Intelligent Power Switches

(IPS)

Contents

4 Technology Overview

IPS solutions 6 Product range 9 Transceiver ICs 10 Power stage characteristics

4

IntegrationLogicinterface

Driver &protection

Logic interface + driver + protections + power switches

BENEFITS • Increased system reliability• Part count reduction• Space saving• Built-in protection• System approach

Feedback

From a discrete solution To an intelligent solution

Powerswitches

ST offers an industrial series of intelligent power switches (IPS) for high-side and low-side configurations. An IPS integrates a control part (logic interface, drivers, and protection) with a power stage.

IPS are based on the well-consolidated bipolar, multi-power BCD and VIPower®M0 technologies.

Devices in development are designed using the latest versions of the above technologies, thus offering state-of-the-art solutions in a wide range of applications.

FEATURES• Galvanic isolation on chip• Supply voltage up to 60 V• Fast demagnetization of inductive loads• Very low R

DS(ON) supply current• Short-circuit and overcurrent protection• Undervoltage protection and overvoltage

shutdown• Loss of ground protection• Thermal protection: junction and case• Diagnostic output• Open load detection• Designed to meet IEC 61131-2 standards

Technology Overview

5

Typical architecture of intelligent power switch (VNI8200XP)

International standards

IPS devices are designed to safely drive every kind of load in low-voltage applications (up to 60 V), handling data in and out of the microcontroller by means of status/input signals. IPS devices are designed to comply with the following international standards for EMC and PLC equipments:

Packages

Technological evolution has led to smaller IPS devices, housed in tiny, flat, no-lead plastic packages (DFN, QFN). The high thermal capacitance of the power packages such as PowerSO-36, PowerSSO36, PowerSSO24, PowerSSO12 and HTSSOP20, allows the absorption of high-energy pulses when an inductive load is driven without any external freewheeling diode.

Concerning ISO8200B, ISO8200AQ and ISO8200BQ, they are designed to comply with the following international standards for isolation characteristics and tests:

X8

FB

SDO / IN8

CLK / IN6

Output 1..8

VCC

WD / IN4

OUT_EN / IN3

WD_EN / IN2

SDI / IN5

SEL1 / IN1

SEL2

BOOT

PHASE

VregROW COL

DCVDD VREF

SPIparallel

watchdog

DC / DCconverter

LEDdriving

Case tempdetection

Junction tempdetection

VCC- Voutclamp

Current lim.

VCCclamp

Undervoltagedetection

Logic

PG214321 GNDFAULT TWARN

SS / IN7

• IEC 61000-4-4 (electrical fast transient/burst)• IEC 61000-4-2 (ESD, immunity test contact/air)• IEC 61000-4-5 (surge test immunity requirements)• IEC 61000-4-6 (current injection test)

• IEC 61131-2 (programmable controller, equipment requirements and tests)

• UL 1577 (isolation voltage)• IEC 61000-4-8 (power frequency magnetic field immunity

test)

• IEC 60747-5-2 (optoelectronic devices characteristics)

• I/O Safety limits according to VDE V 0884-11• UL 508 (Standard for Safety for Industrial Control

Equipment)

6

Output Stage

Part numberOutput Chan-nels

Output current / Channel

(lnom) (A)

Typ. RDS(on) Ohm

Supply voltage (V) AMR max.

Supply voltage (V) min.

