Plumbing Submittal - Hajoca · Plumbing Submittal FAIRLESS CREDIT Submitted by MYSTIC MECH 1/12/2016 ... plomberie sans plomb L’entrée à souder est conforme à la norme ANSI B16.18

Plumbing SubmittalPlumbing SubmittalPlumbing SubmittalPlumbing Submittal

FAIRLESS CREDITFAIRLESS CREDITFAIRLESS CREDITFAIRLESS CREDIT

Submitted bySubmitted bySubmitted bySubmitted by

MYSTIC MECHMYSTIC MECHMYSTIC MECHMYSTIC MECH

1/12/20161/12/20161/12/20161/12/2016

WEINSTEIN SUPPLYWEINSTEIN SUPPLYWEINSTEIN SUPPLYWEINSTEIN SUPPLY

660 E. MAIN STREETNORRISTOWN, PA 19401

Phone: 610 279-3506Fax: 610 279-8050

www.weinsteinsupply.com

Spec#Spec#Spec#Spec# Table of ContentsTable of ContentsTable of ContentsTable of Contents

1 ............************************************************************************************************************HWC-1 HANDICAP WATER CLOSETHWC-1 HANDICAP WATER CLOSETHWC-1 HANDICAP WATER CLOSETHWC-1 HANDICAP WATER CLOSET************************************************************************************************************

2 700471 KOHLER K-3493-RA-0 WHT HIGHLINE 2PC 12 RGH-IN1.6GPF RH COMFORT HEIGHT ELONG TOILET

3 1123269 MAINLINE ML1055SSC000 WHT ELONG PLAS OPENFRONT TOILET SEAT W/ SELF-SUSTAINING CHECKHINGE & SS HARDWARE L/ COVER

4 1120540 MAINLINE ML15200 1/4X21/4 BRASS CLOSET BOLTS W/DBL NUT & WASHERS

5 937753 MAINLINE MLQTCS40BCX POL CHROME 1/2X3/8SWTXCOMP ANGLE QTR TURN STOP VLV W/ OVAL HDLLEAD FREE

6 937231 *X* MAINLINE MLB112DLF 3/8X7/8X12 COMPXBALLCOCKBRAIDED SS TOILET CONN (same as 0298044 or79120612)

7 ............****************************************************************************************HLAV-1 HANDICAP LAVATORYHLAV-1 HANDICAP LAVATORYHLAV-1 HANDICAP LAVATORYHLAV-1 HANDICAP LAVATORY************************************************************************************************

8 20874 KOHLER K-2005-0 WHT VC KINGSTN 211/4X181/8X121/43H WM 4CC LAV BASIN

9 263634 MOEN L4601 POL CHROME CHATEAU 3H DM 4CC SGLLEVER HDL LOW ARC LAV FCT L/ POP-UP

10 825694 MAINLINE ML760 11/4X6 CP 17GA BRASS COMMTAILPIECE W/ OPEN GRID STR

11 825762 MAINLINE ML705BBO 11/2 CP 17GA BRASS P-TRAP W/BRASS NUT & BOX ESC L/ CLEANOUT


13 937181 MAINLINE MLB112AF 3/8X1/2X12 COMPXFIP BRAIDEDSS LAV CONN LEAD FREE

14 1017492 MAINLINE ML102EZ WHT LAV-GUARD TRAP & SUPPLYCOVER F/ TUBULAR P-TRAP 2-ANGLE STOP & 2-SUPPLY ADA APPROVED


15 ............********************************************************MS-1 MOP BASINMS-1 MOP BASINMS-1 MOP BASINMS-1 MOP BASIN********************************************************

16 61265 FIAT MSB2424 24X24 WHT MOLDED STONE MOP SINK

17 1048152 MAINLINE XD141-RC RGH CHROME XD 2H WM 8CC 2METAL LEVER HDL MOP SINK FCT W/ HOSE END & PAILHOOK ADA APPROVED

18 6709 FIAT 889CC 24 MOP HGR BRKT

19 78573 FIAT 833AA SILICONE SEALANT

20 11036 FIAT MSG2424 SS WALL GUARD

21 ............********************************************************FD-1 FLOOR DRAINFD-1 FLOOR DRAINFD-1 FLOOR DRAINFD-1 FLOOR DRAIN****************************************************************************

22 205645 JRS 2005B FLOOR DRAIN

23 ............****************************************************************************************FCO-1 FLOOR CLEAN OUTFCO-1 FLOOR CLEAN OUTFCO-1 FLOOR CLEAN OUTFCO-1 FLOOR CLEAN OUT************************************************************************************

24 268076 JRS 4020LNB 3 NB FLR CO

25 ............****************************************************************************HEWC-1 WATER COOLERHEWC-1 WATER COOLERHEWC-1 WATER COOLERHEWC-1 WATER COOLER********************************************************************************

26 584682 ELKAY EZSTL8LC GRAY GRANITE ADA WM BI-LEVELWATER COOLER


28 937779 MAINLINE MLQTR04RX RGH BRASS 1/2X1/4 SWTXCOMPSTRAIGHT QTR TURN STOP VLV W/ OVAL HDL LEADFREE


29 ............****************************************************************RD-1 ROOF DRAINRD-1 ROOF DRAINRD-1 ROOF DRAINRD-1 ROOF DRAIN****************************************************************

30 834277 JR SMITH 1015-R-C-CID-4 1015-C-R-CID-4NH

31 1492354 JR SMITH 1620T03-B4-NB-WD02 3 THRD NIC BRZGUTTER DRAIN W/4 DEEP BODY BOT OUT & LOWDOME W/2" INT WTR DAM

32 ............****************************************************************************EWH-1 WATER HEATEREWH-1 WATER HEATEREWH-1 WATER HEATEREWH-1 WATER HEATER****************************************************************************************

33 1397253 BRADFORD WHT RE230L6-1NCWW 240V 1PH 4.5KW/4.0KW NON-SIM 28GAL LOWBOY ENERGY SAVER ELECRES WTR HTR 29-7/8H 22DIA W/ T&P VLV 6 YEARWARRANTY

34 ............****************************************************************HSK-1 KITCHEN SINKHSK-1 KITCHEN SINKHSK-1 KITCHEN SINKHSK-1 KITCHEN SINK********************************************************************************

35 1046016 JUST SL-ADA-17519-A-GR (3) HOLES ON 4" CENTER (8"),CENTER DRAIN

36 669553 MOEN 8701 POL CHROME COMM M-BITION 1H DM SGLLEVER HDL KITCHEN FCT W/ OPTIONAL 3H ESC PLATE

37 825678 MAINLINE MLL7 FORGED BRASS METAL POST BSKTSTR ASSY W/ SS BSKT



40 937181 MAINLINE MLB112AF 3/8X1/2X12 COMPXFIP BRAIDEDSS LAV CONN LEAD FREE

41 ............****************************************************ELEVATOR PUMPELEVATOR PUMPELEVATOR PUMPELEVATOR PUMP********************************************************


42 739018 LIBERTY ELV280 22.65 HEIGHT CI 1/2HP 1PH 115VELEVATOR SUMP PUMP SYS W/ OILTECTOR CONTROL& ALARM

43 64054 LEGEND 203-227 S-613 1-1/4 / 1-1/2 CPLG ABS FULLFLOW SUMP PUMP CHECK VLV W/ SS CLAMPS

44 65433 11/2 SCH40 PVC SXS UNION 457-015

45 1460462 55100 INCOMING FREIGHT CHARGES

Spec Seq#: 1

***************************HWC-1 HANDICAP WATER CLOSET

***************************

Spec Seq#: 2

7004

71

Spec Seq#: 2

7004

71

Mainline Plastic CommercialElongated Toilet Seat | rev. 07-6-2012

PRODUCT SPECIFICATIONS

All dimensions listed are nominal. MAINLINE® reserves the right to make product and material changes at any time without notice.

Contact your sales representative for more information or visit our website at mainlinecollection.com

WarrantySee warranty information for more details.

ML1055/ML1055SSC

Plastic Commercial Elongated Toilet SeatDescriptionOpen front less cover, elongated, heavy-duty, injection molded solid plastic toilet seat. Features two molded-in bumpers, non self-sustaining (1055) or self-sustaining (1055SSC) check hinges with non-corrosive 300 Series stainless steel posts, pintles and hardware. This seat complies with American National Standard Z124.5 Toilet (Water Closet) Seats as a class Commercial Heavy Duty.

