MIL-C-12226G - SUPERSEDING MIL-C-12226F 28 …everyspec.com/MIL-SPECS/MIL-SPECS-MIL-C/download.php?...MIL-C-12226G 3.3 Material. 3.3.1 Basic material. The bas i c material for the

MILITARY SPECIFICATION

COVER, TOXICOIXIGICALAGENTS PROCTECTIVE GAS

MIL-C-12226G -23 December 1987SUPERSEDINGMIL-C-12226F28 December 1979

MASK HOOD, COOLING

This specification is approved for use by all @artments and Agencies of theDepartment of Ikfense.

1. SCOPE

1.1 scope. This specification covers the requirements for a hood coverfabricated fran cotton birdseye cloth. The cover shall be of one type and onesize.

2. APPLICABLE D3CUMENTS

*2.1 Government documents.

*2.1.1 Specifications, standards, and handbooks. The followingspecifications, standards, and handbooks form a part of this specification tothe extent specified herein. Unless otherwise specified, the issues of thesedocuments shall be those listed in the issue of the Department of EefenseIndex of S&cifications and Standards (EODISS) and supplement thereto, citedin the solicitation.

Beneficial ccmunents(reccmnendations,additions, deletions) and any pertinentdata which may be of use in improving this document should be addressed to:Officer in Charge, Navy Clothing and ‘l@xtileResearch Facility, 21 StrathmoreRoad, Natick, MA 01760-2490 by using the self-addressed StandardizationJlxument Improvement Proposal (DD Form 1426) appearing at the end of thisdocument or by letter.

AMSC N/A FSC 8415

DISTRIBUTION STATEMENT A. Approved for public release, distribution is‘unlimited.

Downloaded from http://www.everyspec.com

MIL-C-12226G

SPECIFICATIONS

FEDERAL

V-T-276CCC-C-425DDD-L-20

DDBT-86

NM-P-71

MILITARY

MIL-B-17757 -MIL-P-15011 -

MIL-T-43548 -

- Thread, Cotton- Cloth, Birdseye and Gauze; Cotton- =1; for Clothing, Equipage and Tentage

(General Use)- Tape, Textile; Cotton, General Purpose

(Un-bleached,Bleached, or D@)- Pallet, Material Handling, Vbod, StringerConstruction, 2 Way And 4 Way (Partial)

STANDARIX

FEDERAL

FED-STE4

FED-STE-191 -FED-STD-751 -

MILITARY

Boxes, Shipping Fiberboard (Modular Sizes)Pallet, Material Handling Vbod, Post Construction,4 way entryThread? Polyester Core: Cotton-, Rayon-f orPolyester-Covered

.

Glossary of Fabric Imperfections (Section 1, Ii,and Iii) o

Textile Test iYethcdsStitches, Seams and Stitchings

MIL-STD-105 -Sampling Procedures and Tables for Inspection byAttributes

MIL-STD-129 - Marking for Shipnent and StorageMIL-STD-147 - Palletized Unit Loads

(Copies of specifications, standards, drawings, and publications required bycontractors in connection with specific procurement functions should beobtained from the procuring activity or as directed by the contractingofficer.)

2.1.2 Other Government documents, drawings, and publications. Thefollowing other Government documents, drawings, and publications form a partof this specification to the extent specified herein. Unless otherwisespecifid, the issues shall be those in effect on the date of the solicitation.

LAWS AND REGULATIONS

US POSTAL SERVICE MANUAL

(Copies of the manual may be obtained frcrnthe Superintendent of Eocuments,US Government printing Office, Washington, DC 20402.) ●

2


MIL-C-12226G

2.2 Other publications. The following document(s) form a part of thisspecification to the extent specified herein. Unless otherwise specified, theissues of the documents which are DOD adopted shall be those listed in theissue of the mDISS specified in the solicitation. Unless otherwisespecified, the issues of documents not listed in the DODISS shall be the issueof the nongovernment dccuments which is c~rent on the date of thesolicitation.

NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., AGENT

Na t i o n a l Motor Freight Classification

.(Applications for copies should be addressed to the American TruckingAssociation, AlIll?: Traffic Department, 1616 P Street, N.W., Washington, EC20036).

UNIFORM CLASSIFICATI(I!COMMITTEE, AGENT

Uniform Freight Classification

(Applications for copies should be addressed to the Uniform ClassificationCcnunittee,Ram 1106, 222 South Riverside Plaza, Chicago, Illinois 60606).

