RIGS FOR WELL DEVELOPMENT REPAIRimzgroup.co.uk/wp-content/uploads/2016/05/IMZ-Oil-Gas...RIGS FOR WELL DEVELOPMENT & REPAIR MOBILE DRILLING RIGS A 60/80 Rig A60/80 is designed to repair

RIGS FOR WELL DEVELOPMENT&

REPAIR

RIGS FOR WELL DEVELOPMENT & REPAIR MOBILE DRILLING RIGS

A 60/80

Rig A60/80 is designed to repair and develop oil and gas wells,drill by means of rotary table and downhole engines.Rig units are mounted at all-wheel drive chassis KrAZ- 63221.0000044. Conditional well depth for repair and development is meter (tubing strings of 14 kg/m). Conditional well drilling depth is 2000 meter (at drilling with drilling string of 24 kg/m).

Design Features:• Single- or double-drum hoist with disk pneumatic clutches allowing immediate switching over from one to another speed range and not needing additional compressor;• Drawworks drum with Lebus grooves providing uniform cable winding;• Upper section extending by hydraulic hoist;• Hydraulic hoist for auxiliary operations;• Emergency electric drive;• Oil-filled chain transmission of drawworks drive;• Two-way hydraulic jacks (outriggers) with travel of 800 mm;• Carrying capacity limiter, traveling block lift height limiter;• Equipment set in accordance with preferred destination and operation specific.

TRAVELLING BLOCK PERFORMANCES

Safe hook load, kN (ton-force) 785 (80)

Device drive Engine of chassis YaMZ-238DE2 with power of 243 kW or YaMZ-7511 with power of 294 kW

Drawworks:• tackel block lifting speed, m/s• line capacity of bailing drum, m

Single- or double-drum, with disk pneumatic clutches and double-pulley band break0.15...1.92000 (015 mm) 2500 (013 mm)

Tower:• height of crown block above the ground level, mm• heigh of traveling block lift, mm

Telescopic, directional2260018500

Derrickman platform (pipe capacity) 280/3400 (drilling pipes of 089 mm, and length 12-13 m, pcs/m)

Traveling system: • stringing• hoist wireline diameter, mm

With hoist wireline cross-over unit3x425

Auxiliary hydraulic hoist :• safe load at hook, kN (ton-force)

29.5 (3)

Operational/Installation hydraulic system :• pump type and model• rated pressure, MPa (kg/cm’)• rated supply, m’/s (I/min)

Axial-piston 3102.112 2 pcs/NSh-50 19.6 (200)/15.7 (160)6.168x10- 3 (370)/0.833x10-3 (50)

Drill pipe breaker:• rod stroke, mm• max traction power, kN (ton-force)

100054 (5.5)

Manifold (riser and rotary hose):• passage diameter, mm• working fluid pressure, MPa (kg/cm’)

76 or 50 19.6 (200)

Emergency electric drive:• electric motor power, kW• tackle block lifting speed with max load at hook, m/s (m/min)

30

0.02 (1.2)

Base-plate under rear outriggers:• overall dimensions, m

Composite6x0.7x0.1 or 4.5x0.7x0.1

Emergency explosion-proof lightning, VOverall dimensions (in over-the-road position), mm Weight in over-the-road position, kg

220 (emergency 24)14400x3400x450032000 at chassis KrAZ-63221.0000044

v RIG FOR WELL DEVELOPMENT & REPAIR MOBILE DRILLING RIGS

PERFORMANCES OF COMPONENT EQUIPMENT

Wellhead operation platform:• overall dimensions, m• height (adjustable), m

flexiblefrom 2x2.5 to 3x41-3

Drum for hoist wireline cross-over: 500 (including 200 m for travel system stringing,and 300 m for additional wire)

Hydraulic rotary-and-tongs (with slip hanger): • passage diameter, mm• rotational speed, s’ (rpm)• max torque, kN-m (kg-force-m)

for operation with spanner wrench and stem of 80x801420.37 (21). 1.46 (86)4.4 (450)

Swivel: • static carrying capacity, kN (ton-force) • passage diameter, mm• rotational speed, s· 1 (rpm), no more than

785 (80)755 (300)

Rotary table (with cardan gear): • passage diameter, mm• rotational speed, s· 1 (rpm), no more than• max torque at table, kN-m (kg-force-m)

R-250 2500,83 (50) .. 5 (300)9.8 (1000)

R-4004000,67 (40) 4 (240)11.772 (1200)

Rotary table (with hydraulic drive): • passage diameter, mm• rotational speed, s· 1 (rpm), no more than• max torque, kN-m (kg-force-ml)

R-2502501,5 (90)12 (1200)

Wellhead platform (overall dimensions), mm: • distance from ground to rotary support beams, mm

4000x30001600 .. .3000

Pipe setback: • static load, kN (ton-force), no more than

785 (80)

Platform with racks: • overall dimensions in over-the-road position, mm• overall dimensions in operation position, mm

At triaxial trailer OZTP-84701A11400x2800x340015000x9800x2900

Cha

ssis

Destination

Composition, unit designation

Trav

ellin

g bl

ock

with

out b

ailin

g w

ithou

t bai

ling

drum

Trav

elin

g bl

ock

with

bai

ling

drum

.

Wel

lhea

d op

erat

ion

plat

form

Hyd

raul

ic ro

tary

-and

-tong

s

Dril

ling

rota

ry ta

ble

P-25

0 or

P-

400

with

car

dan

gear

.)

Dril

ling

rota

ry ta

ble

R-2

50

(with

hyd

raul

ic d

rive)

Swiv

el V

B 80

Dril

l gui

de 8

0x80

of

8 m

leng

th

Wel

lhea

d pl

atfo

rm

Pipe

stac

k

Pipe

rack

s

Emer

genc

y el

ectr

ic d

rive

Stem

112

x112

of

11m

leng

th

Cro

ss-o

ver d

rum

Man

ifold

with

pas

sage

dia

met

er

of Ø

50

mm

Man

ifold

with

pas

sage

dia

met

er

of Ø

76

mm

Der

rickm

an p

latfo

rm

KrA

Z-63

221.

0000

044

Well develop-ment, major

repair

A60/80.101

R250

Drilling oper-ation

A60/80.102

R400

Well develop-ment, major

repair, swabing

A60/80.111

R250

Drilling opera-tion,

swabbing

A60/80.112

R400

Equipment set in accordance with specifications TU3666-082-05749197-96

Equipment components by request

Equipment components by request

Equipment components set is stipulated under conclusion of contract

RIG FOR WELL DEVELOPMENT & REPAIR MOBILE DRILLING RIGS RIG FOR WELL DEVELOPMENT & REPAIR MOBILE DRILLING RIGS

A 60/80M

Travelling block permanences available on request.

UPA 60/80


RIG FOR WELL DEVELOPMENT & REPAIR MOBILE DRILLING RIGS

UPA-60A (60x80)

Hoisting rig for oil - and gas-well development and repair UPA - 60A is designed to develop, conduct current and major repair of oil - and gas-wells in conditions of regions with temperate and cold macro-climate.

It enables to conduct the following operations:• to lower and lift tubing, drill pipes, to circulate wells;• repair and accident elimination works, cement plug drilling in pipes 5-6”;• to install operational equipment at wellhead;• to conduct drilling works.

Distinction from basic model (rig A50M) is that it meets “Oil and Gas Industry Safety Regulations PB 08-624-03”, as well as usage of new technical solutions: • the rig is equipped with four hydraulic support jacks with mechanical locks, front and rear foundation girders; • tyre-pneumatic clutches are replaced with pneumatic friction clutches of diaphragm type with low air con-sumption which do not need an additional compressor;• carrying capacity limiter (limit torque clutch) is installed into transmission;• front tower support is excluded tower guys are remounted to the support behind the driver cab, that enables to improve driver’s field of view;• tower lifting control is made as remote control;• derrikman platform equipped with emergency evacuation device;• rig’s tower is equipped with audible and visual warning of upper section installation;• traveling block is replaced with multi-purpose hook-block;• the rig is equipped with spark-arrester and rectifier for battery recharging,• the transmission has an oil-bath for double-chain gear of hoist drive.

