1

TeraFlex, Inc.5241 South Commerce Dr.

Murray, Utah 84107Phone/801.288.2585

Fax/801.713.2313www.teraflex.biz

PR

OD

UC

T I

NS

TA

LL

AT

IO

N G

UID

E

Rev. 8 December, 2010 TT

JK Budget BoostPart # 1355200Part # 1355210Part # 1255200

Important Notes: THIS INSTRUCTION IS FOR MULTIPLE PART NUMBERS. MAKE SURE THAT YOU LOOK AT THE APPROPRIATE PARTS LIST AND INSTRUCTION STEPS.

For part #1255200 go to page 2For part #1355210 go to page 4For part #1355200 go to page 6

Prior to beginning this or any installation read these instructions to familiarize yourself with the required steps and evaluate if you are experienced and capa-ble to personally perform these modifications. Refer to the parts list to ensure that all necessary components and hardware has been included. If any parts are missing please contact your local retailer for assistance.

Required Tools:10, 14, 15, 16, 17, 18, 19, 21mm sockets and wrenches7/16”, 5/8”, 3/4” sockets and wrenches3/8” &1/2” drive ratchets3”, 6”, & 12” extensionsFt-lbs torque wrenchBreaker barLarge crescent wrenchSlip Joint pliers Power hand drill 3/8” drill bitFloor jackJack standsWheel chocksHammerCenter punchPry barsPliersTape measureSafety glassesPencil or marker

2

PRODUCT INSTALLATION GUIDE

Part # 1255200

Budget Boost Lift WITH SHOCKS

3

134 er fl 7/16 nc 4

1255200 Budget Boost With ShocksComponent Item ID Item Name Qty Per Assy

308 Zerk 1/4 28 4953800 Bumpstop JK Front Upper 2954700 Bumpstop JK Rear Lower 2954202 Bracket Raw Rear Trackbar JK 1754300 Swaybar Link Rear 3 4" 2102 SLEEVE 1" OD x 1 1/8" 1

1954200 Spacer Rear JK 2" 21953200 Spacer Front JK 2.5" 2600276 JK Rear Brakeline Extension Bracket 2553100 JK Front Shock 2554100 JK Rear Shock 2

5018 Nut Bolt RR Ext Bl Kit JK 888HRWBLKJK THB76 Nut 1/4 28 Nylock 277 Bolt 1/4 28 X.75 Hex Zinc 2458 Washer Flat 1/4 4

5019 Nut Bolt RR Bs JK 888HRWBSJK THB38 Washer Flat 5/16 Zink 00038 8153 Bolt 5/16 18X1.25 Hex Zinc 4632 Nut 5/16X18 Stover 4

5020 Nut Bolt Lsx JK 888HRWLSXJK THB134 Washer flat 7/16 zincWash at zi 4165 Nut 12Mm 1.75 Stover Metric Hex Zinc 2401 Bolt 12Mx55M1.75P Zink Metric Hex 2

5114 Nut Bolt pack 888HRWRTBJKBB THB62 BOLT 9/16" 18 UNC x 3" LONG HEX HEAD ZINC PLATED 183 NUT 3/8" 16 UNC STOVER LOCK NUT ZINC PLATED 184 Washer 3/8" FLAT zinc 298 Bolt 3/8 16 UNC x 1 Hex Zinc 1276 NUT 9/16 18 Stover Zinc 1318 Washer 9/16" FLAT Zinc 2

4

PRODUCT INSTALLATION GUIDE

Part # 1355210

Lift kit 2.5” spring lift w/ NO SHOCKS

We recommend using TeraFlex, Elka or Teraflex tuned FOX Shocks with this application. Check the shock length chart on page 8 if you would like to use another shock. DO NOT USE A SHOCK WITH A LONGER EXTENDED Length. This will cause damage to critical items such as brake lines and

drive lines.