DEPARTMENT OF DEFENSE STANDARD COLOR CARD OF OFFICIALSTANDARDIZED SHADES FOR SEWING THREAES

(Applications for copies may be obtained frcm the Color Association of theUnited States~ 24 East 38th St~ New York~ N.Y. 10016)

2.3 Order of Precedence. In the event of a conflict between the text ofthis specification and the references citedspecification shall take precedence. Nothing inshall supersede applicable laws and regulationshas been obtained.

3. REQUIREMENTS

herein, the text of thisthis specification, however,unless a specific exemption

3.1 Guide stnnple. Samples, when furnished, are solely for guidance andinformation to the contractor (see 6.3). Variations frcm this specificationmay appear in the sample in which case this specificationshall govern.

3.2 First article. When specified, the contractor shall furnish sampleunit(s) for first article inspection and approval (see 4.3 and 6.2).

3


MIL-C-12226G

3.3 Material.

3.3.1 Basic material. The b a s i c material for the cover shall be cottonbirdseye cloth, Olive Green Shade No. 107, conforming to Type 1, Class 3 ofCCC-C-425, except the residual shrinkage shall not exceed 10 percent in eitherthe warp or filling directions; the minimum absorption shall be 50 percent andthe only colorfastness requirements shall be colorfastness to laundering(after 3 cycles), perspiration, and crocking. Colorfastness to launderingshall be in accordance with FED STD 191, Test Method 5610. Samples shall bedried after each canplete laundering cycle and only the stain on the cottonfibers of the transfer cloth shall be evaluated.

*3.3.2 Ta~ , cotton. The tape for the cover shall be cotton herringbonetwill, 1/2 Inch wide, Olive Green Shade No. 107, conforming to Type 1, Class 3of DDD-T-86, except that only colorfastness to laundering shall apply.

*3.3.3 Thread. The thread for the seaing and stitching shall be cotton,ticket No. 50, 3 ply and ticket No. 70, 2 ply conforming to Type IA3 ofV-T-276. As an alternate~ polyester thread, ticket No. 50, 3 ply and ticketNo. 70, 2 ply, conforming to MIL-T-43548 may be substituted for the cottonthread. The color shall be Olive Drab Shade S-1, C.A. 66022.

*3.3.4 Label. Each cover shall have an identificationand instruction labelconforming to ~ VI, Classes 1 and 3 of DDD-L-20. The printing shall showcolorfastness to laundering. The label shall bear the following inscription:

COVER, TOXICOLOGICAL AGENTS PROTECTIVE GAS MASK HCX3D,COOLINGBASE FABRIC: 100%cO’rlmNcoNTRAcrNo: DLA-loo-oo-o-oooO(EXAMPLE)S’IW2KNO: 8415-00-000-0000 (EXAMPLE)NAME OF CONTRAC’IDR:NAME OF MFG: (if other than contractor)

INSTRUCTIONS

1. Wear over impermeable type hood for reduction of body heat stress.2. Keep soaked with water for maximum evaporative cooling effect.3. After use rinse throughly and hang up to dry.

IJWNDRY INSTRUCTIONS

Hand Wash ColdHang Dry

EO NOT REMOVE THIS LABEL

4

●

✎


MIL-C-12226G

O

.

●

●

3.4 Design. The cover is a loose fitti’~, slip over type, with face openingand tie-down tapes. (see figure 1).

3.4.1 Figure. Figure 1 is furnished for’information purposes only. Wheninconsistencies exist between the written specification and the figure, thewritten specification shall govern.

3.5 Patterns. Standard patterns to be used for cutting working patternswill be furnished by the Govermnent (see 6.3). The working patterns shall beidentical to the &wernment patterns and shall not be altered in any way. Thepatterns provide an allowance of 3/8 inch for regular seams. Unless otherwiseindicated in Table I all seams shall be in accordance with this seam allowance.

3.5.1 Pattern parts. The ccmponent parts shall be cut fran the materialspecified in accordance with the following patern parts.

