Lokring Process Catalog

PROCESS PAMPHLET

LOKRING

960 GATEWAY DRIVE BURLINGTON ONTARIO CANADA L7L 5K7

TEL.: (905) 639-4050 FAX: (905) 639-6163 ___________________________________________________________________________________________________www.lokring.com

www.lokring.com Copyright 2003 Lokring Technology Corporation, All rights reserved 4.04 FS-3000 (10-17-03)

1

T E C H N O L O G Y C O R P O R A T I O N LOKRINGTM Specifications FS-3000 for Series MAS-3000 Carbon Steel Fittings

Scope of Specifications: Series MAS-3000 carbon steel pipe fittings manufactured by LOKRINGTM. Pressure temperature ratings of qualified fittings, and matched pipe sized (NPS) and schedules are detailed in Table 1 and 2 of this specification. Fitting configurations and dimensions are detailed in LOKRINGTM product catalogs. Installation tool envelope dimensions, and minimum fit-up dimensions are provided in LOKRINGTM Installation Procedure Lp-105. For installation procedures, and selection of installation tooling, see LP-105 Installation Procedure. Fittings are designed for carbon steel pipe to ASTM-A106B and ASTM-A53B. Fitting Material Specification: Fitting body and swaging rings are manufactured from hot rolled micro alloyed 15V24 carbon steel bar or Drawn Over Mandrel, stress relieved tubing. Bar stock material shall conform to ASTM A675 and the chemical and mechanical properties shall conform to LOKRINGTM material specification LMS 92-10. Tube stock material shall conform to ASTM A513 / DIN 2393 grade ST 52.3 and the chemical and mechanical properties shall conform to LOKRINGTM material specification LMS 97-20. LOKRING's Carbon Steel Repair Couplings are made of a stainless steel body with carbon steel drive rings, see LOKRING specification FS40 for material data. For shelf-life corrosion protection, machined fittings shall be subjected to a black-oxiding process, followed by a rust inhibiting dip. Contact LOKRINGTM for material or plating specifications.

Table 1: Pressure-Temperature Ratings (Note 1, 3, 5)

Fitting/Matching Pipe Assembly Ambient Maximum design pressures (psi) LOKRING Fitting (Note 2) Matching Pipe Schedule ASME B31.1 ASME B31.3 MAS-3000-XXX-P04 NPS 40 4890 6250 MAS-3000-XXX-P06 NPS 40 4040 5390 MAS-3000-XXX-P08 NPS 40 3890 5190 MAS-3000-XXX-P12 NPS 40 3230 4300 MAS-3000-XXX-P16 NPS 1 40 3030 4050 MAS-3000-XXX-P20 NPS 1 40 2480 3310 MAS-3000-XXX-P24 NPS 1 40 2200 2930 MAS-3000-XXX-P32 NPS 2 40 1790 2390 MAS-3000-XXX-P48 NPS 3 40 1700 2270 MAS-3000-XXX-P04 NPS 80 6610 8810 MAS-3000-XXX-P06 NPS 80 5600 7470 MAS-3000-XXX-P08 NPS 80 5250 7000 MAS-3000-XXX-P12 NPS 80 4400 5870 MAS-3000-XXX-P16 NPS 1 80 4080 5440 MAS-3000-XXX-P20 NPS 1 80 3350 4460 MAS-3000-XXX-P24 NPS 1 80 3970 3960 MAS-3000-XXX-P32 NPS 2 80 2420 3230 MAS-3000-XXX-P48 NPS 3 80 2260 2470 MAS-3000-XXX-P08 NPS 160 4810 6410 MAS-3000-XXX-P12 NPS 160 4240 5650 MAS-3000-XXX-P16 NPS 1 160 3650 4870 Notes: 1. Pressure-temperature ratings in Table 1 assume no corrosion allowance and negligible bending moments on the fitting. Please

consult the factory for more detailed design guidance. 2. Carbon Steel Repair Couplings have pressure ratings the same as those of LOKRING's stainless steel pipe fittings see

specification FS40 for details.

Table 2: Temperature Derating Factors (Note 1, 5)

Temperature Derating Factor (F) for ASME B31.3

400 1.00 500 0.945 600 0.865 650 0.751



www.lokring.com Copyright 2003 Lokring Technology Corporation, All rights reserved 4.04 FS-3000 (10-17-03)

2

T E C H N O L O G Y C O R P O R A T I O N Matching Pipe for Qualified Fittings: Carbon Steel to ASTM-A106B and ASTM-A53B (Note 3) Stress Intensification Factor I: 1.2. (Note 4, 5) Reference Qualification Document: Biersteker, Dietmann, Sareshwala, and Haupt, Qualification of Non-

Standard Product Form for ASME Code for pressing piping, B31 Applications Codes and Standards and Applications for Design and Analysis of Pressure Vessel and Piping Components, PVP-Vol. 210-1, American Society of Mechanical Engineers, New York, 1991.

Note 1: Piping systems containing the piping assemblies listed may establish design pressures up to and including the ambient maximum

design pressure given for temperature from -20 to 400 F for ASME B31.3 (based on allowable stresses for the matching pipe of 15,000 psi and 20,000 psi respectively). For temperatures above 400F in ASME B31.1 the maximum design pressure given shall be multiplied by the temperature derating factor listed in Table 2. Interpolation between derating factors is permitted. For methodology used to develop maximum design pressures in accordance with ASME codes, see Reference Qualification Document.

Testing performed has disclosed that the toughness for the l5V24 material at -20F to be comparable or better than matching pipe material (document available upon request). However, the toughness of matching pipe material may be affected when operating below normal ambient temperatures.

Note 2: XXX designates fitting configuration: CPL = Coupling; TEE = Straight Leg Tee; EL90 = 90 Elbow. See product catalogs for

available configurations. Note 3: Pipe used for pressure qualification tested was a seamless construction to ASME-SA106 Grade B, and electric resistance welded

(ERW) construction to ASME-SA53 Grade B. Maximum pipe hardness Rb 90. For assemblies using ASTM A106 Grade A, A53 Grade A, or A587 matching pipe, the listed pressure-temperature ratings shall be multiplied by 0.80. Prior to using Series MAS-3000 fittings on other carbon steel pipe specifications, schedules, or constructions, consult with LOKRINGTM.

When installing on ERW pipe, the longitudinal weld seam shall be drawn smooth or sanded to remove any suckback, flat spots, or other surface irregularities. If the required surface conditions cannot be met, the use of anaerobic sealant, such as Loctite PST sealant (given process compatibility) is recommended.

Note 4: The stress intensification factor, I, used for B31.1 thermal expansion and B31.3 displacement stress-range calculations has been

established in accordance with test procedures outlined in the Reference Qualification Document. In this testing, an assembly consisting of a LOKRINGTM coupling two equal length pipe tangents on either side of the coupling was fabricated using standard LOKRINGTM installation procedures. A uniform bending moment was applied to the fitting/pipe assembly. This moment induced a bending stress in the assembly greater than the pipe material yield strength (35,000 psi), and caused the assembly to flex in plane passing through the neutral axis. In one complete flexural cycle, the fitting/pipe assembly bends an equal distance to either side of the neutral axis. The stress intensification thus determined means that the LOKRINGTM fitting/matching pipe assembly will normally survive 7,000 fully reversed flexural cycles with the matching pipe nominal stress equal to the pipe material yield strength.

While extensive fatigue testing of the l5V24 fitting and matching pipe assemblies have been performed (documentation available upon request), it is cautioned that the l5V24 material is among the highest tensile strength materials approved for use in pressure component applications. In developing stress intensification data, one assembly endured 80,000 cycles at a nominal moment stress of 35,000 psi without failure. However, both B31.l and B31.3 provide notes suggesting caution when designing with materials other than those in the ASME data base. Thus, until more data is available, it is recommended that the B3l.l thermal expansion and B3l.3 displacement allowable stress-ranges be conservatively based upon grade B carbon steel allowable stress values.

Note 5: The pressure-temperature ratings and the stress intensification factor given are for the LOKRINGTM coupling fitting/matching

pipe joint only. If the LOKRINGTM fitting is the TEE or EL90, a forged tee or elbow exists between LOKRINGTM couplings located at the ends of the product form. Calculations and testing confirm that effective pressure-temperature ratings and the effective stress intensification factors (based on matching pipe cross-sectional properties) are enveloped by LOKRINGTM coupling/matching pipe values. This is true as well for conditions where corrosion has internally reduced the wall thickness such that pressure-temperature rating and stress intensification factor could be affected. For flexibility calculations, the tee or elbow may conservatively be considered as a rigid member.



www.lokring.com Copyright 2003 Lokring Technology Corporation, All rights reserved 4.05 FS40 (10-01-03)

1

T E C H N O L O G Y C O R P O R A T I O N

LOKRINGTM Specifications FS40 for Series SS40 316L Stainless Steel Fittings

Scope of Specification: Series SS40 Type 316L stainless steel pipe fittings manufactured by LOKRINGTM. Pressure-temperature ratings of qualified fittings, and matching pipe sizes (NPS) and schedules detailed in Tables 1 and 2 of this specification. Fitting configurations and dimensions are detailed in LOKRINGTM product catalogs. Installation tool envelope dimensions, and minimum fit-up dimensions are provided in LOKRINGTM Installation Procedure Lp-105. For installation procedures, and selection of installation tooling, see Installation Procedure LP-105. Fittings are designed for stainless steel pipe to ASTM-A312, and for other pipe materials of comparable strength and ductility (Note 2). Material of Construction: Fitting bodies and swage rings are manufactured for corrosion resistant steel type 316L (UNS designation S31603). Physical and mechanical properties of bar stock material conform to ASTM A276 or A479, and to LOKRINGTM material specifications LMS 90-03 or LMS 95-15. Physical and mechanical properties of tube stock material conform to ASTM A511, and to LOKRINGTM material specification LMS 92-11, LMS 96-18 or LMS 99-23. Fittings are fabricated using Schedule 40 butt weld fittings to ANSI B16.9 and ASTM A403 WP/W. LOKRINGTM flanges are fabricated using forged weld neck flanges to ANSI/ASME B 16.5 Sch 40 bore.

