LITTLE WONDER®

OWNER’S MANUAL and SAFETY INSTRUCTIONSfor Single-Edged (Models 1910, 2410, 3010, 1912, 2412, 3012)

and Double-Edged (Models 1920, 2420, 3020, 1922, 2422, 3022)

Electric Hedge Trimmers

GB

WARNING DANGERBLADES ARE EXTREMELY SHARP.

TO AVOID INJURY WHEN UNPACKINGTHE HEDGE TRIMMER,

DO NOT GRASP THE BLADES.

!!

TABLE OF CONTENTSPage

I. IMPORTANT INFORMATION

A. Introduction .......................................................................................................2

II. GENERAL SAFETY RULES ............................................................................................3A. Safety labels .......................................................................................................4B. Safety symbols identification ...........................................................................4C. Special safety rules ............................................................................................5D.Warnings — dont’s .............................................................................................5E. Warnings — do’s.................................................................................................5

III. UNPACKING AND ASSEMBLY INSTRUCTIONS ..............................................................6

IV. OPERATIONA. Instructions for proper operation .................................................................6-7

V. MAINTENANCEA. Lubrication.........................................................................................................7B. Service maintenance guide................................................................................7

VI. SERVICEA. Trouble-shooting ...............................................................................................8B. Blade adjustment................................................................................................8

VII. PARTS DESCRITIONS ..........................................................................................9-13

VIII. SPECIFICATIONS ..................................................................................BACK COVER

LIMITED SERVICE & WARRANTY POLICY........................................................BACK COVER

I. IMPORTANT INFORMATION

A. INTRODUCTION

On behalf of everyone at Little Wonder, wewould like to thank you for your purchase of aLittle Wonder Electric Powered HedgeTrimmer. This professional trimming machinewas designed to the highest standards to ensureyou many hours of uninterrupted service.

This manual provides the informationnecessary for safe and efficient operation andservice. For your safety, it is criticallyimportant that you read and understand thisentire manual before operating your hedgetrimmer.

2

3

Warning: When using electric tools, basic safetyprecautions, including the following, should always befollowed to reduce the risk of fire, electric shock andpersonal injury.

Read all these instructions before operating thisproduct and save these instructions.

For safe operations:11)) KKeeeepp wwoorrkk aarreeaa cclleeaann..

Cluttered areas and benches invite injuries.22)) CCoonnssiiddeerr wwoorrkk aarreeaa eennvviirroonnmmeenntt..

Do not expose power tools to rain. Do not usepower tools in damp or wet locations. Keep workarea well lit. Do not use power tools where thereis risk of fire or explosion.

33)) GGuuaarrdd aaggaaiinnsstt eelleeccttrriicc sshhoocckk..Avoid body contact with earthed or groundedsurfaces e.g. pipes, radiators, stoves, ovens,refrigerators.

44)) KKeeeepp cchhiillddrreenn aawwaayy..Do not let visitors touch the tool or extensioncord. All visitors should be kept away from area.

55)) SSttoorree iiddllee ttoooollss.. When not in use, tools should be stored in a dry,high or locked up place, out of reach of children.

66)) DDoo nnoott ffoorrccee tthhee ttooooll..It will do the job better and safer at the rate forwhich it was intended.

77)) UUssee tthhee rriigghhtt ttooooll..Do not force small tools or attachments to do thejob of a heavy duty tool. Do not use tools forpurposes not intended; for example, do not usecircular saws to cut tree limbs or logs.

88)) DDrreessss pprrooppeerrllyy..Do not wear loose clothing or jewellery that canbe caught in moving parts. Rubber gloves and non-skid footwear are recommended when workingoutdoors. Wear protective hair covering to containlong hair.

99)) UUssee ssaaffeettyy ggllaasssseess..Use face or dust mask if the cutting operation isdusty.

1100)) DDoo nnoott aabbuussee tthhee ccoorrdd..Never carry the tool by the cord or yank it todisconnect if from the socket. Keep the cord awayfrom heat, oil and sharp edges.

1111)) SSeeccuurree wwoorrkk..Use a vice to clamp the frame bar while adjustingblades. It is safer than using your hand and it freesboth hands to operate the tools.

1122)) DDoo nnoott oovveerrrreeaacchh..Keep proper footing and balance at all times.

