SQW0709

Operating Instructions<Full version>

Access Point AdaptorModel No. SH-WL30

Thank you for purchasing Panasonic ALL series product.Please read these instructions carefully before using this product, and save this manual for future use.

Table of contentsFeatures ..................................................................3Unit care ..................................................................4Accessories .............................................................5Control reference guide...........................................6Connections ............................................................8Network settings....................................................10To make network-related settings..........................17Firmware updates..................................................28Troubleshooting.....................................................30Specifications ........................................................33

How to use this manual

Click/Tap this icon to jump to “Table of contents”.

≥Pages to be referred to are indicated as “l ±±”. You can jump to the corresponding page by clicking/tapping this.

- 2 -

FeaturesThis unit allows you to convert the security type of your home Wi-Fi® environment from WPATM to WPA2TM.

WPAWPATMTM

WPA2WPA2TMTM

Broadband router, etc.

This unit

your ALL speakers

PC, smartphone, etc.

- 3 -

Unit careClean this unit with a soft, dry cloth.≥ Never use alcohol, paint thinner or benzine to clean this unit.≥ Before using chemically treated cloth, carefully read the cloth’s instructions.

∫ To dispose or transfer this unitThe unit may keep the user settings information in the unit. If you discard this unit either by disposal or transfer, then follow the procedure to return all the settings to the factory defaults to delete the user settings. (l 30, “To return all settings to the factory defaults.”)≥ The operation history may be recorded in the memory of this unit.

Disposal of Old EquipmentOnly for European Union and countries with recycling systemsThis symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products

must not be mixed with general household waste.For proper treatment, recovery and recycling of old products, please take them to applicable collection points in accordance with your national legislation.By disposing of them correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment.For more information about collection and recycling, please contact your local municipality.Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

- 4 -

AccessoriesCheck the supplied accessories before using this system.

∏ 1 AC adaptor

∏ 1 DC cable

∏ 1 LAN cable

≥ Do not use any other AC adaptors except the supplied one.≥ The supplied DC cable is for use with this system only. Do not use it with other

equipment. Also, do not use cords from other equipment with this system.

- 5 -

Control reference guide

Top

1 Power indicatorLights upThis unit is on.≥ The unit is in the standby

condition when the AC adaptor is connected. The primary circuit is always “live” as long as the AC adaptor is connected to an electrical outlet.

2 5 G indicatorBlinks/Lights upThe 5 GHz band (11n/a) is available.

3 2.4 G indicatorBlinks/Lights upThe 2.4 GHz band (11n/g/b) is available.

4 WPS indicatorBlinksThe WPS feature is enabled.

5 LAN1 indicatorLights upA LAN cable is connected to the LAN1 terminal.

6 LAN2 indicatorLights upA LAN cable is connected to the LAN2 terminal.

- 6 -

≥When this unit is not working correctly, disconnect and reconnect the AC adaptor first. If the problem persists, press and hold the RESET button for at least 5 seconds with a paper clip or similar, and then release the button.

Rear

7 DC IN terminalDC 5 V 1.8 A

8 LAN2 terminal

9 LAN1 terminal

10 RESET buttonResets this unit to the factory default settings.Use a paper clip or similar to press this button when this unit is not working correctly, for example.

11 WPS button

12 QR code

13 Key

13

1213

12

- 7 -

Connections

§ Use this connection to:jconfigure advanced settings for this unit (l 17)jupdate the firmware of this unit (l 28)

≥ The LAN cable must be connected or disconnected while the AC adaptor is disconnected.≥ Inserting any cable other than a LAN cable in the LAN port can damage the

unit.≥ If the LAN cable is disconnected, the network-related settings (l 17) will be

initialized. In that case, make the settings again.

LAN

A LAN cable (supplied)Do not use any other LAN cable except the supplied one.

B Broadband router, etc.

C LAN cable (not supplied)Use category 5 or above straight LAN cables (STP) when connecting to peripheral devices.

D PC

※

※

- 8 -

E DC cable (supplied)Check the directions of the connectors, and plug them straight in or unplug them straight out. (Otherwise the connectors may bend out of shape, which may cause malfunction.)

F AC adaptor (supplied)G To power outlet

The indicators (*) light up in blue after approximately 60 seconds.

≥ For the purpose of power conservation, disconnect the power supply if you will not be using it for extended period of time. Some settings will be lost after you disconnect the system. You have to set them again.

