Master Safety New Tex

8/2/2019 Master Safety New Tex

1/16

THE HIGHTEMPERATURE

ADVANTAGE

2000F1093C

SAFETY PRODUCTS CATALOGSAFETY PRODUCTS CATALOG


2/16

Page Contents

1 to 2 Technical Information3 to 6 High Temperature Gloves and Mitts

7 to 10 High Temperature Fire Entry, Kiln, Proximity, andApproach Suits; Hoods and Accessories

11 to 12 Aluminized Safety Clothing

13 to 14 High Temperature Safety Blankets and Curtains

Table of Contents

Newtex Industries manufactures Zetex, a heat resistant fabric that provides

protection up to 1100F (593C) and ZetexPlus, a proprietary heat resistant fabricthat can withstand temperatures up to 2000F (1093C).

Zetex and ZetexPlus are proven, time-tested textiles: Zetex products are usedfor applications up to 1100F (593C) and ZetexPlus products are used forapplications to 2000F (1093C). Materials have an average K-value of0.3399 BTU/inch/hr/sq ft/F.

Zetex and ZetexPlus are not only high temperature resistant, but can alsowithstand cold temperatures to -100F (-73C).

High dielectric strength and low constant of 5.9 to 6.4.

Zetex and ZetexPlus fabrics are chemical resistant ~ resisting most acids, alkaliesand solvents. The fabrics are also mildew resistant.

Most fabrics are made from durable texturized amorphous silica yarns that aretwice as strong as steel wire of same diameter.

Expanded line of coated fabrics have low smoke emissions and are designedfor fabrication.

Aluminized Zetex fabric reflects 90% of radiant heat.

Wide selection of safety products and fabrics.

Fabrics are UL listed and exceed European EN407 industrial standards.

Made in USA.

THE HIGH TEMPERATURE ADVANTAGE

Kevlar and Nomex are registered trademarks of E.I. duPont, Inc. PBI is a registered trademark of Celanese Corporation. Vortex is a registered trademarkof Vortec Corporation. Velcro is a registered trademark of Velcro USA, Inc.

UP TO 1100F (593C) UP TO 2000F (1093C)

Zetex and ZetexPlus products are high temperature products designed for specific industrial and safety applications. The buyer should

carefully consider the use for which Zetex and ZetexPlus products are purchased for. The buyer assumes all risk and liability associated with their use.Zetex and ZetexPlus products are warranted against defects and workmanship for 30 days.


3/16

ZetexPlus fabric can withstand temperatures of up to 2000F(1093C) and resists burn-through by a continuous flame.In this test, the temperature of the fabric on opposite side offlame is only 179F (82C) with a probe only 1 inch from flame.

Using a ZetexPlus double palm mitt, a worker can hold a3.75 pound (1.7 Kg) pipe heated to 2000F (1093C) for upto 20 seconds.

TemperatureRise

Time (seconds)

Aluminized asbestos

40

30

20

10

01 2 3 4 5 6 7 8 9 10

Aluminized fiberglass

Aluminized Zetex

104

86

68

50

CF

KValue

Mean Temperature (F)

ZetexPlus 2200

1.1

1.0

0.9

0.8

0.7

0.6

0.5

0.4

0.3

100 200 300 400 500 600 700 800 900 1000 1100-100 0

Zetex 2200

Zetex 800

UP TO 1100F (593C) UP TO 2000F (1093C)

Aluminized Zetex fabric

outperforms other fabrics

Zetex and ZetexPlus ThermalConductivity Vs. Mean Temperature

The temperature ofAluminized Zetex fabricremains lower than otherfabrics in moltenmetal splash test.

UL UL ListedULListed

Zetex and ZetexPlus fabrics meet orexceed one or more of the followingspecifications:

s UL 214 and

NFPA Spec No 701

s UL 723 Flame Spread is 0, Smoke

Density is 0, Fuel Contributed is 0

s US Coast Guard Spec No 164.009s US Military Spec MIL-C-20079

s US Military Spec MIL-I-24244 and

NRC 1.36 Spec

s European BS EN407 standards

s UBC 43-1, NFPA 252, and

California State Fire Marshall


4/16

HIGH TEMPERATURE SAFETY GLOVES AND MITTS

Choice of durable Zetex and ZetexPlus fabrics for specific high temperature applications.Use Zetex gloves up to 1100F (593C) and ZetexPlus gloves up to 2000F (1093C)

Custom Fabrication Available

Functional fit; standard size fits most hands. Also haveladies size for smaller hands

