/316L

★

Expanded

H UNS N06022 wrought Nickel Alloy; CW2M cast Nickel AlloyNote: See Table 31 on page 49

Other wetted materials are available. Consult factory for details.

Flange or Alignment Ring Size

Standard Standard

A1 ASME B16.5 (ANSI) RF Class 150 ★

A3 ASME B16.5 (ANSI) RF Class 300 ★

D1 DIN PN 16 (PN 10/16 for wafer-style) 2526-Type D ★

D3 DIN PN 40 (PN 25/40 for wafer-style) 2526-Type D ★

Expanded

A6 ASME B16.5 (ANSI) RF Class 600

A7(1) ASME B16.5 (ANSI) RF Class 900

A8(2) ASME B16.5 (ANSI) RF Class 1500

B1 ASME B16.5 (ANSI) RTJ Class 150 for flange-style only



B7(1) ASME B16.5 (ANSI) RTJ Class 900 for flange-style only

B8(2) ASME B16.5 (ANSI) RTJ Class 1500 for flange-style only

C1 ASME B16.5 (ANSI) RF Class 150, smooth finish



C7(1) ASME B16.5 (ANSI) RF Class 900, smooth finish


44


D0 DIN PN 10 2526-Type D




D7(1) DIN PN 160 2526-Type D


G0 DIN PN 10 2512-Type N for flange-style only






G7(1) DIN PN 160 2512-Type N for flange-style only


H0 DIN PN 10 2526-Type E

H1 DIN PN 16 (PN 10/16 for wafer-style) 2526-Type E


H3 DIN PN 40 (PN 25/40 for wafer-style) 2526-Type E



H7(1) DIN PN 160 2526-Type E


J1 JIS 10K

J2 JIS 20K

J4 JIS 40K

W1(3) Weld End, Schedule 10S




Sensor Process Temperature Range

Standard Standard

N Standard: -40 to 450°F (-40 to 232°C) ★

E Extended: -330 to 800°F (-200 to 427°C) ★

Conduit Entry

Standard Standard

1 1/2 -14 NPT – Aluminum Housing ★

2 M20 � 1.5 – Aluminum Housing ★

4 G1/2 (One Conduit Entry) – Aluminum Housing ★

5 G1/2 (Two Conduit Entries) – Aluminum Housing ★

Expanded

6(4) 1/2 - 14 NPT - SST Housing

7(4) M20 x 1.5 - SST Housing

Outputs

Standard Standard

D 4-20 mA digital electronics (HART protocol) ★

P 4-20 mA digital electronics (HART protocol) with scaled pulse ★

F(5) FOUNDATION fieldbus digital signal ★

Calibration

Standard Standard

1 Flow calibration ★

Table 30. Rosemount 8800D Vortex Flowmeter★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.__The Expanded offering is subject to additional delivery lead time.

45



Options

MultiVariable Options

Expanded

MTA(6) MultiVariable output with Integral Temperature Sensor

Hazardous Locations Certifications

Standard Standard

E5 FM Explosion-proof, Dust Ignition-proof ★

I5 FM Intrinsically Safe, Non-incendive ★

IE FM FISCO Intrinsically Safe(7) ★

K5 FM Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Non-incendive ★

E6 CSA Explosion-proof, Dust Ignition-proof ★

I6 CSA Intrinsically Safe, Non-incendive ★

IF CSA FISCO Intrinsically Safe(7) ★

K6 CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Non-incendive ★

KB FM and CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Non-incendive ★

E1 ATEX Flameproof ★

I1 ATEX Intrinsic Safety ★

N1 ATEX Type n ★

ND ATEX Dust ★

IA ATEX FISCO Intrinsic Safety(7) ★

K1 ATEX Flameproof, Intrinsic Safety, Type n, Dust ★

E7 IECEx Flameproof ★

I7 IECEx Intrinsic Safety ★

N7 IECEx Type n ★

IG IECEx FISCO Intrinsic Safety(7) ★

K7 IECEx Flameproof, Intrinsic Safety, Type n ★

E3 China Flameproof ★

I3 China Intrinsic Safety ★

N3 China Type n ★

IH China FISCO/FNICO Intrinsic Safety(7) ★

K3 China Flameproof, Intrinsic Safety, Type n ★

E4(8) TIIS Flameproof ★

E2 INMETRO Flameproof ★

I2 INMETRO Intrinsic Safety ★

IB INMETRO FISCO Intrinsic Safety ★

Plantweb Control Functionality

Standard Standard

A01 Basic Control: One Proportional/Integral/Derivative (PID) Function Block ★

Conduit Electrical Connector

Expanded

GE(9) M12, 4-pin, Male Connector (eurofast®)

