Operating and installation instructions for condenser ... · workwear. Such clothing may require a heavy duty detergent to get them clean. If necessary consult the detergent manufacturer

Operating and installation instructionsfor condenser tumble dryerPT 7135 C

To avoid the risk of accidents ordamage to the machine it isessential to read these instructionsbefore it is installed, commissioned andused for the first time.

G

M.-Nr. 06 511 380

Disposal of the packingmaterialThe transport and protective packinghas been selected from materials whichare environmentally friendly for disposaland can normally be recycled.

Ensure that any plastic wrappings,bags etc. are disposed of safely andkept out of the reach of babies andyoung children. Danger of suffocation!

Rather than just throwing thesematerials away, please ensure that theyare offered for recycling.

Disposal of your old machineElectrical and electronic machinesoften contain materials which if handledor disposed of incorrectly, could bepotentially hazardous to human healthand to the environment. They are,however, essential for the correctfunctioning of your machine. Please donot therefore dispose of it with yourhousehold waste.

Please dispose of it at your localcommunity waste collection / recyclingcentre and ensure that it presents nodanger to children while being storedfor disposal.

It should be unplugged ordisconnected from the mains electricity

supply by a competent person. Theplug must be rendered useless and thecable cut off directly behind it toprevent misuse. See the "Warning andSafety" section of this booklet for furtherdetails.

Energy saving tipsTo avoid unnecessarily long dryingtimes and high consumption of energy:

– Make sure that your laundry isthoroughly spun before drying.The higher the spin, the greater thesavings that can be made in energyand time during drying.

– Load according to the optimumamount of laundry recommended forthe programme being used.Underloading is uneconomical.Overloading gives a poorer quality ofdrying and may cause unnecessarycreasing.

– Make sure the room in which thedryer is located is well ventilated.

– After every cycle remove the flufffrom the fluff filter in the door and inthe door opening (see "Cleaning andCare").

– Check the condenser unit from timeto time and clean it when necessary.

Caring for the environment

2

Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Disposal of the packing material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Disposal of your old machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Energy saving tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Operating the tumble dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Before using for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Notes on laundry care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Care symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Tips on drying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

How to dry correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Brief instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Favourite programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Selecting/changing a favourite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Low temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Saving a favourite programme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Programme chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Changing the programme sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Payment system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Cancelling a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Adding or removing laundry after a programme has started . . . . . . . . . . . . . . . . 25

Contents

3

Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Cleaning the fluff filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Cleaning them whilst dry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Cleaning them with water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Replacing the filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Cleaning the tumble dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Cleaning the heat exchanger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Removing the heat exchanger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Checking the heat exchanger unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Cleaning the heat exchanger unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Replacing the heat exchanger unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Problem solving guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Fault messages in the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Other problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Changing the lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38PC / Optical interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Installation and connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39View from the front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39View from the side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40View from the rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40View from above . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Washer-dryer stack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Installation on a concrete plinth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41Payment system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Transporting the machine to its installation site . . . . . . . . . . . . . . . . . . . . . . . . 42Levelling the machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Room in which the dryer is located . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

External drainage of the condensed water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Electrical connection U.K. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Contents

4

Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Settings menu J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Language J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Anti-crease action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Time of day . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Display contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Display brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Extending the cooling down time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Settings/Supervisor level menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Contents

5

To avoid the risk of accidents anddamage to the machine please readthese instructions carefully beforeusing it for the first time. They containimportant information on its safety,installation, use and maintenance.Keep these instructions in a safeplace and ensure that new users arefamiliar with the content. Pass them onto any future owner of the machine.

Correct useThe tumble dryer is only intendedfor drying fabrics which have been

washed in a water solution, marked onthe manufacturer's care label as beingsuitable for tumble drying."Dry cleaning kits" for freshening upgarments in a tumble dryer areincreasingly available on the market. Ifusing, do so at your own risk, andfollow the instructions provided on thepackaging.Any other applications may bedangerous. The manufacturer is notliable for damage resulting fromimproper use or operation.

Technical safetyBefore setting up the machine,check it for any externally visible

damage.Do not install or use a damagedmachine.

Before connecting the machine,ensure that the connection data on

the data plate (voltage and connectedload) match the mains electricitysupply. If in any doubt, consult aqualified electrician.

The electrical safety of this machinecan only be guaranteed when

continuity is complete between it and aneffective earthing system which complieswith local and national regulations. It ismost important that this basic safetyrequirement is present and regularlytested, and where there is any doubt theon-site wiring system should beinspected by a qualified electrician. Themanufacturer cannot be held liable forthe consequences of an inadequateearthing system (e.g. electric shock).

Do not connect the machine to themains electricity supply by an

extension lead. Extension leads do notguarantee the required safety of themachine (e.g. danger of overheating).

The machine is built in accordancewith current safety requirements.

Unauthorised repairs could result inunforeseen dangers for the user, for whichthe manufacturer cannot accept liability.Repairs should only be undertaken by aMiele approved technician.Ensure current is not supplied to themachine until after maintenance or repairwork has been carried out.

Faulty components must only bereplaced by genuine Miele original

spare parts. Only when these parts arefitted can the safety standards of themachine be guaranteed.

In countries where there are areaswhich may be subject to infestation

by cockroaches or other vermin, payparticular attention to keeping themachine and its surroundings in aclean condition at all times. Anydamage which may be caused bycockroaches or other vermin will not becovered by the machine guarantee.

Warning and Safety instructions

6

If the connection cable is faulty itmust only be replaced with a

genuine Miele connection cable.

In the event of a fault or forcleaning purposes, the machine is

only completely isolated from theelectricity supply when:

– it is switched off at the wall socketand the plug is withdrawn, or

– it is switched off at the mains, or

– the mains fuse is withdrawn.

OperationThis equipment may only be usedin mobile installations such as

ships, caravans, aircraft etc. if a riskassessment of the installation has beencarried out by a suitably qualifiedengineer.