1133)) MMaaiinnttaaiinn ttooooll wwiitthh ccaarree..Keep cutting tools sharp and clean for better andsafer performance. Follow instructions forlubrication and changing accessories. Inspect toolcord periodically and if damaged have it repairedby an authorized service facility. Inspect extensioncords periodically and replace, if damaged. Keephandles dry, clean and free from oil and grease.

1144)) DDiissccoonnnneecctt ttoooollss..When not in use, before servicing and whenchanging accessories such as blades, bits andcutters.

1155)) RReemmoovvee aaddjjuussttiinngg kkeeyyss aanndd wwrreenncchheess..Form the habit of checking to see that keys andadjusting wrenches are removed from the toolbefore turning it on.

1166)) AAvvooiidd uunniinntteennttiioonnaall ssttaarrttiinngg..Do not carry a plugged in tool with a finger on theswitch. Ensure switch is off when plugging in.

1177)) UUssee oouuttddoooorr eexxtteennssiioonn lleeaaddss..When tool is used outdoors, use only extensioncords intended for outdoor use.

1188)) SSttaayy aalleerrtt..Watch what you are doing . Use common sense.Do not operate tool when you are tired.

1199)) CChheecckk ddaammaaggeedd ppaarrttss..Before further use of the tool, a guard or other partthat is damaged should be carefully checked todetermine that it will operated properly andperform its intended function. Check foralignment of moving parts, free running of movingparts, breakage of parts, mounting and any otherconditions that may affect its operation. A guardor other part that is damaged should be properlyrepaired or replaced by an authorized servicecenter unless otherwise indicated in thisinstruction manual. Have defective switchesreplaced by an authorized service facility. Do notuse the tool if the switch does not turn it on andoff.

2200)) WWaarrnniinngg..The use of any accessory or attachment, otherthan those recommended in this instructionmanual, may present a risk of personal injury.

2211)) HHaavvee yyoouurr ttooooll rreeppaaiirreedd bbyy aa qquuaalliiffiieedd ppeerrssoonn..This electric tool conforms to relevant safetyrequirements. Repairs should only be carried outby qualified persons using original spare parts,otherwise this may result in considerable dangerto the user.

II. GENERAL SAFETY RULES

WWAARRNNIINNGG DDAANNGGEERRIIFF TTRRIIMMMMEERR IISS UUSSEEDD IIMMPPRROOPPEERRLLYY OORR SSAAFFEETTYY PPRREECCAAUUTTIIOONNSS AARREE NNOOTT FFOOLLLLOOWWEEDD,,

TTHHEE UUSSEERR RRIISSKKSS SSEERRIIOOUUSS IINNJJUURRYY TTOO TTHHEEMMSSEELLVVEESS AANNDD OOTTHHEERRSS.. RREEAADD AANNDD UUNNDDEERRSSTTAANNDD TTHHEE RRUULLEESS FFOORR SSAAFFEE OOPPEERRAATTIIOONN AANNDD AALLLL

IINNSSTTRRUUCCTTIIOONNSS IINN TTHHIISS MMAANNUUAALL..

A. SAFETY LABELS AND MOLDED SYMBOLS

Important parts of the safety system incorporated inboth single-edged and double-edged trimmers are thewarning and informational labels and molded-insymbols found on various parts of the trimmer. These

labels must be replaced in time due to abrasion, etc. Itis your responsibility to replace the labels when theybecome hard to read. The locations of these labels andtheir part numbers for ordering are shown below. Seepage 13 for their part numbers when orderingreplacements.

4

B. SAFETY SYMBOLS IDENTIFICATION

Single-Edged Trimmer Double-Edged Trimmer

GuardRear handle

On/Off switches

Loop handle

Guard

On/Off switch On/Off switch

Safety symbols(Molded into Part No. 310400 Main Housing Set)

Rear handle

WHAT THE SYMBOLS MEAN:1. Read the instructions.2. Do not expose to rain.3. Remove plug from main (electric

power source) immediately if cable isdamaged or cut.

4. Double insulated.

1 2 3 4

WARNING DANGERTO REDUCE THE POTENTIAL FORACCIDENTS, COMPLY WITH THESAFETY INSTRUCTIONS IN THIS

MANUAL. FAILURE TO COMPLY MAYRESULT IN SERIOUS PERSONAL

INJURY AND OR EQUIPMENT ANDPROPERTY DAMAGE.