Budget Boost Lift WITH SHOCK EXTENTIONS

5

1355210 Budget Boost JK W/Shock Ext.Component Item ID Item Name Qty Per Assy

308 Zerk 1/4 28 4953800 Bumpstop JK Front Upper 2954700 Bumpstop JK Rear Lower 2954202 Bracket Raw Rear Trackbar JK 1754300 Swaybar Link Rear 3 4" 2102 SLEEVE 1" OD x 1 1/8" 1

1954200 Spacer Rear JK 2" 21953200 Spacer Front JK 2.5" 2600276 JK Rear Brakeline Extension Bracket 2554801 JK Shock Extension Driver Rear Upper 1554802 JK Shock Extension Passenger Rear Upper 1319 Washer for JK Front Shock Extension 1.75X.675X.125 2

553800 JK Shock Extension Front 2

5018 Nut Bolt RR Ext Bl Kit JK 888HRWBLKJK THB76 Nut 1/4 28 Nylock 277 Bolt 1/4 28 X.75 Hex Zinc 2458 Washer Flat 1/4 4

5019 Nut Bolt RR Bs JK 888HRWBSJK THB38 Washer Flat 5/16 Zink 00038 8153 Bolt 5/16 18X1.25 Hex Zinc 4632 Nut 5/16X18 Stover 4

5020 Nut Bolt Lsx JK 888HRWLSXJK THB134 Washer flat 7/16 zinc 4165 Nut 12Mm 1.75 Stover Metric Hex Zinc 2401 Bolt 12Mx55M1.75P Zink Metric Hex 2

5022 Nut Bolt RR Shock Ext JK 888HRWRRSXJK THB38 Washer Flat 5/16 Zink 00038 484 Washer 3/8" FLAT zinc 8152 Bolt 5/16 18X1 Hex Zinc 2158 Bolt 10mm1.5px90mm Hex Zinc JK rear shock ext 4632 Nut 5/16X18 Stover 2

5114 Nut Bolt pack 888HRWRTBJKBB THB62 BOLT 9/16" 18 UNC x 3" LONG HEX HEAD ZINC PLATED 183 NUT 3/8" 16 UNC STOVER LOCK NUT ZINC PLATED 184 Washer 3/8" FLAT zinc 298 Bolt 3/8 16 UNC x 1 Hex Zinc 1276 NUT 9/16 18 Stover Zinc 1318 Washer 9/16" FLAT Zinc 2

6

PRODUCT INSTALLATION GUIDE

Part # 1355200

We recommend using TeraFlex, Elka or Teraflex tuned FOX Shocks with this application. Check the shock length chart on page 8 if you would like to use another shock. DO NOT USE A SHOCK WITH A LONGER EXTENDED Length. This will cause damage to critical items such as brake lines and

drive lines.

Budget Boost Lift WITH NO SHOCKS

7

401 lt 12M 55M1 75P Zi 2

1355200 Budget Boost JK PlainComponent Item ID Item Name Qty Per Assy

308 Zerk 1/4 28 4953800 Bumpstop JK Front Upper 2954700 Bumpstop JK Rear Lower 2954202 Bracket Raw Rear Trackbar JK 1754300 Swaybar Link Rear 3 4" 2102 SLEEVE 1" OD x 1 1/8" 1

1954200 Spacer Rear JK 2" 21953200 Spacer Front JK 2.5" 2600276 JK Rear Brakeline Extension Bracket 2

5018 Nut Bolt RR Ext Bl Kit JK 888HRWBLKJK THB76 Nut 1/4 28 Nylock 277 Bolt 1/4 28 X.75 Hex Zinc 2458 Washer Flat 1/4 4

5019 Nut Bolt RR Bs JK 888HRWBSJK THB38 Washer Flat 5/16 Zink 00038 8153 Bolt 5/16 18X1.25 Hex Zinc 4632 Nut 5/16X18 Stover 4

5020 Nut Bolt Lsx JK 888HRWLSXJK THB134 Washer flat 7/16 zinc 4165 Nut 12Mm 1.75 Stover Metric Hex Zinc 2401 Bolt 12Mx55M1 75P Zink Metric HexBo x . nk Metric Hex 2