The dryer must not be used withoutthe condenser unit in place.

The dryer must not be used withoutthe fluff filters in place or if the fluff

filters are damaged in any way.

The fluff filters must be thoroughlydried after cleaning. If they are

damp or wet when replaced there is arisk of faults occurring when themachine is used.

If the water is drained externallythrough the drain hose instead of

being collected in the condensed watercontainer, make sure the drain hose issecurely attached if you hang it in asink or basin to avoid the hose slippingthe water causing damage.

Condensed water is not drinkingwater. It can cause health

problems in both people and animals.


7

Always keep the area around themachine free of dust and fluff. Dust

drawn into the machine can over timecause blockages in the condenser unit.

Do not install the machine in aroom where there is a risk of frost

occurring. At temperatures aroundfreezing point the machine may not beable to operate properly.There is a risk of damage if thecondensed water is allowed to freeze inthe pump, hoses and / or condensedwater container.The ambient room temperature shouldbe between +2°C and +35°C.

To prevent the risk of fire thefollowing textiles must not be

dried in this machine:

– fabrics which contain a largeproportion of rubber, foam rubber orrubber like materials.

– items which contain padding orfillings (e.g. pillows, jackets).

– items which have been treated withinflammable cleaning agents.

– items which have been splashed withhair lacquer, hair spray, nail varnishremover or similar substances.

– items which have been soiled withoils or residues containing grease(kitchen oils, cosmetics etc.).

– items soiled with wax or otherchemicals (e.g. mops and floorcloths).

– items which have not beenthoroughly cleaned and which arestill soiled with grease or oil, e.g.workwear. Such clothing may requirea heavy duty detergent to get themclean. If necessary consult thedetergent manufacturer for advice.

Do not let anyone sit or lean on thedoor, as this can cause the

machine to tip up.

Always close the door after use.This way you will avoid the danger

of:

– children climbing onto or into thedryer or hiding things in it.

– pets or other small animals climbinginto it.


8

For machines with stainless steelsurfaces:

The stainless steel surfaces must notcome into contact with liquid cleaningand disinfecting agents which containchlorine or sodium hypochlorite. Theseagents can have a corrosive effect onstainless steel.

Aggressive vapours containing chlorinecan also be corrosive.Do not store containers of these agentsnear the machine.

Safety with childrenThis machine is not a toy! To avoidthe risk of injury do not allow

children to play on or near it or to playwith the controls. Supervise its use bythe elderly or infirm, and supervisechildren whilst you are operating themachine.

Using accessoriesAccessory parts may only be fittedwhen expressly approved by Miele.

If other parts are used, guarantee,performance and product liabilityclaims may be invalidated.

Disposal of your old machine^ Before discarding an old machine,

disconnect it from the mains supply,or switch off at the wall socket andunplug it.

^ To prevent the risk of misuse, renderany plug useless and cut off thecable directly behind the machine.Make the door lock unusable.

This should be done by a competentperson.

^ The manufacturer cannot be heldliable for damage caused bynon-compliance with these Warningand Safety instructions.


9

Control panel

a Display

See the following pages for more information.

b Start button

c PC / Optical interface

This is used by service technicians to run diagnostic checks on your machineand can also be used to update programming data in the future.

d Multi-function selector

This is used to select menu options (by turning it) and to confirm your selection(by pressing it).

e a button

Opens the door.

Operating the tumble dryer

10

DisplaysEntry menu

1 Cottons Programme selection ...

2 Minimum iron Settings F ...

3 Woollens handcare

4 Smoothing 10:00

When the machine is switched on, the entry menu with 4favourite programmes (factory default settings which can bechanged) will appear with Programme selection highlighted.

Multi-function selector

Turning the multi-function selector moves the highlighting tothe next option.

Pressing the multi-function selector selects the highlightedoption.

Programme selection

There are two ways of selecting a programme:

Option 1:

– Select the Programme selection menu in the display andconfirm your selection by pressing the multi-functionselector.

Option 2:

– Select one of the four programmes on the left hand side ofthe display. These are favourite programmes which youcan set to suit your individual requirements or replace withother programmes of your choice (see "Favouriteprogrammes" for more details).


11

Programme selection menu

Programme Back A

selection Cottons

Minimum iron

Woollens handcare H

^ By turning the multi-function selector you can select anyprogramme. The highlighting will move up or downdepending on the direction the multi-function selector isturned in.

The V H arrows on the right of the display indicate thedirection and further options.

^ Pressing the multi-function selector takes you to the mainmenu of the drying programme selected.

Drying programme main menu

Cottons Normal

Duration: 1:16 h

Low temp.H

Timer YH

Save

H

Back AH

^ Turn the multi-function selector to highlight either the"Drying level" or the "Programme".

– Everything in the display (including Low temp., Timer,Save, Back) can be highlighted and then confirmed bypressing the multi-function selector.

Settings menu J

The Settings menu J is used to alter the tumble dryer'selectronics to suit different requirements.


12

Before using the machine for the first time ensure that it iscorrectly installed and connected. See "Installation andconnection".

Welcome screen

When the tumble dryer is switched on for the first time, thewelcome screen will appear.

The welcome screen will not appear again once aprogramme lasting longer than 1 hour has beencompleted.

After a few seconds the display will change to the screen forsetting the language.

Language J

^ Select the language you want and confirm your selection.

Setting the time of day

^ Set the hour with the multi-function selector and confirmthis setting. Then set the minutes. Confirm the selectionagain to save the time of day in memory.

Before using for the first time

13

Care symbolsBefore drying check the drying symbolon the care label. If there are nosymbols, dry at your own risk!

q . . . . . . . . . Dry at normal temperaturer . . . . . . . . . . Dry at a low temperatures . . . . . . . . . . . . . . . Do not tumble dry

Tips on dryingAlways observe the maximumrecommended loads given in the"Programme chart". Never overload thedrum.