PLASTIC HINGES WITH STAINLESS STEEL POSTS

AND PINTLES

NON-CORROSIVE STAINLESS STEEL

HARDWARE

3-3/4"

18-5/16" 8-1/8" 17-7/8"

14-3/8"

5-1/2"

13/16"1"

Specifications

Size: Elongated

Weight: 2.9 lbs

Color: White (000)

Material: Plastic

Style: Open Front less Cover

Bumpers: Two

Hinges: Plastic Non Self-Sustaining (1055) or Self-Sustaining (1055SSC) with 300 Series Stainless Steel Posts and Pintles

Fastening System: Non-Corrosive 300 Series Stainless Steel Hardware

ML1055 ML1055SSC

Spec Seq#: 3

1123

269

To Submit Part No. Description

ML15200 1/4”X2-1/4” Brass Closet Bolts Double Nut/Washer

ML15205 1/4”X2-1/4” Brass Closet Bolts with Retainer

ML15230 1/4”X3-1/2” Brass Closet Bolts Double Nut/WasherML15235 1/4”X3-1/2” Brass Closet Bolts with RetainerML15255 5/16”X2-1/4” Brass Closet Bolts with RetainerML15280 5/16”X3-1/2” Brass Closet Bolt with Retainer


ML15210 1/4”X2-1/4” Brass Plated Closet Bolts

ML15215 1/4”X2-1/4” Brass Plated Closet Bolts Double Nut/Washer

ML15220 1/4”X2-1/4” Brass Plated Closet Bolts with RetainerML15240 1/4”X3-1/2” Brass Plated Closet BoltsML15245 1/4”X3-1/2” Brass Plated Closet Bolts Double Nut/WasherML15250 1/4”X3-1/2” Brass Plated Closet Bolts with RetainerML15260 5/16”X2-1/4” Brass Plated Closet BoltsML15265 5/16”X2-1/4” Brass Plated Closet Bolts Double Nut/WasherML15270 5/16”X2-1/4” Brass Plated Closet Bolts with Retainer


ML15225 1/4”X2-1/4” Brass Snap Closet Bolts with Retainer

ML15275 5/16”X2-1/4” Brass Snap Closet Bolts with Retainer

1 OF 1

Mainline Closet Bolts | rev. 05-15-2012

PRODUCT SPECIFICATIONS

WarrantySee warranty information for more details.

All dimensions listed are nominal. MAINLINE® reserves the right to make product and material changes at any time without notice.

Contact your sales representative for more information or visit our website at mainlinecollection.com

Closet BoltsProduct FeaturesMainline closet bolts come in a variety of configurations and types to make any toilet installation trouble-free.

Brass Snap Closet BoltsMainline solid brass snap closet bolts are different because if the closet bolt is too long, the excess can be snapped off and no cutting is required. These bolts are also uniquebecause there is no captive metal washer. Instead, there is a plastic washer which helpshold the closet bolt in an upright position for a straightforward installation.

Brass Plated Closet BoltsMainline brass plated closet bolts are steel bolts plated with a brass coating.

Brass Closet Bolts Mainline brass closet bolts are made from solid brass and properly secure the toilet to the floor.

Spec Seq#: 4

1120

540

● CS40B C● CS40BX C

MLQTCS40BCX

NSF/ANSI 61

Cross ReferenceReferencias adicionalesRéférences

Features / Caractéristiques / Características● Chrome Plated● Includes Bell Escutcheon and 5” Extension● Easy Quarter Turn Operation● Inlet ‐ 1/2” Sweat● Outlet ‐ 3/8” O.D. Comp. ● Material: Machined One Piece Brass Body● Lead Free (≤ .25% Pb)

● Plaqué chrome● Inclut écusson en forme de cloche et extension de 5 po● Commande quart de tour facile● Entrée ‐ 1/2 po à braser● Sortie – dia. ext. 3/8 po à compression● Matériau : Corps en laiton usiné d’une seule pièce● Sans plomb (≤ .25% Pb)

● Acabado en cromo● Incluye cartucho campana y extensión de 5”● Funcionamiento fácil, cuarto de vuelta● Entrada – 1/2” con soldadura● Salida – diámetro exterior de 3/8”, a compresión● Material: cuerpo de bronce en una pieza● Sin plomo (≤ .25% Pb)

Operating Specifications / Caractéristiques de fonctionnement / Especificaciones de funcionamiento● Temperature: 40° to 140° Fahrenheit● Pressure: 125 PSI Maximum

● Température : 40 °F à 140 °F● Pression : 125 psi maximum

● Temperatura: de 40° a 140° Fahrenheit● Presión: Máxima 125 PSI

Compliance / Conformité / Cumplimiento de regulaciones● Complies with Lead‐Free Plumbing Laws● Solder Inlet Complies with ANSI B16.18

● Conforme à la réglementation sur le matériel de plomberie sans plomb

● L’entrée à souder est conforme à la norme ANSIB16.18

● Cumple con las regulaciones sobre el plomo libre de material de fontanería

● Las entradas a soldadura cumplen con ANSI B16.18

Certifications / Certifications / Certificaciones

● CUPC● CSA ● NSF61‐9

Spec Seq#: 5

9377

53

CLOSET CONNECTOR 3/8” COMP. x 7/8” BALLCOCK

• Braided Stainless Steel with Non-toxic PVC Inner Core

• Rated Water Pressure: up to 125psi

• Maximum Temperature: 180°F

• Limited 5 Year Warranty from Date of Purchase

• IAPMO listed to ASME A112.18.6

No. Part Name Material

1 Hex Nut Forged Brass, C37710

2 Washer NSF Compliant EPDM

3 Barb Forged Brass, Low Lead

4 Ferrule SS 304

5 Hose SS+NSF Approved PVC

6 Nut POM

7 Barb Forged Brass, Low Lead


www.mainlinecollection.com

SPECIFICATIONS

Model # MLB19DLF MLB112DLF MLB116DLF MLB120DLF

Length 9" 12" 16" 20"

Spec Seq#: 6

9372

31

http://www.mainlinecollection.com/default.aspx

Spec Seq#: 7

**********************HLAV-1 HANDICAP LAVATORY

************************

Spec Seq#: 8

2087

4

Spec Seq#: 8

2087

4

Spec Seq#: 9

2636

34

Spec Seq#: 9

2636

34

ML760 GRID DRAIN

SPECIFICATIONS

19-HOLE COMMERCIAL GRID DRAIN

• 1-1/4” Forged Brass Construction

• 6” 17 GA Tailpiece

• Chrome Plated

ML760


1 Grid Body Brass

2 Washer Brass

3 Friction Washer Paper

4 Locknut Zinc

5 Tailpiece Brass

Cross Reference

760-1 D70-100

5680PC FY-155

155A Z8743-PC


CERTIFICATIONS • cUPC

Spec Seq#: 10

8256

94

ML705 TUBULAR P-TRAP

1-1/2” TUBULAR LESS CLEANOUT

• 8-3/4” 17 GA Brass Wall Tube

• Chrome Plated


1 Wall Tube Brass

2 J-Bend Brass

Model# Options

ML705BBO Brass Nut Kit, Box Escutcheon

ML705BDE Brass Nut Kit, Deep Bell Escutcheon

ML705BSH Brass Nut Kit, Shallow Escutcheon

ML705ZBO Zinc Nut Kit, Box Escutcheon

ML705ZDE Zinc Nut Kit, Deep Bell Escutcheon

ML705ZSH Zinc Nut Kit, Shallow Escutcheon

Box Escutcheon

Deep Bell Escutcheon

Shallow Escutcheon



SPECIFICATIONS

1-1/2"(

38.1mm)

8.66"(220mm)3.22"(82mm)

11.89"(302mm)

4.72"(120mm)

1.52"( 38.5mm)

2.95"( 75mm)

1.5"( 38.1mm)

1.42"(36mm)

2.99"( 76mm)

1.5"( 38.1mm)

1.42"(36

mm)

Spec Seq#: 11

8257

62

http://www.mainlinecollection.com/


MLQTCS40BCX

NSF/ANSI 61















Spec Seq#: 12

9377

53

LEAD FREE*

LAVATORY CONNECTOR 3/8” Comp. x 1/2” FIP





• IAPMO listed to ASME A112.18.6 and CSA B125.6-2009

• Complies with Lead-Free Plumbing Laws

• *≤ .25% Pb




3 Barb Forged Brass, No Lead

4 Ferrule SS 304



7 Washer NSF compliant EPDM


SPECIFICATIONS

Model # MLB112AF MLB116AF MLB120AF MLB130AF

Length 12" 16" 20" 30"

Spec Seq#: 13

9371

81


Model ML101EZOne P-trap cover, one anglevalve and supply covers

General Description:MAINLINE® EZ Series waste and supply piping covers satisfy ADA compliance requirements. Built-inEZ Grip internal fasteners and internal, EZ Tear-To-Fittrimming feature allow for fast installation without tools.

cover kits are designed to �t on all tubularand cast brass P-trap assemblies. Valve cover completelyencloses angle valve and supply tube for both handledand keyed type water stops.

