Upload
reznoclad-hpl
View
18
Download
0
Embed Size (px)
Citation preview
exterior hpl
RG
O G
REE
N !
!N
EW E
DG
E H
PL
FAC
AD
Ew
ww
.exteriorh
pl.co
mexterior hpl
RAuthorised Dealer
100 % UV Protected
ABOUT REZNOCLADReznoclad is self-supporting high pressure laminate (HPL) with a decorative surface that is suitable for exteriors. It is fade resistant weather-proof and complies with standard EN 438.
It is entirely made up of layers of phenolic resin & impregnated craft papers with top decorative layer and UV protective film.
The manufacturing process involves the combining of papers with oapplications of high heat (150 c) and high pressure (9 Mpa) in which
resin polycondensation takes place. One or both sides can be decorative mixed with the phenolic resins.
exterior hpl
R
01
TYPES OF EXTERIOR PANELSREZNOCLAD panels are available in the following grades for their
suitability as per the required applications.
• Exterior Cladding Panels (Fire Retardant)
• Exterior Cladding Panels
• Exterior Cladding Panels (With Anti-graffiti)
• Wall and facade linings • Cladding or exhibition building
• Sporting and entertainment complexes
• Decoration of commercial sites • Residential dwellings
• silhouette profiles • fences • Facade Claddings
• Balcony Claddings • Partitions • Rear ventilated facades
• Ceilings • Outdoor furniture • Public facilities
• Playground facilities • Sport facilities • Sun protection
• Business entry portals • Functional constructions
• Attic Cladding • Awnings
REZNOCLAD panels are extremely durable with
international styling and a wide range of colours
available on both horizontal and vertical designs. Its
excellent technical properties make it suitable for the
building industries as an ideal alternative to traditional
materials.
APPLICATION
exterior hpl
R
02
CHARACTERISTICS
CLEANING & MAINTENANCE
HANDLING & STORAGESReznoclad panel comes with a film on top layer for protection during transportation. During
stocking, panels must be stacked horizontally on flat, stable shelfs, the panels to be stored in
closed rooms under dry, normal climatic conditions. Cover plates must always be left on the stack.
The cover should be weighted down. Any form of dirt or dust between the panels must definitely
be avoided. Panels must be lifted and not pushed or pulled over the edge when carrying or
loading.
For climate differences, keep panels waiting for 24 hours in new climate conditions. With pre-
installed fastering elements, care is to be take that the climatic effect is uniform on all sides. Use
intermediate layers of wood or plastic.
REGULAR SIZES
The protective film applied at factory must
be removed from the surface of the panel
immediately after installation to the facade.
The surface of reznoclad panels repels dust,
however over the time it may be necessary
to clean their surface with soapy water for
better aesthetic over time.
WARRANTIESThanks to practical experience over many
year and the high quality of Reznoclad HPL
Panels, warranties are available both for
the product range in general and for
specific projects. More information can be
obtained from your local representative.
3050*1300*6mm2440*1220*6mm
Thickness
On demand: 4 to 20mm
Grain direction
Easy to Clean
Moisture Resistance
StrikeResistance
Chemical Effects Resistance
AbrassionResistance
High Heat & Fire Resistance
Ÿ
Ÿ Resistance to atmospheric conditions
Ÿ Resistance to swelling in boiling water
Ÿ Fire-resistance
Ÿ Physical resistance to strikes and abrasion
Ÿ Chemical resistance to mild acids, rain, air
pollution
Ÿ Wide range of colors and patterns
Ÿ Easy to care and repair
Ÿ Do not contain any harmful substances
Resistance to UV rays
Ÿ
Ÿ Overall lightweight substructure and facade
Ÿ dimensional stability and flatness
Ÿ Light weight facade system
Ÿ Easier perforation
Maximum light fasten
exterior hpl
R
03
EXTERIOR CLADDING
FIXING METHOD
The lap Sliding Fixing Method has the advantage of being a very
attractive system of panel fixing. With pre-fabricated REZNOCLAD
Exterior Cladding panels for the lap sidings. It is easy to design
robust and modern facades. Besides the regular advantages of
REZNOCLAD Exterior Cladding panels, This lap siding panels looks
more eye catching.
MOUNTING INSTRUCTIONS
1. Preparing The Substructure
REZNOCLAD lap siding panels are installed using mounting clips fixed to a sub-structure of vertical wooden slats. Each slat must be at least 50 mm wide where two panels join to allow enough space for two mounting clips side by side. The gap between each slat should not exceed 500 mm as applicable to low building of up to 8m height. The panels are installed starting from the bottom. First of all, fit a horizontal base bar. Now fit the first row of mounting clips so they rest on the bar. Make sure you fit 2 mounting clips at each vertical joint between panels.
2. Installing the first row of panels
Place the groove along the lower edge of the REZNOCLAD lop siding panels onto the mounting clips. Secure the panels in place by fixing mounting clips along the lop edge of each panel. The panel above overlaps the first row of panels by approximately 25 mm. Fit a screw next to the lop middle mounting clip on each panel. This is designed to stop the sideways shifting of panels
3. Vertical joints
A slot for Fixing the mounting clips must be located at each vertical joint. Two mounting clips, one either side of the joint, ore needed to provide the necessary hold. Please use proper backing strips to seal the vertical Joint between cladding panels. If the siding elements ore arranged so the vertical Joints ore offset then it is sufficient to install the panel plus backing strip using o single mounting clip. If the vertical joints are in a line then two mounting clips need to be used. There must be a gap of at least 8 mm between the panels at the joint.
4. Outside corners/Inside corners with mitre
REZNOCLAD lap siding panels can be mitred lor both outside and inside corners. Outside corners: The lap edge of the panel must be 12 mm shorter than the lower edge of the poneI (regardless of the panel width). Inside corners: The lower edge of the panel must be 12 mm shorter than the top edge of the panel (regardless of the panel width). The mitred edges must hove a chamfer. Thesub-struclure needs to be protected with a plastic sheet to prevent water entering. Elements can be installed on both outside and inside corners using a variety of shapes of corner profile. In this case the panels ore cut to size without a mitre. Please make sure there is a gap of at least 5 mm between each panel and the corner profile.
5. Installing the top row of panels
Secure the top row of panels by fitting screws along the top edge of each panels. Use screws with painted heads to match the color of the panels, as used for the installation of full-sized Samrat exterior Cladding panels.
exterior hpl
R
04
ENVIRONMENTReznoclad is committed to continuous improvement of
environmental performances. These panels are not hazardous
to health and does not pollute the environment. It is made up
of 70% cellulose fibers and 30% thermosetting resins and does
not contain asbestos or heavy metals. These panels does not
emit gases, fumes, solvents or liquid substances.
Fixing Details Installation System
RIVET FIXING SYSTEM
exterior hpl
R
05
Woody Streaks 9363 Canyon Monument Oak 9391
American Elm 9354Light Knotty Pine 9322
Princess WalnutArizona Walnuts 9334 9383
Grey Monument OakWisconsin Walnut 9345 9394
exterior hpl
R
06
9351Brunt Wood9320Mustard Aquatone
9395Straight Wenge9394Oxford Cherry
9381Bengali Mango Dark 9384Versailles Walnut
9807Travetine Marble9806Gold Spray
exterior hpl
R
07
9422White
9420Frosty White 9421Smoke Grey
9425Black
9423Slate
9424Coffee
exterior hpl
R
08
REZNOCLAD PROJECTS
TECHNICAL SPECIFICATION
S. No. PROPERTIES
TEST METHOD
ATTRIBUTES OF PERFORMANCE
UNITS OF MEASUREMENT
RESULTS (AS PER EN438-6)
1. Surface Quality
1.1 Surface Quality EN 438-2.4 Spots, dirt and similar surface 2 2mm /m 2
202 2mm /mFibres, hairs & scratches
Dimensional Properties
Thickness
Size
Straightness of edge
Squareness
Flatness
EN 438-2.5
EN 438-2.6
EN 438-2.7
EN 438-2.8
EN 438-2.9
2.
2.1
2.2
Thickness Tolerance
Length and Width
Straightness of edges
Squareness
Flatness (measured on full-size sheet)
mm
mm
mm/m
mm/m
mm/m
5 T 8:+ 0, 4
+10/-0
1,5
1,5
6.0 T 10,0:5
Physical Properties 3.
3.1
3.2
3.3
3.4
3.5
3.6
3.7
4.
4.1
4.2
5.
5.1
EN ISO 1 78
EN ISO 1 78
EN ISO 527-2
EN ISO 1183
EN 438-2.21
EN 438-2.15
EN 438-2.17
EN 438-2.19
EN 438-2.29
EN 135 01
Stress
Stress
Stress
Density
Indent dia. 10mm 2 T < 6mm
Drop Height
Indent dia. 10mm T 6mm -
Drop Height
Mass increase - 2 T < 5mm
Mass increase - T 5mm
Appearance
Cumulative dimensional
change -2 T 5mm
Cumulative dimensional
change -T 5mm
Thermal Shock Resistance-
Appearance
Contrast
Appearance
Test as per EN 13823 (SBI Test) and EN ISO 11925 - 2 (Small-burner Test)
Classification - 3 T < 6mm
Classification - 6 T < 13mm
Mpa
Mpa
Mpa3gm/cm
min.
min.
max.%
max.%
Rating
Longitudinal %
Transversal %
Longitudinal %
Transversal %
Rating
Grey Scale Rating
Rating
Classification
Classification
9000
80
60
1,35
1400
1800
EGS- 7, EGF- 10
EGS- 7, EGF- 10
4
0.40
0.80
0.30
0.60
4
3
4
B-s2, d0
B-s1, d0
Flexual Modulus
Flexual Strength
Tensile Strength
Density
Resistance to impact with
large diameter bill
Resistance to Wet
Conditions
Dimensional Stability at
elevated temperatures
Weather Resistance Requirements
Resistance to Climatic
Shock
Resistance to Artificial
Weathering
Fire Performances
Fire Reaction Classification
PERMEABILITY WATER PROTECTION
THERMAL INSULATION (ELEMENATION OF
HEAT BRIDGE)
SOLAR PROTECTION
ACOUSTICPROTECTION
BREATHABLE FACADE FOR HEALTHIER BUILDINGS- REZNOCLAD HPL IS HIGHLY SUITED FOR VENTILATED FACADE SYSTEMS.
exterior hpl
R
09
exterior hpl
R
10
exterior hpl
R
11