Overloading can cause unnecessarywear and tear to the laundry, give adisappointing drying result andcause more creasing.

– Do not put soaking wet items into thetumble dryer. Spin them thoroughlyafter washing using the appropriatespin speed.

– For delicates and fabrics with thefollowing care label r select Lowtemperature.

– Open jackets so that they can dryevenly.

– Woollens and wool blends tend tobecome matted and shrink if dried ina tumble dryer. They can, however,be "fluffed up" using the Woollenshandcare programme.

– Down-filled garments have liningswhich have a tendency to shrink,depending on the quality of the item.They can be partially dried using theSmoothing programme.

– Pure linen should only be machinedried if specified as suitable by themanufacturer on the care label, asthe surface of the fabric mayotherwise become rough. They canbe partially dried using theSmoothing programme.

– Loopknit garments (e.g. T-shirts andunderwear) tend to shrink dependingon their quality. Do not over-dry thesetextiles. When purchasing thesegarments it is advisable to take theirshrinkage properties into account.

– Minimum iron fabrics and 100%cotton shirts or blouses tend tocrease more, the larger the load,particularly when the weave of thefabric is very fine.Reduce the load or use the Shirtsprogramme.

– Starched laundry can be dried in thetumble dryer. To achieve the usualfinish, double the amount of starchshould be used.

– New dark coloured garments shouldbe washed and dried separatelyfrom light coloured garments to avoidthe danger of colours running anddiscolouring other garments or evenplastic components in the machine.Dark coloured fibres can also settleon light coloured garments and viceversa.

Notes on laundry care

14

Brief instructionsThe headings numbered (A, B, C ...)show the operating sequence and canbe used as a brief guide to using yourmachine.

A Sort the laundry

To ensure an even drying resultseparate out the washed laundry andsort it according to:. . . the drying level required. . . the type of fibre or weave. . . size. . . the moisture content after spinning.

,Make sure that objects e.g.detergent dispensing balls havebeen removed from the laundry.They could melt, and cause damageto the dryer or the laundry.

– Check seams and stitching to ensurethat padding and linings are intact.

– Fasten duvet covers and pillowcases to prevent small items frombeing trapped inside them.

– Fasten zips, hooks and eyes etc.

– Tie fabric belts and apron strings.

– Sew in or remove underwiring frombras.

B Load the tumble dryer

^ Press the a button to open the door.

^ Load the laundry loosely into thedrum.

Do not overload the drum. See the"Programme chart" forrecommended loads for eachprogramme.Overloading can cause unnecessarywear and tear to the laundry andgive a disappointing drying result.

Check the laundry is right inside thedrum so that it cannot get trapped ordamaged when the door is shut.

^ Shut the door either with a gentleswing, or lean against it and push itshut.

How to dry correctly

15

C Select a programme

You can select a programme either by:

– selecting a favourite programme, or

– by going into the Programmeselection menu.

^ If required, you can then select Lowtemperature and/or the Timer (Delaystart time) from the relevantsub-menu.

Please note that the programmeduration shown in the display may varyaccording to the programme selected(see "Estimated time remaining").

The Start button will flash as soon as aprogramme can be started.

Payment systems

If your machine has a payment system,the amount of credit required willappear in the display.

Credit will be lost if the door isopened or the programme cancelledafter it has started.

D Start the programme

^ Press the Start button.

The Start button will light up.

– Programme start will appear in thedisplay, followed by Drying and theprogramme duration.

– With sensor drying programmes thedrying level reached, e.g. Machineiron ... Hand iron... etc., will appearin the display later on.

You can select the following whiledrying is in progress:

– Timer to call up the current time ofday and the estimated end time ofthe programme.

– Save to save the current programmeas a favourite.

– Cancel to cancel the currentprogramme.


16

Estimated time remaining

When a programme is selected theestimated drying time will appear in thedisplay. Please be aware that it is onlyan estimate!

The following factors all affect theestimated time remaining: residualmoisture content after spinning; type offabric; size of load; room temperature;fluctuations in power supply.

The electronics continually assessconditions in the machine and adjustthe estimated time remaining for a moreaccurate reading. Because of this thetime displayed can alter during thecourse of a programme.

In the same way, the Woollenshandcare and Smoothing programmescan finish earlier than expected if acertain temperature is reached. Thiscan happen with particularly finefabrics or if items were partly drybeforehand.

Before the end of a programme

There is a cooling down phase at theend of the drying sequence: Coolingdown will appear in the display. Theprogramme will not finish until thecooling down phase has beencompleted.There is no cooling down phase at theend of the following programmes:Woollens hand care, Smoothing.

At the end of a programme

Anti-crease action (if selected) andFinish will appear in the display at theend of the programme.During the anti-crease phase (ifselected) the drum will turn at intervalsfor an hour to help prevent creasing.

E Remove the laundry

^ Press the a button to open the door.

^ Remove the laundry.

Check that all items have beenremoved from the drum. If items areleft in the dryer, they could bedamaged by overdrying when thedryer is next used.

The drum lighting will come on whenthe door is opened. It will go out a fewminutes later to save energy.

^ Close the door.

Maintenance after each dryingprogramme

^ Please see "Cleaning and care" fordetails.


17

You can programme your four most frequently used dryingprogrammes to appear in the left hand side of the display.The Save option must be activated via theSettings/Supervisor level menu before they can beprogrammed. This must be done by a Miele servicetechnician.

Selecting/changing a favourite^ Close the door.

Entry menu



3 Woollens handcare

4 Smoothing 10:00

^ Use the multi-function selector to select the programmeyou want and confirm your selection.

Main menu

Cottons Normal

Duration: 1:16 h

Low temp.H

Timer YH

SaveH

Back AH

^ You can highlight the programme (Cottons) or the dryinglevel again (Normal) by turning the multi-function selector.

^ Confirm your selection of the part you want to change bypressing the multi-function selector once.