WARNING DANGERTHIS SYMBOL POINTS OUT

IMPORTANT SAFETY INSTRUCTIONS.

WHEN YOU SEE THIS SYMBOL, HEED IT’S WARNING!!

STAY ALERT!!

! !

!

! !

!

!

! !

Side handleSerial number label

C. SPECIAL SAFETY RULES

1. Read and understand the owner’s manual. Payparticular attention to all sections regarding safety.

2. Always keep a firm grip on both handles while theblades are moving and/or the motor is running. OnSingle-edged Edged units, the right hand grasps thefront side handle and the left hand grasps the rearhandle. On Double-Edged units, one hand graspsthe front ‘loop’ handle, while the other hand graspsthe rear handle.

BE AWARE!! The blades coast after triggers arereleased or motor is switched off. Make sure bladeshave come to a complete stop before letting go of ahandle.

3. Maintain a firm footing and good balance; do notoverreach while trimming. Before you start to trim,check the work area for obstacles that might causeyou to lose your footing, balance or control of themachine.

4. Keep area clear of children, pets, and bystanders.

D. WARNINGS — DON’TS

Don’t use trimmer with one hand, keep both hands onhandles with fingers and thumbs encircling the handles,while blades are moving, and motor is running.

Don’t overreach or stand on unstable support. Do notstand on the top of a ladder while trimming. Use properequipment for reaching higher heights. Keep a goodfooting at all times.

Don’t ever grasp cutting blades for any reason.

Don’t attempt to clear cut material while blades aremoving, and the motor is running. Never try to remove

jammed material before switching the motor off andmaking sure the blades have stopped completely.

Don’t over-ride safety features.

Don’t allow children or incapable people to operate thistrimmer.

Don’t operate this hedge trimmer while under theinfluence of alcohol or drugs.

Don’t attempt to repair this hedge trimmer. Haverepairs made by a qualified dealer or repairman. Seethat only original Little Wonder parts are used.

5

E. WARNINGS — DO’S

Always read and follow all instructions.

Always stay alert. Watch what you are doing and usecommon sense. Do not operate unit when fatigued.

Always dress properly. Do not wear loose clothing orjewellery, they might get caught in moving parts. Usesturdy proper fitting, non-slip gloves. Gloves reduce thetransmission of vibration to your hands. Prolongedexposure to vibration can cause numbness and otherailments. Wear non-skid foot wear to ensure secure andproper footing.

Always wear ear and eye protection. Eye protectionmut meet applicable CE requirements. To avoid hearingdamage we recommend hearing protection be wornwhenever using the equipment.

Always keep both hands on both handles whentrimmer is running. Severe injuries can result if youtry to use the hedge trimmer with only one hand orwith an insecure grip.

Always keep children, pets, and incapable personsaway.

Always use trimmer properly. Cut only types and sizeof growth described in the Trimming section of thismanual. Overloading or abusing your hedge trimmercan cause premature failure and can result in injury.Use common sense.

Always keep a safe distance between two or moreoperators when working together simultaneously.

Always inspect your unit before each use and ensurethat all handles, guards, safety devices and fasteners aresecure, operating, and in place.

Always maintain and examine your trimmer with care.Follow maintenance instructions given in manual.

Always store trimmer in a sheltered area (a dry place)not accessible to children. The hedge trimmer shouldnot be stored in a house.

!

!

!

A. INSTRUCTIONS FOR PROPER OPERATION

WARNING DANGERBLADES COAST AFTER RELEASING THE

SWITCHES

KEEP A FIRM GRIP WITH ONE HANDON EACH HANDLE WHILE BLADES ARE

MOVING AND/OR MOTOR ISRUNNING.

DO NOT STAND ON THE TOP OF ALADDER WHILE TRIMMING.

MAKE SURE YOUR LADDER OR OTHERSUPPORT IS STABLE AND ON FIRM

GROUND.

KEEP A SURE FOOTING.DO NOT OVERREACH.

IF YOUR TRIMMER BECOMES JAMMED,TURN OFF THE HEDGE TRIMMER.

MAKE SURE BLADES HAVE STOPPEDCOMPLETELY, THEN REMOVE

THE OBSTRUCTION.