5114 Nut Bolt pack 888HRWRTBJKBB THB62 BOLT 9/16" 18 UNC x 3" LONG HEX HEAD ZINC PLATED 183 NUT 3/8" 16 UNC STOVER LOCK NUT ZINC PLATED 184 Washer 3/8" FLAT zinc 298 Bolt 3/8 16 UNC x 1 Hex Zinc 1276 NUT 9/16 18 Stover Zinc 1318 Washer 9/16" FLAT Zinc 2

8

8

3

2

7

6

1

5

4

1954202JK REAR TRACKBAR BRACKET KIT FOR 2"-3" OF LIFT

REVISIONS

ZONE REV. DESCRIPTION DATE APPROVED

A 14MM HARDWARE CHANGED TO 9/16" 5/2/2008 AF

ITEM NO. PART NUMBER DESCRIPTION QTY.1 954202 BRACKET REAR TRACKBAR JK BUDGET BOOST 12 102 SLEEVE 1" OD x 1-1/8" LONG JK BUDGET BOOST REAR TRACKBAR 13 98 BOLT 3/8"-16 UNC x 1" LONG HEX HEAD CAP SCREW ZINC PLATED 14 84 WASHER 3/8" FLAT WASHER ZINC PLATED 2

5 83 NUT 3/8"-16 UNC STOVER LOCK NUT ZINC PLATED 1

6 62 BOLT 9/16" -18 UNC x 3" LONG HEX HEAD ZINC PLATED 17 318 WASHER 9/16" FLAT ZINC PLATED 28 276 NUT 9/16"-18 STOVER LOCK NUT ZINC PLATED 1

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF TERA MANUFACTURING. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF TERA MANUFACTURING IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

DIMENSIONS ARE IN mmTOLERANCES:FRACTIONAL 1/32NO PLACE DECIMAL 0.8ONE PLACE DECIMAL 0.4TWO PLACE DECIMAL 0.1

MATERIAL

FINISH

-

ZINC

DRAWN

DATENAME TERA MANUFACTURING5251 COMMERCE DRIVE

MURRAY, UTAH 84107

SIZE

BDWG. NO. REV

SCALE: 1:2

UNLESS OTHERWISE SPECIFIED:

A

A.FLEGAL

-

8 NOV 2007

SHEET 1 OF 1

1954202DO NOT SCALE

DRAWING

FOR JK BUDGET BOOSTREAR FRAME SIDE

ANGULAR: MACH 1 BEND 2

HEAT TREATMENT

CHECKED - -

WEIGHT

Kg

DROP TRACKBAR BRACKET

Rear — Loop-LoopemShock Application Information Front — St -Loop

Front Part Number Rear Part NumberVeh

Licleift

ShockManufacture

ExteLe

Anded

ngth(in)

BTravel

(in)Com

Cpressed

Length(in)

DUnloadedBushing

Height (in)

EExtended

Length(in)

FTravel

(in)

GCompressed

Length(in)

JKWrangler

2007-Current

1553100 1554100 JK with 2.5" of Lift TeraFlex 24.880 9.470 15.410 0.750 24.990 9.360 15.630

1460125 1400125 JK with 2.5" of Lift ELKA 24.800 9.409 15.389 0.850 25.000 9.530 15.470

1553200 1554200 JK with 3-4"of Lift TeraFlex 26.880 10.380 16.500 0.750 28.090 10.840 17.250

1982820 1982819 JK with 2.5-4" of Lift FOX 26.400 10.900 15.500 0.696 27.650 11.200 16.450

Compressed LengthG

Extended LengthE

TravelF

Loop-Loop Shock Dimension

Compressed LengthC

Extended LengthA

TravelB

Unloaded Bushing HeightD

Stem-Loop Shock Dimension

9

Installation:Remove track bar bolts using a 21mm socket, 1. at both the front and rear axle and remove track bars.

