-
Manual for breakout board
1
Manual for Breakout Board
CATALOG
OVERALL WIRING DIAGRAM：
................................................... 2
INTERFACE AND ITS DEFINITION
............................................... 2
1、25-pin parallel port control is defined as follows：
....................................................................................2
2、Restriction interface
definition................................................................................................................3
3、Relay Interface
..........................................................................................................................................3
4、5 Road stepper motor driver
interface：....................................................................................................4
MACH SOFTWARE
USAGE..............................................................
4
3.1、MACH3 SOFTWARE
STARTUP：...................................................................................................................4
3.2、DRIVER INTERFACE BASIC SETTING FOR MACH3：
........................................................................................5
3.3、LIMIT SWITCH SETIING FOR MACH 3
：.........................................................................................................6
3.4、RUN WAY FOR G CODE：
..............................................................................................................................7
CNC4YOU.co.uk
-
Manual for breakout board
2
Overall wiring diagram：
Interface and its definition
The above diagram shows the order in accordance with
identified
CNC4YOU.co.uk
-
Manual for breakout board
3
1、25-pin parallel port control is defined as follow：
PIN1 PIN2 PIN3 PIN4 PIN5 PIN6 PIN7 PIN8 PIN9 PIN10 EN STEPA DIRA
STEPB DIRB STEPC DIRC STEPD DIRD DIN1 All axis enabled
A axis pulse
A axis direction
B axis pulse
B axis direction
C axis pulse
C axis direction
D axis pulse
D axis direction
Limit 1
PIN11 PIN12 PIN13 PIN14 PIN16 PIN17 PIN18~25 DIN2 DIN3 DIN4 RLY
STEPE DIRE GND Limit 2 Limit 3 Limit 4 Reply
control E axis pulse
E axis direction
GND
2、Restriction interface definition
Limit Interface with DB9 connector, the connection method as
shown below：
3、Relay Interface
CNC4YOU.co.uk
-
Manual for breakout board
4
Note: If you connect the A and the public side, after connected
directly between A and the public side is the conduction of;
if you are connected to B and the public side, the connection is
completed only between B and the public side pull drive
when is the turn of.
4、5 Road stepper motor driver interface：
Can connect a total of five stepper motor driver, the definition
of top-down followed by EN CW CK VCC GND, representing 5 Road,
enable signal, the direction of the signal, pulse signals, 5V,
ground, as shown below:
MACH Software Usage
3.1、MACH3 software startup：
MACH3 software installed, there are three icons on the desktop,
click on the icon opens the interface shown in
Figure 1 follows: Figure 1 mach3 main interface
CNC4YOU.co.uk
-
Manual for breakout board
5
3.2、Driver interface basic setting for mach3：
Figure 2, open the config menu, the menu under the PORT &
PINS
Figure 2
Figure 3
Set on the circle 1 where you can set a basic frequency, the
parameters affect the motor rotation speed. Set up a place
after
Figure
CNC4YOU.co.uk
-
Manual for breakout board
6
the selection circle 2, the configuration pin definitions,
Figure
4
figure4 According to the definition of the board parallel port,
follow the map on the circle to indicate the definition modify the
software to set relay and enable
pins. Figure 5，pin numer setting 14 、1。
3.3、limit switch setiing for mach 3：
Then Figure 5 interface, click on input signal, set the
parameters shown in Figure
CNC4YOU.co.uk
-
Manual for breakout board
7
6. Figure 6
3.4 Run way for g code：
Mach3 software used for testing with the G code, and Figure 7, G
code menu click Run
Figure 7
CNC4YOU.co.uk
-
Manual for breakout board
8
Find you want to run the Gcode, and open in Figure 8
8
Figure 8
Figure 9
CNC4YOU.co.uk
-
Manual for breakout board
9
Open the G code, you can see the red RESET flashing, you can use
the mouse clicking on the RESET so stop flashing, then you can
press circle 2 position CYCLESTART run. Also if you need manual
control, they can press the TAB key on the keyboard to open manual
control panel, manual control panel shown in Figure 10
Figure 10
CNC4YOU.co.uk