III. UNPACKING AND ASSEMBLY INSTRUCTIONS

WARNING DANGER

BLADES ARE EXTREMELY SHARP. TOAVOID INJURY WHEN UNPACKING THEHEDGE TRIMMER, DO NOT GRASP THE

BLADES.

Your Little Wonder hedge trimmer has beenassembled for you at the factory. Before operating be

sure all fasteners are secure, and all guards and safetydevices are in place and operating properly.

WARNING DANGER

IF YOU HAVE ANY QUESTIONS,CONTACT YOUR LOCAL DEALER

IV. OPERATION

WARNING DANGERTHE OPERATOR OF THIS HEDGE TRIMMER IS RESPONSIBLE FOR

ACCIDENTS OR HAZARDS OCCURRING TO HIMSELF, OTHERPEOPLE OR THEIR PROPERTY.

6

Misuse of this Hedge Trimmer will void the warranty.ie: cutting hedges or shrubs over 1.27 cm in diameteror foreign objects such as wires, rocks, or fences.Before trimming check work area for foreign objectssuch as wires, cords, glass, fences, or rocks. Be sure toremove any foreign objects from the work area. Failureto properly maintain this hedge trimmer will void thewarranty.

! !

!!

!!

!! Securing theextension cord.

Bend the extensioncord about 15 cmfrom the plug end.Push that bendthrough the oblongopening in the backof the handle. Thenloop the bend underthe cord retainingclips as shown. Thiswill prevent theextension cord fromdetaching from thehedge trimmer plug.

V. MAINTENANCE

1. Read care and safety instructions carefully beforeattempting to use this trimmer. Only after you arefamiliar with your hedge trimmer and all of itscontrols and the functions should you start thetrimmer.

2. Before plugging into an electric circuit, be sure thatthe voltage supply is as specified on hedge trimmer.Models 1910, 1920, 2410, 2420, 3010, 3020 arerated at 464 watts at 115 volts.Models 1912, 1922, 2412, 2422, 3012, 3022 are ratedat 390 watts at 230 volts.

3. Be sure the switches are in the “off” (not depressed)position before connecting unit to the applicablecurrent. (120V AC or 220V/240V AC.) Do notcarry a plugged -in trimmer with a finger on theswitch.

4. The electricity for this hedge trimmer should besupplied through a Residual current Device (RCD)with a tripping current of not more than 30 mA.These protective devices are also known asresidual current circuit breakers (RCCBs) or Earthleakage circuit breakers (ELCBs).

5. Keep extension cord behind trimmer. Never drape

extension cord over hedge being trimmed. On120V units, use 16 gauge wire extension cord up to30 meters. Over 30 meters, use 14 or heavier gaugewire or extension cord. Cords are available fromyour local Little Wonder dealer. The use of lightgauge lamp cords or sizes lighter than thosespecified above will result in loss of power,possible motor failure, overheating of cord and thepossi-bility of fire.

6. Warning! These trimmers have been designed sothey can only be operated when using both hands.Do not attempt to override this important safetyfeature in any way.

7. Hold trimmer firmly. For Single-Edged Model, keepright hand on side handle and left hand on rearhandle. For Double-Edged Model, you can placeeither hand on either handle. Squeeze both switches.Tilt trimmer so cutting tooth is angled slightlytowards the hedge or shrub and proceed to cut.Use overlapping sweeping motions awayfrom your body to achieve a safe and evencut. The unit is designed to cut any typeof hedge or shrub; however, thickness ofcut should not exceed 1.27 cm inch indiameter.

1/2"

Remove the plug from the socket before carrying out any adjustment, servicing, or maintainence.

B. SERVICE MAINTENANCE GUIDE

Area

Gear housingBladesFastenersLabelsHandlesGuards / safety devices

Maintenance

Check greaseInspect / clean / lubricateInspect / tighten / replaceInspect / replaceInspect / replaceInspect / replace

Frequency

MonthlyAfter each useBefore each useBefore each useBefore each useBefore each use

IMPORTANT- Time intervals shown are maximum. Actual use and your experience will determine thefrequency of required maintenance. 7

1. A few drops of light (No.10) oil should be placed onthe back edge of each blade at each adjustingscrew after approximately every four hours ofnormal operation.