Materials Ncnnenclatureof pattern parts cut parts

Cloth, birdseye Back panel A.

cotton Front panel 2

3.6 Construction.

3.6.1 Stitches, seams and stitching. Stitch, seam and stitching typesspecified in Table I shall conform to FEWSTE751. Whenever two or moremethods for seam or stitch types are given for the same part of the operationany one may be used. Seam allowance shall be maintained with seams sewn sothat no raw edges, runoffs, twists, pleats, puckers or open seams result. AI-1seams shall start and finish evenly. Thread tension shall be maintained sothat there is no tight or loose stitching. Where stitch type 401 is used, thelooper (underthread) shall be on the inside of the cover. Unless otherwisespecified, top stitching and edge stitching shall be 1/8 inch fran the foldededge.

3.6.2 Thread breaks and ends of seams. Ends of all seams and stitchingswhen not caught in other seams or stitchings shall be bartacked not less than3/8 inch. The ends of a continuous line of stitching shall be overlapped notless than 1/2 inch. Thread breaks (all stitch types) shall be secured bystitching back of break not less than 1/2 inch. Skipped stitches and threadbreaks may be repaired by using 301 stitch type.

3.6.3 Stitches per inch.inch shall be as specified in

The minimum and maximum number of stitches perTable I.

5


MIL-C-12226G

3.7 Manufacturing operations requirements. The cover shall be manufacturedin accordance with operation requirements as specified in table 1. The ocontractor is not required to follow the exact sequence of operations providedthe finished cover is identical to that provided by following the sequencelisted in Table 1.

3.7.1 Shade marking. The component parts shall be bundled.

3.7.2 Abbreviations in table of operations. The abbreviations used in TableI are as follows:

stch - stitchin inchndl - needlebob - bobbinlpr - loopermchne - machinebrtck - bartackCcmrcl - commercialsmlr - similarbtnhl - buttonholeincl - includingdbl - doublechnstch - chainstitch

.


O

.

@

o

MIL-c-12226G

TABLE I - CONSTRUCTION

NO. OPERATIQJ

1.

2.

3.

4.

5.

6.

7.

*tie ~verin strict accordance with

na++nrns , which shall show directional lines.-. .xkting and instructionsand notches forth~ n r n n e r a s s emb l v of all C c x n p o n e n t p a r t S .--- r .-r.- ———- -4

Replacementof defectivecanponentsDuring the spreading~ cutting andmanufacturing process, canponents havingmaterial defects that are classified asdefects in Section 4, shall be removed frcmproductionand replacedwith non-defectiveandproperlymatched components.

ShademarkingAll parts shall be bundled.

ConstructionThe cover shall be made of two plies of thebasicmaterial.

OF CWER

STCH sEAM/ STCH NDL BOB/TYPE SIKH TYPE IN LPR

Join panels of inside and outside covers

(singleply only)a. Join center seam of back panels. 301 or SSa-1 10-14

401

b. Join top center seam of frontpanel. 301 or SSa-1 10-14401

Assemble frontsand prepare face openingFOsition the two single plies of front 301 or SSe-2(a) 10-14

a.panel, face to face, with all seams matching 401

and seam around the face opening.

b . S l a s h s e a m allowance around face opening. 301 SSe-2(b) 10-14

Turn, work out edges, and single stitch aroundface opening 3/8 tool/2 inch frcm the edges.

Join frontand backa. Position both back panel plies, face toface, simultaneouslysandwichingthe ccmpletedfront panel.

b . Stitch thru all plies, joiningside seam. 301 or SSq-2(a)401

7

50 5050 70

50 5050 70

50 5050 70

50 50

10-14 50 5050 50


MIL-C-12226G

TABLE I - CCXWYIRUCTION

No. OPERATICN

c. Turn to finished position and topstitchside and center seams 1/8 inch frcm foldededge.

8. Hem bottcm and attach labela. Finish the bottcm circumferenceof coverby turning in both plies 1/4 inch andedgestitching1/8 inch frcm folded edge whilecatching label. Labelinsideof the cover.

b. Stitch label across3/16 inch fran edge.

OR

shall finish on the

top and sides 1/8 to

c. Stitch all four sides of label to insideof back panel adjacentto the side seam.

90 Tie tapesa. There shall be three tie tapes eachmeasuring7 (~ 1/2) inchescut length.

b . Attach two tie tapes with a 1/2 inch longbacktack, straight tack or bartack at centerof tapes on inside of cover as indicatedbypatternmarks. Attach the third tie tape witha 1/2 inch long backtackr straight tack orbartack at center of tape on inside of coverat center crown seam. Tapes shall finish 31/2 (~ 1/4) incheslong.