____________________________________________Material Molded vinyl____________________________________________Nominal Wall 1/8" constant____________________________________________Durometer 70 -80 - Shore A____________________________________________UV Protection Will not fade or discolor____________________________________________Durability Virtually indestructible____________________________________________Trimming (EZ Series) Internal EZ Tear-To-Fit

trim feature____________________________________________Fasteners (EZ Series) Internal EZ Grip fasteners

(reusable)____________________________________________Color China white____________________________________________Paintability Apply Latex paint____________________________________________Burning CharacteristicsASTM D-635 ____________________________________________Bacteria/Fungus Resistance ____________________________________________Maintenance Use common detergents____________________________________________

Submittal SheetADA-compliant undersink protection

MAINLINE reserves the right to make product and material changes at any time without notice.

Job/Location ____________________________ ____________Designer _________________________________________

Model ML102EZOne P-trap cover, two angle valveand supply covers

Model ML103EZOne P-trap cover, two angle valveand supply covers, one 5" o�setwheelchair strainer cover

Model ML105EZOne 5" o�set wheelchair strainercover

#100 E-Z Series (shown above right) for tubular and cast brass P-trap assemblies.

Manufactured under one or more of the following U.S. or Canadian patents.Other patents pending.5,303,730 5,360,031 5,524,669 5,564,463 5,678,598 5,699,828 5,915,4125,915,413 5,901,739 5,960,820 2,075,324 2,119,427 2,136,027 2,158,083

10" waste arm cover with internalEZ Tear-To-Fit trim feature

9" supply tube cover with internal EZ Tear-To-Fit trim grooves

J-bend covers all tubular and cast brass

con�gurations

Internal ribs add cushioning and thermal resistance

10" tailpiece cover

EZ Tear-To-Fit trim grooves

EZ Grip internal fasteners

Vent hole keeps P-trap dry

Vent slots keepvalve dry

Install over pipes. Press �ngerrecesses to engageinternal fasteners.To remove covers,�rmly pull seamapart using a strong grip.

Tear-to-�t on internal

dimensioned tear lines.

Shown with Accessory ML105EZ (�ts all standard 5" o�set wheelchair strainers)

NOTE: Accessory ML105EZ is included in ML103EZ kits.

EZSeriesShown

MAINLINE

Self extinguished0 sec (ATB) 0 mm (AEB)

ASTM G21 and G22/Result: 0 growth

®

®

Spec Seq#: 14

1017

492

Spec Seq#: 15

**************MS-1 MOP BASIN

**************

FEATURES

NOTES

CR/PL© 04/03 Printed in U.S.A.

OPTIONS

FIAT PRODUCTSA CRANE PLUMBING COMP ANY

¤

MOLDED-STONE®

MOP SERVICE BASIN

MSB 2424MSB 3624

Molded-Stone® Mop Service Basin

• MSB 2424

The MSB 2424 shall have overall outside dimensions of 24” x 24” x 10”. The molding shall be done in matched metal dies under heat and pressure resulting in a one-piece homogeneous product. The unit shall have 10”high walls with not less than 1” wide.

The stainless steel drain body is designed to provide for a caulk connection or QDC-3 joint to a 3” drain pipe. A combination dome strainer and lint basket made from stainless steel shall be included with factory installed stainless steel drain body for caulked joint to accept a 3” pipe.

• MSB 3624

The MSB 3624 shall have overall outside dimensions of 36” x 24” x 10”. The molding shall be done in matched metal dies under heat and pressure resulting in a one-piece homogeneous product. The unit shall have 10”high walls with not less than 1” wide shoulders and an integrally molded shelf 10 9⁄16” wide whereindicated.

The stainless steel drain body is designed to provide for a caulk connection or QDC-3 joint to a 3” drain pipe. A combination dome strainer and lint basket made from stainless steel shall be included with factory installed stainless steel drain body for caulked joint to accept a 3” pipe.

• Service Faucet (830-AA): Chrome plated with vacuum breaker, integral stops, adjustable wall brace, pail hook and 3⁄4” hose thread on spout.

• Hose and Hose Bracket (832-AA)

• Mop Hanger (889-CC)

• Alternate Strainer (1453-BB) - For residential use (EFS-3624 and EFS-2424)

• 3” Quick Drain Connector (QDC-3XH): Neoprene connecting gasket suitable for attaching extra heavy cast iron soil pipe and Schedule 40 steel pipe to the drain body. Neoprene connecting gasket (QDC-3SN) suitable for attaching hubless cast iron pipe (no hub, nominal O.D. of 3.31”) and service weight cast iron soil pipe (nominal O.D. of 3.38”) to the drain body.

• Silicone Sealant (833-AA)

• Vinyl Bumperguard (E-77-AA)

• Stainless Steel Bumperguard (E-88-AA)

• Stainles Steel Wall Guard (MSG2424, MSG2828, MG3232, MSG3636, and MSG3624)

Spec Seq#: 16

6126

5

IMPORTANT: Roughing-in dimensions may vary 1/2" and are subject to change or cancellation without prior notice.CR/PL© 04/03 Printed in U.S.A.


¤

Molded-Stone® Mop Service Basin

MSB 2424MSB 3624

MOLDED-STONE®

MOP SERVICE BASIN

Spec Seq#: 16

6126

5

XD141-RC

AVAILABLE FINISHES / FINIS OFFERTS / DISTINTOS ACABADOS:• Rough Chrome / Chrome brut / Cromo tosco (CP)

8” Mop Service Sink FaucetRobinet de poste d’eau, 8 po

Grifo de 8” para fregadero de servicio

FEATURES• Brass Waterways• Integral Stops• Adjustable 7-1/4"~ 8-3/4" Inlet Centers• 3/4" Hose End• Vacuum Breaker• Pail hook• Ceramic Disc Cartridges• Vandal Resistant Handles• Max Flow Rate: 10.56 GPM @ 60 PSI• 100% Factory Pressure Tested

CARACTÉRISTIQUES• Voies d’alimentation en laiton• Butées intégrées• Centres des orifices d'entrée réglables de 7-1/ 4~ 8-3/4 po• Extrémité pour boyau de 3/4 po• Casse-vide• Accroche-seau• Cartouches disque céramique• Manettes antivandalisme• Débit maximum: 10,56 gal/min à 60 lb/po²• Pression vérifiée en usine- 100%

CARACTERÍSTICAS• Tuberías de bronce• Cortes integrados• Centros de entrada ajustables de 7-1/4"~ 8-3/4"• Terminación de manguera de 3/4" • Interruptor de vacío• Gancho para el balde• Cartuchos de disco cerámico• Manijas con protección contra vandalismo • Flujo máximo: 10,56 GPM @ 60 PSI • Probado en fábrica bajo presión al 100%

APPLICABLE STANDARDS/CODESSpecified model meets or exceeds the following:

NORMES ET CODES APPLICABLESLe modèle spécifié est conforme aux normes suivantes ou les dépasse:

NORMAS Y ESTÁNDARES APLICABLESEl modelo especificado reúne o sobrepasa las siguientes condiciones• IAPMO/cUPC• ADA

Spec Seq#: 17

1048

152

XD141-RC

PRODUCT SPECIFICATIONSFICHE TECHNIQUE DU PRODUIT

ESPECIFICACIONES DEL PRODUCTO

Spec Seq#: 17

1048

152

• GENERAL:Model No. 889-CC is 24" long x 3" wide, stainless steel with three (3) rubber tool grips. This is used with the 36" x 24" x 10" Molded-Stone Mop Service Basin with Shelf (MSB-3624) and the 24" x 24" x 10" Molded-Stone Mop Services Basin less Shelf (MSB-2424).