Choice of gloves, double palm gloves, mitts, doublepalm mitts, and overmitts. All mitts are reversible

3 standard lengths available: 11", 14" and 23"

Durable cotton-backed 11 ounce wool liner sewnat fingertips

Kevlar thread is double-stitched in all areas forstrength and durability

Use leather, Kevlar, Blended Kevlar or PBI/Kevlar

palms for abrasion and cut resistant uses

Use Aluminized Zetex for radiant heat protection

Easy ordering and quick shipments

Zetex and ZetexPlus gloves and mitts can be custom

fabricated to your specifications

Made in USA

F E A T U R E S

UP TO 1100F (593C) UP TO 2000F (1093C)

Application Fabric Type

Zetex ZetexPlus Zetex & ZetexPlus Zetex & ZetexPlus Aluminized Zetexwith leather with Kevlar Aluminized Kevlarreinforced palm reinforced palm Aluminized Nomex

Aluminized Rayon

Page 4 Page 4 Page 5 Page 5 Page 6

High Temperature

up to 1100F (593C) s

up to 2000F (1093C) s

Low Temperature

to -100F (-73C) s s

High Abrasion Resistance

up to 600 to 800F (316 to 427C) s s

Cut Resistance

up to 600 to 800F (316 to 427C) s s

Radiant Heat Protection s

Molten Metal Splash Protection s

APPLICATION GUIDE


5/16

GUIDE

Type Lengths* Lengths*

9" 11" 14" 23" 9" 11" 14" 23"

Standard Size Glove s s s s s sLadies Size Glove s s s s s s

Standard Size Mitt s s s s s s

Double PalmStandard Size Glove s s s s

Reversible Double PalmStandard Size Mitt s s s s

Standard Size Overmitt s s

*Metric length equivalents: 9" = 229mm; 11" = 279mm; 14" = 355mm; 23" = 584mm

Zetex standard size gloves are available in 3 lengths: 11", 14", and 23". Also in smaller ladies size

Zetex and ZetexPlus mitts are available with single or

double palm. ZetexPlus 14" double palm mitt shown

Zetex double palm glove in 14" length. Also available inZetexPlus fabric

Hand pads come with Zetex fabric or

Zetex fabric with leather palm (shown)

Finger cots are shipped in package

of 12

Zetex overmitt in 9" length in singleor double palm (shown)

High Temperature Protection

SAFETY GLOVES AND MITTS

Custom Fabrication

Available

Zetex and ZetexPlus gloves and mitts provideexcellent protection for high temperature applications

ZetexPlus gloves are available in

11", 14" (shown), and 23" lengths.Also in ladies size

UP TO 1100F (593C) UP TO 2000F (1093C)

ZETEXPLUSZETEX


6/16

GUIDE

Type Ladies Size* Standard Size*

14" 23" 14" 23"

Zetex Glove with Kevlar,

Blended Kevlar orPBI/Kevlar Palm s s s s

Zetex Glove withLeather Palm s s s s

ZetexPlus Glove withZP Kevlar Palm s s s s

ZetexPlus Glove withZP PBI/Kevlar Palm s s s s

Zetex Mitt with Kevlar,Blended Kevlar orPBI/Kevlar Palm s s s s

Zetex Mitt with Leather Palm s s s s

ZetexPlus Mitt withZP Kevlar Palm s s s s

ZetexPlus Mitt withZP PBI/Kevlar Palm s s s s

Blended Kevlar Glove s s s s

Blended Kevlar Mitt s s s s

*Metric length equivalents: 14" = 355mm; 23" = 584mm

High Abrasion Protection



Zetex 14" glove with Kevlar palm ZetexPlus 14" glove withZP Kevlar palm

Zetex 23" mitt with PBI/Kevlar palmBlended Kevlar glove available in 2sizes and 2 lengths (shown in 14"

length)

Double Palm Mitt

tested at 1800F (982C)

ZETEX

ZETEXPLUS

KEVLAR

25

20

15

10

5

0

Seconds

Average Time (seconds) worker holds a 3.75 lb. (1.7 Kg) hot pipe

Single Palm Mitt

tested at 1100F (593C)

ZETEX ZETEXPLUS

KEVLAR

Zetex and ZetexPlus products with leather and Kevlar

reinforced palms provide excellent abrasion and cut protection.