Note Package Evaluation BoardApplication Note/

User Manual

High-side

IPS160H

1

2 0.06 65 8Open Load Diag PowerSSO-12 STEVAL-IFP028V1 AN4781

IPS160HF (*) Open Load Diag PowerSSO-12 X-NUCLEO-OUT08A1 UM2715IPS161H

0.5 0.06 65 8Open Load Diag PowerSSO-12 STEVAL-IFP034V1 AN4998

IPS161HF (*) Open Load Diag PowerSSO-12 X-NUCLEO-OUT10A1 UM2716L6370D 2 0.1 50 9.5 Adjustable IOUT PowerSO-20L6375D

0.5 0.4 50 8 SO-20

L6375S SO-8L6377D Adjustable IOUT SO-14

TDE1747FP < 0.5 60 8 Adjustable IOUT SO-14TDE1798DP

0.550 6 mini-DIP8

TDE1897RFPT0.4 50 18

SO-20 AN453TDE1898CFP SO-20 AN453TDE3247FP < 0.5 36 8 Adjustable IOUT SO-14VN540SP-E

20.05 45 10 PowerSO-10

VN751PT 0.0645 5.5

Open Load Diag PPAK STEVAL-IFP005V2VN751S 0.06 Open Load Diag SO-8

VNI2140J 2 1 0.06 45 9 Open Load Diag PowerSSO-12 STEVAL-IFP010V3 AN2985L6376D

4

0.50.64 50 9.5 PowerSO-20

VN330SP-E 0.2 45 10 PowerSO-10VN340SP-33-E 1 0.2 45 10 PowerSO-10 AN2208

VN340SP-E0.5

0.2 45 10 Per Channel Diag PowerSO-10 AN2208VNI4140K 0.08 41 10.5 Per Channel Diag PowerSO-24 AN2684

VNI4140K-32 1 0.08 41 10.5 Per Channel Diag PowerSO-24 STEVAL-IFP019V1 AN4009VNQ860-E

< 0.5 0.2741 5.5 Per Channel Diag SO-20

VNQ860SP-E 41 5.5 Per Channel Diag PowerSO-10

ISO8200AQ (**)

8

0.50.11 45 10.5

Isolated, SPI, Per Channel Diag

QFN 9x11 X-NUCLEO-OUT02A1 UM2507

ISO8200B (**) 0.11 45 10.5 Isolated PowerSO-36 STEVAL-IFP015V2 AN4373, UM2209

ISO8200BQ (**) 0.5 0.11 45 10.5 Isolated QFN 9x11STEVAL-IFP033V1

X-NUCLEO-OUT01A1AN4373, UM2209

VN808-32-E1

0.15 45 10.5 PowerSO-36 AN2443, AN2208VN808CM-32-E 0.16 45 10.5 PowerSO-36 STEVAL-IFP001V1 AN2443, AN2208

VN808CM-E

0.5

0.16 45 10.5 Logic level Inputs PowerSO-36 AN2443, AN2208VN808-E 0.15 45 10.5 PowerSO-36 AN2443, AN2208

VNI8200XP 0.11 45 10.5LED Matrix Driver, DCDC,

SPI, Per Channel DiagPowerSO-36

STEVAL-IFP022V1 X-NUCLEO-PLC01A1

AN4284, UM1918

VNI8200XP-32 1 0.11 45 10.5LED Matrix Driver, DCDC,

SPI, Per Channel DiagPowerSSO-36 STEVAL-IFP032V1 AN4862

High & Low side

TDE1708DFT (***)1

< 0.5 50 6 DFN 8L 4x4 STEVAL-IFS006V2AN2679, AN2813

TDE1707BFP (***) 0.5 50 6 SO-8 AN1213, AN495

Low side

IPS4260L

4

0.5 0.26 55 8Adjustable IOUT, Open

Load / Per Channel DiagHTSSOP-20 STEVAL-IFP029V1 UM2297

Push-Pull

L6374FP < 0.5 4 50 10.8 Push-Pull Line Driver SO-20

Notes : (*) Satisfy SIL applications requirements for interface type C (or D) Class 3 (**) Galvanic Isolated (***) The TDE1707 and TDE1708 are specific IPS developed to match all types of industrial detectors. They can be coupled with inductive, capacitive, ultra-sonic or optical detectors and can be used in high-side or in low-side driver configuration in 3-wire networks.