DC

*

- 9 -

Network settingsYou can stream music from a device on the network by using the Qualcomm® AllPlayTM smart media platform or DLNA feature. To use these features, this unit must join the same network as the device.Qualcomm® AllPlayTM smart media platform is a product of Qualcomm Connected Experiences, Inc.Choose a network setting method from the following.

≥ The setting will be cancelled after the set time limit. In that case, try the setting again.

“Using an Internet browser” (l 13)≥You can access this unit’s network settings from the Internet

browser on your smartphone or tablet, etc.

“Using WPS (Wi-Fi Protected SetupTM)” (l 16)≥You can connect to a wireless LAN network by pressing the WPS

button or entering a PIN code.

“Using the app “Panasonic Music Streaming”” (l 11)≥You can make the wireless network settings with the app,

“Panasonic Music Streaming” (free of charge).

- 10 -

≥Do not connect a LAN cable to ALL speaker. Doing so will disable the Wi-Fi function.

1 Download and start the app “Panasonic Music Streaming” (free of charge) on your smartphone.≥ [iOS] : App Store≥ [Android] : Google PlayTM

2 Open the app and follow the on-screen instructions.≥ Follow the app’s instructions to connect to your ALL speaker.

The procedure splits into the paths described below along the way.∫Path 1: When the SH-WL30 is detected

(a screen similar the one below appears)

1Select “Add”.2Scan the QR code on the bottom side of this unit.

Scan the QR code for either 5 GHz (recommended) or 2.4 GHz, depending on your environment. (l 27)

Using the app “Panasonic Music Streaming”

- 11 -

∫Path 2: When the SH-WL30 is not detected automatically (a screen similar the one below appears)

≥ Depending on the screen size of your smartphone/tablet, you may need to scroll to the bottom for any remaining steps.

Refer to “Using an Internet browser” (l 13).Configure the connection of the ALL speaker to be added to the wireless network.For details, refer to the Operating Instructions for the ALL speaker.≥ In case you are not connected automatically,

please re-select your Wi-Fi network from the settings / Wi-Fi settings menu on your device.

The operations and on-screen display items, etc. of the app “Panasonic Music Streaming” are subject to change.For the latest information, visit

http://panasonic.jp/support/global/cs/audio/app/(This site is in English only.)

- 12 -

≥The following steps are based on a smartphone.

1 Turn on your ALL speaker.≥ You may need to configure the ALL speaker manually.

For details, refer to the Operating Instructions for the ALL speaker.

2 Go to Wi-Fi settings on the device.

3 Select “AllPlay_AJ” to connect to this unit.≥ “” stands for a character that is unique to each set.≥ This can take up to 1 minute to appear in your Wi-Fi list.≥ If this operation does not work correctly, please repeat it several times.≥Make sure that DHCP is enabled for the network setting on your compatible

device.

[iOS_device]: The settings page will be automatically displayed in the Internet browser.[Except_iOS_device]: Open the Internet browser and refresh the page to display the settings page.≥ If the settings page is not displayed, input “http://172.19.42.1/” into the URL

address field.

Using an Internet browser

Settings Wi-Fi Settings

Wi-Fi AllPlay

- 13 -

4 Input a device name and then select “Next”.≥ The device name will be displayed as this unit’s name on the network.≥ The guaranteed limit is 32 characters.≥ The device name is set when “Next” is selected.≥ You can also change the device name after the network connection is set

up. (l 17)

5 Change the network name (SSID) to “SH-WL30-5G-” or “SH-WL30-2G-”and input the password (Key) for this unit (refer to the bottom side of the unit).

≥ Check the wireless router for the network name (SSID) and the password.≥ A list of network names (SSIDs) will be appeared when you select the

“Network Name” field.≥ To show the characters typed in the “Password” field, select “Show

Password”.≥ If your network requires specific settings, deselect “DHCP” to disable

DHCP.– You can use specific IP address, subnet mask, default gateway, primary

DNS, etc.≥ To update the network name (SSID) list, select “Refresh list”.

- 14 -

6 Select “Connect” to apply the settings.≥ Refer to the Operating Instructions for your ALL speaker for information on

how it operates when the connection is complete.≥ Depending on the device, the connection complete screen may not be

displayed.