Maximum temperature range is 600 to 800F (316 to 427C)

Zetex and ZetexPlus outperform Kevlarmaterial in high temperature applications

UP TO 1100F (593C) UP TO 2000F (1093C)

Zetex 14" mitt with leather palm Zetex 14" glove with leather palm

At 1800F (982C),Kevlar materialundergoesinstant

combustion


7/16


Radiant Heat Protection


Aluminized Zetex 14" glove with aluminized back Zetex All Aluminized 14" glove Zetex All Aluminized 14" mitt

FAA approved glove: Aluminized Kevlar 14" glove with leather palm, vaporbarrier, gauntlet style. Also available in knit-wrist style (shown at right)

Aluminized PBI/Kevlar (left) and Aluminized Zetex (right) 14" glove withleather palm, gauntlet style. Also available in Aluminized Nomex, Kevlar,

and Rayon. Knit-wrist style available

Aluminized Zetex gloves and mitts are made with metalizedaluminum film bonded to durable Zetex fabric. They provideexcellent insulation, flexibility, radiant heat protection, andresistance to delamination, cracking, and peeling.

For high heat and reflective heat protection, use Aluminized Zetex

glove or mitt with ZetexPlus palm

Aluminized Zetex fabric is designed toreflect 90% of the radiant heat

UP TO 1100F (593C) UP TO 2000F (1093C)

GUIDE

Type Ladies Size* Standard Size*

11" 14" 23" 11" 14" 23"

Zetex All Aluminized Glove s s s s s s

Zetex All Aluminized Mitt s s s s s s

Aluminized Zetex Glove with

Zetex Palm s s s s s s

Aluminized Zetex Glove withZetexPlus Palm s s s s s s

Aluminized Zetex Mitt with

Zetex Palm s s s s s s

Aluminized Zetex Mitt withZetexPlus Palm s s s s s s

FAA Approved Glove:Aluminized Kevlar with leather

palm, vapor barrier, gauntletstyle or knit-wrist style s s

Aluminized Zetex glove with

leather palm. Also availablewith Aluminized PBI/Kevlar,

Nomex, Kevlar, and Rayon s s

*Metric length equivalents: 11" = 279mm; 14" = 355mm; 23" = 584mm


8/16

THEULTIMATETESTFierce, yellow-orange flames

of blazing jet fuel lashed the

morning skies as a Rochester,NY firefighter prepared for abreathtaking demonstration.He was about to walk directlythrough the heart of a 2500F

inferno. His only protectionwas a 2000 Series Fire EntrySuit made with ZetexPlus fabric.

1. Temperature monitor strips(Omega label at 110F (43C),120F (49C), and 140F (60C)

ranges) were applied to criticalareas of firefighters clothing.

2. Similar monitor strips wereapplied to the fire suit.

3. The walk took place in a lanebetween two 71/2 feet high (2.3meters) by 12 feet long (3.6meters) stacks of hardwood palletssoaked with 30 gallons (120 liters)of aviation jet fuel and ignited using5 gallons (20 liters) of gasoline.

4. Entering the flame lane at the

height of the blaze, the firefighterwalked the length of the fire andback four times ~ a total of 96 feet(29 meters). He was engulfed inflames where the heat reached2350F to 2500F (1288C to1371C).

5. Immersed in the inferno, thefirefighters temperature monitorson his clothing reached only 110F(43C) except on his left arm andchin where the temperatures were120F (49C). The time of the firewalk was one minute; the firefight-er was inside the fire suit for 3 to 4minutes.6. The exterior of the suit wasonly blackened by the smoke andflames.

7. The interior of the fire suit wasunaffected by the fire.


9/16

Newtex technologyhas developed acomplete line of

high temperatureprotective suits.

These protective suits meet the mostdemanding requirements for hightemperature applications.

They are available as complete suit(hood, coat, pants, boots, gloves ormitts) or as individual items.

ALWAYS have 2 people suited with

fire entry, kiln, and proximity suitsto work in relays and aid each other.

2000 Series Fire Entry Suit

Description: ZetexPlus fabric plus 7 more layersof insulation for maximum heat protection.

Breathing apparatus required.Hood: Designed to be used with air mask.Inner drape flame seals. Underarm adjustmentstraps. Built-in shell for structural support. Hardcap with ratchet headgear. Speedy clip for hardcap support. Hardened aluminum window framewith 2 tempered glass lenses plus 2 gold platedlenses for thermal protection.

Coat: Designed to be worn with breathingapparatus. Double storm fly front. Flame sealwith drawstring at coat bottom.