Depending on the option highlighted, the following will be displayed:

– Programme selection

Programme Back A

selection Cottons

Minimum iron

Woollens handcare H

^ Use the multi-function selector to select the programmeyou want and confirm your selection.

Favourite programmes

18

Important: If you do not make a selection in the sub-menuwithin approx. 20 seconds, the display will revert to the mainmenu.

– Drying levels programme

Cottons Normal+

Drying levels from cMachine iron - Extra dry

^ Use the multi-function selector to select the drying level youwant and confirm your selection.

– The display will show which drying levels can be selectedfor each individual programmes.

– Warm air, Cool air programmes

Warm air 0:30 h

10:00Finish: 10:30

Duration: 0:30 h

^ You can use the multi-function selector to increase (up to amax. of 2 h cold/1h warm) or decrease the duration.

The programme end time for the duration selected will alsoappear.

– Other programmes

You cannot alter the drying level or duration for the otherprogrammes.


19

Low temperature

Cottons Normal+Low temp.

Duration: 1:47 h

Low temp. BH

Timer YH

SaveH

Back AH

^ Select Low temperature for all delicate or minimum ironfabrics with the r care label (e.g. acrylic garments).

– Delicate fabrics are dried at a lower temperature.

– The programme duration is longer.

Saving a favourite programme^ Select Save.


Previous : Cottons Normal

Save to : 1 2 3 4 Back A

^ Use the multi-function selector to select the number youwant and confirm your selection. Your settings have nowbeen saved with the favourite programme and will appearin the Entry menu.

Repeat the procedure if you want to customise other favouriteprogrammes, and save them to short cut buttons which havenot yet been used.


20

The timer can be used to select when you want theprogramme to end (if this option has been activated by aMiele service technician). The programme start can bedelayed to start automatically in 30 minute intervals up to amaximum of 24 hours.

To open the Timer sub-menu


Duration: 1:47 h

Low temp. B Timer Y Save Back A

H H H H

^ Select Timer. This opens the Timer sub-menu.

To select a delay start time


10:00Start: 10:13

Finish: 12:00

^ Use the multi-function selector to select the programmeend time and confirm your selection.

The programme end time will be adjusted to the next full orhalf hour. Once the end time has been entered, the starttime of the programme will also appear.

To start the timer

^ Press the Start button.The timer will count down in minutes until the start of theprogramme. If the delay start time selected is more thanone hour, the drum will turn briefly every hour to preventcreasing.

To cancel the timer

^ Select Cancel and Back.

Timer

21

Cottons Max. load: 6.5 kg*

Extra dry, Normal+, Normal**

Fabrictype

Single and multi-layered cotton fabrics such as towelling, jerseywear,underwear, flannelette bed linen.

Notes – Select Low temperature for fabrics with the r symbol.– Select Extra dry for multi-layered and very thick fabrics.– Do not use Extra dry for jersey fabrics as they have a tendency to

shrink.

Hand iron r, Hand iron rr **, Machine iron

Fabrictype

Cottons or linen fabrics, e.g. table linen, bedlinen, starched laundry.

Notes – Select Low temperature for fabrics with the r symbol.– To prevent laundry from drying out it should be rolled up until you

are ready for ironing.

Minimum iron Max. load: 3.5 kg*

Normal+, Normal**, Hand iron r

Fabrictype

Minimum iron items made of cotton, synthetic or blended fabrics, e.g.shirts, blouses, skirts and table cloths.

Notes – Select Low temperature for fabrics with the r symbol.– Select Hand iron for delicate fabrics and to reduce creasing even

more, reduce the load to 1.5 kg*.– In the Minimum iron Hand iron programme, items are dried with

very little creasing, depending on fabric type and amount oflaundry.

* Weight of dry laundry** Note for test institutes:

Use this programme without selecting Low temperature when testing accordingto EN 61121 Standard.

Programme chart

22

Woollens hand care Max. load: 2.5 kg*

Fabrictype

Woollen fabrics.

Notes – To refresh and fluff up woollen garments quickly. Woollen fabricsare not dried completely by this programme.

– Remove garments as soon as the programme has finished andleave to finish drying at room temperature.

Smoothing Max. load: 3.0 kg*

Fabrictype

– Cotton and linen fabrics.– Minimum iron items made of mixed fibres, cottons or synthetics,

e.g. trousers, jackets, shirts.

Notes – Smooths out creasing caused during the spin cycle in the washingmachine.

– Fabrics are not completely dried in this programme. Removegarments as soon as the programme has finished and leave tofinish drying at room temperature.

Cool air Max. load: 6.5 kg*

Fabrictype

Any item which only needs airing.

Warm air Max. load: 6.5 kg*

Fabrictype

– "Voluminous" or multi-layered fabrics whose layers have differentdrying characteristics, e.g. jackets, pillows.

– For drying individual items, e.g. bath towels, bathing costumes,tea-towels.

Notes – Select Low temperature for fabrics with the r symbol.– Do not select the longest drying time to start with. Check the items

as you are drying them to find the optimum time.* Weight of dry laundry

Programme chart

23

Denim Max. load: 3.5 kg*

Normal, Hand iron r

Fabrictype

Denim fabrics, e.g. jeans, jackets, skirts, shirts.

Shirts Max. load: 2.5 kg*

Normal, Hand iron r

Fabrictype

Shirts and blouses.

Outerwear Max. load: 3.5 kg*

Normal, Hand iron r

Fabrictype

Outerwear which is suitable for drying in a tumble dryer.

Proofing Max. load: 2.5 kg*

Fabrictype

For drying microfibre fabrics, skiwear, fine, closeweave cottongarments (poplin) or tablecloths which are suitable for drying in atumble dryer and have been treated to provide a water and dirtresistant finish.

Notes – This programme includes a proofing fixing phase.– Only use proofing agents which are stated by the manufacturer

as being "suitable for use on membrane textiles" as thesecontain fluorochemical compounds.