Table 1: Pressure-Temperature Ratings (Note 1)

Ambient Maximum design pressures (psi) LOKRING Fitting NPS Pipe Sch ASME B31.3 ASME B31.1

10S 4529 3781 40S 6300 5300 SS40-XXX-P04 80S 8000 6000

10S 4290 4030 40S 5060 4760 SS40-XXX-P08 80S 5060 4760

10S 3380 3170 40S 4470 4210 SS40-XXX-P12 80S 5250 4930

10S 3550 3340 40S 3920 3680 SS40-XXX-P16 1 80S 4240 3990

10S 2410 2260 40S 2600 2440 SS40-XXX-P24 1 80S 2600 2440

10S 1840 1730 SS40-XXX-P32 2 40S 1840 1730

10S 1150 920 40S 2100 1700 SS40-XXX-P48 3 80S 1705 1350

Note: Ambient maximum design pressures shown assume no corrosion allowance and negligible bending moments. Please consult the factory for more details. Qualified Matching Pipe: See Note 2 Stress Intensification Factor I: 1.2 (Note 4) Qualification Document: Biersteker, Dietemann, Sareshwala, and Haupt, Qualification of

Non-Standard Product Form of ASME Code for pressure piping, B31 Applications, Codes and Standards and Applications for Design and Analysis of Pressure Vessel and Piping Components, PVP-Vol. 210-1, American Society of Mechanical Engineers, New York, 1991.



www.lokring.com Copyright 2003 Lokring Technology Corporation, All rights reserved 4.05 FS40 (10-01-03)

2


Table 2: Temperature Derating Factors (Note 1)

Temperature Temperature derating factors In accordance with (F) ASME B31.1 ASME B31.3

200 1.00 1.00 300 0.98 1.00 400 0.96 0.97 500 0.96 0.90 600 0.90 0.85 650 0.89 0.84 700 0.87 0.82 750 0.86 0.81 800 0.85 0.80

Note 1: Piping systems containing the piping assembles listed may establish design pressures up to and including the ambient maximum

design pressure given for temperatures from -20 to 100 degrees F for ASME B31.1, and from -325 to 100 degrees F for ASME B31.3 (based on allowable stresses for the matching pipe of 18,000 psi and 20,000 psi respectively). For methodology used to develop maximum design pressures in accordance with ASME codes, see Reference Qualification Document, available on request. For temperature derating factor listed in Table 2. Interpolation between derating factors is permitted.

Note 2: Qualified matching pipe shall conform to seamless or electric resistance welded (ERW) constructions of ASTM-A312. All pipe

shall be furnished in the heat-treated condition as per ASTM A312/A312M. Pipe shall be of high quality, fully annealed construction with maximum Rockwell B scale hardness of 90. Fittings may also be installed on carbon steel pipe to ASTM A53 or A106 provided the dimensional and physical properties meet the requirements of qualified stainless steel pipe. The designer should evaluate the potential for galvanic corrosion between the carbon steel pipe and stainless steel fitting for the contemplated application, and should limit the maximum rated temperature of the carbon steel pipe. SS40 series fittings should not be installed on galvanized pipe used for flammable or process services.

Discontinuities as the longitudinal weld seam of ERW pipe can provide a leak path if not removed or sealed. Poor longitudinal welding can result in a visible depression (or suck back): poor longitudinal fittings on ERW pipe in which the weld bead has been drawn or sanded smooth, and is not visible to the naked eye. If the required surface conditions cannot be met, the use of anaerobic sealant, such as Loctite PST sealant (given process compatibility), is suggested.

Note 3: XXX designates fitting configuration: CPL = Coupling; TEE = Straight Leg Tee; EL90 = 90Elbow. See product catalogs for

available configurations. Note 4: The methodology used to establish the stress intensification factor, I, use of B31.1 thermal expansion and B31.3 displacement

stress-range calculations is outlined in the Reference Qualification Document, available on request. The stress intensification thus determined means that the LOKRINGTM fitting/matching assembly will normally survive 7,000 fully reversing flexural cycles with the matching pipe nominal stress equal to the pipe material yield strength.

960 GATEWAY DRIVE BURLINGTON ONTARIO CANADA L7L 5K7 TEL.: (905) 639-4050 FAX: (905) 639-6163

_______________________________________________________________________________________________ www.lokring.com

Registered Trademark of Lokring Technology Corporation Trademark of Lokring Technology Corporation

www.lokring.com Copyright 2003 Lokring Technology Corporation, All rights reserved 4.06 FS40-T (08-19-03)

1


Specification FS40-T for Lokring Type 316L Stainless Steel Tube Fittings

Scope: FS40-T covers Tube fittings manufactured by Lokring TM from 316L corrosion resistant steel. Pressure Temperature ratings of qualified couplings and matching tube sizes and wall thickness are detailed in table 1. Sizes and dimensions are detailed in Lokring product catalogs. Fittings were designed and tested to join stainless steel tubing to ASTM A269 or A213 or equivalent (note 2). Ratings are based on proper installation of fittings, for appropriate installation procedures and installation tooling, consult factory. Material Specification: Fitting bodies swage rings and shapes are manufactured from corrosion resistant steel, type 316L (UNS designation S31603). Physical and mechanical properties of bar stock material conform to ASTM A276 or A479 and to the appropriate Lokring material specification. Lokring elbows, tees, flanges and other shapes that cannot conveniently be manufactured from a single component are fabricated by butt welding one or more machined Lokring half bodies onto a butt weld fitting procured to ASME/ANSI B16.9 or Flange to ASME/ANSI B16.5 or to a specially designed component machined from the same material type as the half bodies. The weld end preparation on all components has been specifically designed to produce consistent high quality welds using automatic, semi-automatic and manual TIG welding machines.

All welding is performed in accordance with Welding Procedure Specifications and Welding Procedure Qualification Records that have been qualified to ASME Section IX. All personnel performing welds are certified to the local governing body in accordance to ASME Section IX.

Table 1 Pressure Rating

Coupling - Matching Tube Assembly Ambient Max. Design Press. (PSI) 1

Fitting Size Tube O. D. 2 Wall Thickness 3 B31.3 4

T04 1/4 0.065" 9050 T06 3/8 0.065" 5650 T08 1/2 0.065" 4270 T10 5/8 0.065" 3750 T12 3/4 0.065" 3510 T14 7/8 0.065" 3420 T16 1 0.083" 3380 T20 1 1/4 0.109" 3550 T24 1 1/2 0.120" 3410 T32 2 0.083" 1690

Qualified Matching Tube: Stainless Steel tube to ASTM A269 or A213 2

Flexural Fatigue Testing: See note 5

960 GATEWAY DRIVE BURLINGTON ONTARIO CANADA L7L 5K7 TEL.: (905) 639-4050 FAX: (905) 639-6163

_______________________________________________________________________________________________ www.lokring.com

Registered Trademark of Lokring Technology Corporation Trademark of Lokring Technology Corporation

www.lokring.com Copyright 2003 Lokring Technology Corporation, All rights reserved 4.06 FS40-T (08-19-03)

2


Reference Document: Biersteker, Dietemann, Sareshwala and Haupt, Qualification of Non-Standard

product Form for ASME Code for Pressure Piping, B31 Applications Codes and Standards and Applications for Design and Analysis of Pressure Vessel and Piping Components, PVP-Vol 210-1, American Society of Mechanical Engineers, New York, 1991

Table 2 Temperature De-rating Factors

Temperature Degree F.

Temperature de-rating factors in accordance with

ASME B31.3 200 1.00 300 1.00 400 0.97 500 0.90 600 0.85 650 0.84 700 0.82 750 0.81 800 0.80

Notes:

1. For temperatures above 100 Deg. F., the maximum design pressure given shall be multiplied by the temperature De-rating factor listed in table 2. Interpolating between de-rating factors is permitted.

2. Qualified matching tube shall be Types 316/316L or 304/304L, and conform to seamless or electric resistance welded (ERW) construction of ASTM A269 and/or A 213. Discontinuities at the longitudinal weld seam of ERW tube can provide a leak path if not removed. Poor welding can result in a visible depression (or suck-back), poor weld bead removal can result in a raised portion or a flat spot at the weld. Only install Lokring fittings on ERW tube in which the weld bead has been drawn or sanded smooth and is not visible to the naked eye. If the required surface conditions cannot be met, the use of an anaerobic sealant such as Loctite PST (given process compatibility) will usually ensure a sound connection.

3. Pressure rating is maximum rating for the fitting size shown. Heavier wall tubing may be used, but pressure rating will remain at specified value. Conversely thinner wall tube may be used (minimum 0.035 up to O.D., 0.065 for sizes above ) and pressure rating will be dependant on tube pressure limitations.

4. Tubing systems containing the tubing systems listed may establish design pressures up to and including the ambient maximum design pressure given for temperatures from 325 to 100 Deg. F for ASME B31.3 (based on the use of seamless tube with allowable stresses of 20,000 PSI). Ambient temperature system design pressure ratings must be de-rated when using ERW (welded) and/or L grade tubing with lower allowable stress.

5. In fatigue testing, assemblies consisting of a Lokring coupling and two equal length tube tangents on either side of the coupling were fabricated using standard Lokring installation procedures. A uniform bending moment was applied to the assembly, inducing a bending stress in the assembly equal to or greater than the tube minimum yield strength (38,000 PSI). One complete bending cycle consists of bending the assembly to one side of the neutral axis to the specified value and then back again through the neutral axis to the specified value on the opposite side and then back to the neutral axis. All assemblies exceeded 30,000 complete bending cycles without leakage, and many greatly exceeded this value. Consult factory for other details.