GM(9) A size Mini, 4-pin, Male Connector (minifast®)

GN ATEX Flameproof A size, Mini 4-pin male connector (minifast)

Other Options

Standard Standard

C4(10) NAMUR alarm and saturation values, high alarm ★

CN(10) NAMUR alarm and saturation values, low alarm ★

V5 (11) External ground screw assembly ★

T1 Transient protection terminal block ★

P2 Cleaning for special services ★


46


M5 LCD indicator ★

R10 Remote electronics with 10 ft (3,0 m) cable ★



R50 Remote electronics with 50 ft (15.,2 m) cable ★

Expanded

RXX(12) Remote electronics with customer-specified cable length (up to 75 ft (23 m) maximum)

CPA(13) CriticalProcess Online Sensor

Certification Options

Standard Standard

Q4 Calibration data sheet per ISO 10474 3.1B and EN 10204 3.1 ★

Q8 Material traceability certification per ISO 10474 3.1B and EN 10204 3.1 ★

QP Calibration certification and tamper evident seal ★

Q25 NACE MR0103 Certificate of Compliance ★

Q66 Certificate for Procedure Qualification Records ★

Q67 Certificate for Welder Performance Qualification Records ★

Q68 Certification for Welding Procedure Specifications ★

Q69(14) Inspection certificate weld examination (wafer) per ISO 10474 3.1B and EN 10204 3.1 ★

Q70 Inspection certificate weld examination (flanged) per ISO 10474 3.1B and EN 10204 3.1 ★

Q71 Inspection certification weld examination (flanged) per ISO 10474 3.1B (includes x-rays) and EN 10204 3.1

★

Q79 Certification for Combo PQR/WPQ/WPS ★

Expanded

QKH KHK Documentation Package

Quick Installation Guide (QIG) Language Options (Default is English)

Standard Standard

YA Danish QIG ★

YB Hungarian QIG ★

YC Czech QIG ★

YD Dutch QIG ★

YF French QIG ★

YG German QIG ★

YH Finnish QIG ★

YI Italian QIG ★

YJ Japanese QIG ★

YM Chinese (Mandarin) QIG ★

YN Norwegian QIG ★

YL Polish QIG ★

YP Portuguese QIG ★

YR Russian QIG ★

YS Spanish QIG ★

YW Swedish QIG ★

Typical Model Number: 8800D F 020 S A1 N 1 D 1 M5

(1) Available on flanged and dual style meters from 1/2” - 8” (15-200 mm) and Reducer style meters from 1” - 6” (25-150 mm).

(2) Only available for stainless steel flange and dual style meters from 1” - 8” (25-200 mm). Consult factory for other materials.

(3) W1, W4, W8, and W9 are only available with Meter Style F from 1/2-in. (15 mm) to 4-in. (100 mm) in SST.

(4) No TIIS approval

(5) Includes five Analog Input (AI) function blocks, 1 PID function block, 1 Integrator (INT) function block, 1 Arithmetic (ARITH) function block and Backup Link Active Scheduler.

(6) Available in Stainless Steel meter body only. Available with Rosemount 8800DF from 1 1/2-in (40 mm) through 12-in. (300 mm). Available with 8800DR from 2-in (50 mm) through 12-in (300 mm). Not available with 8800DW or 8800DD. Not available with flange codes A7, A8, B7, B8, C7, C8, D7, D8, G7, G8, H7, H8.


47



(7) Fieldbus Intrinsic Safe Concept available with output code F (FOUNDATION fieldbus digital signal).

(8) TIIS Flameproof Approval requires G1/2 conduit entry.

(9) Not available with certain hazardous location certifications. Contact a Rosemount representative for details.

(10) NAMUR compliant operation and the alarm latch options are pre-set at the factory and can be changed to standard operation in the field.

(11) V5 only available with no approval, it is standard with the other approvals.

(12) XX is a customer specified length in feet.

(13) The CPA option is not available on wafer, 1/2-in. flange, or 1-in. reducer units. In addition it is not available on 1" flanged and 1.5" reducer JIS 10K, DIN PN40, or DIN PN16.