– Do not dry items which have been treated with proofing agentscontaining parafin. Fire hazard!

Towelling Max. load: 2.5 kg*

Normal +

Fabrictype

Single and multi-layered towelling items, e.g. towels, bath robes, terrysheeting.

* Weight of dry laundry

Programme chart

24

Payment system

If your machine is fitted with apayment system, opening the dooror cancelling the programme after ithas started may cause loss ofcredit*.

* A Miele service technician can re-setthe payment system so thatprogramming changes can be madewithin a specified time period.

Cancelling a programme^ Select Cancel.

The items will be cooled down. Finishwill appear in the display if youconfirm Cancel again.

^ Press the a button.

^ Open the door.

^ Close the door.

^ Select a different programme.

Adding or removing laundryafter a programme has started^ Press the a button.

^ Open the door.

,Do not touch the back of thedrum when adding or removingitems. The drum could be very hot -danger of burning.

^ Add or remove items.

^ Close the door.

To continue drying

^ Press the Start button.

The time left shown in the display maynow vary from the actual drying time.

Changing the programme sequence

25

Cleaning the fluff filtersFluff from items being dried is collectedby the fluff filters in the door and thedoor opening. Clean the filters aftereach drying programme*.

Cleaning them whilst dry

^ Open the door and pull the fluff filter(1) out as illustrated.

^ Use your fingers or a vacuum cleanerto remove the fluff from the surface of

the filter.

^ Remove any fluff from the hollow partof the door opening. You could alsouse a cleaning brush which isavailable as an optional extra fromyour Miele dealer or the Miele SpareParts Department or use a vacuumcleaner.

^ Once clean, push the filter back intothe door holder until it clicks intoposition. Ensure it is facing thecorrect way.

^ Also clean the door seal (2) with adamp cloth.

^ Use your fingers or a vacuum cleanerto remove the fluff from the two flufffilters in the door opening.

^ Close the door.

,* The fluff filters should bechecked and cleaned regularly butalways clean immediately the Cleanthe airways message appears.

Cleaning and care

26

Cleaning them with water

If there is a great deal of compactedfluff on any of the filters, they can beremoved and cleaned under hotrunning water.

^ Open the door and pull the fluff filterout of the door as describedpreviously.

The two filters in the door opening canalso be removed if you need to cleanthem with water.

^ Turn catch a until you hear it click.

^ Pull the filter by the dial out of thedoor opening as shown b. Do thesame on the other side.

^ Rinse all the filters under hot, runningwater.

^ Dry the filters thoroughly with care.

Replacing the filters

,Do not replace the filters if theyare damp or wet. Damp or wet filterscould cause operational faults.

^ Push the large filter back into thedoor holder until it clicks into position.Ensure it is facing the correct way.

^ Replace the filters in the dooropening by first inserting them at thebottom and then pressing them intoplace at the top.

^ Lock both catches (you will hearthem click).

Cleaning and care

27

Cleaning the tumble dryer

,Disconnect the machine from themains electricity supply.

,Do not use solvents, abrasivecleaners, glass cleaners orall-purpose cleaners. These coulddamage plastic surfaces and otherparts.

,The machine must never behosed down.

^ Clean the housing and the controlpanel with a slightly damp cloth anda mild detergent or soapy water.

^ The drum and other stainless steelparts can be cleaned with a suitablepropietary stainless steel cleanerfollowing the manufacturer'sinstructions.

^ Dry all parts with a soft cloth.

^ A microfibre E-Cloth is available fromthe Miele UK Spare Parts Departmentwhich is suitable for cleaningsurfaces such as stainless steel,glass, plastic and chrome without theuse of chemicals.

Cleaning and care

28

Cleaning the heat exchanger

,Check the heat exchanger unitregularly. It should always becleaned immediately the Clean theheat exchanger or Clean the airwaysmessage appears.

Removing the heat exchanger

^ Open the access panel.The hooks at the side will prevent thepanel from falling off.

^ Now remove the panel by pulling itdiagonally upwards.

^ Then place it to one side.

^ Turn the lever on the inner coverdownwards to the vertical position.

^ Pull the cover forwards.

^ Remove it by pulling it diagonallyupwards.

^ Turn the lever on the heat exchangerto the vertical position.

Cleaning and care

29

^ Pull the heat exchanger unit out of itshousing by the handle.

Checking the heat exchanger unit

^ Hold the heat exchanger unit up tothe light as shown.

^ Check to see if there is any fluffinside it.The arrows in the illustration aboveindicate where to look.

If you cannot see any fluff:

^ Replace the heat exchanger unit (seefollowing page).

If you can see some fluff:

^ Clean the heat exchanger unit asdescribed below.

Cleaning the heat exchanger unit

^ When rinsing the heat exchangerunit, make sure you position it asshown in the next two illustrations.

^ Use a shower head or similar to rinsethe unit out as shown.

Cleaning and care

30

^ Then flush the unit through from thefront.

^ Check the heat exchanger unit againfor any visible fluff and if necessaryflush it through again until it has allgone.

^ Shake any excess water out of theunit until no more water droplets arevisible.

^ Remove any soiling still visible insidethe housing unit by hand using anddamp cloth. Do not try and accessareas you cannot reach by hand!

^ Also make sure the rubber seals areclean.

The rubber seals must not beremoved and must be free of kinks.

Replacing the heat exchanger unit

^ With the handle facing upwards,push the heat exchanger unit backinto position in its housing.

^ Turn the lever down to the horizontalposition, making sure that the hookon the lever clicks into the groove.

When replacing the cover aftercleaning, ensure that the rubber sealfits correctly into the groove.

^ Replace the cover making sure thehooks locate correctly. Hold it at anangle and push it gently downwards.

^ Then turn the lever upwards into thehorizontal position to lock the cover.

^ Replace the service panel and pressthe upper edge until it clicks intoposition.

,It is important to ensure that boththe heat exchanger unit and thecover are correctly positioned andlocked otherwise water may leakfrom the machine.