Loosen all control arm bolts using a 21mm 2. socket, DO NOT REMOVE ARMS OR BOLTS!Lift the vehicle and support under the frame 3. with jack stands. Make sure that the axle will drop far enough to remove and install the coil springs.Remove the wheels.4.

Rear Installation:Support the rear axle with a jack and slightly. 5. Lift one or two inches so that it is easy to remove the bolts from the shocks and sway bar links. (If you remove the nut from the bolt prior to jacking up on the axle you can put slight pressure on the bolt with your hand while jacking the axle and see where it is easiest to remove the bolts.)Remove shocks using an 18mm socket and 6. wrench for the axle side bolt and a 16mm socket for frame side.

Remove sway bar links using an 18mm socket 7. and wrench, make sure to put aside for use in the front of the vehicle.

Remove the clips that secure the ABS wiring 8. harness to the upper control arm mount.

10

Disconnect the brake line bracket at the frame 9. using a 10mm socket. DO NOT DISCONNECT THE BRAKE LINES FROM THE CALIPERS.

Remove and discard the bracket that holds the 10. park brake cables to the body using a 10mm deep well socket.

Carefully lower the rear axle far enough to 11. remove the rear springs. Be careful not to let the coils fall out as you lower the axle. Lower the axle far enough to install the new 2.5” spacer in place. While lowering the axle make sure the brake lines, ABS wires and axle vent do not stretch as this could cause damage to these vital parts.

Install new rear track bar drop bracket. Use the 12. template in the instructions to mark and drill the 3/8” hole needed for proper installation.

Install your new track bar drop bracket using 13. the 14mm bolt, washer, and nut. Place the sleeve provided inside the bracket to prevent crushing the bracket. Install track bar in the new bracket. Torque outside bolt to 45 ft-lbs and bolt with sleeve to 125 ft-lbs. Do not torque the track bar until the vehicle is on the ground. (In some cases the new bracket will not fit in the factory bracket. In this case use a pry bar or crescent wrench to spread the bracket so the new drop bracket aligns perfectly with the factory track bar hole. DO NOT DRILL OUT HOLE TO MAKE FIT. This can cause slop in the bracket and be heard as a popping sound.

11

Install new rear bump stop spacer by placing 17. the spacer on the axle pad lining up both holes with the overhang part of the pad facing forward. Use the provided 5/16” x 1 ¼” bolts with 5/16” washers and 5/16” nuts. Tighten with 1/2” wrenches.

Install the factory isolater onto the new TeraFlex 14. rear spacer.Install the new spacer into the frame. You should feel or hear a poping and the spacer should stay hanging from the frame.

Re-install the factory springs.15. Install new rear sway bar links on the inside of 16. the sway bar and the inside of the axle bracket. Use the factory bolt on the axle side with the nut on the outside so excess threads will not interfere with the shock. Use the provided 12mm bolt and washer for the swaybar side with the 12mm nut and washer on the inside to give the most possible room for tire clearance. Torque to 75 ft-lbs.

Install shocks. If shock adapters are included 18. in your kit, install shock adapters and shocks. Note: The shock adapters are different from left to right. Make sure you are installing the correct one. There are two 10mm X 90mm and one 5/16” X 1” bolts for each side. Use the 5/16 X 1” bolt to align the adapter in its proper location leave loose. Start one of the 10mm x 90mm bolts a few threads then slide shock bar pin around bolt and install the other bolt using a 16mm socket. Use a 1/2” wrench to tighten the small bolt. Torque the top shock bolts to 37 ft-lbs, and the bottom bolt to 56 ft-lbs.

12

Install rear brake line extensions provided in 19. the kit. Bolt the bracket to the factory brake line bracket by removing the 10mm bolt and installing the bracket in that location with the bend of the bracket going flush with the frame. NOT STICKING OUT AWAY FROM THE FRAME. Torque to 14 ft-lbs. (If bracket gets installed the wrong way it will rub on your tires) Then use the supplied hardware to attach the factory bracket to the drop bracket by using 1/2” socket and wrench.