FEATURES

NOTES

889-CCMOP HANGER

CR/PL© 09/02 Printed in U.S.A.* Not furnished by Fiat Products. Description for specification purposes only.

OPTIONS


¤

Spec Seq#: 18

6709

• GENERAL: Model No. 833-AA standard 1/12th gallon cartridge for use with open type, hand operated caulking gun. This permanent sealant is an elastomer vastly superior to conventional caulking compounds; will not crack, shrink or change color. This sealant is used with the 36" x 24" x 10" Molded-Stone Mop Service Basin with Shelf (MSB-3624) and the 24" x 24" x 10" Molded-Stone Mop Services Basin less Shelf (MSB-2424).

FEATURES

NOTES

833-AASILICONE SEALANT


OPTIONS


¤

Spec Seq#: 19

7857

3

• GENERAL: Model No.s MSG2424, MSG2828, MSG3232, MSG3636 and MSG3624 are used with the 36" x 24" x 10" Molded-Stone Mop Service Basin with Shelf (MSB-3624) and the 24" x 24" x 10" Molded-Stone Mop Services Basin less Shelf (MSB-2424).

FEATURES

NOTES

MSG2424 , MSG2828MSG3232 , MSG3636 MSG3624

STAINLESS STEEL WALL GUARDS


OPTIONS


¤

Spec Seq#: 20

1103

6

MSG2424 , MSG2828MSG3232 , MSG3636 MSG3624

STAINLESS STEEL WALL GUARDS

IMPORTANT: Roughing-in dimensions may vary 1/2" and are subject to change or cancellation without prior notice.CR/PL© 09/02 Printed in U.S.A.


¤

Spec Seq#: 20

1103

6

Spec Seq#: 21

**************FD-1 FLOOR DRAIN

*******************

Spec Seq#: 22

2056

45

Spec Seq#: 23

**********************FCO-1 FLOOR CLEAN OUT

*********************

NO

NE

RK

FLOOR CLEANOUTS WITH "TWIS-TO-FLOOR®"ADJUSTABLE TOPS FOR UNFINISHED AREAS

ROUND EXTRA HEAVY DUTY CAST IRON TOPFUNCTION: Used in floors and areas where appearance of cast iron is satisfactory. Will withstand heavy load traffic.

REGULARLY FURNISHED: VARIATIONS:Flashing Flange -FFlange with Flashing Clamp -F-CVandal Proof Top -U

OPTIONAL MATERIALS:Galvanized Cast Iron -GDuctile Iron Cover -M

4220 SERIES

4220

SE

RIE

S2-

16-7

0JM

BH

S42

20

plug.)

NOTE: Dimensions shown inparentheses are in millimeters.

Fig. 4220S.....Gasket Seal - ABS Plug Fig. 4221S.....Gasket Seal - Bronze Plug Fig. 4223S.....Taper Thread - Bronze Plug Fig. 4224S.....Taper Thread - ABS Plug

REV. DATE DESCRIPTION BY CKD. BY

WEIGHTPOUNDS

VOLUMECUBIC FEET

FIGURE NUMBER

LOCATIONF

IGU

RE

NU

MB

ER

DIM

EN

SIO

NS

AR

E S

UB

JEC

T T

O M

AN

UFA

CT

UR

ER

S T

OLE

RA

NC

E A

ND

CH

AN

GE

WIT

HO

UT

NO

TIC

EW

E C

AN

AS

SU

ME

NO

RE

SP

ON

SIB

ILIT

Y F

OR

US

E O

F S

UP

ER

SE

DE

D O

R V

OID

DAT

A

DR

AW

N B

Y:

CH

EC

KE

D B

Y:

AP

PR

OV

ED

BY

:D

AT

E:

SC

ALE

:S

IZE A

DR

AW

ING

NU

MB

ER

Adj. Top and Frame"C.O." cast in Secured Cover

A

P

4"(100)

Min. 3 5/16"(84)Max. 4 1/2"(115)

Duco Cast Iron Cleanout with RoundAdjustable Scoriated Secured CastIron Top. Closure Plug Type asIndicated By Figure Number Selected.

3 1/2"(89)

6"(150) DIA.

9"(230) DIA.

Plug Size

2 3/16"(56)

Flashing Flange(when specified)

Flashing Clamp(when specified)

TWIS-TO-FLOOR® ADJUSTMENT

NO-HUB OUTLET

"A" (Pipe Size) = 02(50), 03(75) or 04(100)

(Twis-to-Floor ® design shown with gasketed

JAY R.SMITH MFG. CO. ®

DIVISION OF SMITH INDUSTRIES, INC.POST OFFICE BOX 3237MONTGOMERY, ALABAMA 36109-0237 (USA)TEL: 334-277-8520 FAX: 334-272-7396 www.jrsmith.comCUSTOMER

DRIVEN

SMITH®

MEMBER OF:

®

ASPE®

SANITARY

EN G IN E E RINGPrevention Rather Than Cure

N 12/17/04 JJ

7"(180) DIA.

CLAdded Width Dimension at TopP 05/08/07 JJ CLRevised Outlet Text

Spec Seq#: 24

2680

76

NO

NE

RN

FLOOR CLEANOUTS WITH "TWIS-TO-FLOOR " ADJUSTABLE TOPS FOR UNFINISHED AREAS

ROUND EXTRA HEAVY DUTY CAST IRON TOP

REGULARLY FURNISHED: Duco Cast Iron Cleanout with TaperThread Bronze Plug and RoundAdjustable Scoriated Secured CastIron Top.

VARIATIONS: Flashing Flange -FFlange with Flashing Clamp -F-CVandal Proof Top -U

OPTIONAL MATERIALS:Galvanized Cast Iron -GDuctile Iron Cover-M

4223

4223

5-5-

06S

4220

BS


SPIGOT OUTLET

SPIGOT OUTLET

Fig. 4223S....................Taper Thread - Bronze Plug

Sized for Service Weight and/or NO-HUB.

"TWIS-TO-FLOOR " ADJUSTMENT


WEIGHTPOUNDS

VOLUMECUBIC FEET

FIGURE NUMBER

LOCATIONF

IGU

RE

NU

MB

ER

DIM

EN

SIO

NS

AR

E S

UB

JEC

T T

O M

AN

UFA

CT

UR

ER

S T

OLE

RA

NC

E A

ND

CH

AN

GE

WIT

HO

UT

NO

TIC

EW

E C

AN

AS

SU

ME

NO

RE

SP

ON

SIB

ILIT

Y F

OR

US

E O

F S

UP

ER

SE

DE

D O

R V

OID

DAT

A

DR

AW

N B

Y:

CH

EC

KE

D B

Y:

AP

PR

OV

ED

BY

:D

ATE

:S

CA

LE:

SIZ

E AD

RA

WIN

G N

UM

BE

R

A

"C.O." cast inSecured Cover

"A" (Pipe Size) = 06(150) & 08(200)

12 (305)

8(205)

8 1/2 (215) DIA.Adj. Top and Frame

Max. 3 1/2 (89) * Min. 1 1/2 (38)

6 (150) Plug Size

1 5/16 (34)

®

®

* When Flange-F is specified Min. 1 1/2 (38) becomes 2 (51)

Flashing Clamp(when specified)

Flashing Flange(when specified)

FUNCTION: Used in floors and areas where appearance of Cast Iron is satisfactory. Will withstand heavy load traffic.