Page 2

General Information

Couplings, Reducers, Adapters

Flanges

45 Elbows, 90 Elbows

90 Elbows, Tees

Page 4

Page 8

Page 10

Adapters, Reducer Bushings, Uthreads

Repair Couplings, Caps, SAE Fittings Page 6

Page 5

MAS-3000 PIPE FITTINGS


www.lokring.com Copyright 2003 Lokring Technology Corporation, All Rights Reserved. 6.01 MAS-3000 Carbon Steel Pipe Fittings (01-26-04)

Fitting Size (PXX)

Qualified Pipe Schedules

Insertion Depth Pre-Install, A

Insertion Depth Post-

Install, B

Outside Diameter, C

Inside Diameter, D

Minimum Straight Run

Before a Bend, E

1/4" (P04) 40/80/160 1.24 0.85 1.05 0.56 1.89

3/8" (P06) 40/80/160 1.37 0.95 1.24 0.69 2.08

1/2" (P08) 40/80/160 1.43 1.01 1.46 0.87 2.24

3/4" (P12) 40/80/160 1.62 1.16 1.60 1.08 2.52

1" (P16) 40/80/160 1.98 1.41 1.95 1.33 2.86

1 1/4" (P20) 40/80 2.21 1.57 2.29 1.68 3.33

1 1/2" (P24) 40/80 2.39 1.72 2.59 1.93 3.64

2" (P32) 40/80 2.92 2.16 3.26 2.41 3.95

3" (P48) 40/80 4.26 2.99 4.34 3.53 6.12

PRE-INSTALLED POSITION POST-INSTALLED POSITION

General Information

1. All dimensions in inches

2. Dimensions A, B, C, D & E are applicable to other fittings of the same size within this catalog

3. For use on carbon steel pipe as per ASTM A53 AND A106

4. For tooling dimensions refer to appropriate catalog

5. Fitting material Micro Alloyed Carbon Steel to LMS 92-10 or LMS 97-20

6. Standard coating is black oxide per LMS 93-12. Zinc plate is available as an alternate

7. CAD files in Autocad-DWG, Autocad-DXF and Intergraph PDS are available for most configurations, contact Lokring for details

8. Other part configurations than those shown and custom configurations may be available, contact Lokring for details

9. All dimensions are reference only and subject to change


www.lokring.com Copyright 2003 Lokring Technology Corporation, All Rights Reserved. 6.01 MAS-3000 Carbon Steel Pipe Fittings (01-26-04), Page 1 of 11

Fitting Size PXX

Piece Number

Take - Out, A

P04 9041374 0.40

P06 9041375 0.45

P08 9040071 0.47

P12 9040070 0.47

P16 9040069 0.60

P20 9040110 0.59

P24 9040068 0.66

P32 9040067 0.71

P48 9041804 0.85

(METRIC PIPE COUPLING)

Fitting Size MXX

Piece Number

Take - Out, A

M12 9062378 0.27

Fitting Size PXX-PYY

Piece Number

Take - Out, A

P08-P04 9062518 1.09

P08-P06 9062519 1.12

P12-P08 9060517 1.25

P16-P08 9060496 1.50

P16-P12 9060498 1.50

P20-P12 9061454 1.41

P20-P16 9061291 1.73

P24-P08 9060519 2.12

P24-P12 9060521 2.00

P24-P16 9060500 1.88

P32-P08 9060527 2.50

P32-P12 9060523 2.25

P32-P16 9060502 2.25

P32-P20 9062291 2.23

P32-P24 9060504 2.01

P48-P08 9061832 5.20

P48-P16 9061831 5.42

P48-P24 9061830 5.37

P48-P32 9061774 5.39

Fitting Size PXX-YY FPT

Piece Number

Take - Out, A

Thread

P08 - 0.50 9062270 0.98 1/2 - 14

P12 - 0.75 9062019 1.97 3/4 - 14

P16 - 1.00 9062020 2.38 1 - 11.5

P20 - 1.25 9061821 1.75 1 1/4 - 11.5

P24 - 1.50 9061822 1.81 1 1/2 - 11.5

P32 - 2 .00 9061823 1.89 2 - 11.5

Couplings, Reducers, Adapters

*Threaded end conforms to female NPT thread

MAS-3000-ADPT-PXX-YY FPT

MAS-3000-CPL-PXX

MAS-3000-RED-PXX-PYY

MAS-3000-CPL-MXX




Piece Number

Take - Out, A

Thread

P12-1/4" 9061734 0.60 1/4-18

Fitting Size PXX-XX MPT

Piece Number

Take - Out, A

Thread Across Flats

P04 - 1/4" 9062295 1.47 1/4 - 18 0.88

P08 - 1/2" 9060578 1.69 1/2 - 14 1.13

P12 - 3/4" 9060580 1.83 3/4 - 14 1.38

P16 - 1" 9060582 2.36 1 - 11.5 1.63

P20 - 1 1/4" 9062021 2.70 1 1/4 - 11.5 1.69

P24 - 1 1/2" 9060584 2.45 1 1/2 - 11.5 2.13

P32 - 2" 9060586 2.51 2 - 11.5 2.50

P48 - 3" 9061630 3.29 3 - 8 3.50

Fitting Size PXX-XX SAE

Piece Number

Take - Out, A

Thread

P08 - 0.5 9061812 1.00 3/4 -16 UNF

P12 - 0.75 9061813 1.38 1 1/16-12 UN

P16 - 1.0 9061814 1.50 1 5/16-12 UN

P20 - 1.25 9061815 1.50 1 5/8-12 UN

P24 - 1.5 9061816 1.63 1 7/8-12 UN

P32 - 2.0 9061817 3.00 2 1/2-12 UN

Fitting Size PXX-XX (M)

Piece Number

Take - Out, A

Thread

P08 - 0.5 9062154 1.44 3/4 -16 UNF

P12 - 0.75 9061884 1.92 1 1/16-12 UN

P16 - 1.0 9062022 2.68 1 5/16-12 UN

Fitting Size PXX-37FYY

Piece Number

Take - Out, A

Thread

P08-37F08 9062326 1.84 3/4-16 UNF-2A

P12-37F12 9062327 2.33 1 1/16-12 UN-2A

P16-37F16 9062328 2.63 1 5/16-12 UN-2A

P20-37F20 9062152 2.72 1 5/8-12 UN-2A

P24-37F24 9062329 3.32 1 7/8-12 UN-2A

P32-37F32 9062330 3.58 2 1/2-12 UN-2A

(O-ring straight thread adapter)

MAS-3000-ADPT-PXX-37FYY

* Threaded end conforms to SAE J514 (37 FLARE)

MAS-3000-ADPT-PXX-YY FPT

Adapters

(O-ring straight thread adapter)

MAS-3000-ADPT-PXX-XX SAE (M)


* Threaded end conforms to SAE J1926/2

MAS-3000-ADPT-PXX-XX MPT

*Threaded end conforms to male NPT thread

MAS-3000-ADPT-PXX-XX SAE

* Threaded end conforms to SAE J1926/1




Piece Number

Take - Out, A

Thread

P12-37F08 9062331 1.85 3/4-16 UNF-2A

P16-37F08 9062333 1.97 3/4-16 UNF-2A

P16-37F12 9062332 2.46 1 1/16-12 UN-2A

P20-37F16 9062334 2.69 1 5/16-12 UN-2A

P24-37F20 9062335 2.72 1 5/8-12 UN-2A

P32-37F24 9062336 3.33 1 7/8-12 UN-2A

Fitting Size PXX-XX NPS

Piece Number

Take - Out, A

Take - Out, B

P06 - 3/8" 9061924 1.34 1.00

P08 - 1/2" 9061787 1.40 1.00

P12 - 3/4" 9061788 1.46 1.00

P16 - 1" 9061789 1.52 1.00

P20 - 1 1/4" 9061925 1.59 1.00

P24 - 1 1/2 " 9061926 1.65 1.00

P32 - 2 " 9062521 1.70 1.00

Fitting Size PXX-YY NPS

Piece Number

Take - Out, A

P16-1/2" 9061612 2.68

Fitting Size PXX

Piece Number

Take - Out, A

Thread Across Flats

P08 9062267 1.80 1.482-14 UNS-2A 1.13

P32 9062268 3.55 3.508-10 UNS-2A 3.00

MAS-3000-RADPT-PXX-37FYY


Adapters, Reducer Bushings, Uthreads

*Thread and seal face per MIL-F-1183

MAS-3000-UTHREAD (400 WOG) PXX

MAS-3000-ADPT-PXX-XX NPS

* Non LOKRING end made to match up with

6000 lb socket weld adapter

MAS-3000-REDB-PXX-YY



Fitting Size PXX

Piece Number

Take - Out, A

P08 9060417 2.53

P12 9060423 2.72

P16 9060429 2.96

P20 9061287 3.00

P24 9060435 3.26

P32 9060441 3.34

P48 9061370 3.80

Fitting Size PXX

Piece Number

Take - Out, A

P08 9060419 2.71

P12 9060425 2.91

P16 9060431 3.21

P20 9061288 3.31

P24 9060437 3.51

P32 9060443 3.59

P48 9061371 4.17

Fitting Size PXX

Piece Number

Take - Out, A

P08 9061330 2.96

P12 9061331 3.16

P16 9061332 3.46

P20 consult Lokring

P24 9061333 3.82

P32 9061334 4.01

P48 9061372 4.55

Fitting Size Pxx

Piece Number

Take - Out, A

P08 9061325 3.27

P12 9061326 3.64

P16 9061327 3.91

P20 consult Lokring

P24 9061328 4.33

P32 9061329 5.11

P48 9061373 5.92

MAS-3000-FLNG1500-PXX

Flanges






Fitting Size Pxx

Piece Number

Take - Out, A

P06 9041801 N/A

P08 9041802 N/A

P12 9041803 N/A

P16 9060462 N/A

P20 9061290 N/A

P24 9060461 N/A

P32 9060460 N/A

P48 9041869 N/A

MAS-3000-CAP-PXX

Fitting Size PXX

Piece Number

Take - Out, A

P08 9060565 0.53

P12 9060567 0.55

P16 9060569 0.73

P20 9061289 2.25

P24 9060571 0.82

P32 9060573 2.34

P48 9061616 3.05

Fitting Size PXX

Piece Number

Take - Out, A

P08 9041859 2.28

P12 9041860 2.04

P16 9041861 2.25

P20 9041862 2.41

P24 9041863 2.54

P32 9041864 2.48

P48 9041865 2.93

Fitting Size PXX

Piece Number

Take - Out, A

P08 9041825 2.28

P12 9041826 2.04

P16 9041827 2.25

P20 9041828 2.41

P24 9041829 2.54

P32 9041830 2.48

P48 9041831 2.93

Split flange and hardware NOT included

MAS-3000-SAE61-PXX

*Non LOKRING end conforms to SAE J518 code 61

Split flange, O-ring per SAE J120 and hardware included

Repair Couplings, Caps, SAE61KIT, SAE61

MAS-3000-RCPL-PXX

*LOKRING's Carbon Steel Repair Couplings are slip over couplings made without an internal stop in order to facilitate repair work. They consist of a stainless steel body with carbon steel drive rings, their pressure ratings are the same as those of LOKRING's stainless steel SS40 pipe fittings.