Hoisting rig for oil- and gas-well development and repair UPA-60A(60x80) is designed for all opera-tion which are the same as for UPA-60A and has additional feature of short term overloading up to 80 ton-force.

Difference from rig UPA-60A:• has higher carrying capacity: max load at hook - 800kN (ton-force).

The following rig components were improved: • construction of tower, rig’s frame and hoist frame was reinforced;• hoist brake system was redesigned to provide more effective braking;• hook-block was replaced with reinforced travelling block.

Well major repair teams requirements are met as much as possible during complex repair works.

The set additionally includes the following units:Wellhead operation platform, manifold riser unit, swivel VB80, stem, drill hose, mechanical rotary table unit.

The rig can be additionally equipped with:• pipe racks;• derrickman racks;• emergency electric drive designed to use for tower upper section lowering and putting into over-the-road position when the chassis motor fails;• additional electric-driven compressor for emergency situations;• tower upper section lifting system with hydraulic hoist;• drum for hoist wireline over-crossing;• electronic inclinometer designed to put the rig into level position;• pump block driven from the rig by means of cardan gear.

RIG FOR WELL DEVELOPMENT & REPAIR MOBILE DRILLING RIGS RIG FOR WELL DEVELOPMENT & REPAIR MOBILE DRILLING RIGS

TRAVELLING BLOCK PERFORMANCES (UPA-60A (60x80) & UPA 60/80 continued)

Installation-and-transport baseSafe load at hook, kN (ton-force)max short-term load for UPA-60A(60x80)

chassis KrAZ-65101b, KrAZ-65053-02 or KrAZ-63221600 (60)800 (80)

Tower• Tower height from crown block axis to the ground level, m

Directional telescopic tower with fender at lower section22.0±0.4

Traveling system stringing• Wire diameter, mm• Device drive• Max drive power, kW (hp)• Hook-block lifting speed range

3x425engine of chassis YaMZ-238M2 or YaMZ-238DE2132.4 (180)0.191-1.444

Hoist

• Hoist speed number• Auxiliary hoist• Auxiliary hoist hook load, kN• Auxiliary hoist hook lifting speed, m/s

single-drum with chain gear, two-band breakerand pneumatic clutches of drum engagement4hydraulic or electric of explosion-proof designfrom 12.5 to 35from 0.4 to 0.8

Hoisting rig overall dimensions in over-the-road position(length, width, height), mmHoisting rig fully loaded weight in over-the-road position,kg, no more than:

Total target life, years

14000x2900x4300

24000 - for UPA-60A26200 - for UPA-60A(60x80)9

A80M


Rig A80M Chassis KrAZ- 6322 and Chassis KrAZ- 63221 Travelling Block Permances provided on request.

RIG FOR WELL DEVELOPMENT & REPAIR MOBILE DRILLING RIGS

UPA-80

Rig UPA-80 is self-propelled unit mounted at a special chassis designed on the base of carrier TM-3 and consists of the following basic units:• hoist winch;• tower with mechanization and transmission system.Winch and other purpose units are driven by tractor engine through rig’s transmission.

Design Features:• extended tower height enabling to work with 21 m stalk;• advanced winch brake system (additional hydraulic brake can be installed on customer request);• derrickman platform which enables to conduct round-trip operation with vertical pipe positioning;• usage of auxiliary hydraulic-driven winch;• usage of hydraulic jack to extend tower upper section;• special cross-country platform for mounting attached equipment on the base of tractor K-703TM;• usage of hydro-mechanical gear-box “Allison” in transmission.


Carrying capacity, kN (ton-force), no more thanPlatform

800 (80)

Device drive carrier TM-3propelling engine YaMZ-8481.10 of tractor K-703TMwith power of 257.0 kW (350 hp) at 1900 rpm

Tackle system• Stringing• String diameter in accordance with standard GOST 16853-71• Lifting speed, m/s:- minimum- maximum• Speed number

4x5 (eight strings)

25

0.231.215

Drawworks• Type• Max hoist wireline traction power at drawworks drum, kN

single-drum with chain drive, pneumatic clutch to engage drum122

Brake system:• main• auxiliary (on request)

mechanical, double-band, with shoeshydraulic

Tower• Type• Tower height (from the ground level to crown block axis), m• Lifting stalk length, m

double-sectional, telescopic with open front face29.416-21

Derrickman platform (on request)

Auxiliary winch• safe load at hook, kN, no more than

hydraulic-driven35

Pulling rig overall dimensions in over-the-road posi-tion,mm, no more than:- length- width- height

1905040755030

MOBILE PUMP BLOCK

MOBILE PUMP BLOCK

BNM-16 (Product on request)

Mobile pump block BNM-16 is designed to pump-in clay mudinto borehole during oil- and gas-well drilling, as well as torquetransfer from pump block to tower block of rig of UPA type(rig A50M) during operation in pair.The block is designed for operation in conditions of temperate andcold macroclimate districts under ambient air temperature from-45’ C to +40’ C


Mounting and transoprtation platform chassis KrAZ-65053or KrAZ-63221.0000044

Power drive installed power, kW (hp)Flushing pump:• type• number• max pressure, MPa (kg/cm’)• max volume supply, 1/s (m’/h)

NB-125-16216 (160)18.0 (64 8)

Pump block overall dimensions, mm, no more than:• length• width• height

1080031503380

Drawworks• Type• Max hoist wireline traction power at drawworks drum, kN

single-drum with chain drive, pneumatic clutch to engage drum122

Brake system:• main• auxiliary (on request)

mechanical, double-band, with shoeshydraulic

Tower• Type• Tower height (from the ground level to crown block axis), m• Lifting stalk length, m

double-sectional, telescopic with open front face29.416-21

OIL FIELD EQUIPMENTWRENCHES

&TONGS

OIL FIELD EQUIPMENT: WRENCHES & TONGS

KT

Chain wrenches of KTs type are designed for manual coupling/uncoupling pipesof oil grade. Depending on operation situation the wrench can be used with or withoutremovable extension which is mounted on wrench handle without effort.

It has the following advantages over KTsN type wrenches:• less wrench weight of the same dimension-type.• slip life is 2 times longer• one KTS type wrench replaces 2 wrenches of KTsN and KTsO types of the same dimension-type.• less wrench dimensions.

Specifications KTs 48-114 KTs 114-146 KTs 146-245

Passage diameter of pipes to be coupled/uncoupled, mm 48-114 114-146 146-245

Safe load at the end of the handle with extension, kg 100 130 150

Length without extension, mm 500 965 1100

Length with extension, mm 1035 1500 2000

Length, mm 90 115 170

Weight, kg 6.2 10.5 26

KTGU-M (TU 26-02-1039-87)

Chain wrenches of KTs type are designed for manual coupling/uncoupling pipesof oil grade. Depending on operation situation the wrench can be used with or withoutremovable extension which is mounted on wrench handle without effort.

It has the following advantages over KTsN type wrenches:• less wrench weight of the same dimension-type.• slip life is 2 times longer• one KTS type wrench replaces 2 wrenches of KTsN and KTsO types of the same dimension-type.• less wrench dimensions.

Specifications KTGU-M-60 KTGU-M-73 KTGU-M-89

Passage diameter of pipes to be coupled/uncoupled, mm 60 73 89

Max torque, kNm 3.0 3.5 4.5

Overall dimensions, mm, no more than 332x142x65 344x154x74 382x187x74

Complete set weight, kg 4.3 5.3 7.3

KTsN, KTsO (TU 26-02-335-76)

Wrenches for tubing string KTsN and KTsO are designed for gripping androtating oil grade pipes during coupling/uncoupling for use under conditionsof temperate and cold (region L2) macroclimate regions in accordance with standardGOST 16350-80.