Pants: High waist design. 2 inch wide adjustablesuspenders. Adjustable straps on leg bottoms.

Boots: Designed to fit over work shoes. Rear

entry with overlap snap closure and adjustabletake-up straps. Insulated wire reinforced sole offlame resistant neoprene fiberglass riveted toboot cover. All straps and bindings are ZetexPlus.

Mitts: Heavyweight construction made withZetexPlus fabric.

Weight: 48 pounds (22 kg).

Application: Use where high heat protection isneeded. Designed for short duration ambientheat 1500F (815C), radiant heat to 2500F(1371C), and total flame 2000F (1093C).



HIGH TEMPERATURE PROTECTIVE SUITS


Description: Aluminized Zetex plus 7 morelayers of insulation for maximum heat

protection and radiant heat protection.Breathing apparatus required.

Hood: Designed to be used with air mask. Innerdrape flame seals. Underarm adjustment straps.Built-in shell for structural support. Hard capwith ratchet headgear. Speedy clip for hard capsupport. Hardened aluminum window framewith 2 tempered glass lenses plus 2 gold platedlenses for thermal protection.

Coat: Designed to be worn with breathingapparatus. Double storm fly front. Flame sealwith drawstring at coat bottom.


Boots: Designed to fit over work shoes. Rearentry with overlap snap closure and adjustabletake-up straps. Insulated wire reinforced sole offlame resistant neoprene fiberglass riveted toboot cover. All straps and bindings areZetexPlus.

Mitts: Heavyweight construction made withZetexPlus fabric.

Weight: 54 pounds (25 kg).

Application: Use where high heat protection andradiant heat protection is needed. Designed forshort duration ambient heat 1500F (815C),radiant heat to 3000F (1650C), and total flame2000F (1093C).

UP TO 1100F (593C) UP TO 2000F (1093C)

SAFETY FIRST

Know What Type ofProtection is Needed

Ambient Heat is the heat (or temperature)

of the surrounding air.Example:the air temperature in a factory

setting is 100F (38C)

Conductive Heat is heat transferred as a resultof direct contact with a heat source.

Example: in the same factory setting, the

temperature of a hot water pipe is 160F (71C)

Radiant Heat is heat absorbed by objectsstruck by heat energy rays.

Example:the radiant heat from the hot waterpipe is 160F (71C) next to the pipe; the

radiant heat from the hot water pipe decreases

as one walks away from the hot water pipe


10/16

SAFETY FIRST Ambient Temperature Application Guideline

Short time period durationsDegrees F Degrees C Type of Protective Suitup to 200 up to 93 150 Series and 550 Series

200 to 350 93 to 177 150 Series with quilted Nomex or Wool liner550 Series with quilted Nomex or Wool liner

350 to 550 177 to 288 750 Series550 to 800 288 to 427 850 Series

All Zetex Aluminized Protective Suits can withstand radiant heat up to 2000F (1093C)

150 Series/550 Series Approach Suit

Description: 150 Series:non-insulated suit withAluminized Zetex outer shell plus a flame retardantcotton lining for extra comfort and protection.

550 Series:Same as 150 Series except with avapor barrier lining of flame retardant neoprene

coated FR poly-cotton.Aluminized Kevlar, Nomex, or PBI/Kevlar are alsoavailable as outer shell fabrics. Wool or quiltedNomex linings are available.

Hood: Designed like proximity hood with built-inshell for structural support. Hard cap with ratchetadjustment. Speedy clip for hard cap support. Fulllength drape is not insulated.

Coat: Tailored sleeves with snap adjustment.Covered front snaps. Available with or withoutbreathing apparatus accommodation.

Pants: High waist design. 8 point all elasticadjustable suspenders. Snapped triangular stormfly front. Snap adjustment on leg bottoms.

Boots:Designed to fit over work shoes. Leathersoles and heels. Adjustment tightening straps.

Gloves: Gauntlet style with leather palms. S.E.F.lining in fingers.

Applications: Industrial and factory applicationswhere temperatures do not exceed 200F (93C).

850 Series Kiln Suit

Description: Highly insulated suit with AluminizedZetex fabric outer shell and internal vapor barrier.Breathing apparatus required.

Hood: Designed to be used with air mask.Inner drape flame seals. Underarm adjustment

straps. Built-in shell for structural support. Hardcap with ratchet headgear. Speedy clip for hardcap support. Hardened aluminum window framewith 2 tempered glass lenses plus 2 gold platedlenses for thermal protection.

