MON-LCD19BL-CCTV original part. ... English - 1 INTRODUCTION. English - 2 ... and effortless. The monitor features Advanced Color Controls for fine-tuning

MON-LCD19BL-CCTV

Reference Manual

1. Read all of these instructions.

2. Save these instructions for later use.

3. Unplug this monitor from thewall outlet before cleaning. Do notuse liquid cleaners or aerosolcleaners. Use a damp cloth forcleaning.

4. Do not use attachments not recommended bythe monitor manufacturer as they may causehazards.

5. Do not use this monitor near water, e.g., near abathtub, washbowl, kitchen sink, or laundry tub,in a wet basement, or near a swimming pool, etc.

6. Do not place this monitor on anunstable cart, stand, or table. Themonitor may fall, causing seriousinjury to a child or adult, andserious damage to the appliance.

7. Slots and openings in thecabinet and the back or bottom areprovided for ventilation, to ensurereliable operation of the monitor,and to protect it from overheating.

These openings must not be blocked or covered.The openings should never be blocked byplacing the monitor on a bed, sofa, rug, or othersimilar surface. This monitor should never beplaced near or over a radiator or heat register.This monitor should not be placed in a built-ininstallation such as a bookcase unless properventilation is provided.

8. This monitor should be operatedonly from the type of power sourceindicated on the marking label. Ifyou are not sure of the powersupplied to your home, consult

your monitor dealer or local power company.

9. This monitor is equipped with a3-wire grounding-type plug, Thatis, a plug having a third(grounding) pin. This plug willonly fit into a grounding-type

power outlet. This is a safety feature. If you areunable to insert the plug into the outlet, contactyour electrician to replace your obsolete outlet.Do not defeat the purpose of the grounding-typeplug.

10. Do not allow anything to reston the power cord. Do not locatethis monitor where the cord will beabused by people walking on it.

11. Follow all warnings and instructions markedon the monitor.

IMPORTANT SAFEGUARDS

12. For added protection for thismonitor during a lightning storm,or when it is left unattended andunused for long periods of time,unplug it from the wall outlet. This

will prevent damage to the monitor and/or thecomputer due to lightning and power line surges.

13. Do not overload wall outlets and extensioncords as this can result in fire or electric shock.

14. Never push objects of any kind into thismonitor through cabinet slots, as they may touchdangerous voltage points or short out parts thatcould result in a fire or electric shock. Never spillliquid of any kind on the monitor.

15. Do not attempt to service thismonitor yourself, as opening orremoving covers may expose youto dangerous voltages or otherhazards. Refer all servicing to

qualified service personnel.

16. Unplug this monitor from the wall outlet andrefer servicing to qualified service personnelunder the following conditions:

a. When the power cord or plug is damaged orfrayed.

b. If liquid has been spilled into the monitor.

c. If the monitor has been exposed to rain orwater.

d. If the monitor does not operate normally byfollowing the operating instructions. Adjust onlythose controls that are covered by the operatinginstructions, as improper adjustment of othercontrols may result in damage and will oftenrequire extensive work by a qualified technicianto restore normal operation.

e. If the monitor has been dropped or the cabinethas been damaged.

f. When the monitor exhibits a distinct change inperformance, this indicates a need for service.

17. When replacement parts arerequired be sure the servicetechnician has used replacementparts specified by the manufacturerthat have the same characteristics as

the original part. Unauthorized substitutionsmay result in fire, electric shock, or otherhazards.

18. Upon completion of any service or repairs tothis monitor, ask the service technician toperform routine safety checks to determine thatthe monitor is safe to operate.

WARNING: FOR CONTINUED SAFETY, REPLACE POWER ADAPTOR ONLY WITHMANUFACTURER'S RECOMMENDED MODELS

FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT

NOTE : This equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radio frequency energyand, if not installed and used in accordance with the instructions, may cause harmfulinterference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures : - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio or monitor technician for help.

CAUTION : Any changes or modifications not expressly approved by theparty responsible for compliance could void the user’s authority to operate theequipment.

CANADIAN NOTICE

AVIS CANADIEN

This Class B digital apparatus meets all requirements of the CanadianInterference-Causing Equipment Regulations.

Cet appareil numérique de la Class B respecte toutes les exigences duRèglement sur le matériel brouilleur du Canada.

European Union Notice Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and thethe Low Voltage Directive (73/23/EEC) issued by the Commission of the EuropeanCommunity.