Cleaning and care

31

Problem solving guideWith the help of the following notes minor faults in the performance of theappliance, some of which may result from incorrect operation, can be put rightwithout contacting the Service Department.

Repair work to electrical appliances should only be carried out by a suitablyqualified person in accordance with local and national safety regulations.Repairs and other work by unqualified persons could be dangerous. Themanufacturer cannot be held liable for unauthorised work.

Fault messages in the display

Problem Possible cause Remedy

l

Adjust

the load

This is not a fault.The electronic unit hasrecognised that there is nolaundry in the drum andcancelled the programme.Drying individual garments oritems which are already drycan also cause the programmeto be cancelled.

Use the Warm airprogramme (timeddrying) to dry individualitems.To delete the faultmessage:– Open the door.

,Technical

Fault

No obvious cause.In some circumstances, Cleanthe airways will have appearedin the display already.

– See next page: Cleanthe airways.

To delete the faultmessage:– Confirm with OK.

There is a fault, if despite doingthis, the programme iscancelled and the faultmessage appears again.

Contact the Miele ServiceDepartment.

Problem solving guide

32


The followingappears at theend of theprogramme:Maintenancemessage

Clean the heatexchanger.

The dryer is remindingyou that heat exchangerunit needs cleaning.

– Clean the heat exchanger.To delete the fault message:– Confirm with OK.

You can adjust the settingwhich controls when or ifthe Maintenancemessage appears.

– See "Settings menu J,Cleaning the heat exchanger".

Clean the

airwaysThe dryer is not workingefficiently oreconomically.Possible causes: The flufffilters are clogged withfluff or with detergentresidues.

– Cleaning the fluff filters isusually all that is required.However, if the Clean theairways message does not goout after you have cleanedthem, then also check all thepossible causes describedunder "The drying processgoes on too long or evenswitches off".

To delete the fault message:– Confirm with OK.

You can adjust the setting whichcontrols when or if the messageClean the airways appears.– See "Settings menu J, Clean

the airways".

Drain fault The drain hose is kinked. – Remove the kink.

To delete the fault message:– Confirm with OK.


33

Other problems


The dryingprocess goeson too long orevenswitches off.

In some circumstances the following message also appears:Clean the airways.Please check all the possible causes and open and shut thedryer door.

Ventilation to and from thedryer may be insufficient (e.g.because it is installed in asmall room). This has causedthe temperature in the roomto rise sharply.

Open a door or window while themachine is in operation forincreased air flow.

The vents below the door areblocked.

– Remove any objects that areblocking the vents.

The fluff filters are clogged upwith fluff or were still wetwhen they were replaced.

– Remove any fluff.– The fluff filters must be

completely dry.

Detergent residues, hair andfine fibres can block the heatexchanger.

Check the heat exchanger fromtime to time and clean it ifnecessary.

The laundry has not beenspun sufficiently.

Make sure that your laundry isthoroughly spun at theappropriate spin speed.

The tumble dryer has beenoverloaded.

Do not exceed the maximumload for the programmeselected.

Metallic components, e.g.zips have prevented the dryerfrom registering the correctmoisture level in the laundry.

– Open zips next time.If the problem occurs again, drygarments with long zips usingthe Warm air programme (timeddrying).

The laundryis notsufficientlydry.

The load consisted ofdifferent fabrics.

– Finish drying using the Warmair programme (timed drying).

– Select a different programmenext time, see Programmechart.


34


The heat exchangerunit service panelwill not shut.

The inner cover of the heatexchanger unit has not beenlocked properly and/or theheat exchanger unit has notbeen positioned correctly.

– Ensure that the heatexchanger unit ispositioned correctly andlock the cover.

– Check the rubber seals.

Water leaks fromthe machine afterthe heat exchangerunit has beencleaned.

Fluff has collected at thebottom of the condenser unithousing.

– Use a cloth to removeany fluff from the insideof the condenser unithousing.

Items made ofsynthetic fibres arecharged with staticelectricity afterdrying.

Synthetic fibres tend toattract static charge.

Static charge can bereduced by adding a fabricconditioner to the final rinsein the washing programmeor a fabric conditioner sheetto the load when drying.

There is a build upof fluff.

Fluff is principally the resultof friction when garmentsare being worn and washed.Machine drying hardlycauses any fluff to form andhas been established byresearch institutes to haveno appreciable effect on thelifetime of the garment.

Fluff is collected by the flufffilters and can be easilyremoved (see "Cleaningand care").


35


The programmedoes not start andthe display is dark.

No obvious cause. – Is the dryer switched on?– Is the door closed properly?– Has the fuse or circuit

breaker tripped?

The interior drumlighting does notcome on.

The lighting switches offautomatically (to saveenergy).

It will switch on again after thedoor has been closed andthen opened.

The lamp needschanging.

Change the lamp asdescribed at the end of thissection.

The display is in adifferent language.

A different language hasbeen selected in theSettings - Language Jmenu.

Set the language you want.The flag symbol will guideyou.

The Start buttonlight will flash whena programme isbeing selected.

This is not a fault.The flashing indicatesthat a programme can bestarted.

After the programme hasstarted, the flashing willchange to a constant light.

The display is darkand the light ringaround themulti-functionselector is not lit up.The Start button isflashing slowly.

The display has switchedoff automatically to saveenergy (Standby mode).

The display and themulti-function selector will lightup when one of the buttons ispressed.

The lighting is defective ifit does not come on whenone of the buttons ispressed.

Contact the Miele ServiceDepartment.


36

Changing the lamp

Disconnect the machine from themains electricity supply.

^ Open the door.

You will find the interior lamp cover atthe top of the drum aperture.

^ Insert a suitable tool, such as a widebladed screwdriver, under the sideedge of the lamp cover as illustrated.

^ Apply a little pressure and whilstdoing so turn your wrist in thedirection of the arrow to open thecover.

