PNMS Installation Manual WXP (S462961E)

8/13/2019 PNMS Installation Manual WXP (S462961E)

1/31

ROI-S04629-061E030716

P ASOLINK

N ETWORK

MANAGEMENT

S YSTEM

Install Manual

(WindowsXP)for version 4 23 XXX

NEC CorporationCopyright 200


2/31

ROI-S04629

- i -

Table of Contents

1. Order of Installation .........................................................................................................12. Phone and Modem Options Setting..................................................................................23. Dial-up Setting..................................................................................................................74. LAN Setting....................................................................................................................165. PNMS Setup....................................................................................................................196. Launching PNMS............................................................................................................227. NetConfigTool Setup .......................................................................................................23


3/31


4/31

ROI-S04629

- 2-

2. Phone and Modem Options Setting

(1) Click on Start | Settings | Control Panelon the Windows XP start tab.

(2) Click on Phone and Modem Optionsicon to start configuring the modem.


5/31

ROI-S04629

- 3-

(3) Select country and input area code on Location Information. Click on OK buttonto continue.

(4) Verify Location and Area Code.


6/31

ROI-S04629

- 4-

(5) Select Modem tab, click on Addbutton to continue adding the new modem.

(6) Check Dont detect my modembox and click on Nextbutton to continue.


7/31

ROI-S04629

- 5-

(7) Select Standard Modem Types and Standard 19200 Modem from Manufacturerand Models list respectively. Click on Nextbutton to continue.

(8) Select Selected ports and COM1, then click onNextbutton to continue. If you areusing multi-port configuration, select All ports to install the standard 19200 bpsmodem driver to all available COM ports.


8/31

ROI-S04629

- 6-

(9) Click on Finishbutton to finalize the new modem installation.

(10) Verify that COM1 Standard 19200 bps Modem is displayed on the list. Click onOK button.


9/31

ROI-S04629

- 7-

3. Dial-up Setting

(1) Click on Start | Settings | Control Panel | Network Connectionsicon to startconfiguring the Dialup setting.

(2) Network Connections is displayed. Click theCreate a new connection in NetworkTasks category. Dial-up setting is written in this Section 3. If you connect PNMSto equipment with LAN connection, please jump to Section 4.


10/31


11/31

ROI-S04629

- 9-

(5) Check on Dial-up connectionand click on Nextbutton to continue.

(6) On the Network Connection Wizard window, type in Pnms001on the allocatedbox. Click on Nextbutton to continue.


12/31

ROI-S04629

- 10-

(7) Enter any number in the Phone number box. Click on Next button to continue.

(8) Verify that the connection Pnms001is registered. You can also create a shortcuton your desktop if you need. Click on Finishbutton.


13/31

ROI-S04629

- 11-

(9) On the Connect Dial-up Connection window, click on Cancelbutton to continue.Click Propertiesbutton on Connect Dial-up Connections window.

(10) On the Dial-up Connection Properties window, verify that selected device isModem- Standard 19200 bps Modem [COM1]on the General tab. Click on theConfigurebutton.


14/31

ROI-S04629

- 12-

(11) On the Modem Configuration window, uncheck all five boxes.

(12) On the Option tab, keep default setting and click on the Security tab.


15/31

ROI-S04629

- 13-

(13) On the Security tab, keep default setting and click on the Networking tab.

(14) On the Networking tab, verify that Type of dial-up server I am call ing is set toPPP and uncheck File and Printerand Client for Microsoft options.


16/31

ROI-S04629

- 14-

(15) Click on Settingsbutton. Uncheck all the boxes on the ensuing window just asshown in figure below. Click OK go back and highlight Internet Protocol (TCP/IP)then click on the properties box.

(16) Verify that both Obtain an IP address automatically and Obtain DNS serveraddress automatically are selected. Click on Advanced button.


17/31

ROI-S04629

- 15-

(17) On the Advanced TCP/IP Settings window, uncheck Use IP header compressionin the PPP link. Click OK button.

(18) On the Advanced tab, keep default setting and click OK button.


18/31

ROI-S04629

- 16-

4. LAN Setting

(1) Network Connections is displayed. Right click the Local Area Connection andselect Propertiesin LAN or High-Speed Internet category.