(14) Q69 available for all Nickel Alloy wafers and stainless steel wafers in line sizes 1/2-in. (15 mm), 6-in. (150 mm), and 8-in. (200 mm).

48


Table 31. Method of Construction for the 8800DF in Nickel Alloy.

Line Size A1 A3 A6 A7 D1 D3 D4 D6 D7

½ (15) C C C W W W NA W W1 (25) C C C W W W NA W W

1½ (40) C C C W W W NA W W2 (50) C C C W C C W W W3 (80) C C C W C C W W W

4 (100) C C C W C C W W W6 (150) C C C CF W W W W CF8 (200) C C C CF W W W W CF

10 (250) W W W NA W W W W NA12 (300) W W W NA W W W W NA

C = Nickel Alloy collar and 316 SST lap flange. If weld neck flange is required, V0022 can be ordered.W = Nickel Alloy weld neck flange.CF = Consult FactoryNA = Not AvailableAll 8800DR Reducer Vortex Meters with Nickel Alloy materials of construction use weld neck flanges.Flange codes other than those listed in Table 29 all use weld neck flanges.

49

Emerson Process Management

Rosemount Inc.8200 Market BoulevardChanhassen, MN 55317 USAT 1-800-999-9307T (International) (952) 906-8888F (952) 949-7001

www.rosemount.com

Emerson Process Management FlowNeonstraat 1 6718 WX EdeThe Netherlands T +31 (0)318 495555F +31(0) 318 495556

Emerson Process Management Asia Pacific Private Limited1 Pandan CrescentSingapore 128461T (65) 777 8211F (65) 777 [email protected]

The Emerson logo is a trade mark and service mark of Emerson Electric Co.Rosemount and the Rosemount logotype are registered trademarks of Rosemount Inc.PlantWeb is a mark of one of the Emerson Process Management companies.All other marks are the property of their respective owners.

Approved by the Committee of Russian Federation for Standardization, Metrology and Certification (the Gosstandart of Russia) and registered in the Russian State Register of measuring instruments.Reducer Vortex is a trademark of Rosemount Inc.MultiVariable (MV) is a trademark of Rosemount Inc.Annubar is a registered trademark of Dieterich Standard Inc.Mass ProBar and ProBar are trademarks of Dieterich Standard Inc.HART is a registered trademark of the HART Communication Foundation.FOUNDATION is a trademark of the Fieldbus Foundation.



00813-0100-4004 Rev GA, 4/10

Rosemount 8800D Series Vortex Flowmeter€¦ · Rosemount 8800D Series Vortex Flowmeter. ... Rosemount 8800D 8800D MULTIVARIABLE VORTEX REDUCES INSTALLATION COSTS, ... manufacturer

Text of Rosemount 8800D Series Vortex Flowmeter€¦ · Rosemount 8800D Series Vortex Flowmeter. ......

Product Data Sheet: Rosemount 8800D Series Vortex Flowmeter...See Product Data Sheet 00813-0100-4005 for more information on the Rosemount Flow Computer. 5 November 2014 Rosemount

Rosemount 8800D Series Vortex Flowmeter...1 About this guide This guide provides basic guidelines for the Rosemount 8800D Series Vortex Flowmeter. It does not provide instructions

Rosemount™ 8800D Series Vortex - Emerson Electric...The fieldbus retains the desirable features of the 4–20 mA analog system, including a standardized physical interface to the

Rosemount 8800D Vortex Flowmeter - InstrumartB1 (7) ASME B16.5 RTJ Class 150 for flange-style only B3 ASME B16.5 RTJ Class 300 for flange-style only B6 ASME B16.5 RTJ Class 600 for

Rosemount 8800D Series Vortex Flowmeter · Reference Manual 00809-0100-4004, Rev DE Configuration May 2019 Configuration 2.1.4 Process Variable Units Allows for the viewing and configuration

Rosemount 8800D Series Vortex Flowmeter · The Rosemount 8800D CriticalProcess Vortex increases process availability and enhances overall safety Eliminate bypass piping for critical

Rosemount 8800D Series Vortex Flowmeter · 2019-08-01 · 2 Rosemount 8800D September 2015 The Rosemount 8800D delivers reliability and maximum process availability Rosemount Reliability