7 Make sure to connect your compatible device back to your home wireless network.

≥ Enable Java and cookies in your browser settings.≥ You can change the user name and password. (l 26, “Password”)

If the network indicator does not light up, check the network name (SSID) and the password, and then try the setting again.

- 15 -

≥Do not connect a LAN cable to ALL speaker. Doing so will disable the Wi-Fi function.

1 Set your ALL speaker to WPS Connection mode.≥ For details, refer to the Operating Instructions for the ALL speaker.

2 Press and hold the WPS button on this unit for at least 3 seconds.

≥ The WPS indicator blinks. The WPS indicator blinks for about 2 minutes until the connection is completed.≥When the connection is complete, the WPS indicator will light up for about

10 seconds.

≥ The default setting is 5 GHz.Go to the advanced setup screen to switch to 2.4 GHz. (l 27)≥ The WPS indicator blinks fast for about 1 minute when a connection attempt

fails.

Using WPS (Wi-Fi Protected SetupTM)

- 16 -

To make network-related settingsYou can change this unit’s name on the network, and use specific IP address, etc.

Preparation≥Change the IP address settings of the device (PC, etc.) to the ones

below.For details on how to change these settings, refer to the operating instructions for your device.IP Address:“10.10.10.” (“” stands for any number between 1 and 253.)Subnet mask:“255.255.255.0”≥Connect this unit and the device. (l 8)

1 Start an Internet browser on your device and then input “http://10.10.10.254/” into the address field to display the settings page.

2 Input user name and password and select “OK”.≥When performing this step for the first time, enter “admin” into both the ID

and password fields.≥ It may take a few minutes until the settings page is displayed depending on

the environment. In that case, reload the browser.≥ If you enter a wrong ID or password, close the Internet browser first, and

then follow the steps above again.

You can also change the name of this unit by changing a setting in the app “Panasonic Music Streaming” (version 3.1.0 or later) (l 11). For details on the app, refer to the site below.http://panasonic.jp/support/global/cs/audio/app/(This site is in English only.)

Select Englishor French.

- 17 -

Select either “2.4G” or “5G”.Basic SettingsThis page is used to configure the parameters for wireless LAN clients that may connect to this unit. Here you may change wireless relative settings as well as wireless network parameters.When the settings are complete, click “Apply”.≥The settings will be applied after you click “Refresh” and wait for a while.≥To reconfigure the settings, click “Back”.

Wireless

Item Description

WiFi UP/DOWNThe setting changes each time you click the item.You can turn on/off the 2.4 GHz or 5 GHz radio signal setting.

Network Mode You can select the setting from the pull down menu.

1st SSID It is the wireless network name. The SSID can be 32 bytes long.

Channel Width You can select the setting from the pull down menu.

Channel NumberYou can select the setting from the pull down menu.Select the wireless communication channel from the pull-down menu.

SSID stealth You can select the setting from the pull down menu.

- 18 -

EncryptionThis page allows you setup the wireless security. Turn on WPA2 by using encryption keys could prevent any unauthorized access to your wireless network.When the settings are complete, click “Apply”.≥The settings will be applied after you click “Refresh” and wait for a while.≥To reconfigure the settings, click “Back”.

Item DescriptionSelect SSID The SSID of this unit is displayed.

EncryptionSelect the encryption supported over wireless access from the pull down menu.

Key Format

Select the WEP shared secret key format from the pull-down menu. The format can be chose between Passphrase and hexadecimal (HEX) code.

Pre-Shared Key Secret key of WEP security encryption function.

Show Password Click checkbox to show/hide password.

- 19 -

Access ControlIf you enable wireless access control, only those clients whose wireless MAC addresses are in the access control list will be able to connect to this unit.When this option is enabled, no wireless clients will be able to connect if the list contains no entries.

When the settings are complete, click “Apply”.≥The settings will be applied after you click “Refresh” and wait for a while.≥To reconfigure the settings, click “Back”.

Item Description

Wireless Access Control Mode

Select the Wireless Access Control mode setting from the pull down menu.This is a security control function; only those clients registered in the access control list can link to this unit.

MAC Address Input the MAC address of client to register this unit access capability.

Comment Input the comment tag for the registered client.

Current Access Control List It shows the registered clients that are allowed to link to this unit.

DelClick to delete the selected clients that will be access right removed from this unit.

Delete All Click to delete all the registered clients from the access allowed list.