Remove jack from under axle.20. Rear installation complete.21.

Front installation: Place jack under the axle and slightly lift the 22. front axle so you can easily remove factory hardware form shocks, sway bar links.Remove the front shocks by using a 18mm 23. wrench and socket at the axle side and a 16mm wrench for the frame side. (If the shock spins with the top nut you can use a 5/8 wrench to hold the shock just below the shock mount. Ratchet wrenches are best for the top nut)

13

Using grease, lube the bump stop extension to 28. install it into the spring tower. (You may need a piece of wood or equivalent to put in between the extension and the coil perch and jack up the axle to install extension. Do one side at a time.

Use grease to lube the yellow bump stop and 29. install it into the extension.

Install the factory coil springs. Do the drivers 30. side first.

Remove sway bar links using 18mm socket 24. and wrench at the axle and 18mm socket and 20mm wrench at the sway bar. Lower the jack enough to remove the springs.

Remove front coil springs.25. Remove the stock yellow bump stop with a pair 26. of channel lock pliers.Remove the factory isolater and install the 27. new TeraFlex spacer fallowed by the factory isolater.

14

If your kit comes with the shock adapters install 31. the front upper shock adapter by spinning it onto the factory shock using red thread locker . Then install the provided washer then the original rubber bushing with the big hole in it and use the other one on the upper side of the frame and install in the same order it was removed. Torque to 20 ft-lbs on the frame side and 56 ft-lbs on the axle side. Install factory 32. rear sway bar links in the front on the outside of the sway bar and inside of the axle mount. Torque to 75 ft-lbs.

Reinstall wheels, torque lug nuts to 95- 115 33. ft-lbs, Remove jack stands, lower the vehicle onto its own weight, and torque all the control arm bolts. Torque the uppers to 75 ft-lbs and the lowers to 125 ft-lbs. Install the rear track bar. To align the rear track 34. bar to the axle have someone push on the body of the jeep until the bolt hole lines up. Torque to 125 ft-lbs. Install the front track bar. To align the front 35. track bar have someone move the steering wheel until the bolt hole lines up. Torque to 125 ft-lbs.To straighten the steering wheel, loosen the 36. adjuster sleeve on the drag link by using 15mm sockets. Mark the position by making a line across the sleeve and the threads this line will indicate the original position. Looking from the drivers side rotate the adjuster sleeve counter clockwise 3/4 of a turn. This should get your steering wheel close to center. Every vehicle is different so test drive yours and determine if yours needs further adjustment. Once steering wheel is straight torque pinch clamp bolts to 45 ft-lbs.

Re-torque all fasteners after 300 miles.37.

15

Cut this template out and bolt it on the outside of the factory track bar bracket. Use tape to ensure that the template does not move and center punch the top hole for the new TeraFlex track bar drop bracket.

TeraFlex Track Bar Bracket Template

16

MAINTENANCE INFORMATION:It is the buyer’s responsibility to have all suspension, drivetrain, steering, and other components checked for proper tightness and torque after the first 100 miles and every 3000 miles after that.

NOTICE TO INSTALLER: The enclosed “Warning to Driver” sticker must be installed in the vehicle in driver’s view. This sticker is to act as a constant safety reminder when operating the vehicle. It is your responsibility as the equipment installer to install the provided sticker and to forward the product instructions to the vehicle’s owner for review. If a “Warning to Driver” sticker or product installation guide were not included in the kit, FREE replacement stickers and instructions are available by request. It is the installer’s duty to ensure a safe and controllable vehicle after the modifications have been performed.

WARNING: Neither the seller nor the manufacturer will be liable for any loss, damage, or injury directly or indirectly arising from the use of or inability to determine the use of these products. Before using, the user shall determine the suitability of the products for its intended use, and the user shall assume all responsibility and risk in connection therewith.