CL

CE

LJAY R.SMITH MFG. CO.®


DRIVEN

SMITH®

MEMBER OF:

®

ASPE®

SANITARY

ENGINEERINGPrevention Rather Than C

ure

Spec Seq#: 24

2680

76

Spec Seq#: 25

*******************HEWC-1 WATER COOLER

********************

© 2014 ElkaySPEC12-24 (06/2014)

PRODUCT SPECIFICATIONSelf-contained wall mount electric two-level water cooler. Models EZ(S)TL8 and EZTL8 shall deliver 8 GPH of 50°F drinking water at 90°F ambient and 80°F inlet water. Models EZ(S)TLDD shall deliver non-chilled drinking water. Unit shall meetADA guidelines. Unit shall be lead-free design which is certified to NSF/ANSI 61 and 372 and meets Federal and State low-lead requirements. Unit shall be certified to UL399 and CAN/CSA 22.2 No. 120.

Models EZSTL have self-closing Easy-Touch pushbar controls on front & sides.Models EZTL have self-closing Easy-Touch pushbar controls on front only.Models EZ(S)TLDD are non-refrigerated. Requires outlet for power cord.

NOTE: Minimum 40 psi supply line pressure required in special circumstances where both sides of two-level are in use simultaneously to ensure adequate stream height.

STANDARD FEATURES• Easy-Touch pushbar activation• Extra deep basin minimizes splashing; with integral drain • Available with Flexi-Guard® Safety bubbler or Vandal-resistantt bubbler Vandal-resistantt bubbler (tincludes “VR” code in model no.)• Valve with built-in flow regulator to provide constant stream from 20 to 105 psi water pressure• *Versatile cooler design allows units to be installed either left-hand high and right-hand low or left-low and right high• Cooler panel finishes: Light Gray Granite Vinyl Clad Steel or Stainless Steel• Rated for Indoor Use

COOLING SYSTEM (Models EZ(S)TL(VR)8 only)• Compressor: Hermetically-sealed, reciprocating type, single phase. Sealed-in lifetime lubrication.• Condenser: Fan cooled, copper tube with aluminum fins. Fan motor is permanently lubricated.• Cooling Unit: Tube type. Self-cleansing. Continuous Copper tubing which is fully insulated with EPS foam that meets UL requirements for self-extinguishing material.• Refrigerant Control: Refrigerant R134a is controlled by accurately calibrated capillary tube.• Temperature Control: Easily accessible enclosed adjustable thermostat is factory preset. Requires no adjustment other than for altitude requirements.

CAPACITIES CHART

Model Voltage / Hertz Chilling**Capacity

F.L.Amps

Rated Watts

Approx.ShipWt.

UL399 and CAN/CSA 22.2

No. 120 Certified

ADA Compliant

ANSI/NSF 61 and 372 Certified

EZ(S)TL(VR)8*C 115V / 60Hz 8 GPH 4.0 370 72 lbs • • •EZ(S)TL(VR)8*2JOC 220V / 50Hz 6.7 GPH 2.0 370 72 lbs ++ • •EZ(S)TL(VR)DD*C 115V / 60Hz – 1.0 15 46 lbs • • •

*Color code of (L) Light Gray Granite or (S) Stainless Steel cooler panels.**Based on 80°F inlet water & 90°F ambient air temp for 50°F chilled drinking water.++Complies; not third party certified.

RATED FOR INDOOR USE ONLY

SPECIFICATIONS

Versatile Bi-Level Water CoolerPushbar Activated

Models EZ(S)TL8 and Model EZ(S)TLDD

CONSTRUCTION• Stainless Steel basin with integral drain• Galvanized structural steel cooler chassis provides structural integrity• Cooler cabinet available as Light Gray Granite Vinyl Clad Steel or Stainless Steel (additional cost) construction • Exclusive Flexi-Guard® Safety bubbler (option) utilizes an infused anti-microbial pliable polyester elastomer to prevent accidental mouth injuries. Flexes on impact.

Warranty: 5 year limited warranty on the unit’s refrigeration system. Electrical components andwater system are warranted for 12 months from dateof installation or 18 months from factory shipment, whichever date falls first.

2222 Camden CourtOak Brook, IL 60523

630-572-3192elkay.com

In keeping with our policy of continuing product improvement, Elkay reserves the right to change specification without notice. Please visit elkay.com for the most current version.

This specification describes an Elkay product with design, quality and functional benefits to the user. When making a comparison of other producer’s offerings, be certain these features are not overlooked.

*Versatile cooler configuration as shipped

*Versatile cooler configuration alternate installation

Spec Seq#: 26

5846

82

19"483mm

21 7/8"556mm

24 1/2"622mm

34 5/16"872mm

2"51mm

28 13/16"732mm

2"51mm

18 3/8"467mm

6 3/8"162mm

6 3/8"162mm

2"51mm

7"178mm

7"178mm

2"51mm

3 7/8"98mm

B

A(ALT. LOCATION)

F

F

18 3/8"467mm

9/32"7mm DIA. ((12)

E

E

6 3/8"162mm

6 3/8"162mm

DPREFFEREDLOCATION

19 7/16"494mm

13 15/16"354mm

7/8"22mm

22 15/16"583mm

5 3/4"146mm

17 7/16"443mm

FINISHED FLOOR

‰ ‰

APREFFEREDLOCATION

1 7/16"37mm

3"76mm

12 1/2"318mm

C

8 1/16"205mm

27"686mm

ADAREQUIREMENT

31 5/16"796mm

RIMHEIGHT

32 7/8"835mmORIFICEHEIGHT

36 13/16"936mm

RIMHEIGHT


19"483mm

HANGERBRACKET

RATED FOR INDOOR USE ONLYNOTICEThis water cooler must be connected to the water supply using a dielectric coupling. The cooler is furnished with a non-metallic strainer which meets this requirement. The drain trap which is provided by the installer should also be plastic to completely isolate the cooler from the building plumbing system.

IMPORTANT! INSTALLER PLEASE NOTE:These units are designed and built to provide water to the user which has not been altered by materials in the cooler waterway. The grounding of electrical equipment such as telephone, computers, etc. to water lines is a commonprocedure. This grounding may be in the building but may also occur away from the building. This grounding can cause electrical feedback into a water coolercreating an electrolysis which results in a metallic taste or an increase in the metal content of the water. This condition is avoidable by installing the coolerusing the proper materials as shown.

ROUGH-IN DIMENSIONS

LEGEND:A = Recommended Water Supply location. Shut-off Valve (not furnished) to accept 3/8” O.D. unplated copper tube. Up to 3” (76mm) maximum out from wall.B = Recommended Waste Outlet location. To accommodate 1-1/2” nominal drain. Drain stub 2” (51mm) out from wall.C = 1-1/2” Trap (not furnished).D = Electrical Supply (3) Wire Recessed Box Duplex Outlet.E = Insure proper ventilation by maintaining 6” (152mm) minimum clearance from cabinet louvers to wall.F = 7/16” (11mm) Bolt Holes for fastening to wall.NOTE: New Installations Must Use Ground Fault Circuit Interrupter (GFCI)

Printed in U.S.A.© 2014 Elkay

ROUGH-IN FOR LEFT-HAND HIGH SIDE MODELS


630-572-3192elkay.com

Page 2

Versatile Bi-Level Water CoolerPushbar ActivatedModels EZ(S)TL8 and Model EZ(S)TLDD

REDUCE HEIGHT BY 3 INCHES FOR INSTALLATION OF CHILDRENS ADA COOLER

Job Name: ____________________________________ Model: _______________________ Qty. ____________ Contact: ______________________________________ Approval Signature: _____________________________ Notes:

Model shown with Flexi-Guard® bubbler.