Compliance with these directives implies conformity to the following European Norms (inbrackets are the equivalent international standards):

• EN55022 (CISPR 22) - Electromagnetic Interference • EN55024 - Immunity Test for ITE Product• EN60950 (IEC950) - Product Safety• EN61000-3-2 (IEC555-2) - Power Line Harmonics

CONTENTSCONTENTS

Introduction ............................................................................. 1

Product Features ................................................................. 2

Setup ......................................................................................... 3

Stand Assembling Procedures ............................................ 3

Connecting the 15 Pin Signal Cable and Power Cord ......... 4

Connecting the others ............................................................. 5

Operation & Adjustment ....................................................... 6

Specifications ......................................................................... 16

Factory Preset Timings ......................................................... 18

Monitor rotation (Optional) .................................................. 19

Changing the Stand ............................................................... 20

Troubleshooting ..................................................................... 22

This manual explains how to correctly install, operate and get thebest performance from your monitor. Please read this user’sguide carefully before installing your monitor, then keep it nearyour monitor for quick reference.

First, please check that the contents of the box corresponds withthe following checklist :

• TFT LCD monitor

• Power cord

• RCA Cable

• 15 pin signal cable

• User’s guide

• Audio Cable (Optional)

• DVI Cable(optional)

• AC Adapter

If any item is missing or damaged, please contact your dealer.Please keep the box and packing materials so that you mayproperly store or transport your monitor.

English - 1

INTRODUCTIONINTRODUCTION

English - 2

PRODUCT FEATURES

The monitor is designed for use in a small work area or forthose who need more work space on the desk.

The convenient and user-friendly on-screen display allows foreasy and accurate adjustments of screen size, position andscreen color.

The monitor complies with the VESA Display Data Channel(DDC) specification for Plug and Play compatibility.Advanced microcircuitry makes setup and configuration fastand effortless.

The monitor features Advanced Color Controls for fine-tuningto meet your own personal tastes or application requirements.Use the on-screen controls to adjust the color temperature,RGB gain value for the best possible screen color and intensity.

Press the menu button and activate the Self-Diagnosis menu todetermine whether your monitor is functioning normally, notreceiving a signal or is receiving a signal that is out of scanningrange.

Activate the higher refresh rates of the monitor to stabilize thescreen and eliminate the annoying flicker that contributes toeye-strain and headaches.

The monitor supports the optimal display performance with1280x1024 at 75Hz.

The monitor can be connected to various types of video deviceswith supporting video input signals like Compositevideo(CVBS), Seperate video. The internal stereo speakers make the end user enjoy audiosound.

With the POWER LIGHT function added,you can enjoy thebright screen for movie or any other multimedia utilization.

English - 3

SETUPSETUP

•The monitor is packed with stand and main body separated.•Please join the stand with the main body before use.

Put some smooth pad or cloth on thelevel surface and place the monitoron it with the face downward.

Join the stand with the metalprotrusion from the bottom of themonitor’s main body.

Tighten the screw fully at thebottom of the stand by turning itclockwise three to four turns.

※ l After fully tightening the screw, bend theknob of the screw onto the bottom of thestand.

※ l When disassembling the stand, please follow the procedure of assemblingin reverse order.

Caution : Incomplete tightening of thescrew may cause themonitor unstable.

1

3

2

Stand Assembling Procedures

English - 4

CONNECTING THE 15 PIN SIGNAL CABLE AND POWER CORD

Turn off the computer and monitor.

Connect the 15 pin signal cable to the output port of the video card inyour computer and monitor.

Connect the DVI cable to the output port of the video card in yourcomputer and monitor. (Optional)

Connect the audio cable to the output port of the sound card in yourcomputer. (Optional)

Plug the DC jack into the DC in port located on the back of the monitor.

Plug the power cord into the AC receptacle of the Adapter.

Plug the other end of the power cord into the AC outlet.

DC 12VVIDEOOUT

IN STEREO OUTL AUDIO RIN

English - 5

DC 12V STEREOIN OUTINOUT VIDEO L RAUDIO

1 2 3

CONNECTING THE OTHERS

1. Plug the connector to the BNC port on the rear of themonitor (ex : Camcorder, VCR, DVD, ---).

2. Plug the connector to AUDIO INPUT port on the rear of themonitor (ex : Computer, CD Player, ---).

3. Plug the connector to AUDIO OUTPUT port on the rear ofthe monitor (ex : Speaker, Headphone, ---).

2

1

3

1. Turn on monitor.

2. Choose “VIDEO” connected to DVD player, using buttons ofremote controller or SOURCE button from exterioradjustment buttons.

