Product Training – WBTS + DMP330. DMP #201 DMP #202 DMP#203 DMP #204 PBX Phone #201 #202 #203 #204 WBTS N PSTN...... Existing PBX #301 #302 #303 #304

Product Training – WBTS + DMP330

DMP #201

DMP #202

DMP#203 DMP #204

PBX Phone

#201

#202

#203

#204

WBTS

N

PSTN.

.

.

Existing PBX

#301

#302

#303

#304

Internet

Hot Spot

Enterprise

DMP

DMP

GSM Network

Access Point

Broadband Modem

Plug WBTS to the SLT ports of

exiting PBX

WAN

L1L2L3

L4

WBTS + DMP330 Hardware Installation

WBTS Hardware Overview

Front view of WBTS


Back view of WBTS


Rear Panel of WBTS

Front Panel of WBTS

· -- WBTS ( Wireless Base Transceiver Station)

· 4 POTS Ports (L1 – L4) : · to be plugged into single line ports of any PBX/KTS

· WAN port :· to be plugged into the Ethernet port of ADSL/Cable modem

· LAN port (LAN1 – LAN3) :· to be plugged into the Ethernet port of PCs or network

devices

· PWR IN :· to be plugged into the power cord of power adaptor of

WBTS

Hardware Installation

Hardware Installation

Label Function

WAN RJ-45 connector: Connects the device to your cable modem, or to your ADSL Modem, It’s to connect to the remote network

LAN1-3 RJ-45 connector: Connects the device to your PC's Ethernet port, or to the uplink port on your LAN's hub,

Line 1-4 RJ-11 connector: Connects the device to your SLT lines of PBX

PWR IN Connects to the supplied power converter cable

On/Off Switches the device on and off

Hardware InstallationLED Name Color Status Description

PWR Green On Power on.

Off Power off.

WLAN Green On Wireless LAN initialization success.

Off Wireless LAN is not present.

LINE (1-4) Green Off PSTN Line is idle.

On PSTN Line is busy.

LAN (1-3) Green On LAN connected.

Off LAN network connection not present.

Flashing LAN activity present (traffic in either direction).

WAN Green On WAN connected.

Off WAN network connection not present.

Flashing WAN activity present (traffic in either direction).

WBTS + DMP330 Software Configuration

Software configuration Introduction

- Quick configuration( 快速安裝 ) -- Wizard

Restore to default value on WBTS, then it will enter the Wizard mdoe including the following settings.

-WAN Settings: It supports DHCP, Static IP and PPPoE.-LAN Settings: Here you can enable / disable DHCP server.-Wireless Basic: Here you can enable / disable wireless or changing SSID.-Wireless Security: Here you can enable / disable wireless security.-Internet Time: Here you can enable / disable Internet time and changing time zone.-Numbering Plan: Here you can define the numbering plan range.-Call Routing Table: Here you can set the call routing rule that allows the numbers you dialed will thru the correct interface (PSTN or IP trunk).

- Username / Password for Configuration Web page

Default Username / Password is ‘admin1234’ / ‘123456’ .

用網路線將 WBTS 和電腦連接 ,WBTS 插在 LAN Ports, 電腦設自動取得 IP, 打開 IE0 瀏覽器 ,網址處 Key in 192.168.1.1


輸入固定 IP 資料



設 AP 的名稱 , 若有設很多 AP 要漫遊 , 請所有 AP 的 SSID 要設一樣


看是否要設金鑰



設手機機號碼



撥碼設定



- Device Info

-Summary: Here you can see “Version Info.” and “Network info.”.

-Statistics: Here you can see “Network Statistics”.

-Route: Here you can see “Route Info.”.

-ARP: Here you can see “ARP Info.”.


- Device Info

- Summary : Here you can see “Version Info.” and “Network info.”.


- Device Info

- Statistics : Here you can see “Network Statistics”.


- Device Info

- Route : Here you can see “Route Info.”.


- Device Info

- ARP : Here you can see “ARP Info.”.


- Advanced-LAN: Here you can enable / disable DHCP server.


- Advanced

-WAN: It supports DHCP, Static IP and PPPoE.


- Advanced

-Dynamic DNS: It allows you to have a alias / URL name for dynamic IP address in any domain.


- Advanced

-Dynamic DNS: It allows you to have a alias / URL name for dynamic IP address in any domain.


- Wireless

-Basic: You can enable or disable the wireless LAN interface, hide the network from active scans, set the wireless network name (also known as SSID) and restrict the channel set based on country requirement.


- Wireless

-Security: You can set the network authorization method, select data encryption, specify whether a network key is required to authenticate to this wireless network and specify the encryption strength.


- Wireless

-Mac Filter: It allows users to Add/Remove hosts with the specified MAC addresses that are able or unable to access the wireless network.


- Wireless

-Wireless Bridge: It allows the users to configure wireless bridge features of the wireless LAN interface.


- Wireless

-Advanced: It allows you to configure advanced features of the wireless LAN interface.


- Wireless

-Station Info: Authenticated wireless stations and their status will be shown here.

Software configuration Introduction- Voice

-Phone:

-Phone Extension: The WBTS combines Proxy and Registrar servers in its application. The all phones registered to the internal Registrar are set here.


- Voice-Trunk:

-Answering Positions: It allows you to configure answering position for each PSTN Trunk line. You can choose Auto Attendant, or manually configure the target phone number on Day/night basis.

請選 AA


-Trunk

-Call Routing Table:


- Voice

-Trunk

-Call Routing Table: Every number you dialed from the phone of WBTS will try to match the call routing table, and choose the corresponding route to send the call.

So, here is the explanation of call routing table.