Specifications KTs0-1 KTSsN-1 KTsN-2 KTsN-3

Passage diameter of pipes to be coupled/uncoupled, mm 60-114 60-114 114-146 146-245

Max torque, kNm 1.1 1.1 1.8 2.9

Safe load at the end of the handle with extension, N 1660 950 1150 1400

Overall dimensions, mm 660x105x110 1160x105x110 1570x112x135 2100x140x165

Weight, kg 10 14 24 53


APR2-VBM (TU 26-02-1060-87)

(Automatic) tongs for well underground repair APR2-VBM is designed to mechanizecoupling/uncoupling operations, suspend and release tubing strings duringunderground repair under conditions of temperate and cold (region L2) macroclimateregions in accordance with standard GOST 16350-80.

Specifications

Spider carrying capacity, ton 80

Passage diameter of pipes to be coupled/uncoupled, mm 48, 60, 73, 89, V48, VB60, V73, V89

Max torque, kNm (kgf-m) 4.5 (450)

Rein speed, s·1 (rpm), no less than 0.85 (51)

Drive motor electric motor AIM 1005 4U2,5

Power consumption, kW, no more than 3.0

Complete automatic tongs weight, kg 240

Complete set weight, kg 310

Overall dimensions, mm 850x460x730

APR2-VBM (TU 26-02-1060-87)

(Automatic) hydrologically-driven tongs for well underground repair APR2-GP isdesigned to mechanize coupling/uncoupling operations, suspend and releasetubing strings during underground repair for operation in complex with rigs (units)equipped with hydraulic drives.The tongs is designed to use under conditions of temperate and cold (region L2)macroclimate regions in accordance with standard GOST 16350-80.

Specifications

Max torque, kNm (kgf-m) 4,5 (450)

Passage diameter of pipes to be coupled/uncoupled, mm 48, 60, 73, 89, V48, V60, V73, V89

Rein speed, s· 1 (rpm), no less than 0.85 (51)


Drive motor hydro-motor G15-24

Tongs hydraulic system pressure, MPa 12.5

Complete automatic tongs weight, kg, no more than 200

Complete set weight, kg, no more than 270


Power consumption, kW, no more than 5.0

KT (TU 3668-003-00217567-97)

Wrenches of KT type are designed to couple/uncouple oil grade pipes and couplingsby gripping their bodies in mechanized or manual way during well repair. Theyare used under conditions of temperate and cold (region L2) macroclimate regionsin accordance with standard GOST 16350-80.

Specifications KT 48-89 KT 89-132

Passage diameter of pipes (couplings) to be coupled/uncoupled, mm 48-89 89-132

Max torque, kNm 3.5 4.5

Overall dimensions, mm 486x130x120 510x140x120

Complete set weight, kg, no more than 8.7 10.4


KShE (TU 26-16-173-84)

Mechanical sucker rod and tubing tongs of KShE type is designed for mechanizedcoupling/uncoupling sucker rods in accordance with standard GOST 13877-80during trip operations under routine repair, under conditions of temperate and cold(region L2) macroclimate regions in accordance with standard GOST 16350-80. Tongdrive is electrical supplied from field electric mains. Electric motor V71V4 has explosion-proof design.

Specifications

Rated axial power, kN 100

Passage diameter of sucker-rods in accordance with standard GOST 13877-80, mm

16, 19, 22, 25

Max torque, Nm 980

Rein speed, s·1 (rpm), no less than 100

Power consumption, kW, no more than 0,75

Mains voltage, V 380

Complete tongs weight, kg 60



KSM (TU 26-16-101-79)

Stoppers for tubing strings KSM are used to stop tubing strings during theirmechanized coupling/uncoupling at well routine repair.They are designed to use under conditions of temperate and cold (region L2) macroclimateregions in accordance with standard GOST 16350-80.

Specifications KSM-60 KSM-73 KSM-89

Passage diameter of pipes to be coupled/uncoupled, mm 60 73 89

Diameter of couplings to be stopped, mm 73 88,9 108

Max torque, Nm (kg-force-m) 2450 (250) 2940 (300) 3430 (350)

Overall dimensions, mm 210x190x140 250x205x143 270x240x160

Complete set weight, kg 5.5 7.4 m

PBK-4 (TU 26-06-80-83)


Pneumatic-driven suspended tongs PBK-4 is designed to couple, torque anduncouple drill and casing pipes during borehole drilling by rotary or turbine motorway.The tongs designed to use under conditions of temperate macroclimate regionin accordance with standard GOST 16350-80.

Passage diameter of pipes to be coupled/uncoupled, mm: - drill pipes 73-168

- casing pipes 114-245

Motor power, kW 5.5

Drive power, kW 11

Tongs weight, kg 670



KMP-G (TU 3666-017-00217567-2003)

Hydraulic-driven mechanical suspended tongs KMP-G is designed tocouple/uncouple tubing strings and drill pipes during trips under well routine andmajor repair as a part of pulling rigs such as A-50, UPA-60 and others.The tongs is designed to be used under conditions of temperate and cold (regionL2) macroclimate regions in accordance with standard GOST 16350-80 at ambientair temperature from -40° C to +50° C.The tongs design has high torque, reliability and long service life and is easy in operationand servicing.

Specifications

Torque at rotor at corresponding

discharge pressure, kNm (kg-force-m): - minimum 0.57 (57)

- rated 8 025 (803)

- maximum 11.5 (1150)

Gripping device speed under load, s·1 - at top gear 0.12-1.66

- at lowest gear 0.05-0.83

Passage diameter of pipes to be coupled/uncoupled, mm 60, 73, 89

Rated pressure, MPa (kg/cm’) 14 (140)

Max pressure, MPa (kg/cm’) 20 (200)

Min pressure, MPa (kg/cm’) 3 (30)

Torque arm, mm 700

Overall dimensions, mm: - with stopper 1140x770x1000

- without stopper 1140x770x640

Set weight, kg: - with stopper 380

- without stopper 330


KMU-50M (TU 26-16-119-80)

Multi-purpose mechanical tongs KMU-50M is designed to mechanize operationsof coupling/uncoupling and retaining tubing strings in suspended position duringrouting and major repair of wells operated with all equipment types including electro-loadingpumps and to be used under conditions of temperate and cold (regionL2) macroclimate regions in accordance with standard GOST 16350-80.

Specifications


Passage diameter of pipes to be coupled/uncoupled, mm 48, 60, 73, 89

Rein speed, s’(rpm), no less than 1 (60)

Max torque, kNm 4.7

Drive motor electric motor AIM 1005 4U2,5

Complete tongs weight, kg 360



KMU-GP-50M (TU 26-16-119-80)

Multi-purpose mechanical tongs KMU-GP-SOM is designed to be used as a partof hydroficated pulling rigs such as A-SOM to mechanize operationsof coupling/uncoupling and retaining tubing strings in suspended position duringrouting and major repair of wells operated with all equipment types includingelectro-loading pumps. The tongs are designed to be used under conditions of temperateand cold (region L2) macroclimate regions in accordance with standard GOST16350-80.

Specifications

Max torque, kNm 4,7

Passage diameter of pipes to be coupled/uncoupled, mm 48, 60, 73, 89

Rein speed, s·1 (rpm), no less than 1 (60)


Drive motor hydro-motor G 15-24

Complete tongs weight, kg, no more than 350



OIL FIELD EQUIPMENT: SWIVELS

OIL FIELD EQUIPMENTSWIVELS


VE (TU 3666-021-00217567-2002)

Operational swivel VE is designed to provide rotation of drill stalks and supplyflushing fluid during well repairs under conditions of temperate and cold (region L2)macroclimate regions in accordance with standard GOST 16350-80.

Specifications VE-50 VE-60 VE-80

Carrying capacity, ton 50 60 80

Working pressure, Pw, MPa 16 16 20

Stem flow diameter, mm 60 60 75

Complete set weight, kg 205 200 435

Overall dimensions, mm 1410x412x390 1410x412x390 1735x580x606

Swivel stem speed, s·1 (rpm), no more than 1.66 (100) 1.66 (100) 2 (120)

Connecting thread:

- at swivel stem for fitting (sub), in accordance with standard GOST 631-75, mm 89, left-hand* 89, left-hand* 114, left-hand*

- at fitting for drill pipe pin, in accordance with standard GOST 5286-75, mm 3-88, left-hand* 3-88, left-hand* 3-121, left-hand*

- at cover side pin, in accordance with standard GOST 633-80, mm 73 73 89

* There is possibility to manufacture swivels with right-hand threads on customer request.

