Your Guide To Better Pictures......

In Association With:

Studio Flash SystemsProlinca

By: Chris Burfoot A.M.P.A. A.R.P.S. 2003C

....Lighting Techniques For Digital And Film

A Simple Guide To Studio Lighting Techniques

By Chris Burfoot A.M.P.A. A.R.P.S.

What type of light?Traditionally, continuous lighting was always used in studio situations. However, in more recent years and in the vast majority of studios, electronic flash is now the norm.Tungsten (continuous) light has the advantage of being a little less expensive than flash, but unfortunately the many drawbacks out-weigh this.The main problem with tungsten light is that it generates more heat than light, the colour of the light it produces is very yellow and it gets worse as the bulb ages. This means that you have to use either a tungsten balanced film or a filter on your camera to compensate. There is also a very limited range of accessories.Anyone who has spent any time either side of the camera with tungsten light will know all about the heat it produces. This can make your subject very uncomfortable and due to the brightness, causes the iris of the eye to close right down. It is often the case that eyes look more attractive with a larger pupil.

With bright tungsten light the iris closes right

down.

With studio flash the iris does not react fast

enough to be a problem.

The disadvantage of using a standard on-camera type flashgun is that you can’t see the lighting until you get your photos back!Studio flash overcomes this problem by using a modelling lamp which should mimic the light produced by the flash tube. This enables you to set up your lighting with the confidence of being able to see what you

are going to get! - WYSIWYG - What you see is what you get!However, various makes of studio flash have modelling lamps which are not always equal. I have always used the Prolinca/Elinchrom system because of the advantages they give me. Firstly the modelling lamp bulb is exactly in the centre of the flash tube and almost the same size. This means that the modelling light is virtually identical to the flash - WYSIWYG! Another big plus of this system is the huge range of accessories, the secure accessory fitting and the performance of the flash. The flash duration is very fast, typically over 1/2000th sec. This means that not only will it freeze action, but there are no problems mixing the flash with daylight, and using a fast shutter speed. Recycling times are also very fast, generally less than a second! So I never miss a shot! Big problems can occur if your shutter is faster than the flash!

What do I need to buy?You can start off with a very basic outfit. Pictured below is the Prolinca Home Studio starter set. It consists of a flash head, a stand, a reflector and a brolly. We will discuss the use of brollies later, but this will give you the basics to enable you to produce very acceptable portraits of your family or friends.This one head starter kit costs just over £200 + Vat. OK, lets have a brief look at how a studio flash head works and what you can do with this outfit.

1

How does a flash work?If you look at the front of a studio flash head you will see a flash tube - on this Elinchrom example, the tube is the circular one with a modelling lamp in the centre. (The higher output 250w Halolux is fitted to this head.)The modelling lamp provides a continous light so that you can see the effect you are creating.The flash tube on the standard head is horseshoe shaped with a terminal on each end. The glass envelope is filled with a non-conductive gas and wrapped around this is a trigger wire. The flash energy is stored in capacitors within the main body. Voltages are extremly high so never take one apart!When the flash is fired a 25,000 volt charge is run through the trigger wire ionising the gas. This allows the power to pass between the terminals and in doing so, energy is released in the form of heat and light. All this happens in around 1/2000th second!

Let’s take some pictures!I am sure that there are occasions when it is very convenient to pop a flash on top of your camera and yes, this is the way camera manufacturers design them to work. The trouble is that it’s probably the worst place to put it!Light from the camera position causes many problems. Firstly you can see the very unattractive “Red-Eye”. This is

caused by the flash reflecting off the rear surface of the eye. Secondly it gives a heavy shadow on the wall behind the subject and thirdly it has produced a very flat light that shows no shape or

substance to the subject. Because the flash is a very small light source it is also a very hard light source. We will talk later of hard and soft lighting effects.By moving the light around to the side we can achieve two things very easily. Firstly we remove the shadow from the background and secondly we now have a “lit” and an “un-lit” side to Laura’s face.