- 20 -

WPSThis page allows you to change the setting for WPS (Wi-Fi Protected Setup).Using this feature could let your wireless client automically syncronize its setting and connect to the access point in a minute without any hassle.When the settings are complete, click “Start”.≥The settings will be applied after you click “OK” and wait for a while.

Item Description

PIN code of this device PIN code of access point created while manufacturing

PBC method connection

The Start button provides tool to scan the wireless network. If any access point or independent basic service set is found, you could connect it automatically when client join PBC mode.

PIN code of client Input the Client PIN Number from your Client sites.

- 21 -

LAN InterfaceThis page is used to configure the parameters for local area network that connects to the LAN ports of this unit. Here you may change the setting for IP address.When the settings are complete, click “Apply”.≥The settings will be applied after you click “Refresh” and wait for a while.≥To reconfigure the settings, click “Back”.

≥ If you change the IP address, make a note of the new address.≥ If you forget the new IP address, initialize this unit. (l 26)

TCP/IP Settings

Item Description

IP Address Input the IP address of LAN interfaces of this unit.

- 22 -

StatusThis page shows the current status and some basic settings of the device, includes system, wireless, Ethernet LAN and WAN configuration information.

System

LAN configuration

Management

Item Description

Uptime It shows the duration since this unit is powered on.

Firmware Version It shows the firmware version of this unit.

Operation Mode It shows the current mode setting.

Item Description

IP Address It shows the IP address of LAN interface of this unit.

Subnet Mask It shows the IP subnet mask of LAN interface of this unit.

DHCP Server It shows the DHCP Server status.

MAC Address It shows the MAC address of LAN interface of this unit.

- 23 -

Wireless 2.4G ConfigurationWireless 5G ConfigurationItem Description

SSID

It shows the SSID of this unit.The SSID is the unique name of this unit and shared among its service area, so all devices attempts to join the same wireless network can identify it.

Channel Number It shows the wireless channel connected currently.

Encryption It shows the status of encryption function.

BSSID It shows the BSSID address of this unit. BSSID is a six-byte address.

Associated Clients It shows the number of connected clients (or stations, PCs).

- 24 -

Upgrade Firmware (l 28)This page allows you upgrade the firmware to new version.

Select the firmware file, and click “Upgrade”.

Please note, do not turn off the unit during the upgrade because it may crash the system.

Item DescriptionFirmware Version It show the current firmware version.

Select File Click the Browse button to select the new version of firmware file.

- 25 -

ResetClick “Reset” to restore the factory default settings.≥The settings will be applied after you click “OK” and wait for a while.

PasswordWhen the settings are complete, click “Apply”.≥A login screen is displayed. Enter a new “User Name” and “Password”.

Item Description

User NameInput a user name used for authentication. (maximum 30 characters)

New Password Input a new password.(maximum 30 characters)

Confirmed Password Input the new password again for confirmation.

- 26 -

WPS SettingWhen the settings are complete, click “Apply”.This page allows you set physical WPS button connect to 2.4 G or 5 G band.

∫Characteristics of radio wave frequency bands5 GHz frequency band≥Normally not used by devices other than routers. As a result, it provides

very reliable connections and stable performance.≥Offers faster communication speeds than the 2.4 GHz band.≥More sensitive to obstacles such as walls and floors than the 2.4 GHz

band. Radio waves become weaker over longer communication distances.≥Older Wi-Fi devices may not support the 5 GHz band.

2.4 GHz frequency band≥Offers superior penetration of obstacles such as walls and floors,

allowing radio waves to travel longer distances.≥Supported by most Wi-Fi devices.≥Prone to congestion and unstable performance because it is used by a

wide variety of products. (In an apartment or condominium building, for example, you may also experience radio wave interference from devices in other rooms.)

- 27 -

Firmware updatesPanasonic may release updated software for this unit that may add or improve the way a feature operates. These updates are available free of charge.

Preparation≥Change the IP address settings of the device that you are going to use

for an update (PC, etc.) to the ones below.For details on how to change these settings, refer to the operating instructions of your device.IP address:“10.10.10.” (“” stands for any number between 1 and 253.)Subnet mask:“255.255.255.0”≥Connect this unit and the device. (l 8)

1 Download the update file to your device.For more details, refer to the following website.http://av.jpn.support.panasonic.com/support/global/cs/audio/download(This site is in English only.)Example: Save the file to the desktop of your computer.