VP (TU 3666-007-00217567-2001)

Flushing swivels VP are designed to supply flushing fluid from pump to boreholebottom and to provide rotation of pipes during repair of oil- and gas-wells underconditions of temperate macroclimate region in accordance with standard GOST16350-80.

Specifications VP-60 VP-80

Carrying capacity, ton 60 80

Pumped fluid pressure, MPa, no more than 16 20

Stem passage diameter, mm 50 75

Thread in accordance to standard GOST 633-80, mm: - at stem ends 73 left-hand* 114 left-hand*

- at branch 73 89

Stem speed, s·1 (rpm) 1.66 (100) 1.66 (100)

Overall dimensions, mm 730x270x170 880x410x210

Complete set weight, kg 60 137

* There is possibility to manufacture swivels with right-hand threads on customer request.


AR60 (TU 3666-021-00217567-2002)

Swivel AR60 is designed to be used in rigs with carrying capacity up to 60 ton-force.

Specifications

Carrying capacity 600 kN (60 ton-force)

Passage diameter 60 mm

Working pressure 16 MPa (160 kgf/cm')

Swivel overall dimensions 1310x400x500 mm

VB-80 (TU 3661-015-00217567-2001)

Drilling swivel VB-80 (VB-80.00.000 sb) is designed to supply flushing fluid frompump to borehole bottom at rotary and turbine motor drilling and to providerotation of drilling string under conditions of temperate and cold (region L2)macroclimateregions in accordance with standard GOST 16350-80.

Specifications

Carrying capacity, ton 80

Working pressure of pumped fluid, MPa, no more than 20

Stem speed, s·’ (rpm), no more than 3.33(200)

Stem passage diameter, mm 60

Sub connecting thread

in accordance with standard GOST 5286-75, mm 3-121L

Overall dimensions, mm, no more than: - width at inlet flange 580

- width at lifting eyes 700

- width at bail axis 476

- height 1250

Weight, kg, no more than: - complete swivel 490

- complete set 510

OIL FIELD EQUIPMENT: SWIVELS OIL FIELD EQUIPMENT: SWIVELS

VB-80 A60/80M1

Swivel VB 80 (A60/80M1.40.00.000 sb) is designed to provide free rotationof drilling equipment suspended to tackle block and to supply flushing fluid to boreholebottom through drilling string.

Specifications

Static carrying capacity, kN (ton-force) 785 (80)

Passage diameter, mm 75

Working fluid pressure, MP a (kg/cm'), 19.6 (200)

Overall dimensions, mm, no more than 1750x460x490

BU-50BR-16SB (TU 26-02-255-77)

Swivel VB 80 (A60/80M1.40.00.000 sb) is designed to provide free rotationof drilling equipment suspended to tackle block and to supply flushing fluid to boreholebottom through drilling string.

Specifications

Carrying capacity, ton 50

Working pressure, Pw, MPa 15

Stem flow diameter, mm 103

Stem speed, s·1 3.33

Sub connecting thread in accordance with standard GOST 5286-75, mm

3-147L



OIL FIELD EQUIPMENTROTARYTABLES

OIL FIELD EQUIPMENT: ROTARY TABLES

ROTARY RIG

Rotary rig (A60/80.14.00.000 sb) it is designed to rotate drilling tools by meansof chain drive and retain pipe string suspended during well major repair as a partof rigs of A50M type.Reversible drive depending on asterisk setting on the top or bottom roll.

Specifications A60/80.14.00.000 sb A60/80.14.00.000sb-01

KA60/80.14.00.000 sb-02

A60/80.14.00.000 sb-03

Max static load to table, ton-force 60 60 80 80

Table passage diameter, mm 250 250 410 410

Rotary table weight, kg 915 750 1415 1250

R-410

Rotary table 410 (A60/80.11.00.000A sb) is designed to complete units AR60,A60/80.Rotary table 410 (ba15-3A sb) is designed to complete units BA15, URB3A3. reversible drive depending on asterisk setting on the top or bottom roll.

Specifications AR60 A60/80 BA15

Max torque at the table, Nm (kg-force-m) 11772 (1200) 11772 (1200) 7840 (800)

Rotational speed, s·1 (rpm) 0.67 (40) - 4 (240) 0.67 (40) - 4 (240) 1.08 (65) - 4.22 (253)

Static carrying capacity, kN (ton-force), no less than 589 (60) 785 (80)

Dimensions of the main pipe insert, mm 80x80 or 112x112 80x80 or 112x112 80x80 or 112x112

R-250

Rotary table 250 (A60/80.11.00.000A sb-01) is designed to complete AR60,A60/80.

Specifications AR60 A60/80

Max torque at the table, Nm (kg-force-m) 9810 (1000) 9810 (1000)

Rotational speed, s·1 (rpm) 0,83 (50) -5 (300) 0,83 (50) -5 (300)

Static carrying capacity, kN (ton-force), no less than 589 (60) 785 (80)

Dimensions of the main pipe insert, mm 80x80 or 112x112 80x80 or 112x112

HYDRAULICALLY-DRIVEN ROTARY TABLE


Hydraulically-driven rotary table (ASOM.04.00.000 sb “i”) is designed for drilling(including cement plug drilling), as well as mechanical coupling and uncoupling ofdrill pipes and tubing strings under conditions of temperate macroclimate region inaccordance with standard GOST 16350-80. Climatic design “U”, ambient air temper-aturefrom -45’ C to +40’ C.

Specifications

Max torque, kNm (kg-force-m) 6.3 (630)

Max static load to table, ton-force, no more than 600 (60)

Rotary speed, s·1 (rpm), no more than: - 1st mode 0.372 (223)

- 2nd mode 0.75 (45)

- 3rd mode 1.185 (70)

Passage diameter of pipes to be coupled/uncoupled, mm 60, 73, 89

Table passage diameter, mm 142

Hydraulic system pressure, MPa (kg/cm’), no more than 10 (100)

Rotary table control from control panel of pulling rig UPA-60

Rotary table overall dimensions, mm, no more than: - length 890

- width 860

- height 906


HYDRAULICALLY-DRIVEN ROTARY TABLE

Hydraulically-driven rotary table R-250 (ASOM.04.00.000 sb) is designedto rotate drilling tools and retain pipe string suspended during drilling operations.The rotary table is designed to be used as a part of rig A60/80 and other rigs whichhave hydraulic station with adequate power and is installed at string flange.

Specifications

Max static load to table, ton-force 50

Table passage diameter, mm 250

Diameter of rief stem bush passage diameter, mm 80x80

Rotary table gear set ratio 4.92

Gear-box gear set ratio 6.67

Hydraulic system rated pressure, kg-force/cm’ 100

Rated working fluid consumption, I/min up to 350

Max torque, kg-force-m 1000/500

Max rotary table speed, rpm 45/90


Rotary table weight, kg 810


RU-80x400

RGP250

Specifications on request.




PR-250

PR-250



OIL FIELD EQUIPMENTFISHING TOOLS

OIL FIELD EQUIPMENT: FISHING TOOLS

K (TU 26-16-284-90)

Bell sockets of K type is designed for gripping by cutting onto outside surface andsubsequent removal of stuck drill or tubing string from well.The bell sockets are designed to be used in all macroclimatic areas in accordancewit h standard GOST 16350-80.

Specifications

Code Top-joint thread dimensions ac-cording to GOST 7918-75 5286-75

Min fishing thread passage diameter mm.