In this example we have also placed a blue background behind our model. The contrast is now far too high between the two sides of her face but it does tell your brain that she is a 3 dimentional subject rather than a cardboard cut-out!We could now add a second light from the left to fill those shadows. But we must be careful, if our second light was set at the same power we would be back to flat lighting and two sets of shadows!So let’s leave our second light in its box for the moment and use a reflector panel.

Using a reflector panel

In this example we have turned the models’ shoulders away from the camera and added a silver reflector panel to the left side. It is quite amazing how much light can be bounced back. We have still retained a difference in light levels on the left and right of her face keeping the 3D effect.

2

How high should my light be?Generally speaking for flattering lighting, light should come from above. Light from below is very un-natural as you can see! There was a very old camera club rule that nose shadows should go down but should not cut into the lip. I don’t believe in rules for lighting - it depends on what you are trying to achieve. The lighting style above would make a great “evil” theatrical portrait!

Hard Light - Soft LightOne of the basic principals of lighting is that “The bigger the light the softer it is”.You can see from the example that the on camera flash is a very hard light, it is also very small - about 2x1cm! The other photographs so far, have been taken with a studio flash fitted with a 16cm reflector. This has the immediate effect of making the light softer simply because it is bigger. But if we shoot the head into an umbrella we can make our light source bigger still and we can spread the light over a larger area softening it further.Think about nature. In the desert in Africa the Sun is a tiny point source of light and it therefore gives a very hard high contrast light. We all know that the Sun is immense but because it is 93 million miles away, in relation to us it looks very small. On the other hand if we think about a typical summer in the UK where we have cloud cover from horizon to horizon, the whole dome of sky becomes our light source. This gives very soft light with hardly any shadows.

Making Light SofterSo, let’s fit an umbrella onto our light and see what happens. Tip: When using a brolly don’t forget to adjust it so that the modelling light is filling, but is not spilling over the edge of it - don’t waste your light!!

By adding a silver brolly to our head we have increased the diameter of the light from 16cm to 85cm. We are also now using reflected light rather than direct. The light is softer and more flattering. Note that we have still retained the shading on the left and the background has become darker as there is not so much light falling onto it.Silver brollies retain a reasonable amount of contrast and “sparkle”. They are also very efficient so very little light is lost. For a more natual look a white brolly could be used, or, softer still a white translucent one. The translucent brolly can be used in two ways. Either in “shoot through” or reflective modes. Take a look at the following examples.

Adding a second lightWe have seen that by lighting from the side we can make a subject look more three dimentional. But to add that extra depth to the photograph, we should unpack the second head.To give good separation between your subject and the background a second light can be used in two ways. To light the background or to back-light the subject.We have, however, to be careful that the light from the second head goes where we want it to! By fitting a snoot or a honeycomb to the head we can control where the light falls. (see page 8)

3

In the previous example you can see how a splash of light on the background livens the whole picture up and gives more depth. Now let’s turn the second light around and back-light Laura.

You can see how a little light from behind gives separation from the background and brings the hair to life showing its true texture and colour. Hair absorbs light and can look very dull if not lit. The splash of light over Laura’s left shoulder emphasises the fact that she is three dimensional.Of course if you have a third light you can light the background as well or you can back-light from both sides!

Using a main and fill lightIn this next set-up we have replaced our reflector with a “fill” light. Our main or “key” light is fitted with the same silver umbrella and placed at the side position as before. In addition to this we have used our second head, fitted with a translucent, or “shoot through” umbrella. This fill light is placed close to the camera position slightly higher than the subject. It is set to give one f-stop less light than the main light onto the model. This can be easily set up using a flashmeter and by taking readings from each head individually.

e.g. if the main light is giving a reading of f11, the fill should give a reading of f8. Don’t forget to take another reading with both lights and set that as your aperture. By adding a third head as a background light we put that little extra depth into our picture.

Using a Soft BoxSoftboxes are available in the Prolinca and Elinchrom ranges in various sizes from 40cms square up to the amazing Octa which is almost 2 metres across!The most useful sizes for portrait work are the 70cm or 100cm square, although the Prolinca 60x60cm is great value for money and works very well. Remember, the bigger the light the softer it is. To get the softest light from your softbox - get close! If used just out of view of the camera, it will give you a lovely, soft, diffused light. The bigger it is the more “wrap-around” it will be - a 100x100cm was used in these examples.