MAS-3000-SAE61KIT-PXX



Fitting Size PXX

Piece Number

Take - Out, A

P08 9041852 1.72

P12 9041853 1.72

P16 9041854 2.14

P20 9041855 2.19

P24 9041856 2.68

P32 9041857 2.84

P48 9041858 3.37

Fitting Size PXX

Piece Number

Take - Out, A

P12 9041880 2.12

P16 9041881 2.31

P20 9041882 2.50

P24 9041883 2.72

P32 9041884 3.47

Fitting Size PXX

Piece Number

Take - Out, A

P12 9041875 2.12

P16 9041876 2.31

P20 9041877 2.50

P24 9041878 2.72

P32 9041879 3.47

Fitting Size PXX

Piece Number

Take - Out, A

P12 9041870 2.08

P16 9041871 2.38

P20 9041872 2.47

P24 9041873 2.98

P32 9041874 3.32

MAS-3000-SAE62-PXX

solid (tapped holes)


Split flange and hardware NOT included

MAS-3000-SAE62SLD-PXX


Split flange, O-ring per SAE J120 and hardware included

MAS-3000-SAE62KIT-PXX

solid (tapped holes)

SAE61SLD, SAE62KIT, SAE62, SAE62SLD

MAS-3000-SAE61SLD-PXX





Fitting Size PXX

Piece Number

Take - Out, A

P08 9060415 1.28

P12 9060421 1.41*

P16 9060427 1.61

P20 9061284 1.75

P24 9060433 1.94

P32 9060439 2.21

P48 9061368 3.20


Piece Number

Take - Out, A

Take - Out, B

Thread

P20-1 1/4 9062316 1.75 2.77 1-1/4 - 11.5

Fitting Size PXX

Piece Number

Take - Out, A

Take - Out, B

ThreadAcross Flats

P20 9062150 1.75 2.97 1 5/8-12 1.69

Fitting Size PXX

Piece Number

Take - Out, A

P08 9061396 1.62

P12 9061203 1.54

45 Elbows, 45 Reducing Elbow Adapters, 90 Elbows

MAS-3000-EL90-PXX

MAS-3000-EL45-PXX

MAS-3000-REL45-PXX-37FXX


MAS-3000-EL45-PXX-YY FPT


* Dimension of 1.72 may be furnished at manufacturer's option



Fitting Size PXX

Piece Number

Take - Out, A

P08 9061946 2.15

P12 9061947 1.79*

P16 9061145 2.27

P20 9061285 2.63

P24 9061192 3.07

P32 9060974 3.84

P48 9061369 5.55


Piece Number

Take - Out, A

Take - Out,, B

Thread NPT

P12-1/4 9061735 1.34 0.75 1/4-18

Fitting Size Pxx

Piece Number

Take - Out, A

Take - Out, B

ThreadAcross Flats

P20 9062151 2.63 3.85 1 5/8-12 1.69

Fitting Size PXX

Piece Number

Take - Out, A

Take - Out, B

C*

P24 9062322 3.06 7.66 2.61

P48 9062386 5.55 13.50 4.00

90 Elbows, 90 Elbow Adapters, Street Elbows

MAS-3000-SEL90-PXX

C* Maximum cut on pipe end

MAS-3000-REL90-PXX-37FXX


* Dimension of 1.42 may be furnished at manufacturer's option


MAS-3000-EL90LR-PXX

MAS-3000-EL90-PXX-YY FPT



Fitting Size PXX

Piece Number

Take - Out, A

Take - Out, B

P24 9062389 3.05 1.31

P32 9062520 3.28 1.66

Fitting Size PXX

Piece Number

Take - Out, A

Take - Out, B

P24 9062392 3.28 1.66

Fitting Size PXX

Piece Number

Take - Out, A

P08 9061948 1.65

P12 9061949 1.78

P16 9061144 2.27

P20 9061286 2.63

P24 9061191 3.07

P32 9060602 3.34

P48 9061367 4.43

Fitting Size PXX

Piece Number

Take - Out, A

P08 9061397 1.62

P12 9061401 1.54

MAS-3000-TEESR-PXX

90 SAE 61 Eblows, Tees, Reducing Tees

MAS-3000-TEE-PXX

MAS-3000-SAE61EL90-PXX

MAS-3000-SAE62EL90-PXX

*Non Lokring end conforms to SAE J518 code 62 c/w O-ring groove and thru holes

*Non Lokring end conforms to SAE J518 code 61 c/w O-ring groove and thru holes




Piece Number

Take - Out, A

Take - Out, B

P12-P08 9061398 1.54 2.01

P16-P08 9061344 2.27 2.15

P16-P12 9061343 2.27 2.16

P20-P12 9061632 2.63 3.04

P20-P16 9061292 2.63 2.72

P24-P08 9061399 3.07 2.90

P24-P12 9061402 3.07 2.91

P24-P16 9061403 3.07 3.02

P32-P08 9060975 3.34 2.65

P32-P12 9060605 3.34 2.66

P32-P16 9060604 3.34 2.77

P32-P24 9060603 3.34 3.20

P48-P12 9061618 4.35 3.39

P48-P16 9061617 4.35 3.50

P48-P24 9061615 4.35 3.75

P48-P32 9061408 4.35 3.78

(LONG RADIUS REDUCING TEE)


Piece Number

Take - Out, A

Take - Out, B

P12-P08 9061951 1.78 2.26

Fitting Size PXX-YY SAE

Piece Number

Take - Out, A

Take - Out, B

Thread

P20-1.25 SAE 9062153 2.63 3.37 1-5/8 - 12 UN-2B

Fitting Size PXX-YY

Piece Number

Take - Out, A

Take - Out, B

P48-1-1/2" 9062206 4.43 5.32

*Drop conforms to ASME/ANSI B16.5 150 lb flange

MAS-3000-RTEE (FLNG)-PXX-PYY

MAS-3000-RTEE-PXX-PYY

Reducing Tees, Tee Adapters

MAS-3000-REDTLR-PXX-PYY

*Drop conforms to SAE J1926/1

MAS-3000-RTEE-PXX-YY SAE


XX XX

YY

XX XX

YY


Flanges, Clean in Place, Caps

SAE Fittings, 45 Elbows, 90 Elbows

90 Elbows, 90 Elbow Adapters, Tees

Page 5Adapters, Reducer Bushings, Uthreads, Utails

Uthreads, Unions, Flanges Page 6

Page 8

Page 9

Page 7

General Information

Couplings, Reducers

Reducers, Adapters

Page 1

Page 2

Page 3

Drop Tees, Obtuse Tees, Tee Adapters, Cross

Page 13

Reducing Tees, Double Reducing Tees, Drop Tees

Page 10

SS40STAINLESS STEEL PIPE FITTINGS


www.lokring.com Copyright 2003 Lokring Technology Corporation, All Rights Reserved. 6.02 SS40 Stainless Steel Pipe Fittings (02-23-04)

Fitting Size (PXX)

Qualified Wall Thickness



Install, B

Outside Diameter, C

Inside Diameter, D


Before a Bend, E

1/4" (P04) 10/ 40/ 80 1.45 1.05 1.06 0.56 1.89

3/8" (P06) 10/ 40/ 80 1.60 1.18 1.28 0.69 2.08

1/2" (P08) 10/ 40/ 80 1.72 1.29 1.49 0.86 2.24

3/4" (P12) 10/ 40/ 80 1.94 1.44 1.61 1.07 2.52

1" (P16) 10/ 40/ 80 2.20 1.66 1.96 1.33 2.86

1 1/4" (P20) 10/ 40/ 80 2.56 1.90 2.37 1.68 3.33

1 1/2" (P24) 10/ 40/ 80 2.80 2.05 2.63 1.92 3.64

2" (P32) 10/ 40 3.04 2.39 3.11 2.41 3.95

3" (P48) 10/ 40/ 80 4.71 3.41 4.50 3.53 6.12


General Information

1. All dimensions are in inches.

2. Dimensions A, B, C, D & E are applicable to all fittings of the same size within this catalog.

3. For use on 316, 316L stainless steel pipe as per ASTM A312 and carbon steel pipe as per ASTM A53 or A106. See table for qualified wall thickness.

4. For tooling dimensions refer to appropriate catalog.

5. Coupling "thru-bore" design permits tube to pass completely through. All other fittings (tees, elbows etc.) have an internal travel stop.