Rated axial load,kN

Min casing string passage diameter to be captured, mm

Weight, Kg Overall dimensions, mm

Length Pipe outer diameter

K 42-25 (L) * 3-50 25 250 114 6.5 385 65

K 50-34 (L) * 3-50 34 350 114 5.0 340 65

K 58-40 (L) 3-66 40 450 114 15.0 490 90

K 70-52 (L) 3-66 52 650 114 14.0 510 90

K 85-64 (L) 3-76 64 750 127 18.0 550 102

K 100-78 (L) 3-88 78 850 146 26.5 595 122

K 110-91 (L) 3-101 91 1000 168 26.5 555 132

K 125-103 ( L) 3-121 103 1100 194 31.0 560 148

K 135-113 (L) 3-133 113 1250 219 41.0 635 170

K 150-128 (L) 3-147 128 1350 245 70.0 655 194

K 174-143 (L) 3-171 143 1500 273 98.0 800 220

MBU (TU 26-16-281-90)

Fishing taps for drill strings of MBU type are designed for gripping byplunge cutting into increased components of stuck string and subsequent removalof drill string from well.The taps are used in all macroclimatic areas in accordance with standard GOST16350-80

Specifications

Code Top-joint thread dimensions ac-cording to GOST 7918-75 5286-75

Min fishing thread passage diameter mm.

Rated axial load,kN




MBU 20-45 (L) 3-66 20 160-300 114 8 680 80

MBU 22-54 (L) 3-76 22 220-420 127 13 795 95

MBU 32-73 (L) 3-88 32 300-640 140 24 955 108

MBU 58-94 (L) 3-102 58 560-820 168 34 875 120

MBU 74-120 (L) 3-147 74 760-1150 219 75 1090 178

MBU 100-142 (L) 3-171 100 1100-1400 273 95 1030 203

MBU 127-164 (L) 3-171 127 1150-1450 273 114 930 220

* = on request

OIL FIELD EQUIPMENT: FISHING TOOLS OIL FIELD EQUIPMENT: FISHING TOOLS

MES (TU 26-16-275-89)

Special fishing tap MES is designed for gripping by plunge cutting into collarthread and subsequent removal of stuck tubing string terminated with collar fromwell.The tap is designed to be used in all macrocli matic areas in accordance with standardGOST 16350-80.

Specifications

Code Tool-joint thread dimensions ac-cording to GOST 5286-75

Fishing thread passage diameter to GOST 633-80, mm

Rated axial load, kN




MES-60 * 3-76 60 560 114 7.6 260 90

MES-V60 * 3-76 V60 560 127 8.2 260 90

MES-73 * 3-76 73 760 146 7.3 260 90

MES-V73 * 3-76 V73 760 178 8.0 260 90

MES-89 3-88 89 1090 140 10.2 260 108

MES-V89 * 3-88 V89 1090 219 11.3 260 108

* = on request

MEU (TU 26-16-275-89)

Tubing fishing taps MEU are designed for gripping by plunge cutting inside collarand pipe and subsequent removal of stuck tubing string terminated with collar.Th e tap can also be used for gripping string by pipe’s up set and subsequent removalof string.The taps are used in all macrocli matic regions in accordance to GOST 163 50-80.

Specifications

Code Tool-joint thread dimensions ac-cording to GOST 5286-75

Min fishing thread passage diameter, mm

Max fishing thread passage diameter, mm

Rated axial load, kN




MEU 36-60(L) 3-50 36 60 300 114 6,5 370 65

MEU 48-80(L) 3-76 46 80 450 114 11 455 90

MEU 69-l00(L) 3-88 69 100 600 140 19 450 108

MEU 85-127(L)

3-117 85 127 750 168 34 560 134

LShPM2 (TU 3668-004-00217567-99)

Specifications LShPM2-73 LShPM2-89

Diameter of tubing strings in which fishing is taken place, mm 73 89

Diameter of sucker rods to be fished, mm 16, 19 16, 19, 22

Max safe koad at fi shing tool, kN 40 55

Rod connection thread in accordance to GOST 13877-80 Sh19 Sh22

Overall dimension s, mm, no more than:

- outer diameter 56 68

- length 1820 1950

Complete set weight, kg, no more than 7 12

Modernized plunger-type rod-fishing tools LShPM2 are designed for fishingof unscrewed or fallen but not stuck sucker rods inside tubing during the routinewell repair. These fishing tools are designed to be used in all macroclimatic regionsin accordanc e to GOST 16350-80.

OIL FIELD EQUIPMENTANCHOR, BAILS

OIL FIELD EQUIPMENT: ANCHOR, BAILS

BAILS ShE (TU 3668-009-00217567-2000)

Special fishing tap MES are designed to suspend elevators to hooks of tackle system duringlifting/lowering operations at overhaul repair of oil- and gas-wells.Bails SHE are designed to be used in moderate and cold macroclimatic regionsin accordance with standard GOST 16350-80.

Specifications ShE-28 ShE-32 ShE-50 ShE-60 ShE-80

Carrying capacity of bail set pair, ton-force 28 32 50 60 80

Cross-section diameter, mm 35 40 45 50 60

Bail overall dimensions, mm: - length 860±10 860±10 920±10 920±10 1200±10

- width 230±10 240±10 250±10 260±10 250±10

Complete set weight, kg, no more than 30 38 52 63 112

OIL FIELD EQUIPMENTELEVATORS

OIL FIELD EQUIPMENT: ELEVATORS

EN (TU 26-02-258-77)

Cast elevators for casing pipes of EN are designed for gripping and holdingcasing string suspended during lowering and lifting operations in course of welldrilling. These elevators are designed to be used in moderate macroclimatic regionin accordance with standard GOST 16350-80.

Specifications EN-194-160 EN-219-160 EN-245-160 EN-325-160 EN-426-160

Carrying capacity, ton 160 160 160 160 160

Pipe passage diameter, mm 194 219 245 325 426

Diameter of hole for pipe, mm 198 224 250 331 433

Overall dimensions, mm 940x352x365 965x382x365 995x412x365 1095x502x365 1195x602x365

Set weight, kg 180 220 235 290 354

SPG-80 (TU 3666-017-00217567-2003)

Spider SPG-80 is designed for gripping and holding suspended tubing and drillpipes during lowering and lifting operations in course of well repair as a partof hydraulic or compressor-equipped pulling rigs of UPA-60A type and as a partof A50MB during drilling under conditions of moderate and cold (region L2) macroclimaticregions in accordance with standard GOST 16350-80.

Specifications

Safe load, kN (ton-force) 800 (80)

Wedge block drive hydraulic or pneumatic

supplied from pulling rig

Rated working pressure, mpa:

- of hydraulic system 10.0

- of pneumatic system 0.6-0.9

Rassage diameter of caught pipes, mm:

- tubing ones in accordance with GOST 633-80 60, 73, 89

- drill ones in accordance with GOST 631-75 60, 73, 89

Overall dimensions, mm, no more than:

- length 650

- width 580

- heigh 450

Weight, kg, no more than:

- of complete spider 210

- of complete set 223


ETAD (TU 3668-006-00217567-99)

Casing doublebail elevator ETAD with automatic looking device is designed for gripping from under collar or lock and holding tubing or drill strings suspended during lowering and lifting operations with upright tube installation and tubing racking in course of development and repair or oil- and gas-wells.The elevator is used under conditions of moderate and cold macroclimatic regions in accordance with standard GOST 16350-80.

4 gripping variations

Specifications ETAD-80 ETAD-100

Max carring capacity, ton 80 100

Rassage diameter of caught pipes, mm 73, V73, N73, 89, V89, N89 73, V73, 89, 114

102, V102, 114, V114, B89

Overall dimensions, mm (length-width-height) 510x310x220 510x310x240

Complete set weight, kg, no more than 96 103

ETA, ETA-P (TU 26-16-287-90)

Elevators of ETA and ETA-P types are designed for gripping from under collar or lock and holding of tubing or drill strings suspended during lowering and lifting oper-ations with upright tube installation and with tubing racking in course of development and repair of oil- and gas-wells.The elevators are used under conditions of modern and cold (region L2) macroclimatic regions in accordance with standard GOST 16350-80.