Spec Seq#: 26

5846

82

19 7/16"494mm

24 1/2"622mm

19"483mm

28 13/16"732mm

2"51mm

2"51mm

18 3/8"467mm

6 3/8"162mm

6 3/8"162mm

6 3/8"162mm

6 3/8"162mm

2"51mm

2"51mm

18 3/8"467mm

O9/32"7mm (12)

E

13 15/16"354mm

21 7/8"556mm

AREFERREDLOCATION

DALT. LOCATION

3 7/8"98mm

7"178mm

7"178mm

B

FF

DPREFFEREDLOCATION

A(ALT. LOCATION)

E

7/8"22mm

FINISHED FLOOR

‰ ‰

22 15/16"583mm

5 3/4"146mm

34 5/16"872mm

1 7/16"37mm

3"76mm

12 1/2"318mm

C

8 1/16"205mm

27"686mm

ADAREQUIREMENT

31 5/16"796mm

RIMHEIGHT


36 13/16"936mm

RIMHEIGHT


HANGERBRACKET

19"483mm

LEGEND:A = Recommended Water Supply location. Shut-off Valve (not furnished) to accept 3/8” O.D. unplated copper tube. Up to 3” (76mm) maximum out from wall.B = Recommended Waste Outlet location. To accommodate 1-1/2” nominal drain. Drain stub 2” (51mm) out from wall.C = 1-1/2” Trap (not furnished).D = Electrical Supply (3) Wire Recessed Box Duplex Outlet.E = Insure proper ventilation by maintaining 6” (152mm) minimum clearance from cabinet louvers to wall.F = 7/16” (11mm) Bolt Holes for fastening to wall.NOTE: New Installations Must Use Ground Fault Circuit Interrupter (GFCI)

RATED FOR INDOOR USE ONLY

NOTICEThis water cooler must be connected to the water supply using a dielectric coupling. The cooler is furnished with a non-metallic strainer which meets this requirement. The drain trap which is provided by the installer should also be plastic to completely isolate the cooler from the building plumbing system.

IMPORTANT! INSTALLER PLEASE NOTE:These units are designed and built to provide water to the user which has not been altered by materials in the cooler waterway. The grounding of electrical equipment such as telephone, computers, etc. to water lines is a commonprocedure. This grounding may be in the building but may also occur away from the building. This grounding can cause electrical feedback into a water coolercreating an electrolysis which results in a metallic taste or an increase in the metal content of the water. This condition is avoidable by installing the coolerusing the proper materials as shown.

REDUCE HEIGHT BY 3 INCHES FOR INSTALLATION OF CHILDRENS ADA COOLER

ROUGH-IN DIMENSIONS

Printed in U.S.A.© 2014 Elkay

ROUGH-IN FOR RIGHT-HAND HIGH SIDE MODELS


630-572-3192elkay.com

Page 3

Versatile Bi-Level Water CoolerPushbar Activated

Models EZ(S)TL8 and Model EZ(S)TLDD

Job Name: ____________________________________ Model: _______________________ Qty. ____________ Contact: ______________________________________ Approval Signature: _____________________________ Notes:

Model shown with Flexi-Guard® bubbler.

Spec Seq#: 26

5846

82




• Chrome Plated


1 Wall Tube Brass

2 J-Bend Brass

Model# Options







Box Escutcheon


Shallow Escutcheon



SPECIFICATIONS

1-1/2"(

38.1mm)

8.66"(220mm)3.22"(82mm)

11.89"(302mm)

4.72"(120mm)

1.52"( 38.5mm)

2.95"( 75mm)

1.5"( 38.1mm)

1.42"(36mm)

2.99"( 76mm)

1.5"( 38.1mm)

1.42"(36

mm)

Spec Seq#: 27

8257

62


MLQTR04RX

NSF/ANSI 61

Cross ReferenceReferencias adicionalesRéférences● R04 R ● KTR04 R● KTR04X R

Features / Caractéristiques / Características● Rough Brass● Easy Quarter Turn Operation● Inlet ‐ 1/2” Sweat● Outlet ‐ 1/4” O.D. Comp.● Material: Machined One Piece Brass Body● Lead Free (≤ .25% Pb)

● Laiton brut● Commande quart de tour facile● Entrée ‐ 1/2 po à braser● Sortie – dia. ext. 1/4 po à compression● Matériau : Corps en laiton usiné d’une seule pièce● Sans plomb (≤ .25% Pb)

● Bronce rústico● Funcionamiento fácil, cuarto de vuelta● Entrada – 1/2” con soldadura● Salida – diámetro exterior de 1/4”, a compresión● Material: cuerpo de bronce en una pieza● Sin plomo (≤ .25% Pb)











Spec Seq#: 28

9377

79

Spec Seq#: 29

****************RD-1 ROOF DRAIN

****************


WEIGHTPOUNDS

VOLUMECUBIC FEET

FIGURE NUMBER

LOCATIONF

IGU

RE

NU

MB

ER

DIM

EN

SIO

NS

AR

E S

UB

JEC

T T

O M

AN

UFA

CT

UR

ER

S T

OLE

RA

NC

E A

ND

CH

AN

GE

WIT

HO

UT

NO

TIC

EW

E C

AN

AS

SU

ME

NO

RE

SP

ON

SIB

ILIT

Y F

OR

US

E O

F S

UP

ER

SE

DE

D O

R V

OID

DAT

A

DR

AW

N B

Y:

CH

EC

KE

D B

Y:

AP

PR

OV

ED

BY

:D

ATE

:S

CA

LE:

SIZ

E AD

RA

WIN

G N

UM

BE

R

High Position2 1/4 (57) MIN4 (100) MAX

5 1/4 (135)

Polyethylene Dome

Combined Flashing ClampAnd Gravel Stop

Adjustable Extension Sleeve

Reversible Collar

Underdeck Clamp(When Specified)

Low Position1 1/4 (32) MIN2 1/2 (64) MAX

**5 (125)

GENERAL PURPOSE ROOF DRAINS

ROOF DRAIN WITH ADJUSTABLE EXTENSION

FUNCTION: Used in flat roofs of any construction. The adjustable extension sleeve permits adjustment from aminimum of 1 1/4" (32) to a maximum of 4" (100), easily accommodating up to 2 3/4"(70) of varying insulationthicknesses. The positive threading allows smooth perimeter movement and circumferential support of the top at anyadjusted elevation. Large low profile dome provides sufficient free area for quick drainage of rainwater and protectionagainst debris.

REGULARLY FURNISHED:Duco Cast Iron Body with AdjustableExtension Sleeve, Reversible Collar,Combined Flashing Clamp andGravel Stop, with PolyethyleneDome.

VARIATIONS:

Note: See reverse side for assembly instructions.

Expansion Joint (Specify Fig. 1710)"L" Shaped Underdeck Clamp -CLL Speedi-Set Service Weight 02(50), 03(75) & 04(100)" sizes onlyLXH Speedi-Set Extra Heavy 02(50), 03(75) & 04(100)" sizes onlySecondary Flashing Clamp -C2Sump Receiver -RUnderdeck Clamp -CVandal Proof Dome -USide Outlet Drain (Specify Fig. 1025)T Threaded Outlet

OPTIONAL MATERIALS:Aluminum Dome -ADCast Iron Dome -CIDGalvanized Cast Iron -GRough Bronze Dome -RBD

Free Area102.5 SQ IN(661) SQ CM

A (Pipe Size) = 02(50), 03(75), 04(100), 05(125) or 06(150)

Fig. 1015C . . . . . CAULK OUTLETFig. 1015Y . . . . . NO-HUB OUTLET

*This dimension to internal stop of Speedi-Set Gasket**Same for Caulk, NO-HUBand Speedi-Set, 3 3/4 (95) forThreaded

1015

1015

CM

BV

GD

JD12

-19-

84N

ON

ES

1015

K

*3 3/4(95)

15 1/4 (390) DIA

GasketsA

1 1/8 (29) MIN

G 6-23-94 Revised EMB


recommended deck opening

with suffix -Rless Suffix -R

17 (430) DIA14 (355) DIA

BSBSH 6-12-95 Added Millimeters EMBAMJ

K6-5-06 Revised Dim. TBW

12-15-06 Added Note RN CL

11 (280) DIA

JAY R.SMITH MFG. CO.®


DRIVEN

SMITH®

MEMBER OF:

®

ASPE®

SANITARY


Spec Seq#: 30

8342

77


WEIGHTPOUNDS

VOLUMECUBIC FEET

FIGURE NUMBER

LOCATIONF

IGU

RE

NU

MB

ER

DIM

EN

SIO

NS

AR

E S

UB

JEC

T T

O M

AN

UFA

CT

UR

ER

S T

OLE

RA

NC

E A

ND

CH

AN

GE

WIT

HO

UT

NO

TIC

EW

E C

AN

AS

SU

ME

NO

RE

SP

ON

SIB

ILIT

Y F

OR

US

E O

F S

UP

ER

SE

DE

D O

R V

OID

DAT

A

DR

AW

N B

Y:

CH

EC

KE

D B

Y:

AP

PR

OV

ED

BY

:D

ATE

:S

CA

LE:

SIZ

E AD

RA

WIN

G N

UM

BE

R

1

ADJUSTABLE ROOF DRAINDOME

5/16 (8) -18 X 1 1/4 (32) BOLT (4 REQ'D)(USE PIPE SEALER ON THREADS)

FLASHING CLAMP

ADJUSTABLE SLEEVE

1/4 (6) DIA. O-RING POSITIONED IN GROOVEOF THREADS AT INSIDE DIAMETER OFREVERSIBLE COLLAR.