6. Fitting material 316L Stainless Steel as per ASTM A276 or ASTM 479.

7. CAD files in Autocad-DWG, Autocad-DXF and Intergraph PDS are available for most configurations, contact Lokring for details




www.lokring.com Copyright 2003 Lokring Technology Corporation, All Rights Reserved. 6.02 SS40 Stainless Steel Pipe Fittings (02-23-04), Page 1 of 13

Fitting Size PXX

Piece Number

Take - Out

P04 9062176 n/a

P06 9062177 n/a

P08 9040043 n/a

P12 9040106 n/a

P16 9040107 n/a

P20 9041293 n/a

P24 9040103 n/a

P32 9040108 n/a

P48 9041868 n/a

P48** 9041832 n/a

(METRIC PIPE COUPLING)

Fitting Size MXX

Piece Number

Take - Out

M12 9062377 n/a

M14 9041850 n/a

M15 9062199 n/a


Piece Number

Take - Out, A

P08-P06 9061610 0.67

P12-P08 9061270 0.83

P16-P08 9061271 1.02

P16-P12 9061272 0.90

P20-P16 9061301 1.04

P24-P12 9061345 1.85

P24-P16 9061273 1.70

P24-P20 9061848 0.88

P32-P16 9061274 2.07

P32-P20 9062273 1.77

P32-P24 9061275 1.24

P48-P16 9061880 4.50

P48-P32 9061878 4.61

(METRIC CONCENTRIC REDUCER)

Fitting Size MXX-MYY

Piece Number

Take - Out, A

M15-M14 9062200 0.52

SS40-RED-MXX-MYY

Couplings, Reducers

SS40-CPL-PXX

SS40-RED-PXX-PYY

**Coupling with zinc plated carbon steel drive rings is available at lower cost

SS40-CPL-MXX



(PIPE TO TUBE REDUCER)


Piece Number

Take - Out, A

P12-T12 9062256 0.66

P16-T08 9041866 0.64

P20-T20 9062149 0.84

P20-T24 9061347 0.84

P32-T32 9062102 1.19

(METRIC TO PIPE REDUCER)

Fitting Size MXX-PYY

Piece Number

Take - Out, A

M14-P04 9062264 0.40

M14-P08 9041851 0.58

Fitting Size PXX-XX FPT

Piece Number

Take - Out, C

Across Flats

Thread NPT

P04 - 1/4 consult Lokring 0.60 0.69 1/4-18

P06 - 3/8 9061762 0.90 0.94 3/8 - 18

P08 - 1/2 9061763 0.78 1.13 1/2 - 14

P12 - 3/4 9061764 0.80 1.31 3/4 - 14

P16 - 1 9061765 0.91 1.50 1 - 11.5

P20 - 1 1/4 9061766 0.93 1.88 1 1/4 -11.5

P24 - 1 1/2 9061767 0.93 2.06 1 1/2-11.5

Fitting Size PXX-XX MPT

Piece Number

Take - Out, A

Across Flats

Thread NPT

P04-1/4 9061744 1.45 0.63 1/4 - 18

P06-3/8 9061745 1.58 0.75 3/8-18

P08-1/2 9061261 1.46 0.94 1/2-14

P12-3/4 9061260 1.95 1.12 3/4-14

P16-1 9061259 2.26 1.37 1 - 11.5

P20-1 1/4 9061746 2.37 1.75 1 1/4 -11.5

P24-1 1/2 9061258 2.53 2.00 1 1/2 -11.5

P32-2 9061257 2.62 2.38 2 - 11.5

Reducers, Adapters

SS40-RED-MXX-PYY

SS40-ADPT-PXX-XX MPT

SS40-ADPT-PXX-XX FPT

SS40 & SS-3000-RED-PXX-TYY



Fitting Size PXX-YYMPT

Piece Number

Take - Out, A

Across Flats

Thread NPT

P04-1/2 9062376 1.45 0.88 1/2 - 14

P12-1/2 9062101 1.82 0.87 1/2 - 14

P16 - 3/4 9061768 1.95 1.12 3/4 - 14

P20 - 1 9061770 2.24 1.37 1 -11.5

P24 - 1 1/4 9061769 2.71 1.75 1 1/4-11.5

Fitting Size PXX-XX SAE

Piece Number

Take - Out, A

Across Flats

Thread UN

P08-0.5 9061940 0.82 1.06 3/4-16

P12-0.75 9061931 1.18 1.44 1 1/16-12

P16-1.00 9061932 1.20 1.63 1 5/16-12

P20-1.25 9061941 1.17 2.00 1 5/8-12

P24-1.5 9061942 1.37 2.25 1 7/8-12

P32-2.0 9061943 2.64 3.00 2 1/2-12


Piece Number

Take - Out, A

Across Flats

Thread UN

P08-37F08 9062397 1.36 1.13 3/4-16

P12-37F12 9062271 1.60 1.13 1 1/16-12


Piece Number

Take - Out, A

Across Flats

Thread UN

P12-37F08 9062396 1.39 1.13 3/4-16

P16-37F12 9061771 1.73 1.13 1 1/16-12

P20-37F16 9061772 1.63 1.38 1 5/16-12

P24-37F20 9601773 1.72 1.69 1 5/8-12

Fitting Size PXX-XX NPS

Piece Number

Take - Out, A

Take - Out, B

P06 - 3/8 9061921 1.00 1.34

P08 - 1/2 9061785 1.00 1.40

P12 - 3/4 9061783 1.00 1.46

P16 - 1 9061786 1.00 1.52

P20 - 1 1/4 9061922 1.00 1.59

P24 - 1 1/2 9061923 1.00 1.65

P32 - 2 9061944 1.02 1.67

(O-ring straight threaded adapter)

Adapters

SS40-ADPT-PXX-XX SAE

*Threaded end conforms to SAE J1926/1

SS40-RADPT-PXX-YY MPT

*Threaded end conforms to male NPT thread


* Non LOKRING end made to match up with

6000 lb socket weld adapter

SS40-ADPT-PXX-37FYY

SS40-ADPT-PXX-XX NPS

*Threaded end conforms to SAE J514 (37 Flare)

SS40-RADPT-PXX-37FYY



Fitting Size XX-YY

Piece Number

Take - Out, A

Across FlatsThread

NPT

1/2 x 1/2 9061264 3.77 0.87 1/2 - 14

3/4 x 3/4 9061265 4.10 1.12 3/4 -14

1 x 1 9061266 4.93 1.37 1 - 11.5

1 1/4 x 1 1/4 9061267 5.45 1.75 1 1/4-11.5

1 1/2 x 1 1/2 9061268 5.89 2.00 1 1/2-11.5

2 x 2 9061269 6.02 2.38 2 - 11.5

Fitting Size PXX-YY NPS

Piece Number

Take - Out, A

P06-1/2 9062173 2.54

P08-3/4 9061235 2.98

P08-1 9061236 3.67

P12-1 9061237 3.56

P16-1 1/4 9061238 4.12

P16-1 1/2 9061239 5.07

P16 - 2 9061241 5.46

P20-1 1/2 9061335 4.22

P24-2 9061240 6.41

Fitting Size PXX

Piece Number

Take - Out, A

Thread Across Flats

P04 9061580 1.58 1-3/16-12UN 15/16

P06 9061582 1.64 1-3/8-12UN 1-1/6

P08 9061584 1.66 1-3/4-12UN 1-1/4

P12 9061585 1.69 2 -12UN 1-5/8

P16 9061587 1.94 2-5/16-12NS 2

P20 9061589 2.11 2-3/4-12UN 2-3/8

P24 9061591 2.43 3-1/16-12NS 2-5/8

P32 9061593 2.61 3-3/4-12UN 3-3/16

Fitting Size PXX

Piece Number

Take - Out, A

Thread Across Flats

P04 9061581 1.24 1-3/16-12UN 1-3/8

P06 9061583 1.30 1-3/8-12UN 1-5/8

P08 9061613 1.25 1-3/4-12UN 2

P12 9061586 1.28 2 -12UN 2-1/4

P16 9061588 1.28 2-5/16-12NS 2-9/16

P20 9061590 1.33 2-3/4-12UN 3

P24 9061592 1.40 3-1/16-12NS 3-1/2

P32 9061594 1.46 3-3/4-12UN 4-1/8

*Thread and seal face conform to Navy dwg 803-1385884

Adapters, Reducer Bushings, Uthreads, Utails

SS40-ADPT-XX NPS-YY MPT

SS40-UTAIL-PXX

*Complete with BUNA-N O-Ring

SS40-REDB-PXX-YY NPS

SS40-UTHRD-PXX




Fitting Size PXX-YY

Piece Number

Take - Out, A

P12-1.00 9061596 1.20

Fitting Size PXX

Piece Number

Take - Out, A

Thread

P04 9061456 2.82 1-3/16-12UN

P06 9061457 2.94 1-3/8-12UN

P08 9061458 2.91 1-3/4-12UN

P12 9061459 2.97 2 -12UN

P16 9061460 3.22 2-5/16-12NS

P20 9061461 3.44 2-3/4-12UN

P24 9061462 3.83 3-1/16-12NS

P32 9061463 4.07 3-3/4-12UN

Fitting Size PXX

Piece Number

Take - Out, A

P08 9060052 2.23

P12 9061214 2.44

P16 9061219 2.57

P20 9061297 2.67

P24 9061215 2.87

P32 9061224 2.98

P48 9061679 3.68

P48** 9061726 3.68

Fitting Size PXX-XX

Piece Number

Take - Out, A

P32-1-1/2 9061559 3.59

Fitting Size PXX

Piece Number

Take - Out, A

P08 9060264 2.41

P12 9061231 2.63

P16 9061232 2.82

P20 9061298 2.98

P24 9061233 3.12

P32 9061234 3.23

P48 9061680 3.75

P48** 9061727 3.75

**Flange with zinc plated carbon steel drive ring is available at lower cost

* Flange conforms to ASME/ANSI B16.5, 300 LB

SS40-FLNG150-P32-1 1/2"