Coat: Designed to be worn with breathing appara-tus. Double storm fly front. Flame seal drawstringat coat bottom.

Pants: High waist design. 2 inch wide adjustablesuspenders. Adjustable straps at leg bottoms.

Boots: Designed to fit over work shoes. Heavyinsulated upper boot cover with zipper and stormfly. Adjustable tightening straps. 1 inch woodensole with anti-skid bottoms. Inside leather toe andankle adjustable straps. ZetexPlus binding.

Mitts: ZetexPlus palm and thumb. Aluminizedback and cuff.

Applications: Used for maintenance and repairapplications.

750 Series Proximity Suit

Description: Insulated suit with Aluminized Zetexfabric outer shell and double vapor barrier.Breathing apparatus recommended.

Hood: Full shoulder length drape. Adjustableunderarm straps. Built-in shell for structural sup-

port. Hard cap with ratchet adjustment. Speedyclip for hard cap support. 6" by 91/4" gold windowand aluminum retainer. Two side wing locks forholding lens and retainer in place.

Coat: Available with or without breathing appara-tus accommodation. Double storm fly front.Flame seal with drawstring at coat bottom.


Boots: Designed to fit over work shoes. Leatherinsulated soles. Adjustable tightening straps.ZetexPlus binding.

Mitts: ZetexPlus palm and thumb. Aluminized backand cuff.

Applications: Used for maintenance and repairapplications where there is steam or volatile mate-rials present.

850 Series Kiln Suit ~ 750 Series Proximity Suit ~ 150/550 Series Approach Suit



11/16

Vortex

cooling system designed for high tempera-ture applications to keep worker comfortable

Aluminized Zetex welding hoodAluminized Zetex lift front hood

Nomex hood

Retainer, gold film, clear lens

Zetex has a complete line of hoods and accessories available

Hard cap with ratchet headgear


Hoods, Accessories


Aluminized Zetex lightweight approach hood withheadgear

Aluminized Zetex approach hood with built-inhard cap

Aluminized Zetex approach hood with headgearand mesh window

FABRIC OPTIONS: Aluminized Zetex,

Aluminized Kevlar, Aluminized Nomex,

Aluminized PBI/Kevlar, & Aluminized Rayon


12/16

Aluminized Zetex safety clothing is made

with aluminum film bonded to durable

Zetex fabric. They provide excellent

insulation, flexibility, heat reflection, and

resistance to delamination, cracking, and

peeling. They are designed to be used in

applications where the ambient tempera-

ture does not exceed 200F (93C).

Standard lining used is FR cotton lining.

Other linings available are: wool, quilted

Nomex, and neoprene.

Use Zetex Safety Clothing in many applica-

tionsfoundries, steel mills, manufactur-

ing plants, chemical plants.

Aluminized Zetex is designed toreflect 90% of the radiant heat.

Aluminized Zetex full length coat Lightweight Aluminized PBI/Kevlar coat with

Raglan sleeve and 2" collar

Aluminized Zetex bib pants Aluminized Zetex waist pants

Coats and Pants

ALUMINIZED SAFETY CLOTHING

Aluminized Nomex coat with vent back


Coats and PantsCoat lengths are 32" to 50" (813mm to 1270mm). Standard featuresinclude front snaps, sleeve adjustments, and tailored sleeves.

Lining with NFPA approved vapor barrier available.

A wide range of sizes of pants (S, M, L, XL, 2XL, 3XL) are available.

Standard features include storm-fly front and suspenders.


13/16

Aprons, Sleeves, Boots and Leggings

ALUMINIZED SAFETY CLOTHING

Boots and LeggingsFive boot styles designed to fit over work shoes are available (see Protective Suits on page 8 and 9).

Leggings include hip, knee, and shin lengths. All leggings use a leather shoe cover

Aluminized Zetex shin leggingAluminized Zetex 150 Series boots Aluminized Zetex hip legging

Aluminized Zetex bib apronAluminized Zetex 18" sleeves and waist apron

FABRIC OPTIONS

Newtex offers a wide choice of aluminized fabrics to order: Aluminized Zetex, Aluminized Kevlar,Aluminized Nomex, Aluminized PBI/Kevlar, & Aluminized Rayon

Aprons and SleevesWaist, surgeon and bib stylesavailable. Wide range of sizesavailable for waist and surgeonstyles (specify chest size). Bibstyle aprons are 24" and 29"(610mm to 737mm) at waist and30" to 54" (762mm to 1372mm)in length.