1. 'From' and 'To' means the preceding digits of the dialing number. For example, From = 0, To = 9 , that means First digit allows 0 - 9. Also, if you set From = 200, To = 300, that means First 3 digit allows 200 - 300. So, it depends what number you will dial.

2. If the number you dialed matched the 'From & To' range, then system will check the next item, Max and Min. - Min : Minimun digit , the table will be triggered by the Minimum digit , then will wait the number dialing till 'Max digit' or the inter- digit time out, and then sending the number.


- Voice

-Trunk

-Call Routing Table:

- Max: Maximum digit, the table will send the number when the number digit match the Max. digit.

3.'Del' : it means deleting the preceding number. For example, if Del =2, and you have dialed '123', then the system will delete '12', and just send '3'.

4.'Insert': it means insert the prefix number. For example, if Insert = 12345, and you have dialed '666', then system will send '12345666'.

5.'Destination': it means the call will go through the way / interface.


- Voice

-System

-Numbering Plan: It allows you to configure extension number range. You can also define some special service numbers in the table.


- Voice

-System

-Service Mode: It allows you to configure the day/night service mode. You can also customize the working time manually for each weekday. This service mode settings is for answering position.


-System

-Transmission: It allows you to configure some parameters regarding audio and FXO ports.


- Voice

-Voice Mail

-Advanced: It allows you to browse, upload or download voice files and settings via FTP.


- Management

-Settings: System Administrator can do the WBTS settings backup, restore, and restore to default here.


- Management



- Management



- Management

-Log: It allows System Administrator to view the System Log and configure the System Log options.


- Management

-Registered Phone: This page lists the information of registered phones.


- Management

-Time Settings

-Internet Time: It allows you to configure the NTP time server so the WBTS can synchronize its system time with NTP time server automatically.


- Management

-Time Settings

-Day light Save: It allows you to configure the Daylight Saving Time (DST) which supports auto adjustment for daylight saving time.

Software configuration Introduction- Management

-Access Control -IP Addresses: If enabled, WBTS will permit access to local management services from IP addresses contained in the Access Control list. If the Access Control mode is disabled, the system will not validate IP addresses form incoming packets.


-Access Control -Password: In this page you can define the passwords for administrator.


-Upgrade: It allows to update the firmware of WBTS. The new released software could be updated from the Local PC side or remotely. Click the “Browse” to locate the new software image file in the PC. Then, click “Upgrade” to process the software upgrade.


-Save&Reboot: Click “Save/Reboot” to reboot the WBTS. The WBTS would save the configuration before reboot, so that modified settings would take effect after reboot.


-Diagnostics: This page provide the following information to users. - The network connection information on the net. - The status of WBTS’s PSTN line


Logout:

The WBTS doesn’t allow two computers logon at the same time. So, users need to remember logout after finishing the settings. Or the WBTS system will be logout automatically after 3 minutes during no any web configuration operation.

Software configuration IntroductionDMP330 手機設定 :

- VoIP Settings: Press “ 主選單” “網路電話” “ SIP 設定” “模式設定” 選一模式 ( 如 : 模式三 ) “ 選項” “編輯” “帳戶設定” 將帳戶設定內所有的資料鍵完 ( 如後頁說明 ) 儲存

- Common Setting: 回到模式三 “編輯” “一般設定” “設定檔名稱” “ 編輯”改為分機號碼 “選項” 完成返回

Software configuration Introduction - Account Setting( 帳戶設定 ): “ 帳戶設定” , then key in the following items. - SIP 伺服器位址 : WAN 的話就是固定 IP IP address, 如果是 LAN 的話就是 192.168.1.1 - SIP 連接埠 : 5060 (By default value, 不用改 .) - 顯示名稱 : Enter the display you want. (Suggest to enter the user’s name and phone number.) ( 一般是設分機號碼 ) - 使用者名稱 : 設在 WBTS 上的分機號碼 - 密碼 : 設在 WBTS 上的分機號碼 ( 一般是設分機號碼與密碼相同 ) - 驗證名稱 : 設在 WBTS 上的分機號碼 ( 一般是設分機號碼 ) - After enter the account setting: Press “ 完成” Press “ 是” 儲存 Press “ 返回” to back to the previous page Press “ 啟動” 去啟動這個模式 .

Software configuration Introduction - Wireless Settings Press “ 主選單” “網路電話” “無線區域網路” “搜尋網路” 找到 WBTS” 選項” “連接” “返回”回到主畫面如果設定正確 , 可以在手機左上方看見 VOIP 的 icon

※ 到一個陌生環境找尋 AP 也是這樣找尋 , 如果沒有設金鑰 , 就可以很快登入 !!


- 每次手機開機自動登入 WBTS 設定方式

Press “ 主選單” “網路電話” “無線區域網路” “搜尋網路” 選擇你要的 AP, 如 WBTS) “ 選項” “定義存取點” , 依照下列資料設定完成即可 - 連線名稱 : keep the original value. - WLAN 網路名稱 : keep the original value. - 網路模式 : keep the original value. (Infrastructure) - 安全模式 : You can change it or keep the original value. It depends. - 加密方式 : You can change it or keep the original value. It depends. -WLAN 安全性設定 : 如果 AP 有金鑰 , 請在此處設定 - TCP/IP 設定 : keep the original value. - SIP 設定 : 選擇常要登錄於 WBTS 的模式完成 !!

回到”無線區域網路’ “存取點設定 ” 選擇剛設好的存取點 “選項” “連接”

Documents

Product Training – WBTS + DMP330. DMP #201 DMP #202 DMP#203 DMP #204 PBX Phone #201 #202 #203 #204 WBTS N PSTN...... Existing PBX #301 #302 #303 #304