3. Put tape or DVD into VCR or DVD player and play.

How to watch DVD, VIDEO

English - 6

OPERAOPERATION & ADJUSTMENTTION & ADJUSTMENT

CONTROL PANEL (Case #1)

POWER Indicator1

3

4

Adjusts volume up and afterpressing MENU, adjustsmenu settings

Adjusts volume down and afterpressing MENU, adjusts menusettings

Volume adjust

Volume adjust

Source

Up

8

6

Moves from top menu tosubmenu in the OSD windowand opens the function windowfor the selected icon.While the OSD screen off,selects input source and afterpressing SOURCE sets menufunctions.

Menu 5Turns the OSD window on.Turns the OSD (On-ScreenDisplay) window off and movesfrom sub menu to top menu inthe OSD window.

Selects Menu.While the OSD screen off,turns the sound on & off.

Down7Selects menu.While the OSD screen off,launches the AUTOTRACKINGfunction directly. (Analog mode)

Switches the monitor onand off.

POWER 2

Shows both normal operation and power management status withpower indicator light.

Sensor window Remote control. Receives signal from the Remote controller

English - 7

CONTROL PANEL (Case #2)

Shows both normal operation and power management status withpower indicator light.

POWER Indicator1

3

4

Adjusts volume up and afterpressing MENU, adjustsmenu settings

Adjusts volume down and afterpressing MENU, adjusts menusettings

Volume adjust

Volume adjust

Source

Up

8

6

Moves from top menu tosubmenu in the OSD windowand opens the function windowfor the selected icon.While the OSD screen off,selects input source and afterpressing SOURCE sets menufunctions.

Menu 5Turns the OSD window on.Turns the OSD (On-ScreenDisplay) window off and movesfrom sub menu to top menu inthe OSD window.

Selects Menu.While the OSD screen off,turns the sound on & off.

Switches the monitor onand off.

Sensor window Remote control. Receivessignal from the Remotecontroller

POWER 2

Down7Selects menu.While the OSD screen off,launches the AUTOTRACKINGfunction directly. (Analog mode)

English - 8

KEY PROCESS

To select MENU press the MENU button.

Use up- down button to select the main menu.

Use SOURCE button to select the sub menus on the right.

Use up-down buttons to select sub-menu function.

Press SOURCE button, then using left-right buttons you can makeadjustments as necessary

To exit press MENU.

English - 9

HOT KEY

When there is no OSD, if you press this ▼(Down/AUTO) button, you can use the bestdisplayperformance fit for a current mode.(Analog MODE)

Selects signal in order.ANALOG - DIGITAL - VIDEO

When there is no OSD, if you press this ▲(UP/MUTE) button, you can turns the soundon and off.

When there is no OSD, you can adjust thevolume directly.

English - 10

ADJUSTMENT PROCEDURE

No Raster

Adjust the CLOCK control.

Perform theH-POSITION

Perform the Autotracking

Is the H.SIZE proper?

Is the noise displayed onthe screen?

Adjust the CLOCK untilthe screen is cleared.

Is the noise displayed onthe screen yet?

Yes

Yes

No

No

End

Yes

English - 11

Color

Function

OSD FUNCTIONS WITH USING ANALOG MODE

Choose different preset color temperatures or set yourown customized color parameters.Color Temp.

Adjust the position of the display horizontally (left orright) and vertically (up or down).

H.Position &

V.Position

Remove any horizontal noise and clear or sharpen theimage of characters.

Adjust the width (horizontal size) of the screenimage.

Phase

Clock

Adjust the display image quality (if the screenproceed to scaling up).Sharpness

Choose automatically the proper horizontal position,vertical position & size of the screen image.Auto Adjust

OSD

Adjust the color.Color Adjust

Adjust the contrast of image, the difference betweenlight and dark areas on the screen. Contrast

Adjust the brightness of image.Brightness

Automatically eliminate any image shaking.Auto Colour

Picture

OSD

OSD

English - 12

OSD Menu

Misc.

Adjust the OSD Transparency.Translucent

Select language for OSD.(English/한국어)Language

Adjust the OSD position horizontally (left or right)and vertically (up or down).

OSD H & VPos.