The cover will open downwards.

The temperature resistant lamp shouldonly be ordered from your Miele dealeror the Miele Spare Parts Department.

The lamp specification andmaximum wattage is stated on thedata plate and on the lamp cover.

^ Replace the lamp.

^ To close the cover push it upwardsand press it on the left and right untilyou hear it click into position.

,Ensure that it is fitted intoposition securely, as any moisturecould cause a short circuit.


37

In the event of any faults which youcannot remedy yourself, or if themachine is under guarantee, pleasecontact

– your Miele dealer, or

– the Miele Service Department(see back cover for contact details).

When contacting the your dealer or theService Department, please quote themodel and serial number of yourmachine, both of which are shown onthe data plate situated on the righthand side below the drum aperture.

PC / Optical interfaceThe indicator or check light marked PCon the fascia panel is the interfaceused by Miele service techniciansduring servicing work for testingpurposes and for undating themachine's programme data.

Optional accessoriesOptional accessories for this dryer areavailable from your Miele Dealer or fromthe Miele Spare Parts Department.

Please note that telephone calls maybe monitored and recorded fortraining purposes.

After sales service

38

View from the front

a Mains connection cable

b Control panel

c Door

d Service panel for heat exchanger

e Four height adjustable screw feet

f External drainage options (e.g. viawash basin, wash basin drain outletor gully)optional accessory: extension hose

Installation and connection

39

View from the side

View from the rear

a Protruding lid edge (see arrows) forholding when moving the machine

b Steel plinth base (optional accessory,available open or closed)

View from above

Washer-dryer stack

The tumble dryer can be combined witha Miele washing machine in awasher-dryer stack. A stacking kit isrequired which can be purchased fromyour Miele Dealer or the Miele SpareParts Department. The stacking kitmust be fitted by a Miele authorisedservice technician.


40

Installation on a concrete plinth

^ Secure the front feet of the dryer withclamps when installing the machineon a concrete plinth.

Payment system

The dryer can be fitted with a paymentsystem (optional accessory).This must be connected andprogrammed by a Miele Servicetechnician.

Coins / tokens must be removedfrom the payment system regularly,otherwise it will become blocked.

,Do not use devices to turn themachine off automatically, (e.g. auto-matic timers).


41

Installation site

,Make sure the dryer door can beopened without hindrance afterinstallation.

Transporting the machine to itsinstallation site

When moving the machine you canhold it by the lid where it protrudes tothe rear of the dryer. To manoeuvre thedryer out of its packing case to itsinstallation site you will also need tohold it by the front feet.

Levelling the machine

The machine must be perfectly level toensure safe and proper operation.

^ The screw feet can be adjusted tocompensate for any unevenness inthe floor.

,The ventilation gaps in the plinthand the front panel must not becovered over as this would prevent asufficient intake of air.

This tumble dryer is not suitable forbuilding under.

Room in which the dryer is located

Air taken in for use in the dryingprocess will be warm when it isexpelled from underneath the dryer.This expelled air heats up the air in theroom. It is therefore very important toensure that the room is adequatelyventilated, particularly if the dryer islocated in a small room. Otherwiserunning times and energy consumptioncould be increased.


42

External drainage of thecondensed water

The condensed water is pumpedaway through the drain hose which islocated at the back of the dryer at thebottom.

Drain hose length: . . . . . . . . . . . . . . 2 m

Delivery head: . . . . . . . . . . . . . . . . . 1 m

,Do not pull on the drain hoseand do not allow it to becomekinked as this could damage it.

Drain hose connection:

1. Direct into a sink or basin.

– Hook the hose over the edge andsecure.

– Use the bow-shaped guide (seeillustration on the right).

2. Connected securely to a floor gully.

3. Connected directly to a sink drainoutlet.

Connection to a sink drain outlet

To connect the drain hose to a sinkdrain outlet you will need to use theadapter and hose clip located at theback of the dryer at the bottom.

^ Remove adapter 1 and hose clip 3behind it.

^ Fit adapter 1 to the sink drain outletusing nut 2.

^ Secure the drain hose with hose clip3 to the nut.


43

Electrical connection U.K.All electrical work should be carried outby a suitably qualified and competentperson, in strict accordance withnational and local safety regulations.

Ensure power is not supplied to theappliance until after installation workhas been carried out.

The appliance is supplied with a mainscable with moulded plug ready forconnection to a 230-240V mainssupply. The voltage and connectedload are given on the data plate.Please ensure these match the on-sitemains supply. The fuse rating is quotedon the plug.

Connection should be made via asuitable switched socket which is easilyaccessible after installation.

For extra safety it is advisable to installa residual current device (RCD), with atrip current of 30 mA (in accordancewith DIN VDE 0664, VDE 0100 Section739).

Do not connect via an extension lead.Extension leads do not guarantee therequired safety of the appliance (e.g.danger of overheating).

Non-rewireable plugs BS 1363

The fuse cover must be refitted whenchanging the fuse, and if the fuse coveris lost, the plug must not be used until asuitable replacement is obtained. Thecolour of the correct replacement coveris that of the coloured insert in the baseof the plug, or the colour that isembossed in words on the base of theplug (as applicable to the design ofplug fitted).

Replacement fuses should be ASTAapproved to BS 1362 and have thecorrect rating. Replacement fuses andfuse covers may be purchased fromyour local electrical supplier.

WARNING: THIS APPLIANCEMUST BE EARTHED


44

Height 850 mm (adjustable +7 / -7 mm)

Width 595 mm

Depth 700 mm

Depth with door open 1188 mm

Weight 58 kg

Drum volume 130 litres

Maximum capacity 6.5 kg dry weight

Length of connection cable 1600 mm

Voltage see data plate

Connected load see data plate

Fuse rating (UK) see plug

Lamp wattage see data plate

Test certificates awarded Radio / TV suppression, VDE

Max. load bearing in operation approx. 72 kg

Noise level(according to 3. GSGV)

< 70 dB (A)

Technical data

45

46

Settings menu Jfor changing standard settings

The Settings menu is used to alter thedryer's electronics to suit differentrequirements.Settings can be altered at any time.