10. Clean covera. TYim all ends and remove all loosethreads.

OF COVER

THREADSTCH sEAM/ STtM NDL BOB/TYPE STCH TYPE IN LPR

301 or SSq-2(b) 10-14 50 70401

301

301

301

50 70

Ssp-1 10-14 50 50

.

LSbj-1 10-14 50 50

LSbj-1 10-14 50 50

301 or304 orbartack

10-14 50 5010-14 50 5028 per 50 50bartack

b. Remove all spots and stains.

8


MIL-C-12226G

●

J

.

●

o

3.8 Measurements. The finished cover shall confozm to the measurementsshown in Table II.

Table II - Measurements of cover (inches)

Measurements Tolerance

1/2 Bottcm opening (A) 26. + 3/4Center seam (back) (B) 26 1/2 T 3/4Center front (C) 10 1/2 T 3/4Side seam (D) 21 1/4 T 3/4

(A) Bottom opening - Fold bottan in half and measure along the bottcxnedgefrcrnfolded edge to folded edge.(B) Center seam - Fran top of face opening across top cover to bottan edge ofback.(C) Center front - Fold front, side seam on side sew and measure along foldfront bottcm of face opening to bottcm edge of cover.(D) Side seam - Fran bottcm edge to center seam at top of cover.

3.9 Workmanship. The finished cover shall conform to the quality of productestablished by this specification. The occurrence of defects shall not exceedthe applicable acceptable quality levels.

4. QUALITY ASSURANCE PROVISIONS

4.1 Responsibility for inspection. Unless otherwise specified in thecont~act, the contractor is responsible for the performance of all inspectionrequirements as specified herein. Except as-otherwise specified ‘in thecontract or order, the contractor may use his own or any other facilitiessuitable for performance of the inspection requirements specified herein,unless disapproved by the Government. The Government reserves the right toperform any of the inspections set forth in the specification where suchinspections are deemed necessary to assure supplies and services confom toprescribed requirements.

4.1.1 Responsibility for canpliance. All items must meet all requirementsof sections 3 and 5. The inspection set forth in this specification shallbeccme a part of the contractor’s overall Inspection system or quality prcgram.The absence of any inspection requirements in the specification shall notrelieve the contractor of the responsibility of assuring that all products orsupplies submitted to the Government for acceptance canply with allrequirements of the contract, Sampling in quality conformance does notauthorize suhnission of known defective material, either indicated or actual,nor does it ccxmnitthe Goverrnnentto acceptance of defective material.

4.1.2 Certificate of ccrnpliance. Where certificates of ccxnpliancearesubmitted, the Government reserves the right to check test such items todetermine the validity of the certification.


MIL-C-12226G

4.2 Classification of inspection. The inspection requirements specifiedherein are classified as follows: o

1. First article inspection (see 4.3).2. Quality conformance inspection (see 4.4).

4.3 First article inspection. The first article sulxnittedin accordancewith 3.2 shall be inspected as specified for canpliance with design,construction? workmanship and dimensional requirements.

4.4 Quality conformance inspection. Sampling for inspection shall beperformed in accordance with MIL-STD-105, except where otherwise indicated.

4.4.1 Component and material inspection. In accordance with 4.1 above,components and materials shall be tested in accordance with all therequirements of referenced specifications~ drawings, and standards unlessotherwise excluded? amended~ modified? or qualified in this specification orapplicable procurement docunents.

4.4.2 Examination of the end item. Examination of the end item shall be inaccordance with 4.4.2.1 through 4.4.2.2. The applicable inspection levels andacceptance quality levels (AQL’s) shall be as indicated in 4.4.2.3. The lotsize shall be expressed in units of covers. The sample unit shall be onefinished cover.

10


MIL-c-12226G

4.4.2.1 Visual examination. The cover shall be visually examined for thefollowing defects:

Classificat~Defect Major Minor

MATERIAL DEFECI’SAND t@RKMANSHIP DAMAGES

a .

b.

c.

d.

e.

Hole, cut, tear, smash, scorched area,drill hole ormopen place:1. On outside (longestdimension in

(a) - up to 1/4 inch, inclusive(b) - more than 1/4 inch

2. On inside, any

a n y direction):

Misweave, area of no dye penetration, needle chew,thin place, visable mend, missing yarn or brokenyarn, more than 1/2 inch (largest dimensions in anydirection):-On outside

Knot on outside, when larger than the limit shownfor knots on figure 1 of FED-STD-4

Permanent fold, pleat or crease in cloth (when caughtin seaming or stitching):-On outside

Loose yarn, snagged thread, coarse yarn or woven inwaste; more than 1 inch (largest dimension in any.. .. .alrectlonj:-On outside

COMPONENT AND ASSEMBLY

a.

b.

c.

d.