With and without a white reflector.

Main

Fill

4

As you can see from the diagram, this is the same set-up but with the addition of a back-light which “lifts” the picture from the page.But for a totally different look, let’s try “Butterfly” lighting with the softbox. This is achieved by placing the main light directly in front of the model, but quite high. As you can see this gives light from above, so our shaded side is now underneath her chin. Incidently, this technique is called “Butterfly” lighting because the nose shadow is supposed to resemble one! (I’ve never seen it myself!)

The light from above gives a similar result to the first example in this section. Instead of the left side of Laura’s face being in shadow, it’s now under the eyes, nose and chin where we need some “fill”. By placing a silver reflector on her lap and another either side,or by using a Lastolite “Triflector” we can achieve a superb portrait which emphasises the model’s eyes.

You can totally change the look of a portrait just by changing the background colour and adding a back light! Now we have a completely different look.

Hard and Soft Together!There is no reason why a hard light source cannot be mixed with a soft one. It has the advantage of giving a very flattering effect, but still retaining some “punch”. Have a look at the shots below and before you look at the diagram, see if you can work out where the lights are and what accessories I have used.

The same set-up was used for both photographs. I used just three heads, one softbox, one 21cm reflector and one honeycomb. The set is made very simply with some net curtaining, fur rugs, a beanbag and a few old tea-chests! The

net curtains are threaded onto a child’s hoop which is hung flat to the ceiling.

Draped nets

Honeycomb

MainFill5

For the softest, most flattering lighting, two softboxes will give lovely results.In this case one 100x100cm and one 70x70cm softbox have been combined. As you can see, the main light was placed on the right of the camera and the fill, set at 1 f-stop less was to the left. A third head fitted with a honeycomb was directed at the back of Laura’s head to spill over her shoulder and bring out the detail in her hair.

Shooting with two softboxes

The lighting hasn’t changed! But just look at the difference a change of background has made!

Digital or film?All the examples shown here were taken on a Canon 10D Digital camera.Lighting techniques are the same for film. The real difference with digital is that you don’t need quite as much power, but for both you do need power stability. Throughout this publication, I have used the Elinchrom Style 300S system which offers an amazing power range from 9 up to 300 watt seconds! This also provides stability of +/- 1%, so every exposure is the same and the colour balance will be consistant thoughout.We looked earlier at what you will need to create and control the light. You can find detailed information about the more advanced accessories at the back of this guide.As stated already, you can easily start with a simple one head kit which can then be expanded to match your developing skill and requirements. Elinchrom and Prolinca in particular offer some very effective low cost solutions. But the main advantage of over 25 years experience in the business... is that they can provide every accessory you could ever need to get the job done.

Shooting still-lifeThe techniques used for still-life are just the same as those shown for portraits. Lighting to show shape and form is from one side. In this set-

up a 70x70 softbox has been placed at one side to give the effect of light through a window. A reflector panel on the right bounces the light back to fill the shadow side.The easiest way to photograph products with a shadowless background is to use the Colorama Mini-Cove which can be painted any colour you like.

6

Using a Flashmeter - don’t panic!

The first thing to do is to set your camera to manual! It doesn’t matter how clever your camera is, you can’t use it on “auto” with studio flash!You need to set your shutter speed to the syncronisation setting for electronic flash (see your instruction book). If in doubt set it to 1/60th second. This leaves only the aperture to set which will depend on what the ISO rating of your film is. For general studio work, to optimise quality I would recommend you stick to 100 ISO.Next, set the film ISO onto the meter and connect the sync lead between your main light and the PC socket on the meter.For this example let’s say that we are taking a portrait with one light and we are using 100 ISO film. Hold the flashmeter in front of your subject’s face and point it at the light. Press the button on the meter to fire the flash and it will read the light falling on your subject, giving you a recommended aperture. Set this on your camera and fire away! - I told you not to panic! It’s as easy as that.

Use the diffuser cover when reading flash.