5/16 (8) -18 X 1 1/2 (38) BOLT (4 REQ'D)

5/16 (8) WASHER-NEOPRENE BACKED(4 REQ'D)

REVERSIBLE COLLAR LOW POSITION MIN 1 1/4 (32) MAX 2 1/2 (64) HIGH POSITION MIN 2 1/4 (57) MAX 4 (100)

NEOPRENE FLAT GASKET

BODY

DRAIN RECEIVER -R(RECOMMENDED OPTION)

UNDERDECK CLAMP -C(RECOMMENDED OPTION)

9

8

7

5

4

3 6

2

Position flat gasket on drain body, align holesin gasket with holes in body.

Determine if reversible collar is to be installedin the low (1 1/4” to 2 1/2”) or high (2 1/4” to 4”)position.

Place reversible collar on body and align holesin collar with holes in gasket and body.

Secure collar to body with 1 1/2" long boltsinsuring neoprene backed washers are installed at proper locations between top of reversible collar and bolt head. Tighten bolts in the followingmanner: 1, 3, 2 & 4. Tighten No. 1 bolt approximatelyone full turn then No. 3, No. 2 and No. 4 (same manner as for No. 1). Continue this method untilreversible ring has been secured evenly all around.

Wipe “O” Ring recess in reversible collar clean.Insert “O” Ring in groove of threads at inside diameterof reversible collar. Lubricate “O” Ring in it’s entirety with the lubricant provided. Lubricate the remainingthreads.

Lubricate liberally the entire lead-in chamferand first 2 threads of the adjustable sleeve.Thread adjustable sleeve into reversible collar and adjust to required height. Do notexceed minimum/maximum adjustment dimensions.

Check bolts a final time to insure tightness.

Run waterproofing membrane over top ofadjustable sleeve to inside of boltcircle.

Install flashing clamp and secure with(4) bolts. Again tighten bolts in the1, 3, 2, 4 manner. (See )

Install Dome

1

2

2a

3

4

5

6

7

8

9

3

1015BSC 6-29-88 Revision EMB SJMD 4-12-93 Submittal Update EMB

1015

BS

EM

BM

CD

TD

6-29

-88

NO

NE

S10

15B

SF


BSBSE

F 12-15-06 Rev. Dwg. RN CL6-14-95 Added Millimeters EMB

JAY R.SMITH MFG. CO.®


DRIVEN

SMITH®

MEMBER OF:

®

ASPE®

SANITARY


Spec Seq#: 30

8342

77

JR SMITH 1620T03-B4-NB-WD02 3 THRD NICBRZ GUTTER DRAIN W/4 DEEP BODY BOT

OUT & LOW DOME W/2" INT WTR DAM

Spec sheet not available

Spec Seq#: 31

1492

354

Spec Seq#: 32

*******************EWH-1 WATER HEATER

**********************

Spec Seq#: 33

1397

253

Spec Seq#: 33

1397

253

Spec Seq#: 34

****************HSK-1 KITCHEN SINK

********************

SL-ADA-17519-A-GR

stainless steel. Interior and top surfaces polished to a non-porous Hand-Blended Just Finish with highlighted bowl rim. Fully coated underside insulated for sound and

radius corners provides greater capacity. Self- rimming top mount Grip-

conformance with ASME A112.19.3/CSA B45.4, Canadian Standards (CSA), Uniform Plumbing Code (UPC) and

.niard 53-J

Spec Seq#: 35

1046

016

Spec Seq#: 36

6695

53

Spec Seq#: 36

6695

53

MLL7 BASKET STRAINER

• Forged Brass Body

• Machine Cut Threads

• Metal Post

• Stainless Steel Basket

• Extra Thick Washer

• Heavy Zinc Locknut

MLL7


1 Stick Post Zinc

2 Basket Stainless Steel

3 Stopper Rubber

4 Body Forged Brass

5 Washer Rubber

6 Gasket Paper

7 Locknut Zinc

8 Washer PE

9 Tailpiece Nut Zinc

CROSS REFERENCE

L7 S14-007

2433PC SS-125

656-003 ZSS250-PC


SPECIFICATIONS


Spec Seq#: 37

8256

78





• Chrome Plated


1 Wall Tube Brass

2 J-Bend Brass

Model# Options







Box Escutcheon


Shallow Escutcheon



SPECIFICATIONS

1-1/2"(

38.1mm)

8.66"(220mm)3.22"(82mm)

11.89"(302mm)

4.72"(120mm)

1.52"( 38.5mm)

2.95"( 75mm)

1.5"( 38.1mm)

1.42"(36mm)

2.99"( 76mm)

1.5"( 38.1mm)

1.42"(36

mm)

Spec Seq#: 38

8257

62



MLQTCS40BCX

NSF/ANSI 61















Spec Seq#: 39

9377

53

LEAD FREE*

LAVATORY CONNECTOR 3/8” Comp. x 1/2” FIP





• IAPMO listed to ASME A112.18.6 and CSA B125.6-2009

• Complies with Lead-Free Plumbing Laws

• *≤ .25% Pb




3 Barb Forged Brass, No Lead

4 Ferrule SS 304



7 Washer NSF compliant EPDM


SPECIFICATIONS

Model # MLB112AF MLB116AF MLB120AF MLB130AF

Length 12" 16" 20" 30"

Spec Seq#: 40

9371

81


Spec Seq#: 41

*************ELEVATOR PUMP

**************

ELV_ P1 R9/8/2014 ©Copyright 2014 Liberty Pumps Inc. All rights reserved. Specifications subject to change without notice.

Pump Specifications

ELV Series Submersible Sump Pump with OilTector Control

ELV250 1/3 hp

ELV280 1/2 hp

ELV290 3/4 hp

Spec Seq#: 42

7390

18


ELV280 Dimensional Data

Spec Seq#: 42

7390

18



Spec Seq#: 42

7390

18



ELV290 SERIES DIMENSIONAL

2011

Spec Seq#: 42

7390

18


ELV-Series Electrical Data

MODEL HP VOLTAGE PHASE FULL LOAD AMPS

LOCKED ROTOR AMPS

THERMAL OVERLOAD

TEMP

STATOR WINDING CLASS

CORD LENGTH

FT DISCHARGE AUTOMATIC

ELV290 3/4 115 1 10.4 24 120˚C/ 248˚F B 25 1 1/2 YES W/

CONTROL

ELV290HV 3/4 208-230 1 5.3 13 105˚C/ 221˚F B 25 1 1/2 YES W/

CONTROL

ELV280 1/2 115 1 8.0 23 105˚C/ 221˚F B 25 1 1/2 YES W/

CONTROL

ELV280HV 1/2 208-230 1 4.0 12.5 105˚C/ 221˚F B 25 1 1/2 YES W/

CONTROL

ELV250 1/3 115 1 5.2 8 105˚C/ 221˚F B 25 1 1/2 YES W/

CONTROL

ELV-Series Technical Data

IMPELLER VORTEX ENGINEERED POLYMER

SOLIDS HANDLING SIZE

ELV250 ½”

ELV280, ELV280HV, ELV290, ELV290HV ¾”

PAINT POWDER COAT

MAX LIQUID TEMP 60˚C/ 140˚F

MAX STATOR TEMP CLASS B 130˚C/ 266˚F

THERMAL OVERLOAD

ELV250, ELV280, ELV280HV, ELV290HV

105˚C/ 221˚F

ELV290 120˚C/ 248˚F

MOTOR HOUSING/ VOLUTE CLASS 25 CAST IRON

SHAFT STAINLESS

HARDWARE STAINLESS

ORINGS BUNA N

SHAFT SEAL

ELV250 ENGINEERED DOUBLE LIP WITH

STAINLESS STEEL SPRINGS

ELV280 & ELV280HV ELV290 & ELV290HV UNITIZED CERAMIC CARBON

ELV250 23 LBS

ELV280, ELV280HV, ELV290, ELV290HV 30 LBS

MIN. SUMP SIZE Ø18” X 30”

Spec Seq#: 42

7390

18


ELV-Series Specifications

1.01 GENERAL:

The contractor shall provide labor, material, equipment, and incidentals required to provide (QTY) centrifugal pumps as

specified herein. The pump models covered in this specification are ELV Series single phase pumps. The pump furnished for this

application shall be model ______________as manufactured by Liberty pumps.