Any ccmponent part or operation anitted (unlessotherwise classified herein)

xx’

x

x

x

x

x

“x

my canponent not as specified (type, color, size, etc.) X

Any ccxnponentpart noticeably twisted, distorted orpuckered, affecting appearance x

Any operation”notas specified (unless otherwiseclassified herein) -

CUTTING

a . An y canponent part not cut inpattern, directional lines onrequirements.

x

accordance with specifiedpatterns or specification

x

11


MIL-C-12226G

ClassificationDefect Major Minor

CLEANLINESS

a. my non-removable spot or stain on outside, clearlynoticeable and affecting appearance

b. More than 3 thread ends not trinnnedto 1/4” or less onoutside

SEAMS AND STITCHING

a.

b.

c.

d.

e.

Accuracy of seaming1. Part of cover caught in any unrelated stitching

operation x2. seam noticeably puckered, twisted, or pleated,

affecting appearance or serviceability3. End of stitching not caught in another seam or

stitching backpacked less than 3/8 inch4. Ends of a continuous line of stitching overlapped

less than 1/2 inch5. Stitching overlapping ends of thread break less

than 1/2 inch6. Shade of thread used on outside not as specified7. Needle perforations visable on outside

Stitching margin1. Irregular or not within specified range or varies

more than 1/8 inch when no range is specified(score only when the condition exists on more than1/2 the length of the seam)

2. Edge or top stitching sewn tco close to edge,resulting in serious damage to cloth x

Seam allowance Width not as specified by more than1/16 inch (score only when condition exists on morethan 1/2 the length of seam)

Open seam (Skipped or broken stitches)1. On outside

(a) Less than 3/4 inch(b) 3/4 inch or more

2. On inside- 3/8 inch or more

Runoff1. On joining seams, score as open seam2. Edge or top stitching - more than 1/4 inch

x

x

x

x

x

x

xxx

x

x

x

x

12


●

o

●

MIL-C-12226G

ClassificaGDefect Major Minor.f.

h.

i.

Raw edges1. On outside

(a) Less than 3/4 inch(b) 3/4 inch or more

2. On inside3/4 inch or more

Seam and stitch types (“.

1. Not specified seam or stitch type2. Looper thread on outside (when 401stitch is used)3. Any line of stitching anitted4. Any line of stitching not beginning or ending

where specified

Stitch tension1. Loose tension resulting in loosely exposed loops

of lower or top thread (score only when conditionexists on more than 1/2 length of seam)(a) Affecting serviceabilityor appearance,

seriously(b) Affecting serviceabilityor appearance,

not seriously2. Tight tension (stitchesbreak when normal strain

is applied in the seam or stitch direction)

Stitches per inch (to be scora only when the conditionexists on more than 1/2 the length of seam or stitching)1. More than the maximum specified2. TWO or nioreless than the specified minimum

Bartack, backtack or tack missing, misplaced, insecure,not serving the intended purpose or not specified sizeor type

TIE TAPES

a. Misplaced or insecure

b. End of finished tape less than 3-1/4 inches or more than3-3/4 inches long

xx“

“x

., xx

x

x

x

x“

x

x‘x

x

x

x


MIL-C-12226G

Classification ●Defect Major Minor

IDENTIFICATION LABEL

a. Cmitted, incorrect or illegible x

b. Not attached as specified x

c. Misplaced or stitching through printing x

4.4.2.2 Dimensional examination. My measurement deviating from thedimensions and tolerances specified in Table II shall be scored as ameasurement defect.

4.4.2.3 Inspection levels and acceptable quality levels. The inspectionlevels and acceptable quality levels (AQL) expressed in defects per 100 units,for visual and dimensional examinations shall be as follows:

AQL Inspection Level

For visual examination in 4.4.2.1 6Major 2.5 IITotal (major & minor ccxnbined) 15.0 II

For dimensional examination in 4.4.2.2.Orieclass 4.0 s-3

4.4.3 Examination of packaging requirements. An examination shall be madeto determine that packaging, packing, and marking comply with Section 5requirements of this specification. Defects shall be scored in accordancewith the list below. The sample unit shall be one shipping container fullyprepared for delivery. Defects of closure listed below shall be examined onshipping containers fully prepared for delivery. The lot size shall be on thenumber of shipping containers in the end item inspection lot. The inspectionlevel shall be S-2 and the AQL shall be 2.5 defects per hundred units.