WARNING TO DRIVER: This vehicle has been modified to enhance off road performance and has unique handling characteristics. Use in harsh environments can cause extreme stress on the components. Vehicle should be inspected after being off road to make sure that all the components are in working order and safe to travel on the highway. All fasteners should be checked so that they are at the correct torque specifications as the vibration and stresses from off roading may cause critical fasteners to work loose. Extra care should be taken to inspect the critical components, steering, and brake systems. During each oil change components such as arms, tie rod ends, etc should be greased and checked for excessive wear. Any worn components should be replaced. When returning to the pavement always set or restore tire air pressure to the factory recommendation and connect or engage any disabled sway bar mechanisms. Because of the higher center of gravity and larger tires, this vehicle handles and reacts differently than many passenger cars, both on and off road. You must drive it safely! Extreme care should be taken to prevent vehicle rollover or loss of control, which can result in serious injury or death. Avoid sudden sharp turns or abrupt maneuvers. Generally, braking performance and capabilities are decreased when significantly larger/heavier tires are used, especially when used in combination with transfer case low-range reduction kits. Take this into consideration while driving. Do not add, alter or fabricate any factory or aftermarket parts to increase vehicle height over the intended height of the TeraFlex product purchased. Mixing component brand is not recommended. TeraFlex Inc. will not be responsible for any altered product or any improper installation or use of our products. We will be happy to answer any questions concerning the design, function, and correct use of our products. It is ultimately the buyer’s responsibility to have all bolts/nuts checked for tightness after the first 100 miles and then every 3000 miles. Wheel alignment, steering system, suspension and drive line systems must be inspected by a qualified professional mechanic at least every 3000 miles.

TERAFLEX PRODUCT WARRANTY: Tera Manufacturing warrants TeraFlex Suspension products to the original retail purchaser to be free of defects in material and workmanship for as long as the original purchaser owns the vehicle on which products were originally installed. Failure to complete regular maintenance (grease every 3000 miles) on TeraFlex FlexArms will void this warranty. All other conditions of the standard TeraFlex product warranty apply. All TeraLow products are covered by TeraFlex’s two (2) year warranty to be free of defects in material and workmanship for two years from date purchased. Tera axles are covered by a 12-month warranty to be free of defects in materials and workmanship. This warranty does not cover or include product finish, improperly installed or applied products, improperly maintained products, products or components used for racing or competition or damage due to abuse or neglect, products that fail due to the use of larger tire and wheel combinations. All returns must be accompanied by an original invoice. It is the customer’s responsibility to remove the product from the vehicle. Shipping charges are the responsibility of the customer. Tera Manufacturing will pay the return freight if the product meets the terms of warranty. This warranty is for the replacement or repair of defective TeraFlex products only and does not include freight charges, labor charges for removal of or installation of TeraFlex or related products or components, costs incurred due to down time of the vehicle, or lost profits due to vehicle down time. A returned goods authorization number (RGA#) must accompany any returned products. For more information please contact a TeraFlex customer service representative.

COPYRIGHT©Copyright 2008. All rights reserved, TeraFlex Inc. Reproduction of this catalog and/or any of its contents without written permission is strictly prohibited.TeraFlex® is a registered trademark of TeraFlex Inc. All trade names and logos including but not limited to TeraFlex, FlexArms, RockGuard, Monster, and LCG are protected by law and duplication of trade names and/or logos are strictly prohibited.TeraFlex Inc. reserves the right to update, discontinue, redesign, modify finish, part number or component build parts if deemed necessary without written notice. TeraFlex Inc., and any associated dealers are not responsible for misprints or typographical errors that may have inadvertently been made within this instruction sheet.

Jeep® and the Jeep® grill are registered trademarks of Chrysler LLC, and have no affiliation with TeraFlex Inc.

PRODUCT INFORMATION& WARRANTY

TeraFlex, Inc. 5241 South Commerce Dr. Murray, Utah 84107Phone/801.288.2585 Fax/801.713.2313 www.teraflex.biz