2.01 OPERATING CONDITIONS:

Each submersible pump shall be rated for ____hp, _____ volts, single phase, 60 Hz, & 3450 RPM. The unit shall produce

_____G.P.M. at ______ feet of total dynamic head.

The submersible pump shall be capable of handling water with _____ solid handling capability. The submersible pump shall have

a shut-off head of ____ feet and a maximum flow of _____ GPM @ 5 feet of total dynamic head.

The pump shall be controlled with:

The manual pump is connected to a control which has the ability to prevent oil from being pumped from the vault. This same

control unit will activate an alarm when an oil “film” is detected or when a high water condition exits. The system will continue to

monitor and remove water from the vault even if an oil condition is detected.

3.01 CONSTRUCTION:

Each centrifugal sump pump shall be equal to the Certified ELV-Series pumps as manufactured by Liberty Pumps,

Bergen NY. The castings shall be constructed of class 25 cast iron. The motor housing shall be oil filled to dissipate heat. Air filled

motors shall not be considered equal since they do not properly dissipate heat from the motor. All mating parts shall be machined

and sealed with a Buna-N o-ring. All fasteners exposed to the liquid shall be stainless steel. The motor shall be protected on the

top side with sealed cord entry plate with molded pins to conduct electricity eliminating the ability of water to enter internally

through the cord. The motor shall be protected on the lower side with a unitized ceramic/carbon seal with stainless steel housings

and spring or engineered double lip seal with stainless steel springs. The pump shall be furnished with stainless steel handle.

4.01 ELECTRICAL POWER CORD

The submersible pump shall be supplied with a 25 feet of multiconductor power cord. It shall be cord type YELLOW

UL 16-3 SJEOOW 300V 105°C, capable of continued exposure to the pumped liquid. The power cord shall be sized for the rated

full load amps of the pump in accordance with the National Electric Code. The power cable shall not enter the motor housing

directly but will conduct electricity to the motor by means of a water tight compression fitting cord plate assembly, with molded pins

to conduct electricity. This will eliminate the ability of water to enter internally through the cord, by means of a damaged or wicking

cord.

5.01 MOTORS

Single phase motors shall be oil filled, permanent split capacitor, class B insulated NEMA B design, rated for continuous duty. At

maximum load the winding temperature shall not exceed 130 degrees C unsubmerged. Since air filled motors are not capable of

dissipating heat they shall not be considered equal. The pump motor shall have an integral thermal overload switch in the

windings for protecting the motor. The capacitor circuit shall be mounted internally in the pump.

Spec Seq#: 42

7390

18


6.01 BEARINGS AND SHAFT

An upper sleeve and lower ball bearing shall be required. The lower ball bearing shall be a single ball / race type bearing. Both

bearings shall be permanently lubricated by the oil, which fills the motor housing. The motor shaft shall be made of 300 or 400

series stainless steel.

7.01 SEALS

The pump shall have a unitized carbon / ceramic seal with stainless steel housings and spring, or engineered double lip seal with

stainless steel springs. The motor plate / housing interface shall be sealed with a Buna-N o-ring.

8.01 IMPELLER

The impeller shall be vortex style made of an engineered polymer, with pump out vanes on the back shroud to keep debris away

from the seal area. It shall be threaded to the motor shaft.

9.01 CONTROLS

The control unit has three probes and a float ball switch. The pump will activate when the middle probe contacts water, and will

remain on until the first, longest probe no longer is in contact with water. A high water alarm is activated when third or shortest

probe contacts water. The system will ignore a small film of oil, however larger volumes of oil will be detected when the alarm

probe does not detect water and the float ball activates. The system will continue to operates, removing water not oil from the

vault even when oil has been detected.

10.01 PAINT

The exterior of the casting shall be protected with powder coat paint.

11.01 SUPPORT

The pump shall have cast iron support legs, enabling it to be a free standing unit.

12.01 SERVICEABILITY

Components required for the repair of the pump shall be shipped within a period of 24 hours.

13.01 TESTING

The pump shall have a ground continuity check and the motor chamber shall be Hi-potted to test for electrical integrity, moisture

content and insulation defects. The motor and volute housing shall be pressurized, and an air leak decay test is performed to

ensure integrity of the motor housing. The pump shall be run, voltage current monitored, and the tester checks for noise or other

malfunction.

14.01 QUALITY CONTROL

The pump shall be manufactured in an ISO 9001 certified Facility.

15.01 WARRANTY

Standard limited warranty shall be 3 years.

Spec Seq#: 42

7390

18

Model S-613 Sump Pump Check Valve

• NOTES:• FULL-FLOW DESIGN• CAN BE INSTALLED HORIZONTAL OR VERTICAL• SLIP x SLIP• ABS BODY• DESIGNED FOR LOW PRESSURE SYSTEMS (4.3 PSI - 10 FT. OF HEAD)

NO. PART MATERIAL

1 TOP BODY ABS

2 FLAPPER EPDM RUBBER AND S.S.

3 BOTTOM BODY ABS

4 SCREW CARBON STEEL

5 NUT CARBON STEEL

6 CLAMP S.S. BAND & CARBON STEEL SCREW

7 RUBBER END ADAPTERS THERMOPLASTIC

SIZE

A

B

1-1/4" & 1-1/2"

2.69

4.81

2"

3.13

4.56

1

3

7

2

4

6

5

A

B

Spec Seq#: 43

6405

4

billw

Typewritten Text

billw

Typewritten Text

billw

Typewritten Text

billw

Typewritten Text

*130F max temperature *25psi max pressure

billw

Typewritten Text

billw

Typewritten Text

billw

Typewritten Text

billw

Typewritten Text

NIBCO INC. WORLD HEADQUARTERS • 1516 MIDDLEBURY ST. • ELKHART, IN 46516-4740 • USA • PH: 1.800.234.0227 TECH SERVICES PH: 1.888.446.4226 • FAX: 1.888.336.4226 • INTERNATIONAL OFFICE PH: +1.574.295.3327 • FAX: +1.574.295.3455

www.nibco.com55

www.nibco.com A H E A D O F T H E F L O W® Revised 9/10/2009

UNIV. NOM. APPROX. DIM. A FIG. NO. SIZE NET WT./LBS. INCHES

457-015 11/2 .200 11/16 457-020 2 .500 25/32

4633 Union (Slip x Slip)


450-002 1/4 .007 23/32 450-005 1/2 .020 11/16

450-007 3/4 .030 13/32

450-010 1 .070 11/4

450-012 11/4 .108 11/8

450-015 11/2 .160 125/32

450-020 2 .220 115/16

450-025 21/2 .340 23/32

450-030 3 .495 213/32

450-040 4 .560 213/16

4616-4 Plug (MIPT)


477-005 1/2 .033 1/2

4601-T-D Nested Coupling (Slip x Slip)


478-005 1/2 .030 19/16

478-007 3/4 .043 113/16

478-010 1 .076 21/8

478-020 2 .182 211/32

4603-2 Female Fitting Adapter (Spg x FIPT)

PLUGS (Continued)

UNIONS

NESTED COUPLING

FITTING ADAPTER

PVC Schedule 40 Pressure Fittings

Do not use or test the products in this catalog with compressed air or other gasses.

Spec Seq#: 44

6543

3

55100 INCOMING FREIGHT CHARGES

Spec sheet not available

Spec Seq#: 45

1460

462

Documents

Plumbing Submittal - Hajoca · Plumbing Submittal FAIRLESS CREDIT Submitted by MYSTIC MECH 1/12/2016 ... plomberie sans plomb L’entrée à souder est conforme à la norme ANSI B16.18