Specifications ETA-32 * ETA-50 ETA-60

Max carring capacity, ton 32 50 60

Rassage diameter of caught pipes, mm 48, V48, 60 60, V60, 73 60, V60, 73

V60, 73, V73 V73, 89 V73, 89

Overall dimensions, mm (length-width-height) 280x200x540 290x230x575 300x240x590

Weight, kg 34 36 41

Specifications ETA-32P * ETA-50P ETA-60P

Max carring capacity, ton 32 50 60

Rassage diameter of caught pipes, mm 48, V48, 60 60, V60, 73 60, V60, 73

V60, 73, V73 V73, 89 V73, 89

Overall dimensions, mm (length-width-height) 296x200x540 300x230x560 300x245x590

Weight, kg 32 39 44

* = on request

CATWALK SYSTEMS&

RAMPS

OIL FIELD EQUIPMENT: ELEVATORS CATWALK SYSTEMS, RAMPS

CATWALK SYSTEMS

Slide catwalk attachment A60/80.110.00.OOOSB flat, collapsible horizontal drilling, oil-welltubing and turbo drill.

Catwalk pipe rack for flat, collapsible horizontal drilling, oil-well tubing and turbo drill.

Catwalk pipe rack for flat, collapsible horizontal d ri l ling, oil-well tubing and turbo drill.

RAMPS

Sectional ramp for UPA-60A, UPA-60/80, A60/80, A60/80M. Multiple oil-well plat-forms during drilling, well testing and well repairs with high casing head Suitable for microclimatic areas with temperature fluctuation fro m -45 ° C to+ 45° C.

Mobile hoist unit ramp UPA-60A, UPA-60/80, A60/80, A60/80M. Multiple oil-well platforms during drilling, well testing and well repairs with high casing head . Suitable for microclimatic areas with temperature fluctuation from -45 ° C to + 45° C.


OVERFLOW VALVES

OVERFLOW VALVES

Overflow valves

Overflow valve is installed above downhole drilling motor and is designed to fill and draindrill strings in course of lifting and lowering operations.

Overflow valves specifications

Outer diameter, mm Length, mm Connection threads to the drill string

Pressure difference at triggering, kfm/sm 2

KP 105.000 106 320 3-88 2,1 ± 0,2KP 127.000 127 340 3-101 2,1 ± 0,2KP 172.000 172 415 3-147 2,1 ± 0,2KP 195.000 195 450 3-147 2,1 ± 0,2KP 240.000 240 525 3-171 2,1 ± 0,2

DOWNHOLD DRILLING MOTORS, TURBO DRILLS, TURBO DRILLS - WHIPSTOCKS,

DRILLS

SPARE PARTS FOR OIL FIELD EQUIPMENT

DOWNHOLD DRILLING MOTORS, TURBO DRILLS, TURBO DRILLS - WHIPSTOCKS, DRILLS

IMZ GROUP LIMITED produces a wide range of hydraulic downhole motors (HDM) including the downhole drilling motorsand turbodrills within the range of76-240 mm for the vertical, directed (D type) and horizontal drilling, maintenanceand repair work (DU type). It produces the overflow valves for the downhole drilling motors having the size of 106-240 mmas well as the reactive turbine drillers with the diameter of 394-2600 mm.

Product design features:

- Optimum length, high stiffness, controllability and reliability- Downhole drilling motors configuration with angle regulators with the thrust bearing dressing in the touchdown pointwith the hole wall- Provision of motors with the increased reliability hard-alloy bearings, swivelling device, bearings made of the siliconand molybdenum steel with the increased lift capacity.

IMZ GROUP LIMITED offers a wide range of services:

-Hydraulic downhole motors leasing and delivery to the lessee-Work using the modern equipment for the hydraulic downhole motors repair-Immediate repair and equipment delivery to the Customer-Engineering support in case of repair and drilling-Efficient staff-Engines configuration and spare parts to them-Usage of modern equipment for engine assembly and delivery to the Customer ready for work

The high quality of the downhole motors is provided by the effective work in accordance with the quality systemISO 900 l :2000. We constantly improve our design in accordance with the wishes of our Customer supplyingadvanced and modern equipment.

DOWNHOLD DRILLING MOTORS, TURBO DRILLS, TURBO DRILLS - WHIPSTOCKS, DRILLS DOWNHOLD DRILLING MOTORS, TURBO DRILLS, TURBO DRILLS - WHIPSTOCKS, DRILLS

Specifications of downhole drilling motors with diameters of 76 - 106 mm

Parameter

DU

76.

4/5.

20

DU

-85

D-8

8

DU

-88

D-9

5.5/

6.30

D-9

5.6/

7.30

DU

-95P

.5/6

.30

DU

-95P

.6/7

.30

DU

1-95

P.5/

6.30

DU

1-95

P.6/

7.30

DU

-95P

K.6

/7.1

2

D1-

105

DU

-05

Housing outer diameter, mm 76 85 88 95 95/106 95 106

Start of operating units, Zp/Zc 4/5 5/6 5/6 6/7 5/6 6/7 5/6 6/7 5/6

Length, mm, tolerance:- motor without valve, ±3%

- spindle prior to curvature, ±3%- stator active section, ±0.2%

4240-2000

373010401220

3730-1220

373010401220

5290-

3000

529013233000

566514003000

330010501200

3770-1500

396017001500

Drift angle between sections, degree - 0°-3° - 0°-3° - - 0°-3° - 0°-2°

Connection threads in accordancewith standard GOST 5286:

- to chisel- to drill pipes

3-663-66

3-763-76 (3-73)

3-763-88

Recommended diameters of chisels used, mm

83,0-98,4 98,4-120,6 112,0-123,8 120,6 - 151,0

Drilling agent consumption, L/sec 3-5 5-7 5-10 6-10

Output shaft torque, kNm:- braking mode

- max operating moment0,9-1,00,6-0,8

1,0-1,20,8-1,0

2,0-2,91,6-2,4

2,4-3,62,0-3,0

2,0-2,91,6-2,4

2,4-3,62,0-3,0

2,0-2,91,6-2,4

2,4-3,62,0-3,0

1,1-1,60,6-0,9

1,3-1,81,1-1,4

Output shaft rotation speed, sec’:- idling mode

- operating mode3,3-6,23,0-5,0

3,4-6,32,7-5,0

4,2-8,42,7-5,4

1,4-2,60,9-1,8

4,2-8,42,7-5,4

1,4-2,60,9-1,8

4,2-8,42,7-5,4

1,4-2,60,9-1,8

1,6-2,81,0-2,0

3,2-5,32,6-3,8

Pressure difference, MPa:- idling mode

- operating mode- braking mode

3,1-4,27,0-9,08,0-11,0

1,5-2,05,8-7,08,7-9,0

2,2-4,06,5-11,013-15,5

1,2-2,53,5-7,06,8-10,0

2,2-4,06,5-11,013-15,5

1,2-2,53,5-7,06,8-10,0

2,2-4,06,5-11,013-15,5

1,2-2,53,5-7,06,8-10

0,7-0,91,5-2,02,7-4,5

1,3-1,95,0-8,08,0-12,0

Allowable axial load, kN, not more 25 30 50 60 50 60



Parameter

D1-

106

DU

1-10

6P.7

/820

D1-

106.

9/10

.20

DU

1-10

6P.9

/10.

20

DU

1-10

6P.5

/6.3

0

DU

1-10

6P.7

/8.3

0

DU

-120

P.6/

7.30

D-1

27.7

/8.3

0

DU

-127

P.7/

8.30

D2-

127

D-1

27.9

/10.