(2) On the Local Area Connection Properties window, verify that Internet ProtocolTCP/IP)is checked on the General tab. Click on the Propertiesbutton.


19/31

ROI-S04629

- 17-

(3) Verify that Use the following IP address is selected and input the IP address,Subnet mask, Default gateway assigned to the PNMS PC.

(4) Click on Advancedbutton. Verify that it is a value as set up at (3) on the IPSettings tab.


20/31

ROI-S04629

- 18-

(5) On the Authentication tab, keep default setting and click Advanced tab.

(6) On the Advanced tab, keep default setting and click OK button.


21/31

ROI-S04629

- 19-

5. PNMS Setup

(1) Insert the PNMS Installation CDROM on your CDROM drive. Open theCDROM folder and double-click the setup.exe.

(2) Click Next.


22/31

ROI-S04629

- 20-

(3) Specify the folder where you want to install the PNMS files. Then click Nextbutton.

(4) Click Nextbutton on the ensuing window to confirm the installation.


23/31

ROI-S04629

- 21-

(5) A message window will appear to confirm, the successful installation of thePNMS application. Click on Closebutton, to complete the installation.

(6) Check the contents of the Pnms folder.


24/31

ROI-S04629

- 22-

6. Launching PNMS

(1) Click on Start | Programs | PNMS | PNMSto start the application.

(2) Default user name and password are:

After installation of PNMS, Initial password is listed below.

User name: Admin

Password: (No initial password defined. J ust press on Enter key.

The password can then be modified.)


25/31

ROI-S04629

- 23-

7. NetConfigTool Setup

(1) Double-click the setup.exein the NetCfgTool folder in the Installation CD-ROM.

(2) The NetCfgTool installer might prompt you to close some applications (i.e. MSWord, Outlook Express, etc.) before you can continue installation. Close thisapplications and click on Retry button to resume with the NetCfgToolinstallation.

(3) In some cases, NetCfgTool installer might prompt you to restart your PC toupdate the Windows Installer. In this case, click on Yes button and wait for yourPC to restart. The NetCfgTool will automatically resume after your PC isrestarted.


26/31

ROI-S04629

- 24-

(4) The NeCfgTool Setup Wizard window will be started. Select RemoveNetCfgTool and click onFinish button to continue removing old NetCfgToolsoftware. I f this is a new installation of the NetCfgTool software please proceedto step 7.

(5) The removal progress will be shown in the ensuing window.


27/31

ROI-S04629

- 25-

(6) The NetCfgTool Setup Wizard wil l prompt you when your installation is complete.You should be able to see NetCfgTool has been successfully removed on thiswindow to confirm that you have removed a old application on your PC. Click onClosebutton to exit the installation wizard.

(7) Double-click the setup.exein the NetCfgTool folder in the Installation CD-ROM.


28/31

ROI-S04629

- 26-

(8) The NeCfgTool Setup Wizard window will be started. Click on Next button tocontinue installing NetCfgTool.

(9) On the next window, you will be prompted to specify the folder where you wantto install NetConfig Tool. Then click on Nextbutton after specifying theinstallation folder.


29/31

ROI-S04629

- 27-

(10) Click on Nextbutton on the ensuing confirmation window to start theinstallation of NetConfig Tool.

(11) The progress of your installation will be shown in the ensuing window. DO NOTclick on the Cancelbutton at this point. Clicking on the Cancel button mightcorrupt your files.


30/31

ROI-S04629

- 28-

(12) The NetCfgTool Setup Wizard will prompt you when your installation is complete.You should be able to see NetCfgTool has been successfully installed on thiswindow to confirm that you have installed a good copy of the application on yourPC. Click on Closebutton to exit the installation wizard.

(13) Please verify new NetCfgTool software version on PNMS to judge success foryour installation.

(14) From your Start Menu, select Programs PNMS PNMSto start theapplication.

(15) Click on NetworkConfiguration| Edit in the Menu bar on the main PNMSwindow.


31/31

ROI-S04629

(16) The NetCfgTool window will be started. Click on Help| About NetCfgTool inthe Menu bar on the NetCfgTool window. Please verify new NetCfgTool softwareversion.

Documents

PNMS Installation Manual WXP (S462961E)