2. To obtain trouble-free trimming, it is necessary tokeep the blades lubricated and clean. The gumthat collects and builds up on the blades can beremoved with 50-50 mixture of kerosene andNo.10 oil. Since a petroleum product can shortenthe life of some plastics, it is necessary to removeexcess oil-kerosene mixture from the plastic parts.Blades must be clean before they can be adjusted.Caution! Kerosene and oil are flammable.

3. A few drops of light (No. 10) or 3-in-1 oil should beput in the hole indicated on the bottom coverplate. This is necessary only at the beginning of aday’s operation.

4. Gear housing and motor bearings have beenpermanently lubricated with a special greasewhich should last for the life of the trimmer. Whenblades are replaced, or any other time that thebottom cover plate is removed, the grease must behecked for proper amount (approximately 3/4 fullin the area of the gears), and a new gasket and newscrews must be used to insure proper seating ofcover plate. Use only Lubrico M3-3K9K grease(P/N 16-78A) in the gear housing. Lubrico M24M(P/N 16-78B) is to be used on the motor bearings.Lubrico is available through your local LittleWonder dealer.

5. Before each use, inspect to be sure handles, safetydevices and fasteners are secure and in place, andcord is not frayed. If the supply cord is damaged, itmust be replaced by the manufacturer, its serviceagent or similarly qualified person in order toavoid a hazard.

A. LUBRICATION AND MAINTENANCE

WARNING DANGERKEEP HANDS AWAY FROM THE BLADES WHILE SERVICING THE HEDGE TRIMMER.

BE SURE TRIMMER IS SECURED, UNPLUGGED, AND BLADES ARE GUARDED WHILE MAKING ADJUSTMENTS

DOUBLE-EDGED

The care and adjustment of the blades is very importantto the efficient operation of the trimmer and especiallyto the long life of the motor.

Make sure the trimmer is NOT plugged in.

1. Turn trimmer upside down. Place trimmer in vice,clamping on the sides of frame bar. Be careful!Blades are sharp!

2. Using a 11 mm wrench (spanner) , loosen all bladelocknuts and unscrew the large head screws by twoturns.

3. Starting with the screw nearest the gear housing,

tighten the screw until the blade guard of theSingle-Edged trimmer or the protective comb of the Double-Edged trimmer can just be moved withfinger pressure. (A .004 mm(1 1/2 thou) feeler gaugejust slips under the blade guard or comb whenproperly adjusted.) Tighten the locknuts whileholding the screw stationary in its correct adjustedposition. Re-check to make sure the blade guard orcomb can still be moved.

4. Repeat Step 3 on each screw in turn until all arecorrectly adjusted.

NOTE: CORRECT BLADE ADJUSTMENT CANONLY BE ACHIEVED ON CLEAN, OILED BLADES.

B. BLADE ADJUSTMENT

SINGLE-EDGED

8

A. TROUBLE-SHOOTING

Problem

1. Blades don’t cut cleanly.

2. Blades don’t move whenturned on.

3. Excessive electrical arcingfrom vents in top oftrimmer.

Remedy

Have blades sharpened andadjusted.

Re-adjust blades followingservice instructions.

Replace brushes - followservice instructions.

Cause

Blades are dull or not adjustedproperly.

Blades are adjusted too tight.

Worn brushes.

VI. SERVICE

! !

Single-Edged assembly

9

KKeeyy NNoo.. PPaarrtt NNoo.. DDeessccrriippttiioonn QQttyy..1 310100 12 16-54B 72 16-54B 62 16-54B 53 310106 14 NA 15 310310 15 310305 15 310300 16 30-2 16 24-2 16 19-2 17 30-1 17 24-1 17 19-1 18 310215 19 16-93 59 16-93 49 16-93 3