IPS solutions Product range

7

ISO8200B

STEVAL-IFP015V2

STEVAL-IFP005V2X-NUCLEO-OUT08A1

VN751PTIPS160HF

STEVAL-IFP010V3X-NUCLEO-OUT10A1

VNI2140JIPS161HF

STEVAL-IFP028V1

IPS160H

ISO8200BQ

STEVAL-IFP033V1

IPS161H

STEVAL-IFP034V1

IPS4260L

ISO8200AQ

STEVAL-IFP029V1

X-NUCLEO-OUT02A1

ISO8200BQ

X-NUCLEO-OUT01A1

VNI8200XP

STEVAL-IFP022V1STEVAL-IFP019V1

VNI4140K-32 VNI8200XP

X-NUCLEO-PLC01A1

VNI8200XP -32

STEVAL-IFP032V1

Quad Channel

Single Channel

Octal Channel

Dual Channel

Isolated IPS

8

GUI Software on PC(e.g. STSW-IPS16X)

IPS Evaluation Board(e.g. STEVAL-IFP034V1) Load

STEVAL-PCC009V2microcontroller based

interface board

USB SPI/GPIOs

Evaluation software STSW-IFAPGUI Expansion board plugged on the Nucleo board (i.e. Nucleo pack)

USB

EVALUATION BOARD BASIC SETUP

NUCLEO BOARD SETUP

9

Industrial transceiver ICs for IO-LINK and SIO mode

By using a state-of-the-art technology (MultiPower BCD) that allows the design of the logic part and robust LV power MOSFETs allowing hundreds kHz switching frequency in the same chip, ST offers an efficient, compact and cost-effective solution to drive any 3-wire digital sensor. Modern sensors and actuators require:

• remote service• standardization• sensor functionality verification• diagnostics• monitoringThe L6360, L6362A and L6364 I/O industrial transceiver ICs meet all these requirements. These ICs offer the market IO-LINK sensors/actuators that work without special cables. They feature an advanced solution that can even be integrated in old systems, that is neutral to any field bus, and keeps the point-to-point communication. Industrial transceiver ICs are designed in order to guarantee EMC immunity (burst/fast transient, ESD contact/air, surge pulse, RF emission/conduced), according to the IO-LINK specification and SIO mode requirements.

Industrial transceiver IC product range

Part numberSupply

voltage (V)VDD (V)

Output current (A)

Imax linear reg. (mA)

TechnologyOutput

channelsInput

channelsPackage

L6360 (Master) 18 to 32.5 3.3/5 0.5 65 MultiBCD 2 2 QFN 26L 3.5 x 5 mm

L6362A (Device) 7 to 36 3.3/5 0.22 10 MultiBCD 1 1 DFN 12L 3 x 3 mm

L6364Q (Device) 6 to 35 3.3/5 0.25/0.5(**) 50 MultiBCD 2 2 QFN 20L 4 x 4 mm

L6364W (Device)(*) 6 to 35 3.3/5 0.25/0.5(**) 50 MultiBCD 2 2 CSP 19 2.5 x 2.5 mm

Notes: (*) available end of Q4 2020 (**) join mode

IO-Link evaluation boards

Order code DescriptionApplication note / User manual

STEVAL-IDP004V2 IO-Link master multi-port evaluation board based on L6360 AN5041

STEVAL-IOM001V1 IO-Link master evaluation board based on L6360 equipped with ST morpho connectors for STM32 Nucleo UM2414

STEVAL-IDP003V1 IO-Link industrial modular sensor board based on L6362A AN5041

STEVAL-IOD003V1 IO-Link (PHY) device evaluation board based on L6362A with Arduino connectors for STM32 Nucleo UM2424

P-NUCLEO-IOM01M1 STM32 Nucleo pack for IO-Link master based on L6360 device with IO-Link v1.1 (PHY and stack) UM2421

P-NUCLEO-IOD01A1 STM32 Nucleo pack for IO-Link device based on L6362A device fully compatible with IO-Link v1.1.3 (PHY and stack) UM2425