Uthreads, Unions, Flanges

SS40-FLNG300-PXX

*Complete with BUNA-N O-Ring

SS40-UNION-PXX


SS40-FLNG150-PXX

SS40-RUTAIL-PXX-YY



Fitting Size PXX

Piece Number

Take - Out, A

P08 9061320 2.41

P12 9061321 2.63

P16 9061322 2.82

P20 9061323 3.04

P24 9061324 3.18

P32 9061342 3.36

P48 9061681 3.88

P48** 9061728 3.88

Fitting Size PXX

Piece Number

Take - Out, A

P08 9062379 2.98

Fitting Size PXX-YY

Piece Number

Take - Out, A

P16-1 9061683 0.96

P20-1-1/2 9061685 0.93

P24-2 9061654 0.95

P32-2 9062280 1.15

Fitting Size PXX

Piece Number

Take - Out, A

P08 9061256 0.85

P12 9061255 0.91

P16 9061254 1.04

P20 9061299 1.11

P24 9061253 1.22

P32 9061252 1.29

P48 9062178 2.63


SS40-RTJ1500-PXX

Flanges, Clean in Place, Caps

SS40-CAP-PXX

SS40-CIP-PXX-YY


SS40-FLNG600-PXX




Fitting Size PXX

Piece Number

Take - Out, A

P08 9062350 2.05

P12 9062351 1.84

P16 9062352 1.83

P20 9062353 2.08

P24 9062354 2.09

Fitting Size PXX

Piece Number

Take - Out, A

P08 9062345 2.05

P12 9062346 1.84

P16 9062347 1.83

P20 9062348 2.08

P24 9062349 2.09

Fitting Size PXX

Piece Number

Take - Out, A

P04 9061608 1.02

P06 9061607 0.95

P08 9060180 0.98

P12 9061212 0.82 *

P16 9061007 1.25

P20 9061294 1.42

P24 9061213 1.56

P32 9061227 1.86

P48 9061678 2.63

P48** 9061725 2.63

Fitting Size PXX

Piece Number

Take - Out, A

P04 9061393 1.15

P06 9061394 1.15

P08 9060040 1.13

at manufacturer's option

SS40-SAE61KIT-PXX

SS40-SAE61-PXX

**Elbow with zinc plated carbon steel drive rings is available at lower cost

SAE61KIT, SAE61, 45 Elbows, 90 Elbows

SS40-EL45-PXX

SS40-EL90-PXX

* Dimension of 1.13 may be furnished



Fitting Size PXX

Piece Number

Take - Out

P12 9061209 1.88 *

P16 9061210 1.88

P20 9061295 2.30

P24 9061211 2.68

P32 9061226 3.48

P48 9061676 5.13

P48** 9061724 5.13

Fitting Size PXX-XX FPT

Piece Number

Take - Out, A

Take - Out,, B

Thread NPT

P08 - 0.5 9061865 1.13 2.44 1/2 - 14

P24 - 0.5 9061833 1.09 1.16 1/2 - 14

Fitting Size PXX

Piece Number

Take - Out, A

Take - Out, B

C*

P24 9061409 2.68 7.66 2.61

P32 9061958 3.48 8.95 2.91

SS40-TEE-PXX

Fitting Size PXX

Piece Number

Take - Out, A

P04 9061389 1.10

P06 9061390 1.10

P08 9061012 1.13

P12 9061216 1.26

P16 9061217 1.88

P20 9061296 2.30

P24 9061218 2.68

P32 9061225 2.98

P48 9061677 4.00

P48** 9061723 4.00

C* Maximum cut on pipe end

**Tee with zinc plated carbon steel drive rings is available at lower cost

SS40-EL90SR-PXX-XX FPT

**Elbow with zinc plated carbon steel drive rings is available at lower cost

SS40-SEL90-PXX

90 Elbows, 90 Elbow Adapters, Street Elbows, Tees

* Dimension of 1.50 may be furnished

at manufacturer's option

SS40-EL90LR-PXX





Piece Number

Take - Out, A

Take - Out, B

P08-P04 9061561 1.13 1.17

P08-P06 9061609 1.13 1.10

P12-P04 9061562 1.26 1.28

P12-P08 9061242 1.26 1.33

P16-P04 9061565 1.88 2.64

P16-P08 9061243 1.88 2.13

P16-P12 9061223 1.88 2.02

P20-P16 9061300 2.30 2.50

P24-P08 9061743 2.68 2.88

P24-P12 9061346 2.68 2.77

P24-P16 9061245 2.68 2.63

P24-P20 9061361 2.68 2.70

P32-P08 9061566 2.98 2.63

P32-P12 9061362 2.98 2.52

P32-P16 9061246 2.98 2.38

P32-P24 9061247 2.98 3.26

P48-P32 9061682 4.00 3.48

(PIPE TO TUBE REDUCING TEE)

Fitting Size PXX-TYY

Piece Number

Take - Out, A

Take - Out, B

P20-T12 9061791 2.30 2.87

Fitting Size PXX-PYY-PZZ

Piece Number

Take - Out, A

Take - Out, B

Take - Out, C

P08-P04-P08 9061563 1.13 1.17 1.13

P12-P04-P08 9061564 1.26 1.38 1.33

P12-P08-P08 9061570 1.26 1.33 1.33

P16-P12-P08 9061572 1.88 2.02 2.13

P16-P12-P12 9061571 1.88 2.02 2.02

P24-P16-P16 9061569 2.68 3.00 3.00

P32-P20-P20 9062276 2.98 3.79 3.79

P32-P24-P12 9061567 2.98 3.26 2.52


Piece Number

Take - Out, A

Take - Out, B

P24 - P04 9061747 1.88 1.20

P32 - P12 9062134 2.75 1.30

Reducing Tees, Double Reducing Tees, Drop Tees

SS40-DTEE-PXX-PYY

SS40-RRTEE-PXX-PYY-PZZ

SS40-RTEE-PXX-PYY

SS40-RTEE-PXX-TYY


XX XX

YY

XX

ZZ

YY

XX XX

YY


[3/8 OD X 0.035 WALL TUBE DROP]

Fitting Size PXX

Piece Number

Take - Out, A

Take - Out, C

P12 9062004 0.98 3.63

Fitting Size PXX

Piece Number

Take - Out, A

Take - Out, C

P16 9061695 1.09 1.78

P20 9061696 1.31 1.94

Fitting Size PXXTYY

Piece Number

Take - Out, A

Take - Out, B

Take - Out, C

P16-T16 9061697 1.09 0.90 1.78

[1/2 OD X 0.049 WALL TUBE DROP]

Fitting Size PXX

Piece Number

Take - Out, A

Take - Out, C

P08 9061466 0.95 3.52

P16 9062509 1.09 3.81

P20 9061465 1.31 3.98

P24 9062510 1.11 4.10

P32 9061464 1.34 4.32

[3/8 OD CPI DROP*]

Fitting Size PXX

Piece Number

Take - Out, A

Take - Out, C

P16 9061750 1.09 1.77

P20 9062137 1.31 1.93

P24 9062140 1.11 2.06

SS40-TEE-PXX-002

** P16 and P20 Sizes are available without an internal travel stop

Drop Tees

* SWAGELOK is a registered trademark of SWAGELOK CO.

* CPI is a trademark of PARKER HANNIFIN CORPORATION.

SS40-TEE-PXX-005

SS40-TEE-PXX-003

SS-3000-TEE-PXX-TYY-002

SS40-TEE-PXX-001

[3/8 OD SWAGELOK DROP*]




[3/8 OD CPI DROP*] [REDUCER]


Piece Number

Take - Out, A

Take - Out, B

Take - Out, C

P20-P16 9061890 1.31 1.09 1.93

[3/8 OD CPI DROP*] [PIPE TO TUBE]


Piece Number

Take - Out, A

Take - Out, B

Take - Out, C

P16-T16 9061889 1.09 0.90 1.77

[1/2 OD CPI DROP*]

Fitting Size PXX

Piece Number

Take - Out, A

Take - Out, C

P16 9062145 1.09 1.66


Fitting Size PXX

Piece Number

Take - Out, A

Take - Out, C

P20 9061930 1.31 1.83

P24 9061751 1.11 1.96

[1/2" FPT DROP]

Fitting Size PXX

Piece Number

Take - Out, A

Take - Out, C

P24 9062293 1.11 2.73

Drop Tees

SS40-TEE-PXX-013

SS40-RTEE-PXX-PYY-005


SS40-TEE-PXX-008


SS40-TEE-PXX-009



[12mm OD X 1mm WALL TUBE DROP]

Fitting Size PXX

Piece Number

Take - Out, A

Take - Out, C

P12 9061911 0.98 2.72

P16 9061912 1.09 2.88


Piece Number

Take - Out, A

Take - Out, C

P32-P20 9062275 3.78 2.98

P32-P24 9062277 3.26 2.98


Piece Number

Take - Out, A

Take - Out, B

Thread NPT

Across Flats

P20-3/4 9061777 2.30 3.00 3/4-14 1.31

Fitting Size PXX-YY SAE

Piece Number

Take - Out, A

Take - Out, B

Thread

P08-9/16 SAE 9061606 1.13 1.81 9/16-18 UNF-2B

Fitting Size PXX

Piece Number

Take - Out, A

P12 9061781 1.26

SS40-RTEE-PXX-YY SAE

*Drop conforms to SAE J1926/1

Drop Tees, Obtuse Tees, Tee Adapters, Cross

SS40-RTEE-PXX-YY FPT

SS40-TEE-PXX-026

SS40-OBTEE-PXX-PYY

SS40-CROSS-PXX




Drop Tees

Page 4Caps, 45 Elbows, 90 Elbows, 45 Tees

Reducing Tees, Drop Tees Page 5

Page 6

Page 1

Page 2

Page 3

General Information

Coupling, Reducers

Adapters, Clean in Place

SS-3000 / SS40STAINLESS STEEL TUBE FITTINGS


www.lokring.com Copyright 2003 Lokring Technology Corporation, All Rights Reserved. 6.06 SS-3000 & SS40 Stainless Steel Tube Fittings (01-28-04)

Fitting Size (TXX)

Qualified Wall Thickness



Install, B

Outside Diameter, C

Inside Diameter, D


Before a Bend, E

1/4" (T04) 0.035 - 0.065 0.88 0.73 0.54 0.257 1.25

3/8" (T06) 0.035 - 0.065 1.26 0.92 0.72 0.382 1.63

1/2" (T08) 0.035 - 0.065 1.34 1.00 0.87 0.507 1.63

5/8" (T10) 0.035 - 0.065 1.53 1.12 1.05 0.632 2.00

3/4" (T12) 0.035 - 0.065 1.56 1.17 1.17 0.757 2.00

7/8" (T14) 0.065 - 0.065 1.50 1.13 1.20 0.882 2.00

1" (T16) 0.065 - 0.083 1.61 1.22 1.38 1.007 2.00

1 1/4" (T20) 0.065 - 0.109 2.06 1.53 1.81 1.257 2.50

1 1/2" (T24) 0.065 - 0.120 2.14 1.60 2.11 1.507 2.75

2" (T32) 0.065 - 0.083 2.65 1.96 2.56 2.007 3.25


General Information

1. All dimensions are in inches.

2. Dimensions A, B, C, D & E are applicable to all fittings of the same size within this catalog.

3. For use on 316, 316L, 304 and 304L seamless and welded stainless steel tube as per ASTM A269 or A213. See table for qualified wll thickness.

4. For tooling dimensions refer to appropriate catalog.

5. Coupling "thru-bore" design permits tube to pass completely through (except SS40-T04). All other fittings (tees, elbows etc.) have an internal travel stop.