20

DU

-127

P.9/

10.2

0

Housing outer diameter, mm 106 120 127

Start of operating units, Zp/Zc 7/8 9/10 5/6 7/8 6/7 7/8 9/10



4240-2000

441513602000

4240-2000

441513602000

541513603000

609013233000

6300-3000

630015253000

5820-2000

5800-2000

580015252000

Drift angle between sections, degree - 0° -2°30/ - 0° -2°30/ 0°-3° - 0°-3° - 0°-3°



3-763-88

3-883-102

3-883-102

3-883-101

Recommended diameters of chisels used, mm 120,6-150,0 139,7- 165,1 151,0-165,1

Drilling agent consumption, L/sec 6-10 6-12 4-12 6-12 4-12 10-20 15-20



1,5-3,41,2-3,2

2,7-4,52,1-3,5

2,8-5,52,2-4,5

3,1-3,52,8-3,2

3,1-3,54,0-5,5

3,6-4,12,9-3,3



3,5-4,21,3-2,6

1,6-2,50,6-1,9

2,8-4,82,2-3,8

3,3-4,01,1-2,5

3,0-5,22,4-4,8

2,3-5,01,5-3,2

3,6-4,72,9-3,8



1,3-2,55,0-10,07,5-15,0

1,9-3,54,0-6,58,0-9,7

1,6-3,04,5-6,04,3-8,2

2,0-3,86,0-8,09,5-10,9

6,0-8,39,0-9,9

2,2-2,84,5-9,010,5-12,0

1,7-3,15,0-9,0

10,0-13,2

1,8-2,37,0-9,0

10,5-13,5

Allowable axial load, kN, not more 60 80 100



Parameter

D3M

1-17

2

D5M

1-17

2

D3M

-172

D5M

-172

D3M

-176

DU

-176

P.6/

7.24

D5M

-176

D3M

1-17

6

DU

-176

P.9/

10.2

4

D5M

1-17

6

DU

1-17

6P.6

/7.2

9

DU

1-17

6P.9

/10.

29

D-1

78.6

/7.4

0

D-1

78.9

/10.

40

Housing outer diameter, mm 172 176 178/195 178/195

Start of operating units, Zp/Zc

6/7 9/10 6/7 9/10 6/7 9/10 6/7 9/10



6235-2400

6720-2900

6235-2400

6720-2900

6235-2400

590020852400

6750-2900

6235-2400

590020852400

6750-2900

640020802900

640020802900

8180-4000

8180-4000

Drift angle between sections, degree

- - - - 0°-2°30’ - - 0°-2°30’ - 0°-2°30’ - -

Connection threads in accord-ance

with standard GOST 5286:- to chisel

- to drill pipes3-1173-147

3-1173-147

3-1173-147


190,5 - 215,9 190,5-215,9 190,5-215,9

Drilling agent consumption, L/sec

25-35 25-35 25-35



10-149,0-12,0

9,6-12,47,7-9,9

13-1610-13

7,4-9,65,9-7,7

10-14 9-12

10-128-10

13-1610-13

10-149-12

13-1610-13 12-18 14-20

Output shaft rotation speed, sec’:

- idling mode- operating mode

4,7-5,53,8-4,4

4,2-5,13,4-4,0

1,9-2,51,4-1,9

1,9-2,51,5-2,0

4,7-5,53,8-4,4

4,2-5,13,4-4,0

1,9-2,51,4-1,9

1,9-2,51,5-2,0

4,2-5,13,4-4,0

1,9-2,51,5-2,0

4,2-5,03,4-4,0

1,9-2,51,5-2,0



2-39-1313-19

2,5-3,59-1313-20

1,6-2,56,5-1010-14

2,5-310-1214-17

2-39-13

13-19,5

2,5-3,59-1313-20

1,6-2,56,5-1010-15

2,5-310-1215-18

9-1313-20

10-1215-18

10-1513-20

11-1415-18

Allowable axial load, kN, not more

200 200 200


Specifications of downhole drilling motors with diameters of 195 mm

Parameter

D4M

-195

D4M

-195

C.6

/7.2

4

DU

-195

P.6/

7.24

D5M

1-19

5C.6

/7.2

9

DU

-195

P.6/

7.29

D3M

-195

D3M

-195

C.9

/10.

24

DU

-195

P.9/

10.2

4

D2M

-195

C.9

/10.

29

DU

-195

P.9/

10.2

9

DU

-195

.6/7

.40

D-1

95.9

/10.

40

Housing outer diameter, mm 195

Start of operating units, Zp/Zc 6/7 9/10 6/7 9/10



6800-2400

6700-2400

760033252400

7220-2900

810033252900

6790-2400

6700-2400

760033252400

7220-2900

810033252900

8310-4000

8310-4000

Drift angle between sections, degree - 0°-3° - 0°-3° - - 0°-3° -



3-1173-147


215,9-244,5

Drilling agent consumption, L/sec 25-35



10,0-14,09,0-12,0

9,6-12.47,7-9,9

12,9-16.410,3-13,1 12-18 14-20


- operating mode4,7-5,53,8-4.4

4,2-5,13,4-4,0

1,9-2,51,4-1,9

1,9-2,51,5-2,0

4,2-5,03,4-4,0

1,9-2,51,5-2,0



8,8-13,013,2-19,5

9,0-13,013,2-20,0

6,5-9,89,8-14,7

9,8-11,814,7-17,7

10,0-15,513,2-20,0

10,9-13,914,7-17,7

Allowable axial load, kN, not more 250


Specifications of downhole drilling motors with diameters of 240 mm

Parameter

D1-

240

D-2

40.7

/8.3

0

DU

-240

P.7/

8.30

Housing outer diameter, mm 240

Start of operating units, Zp/Zc 7/8



6930-3000

7300-3000

816037203000

Drift angle between sections, degree - - 0°-3°


- to chisel- to drill pipes 3-117

3-147

Recommended diameters of chisels used, mm 269,9-444,5

Drilling agent consumption, L/sec 30 - 50







1,5-3,06,0-8,08,0-12,0

Allowable axial load, kN, not more 300


Turbodrills and turbodrills-whipstocks.

Turbodrills and turbodrills-whipstocks are designed for drilling of vertical, directional oil and gas wells aswell as for shaft and sidetracking in case of emergency and drilling of large holes with the operatingenvironment temperature of no more than 110 ·c, for the turbodrills with floating stators- no more than 90·c,for the T02-C-type turbodrills-no more than 300 ·c.

Specifications of turbodrills, turbodrills-whipstock

T10

5K

T12

M3E

-172

3TSS

h1-1

72

TPS

-172

T12

M3B

-195

A75h

A7G

Tsh

T12

RT-

240

Diameter, mm 105 172 172 172 195 195 195 240

Length, mm 12700 7940 25400 26250 8060 17600 24950 8210

Weight, kg 590 1057 3530 3325 1440 3135 4425 2017

Number of stages in turbodrill 303 106 336 426 105 200 228 + hydro-braking grill 114

104

Operating fluid consumption, L/sec 8-12 25-28 20-25 25 45-50 30 30 50-55Shaft rotation speed, sec’,

revolutions per minute10,6-16,0(636-960)

10,5-11,7(630-702)

8,3-10,5(498-630)

7,3(438)

9,7-10,8(582-648)

8,7(522)

5,3(318)

11,6-12.7(696-762)

Pressure difference, MPa 4,5-10,2 2,85-3,5 5,7-8,8 6,5 2,9-3,6 7,85 6,9 4.4-5.4

Shaft torque, N•m 170-381 559-687 1128-1765 1746 714-882 1860 1814 2127-2550

Chisel diameter, mm 120,6-151,0

190,5-215,9

190,5-215,9

190,5-215,9

215,9-224,5

215,9 215,9 269,9

Connection threads:- to drill pipe

- to chisel3-883-76

3-1473-117

3-1213-117

3-1213-117

3-1473-117

3-1473-117

3-1473-117

3-1893-171

Max. drift angle, degree - - - - - - -


Specifications of turbodrills, turbodrills-whipstock

A6Sh

TO

2-17

2

3TSS

h1-1

95

3TSS

h1-1

95C

TO

2-19

5

ShO

1-19

5St

ando

ff sp

indl

e

A9G

TSh

3TSS

h1-2

40

A9Sh

TO

2-24

0

Diameter, mm 164 172 195 240 240 240 240

Length, mm 17250 9715 25700 10110 4800 23290 23225 16690 10170

Weight, kg 2095 1363 4790 1774 875 6125 5975 4605 2506

Number of stages in turbodrill 212 106 330 450 105 - 210 +hydro-braking grill 99

315 220 93

Operating fluid consumption, L/sec 20-25 25-28 30-35 28-35 30 - 45 32-34 45 45Shaft rotation speed, sec’,

revolutions per minute7,8 - 9,8(468-588)

10,4-11,7(624-702)

6,4-7,5(384-450)

6,5-7,3(390-440)

8,7(522)

--

4,1(246)

7,4-7,8(444-468)

7,0(420)

7,0(420)

Pressure difference, MPa 4,3-6,6 2,9-3,9 3,9-5,3 5,4-7,1 3,5 - 5,5 5,5-6,2 6,9 2,9

Shaft torque, N•m 680-1079 637 - 785 1481-2009 1973-2577 853 - 3060 2648-2991 3040 1343

Chisel diameter, mm 190,5 215,9-244,5 269,9-93,7

Connection threads:- to drill pipe

- to chisel3-1213-117

3-1213-117

3-117 3-1713-152

Max. drift angle, degree - 2 - - 2 2 - - 2


Drills specifications.