X-NUCLEO-IOD02A1 Expansion board IO-Link device based on L6364Q device fully compatible with IO-Link v1.1 (PHY and stack) UM2741

P-NUCLEO-IOD02A1(*) STM32 Nucleo pack for IO-Link device based on L6364 device fully compatible with IO-Link v1.1 (PHY and stack) UM2782

STEVAL-BFA001V2B Multi-sensor predictive maintenance kit with L6362A and IO-Link stack v.1.1 UM2663

Notes: (*) Available end Q4 2020

IPS Solutions Transceiver ICs

10

L6362A

P-NUCLEO-IOD01A1

L6360

STEVAL-IOM001V1

L6360

STEVAL-IDP004V2

STEVAL-IOD003V1 X-NUCLEO-IOD02A1

L6362A L6364Q

STEVAL-BFA001V2B STEVAL-IDP003V1

L6362A L6362A

L6360

P-NUCLEO-IOM01M1

11

VIPowertechnology SO-20PowerSO-10

50 mΩ

SO-8

60 mΩ

PPAK

60 mΩ

PowerSSO-24

200 mΩ

200 mΩ

270 mΩ 270 mΩ

IPS160H 2A Single HSS

IPS161H 0.5A Single HSS

VN751 2A Single HSS

VN540 2A Single HSS

VN2140J 1A Dual HSS

VN330SP 0.5A Quad HSS

VNQ860 0.25A Quad HSS

VN340SP 0.5A Quad HSS

VNI4140K 0.5A Quad HSS

PowerSSO-12

80 mΩ

60 mΩ

60 mΩ

IPS160HF2A Single HSS

IPS161HF0.5A single HSS

60 mΩ

60 mΩ

80 mΩ

VNI4140K-32 1A Quad HSS 80 mΩ

VIPowertechnology PowerSSO-36PowerSO-36

150 mΩVN808/CM

0.5A Octal HSS

150 mΩVN808/CM-32 1A Octal HSS

VNI8200XP 0.5A Octal HSS

ISO8200B 0.5A Octal HSS

ISO8200A 0.5A Octal HSS

QFN 9x11 32L

110 mΩ

VNI8200XP-32 1A Octal HSS

110 mΩ

110 mΩ 110 mΩ

110 mΩ

IPS Solutions Power stage characteristics

Order code: BRIPS0920

© STMicroelectronics - September 2020 - Printed in United Kingdom - All rights reservedST and ST logo are trademarks or registered trademarks of STMicroelectronics International NV or its affiliates in the EU and/or other countries. For additional information about ST trademarks, please refer to www.st.com/trademarks.

All other product or service names are the property of their respective owners.

For more information on ST products and solutions, visit www.st.com

400 mΩ

400 mΩ 400 mΩ

400 mΩ

400 mΩ

400 mΩ

400 mΩ

DIP-8BCD technology

High Side Switch (HSS)

Low Side Switch (LSS)

SO-8 SO-14HTSSOP20 SO-20

100 mΩ

PowerSO-20

L6370 2A Single

L6375 0.5A Single

L6377 0.5A Single

TDE1897 0.5A Single

TDE1898 0.5A Single

L6374 0.1A Quad

L6376D 0.5A Quad

IPS4260L 0.5 to 2A Quad

260 mΩ

640 mΩ

Notes: (*) Available end Q4 2020

0.5 A

DIP-8Bipolar technology DFN 4x4

0.5 A

SO-8 SO-14

TDE1798Single HSS

TDE1747Single HSS

TDE1708DFTSingle HSS/LSS

TDE1707Single HSS/LSS 0.5 A

0.2 A

0.5 A

0.22 A

BCD technology QFN-26L 3.5x5 DFN-12L 3x3

0.25 A

QFN 20L4x4

L6360

L6362A

L6364Q

0.25 A

CSP 2.5 x 2.5 mm

L6364W (*)

IO-LINK communicationtransceivers