14


MIL-C-12226G

Examine Defect

Marking (exterior CYnitted,incorrect, illegible,of improper.size,and interior location, sequence, or method of application.

Materials Any ccinponentmissing, damaged, or not as specified.

lbrlunanship Inadequate application of canponents, such as:’incomplete closure of container flaps, loosestrapping, improper taping, inadequate stapling,bulged or distorted container.

“Content Number of’items per shipping container is more orless than re@ired. Size shown on one or moreitems not as specified on shipping container.~/

1/ For this defect, two shipping containers in the sample shall be exmined.

4.4.4 Palletization examination. An examination shall be made to determinethat the palletizati,onccmplies with the section 5 requirements. tkfects shall ,be scored in accordance with the list below. The sample unit shall be onepalletized unit load fully packaged. The lot size shall be the number ofpalletized unit loads in the end item inspected lot. The inspection levelshall be S-1 and the AQL, expressed in terms of defects per hundred units,shall be 6.5 in accordance with MIL-STD-105.

Examine Bfect

Finished dimensions Length, width,or height exceeds specified maximumrequirements.

Palletization Pallet pattern not as specified.Interlockingof loads not as specified.Load not bonded with required straps as specified.

Weight

Marking

Exceeds maxinuxnload limits.

~itted, incorrect, i~legible,of improper size,location, sequence, or method of application.

5. PACKAGING

5.1 Preservation packaging. Packaging shall be level A or C as specified(see 6.2).

15


MIL-C-12226G

5.1.1 Level A. Each cover shall be folded as

a. EY cover flat with face openi.nqUP.

follows:

b. Fo~d in half by bringing tfietop t~ the bottan of the cover.c. Fold in the left and right sides of the cover base so that the cover

is rectangular in shape.do Fold in half again by placing one side on top of the other side so

that the folded cover measures approximately 7 1/2 inches by 11 1/2iriches.

Each cover shall be inserted into a snug-fitting clear polyethylene bag of0.00125 (~ 20 percent tolerance) thickness. Ml seams and closures shall beformed by heat sealing. A 1/4 inch maximun diameter hole shall be made at one -corner of each bag to allow excess air to escape. Alternatively, thepolyethylene bag may be the tuck-in overlap type, in which a heat seal closureand vent hole are not required.

5,1.2 Level C. Covers shall be packaged to afford adequate protectionagainst physical damage during shipnent frcrn the contractor to the firstrecieving activity. The package and the quantity per package shall be the sameas that normally used by the contractor for retail distribution.

5.2 Packing. Packing shall be level A, B or C as specified (see 6.2).

5.2.1 Level A. One hundred covers, packaged as specified in 5,1.1, shall bepacked flat, two in length, two in width, and twenty-five in depth in afiber-board shipping container assembled, closed and reinforced conforming to atype CF, class weather resistant, variety DW, grade V15C, size 3A, ofMIL-B-17757. The fiberboard used for the liner shall conform to type CF, classdcxnesticconforming to MIL-B-17757.

5.2.2 Level B. One hundred covers packaged as specified in 5.1.1. shall bepacked flat, two in length, two in width, twenty-five in depth in a fiberboardshipping container~ assembled~ closed and reinforced conforming to type CF,class dcxnestic,variety DW, grade 275, size 3A, of MIL-B-17757. The fiberboardused for the liner shall conform to type CF, class danestic of MIL-B-17757.

5.2.3 Level C. Item packaged, as specified in 5.1, shall be packed in amanner to insure carrier acceptance and safe delivery at destination at thelowest transportation rate for such supplies. The quantity per shippingcontainer shall be the sane as that normally used by the contractor for retaildistribution. Containers shall canply with the US Postal Service Manual,Uniform Freight Classification Rules or National Motor Freight ClassificationRules, as applicable.

16


MIL-C-12226G

5.3 Marking. In addition to any special marking required by the contractor order, interior packages and shipping containers shall be marked inaccordance with MIL-S’TE129.