Standard sleeve sizes are from12" to 24" (305mm to 610mm)

lengths. All sleeves have univer-sal Velcro adjustments.

For radiant heat

protection, use

Aluminized Zetex 600

fabric. For molten

metal splash protec-

tion, use Aluminized

Zetex 800 fabric


14/16

Z-Shield in gold with tucked edges. Also available in

other colors

HIGH TEMPERATURE SAFETY BLANKETS AND CURTAINS

Newtex makes a wide variety of fabrics for safety blanket andcurtain applications. Standard roll widths are 40 inch (1m),

60 inch (1.5m) and 72 inch (1.8m); roll length is 50 yards

ZetexPlus

UP TO 1100F (593C) UP TO 2000F (1093C)

Z-Sil 600 and Z-Sil 1100

Zetex and ZetexPlus fabric names have been long associated with quality products for high temperatureapplications, including welding. Newtex Industries offers an expanded line of fabrics for welding protection

and fabrication into safety blankets, curtains, and shields. These fabrics are designed to protect personnel andequipment from sparks and molten metal splash in shipbuilding, power generation, chemical processing and

refinery applications along with many other industrial uses.

We Make A Full Line Of Theater Curtains


15/16

SAFETY FIRST

Know What Type of Protection is Needed

Ambient Heat is the heat (or temperature) of the surrounding air.Example:the air temperature in a factory setting is 100F (38C)

Conductive Heat is heat transferred as a result of direct contact with a heat source.

Example:in the same factory setting, the temperature of a hot waterpipe is 160F (71C)

Radiant Heat is heat absorbed by objects struck by heat energy rays.Example:the radiant heat from the hot water pipe is 160F (71C) next

to the pipe; the radiant heat from the hot water pipe decreasesas one walks away from the hot water pipe

HIGH TEMPERATURE SAFETY BLANKETS AND CURTAINS

Coating And Custom Dye OptionsSilicone, Latex, Aluminized and ZetexPlus coatings.

We Custom Dye Fabrics

Call or visit our web site for technicalinformation and customer service.

Zetex and ZetexPlus fabrics have low smoke emissions

UP TO 1100F (593C) UP TO 2000F (1093C)

OpticalDensity(4min.)

Zetex 800

80

70

60

50

40

30

20

10

0 ZetexPlus 800 Aramid

Zetex and ZetexPlus fabrics have beentested for molten metal splash test

Welding demo with Zetex fabric

Zetex Emergency Fire Safety Blanket.Also available as private label


16/16

UP TO 2000F (1093C)UP TO 1100F (593C)

Newtex Industries is a leading integrated manufacturer of high-tech, heat resistant products for industrial and safety markets.Newtex products, under the Zetex and ZetexPlus brand names, include: heat resistant fabrics, welding fabrics, tapes, ropes, tubings,high temperature belting, and mat; fire entry, kiln, proximity, and approach suits; gloves, and mitts; aluminized safety clothing; and

theater curtains. Newtex distributes its products to more than 60 countries.

Headquarters: 8050 Victor-Mendon Road, Victor, NY 14564 USATel: 800/836-1001 Fax: 716/924-4645

E-mail: [email protected] Internet: www.newtex.com

Western U.S. Office and Distribution Center: 34016 Ninth Avenue South, Building D, Suite 3, Federal Way, WA 98003Tel: 888/NEWTEX 1 Fax: 253/838-5603

Asia/Pacific Office and Distribution Center:Newtex Asia Pacific PTE LTD

BLK 120 Richfield Industrial Centre 01-03Eunos Ave 7, Singapore 409574

Tel: 65-7481138 Fax: 65-7480848 E-mail: [email protected]

Newtex, Zetex, and ZetexPlus are registered trademarks of Newtex Industries, Inc.

Z-Sil and Z-Shield are trademarks of Newtex Industries, Inc.

UL UL ListedULListed

Zetex and ZetexPlus fabrics meet orexceed one or more of the followingspecifications:

s UL 214 and

NFPA Spec No 701s UL 723 Flame Spread is 0, Smoke

Density is 0, Fuel Contributed is 0

s US Coast Guard Spec No 164.009

s US Military Spec MIL-C-20079

s US Military Spec MIL-I-24244 and

NRC 1.36 Spec

s European BS EN407 standards

s UBC 43-1, NFPA 252, and

California State Fire Marshall

Newtex makes a complete line of high temperature products

for industrial applications. Call us for the Industrial

Products Catalog or visit our web site.

Documents

Master Safety New Tex