6. Material 316L Stainless Steel as per ASTM A276 or ASTM 479.

7. Fittings from T04-T12 & T32 are SS40-Txx. Fittings from T14-T24 are SS-3000-Txx




www.lokring.com Copyright 2003 Lokring Technology Corporation, All Rights Reserved. 6.06 SS-3000 & SS40 Stainless Steel Tube Fittings (01-28-04), Page 1 of 12

Fitting Size TXX

Piece Number

Take - Out

*1/4" (T04) 9061800 0.04

3/8" (T06) 9061796 n/a

1/2" (T08) 9061797 n/a

5/8" (T10) 9061798 n/a

3/4" (T12) 9061799 n/a

7/8" (T14) 9040094 n/a

1" (T16) 9040072 n/a

1 1/4" (T20) 9040047 n/a

1 1/2" (T24) 9040046 n/a

2" (T32) 9062143 n/a

(DOUBLE CONTAINMENT COUPLINGS)

Fitting Size TXX

Piece Number

Span A

T08 9060190 3.53

T10 9040060 3.57

Fitting Size TXX-TYY

Piece Number

Take - Out, A

T06-T04 9061990 1.16

T08-T04 9061779 0.97

T08-T06 9061722 0.70

T10-T08 9061982 0.74

T12-T08 9060624 0.64

T12-T10 9061983 0.74

T14-T12 9061984 0.71

T16-T12 9062014 1.34

T16-T14 9061985 0.84

T20-T16 9061986 0.90

T24-T16 9060653 1.00

T24-T20 9061987 0.84

T32-T20 9062297 1.13

T32-T24 9062119 1.43

(PIPE TO TUBE REDUCERS]


Piece Number

Take - Out, A

P12-T12 9062256 0.66

P16-T08 9041866 0.64

P20-T20 9062149 0.84

P20-T24 9061347 0.84

P32-T32 9062102 1.19

SS40 & SS-3000-RED-PXX-TYY

SS40-DC-TXX

Coupling, Reducers

SS40 & SS-3000-CPL-TXX

*1/4" (T04) Fitting is made with a travel stop to aid with assembly.

SS40 & SS-3000-RED-TXX-TYY



Fitting Size XXSAE-TYY

Piece Number

Take - Out, A

Across Flats

0.25-T04 9061834 1.01 0.75

0.38-T06 9061835 0.92 0.94

0.50-T08 9061836 1.09 1.13

0.63-T10 9061837 1.25 1.25

0.75-T12 9061825 1.35 1.44

0.88-T14 9061826 1.28 1.44

1.00-T16 9061827 1.50 1.63

1.25-T20 9061828 1.46 2.00

1.50-T24 9061829 1.66 2.25

Fitting Size TXX-37FYY

Piece Number

Take - Out, A

Across Flats

0.25-T04 9061839 1.17 0.50

0.38-T06 9061840 1.15 0.63

0.50-T08 9061841 1.26 0.81

0.63-T10 9061842 1.49 0.94

0.75-T12 9061843 1.78 1.13

0.88-T14 9061844 1.88 1.25

1.00-T16 9061845 1.93 1.38

1.25-T20 9061846 2.31 1.69

1.50-T24 9061847 3.00 2.00


Piece Number

Take - Out, A

Take - Out, B

Take - Out, C

T08 - 0.50 9062124 1.16 0.50 0.96

T12 - 0.75 9062123 1.29 0.75 1.02

T16 - 1.00 9062122 1.57 1.00 1.30

Fitting Size TXX-YY

Piece Number

Take - Out, A

T16-1 9061005 0.85

T20-1 1/2 9062274 1.04

T24-1 1/2 9061687 1.04

T32-2 9041891 0.97

Fitting Size PXX-YY

Piece Number

Take - Out, A

P16-1 9061683 0.96

P20-1-1/2 9061685 0.93

P24-2 9061654 0.95

P32 9062280 1.15

SS40-CIP-PXX-YYCIP FITTINGS [PIPE]

Adapters, Clean in Place

1 1/16 - 12 UN

1 3/16 - 12 UN

1 5/16 - 12 UN

1 5/8 - 12 UN

SS40 & SS-3000-ADPT-TXX-37FYY

Thread

7/16 - 20 UNF

1 7/8 - 12 UN

SS40 & SS-3000-ADPT-TXX-TYY

SS40 & SS-3000-CIP-TXX-YY

Threaded end conforms to SAE J514 (37 Flare)

7/16 - 20 UNF

1 7/8 - 12 UN

3/4 - 16 UNF

7/8 - 14 UNF

9/16 - 18 UNF

SS40 & SS-3000-ADPT-XXSAE-TYY

9/16 - 18 UNF

3/4 - 16 UNF

Threaded end conforms to SAE J1926/1 (O-ring straight adaptor)

7/8 - 14 UNF

1 1/16 - 12 UN

1 3/16 - 12 UN

1 5/16 - 12 UN

1 5/8 - 12 UN

Thread



Fitting Size TXX

Piece Number

Take - Out, A

T16 9062298 0.42

T20 9062299 0.42

T24 9061199 0.42

T32 9062144 0.49

Fitting Size TXX

Piece Number

Take - Out, A

T06 9061968 1.18

T08 9061969 1.09

T10 9061970 0.90

T12 9061971 1.04

T14 9061992 1.17

T16 9061993 1.39

T20 9061994 1.26

T24 9061995 1.42

T32 9061996 2.08

Fitting Size TXX

Piece Number

Take - Out, A

T06 9061959 1.20

T08 9061892 1.01

T10 9061960 1.05

T12 9061961 1.41

T14 9061962 1.55

T16 9061874 2.02

T20 9060216 1.88

T24 9060218 2.29

T32 9060575 3.71

Fitting Size TXX-TYY-TZZ

Piece Number

Take - Out, A

Take - Out, B

T24-T20-T20 9061719 1.05 n/a

T24-T24-T24 9061718 0.93 2.93

Fitting Size TXX-TYY-ZZ TUBE

Piece Number

Take - Out, A

Take - Out, B

Take - Out, C

T20-T16-3/8 9061795 0.43 3.26 3.71

* Lateral 3/8 OD X 0.035 wall tube

SS40-LAT45-TXX-TYY-ZZ TUBE

SS40 & SS-3000-CAP-TXX

Caps, 45 Elbows, 90 Elbows, 45 Tees

SS40 & SS-3000-EL45-TXX

SS40 & SS-3000-EL90-TXX

SS-3000-LAT45-TXX-TYY-TZZ


XX YY

ZZ

XX YY

ZZ


Fitting Size TXX

Piece Number

Take - Out, A

T06 9061866 1.15

T08 9061599 0.96

T10 9061965 1.05

T12 9061790 1.41

T14 9061966 1.31

T16 9061736 1.30

T20 9060217 1.88

T24 9060219 2.29

T32 9062109 3.21


Piece Number

Take - Out, A

Take - Out, B

T06-T04 9061991 1.15 1.42

T08-T06 9061972 0.96 1.15

T10-T08 9061973 1.05 1.24

T12-T10 9061974 1.17 1.34

T14-T12 9061975 1.31 1.17

T16-T08 9061686 1.30 1.53

T16-T12 9061809 1.30 1.17

T16-T14 9061976 1.30 1.31

T20-T16 9061977 1.88 2.02

T24-T16 9062250 2.29 2.94

T24-T20 9061978 2.29 2.29

T32-T24 9061979 3.21 3.22

(PIPE TO TUBE REDUCING TEE)


Piece Number

Take - Out, A

Take - Out, B

P20-T12 9061791 2.17 2.74

Fitting Size TXX-TYY-TZZ

Piece Number

Take - Out, A

Take - Out, B

Take - Out, C

T24-T16-T16 9062251 2.29 2.94 2.94

T24-T16-T24 9062252 2.29 2.94 2.29

Reducing Tees, Drop Tees

SS40 & SS-3000-RTEE-TXX-TYY

SS40-RTEE-PXX-TYY

SS-3000-RRTEE-TXX-TYY-TZZ

SS40 & SS-3000-TEE-TXX


XX

ZZ

YY

XX XX

YY

XX XX

YY


Fitting Size TXX

Piece Number

Take - Out, A

Take - Out, C

T08 9060286 0.83 3.26

T10 9061056 0.89 3.33

T12 9061057 0.89 3.40

T14 9061058 0.85 3.43

T16 9061059 0.90 3.54

T20 9060165 0.94 3.70

T24 9060164 0.96 3.86

T32 9062104 0.98 4.08


Piece Number

Take - Out, A

Take - Out, B

Take - Out, C

T08-T06 consult Lokring 0.83 0.82 3.26

T10-T08 9060288 0.89 0.83 3.33

T12-T10 9061060 0.89 0.89 3.40


T14-T12 9061061 0.85 0.89 3.43

T16-T12 9061062 0.90 0.89 3.54

T16-T14 9061063 0.90 0.85 3.54

T20-T16 9060167 0.94 0.90 3.70


T24-T20 9060166 0.96 0.94 3.86


T32-T24 9062106 0.98 0.96 4.08

( 3/8 OD X 0.035 WALL TUBE DROP ) [PIPE]

Fitting Size PXX

Piece Number

Take - Out, A

Take - Out, C

P12 9062004 0.98 3.63

Fitting Size TXX

Piece Number

Take - Out, A

Take - Out, C

T08 9060287 0.83 1.21

T10 9061050 0.89 1.29

T12 9061051 0.89 1.36

T14 consult Lokring 0.85 1.40

T16 9060979 0.90 1.51

T20 9060298 0.94 1.68

T24 9060299 0.96 1.85

T32 9062103 0.98 2.07

Drop Tees

( 3/8 OD X 0.035 WALL TUBE DROP )

SS40 & SS-3000-RTEE-TXX-TYY-001

SS40 & SS-3000-TEE-TXX-001( 3/8 OD X 0.035 WALL TUBE DROP )

SS40 & SS-3000-TEE-TXX-002( 3/8 OD SWAGELOK DROP*)