Rosemount® 8800D Series Vortex Flowmeter

Rosemount 8800D Series Vortex Flowmeter - 2.imimg.com2.imimg.com/data2/GD/GJ/MY-401892/rosemount-8800d-series-vortex-flowmeter.pdfProduct Data Sheet 00813-0100-4004, Rev HA April 2010

Rosemount 8800D Series Vortex Flowmeter - · PDF file6 Rosemount 8800D October 2017 Detect process fluid changes with SMART Fluid Diagnostics Oil and gas separators Remotely detect

October 2017 Rosemount 8800D Series Vortex Flowmeter ...€¦ · Rosemount™ 8800D Series Vortex Flowmeter Safety Manual for Safety Instrumented Systems ... • Identification of

Rosemount 8800, Rosemount 8800 Vortex Adaptive Digital ......traditional vortex designs have limitations such as ... environment may be quite different than the conditions under which

Quick Start Guide: Rosemount 8800D Series Vortex Flowmeter€¦ · Quick Start Guide 00825-0100-4004, Rev FC September 2017 Rosemount™ 8800D Series Vortex Flowmeter. April 2016

Rosemount 8800 Series of Instrumentation - · PDF fileRosemount 8800 Series of Instrumentation Vortex Flowmeters ... Traditional Vortex Limitations When vortex technology was introduced,

Rosemount 8800D Series Vortex Flowmeter - Instrumart · 2010-01-06 · Quick Installation Guide 00825-0100-4004, Rev CA Rosemount 8800D January 2008 4 High Temperature Mounting The

Rosemount 8800C Series Vortex Flowmeter - catalog 2006 -2007

Rosemount 8800D Series Vortex Flowmeter - emerson.com · 2 Rosemount 8800D October 2017 The Rosemount 8800D delivers reliability, safety, and maximum process availability Rosemount

Rosemount 8800D Series Vortex Flowmeter · 2019-01-16 · Reference Manual 00809-0100-4004, Rev DC Title Page May 2016 Title Page i Rosemount™ 8800D Series Vortex Flowmeter Read

Rosemount 8800D Series Vortex FlowmeterMultivariable vortex design Incorporates temperature sensor into the vortex meter using the shedder bar as a thermowell, which keeps the vortex

Rosemount 8800D Series Vortex Flowmeter · 00809-0100-4004, Rev CA Title Page June 2012 i Rosemount 8800D Series Vortex Flowmeter Read this manual before working with the product

Rosemount 8800D Series Vortex Flowmeter - november 2006

Rosemount 8800D Series Vortex Flowmeter - ELMOS · The Rosemount 8800D Flowmeter can be easily configured using the DeltaV system. User-configurable parameters include: tag, scaling

Rosemount 8800D Series Vortex Flowmeter - March 2006

Product Data Sheet October 2016 Rosemount 8600 Series ...Product Data Sheet October 2016 00813-0100-4860, Rev BC Rosemount™ 8600 Series Utility™ Vortex Flowmeter The Rosemount

Product Data Sheet: Rosemount 8800D Series Vortex Flowmeter

Rosemount 8800D Series Vortex Flowmeter - emerson.com · Product Data Sheet October 2018 00813-0100-4004, Rev KF HART® and FOUNDATION™ Fieldbus Protocols All welded, non-clog design

Rosemount 8800D Vortex Flowmeter - Emerson Electric · 2019-09-04 · Product Data Sheet 00813-0100-4004, Rev KG August 2019 Rosemount™ 8800D Vortex Flowmeter Industry Leading Vortex

Rosemount 8800D Series Vortex Flowmeter 8800D V… · Rosemount 8800D ROSEMOUNT 8800D VORTEX FLOWMETER WITH FOUNDATION FIELDBUS The software for the 8800D Flowmeter with FOUNDATION

Product Data Sheet: Rosemount 8800D Series Vortex Flowmeter · 2 Rosemount 8800D November 2014 The Rosemount 8800D delivers reliability and maximum process availability Rosemount

FMEDA Report: 8800D Vortex Flowmeter, Revision R2

Documents

Rosemount 8800D Series Vortex Flowmeter€¦ · Rosemount 8800D Series Vortex Flowmeter. ... Rosemount 8800D 8800D MULTIVARIABLE VORTEX REDUCES INSTALLATION COSTS, ... manufacturer

Text of Rosemount 8800D Series Vortex Flowmeter€¦ · Rosemount 8800D Series Vortex Flowmeter. ......