Adjust the display OSD time.OSD Timer

Select input signal source. (D-SUB/DVI/CVBS)Signal Source

Select powerlight mode(PC/Game/Movie)Mode

Reset the screen to the Factory PresetDisplay Settings.Reset

Sound

Turn the audio sound on or off. Sound

Increase or decrease audio volume. Volume

OSD

OSD

OSD

English - 13

OSD FUNCTIONS WITH USING VIDEO/DIGITAL MODE

Adjust the display image quality (if the screenproceed to scaling up).Sharpness

Adjust the contrast of image.Contrast

Adjust the brightness of image.

Adjust saturation of image.

Brightness

Saturation

Adjust the hues of image.Hue

Color

OSD

MISC.

Select input signal source. (D-SUB/DVI/CVBS)Signal Source

Select powerlight mode(PC/Game/Movie)Mode

Reset the screen to the Factory Preset DisplaySettings.Reset

OSD MENU

Adjust the OSD transparencyTranslucent

Select language for OSD.(English/한국어)Language

Adjust the OSD position horizontally (left or right)and vertically (up or down).

OSD H & VPos.

Adjust the display OSD time.OSD Timer

OSD

OSD

English - 14

SOUND

Turn the audio sound on or off. Sound

Increase or decrease audio volume. Volume

OSD

English - 15

SELF DIAGNOSIS

If there is no image, the Self Diagnosis screen will be displayed.Self Diagnosis function checks if the status of the monitor screenis No Signal, Out of range or None support.

No Signal screen is displayed when the D-Sub signal connector is connected but thestatus of the monitor is on DPMS mode.

Out of Range screen is displayed when theapplied frequency is under or over normalrange.

Normal range(Non-interlaced mode only)

H : 30 - 80 KHz V : 56 - 77 Hz

Check cable screen is displayed when theAnalog signal cable is disconnected.

English - 16

SPECIFICASPECIFICATIONSTIONS

Panel Size 17-inch(43.2 cm) diagonal Pixel Pitch 0.264 x 0.264 mmViewing Angle 160°(H)

160°(V)Contrast Ratio 800:1(typ)Brightness 250cd/m2 brightness(typ)Response Time 5msecColor Filter RGB vertical stripe

Synchronization Horizontal 30 - 80 KHzVertical 56 - 77 Hz

Video Bandwidth 140MHzMax Resolution 1280 x 1024@75HzOptimal Resolution 1280 x 1024@60HzColors 16.7 M ColorsDisplay Area 337.9 mm x 270.3 mmPC Input Signal Sync H/V separate(TTL)

Video15 pin D-sub(Analog RGB)DVI-D (Optional)

AV Input Signal VIDEO BNC Input / OutputAUDIO RCA Left + Right Input

Stereo Mini Jack Input & OutputSpeaker Max. Output 4W ( Left 2W + Right 2W)Plug and Play VESA DDC CompatiblePower Source DC 12V, 3.33APower Consumption 26 Watt(typ.)Dimension-W x H x D 383(W) x 376(H) x 159 mm(with stand)

383(W) x 321(H) x 65 mm(without stand)Weight-net/gross 4.6Kg / 6.0 Kg (10.1 / 13.2 Lbs)Power Saving EPA, VESA DPMS, Nutek CompliantTilt Range 5° forward, 30° backwardOperating Temperature 0 ~ 40°C /50 ~ 104°F

<17 inch>

English - 17

Panel Size 19-inch(48 cm) diagonal Pixel Pitch 0.294(H)mm x 0.294(V) mmViewing Angle 160°(H)

160°(V)Contrast Ratio 800:1 (typ)Brightness 250cd/m2 brightness (typ)Response Time 5msecColor Filter RGB vertical stripe

Synchronization Horizontal 30 - 80 KHzVertical 56 - 77 Hz

Video Bandwidth 140 MHzMax Resolution 1280 x 1024@75HzOptimal Resolution 1280 x 1024@60HzColors 16.7 M Colors Display Area 376.32(H)mm x 301.056(V)mmPC Input Signal Sync H/V separate (TTL)

Video 15 pin D-sub(Analog RGB)DVI-D (Optional)

AV Input Signal VIDEO BNC Input / OutputAUDIO RCA Left + Right Input

Stereo Mini Jack Input & OutputSpeaker Max. Output 4W(Left 2W+Right 2W)Plug and Play VESA DDC CompatiblePower Source DC 12V, 3.33A Power Consumption 26 Watt(typ.)Dimension-W x H x D 427(W) x 415(H) x 159(D) mm(with stand)

427(W) x 358(H) x 66(D) mm(without stand)Weight-net/gross 5.4Kg / 7.0Kg (11.9 / 15.4 Lbs)Power Saving EPA, VESA DPMS, Nutek CompliantTilt Range 5° forward, 30° backwardOperating Temperature 0 ~ 40°C /50 ~ 104°F

<19 inch>

The LCD panel may have some defective pixels (e.g. slightly light or dark) due to acharacteristic of the LCD panel. But there is no defect in your LCD product itself.