10 16-54A 410 16-54A 310 16-54A 211 3036-B 312 310505 1

Gear housing assembly (including pressed in pins)Nut lock 1/4-28 whiz flange (for models 3010, 3012) 30” SENut lock 1/4-28 whiz flange (for models 2410, 2412) 24” SENut lock 1/4-28 whiz flange (for models 1910, 1912) 19” SEFrame bar supportSide handle sssembly (See individual part numbers)Frame bar assembly (for models 3010, 3012) 30” SEFrame bar assembly (for models 2410, 2412) 24” SEFrame bar assembly (for models 1910, 1912) 19” SEInside blade (for models 3010, 3012) 30” SE Inside blade (for models 2410, 2412) 24” SEInside blade (for models 1910, 1912) 19” SE Outside blade (for models 3010, 3012) 30” SEOutside blade (for models 2410, 2412) 24” SEOutside blade (for models 1910, 1912) 19” SEConduitBlade guard (for models 3010, 3012) 30” SEBlade guard (for models 2410, 2412) 24” SEBlade guard (for models 1910, 1912) 19” SELarge head phillips screw (for models 3010, 3012) 30” SELarge head phillips screw (for models 2410, 2412) 24” SELarge head phillips screw (for models 1910, 1912) 19” SE1/4-28 Flange locknutScrew, 1/4-28 x 1” large head

Double-Edged assembly

10

KKeeyy NNoo.. PPaarrtt NNoo.. DDeessccrriippttiioonn QQttyy..1 310100 12 16-54B 72 16-54B 62 16-54B 53 300300 14 NA 15 310325 15 310320 15 310315 16 30-2D 16 24-2D 16 19-2D 17 30-1D 17 24-1D 17 19-1D 18 30-42 18 24-42 18 19-42 19 16-54A 49 16-54A 39 16-54A 2

10 310500 211 310505 1

Gear housing assembly (including pressed in pins)Nut Lock 1/4-28 whiz flange (for models 3010, 3012) 30” DENut Lock 1/4-28 whiz flange (for models 2410, 2412) 24” DENut Lock 1/4-28 whiz flange (for models 1910, 1912) 19” DEFrame bar supportLoop handle assembly (See individual part numbers)Frame bar assembly (for models 3010, 3012) 30” DEFrame bar assembly (for models 2410, 2412) 24” DEFrame bar assembly (for models 1910, 1912) 19” DEInside blade (for models 3010, 3012) 30” DE Inside blade (for models 2410, 2412) 24” DEInside blade (for models 1910, 1912) 19” DE Outside blade (for models 3010, 3012) 30” DEOutside blade (for models 2410, 2412) 24” DEOutside blade (for models 1910, 1912) 19” DE30” Comb (for models 3010, 3012) 30” DE24” Comb (for models 2410, 2412) 24” DE19” Comb (for models 1910, 1912) 19” DELarge head phillips screw (for models 3010, 3012) 30” DELarge head phillips screw (for models 2410, 2412) 24” DELarge head phillips screw (for models 1910, 1912) 19” DEScrew, Plas-Tite No. 8 x 3/4”Screw, 1/4-28 x 1” large head

Gear/motor assembly

11

KKeeyy NNoo.. PPaarrtt NNoo.. DDeessccrriippttiioonn QQttyy..1 310100 12 16-57A 13 310407 44 D16-71 15 310111 16 310112 17 16-64 18 16-65 19 16-67 1

10 16-81-1 811 310503 212 3042 413 D16-56F 114 310903 114 310900 115 310108 117 16-69D 118 310901 118 310902 119 16-69E 120 3025 221 310105 222 3026 2

Gear housing assemblyGear housing cover plateGrommet rubberGasket cover plateGear eccentric - (See Note)Gear cluster - (See Note)Connecting rodSpacer connecting rodFeltScrew 6-32 x 5/16Motor bolt 8-32 x 2 1/2Machine screwWear plateStator 120V (for models 3020, 3010, 2420, 2410, 1920, 1910)Stator 230V (for models 3022, 3012, 2422, 2412, 1922, 1912)Motor housing base and cap set with brush holderBearing lowerArmature 120V (for models 3020, 3010, 2420, 2410, 1920, 1910)Armature 230V (for models 3022, 3012, 2422, 2412, 1922, 1912)Bearing upperBrush holder [not shown]BrushBrush retaining plate

Note: New high speed gears. Part number 310111 must be used with part number 310112, andlikewise part number 310112 can only be used with part number 310111.