2 Decompress the file.≥ Check that the file name is “V6OA-.frm” (“” stands for a character that

is unique to each set).3 Start an Internet browser on your device and then input “http://

10.10.10.254/” into the address field to display the settings page. ≥ If you changed the IP address in “TCP/IP Settings”, enter the new address.

(l 22)

For details on the app, refer to the site below.http://panasonic.jp/support/global/cs/audio/app/(This site is in English only.)

DO NOT DISCONNECT the AC adaptor or LAN cable during the update.

≥ During the update process, no other operations can be performed.

- 28 -

4 Input user name and password and select “OK”.≥ For the first time, input “admin” into the ID and password field.≥ It may take a few minutes until the settings page is displayed depending on

the environment. In that case, reload the browser.

5 Select “Management”, and then “Upgrade Firmware”.

6 Select a file in “Select File”.≥ Select “V6OA-.frm” (“” stands for a character that is unique to each

set).

7 Select “Upgrade”.≥ After the firmware is installed, the following screen will be displayed.

8 After clicking “Reset” (l 26), disconnect the AC adaptor.≥ You can also use the RESET button on the rear of this unit to reset it. (l 7)

9 After 30 seconds, reconnect the AC adaptor.

≥ Downloading will require several minutes. It may take longer or may not work properly depending on the connection environment.≥ To show the firmware version on this unit. (l 23, “Firmware Version”)

Please note, do not turn off the unit during the upload because it may crash the system.

- 29 -

TroubleshootingBefore requesting service, make the following checks.If the problem remains unresolved, consult your dealer for instructions.

For further dedicated help, support and advice about your ALL Series product please visit: http://panasonic.jp/support/global/cs/audio/ALL/(This site is in English only.)

To return all settings to the factory defaults.≥Press and hold the RESET button for at least 5 seconds with a paper

clip or similar, and then release the button.

Cannot turn on the unit.≥After connecting the AC adaptor, wait about 10 seconds.≥Check to see if the USB connector of the DC cable is correctly

connected to the AC adaptor. (l 9)≥Check to see if the DC cable is correctly connected to this unit. (l 9)

The indicators do not light up.≥Check to see if the USB connector of the DC cable is correctly

connected to the AC adaptor. (l 9)≥Check to see if the DC cable is correctly connected to this unit. (l 9)≥The WPS indicator blinks/lights up only when the WPS feature is in use.≥The LAN1 or LAN2 indicator lights up only when this unit is correctly

connected to another device with a LAN cable.

Do you have the latest firmware installed?≥Panasonic is constantly improving the unit’s firmware to ensure that

our customers are enjoying the latest technology. (l 28)

- 30 -

Cannot connect to the ALL speaker.≥Check that this unit is on.≥Check that the ALL speaker is on. For details, refer to the Operating

Instructions for the ALL speaker.≥Check to see if this unit is correctly connected to the router with the

supplied LAN cable.≥Check that the router connected to this unit is on.≥Refer to “Network settings” to reconnect to the ALL speaker.

(Try a different connection method.) (l 10)≥Change the frequency setting to 5 GHz or 2.4 GHz, and reconnect to the

ALL speaker.

The speaker is frequently disconnected.≥ Is this unit or the Wi-Fi router placed on the floor?

The radio signal condition is poor in locations close to the floor. Place them on a desk or similar object so that they are about 1 m above the floor. ≥When you are using multiple ALL speakers and some of them are not

displayed sometimes, we recommend placing the Wi-Fi router at the centre of your house so that all the speakers will be at an equal distance from the router.≥Turn on and off the router.

Another router nearby may be using the same channel, causing interference.≥We recommend that you reset the router by turning it off and on.

If you have multiple routers, reset each of them one by one, rather than at once.≥Are there any obstacles near this unit or the router?

Avoid placing objects near the ALL speaker so that it can receive radio signals.≥ Is there a dishwasher or microwave near this unit or the router?

Devices with motors (dishwashers, etc.) and devices that emit radio signals may cause radio signal interference. Leave at least about 10 cm of space on all sides of the router and ALL speaker. In addition to metal objects, walls adversely affect the antenna performance.

- 31 -

≥ Is the channel fixed to a particular setting by the Wi-Fi router? We recommend that you set the channel to AUTO.≥ Is the maximum communication speed limited to a particular setting by

the Wi-Fi router? If this is the case, it may not achieve optimal performance.≥ Is there a cordless phone near this unit or the router?