Drills are designed to drill wells of large holes with the operating environment temperatureof no more than 110 °C

Drills specifications

Code

Turb

odri

ll ty

pe

Num

ber

of tu

rbod

rills

Dri

ller

diam

eter

, mm

, no

mor

e th

an

Chi

sel d

iam

eter

, mm

Dri

lling

age

nt c

onsu

mpt

ion,

m

³/se

c, n

o m

ore

than

Dri

ll le

ngth

, mm

, no

mor

e th

an

Dri

ll w

idth

, mm

, no

mor

e th

an

Wei

ght,

kg,

no

mor

e th

an

Axia

l loa

d to

pit

, kN

, no

mor

e th

an

RTB 394M T12M3E-172 or 3TSSh1-172 2 394 190 0,056 12860 382 8200 80

RTB 490M T12M3B-195 or 3TSSh1-195 2 490 215,9 0,06 12860 474 10200 60

RTB 590M T12M3B-195 or 3TSSh1-195 2 590 269,9 0,06 12860 525 14400 85

RTB 760M T12RT-240 2 760 346 0,09 12000 730 12000 70

RTB 920M T12RT-240 2 920 445 0,09 12000 850 13000 75

RTB 1020M T12RT-240 2 1020 490 0,09 12000 950 13200 80

RTB 1260M T12RT-240 3 1260 445 0,135 12000 1180 21500 125

RTB 1560 T12RT-240 3 1560 490 0,135 12000 1450 22000 130

RTB 22M (2080) T12RT-240 4 2080 490 0,135 12000 1500 32400 190

RTB 2600 T12RT-240 4 260027302860

490620750

0,135 12000 2450 38340 225


SPARE PARTS


Slip 60 mm APR2-VBM 01.01.003-01

Slip 73 mm APR2-VBM 01.01.003-02

Hanger 60 mm APR2-VBM 01.01.000.02 SB

Hanger 73 mm APR2-VBM01.01.000 SB

Hanger 89 mm APR2-VBM 01.01.000.01 SB

Wedge housing 60, 73 mm APR2-VB M 01. 01. 001

Worm-wheel APR2-VBM 01.01.002

Worm-shaft APR2-VBM 05.000 SB

Automatic device body APR2-00.001M

Forks 60 * APR2-VBM 01.03.000 SB

Forks 73 * APR2-14.000

Forks 89 * APR2-14.000-01

Half-coupling APR2-14.000-02

Bail * APR-00.019

Flange APR-01.01.010

Centralizer insert 60 APR2-00.00.5M-1

Centralizer insert 73 APR2-00.010-01

Centralizer insert 89 APR2-00.010-02

Hanger support APR2-00.010-03

Electric drive APR2-01.010 SB

Flange 2PEI-VB.001

Cover 2PEI-VB.009

Bracket 2PEI-VB.003

Shoe PEI-VBM.00.00.001

* = on request

SPARE PARTS FOR TONGS

SPARE PARTS FOR TONGS KMU-50M

Wedge block 60 mm KMU-50.02.02.000-01 SB

Wedge block 73 mm KMU-50.02.02.000-02 SB

Wedge block 89 mm KMU-50.02.03.001

Gear-shaft 011 * KMU-50.01.00.011

Split wheel KMU-50.01.00.013

Bush 014 KMU-50.01.00.014

Gear wheel KMU-50.01.00.016 M

Pinion KMU-01.00.033

Planet carrier * KMU-50.01.02.000

Complete rotary head body KMU-50.01.01.000 M SB

Cover KMU-50.01.06.000M SB

Lever KMU-50.01.05.000 M SB

Shaft KMU-50.01.00.003M

Pusher KMU-50.01.00.003M

Wedge housing 48-73 KMU-50.02.02.001

Spider body KMU-50.02.01.000 SB

Spider (with wedges of all dimension-type) KMU-50.02.00.000 SB

Rotary head KMU-GP (with drive) * KMU-50.01.000

Rotary head KMU-GP (without drive) * KMU-50.01.000

SPARE PARTS FOR OIL FIELD EQUIPMENTSPARE PARTS FOR ELEVATORS ETA

Grips ETA-50 P 60 mm 5 ETA 010P-04 SB

Grips ETA-50 P 73 mm 5 ETA 010P-02 SB

Grips ETA-50 P 89 mm 5 ETA 010P SB

Grips ETA-50 for tubing strings of 60 mm 5 ETA 010A-04 SB

Grips ETA-50 for tubing strings of 73 mm 5 ETA 010A-02 SB

Grips ETA-50 for tubing strings of 89 mm 5 ETA 010A SB

Grips ETA-60 P

Set-in eye ring for ETA-SOP SV-10 ETA


SPARE PARTS FOR SWIVELS

Swivel washpipe VE-50

Maintenance and repair kit for VE-60

Maintenance and repair kit for VE-50

Maintenance and repair kit for VP-60

Maintenance and repair kit for VP-80

Maintenance and repair kit for VB-80

Swivel washpipe VB-80 01.001

Gian block VB-80 02.000 SB

SPARE PARTS FOR ROTARY TABLE UNITS

Drive shaft RU 01.000

Drive shaft RU 01.005

Gear wheel 5 ET A 010P-04 SB

Gear wheel 5 ET A 010P-02 SB

OTHER SPARE PARTS

Slip PKR 73, 89 RU 01.000

Slip PKR 114, 127 RU 01.005

Slip PKR 140, 146 5 ET A 010P-04 SB

Grips ETAD-80 - 73, 89, 102, 114 mm 5 ET A 010P-02 SB


SPARE PARTS FOR TONGS PBK-4

Complete gear-box

(right, left) PBK4-01.01.000 SB

Gear-wheel PBK4-01.01.003

Roller d=218 KPM-01.01.006

Gear-wheel block PBK4-01.01.007


Fly-wheel PBK4-01.01.040

Roller PBK4-01.01.013


Control panel * PBK-26-02-80-83

Hoisting cylinder PBK-4.02.00.000 SB

Cylinder PBK4-02.00.001

Roller hold-down cylinder PBK4-01.04.000SB

SPARE PARTS FOR WRENCHES KTsN

Chains KsN-1 TSZ-1 KTsN1-6 SB

Chains KTsN-2 TSZ-2 KTsN2-6 SB

Chains KTsN-3 TsZ-3 KTsN3-6 SB

SPARE PARTS FOR WRENCHES KTGU

Anvils for wrenches KTGU 60 mm KTGU-M-60-9



Maintenance and repair kit for KTGU-73

SPARE PARTS FOR WRENCHES KT

Slip KT.001

Anvils KT.002

Pin KT.003

SPARE PARTS FOR PACKERS (PVM on request)

Packer mandrel 3PVM 122x50 3PVM.001

Slip socket

3PVM 122x50 PVM.002 PVM.002

Slip 3PVM 118-50,

122-50 (136-50, 140-50) 4PMT.013 (3PVM.014)

Documents

RIGS FOR WELL DEVELOPMENT REPAIRimzgroup.co.uk/wp-content/uploads/2016/05/IMZ-Oil-Gas...RIGS FOR WELL DEVELOPMENT & REPAIR MOBILE DRILLING RIGS A 60/80 Rig A60/80 is designed to repair