SS40-TEE-PXX-001




Piece Number

Take - Out, A

Take - Out, B

Take - Out, C

T08-T06 9061658 0.83 0.81 1.21

T10-T08 9060285 0.89 0.83 1.29

T12-T10 9061053 0.89 0.89 1.36


T14-T12 9061054 0.85 0.89 1.40

T16-T12 9061055 0.90 0.89 1.51

T16-T14 9060980 0.90 0.85 1.51

T20-T16 9060391 0.94 0.90 1.68

T24-T16 9061657 0.96 0.90 1.85

T24-T20 9060301 0.96 0.94 1.85


T32-T24 9062105 0.98 0.96 2.07

Fitting Size PXX

Piece Number

Take - Out, A

Take - Out, C

P16 9061695 1.09 1.78

P20 9061696 1.31 1.94

Fitting Size PXXTYY

Piece Number

Take - Out, A

Take - Out, B

Take - Out, C

P16-T16 9061697 1.09 0.90 1.78

Fitting Size TXX

Piece Number

Take - Out, A

Take - Out, C

T08 9061016 0.83 3.26

T10 9061008 0.89 3.33

T12 9061017 0.89 3.40

T14 9061018 0.85 3.44

T16 9061019 0.90 3.55

T20 9060397 0.94 3.72

T24 9061020 0.96 3.88

T32 9062111 0.98 4.10

Drop Tees



( 3/8 OD SWAGELOK DROP*)


SS-3000-TEE-PXX-TYY-002( 3/8 OD SWAGELOK DROP*) [PIPE TO TUBE]

SS40-TEE-PXX-002( 3/8 OD SWAGELOK DROP*) [PIPE]





Piece Number

Take - Out, A

Take - Out, B

Take - Out, C


T10-T08 9060368 0.89 0.83 3.33

T12-T10 9061027 0.89 0.89 3.40


T14-T12 9061028 0.85 0.89 3.44

T16-T12 9061029 0.90 0.89 3.55

T16-T14 9061030 0.90 0.85 3.55

T20-T16 9061031 0.94 0.90 3.72


T24-T20 9061032 0.96 0.94 3.88


T32-T24 9062117 0.98 0.96 4.10

( 1/2 OD X 0.049 WALL TUBE DROP ) [PIPE]

Fitting Size PXXPiece

NumberTake - Out,

A Take - Out, C

P08 9061466 0.95 3.52

P16 9062509 1.09 3.81

P20 9061465 1.31 3.98

P24 9062510 1.11 4.10

P32 9061464 1.34 4.32

Fitting Size TXX

Piece Number

Take - Out, A

Take - Out, C

T08 9061065 0.83 1.21

T10 9061066 0.89 1.29

T12 9061067 0.89 1.36

T14 9061068 0.85 1.40

T16 9061069 0.90 1.51

T20 9061070 0.94 1.68

T24 9061071 0.96 1.85

T32 9062112 0.98 2.07


Piece Number

Take - Out, A

Take - Out, B

Take - Out, C


T10-T08 9061076 0.89 0.83 1.29

T12-T10 9061077 0.89 0.89 1.36


T14-T12 9061078 0.85 0.89 1.40

T16-T12 9061079 0.90 0.89 1.51

T16-T14 9061080 0.90 0.85 1.51

T20-T16 9061081 0.94 0.90 1.68


T24-T20 9061082 0.96 0.94 1.85

T32-T20 9062116 0.98 0.94 2.07

T32-T24 9062115 0.98 0.96 2.07

Drop Tees




( 3/8 OD CPI DROP*)


SS40 & SS-3000-TEE-TXX-005( 3/8 OD CPI DROP*)


SS40-TEE-PXX-003



( 3/8 OD CPI DROP*) [PIPE]

Fitting Size PXX

Piece Number

Take - Out, A

Take - Out, C

P16 9061750 1.09 1.77

P20 9062137 1.31 1.93

P24 9062140 1.11 2.06

( 3/8 OD CPI DROP*) [REDUCER] [PIPE]


Piece Number

Take - Out, A

Take - Out, B

Take - Out, C

P20-P16 9061890 1.31 1.09 1.93

( 3/8 OD CPI DROP*) [PIPE TO TUBE]


Piece Number

Take - Out, A

Take - Out, B

Take - Out, C

P16-T16 9061889 1.09 0.90 1.77


Drop Tees


SS40-TEE-PXX-005

SS40-RTEE-PXX-PYY-005

** P16 and P20 Sizes are available without an internal travel stop



Fitting Size TXX

Piece Number

Take - Out, A

Take - Out, C

T08 9061085 0.83 1.04

T10 9061086 0.89 1.14

T12 9061087 0.89 1.22

T14 9061088 0.85 1.26

T16 9061089 0.90 1.38

T20 9061090 0.94 1.56

T24 9061091 0.96 1.73

T32 9062113 0.98 1.96


Piece Number

Take - Out, A

Take - Out, B

Take - Out, C


T10-T08 9061096 0.89 0.83 1.14

T12-T10 9061097 0.89 0.89 1.22

T14-T10 9061198 0.85 0.89 1.26

T14-T12 9061098 0.85 0.89 1.26

T16-T12 9061099 0.90 0.89 1.38

T16-T14 9061100 0.90 0.85 1.38

T20-T16 9061101 0.94 0.90 1.56


T24-T20 9061102 0.96 0.94 1.73


T32-T24 9062114 0.98 0.96 1.96

( 1/2 OD CPI DROP*) [PIPE]

Fitting Size PXX

Piece Number

Take - Out, A

Take - Out, C

P16 9062145 1.09 1.66

Fitting Size TXX

Piece Number

Take - Out, A

Take - Out, C

T08 9061033 0.83 1.04

T10 9061034 0.89 1.14

T12 9061035 0.89 1.22

T14 9061036 0.85 1.26

T16 9061037 0.90 1.38

T20 9060618 0.94 1.56

T24 9061038 0.96 1.73

T32 9062107 0.98 1.96

Drop Tees

SS40 & SS-3000-TEE-TXX-009( 1/2 OD SWAGELOK DROP*)


SS40 & SS-3000-TEE-TXX-008( 1/2 OD CPI DROP*)



( 1/2 OD CPI DROP*)


SS40-TEE-PXX-008





Piece Number

Take - Out, A

Take - Out, B

Take - Out, C


T10-T08 9060381 0.89 0.83 1.14

T12-T10 9061044 0.89 0.89 1.22


T14-T12 9061045 0.85 0.89 1.26

T16-T12 9061046 0.90 0.89 1.38

T16-T14 9061047 0.90 0.85 1.38

T20-T16 9061048 0.94 0.90 1.56


T24-T20 9061049 0.96 0.94 1.73



( 1/2 OD SWAGELOK DROP*) [PIPE]

Fitting Size PXX

Piece Number

Take - Out, A

Take - Out, C

P20 9061930 1.31 1.83

P24 9061751 1.11 1.96

Fitting Size TXX

Piece Number

Take - Out, A

Take - Out, C





T16 9061197 0.90 5.55


T24 9060978 0.96 5.90



Piece Number

Take - Out, A

Take - Out, B

Take - Out, C



T12-T10 9061196 0.89 0.89 5.38


T14-T12 9061195 0.85 0.89 5.43

T16-T12 9061194 0.90 0.89 5.55

T16-T14 9061193 0.90 0.85 5.55



T24-T20 9062393 0.96 0.94 5.90




Drop Tees




( 1/2 OD SWAGELOK DROP*)


SS40-TEE-PXX-009



1/ NPT DROP [PIPE]

Fitting Size PXX

Piece Number

Take - Out, A

Take - Out, C

Thread

P24 9062293 1.11 2.73 1/2-14

( 12mm OD X 1mm WALL TUBE DROP ) [PIPE]

Fitting Size PXX

Piece Number

Take - Out, A

Take - Out, C

P12 9061911 0.98 2.72

P16 9061912 1.09 2.88

Fitting Size TXX-YY FPT

Piece Number

Take - Out, A

Take - Out, B

Thread NPT

T20-1" 9061780 1.76 2.61 1-11.5


SS-3000-TEE-TXX-YY FPT

Drop Tees

SS40-TEE-PXX-013

SS40-TEE-PXX-026




TEL.: (905) 639-4050 FAX: (905) 639-6163

__________________________________________________________________www.lokring.com

Pipe Sizes Tool Kits Part Number

1/4" NPS (P04) Consult LOKRING Representative -

3/8" NPS (P06) Consult LOKRING Representative -

1/2" NPS (P08) MTK45-SS4/MAS-P08/P12/P16-FR 9080177

3/4" NPS (P12) MTK45-SS4/MAS-P08/P12/P16-FR 9080177

1" NPS (P16) MTK45-SS4/MAS-P08/P12/P16-FR 9080177

1" NPS (P16) MTK60-MAS/SS4-P16/P24/P32-FR 9080135

1 1/4" NPS (P20) Consult LOKRING Representative -

1 1/2" NPS (P24) MTK60-MAS/SS4-P16/P24/P32-FR 9080135

2" NPS (P32) MTK60-MAS/SS4-P16/P24/P32-FR 9080135

3" NPS (P48) ITK-100-MAS/SS4-P48 9080196

Notes : Each Multiple Tool Kit (MTK) consists of one LOKTOOL head, inserts for each size, multipurpose gage for each size and material (SS and CS), 5-Step Installation Guide, and indelible marking pen in a rugged, lightweight case.

Other Individual Tool Kit and Multiple Tool Kit options are available, consult your LOKRING representative or see the installation procedure for additional options

Standard Tooling Selectionfor Carbon Steel MAS-3000

and Stainless Steel (CRES) SS40 Pipe Fittings


www.lokring.com Copyright 2003 Lokring Technology Corporation, All rights reserved 7.01 Standard Tooling Selection for MAS and SS Pipe Fittings (03-17-03)


TEL.: (905) 639-4050 FAX: (905) 639-6163

___________________________________________________________________________www.lokring.com

Tube Sizes Individual Tool Kits Part Number Multiple Tool Kits Part Number

ITK10-SS4-T04 9080199 Consult LOKRING Representative -ITK04 9080212

3/8" (T06) ITK10-SS4-T06 MTK20-SS4-T06/T08 9080223

Documents

Lokring Process Catalog