When placing this unit near a device that emits radio signals, leave at least 1 m distance from the device.

Cannot display the web setup screen.≥Check to see if this unit and PC are connected correctly. (l 8)≥The PC and this unit must be on the same network.

Change the IP address of the PC so that the devices are on the same network. (l 17)≥The screen is not accessible when this unit has just been turned on.

Wait for some time and start up the browser again.

Cannot login to the web setup screen.≥Check the user name and password.≥Check to see if you have correctly entered upper and lower case

characters.≥Reset this unit to the factory default settings. (l 30)

Cannot update the firmware.≥Check to see if the file has been downloaded correctly from the support

site.≥Perform automatic decompression of the downloaded file, and check

that the file name is “V6OA-.frm” (“” stands for a character that is unique to each set).≥Download the file from the support site again to perform an update.

- 32 -

Specifications∫Wi-Fi SECTION

∫ TERMINALS SECTION

∫ACCESSORIES SECTION

∫GENERAL

≥ Specifications are subject to change without notice.*1 When LAN cables are not connected.*2 When LAN cables are connected to the LAN1 and LAN2 terminals and this

unit is connected to a Wi-Fi network.

WLAN Standard IEEE802.11a/b/g/nFrequency range 2.4 GHz band (1 to 11 ch)

5 GHz band (36 ch, 40 ch, 44 ch, 48 ch)Security WPA2TM

WPA2TM/WPATM mixedmodeWPS version Version 2.0

LAN port 210 Base-T/100 Base-TX

DC IN 5 V 1.8 A

AC Adaptor AC 110 V to 240 V, 50 Hz/60 Hz, 0.25 ADC Cable 1.2 m (USB A to DC plug)LAN Cable 1 m (Straight/Category 5)

Power consumption Approx. 3.8 WPower consumption*1 Approx. 2.0 WPower consumption*2 Approx. 2.3 WDimensions (WkHkD) 100.0 mmk23.0 mmk67.2 mmMass Approx. 81.0 gOperating temperature range 0 oC to r40 oCOperating humidity range 10 % to 80 % RH

(no condensation)

- 33 -

Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States, and other countries and used with permission.AllPlay is a trademark of Qualcomm Connected Experiences, Inc., and used with permission.

The Wi-Fi CERTIFIEDTM Logo is a certification mark of Wi-Fi Alliance®. The Wi-Fi Protected SetupTM Identifier mark is a certification mark of Wi-Fi Alliance®. “Wi-Fi®” is a registered trademark of Wi-Fi Alliance®. “Wi-Fi Protected SetupTM”, “WPATM”, and “WPA2TM” are trademarks of Wi-Fi Alliance®.DLNA, the DLNA Logo and DLNA CERTIFIED are trademarks, service marks, or certification marks of the Digital Living Network Alliance.Google Play and Android are trademarks of Google Inc.App Store is a service mark of Apple Inc.All other trademarks are trademarks of their respective owners.

Declaration of Conformity (DoC)Hereby, “Panasonic Corporation” declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.Customers can download a copy of the original DoC to our R&TTE products from our DoC server:http://www.doc.panasonic.deContact to Authorised Representative:Panasonic Marketing Europe GmbH, Panasonic Testing Centre, Winsbergring 11, 22525 Hamburg, GermanyThis product is in compliance with the radio standards of the following countries.GB, DE, AT, BE, DK, SE, FR, IT, ES, NL, FI, GR, PT, PL, HU, CZ, SK, EE, LV, LT, SI, BG, RO, MT, CY, IE, LU, HR, NO, CH, IS, LIThe WLAN feature of this product shall exclusively be used inside buildings.This product on purpose to connect to access point of 2.4 GHz or 5 GHz WLAN.

Class II equipment (The construction of the product is double-insulated.)QR Code is a registered trademark of DENSO WAVE INCORPORATED.

- 34 -

Manufactured by: Panasonic CorporationKadoma, Osaka, Japan

Importer for Europe: Panasonic Marketing Europe GmbHPanasonic Testing CentreWinsbergring 11, 22525 Hamburg, Germany

Panasonic Corporation

Web Site: http://www.panasonic.com

C Panasonic Corporation 2016

pSQW0709

F0316SB0