Shutter Speed

Sync lead from the flash head plugs into here.

On/Off control.

Mode button and mode display. Used to set Flash/Daylight mode

When the flash is fired correct aperture is shown here.

Set your film speed with this button.

In the picture above I have shown a typical flashmeter and its functions. They will vary from make to make but most are similar in the way their controls function. The meter above also works with ambient light which is very useful if you are combining flash and daylight.

Metering several heads.As we have seen, taking a meter reading from a single head is very simple. But what about when you start using multiple heads? It is actually very straight forward.Let’s say we are using a main light and a second light on the background. The first step is to take a reading from the main light as explained previously and set that as your aperture on your camera. Follow the diagram below to balance subsequent lights.

Learn the rules - so you know how to break them properly!

= Flashmeter (a rather large one!)

Take first reading here and set aperture onto

the camera

Take second reading here to measure light falling on background.

If the reading from the first position is, say, f11 that is what you set on your camera. If the reading from the background light also gives f11 the background will be the same density as the subject.For a lighter background increase the power so that the reading is more than f11 e.g. f16 (= one stop brighter) For a darker background the reading should be f8 (=one stop darker). Tip: If you run out of adjustment on your head it can be moved closer for more light or away for less. - Double the distance = 2 stops less.The same principal applies to hair and back lights. - Easy isn’t it!

7

Lighting accessories.We have already discussed the more popular accessories like honeycombs and snoots let’s take a look at what they do.Snoot:The Snoot produces a hard edged circle of light and is one of the most popular accessories. It is conical in shape and fits onto the front of a head. Mainly used as a backlight or hair light with good tight control.Honeycomb:The honeycomb produces a soft edged circle of light. Mainly used as a back or hair light or for putting

a graduated circle of light onto the b a c k g r o u n d . Many people (including myself) prefer the effect of the honeycomb to

the more harsh effect of the snoot.A variety of honeycombs are available which give different angles of illumination. Honeycombs are often used with coloured filter gels to change the colour of the background.Umbrellas:We have already discussed the various types of umbrellas. To recap: Silver brollies are very efficient, this means very little light loss. They give a punchy sparkle to your pictures. W h i t e r e f l e c t i v e brollies give a natural soft light, which is ideal for children and older people. Translucent (shoot-through) brollies give the softest, most diffused light. However, they are not so efficient. In a small room

the reflected light can add to the fill and pick up colour casts! Softboxes:The softest of all - and the bigger they are the softer they are. Their effect is similar to the shoot-through brolly but the light is much more controlled. For head and shoulder portraits a 60 or 70cm square softbox will work well. For half to t h r e e - q u a r t e r length the 100cm square is better (can even be used for full length if your subject is not too tall)! If you ever get the chance to use an Elinchrom Octa you will be spoilt forever!Focussing Spots:We have all seen the spotlight effect on stage which gives a perfect circle of light. The same system is available for studio flash. Within the Elinchrom and Prolinca ranges there are a number of “spotlight” accessories.The Minispot:This has a focusing lens and a separate holder for “gobos” and filters. “Gobos” are metal discs with

various patterns cut out of them, which can be projected through the spotlight to

give different patterns of light on the subject or background.The 18/36 Zoom Spot:This provides a similar effect to the Minispot but also has a zoom control to vary the angle of illumination. It is supplied with a complete system of accessories including masks, gobos, a filter holder and filters.

8

This is just a small selection of the most popular accessories. Take a look at www.elinchrom.com or the system leaflet for more ideas!

Your Notes

9

Note - Must visit

The Elinchrom

Web Site at

www.elinca.comNote - Check out the On-Line demos onwww.theflashcentre.com

Quick Reference Guide

Page 2. Using One Head and a reflector panel

Page 3. Using one head with a brolly and a reflector panel

Page 3. Using one head with a brolly and a background light with a honeycomb and a reflector panel

Page 4. Using one head with a brolly and a backlight with honeycomb and reflector panel

Main

Fill

Page 4. Using two heads, main and fill

Page 4. Using a softbox and reflector panel

Page 5. Using a softbox with reflector panels

Page 6. Shooting still-life