5.3.1 Polyethylene mgged packages. Polyethylene packaged covers shall havethe following information legibly printed or stamped in black directly on thebag or on a white paper label inserted within the bag so as to pennit readyidentification:

Stock NunberNanenclatureQuantity

5.4 Palletization. When specified (see 6.2) item packed as specified shallbe palletized on a 4-way.entry pallet in accordance with load type IA ofMIL-STD-147. Each prepared load shall be ‘bondedwith primary and secondarystraps in accordance with bonding means C, K, and L or O or P. Pallet patternshall be in accordance with the appendix of MIL-STD-147.

The pallet shall be 4-way, Type IV, V, Class 1, Size 2; or Type VIII,fabricated from wood group I, II, III or IV, Grade A of NN-P-71, or 4-way,Style 1, Size A, Type 1, Class 1 fabricated frcnnwood groups specified, ofMIL-P-15011. Interlockingof loads shall be effected by reversing the patternof each course. If the container is of a size which does notof the patterns specified in MIL-s~147, the pallet patternapproved by the contracting officer.

6. ms

conform to anyused shall be

6.1 Intended Use. The cover is intended for use over the gas maskprotective hood of the M-3 as a supplementarygarment for cooling purposes.

6.2 Ordering data. Procurement documents should specify the following:

a. Title, nmber and date of this specification. *

b. men a first article sample is required (see 3.2 and 4.3), the itemshall be tested and should be a first article sanple. Thecontracting officer should include specific instructions inacquisition dcxmnents regarding arrangements for examinations inquantity, and testing and approval of the first article.

c. Applicable levels of packaging and packing. (see 5.1 and 5.2)d. men palletization is required. (see 5.4)

6.3 Samples and patterns. For access to samples and patterns, address theprocuring activity issuing the invitation for bids. (see 3.1 and 3.5)

17


MIL-C-12226G

6.4 Recycled materials. Use of recycled materials is encouraged as long asit meets the requirements of this specification.

6.5 Subject term (key word) listing:Cloth, birdseye cottonCover, gas ma s kHo d , w a t e r c o o l i n gP r o t e c t i v e , t o x i c o l o g i c a l a g e n t

6.6 Changes frcm previous issue. The margins of this specification aremarked with an asterisk to indicate where changes (additions, modifications,corrections, deletions) frcn the previous issue were made. This was done as aconvenience only and the Government assumes no liability whatsoever for anyinaccuracies in these notations. Bidders and contractors are cautioned toevaluate the requirements of this document based on the entire contentirrespective of the marginal notations and relationship to the last previousissue.

Custcdian: Preparing Activity:Navy - NU Navy - NUAir Force – 99

Review Activity: Project No. 8415- 0524DLA-CT

User Activity:Navy - OS, MC

18

.

?


MIL-C-12226G

FIGURE 1 - COVER,TOXICOLOGICALAGENTS PROTECTIVEGAS MASK HOOD, COOLING

19


STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSAL(SeeInstructions- ReverseS~)

. OOCUMENT. NUMBER 2. DOCUMENT TITLE

MIL-C-12226G COVER. TOXICOlf)~TSlaNAME OF SUBMITTIIW ORGANIZATION 4. TYPE OF 0RGANt2AT10N (Marh one)

n VENOOR

n USER

, ADDRESS (StrwtoCity. 8tst#.ZIP Code)

❑ MANUFACTURER

cl_OTHER (Speciti):

. PROBLEM AREAS

a Porwwph Number and WordIn@:

b. Raomrnandod Wording:

c. Roaon/R~tionolo for RuomrnondatMr:

REMARKS,,

l. ’

a . NAME OF SUBMITTER fhta FtiL MI) - Opthnal ‘. b. WORK TELEPHONE NUMSER (hcfu~ ArwC*) - Optlorul

MAILIN~ A~ORESS (Stmek Cf&, State, ZIP Codd - Optional S, DATE OF SUBMISSION {YYMMDD).,, ,,, ,, .

... ,,,

.~. . :

nn . . . . . A .--

9

lJIJ &“MTR 14ZU P~lEVIOW EDITION IS OESOLETE.


Documents

MIL-C-12226G - SUPERSEDING MIL-C-12226F 28 …everyspec.com/MIL-SPECS/MIL-SPECS-MIL-C/download.php?...MIL-C-12226G 3.3 Material. 3.3.1 Basic material. The bas i c material for the