47

To open the Settings menu



3 Woollens handcare

4 Smoothing 10:00

^ Select Settings J from the entry menu and confirm yourselection with the multi-function selector.

Selecting settings

Settings Back A

Language F ...

Anti-crease action

Buzzer H

^ Select the setting you want to change and confirm yourselection.

If you do not make a selection in the sub-menu within approx.20 seconds, the display will revert to the main menu.

To close the Settings menu

^ Select Back and confirm your selection.The display will revert to the entry menu.

Settings menu J

48

Language J

The display can be set to appear inone of several different languages forthe current programme.

To select the language you want, gointo the Languages J sub-menu.

^ Select the language you want andconfirm your selection.

The flag after the word Language actsas a guide to prevent a language whichwill not be understood from being set.

The different language setting will onlyapply to the programme currently inuse. After the programme has finishedthe display will revert to the defaultlanguage which was set in theSettings/Supervisor level menu.

Anti-crease action

The drum will continue to rotate atintervals for one hour to preventlaundry creasing, if you do not wishto remove it immediately.

The machine is delivered with thisoption activated (On).

Buzzer

When the buzzer function has beenactivated, an audible tone sounds atthe end of a programme.

The buzzer will still sound if there is afault even if it has been deactivated.

OffThe machine is delivered with thebuzzer deactivated.

NormalThe buzzer sounds at the end of aprogramme.

LoudThe buzzer sounds at maximum volumeat the end of a programme.

Time of day

First select either a 24 hour or12 hour clock.Then set the current time of day.

24h clockThe time of day will appear as a24 hour clock.

12h clockThe time of day will appear as a12 hour clock.

No clockThe time of day is not displayed. Therelative time will appear in the displaywhen Timer is selected.

Settings menu J

49

Display contrast

Display brightness

There are ten different displaycontrast and display brightnesssettings.

The bar chart shows you the setting.

Standby

To save energy, the display goes outafter 10 minutes and the Start buttonflashes slowly.

On

Standby is activated:

– if a programme is not selected.

– after the Start button has beenpressed.

– at the end of a programme.

Not in current Prog.(the machine is delivered with thisoption selected)

Standby is activated:

– if a programme is not selected.

Operating the multi-function selectorswitches the display back on again.

Extending the cooling downtime

The cooling down phase which takesplace before the end of a programmecan be lengthened if required. Thismakes the garments easier tohandle.

The bar chart shows you the setting.The machine is delivered with 0 mins(normal cooling down period) set asstandard.

– The programme duration willincrease accordingly.

You cannot extend the cooling downtime for the Warm air, Cool air, Woollenshandcare or Smoothing programmes.

Settings menu J

50

The Settings/Supervisor level needs to be activated by aMiele service technician.

The Settings/Supervisor level is locked with a code toprevent it being accessed by non-authorised personnel(the Language J setting can still be altered).

Settings Back A

Supervisor level Access via code

^ Select Access via code and confirm your selection.

To enter the code

Enter the code 0 0 0 (factory default setting). If you enter thecode wrongly three times, the machine will lock out for anhour!

0 _ _

Please enter code

^ Turn the multi-function selector until the first numberappears. Confirm your selection of this number.

^ Repeat the process until all three numbers have beenentered.

After you have entered the last number you need to confirmthe code:

0 0 0

Please confirm code

OK

H

back AH

^ Confirm the code.

The supervisor level is now open.

Settings/Supervisor level menu

51

Select languages

You can select the order that youwant the languages available toappear in in the display.

Supervisor level

You can alter the access code to thesupervisor level.

^ Enter the old code.

^ Enter a new code.

After you have confirmed the newcode, the display will change to thebeginning of the Settings menu.

Save

You can choose whether you wantthe Save option to appear in the mainmenu. The save function is required ifyou want to change the favouritedrying programmes listed in thedisplay.

The machine is delivered with thisoption deactivated.

Drying levelsThe bar chart shows you the setting.The machine is delivered with amedium settings set as standard.

– Depending on the setting, theprogramme duration will be shorter(Damper) or longer (Drier).

Cottons and Minimum iron dryinglevels

You can alter the drying levels for theCottons and Minimum ironprogrammes.

Cottons Machine iron drying level

This drying level can be alteredindividually.


52

Cleaning the airways

Fluff should be removed after drying.The Clean the airways message willremind you to clean the filters when acertain amount of fluff has collected.You can decide at what level of fluffthis reminder should be given.

You will have an idea of how often thisshould be done after a few dryingprogrammes.OffClean the airways does not appear

HeavyClean the airways only appears whenthere is a heavy build-up of fluff

NormalFactory default setting

LightClean the airways appears when thereis only a small build-up of fluff

Cleaning the heat exchanger

Check the heat exchanger unit fromtime to time and clean it if necessary.The Clean the heat exchangerMaintenance message will remindyou. You can decide after how manyhours you want the message toappear.

Setting the correct option will dependon how much fluff and dust hasaccumulated.Select a more appropriate option if youfind that the heat exchanger is verydirty/not very dirty at the end of the setperiod of time.

The machine is delivered with thisoption set at: 400 hours.

Displaying the residualmoisture as a percentage

The residual moisture of the dryingstage reached can also be displayedas a % during the programmesequence.

The machine is delivered with thisoption set at: Without percentage.

Cool air free of charge

If the dryer has been fitted with apayment system you can set the Coolair programme to be free of charge.

The machine is delivered with thisoption set at: Free of charge.


53

54

55

Alteration rights reserved/1505 M.-Nr. 06 511 380 / 00en - GB

Documents

Operating and installation instructions for condenser ... · workwear. Such clothing may require a heavy duty detergent to get them clean. If necessary consult the detergent manufacturer