The specification can be changed without any prior notice to improve the quality of the product.

English - 18

FFACTORACTORY PRESET TIMINGSY PRESET TIMINGS

VESA MODES

IBM MODES

MAC MODES

THE OTHERS

VGA 640 X 480@60Hz 31.5 60 Non-interlaced



SVGA 800 X 600@56Hz 35.2 56 Non-interlaced




XGA 1024 X 768@60Hz 48.4 60 Non-interlaced



SXGA 1280 X1024@60Hz 64.0 60 Non-interlaced


SXGA 1152 X 864@75Hz 67.5 75 Non-interlaced


EGA 640 X 350@70Hz 31.5 70 Non-interlaced

DOS 720 X 400@70Hz 31.3 70 Non-interlaced





Mode H.Freq (KHz) V.Freq (Hz) RemarkResolution(dots X lines)




The LCD Monitor has only Non-interlanced modes without flicker.

English - 19

Monitor rMonitor rotation (Optional)otation (Optional)

3. Rotate the monitor 90 degrees counterclockwise, and raise it up properly to thedesired angle from the fully leant position. If you want to return it to the originalposition, follow the procedure in reverse order.

4. If you want to use the screen in rotation function:You can use it with compatible official software.Alternatively, you can use it with VGA card that is compatible with screenrotation function in Window XP environment.

※ This product is not accompanied by software which supports the screen rotation function.

1 Lean the monitor’s main body backward fully.

Caution : If you lean the monitor backward, its corner may touch the surfaceunder it while rotated.

2 Adjust the cables or cords, if any, behind the monitor properly to rotatethe monitor safely.

If you want to rotate the monitor:

You can choose a rotation-type monitor which you can rotateto any direction as you want.(Please check whether the monitor can rotate or not when you purchase it.)

English - 20

Removing Original Stand

1. Detach the rear cover of the stand with a screwdriver.2. Remove the four screws connecting the stand and the body and the

stand is disassembled.

Turn off the monitor and pull out the power cable.

Place a cushion or a soft cloth on the floor and put the product on it withthe front of the monitor facing the floor.

CHANGING THE STCHANGING THE STANDAND

English - 21

ATTACHING THE MONITOR WITH THE ARM-STAND(OPTION)

Tighten up screws at the locationsindicated by arrows.

Supportstand Surface for

standinstallation

This monitor’s installation surface is compatible with various kindsof VESA standard stands.

Hole spacing : 100x100 mmScrew Length : 8~12 mm

English - 22

TROUBLESHOOTINGTROUBLESHOOTING

Adjust Clock to set the screen position and adjustClock fine until a noise isn’t displayed.

Check if power switch and computer power switchare in the on position.

Check if the signal cable is correctly connected tothe video card.

Check if the pins of D-sub connector are not bent.

Check if the computer is in the power- saving mode.

Check if power switch is in the on position.

Check if the power cord is correctly connected.

Check if the signal cable is suitable to the video card.

Adjust Clock or H&V Center to get the properimage.

Keep the devices that may cause electrical interference away from the monitor.

See the FCC information at the front cover of themanual.

Adjust Contrast and Brightness.

Check the audio cable are correctly connected to thecomputer.

Adjust the volume after checking the sound is muted.

Check the audio system in the computer.

Symptom

Picture is jitterd.

No picture.

POWER LED is notlit.

Image is unstable.

Image is notcentered, too smallor too large.

Picture bounces or a wave pattern ispresent in thepicture.

Picture is blurred.

No sound.

Check

English - 23

Adjust the volume on the OSD Menu.

Adjust the volume of the sound card in the computer.

Check if VIDEO mode has been set.

Check if the video terminal is properly connected.

Check if the video cable is correctly connected to thecomputer and set to the video mode.

Adjust the Saturation or Hue on the OSD Menu inthe video mode.

Adjust the Sharpness on the OSD Menu in the videomode.

Symptom Check

Low sound.

VIDEO screencannot be seen.

No video.

Poor color in thevideo.

Grainy picture in thevideo.

Documents

MON-LCD19BL-CCTV original part. ... English - 1 INTRODUCTION. English - 2 ... and effortless. The monitor features Advanced Color Controls for fine-tuning