Double-Edged front loop handle assembly

Single-Edged front handle assembly

12

KKeeyy NNoo.. PPaarrtt NNoo.. DDeessccrriippttiioonn QQttyy..1 3033 12 310405 13 310216 14 310203 15 310207 16 310504 37 310500 28 310307 1

Switch normally openSwitch normally closedLoop handle trigger setLoop handle setShieldScrew Plasti-Tite No. 8 x 1”Screw Plasti-Tite No. 8 x 3/4”Loop handle trigger strap

KKeeyy NNoo.. PPaarrtt NNoo.. DDeessccrriippttiioonn QQttyy..1 310206 12 310210 13 3033 14 310405 15 310502 16 310501 17 310500 38 310200 1

Side handle shieldTrigger side handleSwitch normally openSwitch normally closedNut nylock 1/4-28Socket flat head 1/4-28 x 3/4 ssScrew Plasti-Tite No. 8 x 3/4”Side handle set

Main housing assembly

13

KKEEYY NNOO.. PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN QQTTYY..1 310400 12 310403 13 310404 15 310438 15 310436 15 310439 15 310437 16 310209 17 3033 18 310405 19 310500 610 310504 311 310410 111 310412 111 310414 111 310416 111 310421 112 310600 113 310217 114 420139 1

Main housing setHousing brush cap cover plateHousing loop handle cover plate *PC Board assembly (for models 3012, 2412, 1912)PC Board assembly (for models 3010, 2410, 1910)PC Board assembly (for models 3022, 2422, 1922)PC Board assembly (for models 3020, 2420, 1920)Trigger rear housingSwitch normally openSwitch normally closedScrew, Plasti-tite No. 8 x 3/4”Screw, Plasti-tite No. 8 x 1”120V Cord assembly230V Cord assemblyCord assembly - (UK)Cord assembly - (Switzerland)Cord assembly - (Australia)Warning labelGrommet, Conduit **Conversion Cord (UK) - Not Shown

* Not needed for double-edge models.** Not needed for single-edge models

LIMITED SERVICE & WARRANTY POLICY FOR ELECTRIC HEDGE TRIMMERS

All Little Wonder Electric Hedge Trimmers are guaranteed against defects in material andworkmanship for a period of 2 YEARS from date of purchase, when used for RESIDENTIAL SERVICE, or 1 Year when used for COMMERCIAL SERVICE. Any Little Wonder Electric Hedge Trimmer or partfound to be defective within the warranty period is to be returned to any registered Little Wonder Dealer.

Transportation charges for parts and units submitted for replacement under this warranty must beborne by the purchaser.

THIS WARRANTY shall not be effective if the product has been subject to misuse, negligence oraccident, used in cutting hedges or shrubs greater than 1/2" in diameter, used to cut foreign objectssuch as wire, rocks, or fences, or if the product has been repaired or altered outside of our Southamptonfactory or any registered Little Wonder dealer, in any respect which affects its condition or operation.

LITTLE WONDER shall not be liable for any special indirect or consequential damages arising fromdefective equipment. Any implied warranty, including merchantability of fitness for a particularpurpose, shall not extend beyond the written warranty period.

THIS WARRANTY shall only be effective if the enclosed Warranty/Registration card is properly filledout and returned to Little Wonder, Div. of Schiller-Pfeiffer, Inc. at time of purchase.

LITTLE WONDER®

DIVISION OF SCHILLER-PFEIFFER, INCORPORATED1028 STREET ROAD, P.O. BOX 38

SOUTHAMPTON, PA 18966PHONE 215-357-5110 • FAX 215-357-8045

Specifications. descriptions, and illustrative material in this literature are as accurate as known at the time of publication, but are subject to change without notice.

©2003, LITTLE WONDER, Division Schiller-Pfeiffer, Inc. P/N 3107013-03

VIII. SPECIFICATIONS

Model Cutting Length Weightcm (in.) kg (lb)

1912 48 (19) 3.49 (7.7)

1922 48 (19) 3.89 (8.6)

2412 61 (24) 3.62 (8.0)

2422 61 (24) 4.04 (8.9)

3012 76 (30) 3.85 (8.5)

3022 76 (30) 4.59 (10.1)

All listed hedge trimmers are rated for 230 volts AC at 50 hertz.

The A-weighted emission sound pressure levelat the operator position has been measured at:LPA = 80 dB(A). These measurements weremade in accordance with EN ISO 11201:1996under no-load conditions.

The Hand-Arm weighted r.m.s. vibrationmeasured at the handles in accordance withEN 50144-1 part 13.3 at rated conditions, noload was:1.0 m/s2.

Manufactured by: