Quick Guide XCAL-Harmony v2 - accuver-emea.com · * : Deletes the selected call scenario. 2) Created AutoCall scenarios are listed and managed by call types. * Tapping a call type

Quick Guide

XCAL-Harmony v2 2015 Dec

Contents

1. Installation of XCAL-Harmony v2

2. Syncing XCAL-Harmony and XCAL-Mobile/Solo

3. Main Menu

3-1. Configuration

3-2. Monitoring

3-3. Inbuilding

3-4. Map

3-5. Scanner

3-6. Logdata

3-7. Settings

3

1. Connect PC and Tablet by using cable. 2. In PC, create a new folder in tablet, and add XCAL-Harmony (*.apk) file in it.

3. In tablet, run ES file explorer. (ES File Explorer can be downloaded from Play Store.)

4. Execute XCAL-Harmony (*.apk) file. 5. When installation is successfully completed, XCAL-Harmony icon appears in application menu.

6. Run XCAL-Harmony application, and main screen appears as above.

1. Installation of XCAL-Harmony v2

4

1. Run XCAL-Mobile. 2. Select [M/S] from HW Menu.

3. Tap to select [Messenger (Harmony v2)].

4. Messenger Mode is activated and started.


5

5. [Bluetooth Search]: Allows

Bluetooth search at the initial

connection with XCAL-Harmony.

Tap [Yes] to allow.

From the second-time connection

to XCAL-Harmony, no need of

allow BT search.


6

Main screen of XCAL-Harmony v2 appearing when executing XCAL-Harmony application.

3. Main Menu

7

1. Menu bar at the top of main screen is displayed in all screens of XCAL-Harmony always moving to other menus directly by clicking desired menu buttons.

2. Swipe screen left and right to change menus.

Menu selection by swiping left and right and clicking menu buttons.

3. Main Menu

8

1. Syncing XCAL-Mobile/Solo – XCAL-Harmony syncs to XCAL-Mobile/Solo via Bluetooth.

1) When there is no searched paired devices in Bluetooth search list.

1) Tap a port number to connect XCAL-Solo/Mobile.

1

2

2) Tap [Scan] button when there is no mobile to connect in Paired Device List.

3-1. Configuration

9

4) When no device is searched in Bluetooth scan list, check if Bluetooth search permission is configured to On in XCAL-Mobile/Solo application.

4

3

In XCAL-Mobile/Solo application, make sure XCAL-Mobile/Solo information.

3-1. Configuration

1. (Cont’d) Syncing XCAL-Mobile/Solo – XCAL-Harmony syncs to XCAL-Mobile/Solo via Bluetooth.

1) When there is no searched paired devices in Bluetooth search list.

10

1) Tap a port number to connect XCAL-Solo/Mobile.

1

2) Paired Devices list 에 원하는 모바일이 없는 경우 “ ” 을 선택합니다.

2

2) XCAL-Mobile/Solo, which have ever been connected to XCAL-Harmony before, are listed up.

Port number of the latest AutoCall is displayed.

* If XCAL-Mobile/Solo is connected to the lastly connected port of XCAL-Harmony, the lately tested AutoCall scenario is assigned automatically.

3-1. Configuration


2) When there exists searched paired devices in Bluetooth search list.

11

5) Selected XCAL-Mobile/Solo is connected to port 1 as configured successfully.

* Configure the other ports to sync XCAL-Mobile/Solo via Bluetooth.

5

3-1. Configuration


3) Syncing XCAL-Mobile/Solo via Bluetooth.

12

3-1. Configuration


3) Syncing XCAL-Mobile/Solo via Bluetooth for all XCAL-Harmony ports.

13

Tap

Tap port# to disconnect XCAL-Mobile/Solo, and tap [OK] button to confirm.

3-1. Configuration


4) Disconnecting the synced XCAL-Mobile/Solo from XCAL-Harmony.

14

1 1) Tap [NEW], [EDIT], and [DEL] icons to create, edit, and delete call scenarios. * : Creates a new call scenario. * : Edits existing call scenarios. * : Deletes the selected call scenario.

2) Created AutoCall scenarios are listed and managed by call types. * Tapping a call type and corresponding call scenarios are listed. * If there is no created call scenario, call type button is shown in gray. * If there exists created call scenarios, call type button is shown in green.

3) Detailed information of selected call scenario is displayed. * I : Idle time/ S : Setup time/ T.S : Traffic.Setup time/ T : Traffic time

2

3

3-1. Configuration

2. AutoCall Scenario - In main Configuration menu screen.

15

3-1. Configuration

2. AutoCall Scenario – Scenario Setup screen.

[Scenario Setup] screen creates, edits, and deletes call scenarios. [Scenario Setup] screen appears when tapping [NEW] button.

16

4) Tap to select a call scenario of each call type.

4

5 Tap

5) Tap a scenario assignment button of a port# to assign a call scenario.

3-1. Configuration

2. AutoCall Scenario

By tapping each scenario assignment button for respective ports, call scenarios are assigned.

17

3-1. Configuration

2. AutoCall Scenario

By tapping each scenario assignment button for respective ports, call scenarios are assigned.

18

3-2. Monitoring

1. Call Status – Monitoring status of mobile and AutoCall test

19

DM 상태 색상 표시 : Connected : Disconnected : Connecting

* Mobile number + MIN Number_Current network * Background color shows status of current network

of mobile.

- Idle/Setup/T.setup/Traffic + Progress - Progress = (Current Time/Time configured in scenario) * 100 -If Total Time is set, remained total time is displayed. * Progress colors for each time section : Idle : Setup/T.setup : Traffic

*Total = number of calls / number of call scenarios *Success = number of success call (Success count/total call)*100 *Fail = number of all calls excepting success calls (BQ+CBQ+Connection+Setup+Traffic+Timeout+Drop+Incomplete+Pending)

* Status of DM Port : Connected : Disconnected : Connecting

* Status of GPS : Lock : Unlock : Disable

: LTE : WCDMA : GSM : CDMA : TD-SCDMA : Wi-Fi : Unknown

1. Call Status

3-2. Monitoring

20

Tap

1) Tap a call status section, Detail View screen appears (see next page).

1

1. Call Status

1) Detail View

3-2. Monitoring

21

2

Turn On/Off Wi-Fi of corresponding mobile.

Search call results by filtering scenario name or call result type.

1. Call Status

1) (Cont’d) Detail View

3-2. Monitoring

22

Tap

1

1) Tap filter setting buttons.

2. RF Summary

1) Filter Setting

3-2. Monitoring

23

2 2) Select a network to monitor. * If [Current] is configured, RF parameter is displayed according to current network of mobile.

3

3) RF parameter can be monitored after filtered.

2. RF Summary

1) (Cont’d) Filter Setting

3-2. Monitoring

24

3. Signal Graph

1) Setting

3-2. Monitoring

25

Tap

1

1) Tap G1 or G2 button of parameter.

3. Signal Graph

1) Setting

3-2. Monitoring

26

4. Cell Measurement

: Monitors cell measurement result of connected XCAL-Mobile/Solo.

3-2. Monitoring

27

5. Signaling MSG

: Displays Signaling Message + SIP Message + Call Event

3-2. Monitoring

28

5. Signaling MSG

1) Signaling Message Filter Setting – appearing by tapping [Filter] button

3-2. Monitoring

29

Tap

1

6. User Defined

: Organizes screen by selecting menus of Call Status, RF Summary, Signal Graph, Cell Measurement, Signal MSG of M1 ~ M6.

3-2. Monitoring

30

2

Select M1 ~ M6 to be displayed in the first Screen.

Select a monitoring menus of Call Status, RF Summary, Signal Graph, Cell Measurement, Signaling MSG to be displayed in the first screen.

6. User Defined

1) User Defined Settings

3-2. Monitoring

31

Lists up test building information. Building information is saved and re-used for next in-building tests. *.ibwc file can be imported. See next pages.

Configures in-building information.

Configures in-building floor information.

Starts in-building test.

3-3. Inbuilding

1. Setting

32

[GET GPS] button: Configures building location information automatically taking Google Address data.

Enter a building name.

Enter building address manually if GET GPS button does not work.

Configure building floor to conduct test. Floor setting screen pops up. See next page.

Saves or deletes building information.

Configures test type in Measure pop-up screen; Moving, Fixed, TAB+JPG, Real Time Mapping.

- Moving: Performs call test while moving in floor image. - Fixed: Performs call test at a certain measurement point inside a building. - TAB+JPG: Performs call test applying *.jpg or *.tab file as floor image. Call test is conducted while

moving in floor image. - Real Time Map: Performs call test applying Google map as floor image. Call test is conducted while

moving in floor image.

1. Setting

1) Building Setting

3-3. Inbuilding

33

a. Tap [Add] button, and [Add Floor] screen pops up. b. Configures Floor name. c. Tap [Select Image] button to select floor image

from Camera/Gallery/Photos. d. Saved floor information can be edited or deleted by

using [Edit] and [Delete] button.

3-3. Inbuilding

1. Setting

2) Floor Setting

34

1) Tap [Go to the image Map] button to start in-building test. Measure screen pops up. See the next pages.

3-3. Inbuilding

2. Measurement – Test Type Setting

1) Moving Point Test (1): Performs call test while moving in floor image. Test engineer marks test points during test.

35

2) Tap [Floor List] button. 3) Select a floor to test. Floor names configured from Floor Setting are listed up.


1) Moving Point Test (2)

3-3. Inbuilding

36

When floor name is selected, floor image is sent to mobile. Icons of Mobile# are turned from red to green color. Only when all mobile# icons are in green color, in-building test is able to be started.

Floor image can be zoomed in and out.

Selected floor image is displayed in in-building test screen.



3-3. Inbuilding

RF Parameter can be configured.

37



3-3. Inbuilding

38

4-1) Tap P1 point in floor image. 4-2) Add Point] screen pops up. 4-3) Tap [Add] button to confirm.

5) Every time a test engineer marks test point, [Add Point] screen pops up to confirm location once again.

6) After P1 point is marked in floor image, tap [Start] button to start in-building AutoCall test. AutoCall setting should be completed prior to configure in-building test.



3-3. Inbuilding

39

7) When the test engineer arrives at the next point (P2), tap floor image to mark P2. Then, repeat to move to the next points.

8) When the test engineer completes the latest point, tap [Done] button to stop in-building test.



3-3. Inbuilding

40

9) AutoCall Stop screen pops up. Tap [OK] button to confirm.



3-3. Inbuilding

41

1) Select [TAB+JPG] for Measure type. Names of tab and jpg must be identical.

Floor Setting can be skipped for TAB+JPG type test.


2) TAB + JPG Test (1): Performs call test applying *.jpg or *.tab files as floor image. Call test is conducted while moving in floor image.

3-3. Inbuilding

42

3) Select a floor to test. Floor names configured from Floor Setting are listed up.


2) TAB + JPG Test (2)

3-3. Inbuilding

2) Tap [Floor List] button.

43

4) Tap a start point.

No floor list exists for TAB+JPG type test. 5) Tap [Start] button to start test.

3) When *.tab and *.jpg files are successfully loaded, floor image is shown in in-building test screen properly.



3-3. Inbuilding

44

6) Tap the latest point.

7) Tap [Done] button to complete test.



3-3. Inbuilding

45

1) Select [Real Time Mapping] for Measure type.

Floor Setting can be skipped for Real Time Mapping type test.


3) Real Time Map Test (1): Performs call test applying Google map as floor image. Call test is conducted while moving in floor image.

3-3. Inbuilding

46

3) Select a floor to test. Floor names configured from Floor Setting are listed up.


3) Real Time Map Test (2)

3-3. Inbuilding

2) Tap [Floor List] button.

47

4) Tap a start point.

No floor list exists for Real Time Mapping type test.

5) Tap [Start] button to start test.



3-3. Inbuilding

48

6) Tap the latest point. 7) Tap [Done] button to complete test.



3-3. Inbuilding

49

*.ibwc file of iBwave can be applied for Building information. Imported ibwc files are listed in Building list adding the index of [iBwave Data].

3. Use of iBwave (ibwc) file for Building Information

1) Importing iBwave (ibwc) file (1)

3-3. Inbuilding

50

iBwave사의 ibwc 파일을 선택합니다. iBwave사의 ibwc 파일을 선택합니다. ibwc load가 성공하면 Building Name 옆에 iBwave Data로 표시되면서 List에 등록됩니다.

Floor information is configured automatically by using floor information of ibwc file.

3-3. Inbuilding

3. Use of iBwave (ibwc) file for Building Information

1) Importing iBwave (ibwc) file (2)

51

Take GPS data of XCAL-Harmony tablet. Move current location at the center.

Monitors RF value by using the selected mobile’s GPS data.

Tap

Configure MAP settings.

Show/Hide mobile call status at the bottom.

3-4. Map

1. Map (Normal)

: Monitors test route, location of selected RF parameter, and etc by using different colors.

52

3-4. Map

1. Map (Satellite)

: Monitors test route, location of selected RF parameter, and etc by using different colors.

53

Assign identical RF items for all mobile.

* Configure RF item for each mobile. * Set All Settings OFF.

Configure colors of RF item ranges.

3-4. Map

1. Map

1) Map Setting – appearing when tapping [Settings] button in map.

54

[Call Event] : Turns On/OFF events to be displayed in map.

[Drive Route] : Supports drive route file in *.kml format. • Drive Route Update Local: Selects files saved in local folders of XCAL-Harmony tablet. • Drive Route Update FTP: Downloads files from FTP server. • Drive Route Clear: Cancels configured driver route.

3-4. Map

1. Map

1) (Cont’d) Map Setting – appearing when tapping [Settings] button in map.

55

Syncs IBFlex Scanner to XCAL-Harmony via Bluetooth.

Configures Scanner options.

Displays scan result.

Displays summarized scan result.

Configures frequency setting automatically. Menu for beginner users.

Displays status of logging and GPS.

3-5. IBFlex Scanner

1. GUI – Main Menu buttons

56

1) Tap [Detect Device] button to search Bluetooth scanner.

2) When scanner is searched, [Detection Process Completed.] is displayed.

3) When scanner is not searched, reboot scanner or tap [Detect Device] button to retry.

3-5. IBFlex Scanner

2. H/W Setting menu

1) Scanner Control – Connecting Scanner (1)

57

4) Tap [Connect Device] button to sync scanner.

5) Select a scanner to sync.

2. H/W Setting menu


3-5. IBFlex Scanner

58

6) If scanner is synced successfully, [Control Result Code = 0 = Success] is displayed.

2. H/W Setting menu


3-5. IBFlex Scanner

59

2) If scanner GPS is successfully synced, color of GPS Connection button is changed.

• Longitude/Latitude data is displayed. • [Get Location] button: Moves to the current location in map.

1) Tap [Connect GPS] to sync GPS of scanner.

2. H/W Setting menu

2) Scanner Control – Connecting Scanner GPS

3-5. IBFlex Scanner

60

[Device Info] button: Displays detailed information of scanner. Version information of scanner is displayed.

2. H/W Setting menu

3) Scanner Control – Scanner Device Info

3-5. IBFlex Scanner

61

7 scan types are supported. Up to 15 scan ID can be registered and managed for each scan type. Scan ID 1~15 - LTE Enhanced Top N Signal, Scan ID 21~35 - WCDMA Top N Pilot Scan ID 61~75 - CDMA Top N Pilot Scan ID 81~95 - EVDO Top N Pilot Scan ID 41~56 - GSM Color Code Scan ID 111~125 - RSSI Scan Scan ID 161~175 - Blind Scan

1) Tap [Scan Setting] menu.

3. Scan Setting menu (1)

3-5. IBFlex Scanner

62

1) Tap [LTE Enhanced TopN Signal] type.

2) Setting screen pops up. Configure scanning options. • Scan ID • Scan Mode • Protocol Type: Special option for LTE Enhanced

TopN Signal type only. • Band Code • Channel Number • Channel Stype It is recommended not to configure Advanced Setting as On for beginner users.

3) Tap [Save] button to save.

4) When configuration is properly saved, [Unregistered] button is turned to [Registered].


3-5. IBFlex Scanner

63

5) According to the scanner configuration, Scan ID, Scan Type, Band Code, Channel Number, Channel Style are displayed.


3-5. IBFlex Scanner

64

[Scan] button: Starts scanning of the selected Scan ID. [Delete] button: Deletes the selected Scan ID.

[Scan all IDs] button: Scans all Scan ID sequentially.

[Stop all] button: Stops all Scan ID in progress. [Delete all]: Deletes all saved Scan ID.

3. Scan Setting menu

1) Starting scanning (1)

3-5. IBFlex Scanner

65

[Activate]: The corresponding Scan ID is currently conducting scanning job.

3. Scan Setting menu

1) Starting scanning (2)

3-5. IBFlex Scanner

66

2) Selects a Scan ID which is currently conducting scanning job.

1) Tap [Scan View] menu.

4. Scan View

3-5. IBFlex Scanner

67

Lists up all Scan ID which are currently conducting scanning job. Scan ID with no Cell IP for Top1 in scanning result is turned to yellow color.

1) Tap [Total Summary] menu.

5. Total Summary

3-5. IBFlex Scanner

68

5. Total Summary (Example)

3-5. IBFlex Scanner

69

1) Tap [Easy Mode] menu.

2) Select when Channel Number of Band Code is not checked.

3 tech are supported for Easy Mode.

3) Select a Band Code to scan. [Start Blind Scan] button: Searches Channel Number taking 1 ~ 10 minutes.

6. Easy Mode (1)

3-5. IBFlex Scanner

70

4) Searched Channel number are listed up.

5) Tap [Add Channels] button to add to Scan ID automatically.

6. Easy Mode (2)

3-5. IBFlex Scanner

71

6) Configured Channel Number is displayed.

6. Easy Mode (3)

3-5. IBFlex Scanner

72

[Logging Start]: Saves scanning result in file.

Increased logging file size is monitored.

Logging file is saved in the folder of XCAL-Harmony-V2/Logging.

6. Easy Mode – Logging

3-5. IBFlex Scanner

73

1) Details of FTP Server configuration is displayed for uploading logdata.

* FTP configuration is saved to synced XCAL-Mobile/Solo.

2) Configure FTP server for uploading logdata.

1

2

3-6. Logdata

1. Logdata

1) FTP Server Setting

74

1

1) All logdata of selected date is uploaded at once.

3-6. Logdata

1. Logdata

2) All Logupload

75

2

• Select a test date, and corresponding logdata (*.drm) is listed up.

• Select a logdata from the list, and the call result history of the corresponding *.drm is displayed in the right section.

• List up call result history of corresponding logdata created in the configured test date.

3-6. Logdata

1. Logdata

2) Mobile# Logupload

76

3-7. Settings

1. Configuration

1) Save/Load All Settings: Saves current setting, and applies saved setting.

• ON: Configuration file is automatically popped up when executing XCAL-Harmony.

77

3-7. Settings

1. Configuration

1) Save/Load All Settings: [Save All Setting] button saves all connected mobile information and scenario information.

78

3-7. Settings

1. Configuration

1) Save/Load All Settings: When [Load All Settings] is started, mobile synchronization and scenario configuration are started

automatically.

79

3-7. Settings

1. Configuration

1) Save/Load All Settings: Existing setting file list (*.cfg) is automatically popped up and can be applied at the initial execution of

XCAL-Harmony.

80

3-7. Settings

2. Scenario

1) Export/Import Scenario: Imports/Exports AutoCall scenarios to/from FTP server.

81

• All Scenarios: Saves all logdata in one *.drm file. • Per file size: Saves logdata splitting in every configured file size. • Per time: Saves logdata creating every configured time. • Real Time Compress: Saves logdata compressing in real time. • Naming Log File (Before AutoCall): Enter log file name when starting

AutoCall test.

3-7. Settings

3. Logdata

1) Logging Option: Configures how to save logdata.

82

3-7. Settings

4. AutoCall

1) Automatic AutoCall Stop: Starts or Stops the whole AutoCall test process when XCAL-Mobile/Solo error is encountered.

• On: Terminates the whole AutoCall test process when the current AutoCall is stopped due to error of XCAL-Mobile/Solo.

• Off: Continues the remaining calls of AutoCall test even if the current AutoCall is stopped due to error of XCAL-Mobile/Solo.

83

3-7. Settings

5. Replay Mode

1) Replay Mode: Replicate past call test by replaying saved replay file.

84

3-7. Settings

5. Replay Mode

1) Replay Mode: Select a replay file and click [Start] button to replicate past test in time order.

85

• ON: Saves replay file. • Off: Does not save replay file.

3-7. Settings

5. Replay Mode

2) Make Replay File: Saves and replay AutoCall test conducted in XCAL-Harmony.

86

3-7. Settings

6. Help

5) About: Shows License status of XCAL-Mobile/Solo currently synced to XCAL-Harmony.

11 Floor, 190 Seohyen-Ro, Bundang-Gu, Seongnam-Si, Kyungki-Do

TEL : +82-31-788-1700 FAX : +82-31-705-1246

www.Accuver.com

Thank you

TEL:031-788-4600

TEL:031-788-4600

TEL:031-788-4600

Documents

Quick Guide XCAL-Harmony v2 - accuver-emea.com · * : Deletes the selected call scenario. 2) Created AutoCall scenarios are listed and managed by call types. * Tapping a call type